arch/arm64/boot/dts/broadcom/ns2.dtsi - kernel/msm-4.9 - Gitiles

 /*
  *  BSD LICENSE
  *
  *  Copyright(c) 2015 Broadcom Corporation.  All rights reserved.
  *
  *  Redistribution and use in source and binary forms, with or without
  *  modification, are permitted provided that the following conditions
  *  are met:
  *
  *    * Redistributions of source code must retain the above copyright
  *      notice, this list of conditions and the following disclaimer.
  *    * Redistributions in binary form must reproduce the above copyright
  *      notice, this list of conditions and the following disclaimer in
  *      the documentation and/or other materials provided with the
  *      distribution.
  *    * Neither the name of Broadcom Corporation nor the names of its
  *      contributors may be used to endorse or promote products derived
  *      from this software without specific prior written permission.
  *
  *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
  *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
  *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
  *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
  *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
  *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
  *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
  *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
  *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
  *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  */

 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/bcm-ns2.h>

 /memreserve/ 0x84b00000 0x00000008;

 / {
 	compatible = "brcm,ns2";
 	interrupt-parent = <&gic>;
 	#address-cells = <2>;
 	#size-cells = <2>;

 	cpus {
 		#address-cells = <2>;
 		#size-cells = <0>;

 		A57_0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a57", "arm,armv8";
 			reg = <0 0>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0 0x84b00000>;
 			next-level-cache = <&CLUSTER0_L2>;
 		};

 		A57_1: cpu@1 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a57", "arm,armv8";
 			reg = <0 1>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0 0x84b00000>;
 			next-level-cache = <&CLUSTER0_L2>;
 		};

 		A57_2: cpu@2 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a57", "arm,armv8";
 			reg = <0 2>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0 0x84b00000>;
 			next-level-cache = <&CLUSTER0_L2>;
 		};

 		A57_3: cpu@3 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a57", "arm,armv8";
 			reg = <0 3>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0 0x84b00000>;
 			next-level-cache = <&CLUSTER0_L2>;
 		};

 		CLUSTER0_L2: l2-cache@000 {
 			compatible = "cache";
 		};
 	};

 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(0xff) |
 			      IRQ_TYPE_EDGE_RISING)>,
 			     <GIC_PPI 14 (GIC_CPU_MASK_RAW(0xff) |
 			      IRQ_TYPE_EDGE_RISING)>,
 			     <GIC_PPI 11 (GIC_CPU_MASK_RAW(0xff) |
 			      IRQ_TYPE_EDGE_RISING)>,
 			     <GIC_PPI 10 (GIC_CPU_MASK_RAW(0xff) |
 			      IRQ_TYPE_EDGE_RISING)>;
 	};

 	pmu {
 		compatible = "arm,armv8-pmuv3";
 		interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-affinity = <&A57_0>,
 				     <&A57_1>,
 				     <&A57_2>,
 				     <&A57_3>;
 	};

 	clocks {
 		#address-cells = <1>;
 		#size-cells = <1>;

 		osc: oscillator {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <25000000>;
 		};

 		iprocmed: iprocmed {
 			#clock-cells = <0>;
 			compatible = "fixed-factor-clock";
 			clocks = <&genpll_scr BCM_NS2_GENPLL_SCR_SCR_CLK>;
 			clock-div = <2>;
 			clock-mult = <1>;
 		};

 		iprocslow: iprocslow {
 			#clock-cells = <0>;
 			compatible = "fixed-factor-clock";
 			clocks = <&genpll_scr BCM_NS2_GENPLL_SCR_SCR_CLK>;
 			clock-div = <4>;
 			clock-mult = <1>;
 		};
 	};

 	pcie0: pcie@20020000 {
 		compatible = "brcm,iproc-pcie";
 		reg = <0 0x20020000 0 0x1000>;

 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
 		interrupt-map = <0 0 0 0 &gic GIC_SPI 281 IRQ_TYPE_NONE>;

 		linux,pci-domain = <0>;

 		bus-range = <0x00 0xff>;

