PCI: use dev_printk in x86 quirk messages
Convert quirk printks to dev_printk().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff --git a/arch/x86/pci/fixup.c b/arch/x86/pci/fixup.c
index cb63007..74d30ff 100644
--- a/arch/x86/pci/fixup.c
+++ b/arch/x86/pci/fixup.c
@@ -17,7 +17,7 @@
int pxb, reg;
u8 busno, suba, subb;
- printk(KERN_WARNING "PCI: Searching for i450NX host bridges on %s\n", pci_name(d));
+ dev_warn(&d->dev, "Searching for i450NX host bridges\n");
reg = 0xd0;
for(pxb = 0; pxb < 2; pxb++) {
pci_read_config_byte(d, reg++, &busno);
@@ -41,7 +41,7 @@
*/
u8 busno;
pci_read_config_byte(d, 0x4a, &busno);
- printk(KERN_INFO "PCI: i440KX/GX host bridge %s: secondary bus %02x\n", pci_name(d), busno);
+ dev_info(&d->dev, "i440KX/GX host bridge; secondary bus %02x\n", busno);
pci_scan_bus_with_sysdata(busno);
pcibios_last_bus = -1;
}
@@ -55,7 +55,7 @@
*/
int i;
- printk(KERN_WARNING "PCI: Fixing base address flags for device %s\n", pci_name(d));
+ dev_warn(&d->dev, "Fixing base address flags\n");
for(i = 0; i < 4; i++)
d->resource[i].flags |= PCI_BASE_ADDRESS_SPACE_IO;
}
@@ -68,7 +68,7 @@
* Fix class to be PCI_CLASS_STORAGE_SCSI
*/
if (!d->class) {
- printk(KERN_WARNING "PCI: fixing NCR 53C810 class code for %s\n", pci_name(d));
+ dev_warn(&d->dev, "Fixing NCR 53C810 class code\n");
d->class = PCI_CLASS_STORAGE_SCSI << 8;
}
}
@@ -80,7 +80,7 @@
* SiS 5597 and 5598 chipsets require latency timer set to
* at most 32 to avoid lockups.
*/
- DBG("PCI: Setting max latency to 32\n");
+ dev_dbg(&d->dev, "Setting max latency to 32\n");
pcibios_max_latency = 32;
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5597, pci_fixup_latency);
@@ -138,7 +138,7 @@
pci_read_config_byte(d, where, &v);
if (v & ~mask) {
- printk(KERN_WARNING "Disabling VIA memory write queue (PCI ID %04x, rev %02x): [%02x] %02x & %02x -> %02x\n", \
+ dev_warn(&d->dev, "Disabling VIA memory write queue (PCI ID %04x, rev %02x): [%02x] %02x & %02x -> %02x\n", \
d->device, d->revision, where, v, mask, v & mask);
v &= mask;
pci_write_config_byte(d, where, v);
@@ -200,7 +200,7 @@
* Apply fixup if needed, but don't touch disconnect state
*/
if ((val & 0x00FF0000) != 0x00010000) {
- printk(KERN_WARNING "PCI: nForce2 C1 Halt Disconnect fixup\n");
+ dev_warn(&dev->dev, "nForce2 C1 Halt Disconnect fixup\n");
pci_write_config_dword(dev, 0x6c, (val & 0xFF00FFFF) | 0x00010000);
}
}
@@ -348,7 +348,7 @@
pci_read_config_word(pdev, PCI_COMMAND, &config);
if (config & (PCI_COMMAND_IO | PCI_COMMAND_MEMORY)) {
pdev->resource[PCI_ROM_RESOURCE].flags |= IORESOURCE_ROM_SHADOW;
- printk(KERN_DEBUG "Boot video device is %s\n", pci_name(pdev));
+ dev_printk(KERN_DEBUG, &pdev->dev, "Boot video device\n");
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_ANY_ID, PCI_ANY_ID, pci_fixup_video);
@@ -388,11 +388,11 @@
/* verify the change for status output */
pci_read_config_byte(dev, 0x50, &val);
if (val & 0x40)
- printk(KERN_INFO "PCI: Detected MSI K8T Neo2-FIR, "
+ dev_info(&dev->dev, "Detected MSI K8T Neo2-FIR; "
"can't enable onboard soundcard!\n");
else
- printk(KERN_INFO "PCI: Detected MSI K8T Neo2-FIR, "
- "enabled onboard soundcard.\n");
+ dev_info(&dev->dev, "Detected MSI K8T Neo2-FIR; "
+ "enabled onboard soundcard\n");
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237,