| #ifndef LINUX_SSB_REGS_H_ |
| #define LINUX_SSB_REGS_H_ |
| |
| |
| /* SiliconBackplane Address Map. |
| * All regions may not exist on all chips. |
| */ |
| #define SSB_SDRAM_BASE 0x00000000U /* Physical SDRAM */ |
| #define SSB_PCI_MEM 0x08000000U /* Host Mode sb2pcitranslation0 (64 MB) */ |
| #define SSB_PCI_CFG 0x0c000000U /* Host Mode sb2pcitranslation1 (64 MB) */ |
| #define SSB_SDRAM_SWAPPED 0x10000000U /* Byteswapped Physical SDRAM */ |
| #define SSB_ENUM_BASE 0x18000000U /* Enumeration space base */ |
| #define SSB_ENUM_LIMIT 0x18010000U /* Enumeration space limit */ |
| |
| #define SSB_FLASH2 0x1c000000U /* Flash Region 2 (region 1 shadowed here) */ |
| #define SSB_FLASH2_SZ 0x02000000U /* Size of Flash Region 2 */ |
| |
| #define SSB_EXTIF_BASE 0x1f000000U /* External Interface region base address */ |
| #define SSB_FLASH1 0x1fc00000U /* Flash Region 1 */ |
| #define SSB_FLASH1_SZ 0x00400000U /* Size of Flash Region 1 */ |
| |
| #define SSB_PCI_DMA 0x40000000U /* Client Mode sb2pcitranslation2 (1 GB) */ |
| #define SSB_PCI_DMA_SZ 0x40000000U /* Client Mode sb2pcitranslation2 size in bytes */ |
| #define SSB_PCIE_DMA_L32 0x00000000U /* PCIE Client Mode sb2pcitranslation2 (2 ZettaBytes), low 32 bits */ |
| #define SSB_PCIE_DMA_H32 0x80000000U /* PCIE Client Mode sb2pcitranslation2 (2 ZettaBytes), high 32 bits */ |
| #define SSB_EUART (SSB_EXTIF_BASE + 0x00800000) |
| #define SSB_LED (SSB_EXTIF_BASE + 0x00900000) |
| |
| |
| /* Enumeration space constants */ |
| #define SSB_CORE_SIZE 0x1000 /* Size of a core MMIO area */ |
| #define SSB_MAX_NR_CORES ((SSB_ENUM_LIMIT - SSB_ENUM_BASE) / SSB_CORE_SIZE) |
| |
| |
| /* mips address */ |
| #define SSB_EJTAG 0xff200000 /* MIPS EJTAG space (2M) */ |
| |
| |
| /* SSB PCI config space registers. */ |
| #define SSB_PMCSR 0x44 |
| #define SSB_PE 0x100 |
| #define SSB_BAR0_WIN 0x80 /* Backplane address space 0 */ |
| #define SSB_BAR1_WIN 0x84 /* Backplane address space 1 */ |
| #define SSB_SPROMCTL 0x88 /* SPROM control */ |
| #define SSB_SPROMCTL_WE 0x10 /* SPROM write enable */ |
| #define SSB_BAR1_CONTROL 0x8c /* Address space 1 burst control */ |
| #define SSB_PCI_IRQS 0x90 /* PCI interrupts */ |
| #define SSB_PCI_IRQMASK 0x94 /* PCI IRQ control and mask (pcirev >= 6 only) */ |
| #define SSB_BACKPLANE_IRQS 0x98 /* Backplane Interrupts */ |
| #define SSB_GPIO_IN 0xB0 /* GPIO Input (pcirev >= 3 only) */ |
| #define SSB_GPIO_OUT 0xB4 /* GPIO Output (pcirev >= 3 only) */ |
| #define SSB_GPIO_OUT_ENABLE 0xB8 /* GPIO Output Enable/Disable (pcirev >= 3 only) */ |
| #define SSB_GPIO_SCS 0x10 /* PCI config space bit 4 for 4306c0 slow clock source */ |
| #define SSB_GPIO_HWRAD 0x20 /* PCI config space GPIO 13 for hw radio disable */ |
| #define SSB_GPIO_XTAL 0x40 /* PCI config space GPIO 14 for Xtal powerup */ |
| #define SSB_GPIO_PLL 0x80 /* PCI config space GPIO 15 for PLL powerdown */ |
| |
| |
| #define SSB_BAR0_MAX_RETRIES 50 |
| |
| /* Silicon backplane configuration register definitions */ |
| #define SSB_IPSFLAG 0x0F08 |
| #define SSB_IPSFLAG_IRQ1 0x0000003F /* which sbflags get routed to mips interrupt 1 */ |
| #define SSB_IPSFLAG_IRQ1_SHIFT 0 |
| #define SSB_IPSFLAG_IRQ2 0x00003F00 /* which sbflags get routed to mips interrupt 2 */ |
| #define SSB_IPSFLAG_IRQ2_SHIFT 8 |
| #define SSB_IPSFLAG_IRQ3 0x003F0000 /* which sbflags get routed to mips interrupt 3 */ |
| #define SSB_IPSFLAG_IRQ3_SHIFT 16 |
| #define SSB_IPSFLAG_IRQ4 0x3F000000 /* which sbflags get routed to mips interrupt 4 */ |
| #define SSB_IPSFLAG_IRQ4_SHIFT 24 |
| #define SSB_TPSFLAG 0x0F18 |
| #define SSB_TPSFLAG_BPFLAG 0x0000003F /* Backplane flag # */ |
| #define SSB_TPSFLAG_ALWAYSIRQ 0x00000040 /* IRQ is always sent on the Backplane */ |
| #define SSB_TMERRLOGA 0x0F48 |
| #define SSB_TMERRLOG 0x0F50 |
| #define SSB_ADMATCH3 0x0F60 |
| #define SSB_ADMATCH2 0x0F68 |
| #define SSB_ADMATCH1 0x0F70 |
| #define SSB_IMSTATE 0x0F90 /* SB Initiator Agent State */ |
| #define SSB_IMSTATE_PC 0x0000000f /* Pipe Count */ |
| #define SSB_IMSTATE_AP_MASK 0x00000030 /* Arbitration Priority */ |
| #define SSB_IMSTATE_AP_BOTH 0x00000000 /* Use both timeslices and token */ |