 		#address-cells = <3>;
 		#size-cells = <2>;
 		device_type = "pci";
 		ranges = <0x83000000 0 0x00000000 0 0x00000000 0 0x20000000>;

 		brcm,pcie-ob;
 		brcm,pcie-ob-oarr-size;
 		brcm,pcie-ob-axi-offset = <0x00000000>;
 		brcm,pcie-ob-window-size = <256>;

 		status = "disabled";

 		msi-parent = <&msi0>;
 		msi0: msi@20020000 {
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
 			interrupts = <GIC_SPI 277 IRQ_TYPE_NONE>,
 				     <GIC_SPI 278 IRQ_TYPE_NONE>,
 				     <GIC_SPI 279 IRQ_TYPE_NONE>,
 				     <GIC_SPI 280 IRQ_TYPE_NONE>;
 			brcm,num-eq-region = <1>;
 			brcm,num-msi-msg-region = <1>;
 		};
 	};

 	pcie4: pcie@50020000 {
 		compatible = "brcm,iproc-pcie";
 		reg = <0 0x50020000 0 0x1000>;

 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
 		interrupt-map = <0 0 0 0 &gic GIC_SPI 305 IRQ_TYPE_NONE>;

 		linux,pci-domain = <4>;

 		bus-range = <0x00 0xff>;

 		#address-cells = <3>;
 		#size-cells = <2>;
 		device_type = "pci";
 		ranges = <0x83000000 0 0x00000000 0 0x30000000 0 0x20000000>;

 		brcm,pcie-ob;
 		brcm,pcie-ob-oarr-size;
 		brcm,pcie-ob-axi-offset = <0x30000000>;
 		brcm,pcie-ob-window-size = <256>;

 		status = "disabled";

 		msi-parent = <&msi4>;
 		msi4: msi@50020000 {
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
 			interrupts = <GIC_SPI 301 IRQ_TYPE_NONE>,
 				     <GIC_SPI 302 IRQ_TYPE_NONE>,
 				     <GIC_SPI 303 IRQ_TYPE_NONE>,
 				     <GIC_SPI 304 IRQ_TYPE_NONE>;
 		};
 	};

 	soc: soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0 0 0xffffffff>;

 		smmu: mmu@64000000 {
 			compatible = "arm,mmu-500";
 			reg = <0x64000000 0x40000>;
 			#global-interrupts = <2>;
 			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>;
 			mmu-masters;
 		};

 		lcpll_ddr: lcpll_ddr@6501d058 {
 			#clock-cells = <1>;
 			compatible = "brcm,ns2-lcpll-ddr";
 			reg = <0x6501d058 0x20>,
 			      <0x6501c020 0x4>,
 			      <0x6501d04c 0x4>;
 			clocks = <&osc>;
 			clock-output-names = "lcpll_ddr", "pcie_sata_usb",
 					     "ddr", "ddr_ch2_unused",
 					     "ddr_ch3_unused", "ddr_ch4_unused",
 					     "ddr_ch5_unused";
 		};

 		lcpll_ports: lcpll_ports@6501d078 {
 			#clock-cells = <1>;
 			compatible = "brcm,ns2-lcpll-ports";
 			reg = <0x6501d078 0x20>,
 			      <0x6501c020 0x4>,
 			      <0x6501d054 0x4>;
 			clocks = <&osc>;
 			clock-output-names = "lcpll_ports", "wan", "rgmii",
 					     "ports_ch2_unused",
 					     "ports_ch3_unused",
 					     "ports_ch4_unused",
 					     "ports_ch5_unused";
 		};

 		genpll_scr: genpll_scr@6501d098 {
 			#clock-cells = <1>;
 			compatible = "brcm,ns2-genpll-scr";
 			reg = <0x6501d098 0x32>,
 			      <0x6501c020 0x4>,
 			      <0x6501d044 0x4>;
 			clocks = <&osc>;
 			clock-output-names = "genpll_scr", "scr", "fs",
 					     "audio_ref", "scr_ch3_unused",
 					     "scr_ch4_unused", "scr_ch5_unused";
 		};

 		genpll_sw: genpll_sw@6501d0c4 {
 			#clock-cells = <1>;
 			compatible = "brcm,ns2-genpll-sw";
 			reg = <0x6501d0c4 0x32>,
 			      <0x6501c020 0x4>,
 			      <0x6501d044 0x4>;
 			clocks = <&osc>;
 			clock-output-names = "genpll_sw", "rpe", "250", "nic",
 					     "chimp", "port", "sdio";
 		};

 		crmu: crmu@65024000 {
 			compatible = "syscon";
 			reg = <0x65024000 0x100>;
 		};

