video: s3c-fb: Use s3c_fb_enable() to enable the framebuffer
The s3c-fb driver has a function called s3c_fb_enable() which turns on
and off the physical output. However it is only actually used in paths
which disable the screen, the enabling just writes to the register. Make
the code less confusing by ensuring that the enable also goes through
the same path.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
diff --git a/drivers/video/s3c-fb.c b/drivers/video/s3c-fb.c
index b1a75a0..be4c218 100644
--- a/drivers/video/s3c-fb.c
+++ b/drivers/video/s3c-fb.c
@@ -441,6 +441,32 @@
}
/**
+ * s3c_fb_enable() - Set the state of the main LCD output
+ * @sfb: The main framebuffer state.
+ * @enable: The state to set.
+ */
+static void s3c_fb_enable(struct s3c_fb *sfb, int enable)
+{
+ u32 vidcon0 = readl(sfb->regs + VIDCON0);
+
+ if (enable)
+ vidcon0 |= VIDCON0_ENVID | VIDCON0_ENVID_F;
+ else {
+ /* see the note in the framebuffer datasheet about
+ * why you cannot take both of these bits down at the
+ * same time. */
+
+ if (!(vidcon0 & VIDCON0_ENVID))
+ return;
+
+ vidcon0 |= VIDCON0_ENVID;
+ vidcon0 &= ~VIDCON0_ENVID_F;
+ }
+
+ writel(vidcon0, sfb->regs + VIDCON0);
+}
+
+/**
* s3c_fb_set_par() - framebuffer request to set new framebuffer state.
* @info: The framebuffer to change.
*
@@ -510,9 +536,10 @@
if (sfb->variant.is_2443)
data |= (1 << 5);
- data |= VIDCON0_ENVID | VIDCON0_ENVID_F;
writel(data, regs + VIDCON0);
+ s3c_fb_enable(sfb, 1);
+
data = VIDTCON0_VBPD(var->upper_margin - 1) |
VIDTCON0_VFPD(var->lower_margin - 1) |
VIDTCON0_VSPW(var->vsync_len - 1);
@@ -761,32 +788,6 @@
}
/**
- * s3c_fb_enable() - Set the state of the main LCD output
- * @sfb: The main framebuffer state.
- * @enable: The state to set.
- */
-static void s3c_fb_enable(struct s3c_fb *sfb, int enable)
-{
- u32 vidcon0 = readl(sfb->regs + VIDCON0);
-
- if (enable)
- vidcon0 |= VIDCON0_ENVID | VIDCON0_ENVID_F;
- else {
- /* see the note in the framebuffer datasheet about
- * why you cannot take both of these bits down at the
- * same time. */
-
- if (!(vidcon0 & VIDCON0_ENVID))
- return;
-
- vidcon0 |= VIDCON0_ENVID;
- vidcon0 &= ~VIDCON0_ENVID_F;
- }
-
- writel(vidcon0, sfb->regs + VIDCON0);
-}
-
-/**
* s3c_fb_blank() - blank or unblank the given window
* @blank_mode: The blank state from FB_BLANK_*
* @info: The framebuffer to blank.