| These properties are common to multiple MMC host controllers. Any host |
| that requires the respective functionality should implement them using |
| these definitions. |
| |
| Interpreted by the OF core: |
| - reg: Registers location and length. |
| - interrupts: Interrupts used by the MMC controller. |
| |
| Card detection: |
| If no property below is supplied, host native card detect is used. |
| Only one of the properties in this section should be supplied: |
| - broken-cd: There is no card detection available; polling must be used. |
| - cd-gpios: Specify GPIOs for card detection, see gpio binding |
| - non-removable: non-removable slot (like eMMC); assume always present. |
| |
| Optional properties: |
| - bus-width: Number of data lines, can be <1>, <4>, or <8>. The default |
| will be <1> if the property is absent. |
| - wp-gpios: Specify GPIOs for write protection, see gpio binding |
| - cd-inverted: when present, polarity on the CD line is inverted. See the note |
| below for the case, when a GPIO is used for the CD line |
| - wp-inverted: when present, polarity on the WP line is inverted. See the note |
| below for the case, when a GPIO is used for the WP line |
| - max-frequency: maximum operating clock frequency |
| - no-1-8-v: when present, denotes that 1.8v card voltage is not supported on |
| this system, even if the controller claims it is. |
| - cap-sd-highspeed: SD high-speed timing is supported |
| - cap-mmc-highspeed: MMC high-speed timing is supported |
| - sd-uhs-sdr12: SD UHS SDR12 speed is supported |
| - sd-uhs-sdr25: SD UHS SDR25 speed is supported |
| - sd-uhs-sdr50: SD UHS SDR50 speed is supported |
| - sd-uhs-sdr104: SD UHS SDR104 speed is supported |
| - sd-uhs-ddr50: SD UHS DDR50 speed is supported |
| - cap-power-off-card: powering off the card is safe |
| - cap-sdio-irq: enable SDIO IRQ signalling on this interface |
| - full-pwr-cycle: full power cycle of the card is supported |
| - mmc-ddr-1_8v: eMMC high-speed DDR mode(1.8V I/O) is supported |
| - mmc-ddr-1_2v: eMMC high-speed DDR mode(1.2V I/O) is supported |
| - mmc-hs200-1_8v: eMMC HS200 mode(1.8V I/O) is supported |
| - mmc-hs200-1_2v: eMMC HS200 mode(1.2V I/O) is supported |
| - mmc-hs400-1_8v: eMMC HS400 mode(1.8V I/O) is supported |
| - mmc-hs400-1_2v: eMMC HS400 mode(1.2V I/O) is supported |
| - dsr: Value the card's (optional) Driver Stage Register (DSR) should be |
| programmed with. Valid range: [0 .. 0xffff]. |
| |
| *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line |
| polarity properties, we have to fix the meaning of the "normal" and "inverted" |
| line levels. We choose to follow the SDHCI standard, which specifies both those |
| lines as "active low." Therefore, using the "cd-inverted" property means, that |
| the CD line is active high, i.e. it is high, when a card is inserted. Similar |
| logic applies to the "wp-inverted" property. |
| |
| CD and WP lines can be implemented on the hardware in one of two ways: as GPIOs, |
| specified in cd-gpios and wp-gpios properties, or as dedicated pins. Polarity of |
| dedicated pins can be specified, using *-inverted properties. GPIO polarity can |
| also be specified using the OF_GPIO_ACTIVE_LOW flag. This creates an ambiguity |
| in the latter case. We choose to use the XOR logic for GPIO CD and WP lines. |
| This means, the two properties are "superimposed," for example leaving the |
| OF_GPIO_ACTIVE_LOW flag clear and specifying the respective *-inverted |
| property results in a double-inversion and actually means the "normal" line |
| polarity is in effect. |
| |
| Optional SDIO properties: |
| - keep-power-in-suspend: Preserves card power during a suspend/resume cycle |
| - enable-sdio-wakeup: Enables wake up of host system on SDIO IRQ assertion |
| |
| |
| Use of Function subnodes |
| ------------------------ |
| |
| On embedded systems the cards connected to a host may need additional |
| properties. These can be specified in subnodes to the host controller node. |
| The subnodes are identified by the standard 'reg' property. |
| Which information exactly can be specified depends on the bindings for the |
| SDIO function driver for the subnode, as specified by the compatible string. |
| |
| Required host node properties when using function subnodes: |
| - #address-cells: should be one. The cell is the slot id. |
| - #size-cells: should be zero. |
| |
| Required function subnode properties: |
| - compatible: name of SDIO function following generic names recommended practice |
| - reg: Must contain the SDIO function number of the function this subnode |
| describes. A value of 0 denotes the memory SD function, values from |
| 1 to 7 denote the SDIO functions. |
| |
| |
| Examples |
| -------- |
| |
| Basic example: |
| |
| sdhci@ab000000 { |
| compatible = "sdhci"; |
| reg = <0xab000000 0x200>; |
| interrupts = <23>; |
| bus-width = <4>; |
| cd-gpios = <&gpio 69 0>; |
| cd-inverted; |
| wp-gpios = <&gpio 70 0>; |
| max-frequency = <50000000>; |
| keep-power-in-suspend; |
| enable-sdio-wakeup; |
| } |
| |
| Example with sdio function subnode: |
| |
| mmc3: mmc@01c12000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc3_pins_a>; |
| vmmc-supply = <®_vmmc3>; |
| bus-width = <4>; |
| non-removable; |
| status = "okay"; |
| |
| brcmf: bcrmf@1 { |
| reg = <1>; |
| compatible = "brcm,bcm43xx-fmac"; |
| interrupt-parent = <&pio>; |
| interrupts = <10 8>; /* PH10 / EINT10 */ |
| interrupt-names = "host-wake"; |
| }; |
| }; |