 		reboot@65024000 {
 			compatible ="syscon-reboot";
 			regmap = <&crmu>;
 			offset = <0x90>;
 			mask = <0xfffffffd>;
 		};

 		gic: interrupt-controller@65210000 {
 			compatible = "arm,gic-400";
 			#interrupt-cells = <3>;
 			interrupt-controller;
 			reg = <0x65210000 0x1000>,
 			      <0x65220000 0x1000>,
 			      <0x65240000 0x2000>,
 			      <0x65260000 0x1000>;
 		};

 		timer0: timer@66030000 {
 			compatible = "arm,sp804", "arm,primecell";
 			reg = <0x66030000 0x1000>;
 			interrupts = <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&iprocslow>,
 				 <&iprocslow>,
 				 <&iprocslow>;
 			clock-names = "timer1", "timer2", "apb_pclk";
 		};

 		timer1: timer@66040000 {
 			compatible = "arm,sp804", "arm,primecell";
 			reg = <0x66040000 0x1000>;
 			interrupts = <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&iprocslow>,
 				 <&iprocslow>,
 				 <&iprocslow>;
 			clock-names = "timer1", "timer2", "apb_pclk";
 		};

 		timer2: timer@66050000 {
 			compatible = "arm,sp804", "arm,primecell";
 			reg = <0x66050000 0x1000>;
 			interrupts = <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&iprocslow>,
 				 <&iprocslow>,
 				 <&iprocslow>;
 			clock-names = "timer1", "timer2", "apb_pclk";
 		};

 		timer3: timer@66060000 {
 			compatible = "arm,sp804", "arm,primecell";
 			reg = <0x66060000 0x1000>;
 			interrupts = <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&iprocslow>,
 				 <&iprocslow>,
 				 <&iprocslow>;
 			clock-names = "timer1", "timer2", "apb_pclk";
 		};

 		i2c0: i2c@66080000 {
 			compatible = "brcm,iproc-i2c";
 			reg = <0x66080000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			interrupts = <GIC_SPI 394 IRQ_TYPE_NONE>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};

 		wdt0: watchdog@66090000 {
 			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x66090000 0x1000>;
 			interrupts = <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&iprocslow>, <&iprocslow>;
 			clock-names = "wdogclk", "apb_pclk";
 		};

 		i2c1: i2c@660b0000 {
 			compatible = "brcm,iproc-i2c";
 			reg = <0x660b0000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			interrupts = <GIC_SPI 395 IRQ_TYPE_NONE>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};

 		uart3: serial@66130000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x66130000 0x100>;
 			interrupts = <GIC_SPI 393 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&osc>;
 			status = "disabled";
 		};

 		hwrng: hwrng@66220000 {
 			compatible = "brcm,iproc-rng200";
 			reg = <0x66220000 0x28>;
 		};

 		sdio0: sdhci@66420000 {
 			compatible = "brcm,sdhci-iproc-cygnus";
 			reg = <0x66420000 0x100>;
 			interrupts = <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>;
 			bus-width = <8>;
 			clocks = <&genpll_sw BCM_NS2_GENPLL_SW_SDIO_CLK>;
 			status = "disabled";
 		};

 		sdio1: sdhci@66430000 {
 			compatible = "brcm,sdhci-iproc-cygnus";
 			reg = <0x66430000 0x100>;
 			interrupts = <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>;
 			bus-width = <8>;
 			clocks = <&genpll_sw BCM_NS2_GENPLL_SW_SDIO_CLK>;
 			status = "disabled";
 		};

 		nand: nand@66460000 {
 			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
 			reg = <0x66460000 0x600>,
 			      <0x67015408 0x600>,
 			      <0x66460f00 0x20>;
 			reg-names = "nand", "iproc-idm", "iproc-ext";
 			interrupts = <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>;

 			#address-cells = <1>;
 			#size-cells = <0>;

 			brcm,nand-has-wp;
 		};
 	};
 };
	/*
	* BSD LICENSE
	*
	* Copyright(c) 2015 Broadcom Corporation. All rights reserved.
	*
	* Redistribution and use in source and binary forms, with or without
	* modification, are permitted provided that the following conditions
	* are met:
	*
	* * Redistributions of source code must retain the above copyright
	* notice, this list of conditions and the following disclaimer.
	* * Redistributions in binary form must reproduce the above copyright
	* notice, this list of conditions and the following disclaimer in
	* the documentation and/or other materials provided with the
	* distribution.
	* * Neither the name of Broadcom Corporation nor the names of its
	* contributors may be used to endorse or promote products derived
	* from this software without specific prior written permission.
	*
	* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
	* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
	* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
	* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
	* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
	* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
	* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
	* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
	* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
	* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
	* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
	*/

