| /* |
| * jc42.c - driver for Jedec JC42.4 compliant temperature sensors |
| * |
| * Copyright (c) 2010 Ericsson AB. |
| * |
| * Derived from lm77.c by Andras BALI <drewie@freemail.hu>. |
| * |
| * JC42.4 compliant temperature sensors are typically used on memory modules. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/init.h> |
| #include <linux/slab.h> |
| #include <linux/jiffies.h> |
| #include <linux/i2c.h> |
| #include <linux/hwmon.h> |
| #include <linux/hwmon-sysfs.h> |
| #include <linux/err.h> |
| #include <linux/mutex.h> |
| |
| /* Addresses to scan */ |
| static const unsigned short normal_i2c[] = { |
| 0x18, 0x19, 0x1a, 0x1b, 0x1c, 0x1d, 0x1e, 0x1f, I2C_CLIENT_END }; |
| |
| /* JC42 registers. All registers are 16 bit. */ |
| #define JC42_REG_CAP 0x00 |
| #define JC42_REG_CONFIG 0x01 |
| #define JC42_REG_TEMP_UPPER 0x02 |
| #define JC42_REG_TEMP_LOWER 0x03 |
| #define JC42_REG_TEMP_CRITICAL 0x04 |
| #define JC42_REG_TEMP 0x05 |
| #define JC42_REG_MANID 0x06 |
| #define JC42_REG_DEVICEID 0x07 |
| |
| /* Status bits in temperature register */ |
| #define JC42_ALARM_CRIT_BIT 15 |
| #define JC42_ALARM_MAX_BIT 14 |
| #define JC42_ALARM_MIN_BIT 13 |
| |
| /* Configuration register defines */ |
| #define JC42_CFG_CRIT_ONLY (1 << 2) |
| #define JC42_CFG_TCRIT_LOCK (1 << 6) |
| #define JC42_CFG_EVENT_LOCK (1 << 7) |
| #define JC42_CFG_SHUTDOWN (1 << 8) |
| #define JC42_CFG_HYST_SHIFT 9 |
| #define JC42_CFG_HYST_MASK (0x03 << 9) |
| |
| /* Capabilities */ |
| #define JC42_CAP_RANGE (1 << 2) |
| |
| /* Manufacturer IDs */ |
| #define ADT_MANID 0x11d4 /* Analog Devices */ |
| #define ATMEL_MANID 0x001f /* Atmel */ |
| #define ATMEL_MANID2 0x1114 /* Atmel */ |
| #define MAX_MANID 0x004d /* Maxim */ |
| #define IDT_MANID 0x00b3 /* IDT */ |
| #define MCP_MANID 0x0054 /* Microchip */ |
| #define NXP_MANID 0x1131 /* NXP Semiconductors */ |
| #define ONS_MANID 0x1b09 /* ON Semiconductor */ |
| #define STM_MANID 0x104a /* ST Microelectronics */ |
| |
| /* Supported chips */ |
| |
| /* Analog Devices */ |
| #define ADT7408_DEVID 0x0801 |
| #define ADT7408_DEVID_MASK 0xffff |
| |
| /* Atmel */ |
| #define AT30TS00_DEVID 0x8201 |
| #define AT30TS00_DEVID_MASK 0xffff |
| |
| #define AT30TSE004_DEVID 0x2200 |
| #define AT30TSE004_DEVID_MASK 0xffff |
| |
| /* IDT */ |
| #define TSE2004_DEVID 0x2200 |
| #define TSE2004_DEVID_MASK 0xff00 |
| |
| #define TS3000_DEVID 0x2900 /* Also matches TSE2002 */ |
| #define TS3000_DEVID_MASK 0xff00 |
| |
| #define TS3001_DEVID 0x3000 |
| #define TS3001_DEVID_MASK 0xff00 |
| |
| /* Maxim */ |
| #define MAX6604_DEVID 0x3e00 |
| #define MAX6604_DEVID_MASK 0xffff |
| |
| /* Microchip */ |
| #define MCP9804_DEVID 0x0200 |
| #define MCP9804_DEVID_MASK 0xfffc |
| |
| #define MCP9808_DEVID 0x0400 |
| #define MCP9808_DEVID_MASK 0xfffc |
| |
| #define MCP98242_DEVID 0x2000 |
| #define MCP98242_DEVID_MASK 0xfffc |
| |
| #define MCP98243_DEVID 0x2100 |
| #define MCP98243_DEVID_MASK 0xfffc |
| |
| #define MCP98244_DEVID 0x2200 |
| #define MCP98244_DEVID_MASK 0xfffc |
| |
| #define MCP9843_DEVID 0x0000 /* Also matches mcp9805 */ |
| #define MCP9843_DEVID_MASK 0xfffe |
| |
| /* NXP */ |
| #define SE97_DEVID 0xa200 |
| #define SE97_DEVID_MASK 0xfffc |
| |
| #define SE98_DEVID 0xa100 |
| #define SE98_DEVID_MASK 0xfffc |
| |