| #define SSB_IMSTATE_AP_TS 0x00000010 /* Use timeslices only */ |
| #define SSB_IMSTATE_AP_TK 0x00000020 /* Use token only */ |
| #define SSB_IMSTATE_AP_RSV 0x00000030 /* Reserved */ |
| #define SSB_IMSTATE_IBE 0x00020000 /* In Band Error */ |
| #define SSB_IMSTATE_TO 0x00040000 /* Timeout */ |
| #define SSB_IMSTATE_BUSY 0x01800000 /* Busy (Backplane rev >= 2.3 only) */ |
| #define SSB_IMSTATE_REJECT 0x02000000 /* Reject (Backplane rev >= 2.3 only) */ |
| #define SSB_INTVEC 0x0F94 /* SB Interrupt Mask */ |
| #define SSB_INTVEC_PCI 0x00000001 /* Enable interrupts for PCI */ |
| #define SSB_INTVEC_ENET0 0x00000002 /* Enable interrupts for enet 0 */ |
| #define SSB_INTVEC_ILINE20 0x00000004 /* Enable interrupts for iline20 */ |
| #define SSB_INTVEC_CODEC 0x00000008 /* Enable interrupts for v90 codec */ |
| #define SSB_INTVEC_USB 0x00000010 /* Enable interrupts for usb */ |
| #define SSB_INTVEC_EXTIF 0x00000020 /* Enable interrupts for external i/f */ |
| #define SSB_INTVEC_ENET1 0x00000040 /* Enable interrupts for enet 1 */ |
| #define SSB_TMSLOW 0x0F98 /* SB Target State Low */ |
| #define SSB_TMSLOW_RESET 0x00000001 /* Reset */ |
| #define SSB_TMSLOW_REJECT 0x00000002 /* Reject (Standard Backplane) */ |
| #define SSB_TMSLOW_REJECT_23 0x00000004 /* Reject (Backplane rev 2.3) */ |
| #define SSB_TMSLOW_CLOCK 0x00010000 /* Clock Enable */ |
| #define SSB_TMSLOW_FGC 0x00020000 /* Force Gated Clocks On */ |
| #define SSB_TMSLOW_PE 0x40000000 /* Power Management Enable */ |
| #define SSB_TMSLOW_BE 0x80000000 /* BIST Enable */ |
| #define SSB_TMSHIGH 0x0F9C /* SB Target State High */ |
| #define SSB_TMSHIGH_SERR 0x00000001 /* S-error */ |
| #define SSB_TMSHIGH_INT 0x00000002 /* Interrupt */ |
| #define SSB_TMSHIGH_BUSY 0x00000004 /* Busy */ |
| #define SSB_TMSHIGH_TO 0x00000020 /* Timeout. Backplane rev >= 2.3 only */ |
| #define SSB_TMSHIGH_COREFL 0x1FFF0000 /* Core specific flags */ |
| #define SSB_TMSHIGH_COREFL_SHIFT 16 |
| #define SSB_TMSHIGH_DMA64 0x10000000 /* 64bit DMA supported */ |
| #define SSB_TMSHIGH_GCR 0x20000000 /* Gated Clock Request */ |
| #define SSB_TMSHIGH_BISTF 0x40000000 /* BIST Failed */ |
| #define SSB_TMSHIGH_BISTD 0x80000000 /* BIST Done */ |
| #define SSB_BWA0 0x0FA0 |
| #define SSB_IMCFGLO 0x0FA8 |
| #define SSB_IMCFGLO_SERTO 0x00000007 /* Service timeout */ |
| #define SSB_IMCFGLO_REQTO 0x00000070 /* Request timeout */ |
| #define SSB_IMCFGLO_REQTO_SHIFT 4 |
| #define SSB_IMCFGLO_CONNID 0x00FF0000 /* Connection ID */ |
| #define SSB_IMCFGLO_CONNID_SHIFT 16 |
| #define SSB_IMCFGHI 0x0FAC |
| #define SSB_ADMATCH0 0x0FB0 |
| #define SSB_TMCFGLO 0x0FB8 |
| #define SSB_TMCFGHI 0x0FBC |
| #define SSB_BCONFIG 0x0FC0 |
| #define SSB_BSTATE 0x0FC8 |
| #define SSB_ACTCFG 0x0FD8 |
| #define SSB_FLAGST 0x0FE8 |
| #define SSB_IDLOW 0x0FF8 |
| #define SSB_IDLOW_CFGSP 0x00000003 /* Config Space */ |
| #define SSB_IDLOW_ADDRNGE 0x00000038 /* Address Ranges supported */ |
| #define SSB_IDLOW_ADDRNGE_SHIFT 3 |
| #define SSB_IDLOW_SYNC 0x00000040 |
| #define SSB_IDLOW_INITIATOR 0x00000080 |
| #define SSB_IDLOW_MIBL 0x00000F00 /* Minimum Backplane latency */ |
| #define SSB_IDLOW_MIBL_SHIFT 8 |
| #define SSB_IDLOW_MABL 0x0000F000 /* Maximum Backplane latency */ |
| #define SSB_IDLOW_MABL_SHIFT 12 |
| #define SSB_IDLOW_TIF 0x00010000 /* This Initiator is first */ |
| #define SSB_IDLOW_CCW 0x000C0000 /* Cycle counter width */ |
| #define SSB_IDLOW_CCW_SHIFT 18 |
| #define SSB_IDLOW_TPT 0x00F00000 /* Target ports */ |
| #define SSB_IDLOW_TPT_SHIFT 20 |
| #define SSB_IDLOW_INITP 0x0F000000 /* Initiator ports */ |
| #define SSB_IDLOW_INITP_SHIFT 24 |
| #define SSB_IDLOW_SSBREV 0xF0000000 /* Sonics Backplane Revision code */ |
| #define SSB_IDLOW_SSBREV_22 0x00000000 /* <= 2.2 */ |
| #define SSB_IDLOW_SSBREV_23 0x10000000 /* 2.3 */ |
| #define SSB_IDLOW_SSBREV_24 0x40000000 /* ?? Found in BCM4328 */ |
| #define SSB_IDLOW_SSBREV_25 0x50000000 /* ?? Not Found yet */ |
| #define SSB_IDLOW_SSBREV_26 0x60000000 /* ?? Found in some BCM4311/2 */ |
| #define SSB_IDLOW_SSBREV_27 0x70000000 /* ?? Found in some BCM4311/2 */ |
| #define SSB_IDHIGH 0x0FFC /* SB Identification High */ |
