| /****************************************************************************** |
| * |
| * This file is provided under a dual BSD/GPLv2 license. When using or |
| * redistributing this file, you may do so under either license. |
| * |
| * GPL LICENSE SUMMARY |
| * |
| * Copyright(c) 2007 - 2012 Intel Corporation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of version 2 of the GNU General Public License as |
| * published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, but |
| * WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU |
| * General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110, |
| * USA |
| * |
| * The full GNU General Public License is included in this distribution |
| * in the file called LICENSE.GPL. |
| * |
| * Contact Information: |
| * Intel Linux Wireless <ilw@linux.intel.com> |
| * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 |
| * |
| * BSD LICENSE |
| * |
| * Copyright(c) 2005 - 2012 Intel Corporation. All rights reserved. |
| * All rights reserved. |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions |
| * are met: |
| * |
| * * Redistributions of source code must retain the above copyright |
| * notice, this list of conditions and the following disclaimer. |
| * * Redistributions in binary form must reproduce the above copyright |
| * notice, this list of conditions and the following disclaimer in |
| * the documentation and/or other materials provided with the |
| * distribution. |
| * * Neither the name Intel Corporation nor the names of its |
| * contributors may be used to endorse or promote products derived |
| * from this software without specific prior written permission. |
| * |
| * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS |
| * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT |
| * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR |
| * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT |
| * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, |
| * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT |
| * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, |
| * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY |
| * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT |
| * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE |
| * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
| * |
| *****************************************************************************/ |
| #ifndef __iwl_shared_h__ |
| #define __iwl_shared_h__ |
| |
| #include <linux/types.h> |
| #include <linux/spinlock.h> |
| #include <linux/gfp.h> |
| #include <net/mac80211.h> |
| |
| #include "iwl-commands.h" |
| #include "iwl-fw.h" |
| |
| /** |
| * DOC: shared area - role and goal |
| * |
| * The shared area contains all the data exported by the upper layer to the |
| * other layers. Since the bus and transport layer shouldn't dereference |
| * iwl_priv, all the data needed by the upper layer and the transport / bus |
| * layer must be here. |
| * The shared area also holds pointer to all the other layers. This allows a |
| * layer to call a function from another layer. |
| * |
| * NOTE: All the layers hold a pointer to the shared area which must be shrd. |
| * A few macros assume that (_m)->shrd points to the shared area no matter |
| * what _m is. |
| * |
| * gets notifications about enumeration, suspend, resume. |
| * For the moment, the bus layer is not a linux kernel module as itself, and |
| * the module_init function of the driver must call the bus specific |
| * registration functions. These functions are listed at the end of this file. |
| * For the moment, there is only one implementation of this interface: PCI-e. |
| * This implementation is iwl-pci.c |
| */ |
| |
| struct iwl_priv; |