| /* ON Semiconductor */ |
| #define CAT6095_DEVID 0x0800 /* Also matches CAT34TS02 */ |
| #define CAT6095_DEVID_MASK 0xffe0 |
| |
| /* ST Microelectronics */ |
| #define STTS424_DEVID 0x0101 |
| #define STTS424_DEVID_MASK 0xffff |
| |
| #define STTS424E_DEVID 0x0000 |
| #define STTS424E_DEVID_MASK 0xfffe |
| |
| #define STTS2002_DEVID 0x0300 |
| #define STTS2002_DEVID_MASK 0xffff |
| |
| #define STTS2004_DEVID 0x2201 |
| #define STTS2004_DEVID_MASK 0xffff |
| |
| #define STTS3000_DEVID 0x0200 |
| #define STTS3000_DEVID_MASK 0xffff |
| |
| static u16 jc42_hysteresis[] = { 0, 1500, 3000, 6000 }; |
| |
| struct jc42_chips { |
| u16 manid; |
| u16 devid; |
| u16 devid_mask; |
| }; |
| |
| static struct jc42_chips jc42_chips[] = { |
| { ADT_MANID, ADT7408_DEVID, ADT7408_DEVID_MASK }, |
| { ATMEL_MANID, AT30TS00_DEVID, AT30TS00_DEVID_MASK }, |
| { ATMEL_MANID2, AT30TSE004_DEVID, AT30TSE004_DEVID_MASK }, |
| { IDT_MANID, TSE2004_DEVID, TSE2004_DEVID_MASK }, |
| { IDT_MANID, TS3000_DEVID, TS3000_DEVID_MASK }, |
| { IDT_MANID, TS3001_DEVID, TS3001_DEVID_MASK }, |
| { MAX_MANID, MAX6604_DEVID, MAX6604_DEVID_MASK }, |
| { MCP_MANID, MCP9804_DEVID, MCP9804_DEVID_MASK }, |
| { MCP_MANID, MCP9808_DEVID, MCP9808_DEVID_MASK }, |
| { MCP_MANID, MCP98242_DEVID, MCP98242_DEVID_MASK }, |
| { MCP_MANID, MCP98243_DEVID, MCP98243_DEVID_MASK }, |
| { MCP_MANID, MCP98244_DEVID, MCP98244_DEVID_MASK }, |
| { MCP_MANID, MCP9843_DEVID, MCP9843_DEVID_MASK }, |
| { NXP_MANID, SE97_DEVID, SE97_DEVID_MASK }, |
| { ONS_MANID, CAT6095_DEVID, CAT6095_DEVID_MASK }, |
| { NXP_MANID, SE98_DEVID, SE98_DEVID_MASK }, |
| { STM_MANID, STTS424_DEVID, STTS424_DEVID_MASK }, |
| { STM_MANID, STTS424E_DEVID, STTS424E_DEVID_MASK }, |
| { STM_MANID, STTS2002_DEVID, STTS2002_DEVID_MASK }, |
| { STM_MANID, STTS2004_DEVID, STTS2004_DEVID_MASK }, |
| { STM_MANID, STTS3000_DEVID, STTS3000_DEVID_MASK }, |
| }; |
| |
| enum temp_index { |
| t_input = 0, |
| t_crit, |
| t_min, |
| t_max, |
| t_num_temp |
| }; |
| |
| static const u8 temp_regs[t_num_temp] = { |
| [t_input] = JC42_REG_TEMP, |
| [t_crit] = JC42_REG_TEMP_CRITICAL, |
| [t_min] = JC42_REG_TEMP_LOWER, |
| [t_max] = JC42_REG_TEMP_UPPER, |
| }; |
| |
| /* Each client has this additional data */ |
| struct jc42_data { |
| struct i2c_client *client; |
| struct mutex update_lock; /* protect register access */ |
| bool extended; /* true if extended range supported */ |
| bool valid; |
| unsigned long last_updated; /* In jiffies */ |
| u16 orig_config; /* original configuration */ |
| u16 config; /* current configuration */ |
| u16 temp[t_num_temp];/* Temperatures */ |
| }; |
| |
| #define JC42_TEMP_MIN_EXTENDED (-40000) |
| #define JC42_TEMP_MIN 0 |
| #define JC42_TEMP_MAX 125000 |
| |
| static u16 jc42_temp_to_reg(long temp, bool extended) |
| { |
| int ntemp = clamp_val(temp, |
| extended ? JC42_TEMP_MIN_EXTENDED : |
| JC42_TEMP_MIN, JC42_TEMP_MAX); |
| |
| /* convert from 0.001 to 0.0625 resolution */ |
| return (ntemp * 2 / 125) & 0x1fff; |
| } |
| |
| static int jc42_temp_from_reg(s16 reg) |
| { |
| reg = sign_extend32(reg, 12); |
| |
| /* convert from 0.0625 to 0.001 resolution */ |
| return reg * 125 / 2; |
| } |
| |
| static struct jc42_data *jc42_update_device(struct device *dev) |
| { |
| struct jc42_data *data = dev_get_drvdata(dev); |