| #define SSB_IDHIGH_RCLO 0x0000000F /* Revision Code (low part) */ |
| #define SSB_IDHIGH_CC 0x00008FF0 /* Core Code */ |
| #define SSB_IDHIGH_CC_SHIFT 4 |
| #define SSB_IDHIGH_RCHI 0x00007000 /* Revision Code (high part) */ |
| #define SSB_IDHIGH_RCHI_SHIFT 8 /* yes, shift 8 is right */ |
| #define SSB_IDHIGH_VC 0xFFFF0000 /* Vendor Code */ |
| #define SSB_IDHIGH_VC_SHIFT 16 |
| |
| /* SPROM shadow area. If not otherwise noted, fields are |
| * two bytes wide. Note that the SPROM can _only_ be read |
| * in two-byte quantities. |
| */ |
| #define SSB_SPROMSIZE_WORDS 64 |
| #define SSB_SPROMSIZE_BYTES (SSB_SPROMSIZE_WORDS * sizeof(u16)) |
| #define SSB_SPROMSIZE_WORDS_R123 64 |
| #define SSB_SPROMSIZE_WORDS_R4 220 |
| #define SSB_SPROMSIZE_BYTES_R123 (SSB_SPROMSIZE_WORDS_R123 * sizeof(u16)) |
| #define SSB_SPROMSIZE_BYTES_R4 (SSB_SPROMSIZE_WORDS_R4 * sizeof(u16)) |
| #define SSB_SPROMSIZE_WORDS_R10 230 |
| #define SSB_SPROM_BASE1 0x1000 |
| #define SSB_SPROM_BASE31 0x0800 |
| #define SSB_SPROM_REVISION 0x007E |
| #define SSB_SPROM_REVISION_REV 0x00FF /* SPROM Revision number */ |
| #define SSB_SPROM_REVISION_CRC 0xFF00 /* SPROM CRC8 value */ |
| #define SSB_SPROM_REVISION_CRC_SHIFT 8 |
| |
| /* SPROM Revision 1 */ |
| #define SSB_SPROM1_SPID 0x0004 /* Subsystem Product ID for PCI */ |
| #define SSB_SPROM1_SVID 0x0006 /* Subsystem Vendor ID for PCI */ |
| #define SSB_SPROM1_PID 0x0008 /* Product ID for PCI */ |
| #define SSB_SPROM1_IL0MAC 0x0048 /* 6 bytes MAC address for 802.11b/g */ |
| #define SSB_SPROM1_ET0MAC 0x004E /* 6 bytes MAC address for Ethernet */ |
| #define SSB_SPROM1_ET1MAC 0x0054 /* 6 bytes MAC address for 802.11a */ |
| #define SSB_SPROM1_ETHPHY 0x005A /* Ethernet PHY settings */ |
| #define SSB_SPROM1_ETHPHY_ET0A 0x001F /* MII Address for enet0 */ |
| #define SSB_SPROM1_ETHPHY_ET1A 0x03E0 /* MII Address for enet1 */ |
| #define SSB_SPROM1_ETHPHY_ET1A_SHIFT 5 |
| #define SSB_SPROM1_ETHPHY_ET0M (1<<14) /* MDIO for enet0 */ |
| #define SSB_SPROM1_ETHPHY_ET1M (1<<15) /* MDIO for enet1 */ |
| #define SSB_SPROM1_BINF 0x005C /* Board info */ |
| #define SSB_SPROM1_BINF_BREV 0x00FF /* Board Revision */ |
| #define SSB_SPROM1_BINF_CCODE 0x0F00 /* Country Code */ |
| #define SSB_SPROM1_BINF_CCODE_SHIFT 8 |
| #define SSB_SPROM1_BINF_ANTBG 0x3000 /* Available B-PHY and G-PHY antennas */ |
| #define SSB_SPROM1_BINF_ANTBG_SHIFT 12 |
| #define SSB_SPROM1_BINF_ANTA 0xC000 /* Available A-PHY antennas */ |
| #define SSB_SPROM1_BINF_ANTA_SHIFT 14 |
| #define SSB_SPROM1_PA0B0 0x005E |
| #define SSB_SPROM1_PA0B1 0x0060 |
| #define SSB_SPROM1_PA0B2 0x0062 |
| #define SSB_SPROM1_GPIOA 0x0064 /* General Purpose IO pins 0 and 1 */ |
| #define SSB_SPROM1_GPIOA_P0 0x00FF /* Pin 0 */ |
| #define SSB_SPROM1_GPIOA_P1 0xFF00 /* Pin 1 */ |
| #define SSB_SPROM1_GPIOA_P1_SHIFT 8 |
| #define SSB_SPROM1_GPIOB 0x0066 /* General Purpuse IO pins 2 and 3 */ |
| #define SSB_SPROM1_GPIOB_P2 0x00FF /* Pin 2 */ |
| #define SSB_SPROM1_GPIOB_P3 0xFF00 /* Pin 3 */ |
| #define SSB_SPROM1_GPIOB_P3_SHIFT 8 |
| #define SSB_SPROM1_MAXPWR 0x0068 /* Power Amplifier Max Power */ |
| #define SSB_SPROM1_MAXPWR_BG 0x00FF /* B-PHY and G-PHY (in dBm Q5.2) */ |
| #define SSB_SPROM1_MAXPWR_A 0xFF00 /* A-PHY (in dBm Q5.2) */ |
| #define SSB_SPROM1_MAXPWR_A_SHIFT 8 |
| #define SSB_SPROM1_PA1B0 0x006A |
| #define SSB_SPROM1_PA1B1 0x006C |
| #define SSB_SPROM1_PA1B2 0x006E |
| #define SSB_SPROM1_ITSSI 0x0070 /* Idle TSSI Target */ |
| #define SSB_SPROM1_ITSSI_BG 0x00FF /* B-PHY and G-PHY*/ |
| #define SSB_SPROM1_ITSSI_A 0xFF00 /* A-PHY */ |
| #define SSB_SPROM1_ITSSI_A_SHIFT 8 |
| #define SSB_SPROM1_BFLLO 0x0072 /* Boardflags (low 16 bits) */ |
| #define SSB_SPROM1_AGAIN 0x0074 /* Antenna Gain (in dBm Q5.2) */ |
| #define SSB_SPROM1_AGAIN_BG 0x00FF /* B-PHY and G-PHY */ |
| #define SSB_SPROM1_AGAIN_BG_SHIFT 0 |
| #define SSB_SPROM1_AGAIN_A 0xFF00 /* A-PHY */ |
| #define SSB_SPROM1_AGAIN_A_SHIFT 8 |
| #define SSB_SPROM1_CCODE 0x0076 |
| |
| /* SPROM Revision 2 (inherits from rev 1) */ |
| #define SSB_SPROM2_BFLHI 0x0038 /* Boardflags (high 16 bits) */ |
| #define SSB_SPROM2_MAXP_A 0x003A /* A-PHY Max Power */ |
