blob: 2d1d775f2c3e1fbe4d2b40c1b5caa8b9662421ed [file] [log] [blame]
/*
* common-board-devices.c
*
* Copyright (C) 2011 CompuLab, Ltd.
* Author: Mike Rapoport <mike@compulab.co.il>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
* 02110-1301 USA
*
*/
#include <linux/gpio.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <plat/mcspi.h>
#include <plat/nand.h>
#include "common-board-devices.h"
#if defined(CONFIG_TOUCHSCREEN_ADS7846) || \
defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
static struct omap2_mcspi_device_config ads7846_mcspi_config = {
.turbo_mode = 0,
};
static struct ads7846_platform_data ads7846_config = {
.x_max = 0x0fff,
.y_max = 0x0fff,
.x_plate_ohms = 180,
.pressure_max = 255,
.debounce_max = 10,
.debounce_tol = 3,
.debounce_rep = 1,
.gpio_pendown = -EINVAL,
.keep_vref_on = 1,
};
static struct spi_board_info ads7846_spi_board_info __initdata = {
.modalias = "ads7846",
.bus_num = -EINVAL,
.chip_select = 0,
.max_speed_hz = 1500000,
.controller_data = &ads7846_mcspi_config,
.irq = -EINVAL,
.platform_data = &ads7846_config,
};
void __init omap_ads7846_init(int bus_num, int gpio_pendown, int gpio_debounce,
struct ads7846_platform_data *board_pdata)
{
struct spi_board_info *spi_bi = &ads7846_spi_board_info;
int err;
if (board_pdata && board_pdata->get_pendown_state) {
err = gpio_request_one(gpio_pendown, GPIOF_IN, "TSPenDown");
if (err) {
pr_err("Couldn't obtain gpio for TSPenDown: %d\n", err);
return;
}
gpio_export(gpio_pendown, 0);
if (gpio_debounce)
gpio_set_debounce(gpio_pendown, gpio_debounce);
}
ads7846_config.gpio_pendown = gpio_pendown;
spi_bi->bus_num = bus_num;
spi_bi->irq = OMAP_GPIO_IRQ(gpio_pendown);
if (board_pdata)
spi_bi->platform_data = board_pdata;
spi_register_board_info(&ads7846_spi_board_info, 1);
}
#else
void __init omap_ads7846_init(int bus_num, int gpio_pendown, int gpio_debounce,
struct ads7846_platform_data *board_pdata)
{
}
#endif
#if defined(CONFIG_MTD_NAND_OMAP2) || defined(CONFIG_MTD_NAND_OMAP2_MODULE)
static struct omap_nand_platform_data nand_data;
void __init omap_nand_flash_init(int options, struct mtd_partition *parts,
int nr_parts)
{
u8 cs = 0;
u8 nandcs = GPMC_CS_NUM + 1;
/* find out the chip-select on which NAND exists */
while (cs < GPMC_CS_NUM) {
u32 ret = 0;
ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
if ((ret & 0xC00) == 0x800) {
printk(KERN_INFO "Found NAND on CS%d\n", cs);
if (nandcs > GPMC_CS_NUM)
nandcs = cs;
}
cs++;
}
if (nandcs > GPMC_CS_NUM) {
printk(KERN_INFO "NAND: Unable to find configuration "
"in GPMC\n ");
return;
}
if (nandcs < GPMC_CS_NUM) {
nand_data.cs = nandcs;
nand_data.parts = parts;
nand_data.nr_parts = nr_parts;
nand_data.devsize = options;
printk(KERN_INFO "Registering NAND on CS%d\n", nandcs);
if (gpmc_nand_init(&nand_data) < 0)
printk(KERN_ERR "Unable to register NAND device\n");
}
}
#else
void __init omap_nand_flash_init(int options, struct mtd_partition *parts,
int nr_parts)
{
}
#endif