| struct iwl_trans; |
| struct iwl_sensitivity_ranges; |
| struct iwl_trans_ops; |
| |
| #define DRV_NAME "iwlwifi" |
| #define IWLWIFI_VERSION "in-tree:" |
| #define DRV_COPYRIGHT "Copyright(c) 2003-2012 Intel Corporation" |
| #define DRV_AUTHOR "<ilw@linux.intel.com>" |
| |
| extern struct iwl_mod_params iwlagn_mod_params; |
| |
| #define IWL_DISABLE_HT_ALL BIT(0) |
| #define IWL_DISABLE_HT_TXAGG BIT(1) |
| #define IWL_DISABLE_HT_RXAGG BIT(2) |
| |
| /** |
| * struct iwl_mod_params |
| * |
| * Holds the module parameters |
| * |
| * @sw_crypto: using hardware encryption, default = 0 |
| * @disable_11n: disable 11n capabilities, default = 0, |
| * use IWL_DISABLE_HT_* constants |
| * @amsdu_size_8K: enable 8K amsdu size, default = 1 |
| * @antenna: both antennas (use diversity), default = 0 |
| * @restart_fw: restart firmware, default = 1 |
| * @plcp_check: enable plcp health check, default = true |
| * @ack_check: disable ack health check, default = false |
| * @wd_disable: enable stuck queue check, default = 0 |
| * @bt_coex_active: enable bt coex, default = true |
| * @led_mode: system default, default = 0 |
| * @no_sleep_autoadjust: disable autoadjust, default = true |
| * @power_save: disable power save, default = false |
| * @power_level: power level, default = 1 |
| * @debug_level: levels are IWL_DL_* |
| * @ant_coupling: antenna coupling in dB, default = 0 |
| * @bt_ch_announce: BT channel inhibition, default = enable |
| * @wanted_ucode_alternative: ucode alternative to use, default = 1 |
| * @auto_agg: enable agg. without check, default = true |
| */ |
| struct iwl_mod_params { |
| int sw_crypto; |
| unsigned int disable_11n; |
| int amsdu_size_8K; |
| int antenna; |
| int restart_fw; |
| bool plcp_check; |
| bool ack_check; |
| int wd_disable; |
| bool bt_coex_active; |
| int led_mode; |
| bool no_sleep_autoadjust; |
| bool power_save; |
| int power_level; |
| u32 debug_level; |
| int ant_coupling; |
| bool bt_ch_announce; |
| int wanted_ucode_alternative; |
| bool auto_agg; |
| }; |
| |
| /** |
| * struct iwl_hw_params |
| * |
| * Holds the module parameters |
| * |
| * @tx_chains_num: Number of TX chains |
| * @rx_chains_num: Number of RX chains |
| * @valid_tx_ant: usable antennas for TX |
| * @valid_rx_ant: usable antennas for RX |
| * @ht40_channel: is 40MHz width possible: BIT(IEEE80211_BAND_XXX) |
| * @sku: sku read from EEPROM |
| * @rx_page_order: Rx buffer page order |
| * @ct_kill_threshold: temperature threshold - in hw dependent unit |
| * @ct_kill_exit_threshold: when to reeable the device - in hw dependent unit |
| * relevant for 1000, 6000 and up |
| * @wd_timeout: TX queues watchdog timeout |
| * @struct iwl_sensitivity_ranges: range of sensitivity values |
| * @use_rts_for_aggregation: use rts/cts protection for HT traffic |
| */ |
| struct iwl_hw_params { |
| u8 tx_chains_num; |
| u8 rx_chains_num; |
| u8 valid_tx_ant; |
| u8 valid_rx_ant; |
| u8 ht40_channel; |
| bool use_rts_for_aggregation; |
| u16 sku; |
| u32 rx_page_order; |
| u32 ct_kill_threshold; |
| u32 ct_kill_exit_threshold; |
| unsigned int wd_timeout; |
| |
| const struct iwl_sensitivity_ranges *sens; |
| }; |
| |
| /* |
| * LED mode |
| * IWL_LED_DEFAULT: use device default |
| * IWL_LED_RF_STATE: turn LED on/off based on RF state |
| * LED ON = RF ON |
| * LED OFF = RF OFF |
| * IWL_LED_BLINK: adjust led blink rate based on blink table |
| * IWL_LED_DISABLE: led disabled |
| */ |
| enum iwl_led_mode { |
| IWL_LED_DEFAULT, |
| IWL_LED_RF_STATE, |
| IWL_LED_BLINK, |
| IWL_LED_DISABLE, |
| }; |
| |
| /* |
| * @max_ll_items: max number of OTP blocks |
| * @shadow_ram_support: shadow support for OTP memory |
| * @led_compensation: compensate on the led on/off time per HW according |