| #define SSB_SPROM2_MAXP_A_HI 0x00FF /* Max Power High */ |
| #define SSB_SPROM2_MAXP_A_LO 0xFF00 /* Max Power Low */ |
| #define SSB_SPROM2_MAXP_A_LO_SHIFT 8 |
| #define SSB_SPROM2_PA1LOB0 0x003C /* A-PHY PowerAmplifier Low Settings */ |
| #define SSB_SPROM2_PA1LOB1 0x003E /* A-PHY PowerAmplifier Low Settings */ |
| #define SSB_SPROM2_PA1LOB2 0x0040 /* A-PHY PowerAmplifier Low Settings */ |
| #define SSB_SPROM2_PA1HIB0 0x0042 /* A-PHY PowerAmplifier High Settings */ |
| #define SSB_SPROM2_PA1HIB1 0x0044 /* A-PHY PowerAmplifier High Settings */ |
| #define SSB_SPROM2_PA1HIB2 0x0046 /* A-PHY PowerAmplifier High Settings */ |
| #define SSB_SPROM2_OPO 0x0078 /* OFDM Power Offset from CCK Level */ |
| #define SSB_SPROM2_OPO_VALUE 0x00FF |
| #define SSB_SPROM2_OPO_UNUSED 0xFF00 |
| #define SSB_SPROM2_CCODE 0x007C /* Two char Country Code */ |
| |
| /* SPROM Revision 3 (inherits most data from rev 2) */ |
| #define SSB_SPROM3_OFDMAPO 0x002C /* A-PHY OFDM Mid Power Offset (4 bytes, BigEndian) */ |
| #define SSB_SPROM3_OFDMALPO 0x0030 /* A-PHY OFDM Low Power Offset (4 bytes, BigEndian) */ |
| #define SSB_SPROM3_OFDMAHPO 0x0034 /* A-PHY OFDM High Power Offset (4 bytes, BigEndian) */ |
| #define SSB_SPROM3_GPIOLDC 0x0042 /* GPIO LED Powersave Duty Cycle (4 bytes, BigEndian) */ |
| #define SSB_SPROM3_GPIOLDC_OFF 0x0000FF00 /* Off Count */ |
| #define SSB_SPROM3_GPIOLDC_OFF_SHIFT 8 |
| #define SSB_SPROM3_GPIOLDC_ON 0x00FF0000 /* On Count */ |
| #define SSB_SPROM3_GPIOLDC_ON_SHIFT 16 |
| #define SSB_SPROM3_IL0MAC 0x004A /* 6 bytes MAC address for 802.11b/g */ |
| #define SSB_SPROM3_CCKPO 0x0078 /* CCK Power Offset */ |
| #define SSB_SPROM3_CCKPO_1M 0x000F /* 1M Rate PO */ |
| #define SSB_SPROM3_CCKPO_2M 0x00F0 /* 2M Rate PO */ |
| #define SSB_SPROM3_CCKPO_2M_SHIFT 4 |
| #define SSB_SPROM3_CCKPO_55M 0x0F00 /* 5.5M Rate PO */ |
| #define SSB_SPROM3_CCKPO_55M_SHIFT 8 |
| #define SSB_SPROM3_CCKPO_11M 0xF000 /* 11M Rate PO */ |
| #define SSB_SPROM3_CCKPO_11M_SHIFT 12 |
| #define SSB_SPROM3_OFDMGPO 0x107A /* G-PHY OFDM Power Offset (4 bytes, BigEndian) */ |
| |
| /* SPROM Revision 4 */ |
| #define SSB_SPROM4_BOARDREV 0x0042 /* Board revision */ |
| #define SSB_SPROM4_BFLLO 0x0044 /* Boardflags (low 16 bits) */ |
| #define SSB_SPROM4_BFLHI 0x0046 /* Board Flags Hi */ |
| #define SSB_SPROM4_BFL2LO 0x0048 /* Board flags 2 (low 16 bits) */ |
| #define SSB_SPROM4_BFL2HI 0x004A /* Board flags 2 Hi */ |
| #define SSB_SPROM4_IL0MAC 0x004C /* 6 byte MAC address for a/b/g/n */ |
| #define SSB_SPROM4_CCODE 0x0052 /* Country Code (2 bytes) */ |
| #define SSB_SPROM4_GPIOA 0x0056 /* Gen. Purpose IO # 0 and 1 */ |
| #define SSB_SPROM4_GPIOA_P0 0x00FF /* Pin 0 */ |
| #define SSB_SPROM4_GPIOA_P1 0xFF00 /* Pin 1 */ |
| #define SSB_SPROM4_GPIOA_P1_SHIFT 8 |
| #define SSB_SPROM4_GPIOB 0x0058 /* Gen. Purpose IO # 2 and 3 */ |
| #define SSB_SPROM4_GPIOB_P2 0x00FF /* Pin 2 */ |
| #define SSB_SPROM4_GPIOB_P3 0xFF00 /* Pin 3 */ |
| #define SSB_SPROM4_GPIOB_P3_SHIFT 8 |
| #define SSB_SPROM4_ETHPHY 0x005A /* Ethernet PHY settings ?? */ |
| #define SSB_SPROM4_ETHPHY_ET0A 0x001F /* MII Address for enet0 */ |
| #define SSB_SPROM4_ETHPHY_ET1A 0x03E0 /* MII Address for enet1 */ |
| #define SSB_SPROM4_ETHPHY_ET1A_SHIFT 5 |
| #define SSB_SPROM4_ETHPHY_ET0M (1<<14) /* MDIO for enet0 */ |
| #define SSB_SPROM4_ETHPHY_ET1M (1<<15) /* MDIO for enet1 */ |
| #define SSB_SPROM4_ANTAVAIL 0x005C /* Antenna available bitfields */ |
| #define SSB_SPROM4_ANTAVAIL_BG 0x00FF /* B-PHY and G-PHY bitfield */ |
| #define SSB_SPROM4_ANTAVAIL_BG_SHIFT 0 |
| #define SSB_SPROM4_ANTAVAIL_A 0xFF00 /* A-PHY bitfield */ |
| #define SSB_SPROM4_ANTAVAIL_A_SHIFT 8 |
| #define SSB_SPROM4_AGAIN01 0x005E /* Antenna Gain (in dBm Q5.2) */ |
| #define SSB_SPROM4_AGAIN0 0x00FF /* Antenna 0 */ |
| #define SSB_SPROM4_AGAIN0_SHIFT 0 |
| #define SSB_SPROM4_AGAIN1 0xFF00 /* Antenna 1 */ |
| #define SSB_SPROM4_AGAIN1_SHIFT 8 |
| #define SSB_SPROM4_AGAIN23 0x0060 |
| #define SSB_SPROM4_AGAIN2 0x00FF /* Antenna 2 */ |
| #define SSB_SPROM4_AGAIN2_SHIFT 0 |
| #define SSB_SPROM4_AGAIN3 0xFF00 /* Antenna 3 */ |
| #define SSB_SPROM4_AGAIN3_SHIFT 8 |
