mmc: replace printk with appropriate display macro
All the files using printk function for displaying kernel messages
in the mmc driver have been replaced with corresponding macro.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
index 7dde373..4e869d3 100644
--- a/drivers/mmc/core/mmc.c
+++ b/drivers/mmc/core/mmc.c
@@ -101,7 +101,7 @@
break;
default:
- printk(KERN_ERR "%s: card has unknown MMCA version %d\n",
+ pr_err("%s: card has unknown MMCA version %d\n",
mmc_hostname(card->host), card->csd.mmca_vsn);
return -EINVAL;
}
@@ -135,7 +135,7 @@
*/
csd->structure = UNSTUFF_BITS(resp, 126, 2);
if (csd->structure == 0) {
- printk(KERN_ERR "%s: unrecognised CSD structure version %d\n",
+ pr_err("%s: unrecognised CSD structure version %d\n",
mmc_hostname(card->host), csd->structure);
return -EINVAL;
}
@@ -195,7 +195,7 @@
*/
ext_csd = kmalloc(512, GFP_KERNEL);
if (!ext_csd) {
- printk(KERN_ERR "%s: could not allocate a buffer to "
+ pr_err("%s: could not allocate a buffer to "
"receive the ext_csd.\n", mmc_hostname(card->host));
return -ENOMEM;
}
@@ -217,12 +217,12 @@
* stored in their CSD.
*/
if (card->csd.capacity == (4096 * 512)) {
- printk(KERN_ERR "%s: unable to read EXT_CSD "
+ pr_err("%s: unable to read EXT_CSD "
"on a possible high capacity card. "
"Card will be ignored.\n",
mmc_hostname(card->host));
} else {
- printk(KERN_WARNING "%s: unable to read "
+ pr_warning("%s: unable to read "
"EXT_CSD, performance might "
"suffer.\n",
mmc_hostname(card->host));
@@ -252,7 +252,7 @@
card->ext_csd.raw_ext_csd_structure = ext_csd[EXT_CSD_STRUCTURE];
if (card->csd.structure == 3) {
if (card->ext_csd.raw_ext_csd_structure > 2) {
- printk(KERN_ERR "%s: unrecognised EXT_CSD structure "
+ pr_err("%s: unrecognised EXT_CSD structure "
"version %d\n", mmc_hostname(card->host),
card->ext_csd.raw_ext_csd_structure);
err = -EINVAL;
@@ -262,7 +262,7 @@
card->ext_csd.rev = ext_csd[EXT_CSD_REV];
if (card->ext_csd.rev > 6) {
- printk(KERN_ERR "%s: unrecognised EXT_CSD revision %d\n",
+ pr_err("%s: unrecognised EXT_CSD revision %d\n",
mmc_hostname(card->host), card->ext_csd.rev);
err = -EINVAL;
goto out;
@@ -308,7 +308,7 @@
break;
default:
/* MMC v4 spec says this cannot happen */
- printk(KERN_WARNING "%s: card is mmc v4 but doesn't "
+ pr_warning("%s: card is mmc v4 but doesn't "
"support any high-speed modes.\n",
mmc_hostname(card->host));
}
@@ -857,7 +857,7 @@
goto free_card;
if (err) {
- printk(KERN_WARNING "%s: switch to highspeed failed\n",
+ pr_warning("%s: switch to highspeed failed\n",
mmc_hostname(card->host));
err = 0;
} else {
@@ -966,7 +966,7 @@
card->ext_csd.generic_cmd6_time);
}
if (err) {
- printk(KERN_WARNING "%s: switch to bus width %d ddr %d "
+ pr_warning("%s: switch to bus width %d ddr %d "
"failed\n", mmc_hostname(card->host),
1 << bus_width, ddr);
goto free_card;
@@ -1204,7 +1204,7 @@
* support.
*/
if (ocr & 0x7F) {
- printk(KERN_WARNING "%s: card claims to support voltages "
+ pr_warning("%s: card claims to support voltages "
"below the defined range. These will be ignored.\n",
mmc_hostname(host));
ocr &= ~0x7F;
@@ -1243,7 +1243,7 @@
err:
mmc_detach_bus(host);
- printk(KERN_ERR "%s: error %d whilst initialising MMC card\n",
+ pr_err("%s: error %d whilst initialising MMC card\n",
mmc_hostname(host), err);
return err;