| struct i2c_client *client = data->client; |
| struct jc42_data *ret = data; |
| int i, val; |
| |
| mutex_lock(&data->update_lock); |
| |
| if (time_after(jiffies, data->last_updated + HZ) || !data->valid) { |
| for (i = 0; i < t_num_temp; i++) { |
| val = i2c_smbus_read_word_swapped(client, temp_regs[i]); |
| if (val < 0) { |
| ret = ERR_PTR(val); |
| goto abort; |
| } |
| data->temp[i] = val; |
| } |
| data->last_updated = jiffies; |
| data->valid = true; |
| } |
| abort: |
| mutex_unlock(&data->update_lock); |
| return ret; |
| } |
| |
| /* sysfs functions */ |
| |
| static ssize_t show_temp(struct device *dev, struct device_attribute *devattr, |
| char *buf) |
| { |
| struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); |
| struct jc42_data *data = jc42_update_device(dev); |
| if (IS_ERR(data)) |
| return PTR_ERR(data); |
| return sprintf(buf, "%d\n", |
| jc42_temp_from_reg(data->temp[attr->index])); |
| } |
| |
| static ssize_t show_temp_hyst(struct device *dev, |
| struct device_attribute *devattr, char *buf) |
| { |
| struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); |
| struct jc42_data *data = jc42_update_device(dev); |
| int temp, hyst; |
| |
| if (IS_ERR(data)) |
| return PTR_ERR(data); |
| |
| temp = jc42_temp_from_reg(data->temp[attr->index]); |
| hyst = jc42_hysteresis[(data->config & JC42_CFG_HYST_MASK) |
| >> JC42_CFG_HYST_SHIFT]; |
| return sprintf(buf, "%d\n", temp - hyst); |
| } |
| |
| static ssize_t set_temp(struct device *dev, struct device_attribute *devattr, |
| const char *buf, size_t count) |
| { |
| struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); |
| struct jc42_data *data = dev_get_drvdata(dev); |
| int err, ret = count; |
| int nr = attr->index; |
| long val; |
| |
| if (kstrtol(buf, 10, &val) < 0) |
| return -EINVAL; |
| mutex_lock(&data->update_lock); |
| data->temp[nr] = jc42_temp_to_reg(val, data->extended); |
| err = i2c_smbus_write_word_swapped(data->client, temp_regs[nr], |
| data->temp[nr]); |
| if (err < 0) |
| ret = err; |
| mutex_unlock(&data->update_lock); |
| return ret; |
| } |
| |
| /* |
| * JC42.4 compliant chips only support four hysteresis values. |
| * Pick best choice and go from there. |
| */ |
| static ssize_t set_temp_crit_hyst(struct device *dev, |
| struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct jc42_data *data = dev_get_drvdata(dev); |
| long val; |
| int diff, hyst; |
| int err; |
| int ret = count; |
| |
| if (kstrtol(buf, 10, &val) < 0) |
| return -EINVAL; |
| |
| val = clamp_val(val, (data->extended ? JC42_TEMP_MIN_EXTENDED : |
| JC42_TEMP_MIN) - 6000, JC42_TEMP_MAX); |
| diff = jc42_temp_from_reg(data->temp[t_crit]) - val; |
| |
| hyst = 0; |
| if (diff > 0) { |
| if (diff < 2250) |
| hyst = 1; /* 1.5 degrees C */ |
| else if (diff < 4500) |
| hyst = 2; /* 3.0 degrees C */ |
| else |
| hyst = 3; /* 6.0 degrees C */ |
| } |
| |
| mutex_lock(&data->update_lock); |
| data->config = (data->config & ~JC42_CFG_HYST_MASK) |
| | (hyst << JC42_CFG_HYST_SHIFT); |
| err = i2c_smbus_write_word_swapped(data->client, JC42_REG_CONFIG, |
| data->config); |
| if (err < 0) |
| ret = err; |
| mutex_unlock(&data->update_lock); |
| return ret; |
| } |
| |
| static ssize_t show_alarm(struct device *dev, |
| struct device_attribute *attr, char *buf) |
