ath10k: add BMI parameters to fix calibration from DT/pre-cal
[ Upstream commit a9f5f287fa1d47d61dfa8b60f94831174b2ea4d0 ]
QCA99X0, QCA9888, QCA9984 supports calibration data in
either OTP or DT/pre-cal file. Current ath10k supports
Calibration data from OTP only.
If caldata is loaded from DT/pre-cal file, fetching board id
and applying calibration parameters like tx power gets failed.
error log:
[ 15.733663] ath10k_pci 0000:01:00.0: failed to fetch board file: -2
[ 15.741474] ath10k_pci 0000:01:00.0: could not probe fw (-2)
This patch adds calibration data support from DT/pre-cal
file. Below parameters are used to get board id and
applying calibration parameters from cal data.
EEPROM[OTP] FLASH[DT/pre-cal file]
Cal param 0x700 0x10000
Board id 0x10 0x8000
Tested on QCA9888 with pre-cal file.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/drivers/net/wireless/ath/ath10k/bmi.h b/drivers/net/wireless/ath/ath10k/bmi.h
index 7d3231a..82bdec7 100644
--- a/drivers/net/wireless/ath/ath10k/bmi.h
+++ b/drivers/net/wireless/ath/ath10k/bmi.h
@@ -83,6 +83,8 @@
#define BMI_NVRAM_SEG_NAME_SZ 16
#define BMI_PARAM_GET_EEPROM_BOARD_ID 0x10
+#define BMI_PARAM_GET_FLASH_BOARD_ID 0x8000
+#define BMI_PARAM_FLASH_SECTION_ALL 0x10000
#define ATH10K_BMI_BOARD_ID_FROM_OTP_MASK 0x7c00
#define ATH10K_BMI_BOARD_ID_FROM_OTP_LSB 10
diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 7b3017f..65ad7a1 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -652,7 +652,7 @@
{
u32 result, address;
u8 board_id, chip_id;
- int ret;
+ int ret, bmi_board_id_param;
address = ar->hw_params.patch_load_addr;
@@ -676,8 +676,13 @@
return ret;
}
- ret = ath10k_bmi_execute(ar, address, BMI_PARAM_GET_EEPROM_BOARD_ID,
- &result);
+ if (ar->cal_mode == ATH10K_PRE_CAL_MODE_DT ||
+ ar->cal_mode == ATH10K_PRE_CAL_MODE_FILE)
+ bmi_board_id_param = BMI_PARAM_GET_FLASH_BOARD_ID;
+ else
+ bmi_board_id_param = BMI_PARAM_GET_EEPROM_BOARD_ID;
+
+ ret = ath10k_bmi_execute(ar, address, bmi_board_id_param, &result);
if (ret) {
ath10k_err(ar, "could not execute otp for board id check: %d\n",
ret);
@@ -739,6 +744,11 @@
return ret;
}
+ /* As of now pre-cal is valid for 10_4 variants */
+ if (ar->cal_mode == ATH10K_PRE_CAL_MODE_DT ||
+ ar->cal_mode == ATH10K_PRE_CAL_MODE_FILE)
+ bmi_otp_exe_param = BMI_PARAM_FLASH_SECTION_ALL;
+
ret = ath10k_bmi_execute(ar, address, bmi_otp_exe_param, &result);
if (ret) {
ath10k_err(ar, "could not execute otp (%d)\n", ret);