| /* |
| * This file is licensed under the terms of the GNU General Public License |
| * version 2. This program is licensed "as is" without any warranty of any |
| * kind, whether express or implied. |
| */ |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/pinctrl/omap.h> |
| |
| #include "skeleton.dtsi" |
| |
| / { |
| compatible = "ti,dm814"; |
| interrupt-parent = <&intc>; |
| |
| aliases { |
| i2c0 = &i2c1; |
| i2c1 = &i2c2; |
| serial0 = &uart1; |
| serial1 = &uart2; |
| serial2 = &uart3; |
| ethernet0 = &cpsw_emac0; |
| ethernet1 = &cpsw_emac1; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| cpu@0 { |
| compatible = "arm,cortex-a8"; |
| device_type = "cpu"; |
| reg = <0>; |
| }; |
| }; |
| |
| pmu { |
| compatible = "arm,cortex-a8-pmu"; |
| interrupts = <3>; |
| }; |
| |
| /* |
| * The soc node represents the soc top level view. It is used for IPs |
| * that are not memory mapped in the MPU view or for the MPU itself. |
| */ |
| soc { |
| compatible = "ti,omap-infra"; |
| mpu { |
| compatible = "ti,omap3-mpu"; |
| ti,hwmods = "mpu"; |
| }; |
| }; |
| |
| ocp { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| ti,hwmods = "l3_main"; |
| |
| /* |
| * See TRM "Table 1-317. L4LS Instance Summary", just deduct |
| * 0x1000 from the 1-317 addresses to get the device address |
| */ |
| l4ls: l4ls@48000000 { |
| compatible = "ti,dm814-l4ls", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x48000000 0x2000000>; |
| |
| i2c1: i2c@28000 { |
| compatible = "ti,omap4-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "i2c1"; |
| reg = <0x28000 0x1000>; |
| interrupts = <70>; |
| }; |
| |
| elm: elm@80000 { |
| compatible = "ti,814-elm"; |
| ti,hwmods = "elm"; |
| reg = <0x80000 0x2000>; |
| interrupts = <4>; |
| }; |
| |
| gpio1: gpio@32000 { |
| compatible = "ti,omap4-gpio"; |
| ti,hwmods = "gpio1"; |
| ti,gpio-always-on; |
| reg = <0x32000 0x2000>; |
| interrupts = <96>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio2: gpio@4c000 { |
| compatible = "ti,omap4-gpio"; |
| ti,hwmods = "gpio2"; |
| ti,gpio-always-on; |
| reg = <0x4c000 0x2000>; |
| interrupts = <98>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| i2c2: i2c@2a000 { |
| compatible = "ti,omap4-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "i2c2"; |
| reg = <0x2a000 0x1000>; |
| interrupts = <71>; |
| }; |
| |
| mcspi1: spi@30000 { |
| compatible = "ti,omap4-mcspi"; |
| reg = <0x30000 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <65>; |
| ti,spi-num-cs = <4>; |
| ti,hwmods = "mcspi1"; |
| dmas = <&edma 16 &edma 17 |
| &edma 18 &edma 19>; |
| dma-names = "tx0", "rx0", "tx1", "rx1"; |
| }; |
| |
| timer1: timer@2e000 { |
| compatible = "ti,dm814-timer"; |
| reg = <0x2e000 0x2000>; |
| interrupts = <67>; |
| ti,hwmods = "timer1"; |
| ti,timer-alwon; |
| }; |
| |
| uart1: uart@20000 { |
| compatible = "ti,omap3-uart"; |
| ti,hwmods = "uart1"; |
| reg = <0x20000 0x2000>; |
| clock-frequency = <48000000>; |
| interrupts = <72>; |
| dmas = <&edma 26 &edma 27>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| uart2: uart@22000 { |
| compatible = "ti,omap3-uart"; |
| ti,hwmods = "uart2"; |
| reg = <0x22000 0x2000>; |
| clock-frequency = <48000000>; |
| interrupts = <73>; |
| dmas = <&edma 28 &edma 29>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| uart3: uart@24000 { |
| compatible = "ti,omap3-uart"; |
| ti,hwmods = "uart3"; |
| reg = <0x24000 0x2000>; |
| clock-frequency = <48000000>; |
| interrupts = <74>; |
| dmas = <&edma 30 &edma 31>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| timer2: timer@40000 { |