| { |
| u16 bit = to_sensor_dev_attr(attr)->index; |
| struct jc42_data *data = jc42_update_device(dev); |
| u16 val; |
| |
| if (IS_ERR(data)) |
| return PTR_ERR(data); |
| |
| val = data->temp[t_input]; |
| if (bit != JC42_ALARM_CRIT_BIT && (data->config & JC42_CFG_CRIT_ONLY)) |
| val = 0; |
| return sprintf(buf, "%u\n", (val >> bit) & 1); |
| } |
| |
| static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp, NULL, t_input); |
| static SENSOR_DEVICE_ATTR(temp1_crit, S_IRUGO, show_temp, set_temp, t_crit); |
| static SENSOR_DEVICE_ATTR(temp1_min, S_IRUGO, show_temp, set_temp, t_min); |
| static SENSOR_DEVICE_ATTR(temp1_max, S_IRUGO, show_temp, set_temp, t_max); |
| |
| static SENSOR_DEVICE_ATTR(temp1_crit_hyst, S_IRUGO, show_temp_hyst, |
| set_temp_crit_hyst, t_crit); |
| static SENSOR_DEVICE_ATTR(temp1_max_hyst, S_IRUGO, show_temp_hyst, NULL, t_max); |
| |
| static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL, |
| JC42_ALARM_CRIT_BIT); |
| static SENSOR_DEVICE_ATTR(temp1_min_alarm, S_IRUGO, show_alarm, NULL, |
| JC42_ALARM_MIN_BIT); |
| static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL, |
| JC42_ALARM_MAX_BIT); |
| |
| static struct attribute *jc42_attributes[] = { |
| &sensor_dev_attr_temp1_input.dev_attr.attr, |
| &sensor_dev_attr_temp1_crit.dev_attr.attr, |
| &sensor_dev_attr_temp1_min.dev_attr.attr, |
| &sensor_dev_attr_temp1_max.dev_attr.attr, |
| &sensor_dev_attr_temp1_crit_hyst.dev_attr.attr, |
| &sensor_dev_attr_temp1_max_hyst.dev_attr.attr, |
| &sensor_dev_attr_temp1_crit_alarm.dev_attr.attr, |
| &sensor_dev_attr_temp1_min_alarm.dev_attr.attr, |
| &sensor_dev_attr_temp1_max_alarm.dev_attr.attr, |
| NULL |
| }; |
| |
| static umode_t jc42_attribute_mode(struct kobject *kobj, |
| struct attribute *attr, int index) |
| { |
| struct device *dev = container_of(kobj, struct device, kobj); |
| struct jc42_data *data = dev_get_drvdata(dev); |
| unsigned int config = data->config; |
| bool readonly; |
| |
| if (attr == &sensor_dev_attr_temp1_crit.dev_attr.attr) |
| readonly = config & JC42_CFG_TCRIT_LOCK; |
| else if (attr == &sensor_dev_attr_temp1_min.dev_attr.attr || |
| attr == &sensor_dev_attr_temp1_max.dev_attr.attr) |
| readonly = config & JC42_CFG_EVENT_LOCK; |
| else if (attr == &sensor_dev_attr_temp1_crit_hyst.dev_attr.attr) |
| readonly = config & (JC42_CFG_EVENT_LOCK | JC42_CFG_TCRIT_LOCK); |
| else |
| readonly = true; |
| |
| return S_IRUGO | (readonly ? 0 : S_IWUSR); |
| } |
| |
| static const struct attribute_group jc42_group = { |
| .attrs = jc42_attributes, |
| .is_visible = jc42_attribute_mode, |
| }; |
| __ATTRIBUTE_GROUPS(jc42); |
| |
| /* Return 0 if detection is successful, -ENODEV otherwise */ |
| static int jc42_detect(struct i2c_client *client, struct i2c_board_info *info) |
| { |
| struct i2c_adapter *adapter = client->adapter; |
| int i, config, cap, manid, devid; |
| |
| if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA | |
| I2C_FUNC_SMBUS_WORD_DATA)) |
| return -ENODEV; |
| |
| cap = i2c_smbus_read_word_swapped(client, JC42_REG_CAP); |
| config = i2c_smbus_read_word_swapped(client, JC42_REG_CONFIG); |
| manid = i2c_smbus_read_word_swapped(client, JC42_REG_MANID); |
| devid = i2c_smbus_read_word_swapped(client, JC42_REG_DEVICEID); |
| |
| if (cap < 0 || config < 0 || manid < 0 || devid < 0) |
