arm: omap: board-sdp3430: use sharp panel's gpio handling
The omap3430sdp board file currently requests gpios required by the sharp_ls dpi
panel, and provides platform_enable/disable callbacks to configure them.
These tasks have been moved to the sharp_ls panel driver itself and shouldn't
be done in the board files.
Remove the gpio requests and the platform callbacks from the board file.
Add the gpio information to panel_sharp_ls037v7dw01_data so that it's
passed to the panel driver.
Out of sharp panel's configurable pins, all apart from resb_gpio are managed by
a CPLD on the display and set to a default value. Only the configurable pin is
passed to platform data.
The backlight GPIO doesn't go directly to the sharp panel, it is used to set up
a voltage supply which goes to the LED+ pin of the panel, hence it isn't passed
to panel as platform data, and configured in the board file itself. The
backlight used to previously toggle through the platform_enable/disable
callbacks, but now it is always on. This needs to be revisited.
Signed-off-by: Archit Taneja <archit@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c
index 2612eea..66cfcca 100644
--- a/arch/arm/mach-omap2/board-3430sdp.c
+++ b/arch/arm/mach-omap2/board-3430sdp.c
@@ -108,36 +108,24 @@
#define SDP3430_LCD_PANEL_BACKLIGHT_GPIO 8
#define SDP3430_LCD_PANEL_ENABLE_GPIO 5
-static struct gpio sdp3430_dss_gpios[] __initdata = {
- {SDP3430_LCD_PANEL_ENABLE_GPIO, GPIOF_OUT_INIT_LOW, "LCD reset" },
- {SDP3430_LCD_PANEL_BACKLIGHT_GPIO, GPIOF_OUT_INIT_LOW, "LCD Backlight"},
-};
-
static void __init sdp3430_display_init(void)
{
int r;
- r = gpio_request_array(sdp3430_dss_gpios,
- ARRAY_SIZE(sdp3430_dss_gpios));
+ /*
+ * the backlight GPIO doesn't directly go to the panel, it enables
+ * an internal circuit on 3430sdp to create the signal V_BKL_28V,
+ * this is connected to LED+ pin of the sharp panel. This GPIO
+ * is left enabled in the board file, and not passed to the panel
+ * as platform_data.
+ */
+ r = gpio_request_one(SDP3430_LCD_PANEL_BACKLIGHT_GPIO,
+ GPIOF_OUT_INIT_HIGH, "LCD Backlight");
if (r)
- printk(KERN_ERR "failed to get LCD control GPIOs\n");
+ pr_err("failed to get LCD Backlight GPIO\n");
}
-static int sdp3430_panel_enable_lcd(struct omap_dss_device *dssdev)
-{
- gpio_direction_output(SDP3430_LCD_PANEL_ENABLE_GPIO, 1);
- gpio_direction_output(SDP3430_LCD_PANEL_BACKLIGHT_GPIO, 1);
-
- return 0;
-}
-
-static void sdp3430_panel_disable_lcd(struct omap_dss_device *dssdev)
-{
- gpio_direction_output(SDP3430_LCD_PANEL_ENABLE_GPIO, 0);
- gpio_direction_output(SDP3430_LCD_PANEL_BACKLIGHT_GPIO, 0);
-}
-
static int sdp3430_panel_enable_tv(struct omap_dss_device *dssdev)
{
return 0;
@@ -147,14 +135,20 @@
{
}
+static struct panel_sharp_ls037v7dw01_data sdp3430_lcd_data = {
+ .resb_gpio = SDP3430_LCD_PANEL_ENABLE_GPIO,
+ .ini_gpio = -1,
+ .mo_gpio = -1,
+ .lr_gpio = -1,
+ .ud_gpio = -1,
+};
static struct omap_dss_device sdp3430_lcd_device = {
.name = "lcd",
.driver_name = "sharp_ls_panel",
.type = OMAP_DISPLAY_TYPE_DPI,
.phy.dpi.data_lines = 16,
- .platform_enable = sdp3430_panel_enable_lcd,
- .platform_disable = sdp3430_panel_disable_lcd,
+ .data = &sdp3430_lcd_data,
};
static struct tfp410_platform_data dvi_panel = {