| compatible = "ti,dm814-timer"; |
| reg = <0x40000 0x2000>; |
| interrupts = <68>; |
| ti,hwmods = "timer2"; |
| }; |
| |
| timer3: timer@42000 { |
| compatible = "ti,dm814-timer"; |
| reg = <0x42000 0x2000>; |
| interrupts = <69>; |
| ti,hwmods = "timer3"; |
| }; |
| |
| control: control@160000 { |
| compatible = "ti,dm814-scm", "simple-bus"; |
| reg = <0x160000 0x16d000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x160000 0x16d000>; |
| |
| scm_conf: scm_conf@0 { |
| compatible = "syscon"; |
| reg = <0x0 0x800>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| scm_clocks: clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| scm_clockdomains: clockdomains { |
| }; |
| }; |
| |
| pincntl: pinmux@800 { |
| compatible = "pinctrl-single"; |
| reg = <0x800 0xc38>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| pinctrl-single,register-width = <32>; |
| pinctrl-single,function-mask = <0x300ff>; |
| }; |
| }; |
| |
| prcm: prcm@180000 { |
| compatible = "ti,dm814-prcm", "simple-bus"; |
| reg = <0x180000 0x4000>; |
| |
| prcm_clocks: clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| prcm_clockdomains: clockdomains { |
| }; |
| }; |
| |
| pllss: pllss@1c5000 { |
| compatible = "ti,dm814-pllss", "simple-bus"; |
| reg = <0x1c5000 0x2000>; |
| |
| pllss_clocks: clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| pllss_clockdomains: clockdomains { |
| }; |
| }; |
| |
| wdt1: wdt@1c7000 { |
| compatible = "ti,omap3-wdt"; |
| ti,hwmods = "wd_timer"; |
| reg = <0x1c7000 0x1000>; |
| interrupts = <91>; |
| }; |
| }; |
| |
| intc: interrupt-controller@48200000 { |
| compatible = "ti,dm814-intc"; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| reg = <0x48200000 0x1000>; |
| }; |
| |
| edma: edma@49000000 { |
| compatible = "ti,edma3"; |
| ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2"; |
| reg = <0x49000000 0x10000>, |
| <0x44e10f90 0x40>; |
| interrupts = <12 13 14>; |
| #dma-cells = <1>; |
| }; |
| |
| /* See TRM "Table 1-318. L4HS Instance Summary" */ |
| l4hs: l4hs@4a000000 { |
| compatible = "ti,dm814-l4hs", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x4a000000 0x1b4040>; |
| }; |
| |
| /* REVISIT: Move to live under l4hs once driver is fixed */ |
| mac: ethernet@4a100000 { |
| compatible = "ti,cpsw"; |
| ti,hwmods = "cpgmac0"; |
| clocks = <&cpsw_125mhz_gclk>, <&cpsw_cpts_rft_clk>; |
| clock-names = "fck", "cpts"; |
| cpdma_channels = <8>; |
| ale_entries = <1024>; |
| bd_ram_size = <0x2000>; |
| no_bd_ram = <0>; |
| rx_descs = <64>; |
| mac_control = <0x20>; |
| slaves = <2>; |
| active_slave = <0>; |
| cpts_clock_mult = <0x80000000>; |
| cpts_clock_shift = <29>; |
| reg = <0x4a100000 0x800 |
| 0x4a100900 0x100>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| interrupt-parent = <&intc>; |
| /* |
| * c0_rx_thresh_pend |
| * c0_rx_pend |
| * c0_tx_pend |
| * c0_misc_pend |
| */ |
| interrupts = <40 41 42 43>; |
| ranges; |
| syscon = <&scm_conf>; |
| |
| davinci_mdio: mdio@4a100800 { |
| compatible = "ti,davinci_mdio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "davinci_mdio"; |
| bus_freq = <1000000>; |
| reg = <0x4a100800 0x100>; |
| }; |
| |
| cpsw_emac0: slave@4a100200 { |
| /* Filled in by U-Boot */ |
| mac-address = [ 00 00 00 00 00 00 ]; |
| }; |
| |
| cpsw_emac1: slave@4a100300 { |
| /* Filled in by U-Boot */ |
| mac-address = [ 00 00 00 00 00 00 ]; |
| }; |
| |
| phy_sel: cpsw-phy-sel@0x48160650 { |
| compatible = "ti,am3352-cpsw-phy-sel"; |
| reg= <0x48160650 0x4>; |
| reg-names = "gmii-sel"; |
| }; |
| }; |
| }; |
| }; |
| |
| #include "dm814x-clocks.dtsi" |