	#include <dt-bindings/interrupt-controller/arm-gic.h>
	#include <dt-bindings/clock/bcm-ns2.h>

	/memreserve/ 0x84b00000 0x00000008;

	/ {
	compatible = "brcm,ns2";
	interrupt-parent = <&gic>;
	#address-cells = <2>;
	#size-cells = <2>;

	cpus {
	#address-cells = <2>;
	#size-cells = <0>;

	A57_0: cpu@0 {
	device_type = "cpu";
	compatible = "arm,cortex-a57", "arm,armv8";
	reg = <0 0>;
	enable-method = "spin-table";
	cpu-release-addr = <0 0x84b00000>;
	next-level-cache = <&CLUSTER0_L2>;
	};

	A57_1: cpu@1 {
	device_type = "cpu";
	compatible = "arm,cortex-a57", "arm,armv8";
	reg = <0 1>;
	enable-method = "spin-table";
	cpu-release-addr = <0 0x84b00000>;
	next-level-cache = <&CLUSTER0_L2>;
	};

	A57_2: cpu@2 {
	device_type = "cpu";
	compatible = "arm,cortex-a57", "arm,armv8";
	reg = <0 2>;
	enable-method = "spin-table";
	cpu-release-addr = <0 0x84b00000>;
	next-level-cache = <&CLUSTER0_L2>;
	};

	A57_3: cpu@3 {
	device_type = "cpu";
	compatible = "arm,cortex-a57", "arm,armv8";
	reg = <0 3>;
	enable-method = "spin-table";
	cpu-release-addr = <0 0x84b00000>;
	next-level-cache = <&CLUSTER0_L2>;
	};

	CLUSTER0_L2: l2-cache@000 {
	compatible = "cache";
	};
	};

	timer {
	compatible = "arm,armv8-timer";
	interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(0xff) \|
	IRQ_TYPE_EDGE_RISING)>,
	<GIC_PPI 14 (GIC_CPU_MASK_RAW(0xff) \|
	IRQ_TYPE_EDGE_RISING)>,
	<GIC_PPI 11 (GIC_CPU_MASK_RAW(0xff) \|
	IRQ_TYPE_EDGE_RISING)>,
	<GIC_PPI 10 (GIC_CPU_MASK_RAW(0xff) \|
	IRQ_TYPE_EDGE_RISING)>;
	};

	pmu {
	compatible = "arm,armv8-pmuv3";
	interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>;
	interrupt-affinity = <&A57_0>,
	<&A57_1>,
	<&A57_2>,
	<&A57_3>;
	};

	clocks {
	#address-cells = <1>;
	#size-cells = <1>;

	osc: oscillator {
	#clock-cells = <0>;
	compatible = "fixed-clock";
	clock-frequency = <25000000>;
	};

	iprocmed: iprocmed {
	#clock-cells = <0>;
	compatible = "fixed-factor-clock";
	clocks = <&genpll_scr BCM_NS2_GENPLL_SCR_SCR_CLK>;
	clock-div = <2>;
	clock-mult = <1>;
	};

	iprocslow: iprocslow {
	#clock-cells = <0>;
	compatible = "fixed-factor-clock";
	clocks = <&genpll_scr BCM_NS2_GENPLL_SCR_SCR_CLK>;
	clock-div = <4>;
	clock-mult = <1>;
	};
	};

	pcie0: pcie@20020000 {
	compatible = "brcm,iproc-pcie";
	reg = <0 0x20020000 0 0x1000>;

	#interrupt-cells = <1>;
	interrupt-map-mask = <0 0 0 0>;
	interrupt-map = <0 0 0 0 &gic GIC_SPI 281 IRQ_TYPE_NONE>;

	linux,pci-domain = <0>;

	bus-range = <0x00 0xff>;