| #define SSB_SPROM4_TXPID2G01 0x0062 /* TX Power Index 2GHz */ |
| #define SSB_SPROM4_TXPID2G0 0x00FF |
| #define SSB_SPROM4_TXPID2G0_SHIFT 0 |
| #define SSB_SPROM4_TXPID2G1 0xFF00 |
| #define SSB_SPROM4_TXPID2G1_SHIFT 8 |
| #define SSB_SPROM4_TXPID2G23 0x0064 /* TX Power Index 2GHz */ |
| #define SSB_SPROM4_TXPID2G2 0x00FF |
| #define SSB_SPROM4_TXPID2G2_SHIFT 0 |
| #define SSB_SPROM4_TXPID2G3 0xFF00 |
| #define SSB_SPROM4_TXPID2G3_SHIFT 8 |
| #define SSB_SPROM4_TXPID5G01 0x0066 /* TX Power Index 5GHz middle subband */ |
| #define SSB_SPROM4_TXPID5G0 0x00FF |
| #define SSB_SPROM4_TXPID5G0_SHIFT 0 |
| #define SSB_SPROM4_TXPID5G1 0xFF00 |
| #define SSB_SPROM4_TXPID5G1_SHIFT 8 |
| #define SSB_SPROM4_TXPID5G23 0x0068 /* TX Power Index 5GHz middle subband */ |
| #define SSB_SPROM4_TXPID5G2 0x00FF |
| #define SSB_SPROM4_TXPID5G2_SHIFT 0 |
| #define SSB_SPROM4_TXPID5G3 0xFF00 |
| #define SSB_SPROM4_TXPID5G3_SHIFT 8 |
| #define SSB_SPROM4_TXPID5GL01 0x006A /* TX Power Index 5GHz low subband */ |
| #define SSB_SPROM4_TXPID5GL0 0x00FF |
| #define SSB_SPROM4_TXPID5GL0_SHIFT 0 |
| #define SSB_SPROM4_TXPID5GL1 0xFF00 |
| #define SSB_SPROM4_TXPID5GL1_SHIFT 8 |
| #define SSB_SPROM4_TXPID5GL23 0x006C /* TX Power Index 5GHz low subband */ |
| #define SSB_SPROM4_TXPID5GL2 0x00FF |
| #define SSB_SPROM4_TXPID5GL2_SHIFT 0 |
| #define SSB_SPROM4_TXPID5GL3 0xFF00 |
| #define SSB_SPROM4_TXPID5GL3_SHIFT 8 |
| #define SSB_SPROM4_TXPID5GH01 0x006E /* TX Power Index 5GHz high subband */ |
| #define SSB_SPROM4_TXPID5GH0 0x00FF |
| #define SSB_SPROM4_TXPID5GH0_SHIFT 0 |
| #define SSB_SPROM4_TXPID5GH1 0xFF00 |
| #define SSB_SPROM4_TXPID5GH1_SHIFT 8 |
| #define SSB_SPROM4_TXPID5GH23 0x0070 /* TX Power Index 5GHz high subband */ |
| #define SSB_SPROM4_TXPID5GH2 0x00FF |
| #define SSB_SPROM4_TXPID5GH2_SHIFT 0 |
| #define SSB_SPROM4_TXPID5GH3 0xFF00 |
| #define SSB_SPROM4_TXPID5GH3_SHIFT 8 |
| #define SSB_SPROM4_MAXP_BG 0x0080 /* Max Power BG in path 1 */ |
| #define SSB_SPROM4_MAXP_BG_MASK 0x00FF /* Mask for Max Power BG */ |
| #define SSB_SPROM4_ITSSI_BG 0xFF00 /* Mask for path 1 itssi_bg */ |
| #define SSB_SPROM4_ITSSI_BG_SHIFT 8 |
| #define SSB_SPROM4_MAXP_A 0x008A /* Max Power A in path 1 */ |
| #define SSB_SPROM4_MAXP_A_MASK 0x00FF /* Mask for Max Power A */ |
| #define SSB_SPROM4_ITSSI_A 0xFF00 /* Mask for path 1 itssi_a */ |
| #define SSB_SPROM4_ITSSI_A_SHIFT 8 |
| #define SSB_SPROM4_PA0B0 0x0082 /* The paXbY locations are */ |
| #define SSB_SPROM4_PA0B1 0x0084 /* only guesses */ |
| #define SSB_SPROM4_PA0B2 0x0086 |
| #define SSB_SPROM4_PA1B0 0x008E |
| #define SSB_SPROM4_PA1B1 0x0090 |
| #define SSB_SPROM4_PA1B2 0x0092 |
| |
| /* SPROM Revision 5 (inherits most data from rev 4) */ |
| #define SSB_SPROM5_CCODE 0x0044 /* Country Code (2 bytes) */ |
| #define SSB_SPROM5_BFLLO 0x004A /* Boardflags (low 16 bits) */ |
| #define SSB_SPROM5_BFLHI 0x004C /* Board Flags Hi */ |
| #define SSB_SPROM5_BFL2LO 0x004E /* Board flags 2 (low 16 bits) */ |
| #define SSB_SPROM5_BFL2HI 0x0050 /* Board flags 2 Hi */ |
| #define SSB_SPROM5_IL0MAC 0x0052 /* 6 byte MAC address for a/b/g/n */ |
| #define SSB_SPROM5_GPIOA 0x0076 /* Gen. Purpose IO # 0 and 1 */ |
| #define SSB_SPROM5_GPIOA_P0 0x00FF /* Pin 0 */ |
| #define SSB_SPROM5_GPIOA_P1 0xFF00 /* Pin 1 */ |
| #define SSB_SPROM5_GPIOA_P1_SHIFT 8 |
| #define SSB_SPROM5_GPIOB 0x0078 /* Gen. Purpose IO # 2 and 3 */ |
| #define SSB_SPROM5_GPIOB_P2 0x00FF /* Pin 2 */ |
| #define SSB_SPROM5_GPIOB_P3 0xFF00 /* Pin 3 */ |
| #define SSB_SPROM5_GPIOB_P3_SHIFT 8 |
| |
| /* SPROM Revision 8 */ |
| #define SSB_SPROM8_BOARDREV 0x0082 /* Board revision */ |
| #define SSB_SPROM8_BFLLO 0x0084 /* Board flags (bits 0-15) */ |
| #define SSB_SPROM8_BFLHI 0x0086 /* Board flags (bits 16-31) */ |
| #define SSB_SPROM8_BFL2LO 0x0088 /* Board flags (bits 32-47) */ |
| #define SSB_SPROM8_BFL2HI 0x008A /* Board flags (bits 48-63) */ |
| #define SSB_SPROM8_IL0MAC 0x008C /* 6 byte MAC address */ |
| #define SSB_SPROM8_CCODE 0x0092 /* 2 byte country code */ |
| #define SSB_SPROM8_GPIOA 0x0096 /*Gen. Purpose IO # 0 and 1 */ |
| #define SSB_SPROM8_GPIOA_P0 0x00FF /* Pin 0 */ |
