ath10k: add wmi interface for pdev_get_temperature
Add WMI command support for reading temperature from the target and
corresponding WMI temperature event handler. The pdev_get_temperature
command is currently supported in 10.2 firmware alone.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c
index 77bb331..c2d7ac3 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.c
+++ b/drivers/net/wireless/ath/ath10k/wmi.c
@@ -145,6 +145,7 @@
.force_fw_hang_cmdid = WMI_FORCE_FW_HANG_CMDID,
.gpio_config_cmdid = WMI_GPIO_CONFIG_CMDID,
.gpio_output_cmdid = WMI_GPIO_OUTPUT_CMDID,
+ .pdev_get_temperature_cmdid = WMI_CMD_UNSUPPORTED,
};
/* 10.X WMI cmd track */
@@ -267,6 +268,7 @@
.force_fw_hang_cmdid = WMI_CMD_UNSUPPORTED,
.gpio_config_cmdid = WMI_10X_GPIO_CONFIG_CMDID,
.gpio_output_cmdid = WMI_10X_GPIO_OUTPUT_CMDID,
+ .pdev_get_temperature_cmdid = WMI_CMD_UNSUPPORTED,
};
/* 10.2.4 WMI cmd track */
@@ -388,6 +390,7 @@
.force_fw_hang_cmdid = WMI_CMD_UNSUPPORTED,
.gpio_config_cmdid = WMI_10_2_GPIO_CONFIG_CMDID,
.gpio_output_cmdid = WMI_10_2_GPIO_OUTPUT_CMDID,
+ .pdev_get_temperature_cmdid = WMI_10_2_PDEV_GET_TEMPERATURE_CMDID,
};
/* MAIN WMI VDEV param map */
@@ -843,6 +846,7 @@
.force_fw_hang_cmdid = WMI_CMD_UNSUPPORTED,
.gpio_config_cmdid = WMI_10_2_GPIO_CONFIG_CMDID,
.gpio_output_cmdid = WMI_10_2_GPIO_OUTPUT_CMDID,
+ .pdev_get_temperature_cmdid = WMI_CMD_UNSUPPORTED,
};
void ath10k_wmi_put_wmi_channel(struct wmi_channel *ch,
@@ -3026,6 +3030,17 @@
return 0;
}
+static int ath10k_wmi_event_temperature(struct ath10k *ar, struct sk_buff *skb)
+{
+ const struct wmi_pdev_temperature_event *ev;
+
+ ev = (struct wmi_pdev_temperature_event *)skb->data;
+ if (WARN_ON(skb->len < sizeof(*ev)))
+ return -EPROTO;
+
+ return 0;
+}
+
static void ath10k_wmi_op_rx(struct ath10k *ar, struct sk_buff *skb)
{
struct wmi_cmd_hdr *cmd_hdr;
@@ -3365,6 +3380,9 @@
case WMI_10_2_READY_EVENTID:
ath10k_wmi_event_ready(ar, skb);
break;
+ case WMI_10_2_PDEV_TEMPERATURE_EVENTID:
+ ath10k_wmi_event_temperature(ar, skb);
+ break;
case WMI_10_2_RTT_KEEPALIVE_EVENTID:
case WMI_10_2_GPIO_INPUT_EVENTID:
case WMI_10_2_PEER_RATECODE_LIST_EVENTID:
@@ -4646,6 +4664,19 @@
return skb;
}
+static struct sk_buff *
+ath10k_wmi_10_2_op_gen_pdev_get_temperature(struct ath10k *ar)
+{
+ struct sk_buff *skb;
+
+ skb = ath10k_wmi_alloc_skb(ar, 0);
+ if (!skb)
+ return ERR_PTR(-ENOMEM);
+
+ ath10k_dbg(ar, ATH10K_DBG_WMI, "wmi pdev get temperature\n");
+ return skb;
+}
+
/* This function assumes the beacon is already DMA mapped */
static struct sk_buff *
ath10k_wmi_op_gen_beacon_dma(struct ath10k_vif *arvif)
@@ -4895,6 +4926,7 @@
.gen_pktlog_enable = ath10k_wmi_op_gen_pktlog_enable,
.gen_pktlog_disable = ath10k_wmi_op_gen_pktlog_disable,
.gen_pdev_set_quiet_mode = ath10k_wmi_op_gen_pdev_set_quiet_mode,
+ /* .gen_pdev_get_temperature not implemented */
};
static const struct wmi_ops wmi_10_1_ops = {
@@ -4906,6 +4938,7 @@
.gen_pdev_set_rd = ath10k_wmi_10x_op_gen_pdev_set_rd,
.gen_start_scan = ath10k_wmi_10x_op_gen_start_scan,
.gen_peer_assoc = ath10k_wmi_10_1_op_gen_peer_assoc,
+ /* .gen_pdev_get_temperature not implemented */
/* shared with main branch */
.pull_scan = ath10k_wmi_op_pull_scan_ev,
@@ -4954,6 +4987,7 @@
.rx = ath10k_wmi_10_2_op_rx,
.gen_init = ath10k_wmi_10_2_op_gen_init,
.gen_peer_assoc = ath10k_wmi_10_2_op_gen_peer_assoc,
+ /* .gen_pdev_get_temperature not implemented */
/* shared with 10.1 */
.map_svc = wmi_10x_svc_map,
@@ -5008,6 +5042,7 @@
.rx = ath10k_wmi_10_2_op_rx,
.gen_init = ath10k_wmi_10_2_op_gen_init,
.gen_peer_assoc = ath10k_wmi_10_2_op_gen_peer_assoc,
+ .gen_pdev_get_temperature = ath10k_wmi_10_2_op_gen_pdev_get_temperature,
/* shared with 10.1 */
.map_svc = wmi_10x_svc_map,