	#address-cells = <3>;
	#size-cells = <2>;
	device_type = "pci";
	ranges = <0x83000000 0 0x00000000 0 0x00000000 0 0x20000000>;

	brcm,pcie-ob;
	brcm,pcie-ob-oarr-size;
	brcm,pcie-ob-axi-offset = <0x00000000>;
	brcm,pcie-ob-window-size = <256>;

	status = "disabled";

	msi-parent = <&msi0>;
	msi0: msi@20020000 {
	compatible = "brcm,iproc-msi";
	msi-controller;
	interrupt-parent = <&gic>;
	interrupts = <GIC_SPI 277 IRQ_TYPE_NONE>,
	<GIC_SPI 278 IRQ_TYPE_NONE>,
	<GIC_SPI 279 IRQ_TYPE_NONE>,
	<GIC_SPI 280 IRQ_TYPE_NONE>;
	brcm,num-eq-region = <1>;
	brcm,num-msi-msg-region = <1>;
	};
	};

	pcie4: pcie@50020000 {
	compatible = "brcm,iproc-pcie";
	reg = <0 0x50020000 0 0x1000>;

	#interrupt-cells = <1>;
	interrupt-map-mask = <0 0 0 0>;
	interrupt-map = <0 0 0 0 &gic GIC_SPI 305 IRQ_TYPE_NONE>;

	linux,pci-domain = <4>;

	bus-range = <0x00 0xff>;

	#address-cells = <3>;
	#size-cells = <2>;
	device_type = "pci";
	ranges = <0x83000000 0 0x00000000 0 0x30000000 0 0x20000000>;

	brcm,pcie-ob;
	brcm,pcie-ob-oarr-size;
	brcm,pcie-ob-axi-offset = <0x30000000>;
	brcm,pcie-ob-window-size = <256>;

	status = "disabled";

	msi-parent = <&msi4>;
	msi4: msi@50020000 {
	compatible = "brcm,iproc-msi";
	msi-controller;
	interrupt-parent = <&gic>;
	interrupts = <GIC_SPI 301 IRQ_TYPE_NONE>,
	<GIC_SPI 302 IRQ_TYPE_NONE>,
	<GIC_SPI 303 IRQ_TYPE_NONE>,
	<GIC_SPI 304 IRQ_TYPE_NONE>;
	};
	};

	soc: soc {
	compatible = "simple-bus";
	#address-cells = <1>;
	#size-cells = <1>;
	ranges = <0 0 0 0xffffffff>;

	smmu: mmu@64000000 {
	compatible = "arm,mmu-500";
	reg = <0x64000000 0x40000>;
	#global-interrupts = <2>;
	interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>,
	<GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>;
	mmu-masters;
	};

	lcpll_ddr: lcpll_ddr@6501d058 {
	#clock-cells = <1>;
	compatible = "brcm,ns2-lcpll-ddr";
	reg = <0x6501d058 0x20>,
	<0x6501c020 0x4>,
	<0x6501d04c 0x4>;
	clocks = <&osc>;
	clock-output-names = "lcpll_ddr", "pcie_sata_usb",
	"ddr", "ddr_ch2_unused",
	"ddr_ch3_unused", "ddr_ch4_unused",
	"ddr_ch5_unused";
	};

	lcpll_ports: lcpll_ports@6501d078 {
	#clock-cells = <1>;
	compatible = "brcm,ns2-lcpll-ports";
	reg = <0x6501d078 0x20>,
	<0x6501c020 0x4>,
	<0x6501d054 0x4>;
	clocks = <&osc>;
	clock-output-names = "lcpll_ports", "wan", "rgmii",
	"ports_ch2_unused",
	"ports_ch3_unused",
	"ports_ch4_unused",
	"ports_ch5_unused";
	};

	genpll_scr: genpll_scr@6501d098 {
	#clock-cells = <1>;
	compatible = "brcm,ns2-genpll-scr";
	reg = <0x6501d098 0x32>,
	<0x6501c020 0x4>,
	<0x6501d044 0x4>;
	clocks = <&osc>;
	clock-output-names = "genpll_scr", "scr", "fs",
	"audio_ref", "scr_ch3_unused",
	"scr_ch4_unused", "scr_ch5_unused";
	};

	genpll_sw: genpll_sw@6501d0c4 {
	#clock-cells = <1>;
	compatible = "brcm,ns2-genpll-sw";
	reg = <0x6501d0c4 0x32>,
	<0x6501c020 0x4>,
	<0x6501d044 0x4>;
	clocks = <&osc>;
	clock-output-names = "genpll_sw", "rpe", "250", "nic",
	"chimp", "port", "sdio";
	};