| #define SSB_SPROM8_GPIOA_P1 0xFF00 /* Pin 1 */ |
| #define SSB_SPROM8_GPIOA_P1_SHIFT 8 |
| #define SSB_SPROM8_GPIOB 0x0098 /* Gen. Purpose IO # 2 and 3 */ |
| #define SSB_SPROM8_GPIOB_P2 0x00FF /* Pin 2 */ |
| #define SSB_SPROM8_GPIOB_P3 0xFF00 /* Pin 3 */ |
| #define SSB_SPROM8_GPIOB_P3_SHIFT 8 |
| #define SSB_SPROM8_LEDDC 0x009A |
| #define SSB_SPROM8_LEDDC_ON 0xFF00 /* oncount */ |
| #define SSB_SPROM8_LEDDC_ON_SHIFT 8 |
| #define SSB_SPROM8_LEDDC_OFF 0x00FF /* offcount */ |
| #define SSB_SPROM8_LEDDC_OFF_SHIFT 0 |
| #define SSB_SPROM8_ANTAVAIL 0x009C /* Antenna available bitfields*/ |
| #define SSB_SPROM8_ANTAVAIL_A 0xFF00 /* A-PHY bitfield */ |
| #define SSB_SPROM8_ANTAVAIL_A_SHIFT 8 |
| #define SSB_SPROM8_ANTAVAIL_BG 0x00FF /* B-PHY and G-PHY bitfield */ |
| #define SSB_SPROM8_ANTAVAIL_BG_SHIFT 0 |
| #define SSB_SPROM8_AGAIN01 0x009E /* Antenna Gain (in dBm Q5.2) */ |
| #define SSB_SPROM8_AGAIN0 0x00FF /* Antenna 0 */ |
| #define SSB_SPROM8_AGAIN0_SHIFT 0 |
| #define SSB_SPROM8_AGAIN1 0xFF00 /* Antenna 1 */ |
| #define SSB_SPROM8_AGAIN1_SHIFT 8 |
| #define SSB_SPROM8_AGAIN23 0x00A0 |
| #define SSB_SPROM8_AGAIN2 0x00FF /* Antenna 2 */ |
| #define SSB_SPROM8_AGAIN2_SHIFT 0 |
| #define SSB_SPROM8_AGAIN3 0xFF00 /* Antenna 3 */ |
| #define SSB_SPROM8_AGAIN3_SHIFT 8 |
| #define SSB_SPROM8_TXRXC 0x00A2 |
| #define SSB_SPROM8_TXRXC_TXCHAIN 0x000f |
| #define SSB_SPROM8_TXRXC_TXCHAIN_SHIFT 0 |
| #define SSB_SPROM8_TXRXC_RXCHAIN 0x00f0 |
| #define SSB_SPROM8_TXRXC_RXCHAIN_SHIFT 4 |
| #define SSB_SPROM8_TXRXC_SWITCH 0xff00 |
| #define SSB_SPROM8_TXRXC_SWITCH_SHIFT 8 |
| #define SSB_SPROM8_RSSIPARM2G 0x00A4 /* RSSI params for 2GHz */ |
| #define SSB_SPROM8_RSSISMF2G 0x000F |
| #define SSB_SPROM8_RSSISMC2G 0x00F0 |
| #define SSB_SPROM8_RSSISMC2G_SHIFT 4 |
| #define SSB_SPROM8_RSSISAV2G 0x0700 |
| #define SSB_SPROM8_RSSISAV2G_SHIFT 8 |
| #define SSB_SPROM8_BXA2G 0x1800 |
| #define SSB_SPROM8_BXA2G_SHIFT 11 |
| #define SSB_SPROM8_RSSIPARM5G 0x00A6 /* RSSI params for 5GHz */ |
| #define SSB_SPROM8_RSSISMF5G 0x000F |
| #define SSB_SPROM8_RSSISMC5G 0x00F0 |
| #define SSB_SPROM8_RSSISMC5G_SHIFT 4 |
| #define SSB_SPROM8_RSSISAV5G 0x0700 |
| #define SSB_SPROM8_RSSISAV5G_SHIFT 8 |
| #define SSB_SPROM8_BXA5G 0x1800 |
| #define SSB_SPROM8_BXA5G_SHIFT 11 |
| #define SSB_SPROM8_TRI25G 0x00A8 /* TX isolation 2.4&5.3GHz */ |
| #define SSB_SPROM8_TRI2G 0x00FF /* TX isolation 2.4GHz */ |
| #define SSB_SPROM8_TRI5G 0xFF00 /* TX isolation 5.3GHz */ |
| #define SSB_SPROM8_TRI5G_SHIFT 8 |
| #define SSB_SPROM8_TRI5GHL 0x00AA /* TX isolation 5.2/5.8GHz */ |
| #define SSB_SPROM8_TRI5GL 0x00FF /* TX isolation 5.2GHz */ |
| #define SSB_SPROM8_TRI5GH 0xFF00 /* TX isolation 5.8GHz */ |
| #define SSB_SPROM8_TRI5GH_SHIFT 8 |
| #define SSB_SPROM8_RXPO 0x00AC /* RX power offsets */ |
| #define SSB_SPROM8_RXPO2G 0x00FF /* 2GHz RX power offset */ |
| #define SSB_SPROM8_RXPO2G_SHIFT 0 |
| #define SSB_SPROM8_RXPO5G 0xFF00 /* 5GHz RX power offset */ |
| #define SSB_SPROM8_RXPO5G_SHIFT 8 |
| #define SSB_SPROM8_FEM2G 0x00AE |
| #define SSB_SPROM8_FEM5G 0x00B0 |
| #define SSB_SROM8_FEM_TSSIPOS 0x0001 |
| #define SSB_SROM8_FEM_TSSIPOS_SHIFT 0 |
| #define SSB_SROM8_FEM_EXTPA_GAIN 0x0006 |
| #define SSB_SROM8_FEM_EXTPA_GAIN_SHIFT 1 |
| #define SSB_SROM8_FEM_PDET_RANGE 0x00F8 |
| #define SSB_SROM8_FEM_PDET_RANGE_SHIFT 3 |
| #define SSB_SROM8_FEM_TR_ISO 0x0700 |
| #define SSB_SROM8_FEM_TR_ISO_SHIFT 8 |
| #define SSB_SROM8_FEM_ANTSWLUT 0xF800 |
| #define SSB_SROM8_FEM_ANTSWLUT_SHIFT 11 |
| #define SSB_SPROM8_THERMAL 0x00B2 |
| #define SSB_SPROM8_THERMAL_OFFSET 0x00ff |
| #define SSB_SPROM8_THERMAL_OFFSET_SHIFT 0 |
| #define SSB_SPROM8_THERMAL_TRESH 0xff00 |
| #define SSB_SPROM8_THERMAL_TRESH_SHIFT 8 |
| /* Temp sense related entries */ |
| #define SSB_SPROM8_RAWTS 0x00B4 |
| #define SSB_SPROM8_RAWTS_RAWTEMP 0x01ff |
| #define SSB_SPROM8_RAWTS_RAWTEMP_SHIFT 0 |
| #define SSB_SPROM8_RAWTS_MEASPOWER 0xfe00 |
| #define SSB_SPROM8_RAWTS_MEASPOWER_SHIFT 9 |
| #define SSB_SPROM8_OPT_CORRX 0x00B6 |
| #define SSB_SPROM8_OPT_CORRX_TEMP_SLOPE 0x00ff |
| #define SSB_SPROM8_OPT_CORRX_TEMP_SLOPE_SHIFT 0 |
| #define SSB_SPROM8_OPT_CORRX_TEMPCORRX 0xfc00 |