| return -ENODEV; |
| |
| if ((cap & 0xff00) || (config & 0xf800)) |
| return -ENODEV; |
| |
| for (i = 0; i < ARRAY_SIZE(jc42_chips); i++) { |
| struct jc42_chips *chip = &jc42_chips[i]; |
| if (manid == chip->manid && |
| (devid & chip->devid_mask) == chip->devid) { |
| strlcpy(info->type, "jc42", I2C_NAME_SIZE); |
| return 0; |
| } |
| } |
| return -ENODEV; |
| } |
| |
| static int jc42_probe(struct i2c_client *client, const struct i2c_device_id *id) |
| { |
| struct device *dev = &client->dev; |
| struct device *hwmon_dev; |
| struct jc42_data *data; |
| int config, cap; |
| |
| data = devm_kzalloc(dev, sizeof(struct jc42_data), GFP_KERNEL); |
| if (!data) |
| return -ENOMEM; |
| |
| data->client = client; |
| i2c_set_clientdata(client, data); |
| mutex_init(&data->update_lock); |
| |
| cap = i2c_smbus_read_word_swapped(client, JC42_REG_CAP); |
| if (cap < 0) |
| return cap; |
| |
| data->extended = !!(cap & JC42_CAP_RANGE); |
| |
| config = i2c_smbus_read_word_swapped(client, JC42_REG_CONFIG); |
| if (config < 0) |
| return config; |
| |
| data->orig_config = config; |
| if (config & JC42_CFG_SHUTDOWN) { |
| config &= ~JC42_CFG_SHUTDOWN; |
| i2c_smbus_write_word_swapped(client, JC42_REG_CONFIG, config); |
| } |
| data->config = config; |
| |
| hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name, |
| data, |
| jc42_groups); |
| return PTR_ERR_OR_ZERO(hwmon_dev); |
| } |
| |
| static int jc42_remove(struct i2c_client *client) |
| { |
| struct jc42_data *data = i2c_get_clientdata(client); |
| |
| /* Restore original configuration except hysteresis */ |
| if ((data->config & ~JC42_CFG_HYST_MASK) != |
| (data->orig_config & ~JC42_CFG_HYST_MASK)) { |
| int config; |
| |
| config = (data->orig_config & ~JC42_CFG_HYST_MASK) |
| | (data->config & JC42_CFG_HYST_MASK); |
| i2c_smbus_write_word_swapped(client, JC42_REG_CONFIG, config); |
| } |
| return 0; |
| } |
| |
| #ifdef CONFIG_PM |
| |
| static int jc42_suspend(struct device *dev) |
| { |
| struct jc42_data *data = dev_get_drvdata(dev); |
| |
| data->config |= JC42_CFG_SHUTDOWN; |
| i2c_smbus_write_word_swapped(data->client, JC42_REG_CONFIG, |
| data->config); |
| return 0; |
| } |
| |
| static int jc42_resume(struct device *dev) |
| { |
| struct jc42_data *data = dev_get_drvdata(dev); |
| |
| data->config &= ~JC42_CFG_SHUTDOWN; |
| i2c_smbus_write_word_swapped(data->client, JC42_REG_CONFIG, |
| data->config); |
| return 0; |
| } |
| |
| static const struct dev_pm_ops jc42_dev_pm_ops = { |
| .suspend = jc42_suspend, |
| .resume = jc42_resume, |
| }; |
| |
| #define JC42_DEV_PM_OPS (&jc42_dev_pm_ops) |
| #else |
| #define JC42_DEV_PM_OPS NULL |
| #endif /* CONFIG_PM */ |
| |
| static const struct i2c_device_id jc42_id[] = { |
| { "jc42", 0 }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(i2c, jc42_id); |
| |
| static struct i2c_driver jc42_driver = { |
| .class = I2C_CLASS_SPD, |
| .driver = { |
| .name = "jc42", |
| .pm = JC42_DEV_PM_OPS, |
| }, |
| .probe = jc42_probe, |
| .remove = jc42_remove, |
| .id_table = jc42_id, |
| .detect = jc42_detect, |
| .address_list = normal_i2c, |
| }; |
| |
| module_i2c_driver(jc42_driver); |
| |
| MODULE_AUTHOR("Guenter Roeck <linux@roeck-us.net>"); |
| MODULE_DESCRIPTION("JC42 driver"); |
| MODULE_LICENSE("GPL"); |