	crmu: crmu@65024000 {
	compatible = "syscon";
	reg = <0x65024000 0x100>;
	};

	reboot@65024000 {
	compatible ="syscon-reboot";
	regmap = <&crmu>;
	offset = <0x90>;
	mask = <0xfffffffd>;
	};

	gic: interrupt-controller@65210000 {
	compatible = "arm,gic-400";
	#interrupt-cells = <3>;
	interrupt-controller;
	reg = <0x65210000 0x1000>,
	<0x65220000 0x1000>,
	<0x65240000 0x2000>,
	<0x65260000 0x1000>;
	};

	timer0: timer@66030000 {
	compatible = "arm,sp804", "arm,primecell";
	reg = <0x66030000 0x1000>;
	interrupts = <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>;
	clocks = <&iprocslow>,
	<&iprocslow>,
	<&iprocslow>;
	clock-names = "timer1", "timer2", "apb_pclk";
	};

	timer1: timer@66040000 {
	compatible = "arm,sp804", "arm,primecell";
	reg = <0x66040000 0x1000>;
	interrupts = <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>;
	clocks = <&iprocslow>,
	<&iprocslow>,
	<&iprocslow>;
	clock-names = "timer1", "timer2", "apb_pclk";
	};

	timer2: timer@66050000 {
	compatible = "arm,sp804", "arm,primecell";
	reg = <0x66050000 0x1000>;
	interrupts = <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>;
	clocks = <&iprocslow>,
	<&iprocslow>,
	<&iprocslow>;
	clock-names = "timer1", "timer2", "apb_pclk";
	};

	timer3: timer@66060000 {
	compatible = "arm,sp804", "arm,primecell";
	reg = <0x66060000 0x1000>;
	interrupts = <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>;
	clocks = <&iprocslow>,
	<&iprocslow>,
	<&iprocslow>;
	clock-names = "timer1", "timer2", "apb_pclk";
	};

	i2c0: i2c@66080000 {
	compatible = "brcm,iproc-i2c";
	reg = <0x66080000 0x100>;
	#address-cells = <1>;
	#size-cells = <0>;
	interrupts = <GIC_SPI 394 IRQ_TYPE_NONE>;
	clock-frequency = <100000>;
	status = "disabled";
	};

	wdt0: watchdog@66090000 {
	compatible = "arm,sp805", "arm,primecell";
	reg = <0x66090000 0x1000>;
	interrupts = <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>;
	clocks = <&iprocslow>, <&iprocslow>;
	clock-names = "wdogclk", "apb_pclk";
	};

	i2c1: i2c@660b0000 {
	compatible = "brcm,iproc-i2c";
	reg = <0x660b0000 0x100>;
	#address-cells = <1>;
	#size-cells = <0>;
	interrupts = <GIC_SPI 395 IRQ_TYPE_NONE>;
	clock-frequency = <100000>;
	status = "disabled";
	};

	uart3: serial@66130000 {
	compatible = "snps,dw-apb-uart";
	reg = <0x66130000 0x100>;
	interrupts = <GIC_SPI 393 IRQ_TYPE_LEVEL_HIGH>;
	reg-shift = <2>;
	reg-io-width = <4>;
	clocks = <&osc>;
	status = "disabled";
	};

	hwrng: hwrng@66220000 {
	compatible = "brcm,iproc-rng200";
	reg = <0x66220000 0x28>;
	};

	sdio0: sdhci@66420000 {
	compatible = "brcm,sdhci-iproc-cygnus";
	reg = <0x66420000 0x100>;
	interrupts = <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>;
	bus-width = <8>;
	clocks = <&genpll_sw BCM_NS2_GENPLL_SW_SDIO_CLK>;
	status = "disabled";
	};

	sdio1: sdhci@66430000 {
	compatible = "brcm,sdhci-iproc-cygnus";
	reg = <0x66430000 0x100>;
	interrupts = <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>;
	bus-width = <8>;
	clocks = <&genpll_sw BCM_NS2_GENPLL_SW_SDIO_CLK>;
	status = "disabled";
	};

	nand: nand@66460000 {
	compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
	reg = <0x66460000 0x600>,
	<0x67015408 0x600>,
	<0x66460f00 0x20>;
	reg-names = "nand", "iproc-idm", "iproc-ext";
	interrupts = <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>;

	#address-cells = <1>;
	#size-cells = <0>;

	brcm,nand-has-wp;
	};
	};
	};