| * to the deviation to achieve the desired led frequency. |
| * The detail algorithm is described in iwl-led.c |
| * @chain_noise_num_beacons: number of beacons used to compute chain noise |
| * @adv_thermal_throttle: support advance thermal throttle |
| * @support_ct_kill_exit: support ct kill exit condition |
| * @plcp_delta_threshold: plcp error rate threshold used to trigger |
| * radio tuning when there is a high receiving plcp error rate |
| * @chain_noise_scale: default chain noise scale used for gain computation |
| * @wd_timeout: TX queues watchdog timeout |
| * @max_event_log_size: size of event log buffer size for ucode event logging |
| * @shadow_reg_enable: HW shadhow register bit |
| * @hd_v2: v2 of enhanced sensitivity value, used for 2000 series and up |
| * @no_idle_support: do not support idle mode |
| * wd_disable: disable watchdog timer |
| */ |
| struct iwl_base_params { |
| int eeprom_size; |
| int num_of_queues; /* def: HW dependent */ |
| /* for iwl_apm_init() */ |
| u32 pll_cfg_val; |
| |
| const u16 max_ll_items; |
| const bool shadow_ram_support; |
| u16 led_compensation; |
| bool adv_thermal_throttle; |
| bool support_ct_kill_exit; |
| u8 plcp_delta_threshold; |
| s32 chain_noise_scale; |
| unsigned int wd_timeout; |
| u32 max_event_log_size; |
| const bool shadow_reg_enable; |
| const bool hd_v2; |
| const bool no_idle_support; |
| const bool wd_disable; |
| }; |
| |
| /* |
| * @advanced_bt_coexist: support advanced bt coexist |
| * @bt_init_traffic_load: specify initial bt traffic load |
| * @bt_prio_boost: default bt priority boost value |
| * @agg_time_limit: maximum number of uSec in aggregation |
| * @bt_sco_disable: uCode should not response to BT in SCO/ESCO mode |
| */ |
| struct iwl_bt_params { |
| bool advanced_bt_coexist; |
| u8 bt_init_traffic_load; |
| u8 bt_prio_boost; |
| u16 agg_time_limit; |
| bool bt_sco_disable; |
| bool bt_session_2; |
| }; |
| /* |
| * @use_rts_for_aggregation: use rts/cts protection for HT traffic |
| */ |
| struct iwl_ht_params { |
| const bool ht_greenfield_support; /* if used set to true */ |
| bool use_rts_for_aggregation; |
| enum ieee80211_smps_mode smps_mode; |
| }; |
| |
| /** |
| * struct iwl_cfg |
| * @name: Offical name of the device |
| * @fw_name_pre: Firmware filename prefix. The api version and extension |
| * (.ucode) will be added to filename before loading from disk. The |
| * filename is constructed as fw_name_pre<api>.ucode. |
| * @ucode_api_max: Highest version of uCode API supported by driver. |
| * @ucode_api_ok: oldest version of the uCode API that is OK to load |
| * without a warning, for use in transitions |
| * @ucode_api_min: Lowest version of uCode API supported by driver. |
| * @max_inst_size: The maximal length of the fw inst section |
| * @max_data_size: The maximal length of the fw data section |
| * @valid_tx_ant: valid transmit antenna |
| * @valid_rx_ant: valid receive antenna |
| * @eeprom_ver: EEPROM version |
| * @eeprom_calib_ver: EEPROM calibration version |
| * @lib: pointer to the lib ops |
| * @additional_nic_config: additional nic configuration |
| * @base_params: pointer to basic parameters |
| * @ht_params: point to ht patameters |
| * @bt_params: pointer to bt parameters |
| * @need_temp_offset_calib: need to perform temperature offset calibration |
| * @no_xtal_calib: some devices do not need crystal calibration data, |
| * don't send it to those |
| * @led_mode: 0=blinking, 1=On(RF On)/Off(RF Off) |
| * @adv_pm: advance power management |
| * @rx_with_siso_diversity: 1x1 device with rx antenna diversity |
| * @internal_wimax_coex: internal wifi/wimax combo device |
| * @temp_offset_v2: support v2 of temperature offset calibration |
| * |