| #define SSB_SPROM8_OPT_CORRX_TEMPCORRX_SHIFT 10 |
| #define SSB_SPROM8_OPT_CORRX_TEMP_OPTION 0x0300 |
| #define SSB_SPROM8_OPT_CORRX_TEMP_OPTION_SHIFT 8 |
| /* FOC: freiquency offset correction, HWIQ: H/W IOCAL enable, IQSWP: IQ CAL swap disable */ |
| #define SSB_SPROM8_HWIQ_IQSWP 0x00B8 |
| #define SSB_SPROM8_HWIQ_IQSWP_FREQ_CORR 0x000f |
| #define SSB_SPROM8_HWIQ_IQSWP_FREQ_CORR_SHIFT 0 |
| #define SSB_SPROM8_HWIQ_IQSWP_IQCAL_SWP 0x0010 |
| #define SSB_SPROM8_HWIQ_IQSWP_IQCAL_SWP_SHIFT 4 |
| #define SSB_SPROM8_HWIQ_IQSWP_HW_IQCAL 0x0020 |
| #define SSB_SPROM8_HWIQ_IQSWP_HW_IQCAL_SHIFT 5 |
| #define SSB_SPROM8_TEMPDELTA 0x00BC |
| #define SSB_SPROM8_TEMPDELTA_PHYCAL 0x00ff |
| #define SSB_SPROM8_TEMPDELTA_PHYCAL_SHIFT 0 |
| #define SSB_SPROM8_TEMPDELTA_PERIOD 0x0f00 |
| #define SSB_SPROM8_TEMPDELTA_PERIOD_SHIFT 8 |
| #define SSB_SPROM8_TEMPDELTA_HYSTERESIS 0xf000 |
| #define SSB_SPROM8_TEMPDELTA_HYSTERESIS_SHIFT 12 |
| |
| /* There are 4 blocks with power info sharing the same layout */ |
| #define SSB_SROM8_PWR_INFO_CORE0 0x00C0 |
| #define SSB_SROM8_PWR_INFO_CORE1 0x00E0 |
| #define SSB_SROM8_PWR_INFO_CORE2 0x0100 |
| #define SSB_SROM8_PWR_INFO_CORE3 0x0120 |
| |
| #define SSB_SROM8_2G_MAXP_ITSSI 0x00 |
| #define SSB_SPROM8_2G_MAXP 0x00FF |
| #define SSB_SPROM8_2G_ITSSI 0xFF00 |
| #define SSB_SPROM8_2G_ITSSI_SHIFT 8 |
| #define SSB_SROM8_2G_PA_0 0x02 /* 2GHz power amp settings */ |
| #define SSB_SROM8_2G_PA_1 0x04 |
| #define SSB_SROM8_2G_PA_2 0x06 |
| #define SSB_SROM8_5G_MAXP_ITSSI 0x08 /* 5GHz ITSSI and 5.3GHz Max Power */ |
| #define SSB_SPROM8_5G_MAXP 0x00FF |
| #define SSB_SPROM8_5G_ITSSI 0xFF00 |
| #define SSB_SPROM8_5G_ITSSI_SHIFT 8 |
| #define SSB_SPROM8_5GHL_MAXP 0x0A /* 5.2GHz and 5.8GHz Max Power */ |
| #define SSB_SPROM8_5GH_MAXP 0x00FF |
| #define SSB_SPROM8_5GL_MAXP 0xFF00 |
| #define SSB_SPROM8_5GL_MAXP_SHIFT 8 |
| #define SSB_SROM8_5G_PA_0 0x0C /* 5.3GHz power amp settings */ |
| #define SSB_SROM8_5G_PA_1 0x0E |
| #define SSB_SROM8_5G_PA_2 0x10 |
| #define SSB_SROM8_5GL_PA_0 0x12 /* 5.2GHz power amp settings */ |
| #define SSB_SROM8_5GL_PA_1 0x14 |
| #define SSB_SROM8_5GL_PA_2 0x16 |
| #define SSB_SROM8_5GH_PA_0 0x18 /* 5.8GHz power amp settings */ |
| #define SSB_SROM8_5GH_PA_1 0x1A |
| #define SSB_SROM8_5GH_PA_2 0x1C |
| |
| /* TODO: Make it deprecated */ |
| #define SSB_SPROM8_MAXP_BG 0x00C0 /* Max Power 2GHz in path 1 */ |
| #define SSB_SPROM8_MAXP_BG_MASK 0x00FF /* Mask for Max Power 2GHz */ |
| #define SSB_SPROM8_ITSSI_BG 0xFF00 /* Mask for path 1 itssi_bg */ |
| #define SSB_SPROM8_ITSSI_BG_SHIFT 8 |
| #define SSB_SPROM8_PA0B0 0x00C2 /* 2GHz power amp settings */ |
| #define SSB_SPROM8_PA0B1 0x00C4 |
| #define SSB_SPROM8_PA0B2 0x00C6 |
| #define SSB_SPROM8_MAXP_A 0x00C8 /* Max Power 5.3GHz */ |
| #define SSB_SPROM8_MAXP_A_MASK 0x00FF /* Mask for Max Power 5.3GHz */ |
| #define SSB_SPROM8_ITSSI_A 0xFF00 /* Mask for path 1 itssi_a */ |
| #define SSB_SPROM8_ITSSI_A_SHIFT 8 |
| #define SSB_SPROM8_MAXP_AHL 0x00CA /* Max Power 5.2/5.8GHz */ |
| #define SSB_SPROM8_MAXP_AH_MASK 0x00FF /* Mask for Max Power 5.8GHz */ |
| #define SSB_SPROM8_MAXP_AL_MASK 0xFF00 /* Mask for Max Power 5.2GHz */ |
| #define SSB_SPROM8_MAXP_AL_SHIFT 8 |
| #define SSB_SPROM8_PA1B0 0x00CC /* 5.3GHz power amp settings */ |
| #define SSB_SPROM8_PA1B1 0x00CE |
| #define SSB_SPROM8_PA1B2 0x00D0 |
| #define SSB_SPROM8_PA1LOB0 0x00D2 /* 5.2GHz power amp settings */ |
| #define SSB_SPROM8_PA1LOB1 0x00D4 |
| #define SSB_SPROM8_PA1LOB2 0x00D6 |
| #define SSB_SPROM8_PA1HIB0 0x00D8 /* 5.8GHz power amp settings */ |
| #define SSB_SPROM8_PA1HIB1 0x00DA |
| #define SSB_SPROM8_PA1HIB2 0x00DC |
| |
| #define SSB_SPROM8_CCK2GPO 0x0140 /* CCK power offset */ |
| #define SSB_SPROM8_OFDM2GPO 0x0142 /* 2.4GHz OFDM power offset */ |
| #define SSB_SPROM8_OFDM5GPO 0x0146 /* 5.3GHz OFDM power offset */ |
| #define SSB_SPROM8_OFDM5GLPO 0x014A /* 5.2GHz OFDM power offset */ |
| #define SSB_SPROM8_OFDM5GHPO 0x014E /* 5.8GHz OFDM power offset */ |
| |
| #define SSB_SPROM8_2G_MCSPO 0x0152 |
| #define SSB_SPROM8_5G_MCSPO 0x0162 |
| #define SSB_SPROM8_5GL_MCSPO 0x0172 |
| #define SSB_SPROM8_5GH_MCSPO 0x0182 |