| * We enable the driver to be backward compatible wrt. hardware features. |
| * API differences in uCode shouldn't be handled here but through TLVs |
| * and/or the uCode API version instead. |
| */ |
| struct iwl_cfg { |
| /* params specific to an individual device within a device family */ |
| const char *name; |
| const char *fw_name_pre; |
| const unsigned int ucode_api_max; |
| const unsigned int ucode_api_ok; |
| const unsigned int ucode_api_min; |
| const u32 max_data_size; |
| const u32 max_inst_size; |
| u8 valid_tx_ant; |
| u8 valid_rx_ant; |
| u16 eeprom_ver; |
| u16 eeprom_calib_ver; |
| const struct iwl_lib_ops *lib; |
| void (*additional_nic_config)(struct iwl_priv *priv); |
| /* params not likely to change within a device family */ |
| const struct iwl_base_params *base_params; |
| /* params likely to change within a device family */ |
| const struct iwl_ht_params *ht_params; |
| const struct iwl_bt_params *bt_params; |
| const bool need_temp_offset_calib; /* if used set to true */ |
| const bool no_xtal_calib; |
| enum iwl_led_mode led_mode; |
| const bool adv_pm; |
| const bool rx_with_siso_diversity; |
| const bool internal_wimax_coex; |
| const bool temp_offset_v2; |
| }; |
| |
| /** |
| * struct iwl_shared - shared fields for all the layers of the driver |
| * |
| * @status: STATUS_* |
| * @wowlan: are we running wowlan uCode |
| * @bus: pointer to the bus layer data |
| * @cfg: see struct iwl_cfg |
| * @priv: pointer to the upper layer data |
| * @trans: pointer to the transport layer data |
| * @nic: pointer to the nic data |
| * @hw_params: see struct iwl_hw_params |
| * @lock: protect general shared data |
| * @eeprom: pointer to the eeprom/OTP image |
| * @ucode_type: indicator of loaded ucode image |
| * @device_pointers: pointers to ucode event tables |
| */ |
| struct iwl_shared { |
| unsigned long status; |
| |
| const struct iwl_cfg *cfg; |
| struct iwl_trans *trans; |
| void *drv; |
| struct iwl_hw_params hw_params; |
| const struct iwl_fw *fw; |
| |
| /* eeprom -- this is in the card's little endian byte order */ |
| u8 *eeprom; |
| |
| /* ucode related variables */ |
| enum iwl_ucode_type ucode_type; |
| |
| struct { |
| u32 error_event_table; |
| u32 log_event_table; |
| } device_pointers; |
| |
| }; |
| |
| /*Whatever _m is (iwl_trans, iwl_priv, these macros will work */ |
| #define cfg(_m) ((_m)->shrd->cfg) |
| #define trans(_m) ((_m)->shrd->trans) |
| #define hw_params(_m) ((_m)->shrd->hw_params) |
| |
| static inline bool iwl_have_debug_level(u32 level) |
| { |
| return iwlagn_mod_params.debug_level & level; |
| } |
| |
| enum iwl_rxon_context_id { |
| IWL_RXON_CTX_BSS, |
| IWL_RXON_CTX_PAN, |
| |
| NUM_IWL_RXON_CTX |
| }; |
| |
| int iwlagn_hw_valid_rtc_data_addr(u32 addr); |
| const char *get_cmd_string(u8 cmd); |
| |
| #define IWL_CMD(x) case x: return #x |
| |
| /***************************************************** |
| * DRIVER STATUS FUNCTIONS |
| ******************************************************/ |
| #define STATUS_HCMD_ACTIVE 0 /* host command in progress */ |
| /* 1 is unused (used to be STATUS_HCMD_SYNC_ACTIVE) */ |
| #define STATUS_INT_ENABLED 2 |
| #define STATUS_RF_KILL_HW 3 |
| #define STATUS_CT_KILL 4 |
| #define STATUS_INIT 5 |
| #define STATUS_ALIVE 6 |
| #define STATUS_READY 7 |
| #define STATUS_TEMPERATURE 8 |
| #define STATUS_GEO_CONFIGURED 9 |
| #define STATUS_EXIT_PENDING 10 |
| #define STATUS_STATISTICS 12 |
| #define STATUS_SCANNING 13 |
| #define STATUS_SCAN_ABORTING 14 |
| #define STATUS_SCAN_HW 15 |
| #define STATUS_POWER_PMI 16 |
| #define STATUS_FW_ERROR 17 |
| #define STATUS_DEVICE_ENABLED 18 |
| #define STATUS_CHANNEL_SWITCH_PENDING 19 |
| #define STATUS_SCAN_COMPLETE 20 |
| |
| #endif /* #__iwl_shared_h__ */ |