| |
| #define SSB_SPROM8_CDDPO 0x0192 |
| #define SSB_SPROM8_STBCPO 0x0194 |
| #define SSB_SPROM8_BW40PO 0x0196 |
| #define SSB_SPROM8_BWDUPPO 0x0198 |
| |
| /* Values for boardflags_lo read from SPROM */ |
| #define SSB_BFL_BTCOEXIST 0x0001 /* implements Bluetooth coexistance */ |
| #define SSB_BFL_PACTRL 0x0002 /* GPIO 9 controlling the PA */ |
| #define SSB_BFL_AIRLINEMODE 0x0004 /* implements GPIO 13 radio disable indication */ |
| #define SSB_BFL_RSSI 0x0008 /* software calculates nrssi slope. */ |
| #define SSB_BFL_ENETSPI 0x0010 /* has ephy roboswitch spi */ |
| #define SSB_BFL_XTAL_NOSLOW 0x0020 /* no slow clock available */ |
| #define SSB_BFL_CCKHIPWR 0x0040 /* can do high power CCK transmission */ |
| #define SSB_BFL_ENETADM 0x0080 /* has ADMtek switch */ |
| #define SSB_BFL_ENETVLAN 0x0100 /* can do vlan */ |
| #define SSB_BFL_AFTERBURNER 0x0200 /* supports Afterburner mode */ |
| #define SSB_BFL_NOPCI 0x0400 /* board leaves PCI floating */ |
| #define SSB_BFL_FEM 0x0800 /* supports the Front End Module */ |
| #define SSB_BFL_EXTLNA 0x1000 /* has an external LNA */ |
| #define SSB_BFL_HGPA 0x2000 /* had high gain PA */ |
| #define SSB_BFL_BTCMOD 0x4000 /* BFL_BTCOEXIST is given in alternate GPIOs */ |
| #define SSB_BFL_ALTIQ 0x8000 /* alternate I/Q settings */ |
| |
| /* Values for boardflags_hi read from SPROM */ |
| #define SSB_BFH_NOPA 0x0001 /* has no PA */ |
| #define SSB_BFH_RSSIINV 0x0002 /* RSSI uses positive slope (not TSSI) */ |
| #define SSB_BFH_PAREF 0x0004 /* uses the PARef LDO */ |
| #define SSB_BFH_3TSWITCH 0x0008 /* uses a triple throw switch shared with bluetooth */ |
| #define SSB_BFH_PHASESHIFT 0x0010 /* can support phase shifter */ |
| #define SSB_BFH_BUCKBOOST 0x0020 /* has buck/booster */ |
| #define SSB_BFH_FEM_BT 0x0040 /* has FEM and switch to share antenna with bluetooth */ |
| |
| /* Values for boardflags2_lo read from SPROM */ |
| #define SSB_BFL2_RXBB_INT_REG_DIS 0x0001 /* external RX BB regulator present */ |
| #define SSB_BFL2_APLL_WAR 0x0002 /* alternative A-band PLL settings implemented */ |
| #define SSB_BFL2_TXPWRCTRL_EN 0x0004 /* permits enabling TX Power Control */ |
| #define SSB_BFL2_2X4_DIV 0x0008 /* 2x4 diversity switch */ |
| #define SSB_BFL2_5G_PWRGAIN 0x0010 /* supports 5G band power gain */ |
| #define SSB_BFL2_PCIEWAR_OVR 0x0020 /* overrides ASPM and Clkreq settings */ |
| #define SSB_BFL2_CAESERS_BRD 0x0040 /* is Caesers board (unused) */ |
| #define SSB_BFL2_BTC3WIRE 0x0080 /* used 3-wire bluetooth coexist */ |
| #define SSB_BFL2_SKWRKFEM_BRD 0x0100 /* 4321mcm93 uses Skyworks FEM */ |
| #define SSB_BFL2_SPUR_WAR 0x0200 /* has a workaround for clock-harmonic spurs */ |
| #define SSB_BFL2_GPLL_WAR 0x0400 /* altenative G-band PLL settings implemented */ |
| |
| /* Values for SSB_SPROM1_BINF_CCODE */ |
| enum { |
| SSB_SPROM1CCODE_WORLD = 0, |
| SSB_SPROM1CCODE_THAILAND, |
| SSB_SPROM1CCODE_ISRAEL, |
| SSB_SPROM1CCODE_JORDAN, |
| SSB_SPROM1CCODE_CHINA, |
| SSB_SPROM1CCODE_JAPAN, |
| SSB_SPROM1CCODE_USA_CANADA_ANZ, |
| SSB_SPROM1CCODE_EUROPE, |
| SSB_SPROM1CCODE_USA_LOW, |
| SSB_SPROM1CCODE_JAPAN_HIGH, |
| SSB_SPROM1CCODE_ALL, |
| SSB_SPROM1CCODE_NONE, |
| }; |
| |
| /* Address-Match values and masks (SSB_ADMATCHxxx) */ |
| #define SSB_ADM_TYPE 0x00000003 /* Address type */ |
| #define SSB_ADM_TYPE0 0 |
| #define SSB_ADM_TYPE1 1 |
| #define SSB_ADM_TYPE2 2 |
| #define SSB_ADM_AD64 0x00000004 |
| #define SSB_ADM_SZ0 0x000000F8 /* Type0 size */ |
| #define SSB_ADM_SZ0_SHIFT 3 |
| #define SSB_ADM_SZ1 0x000001F8 /* Type1 size */ |
| #define SSB_ADM_SZ1_SHIFT 3 |
| #define SSB_ADM_SZ2 0x000001F8 /* Type2 size */ |
| #define SSB_ADM_SZ2_SHIFT 3 |
| #define SSB_ADM_EN 0x00000400 /* Enable */ |
| #define SSB_ADM_NEG 0x00000800 /* Negative decode */ |
| #define SSB_ADM_BASE0 0xFFFFFF00 /* Type0 base address */ |
| #define SSB_ADM_BASE0_SHIFT 8 |
| #define SSB_ADM_BASE1 0xFFFFF000 /* Type1 base address for the core */ |
| #define SSB_ADM_BASE1_SHIFT 12 |
| #define SSB_ADM_BASE2 0xFFFF0000 /* Type2 base address for the core */ |
| #define SSB_ADM_BASE2_SHIFT 16 |
| |
| |
| #endif /* LINUX_SSB_REGS_H_ */ |