blob: dfe6d9527efb4b6489676468d495e56e7841b2a9 [file] [log] [blame]
/* tmp401.c
*
* Copyright (C) 2007,2008 Hans de Goede <hdegoede@redhat.com>
* Preliminary tmp411 support by:
* Gabriel Konat, Sander Leget, Wouter Willems
* Copyright (C) 2009 Andre Prendel <andre.prendel@gmx.de>
*
* Cleanup and support for TMP431 and TMP432 by Guenter Roeck
* Copyright (c) 2013 Guenter Roeck <linux@roeck-us.net>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
/*
* Driver for the Texas Instruments TMP401 SMBUS temperature sensor IC.
*
* Note this IC is in some aspect similar to the LM90, but it has quite a
* few differences too, for example the local temp has a higher resolution
* and thus has 16 bits registers for its value and limit instead of 8 bits.
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/bitops.h>
#include <linux/slab.h>
#include <linux/jiffies.h>
#include <linux/i2c.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/err.h>
#include <linux/mutex.h>
#include <linux/sysfs.h>
/* Addresses to scan */
static const unsigned short normal_i2c[] = { 0x4c, 0x4d, 0x4e, I2C_CLIENT_END };
enum chips { tmp401, tmp411, tmp431, tmp432 };
/*
* The TMP401 registers, note some registers have different addresses for
* reading and writing
*/
#define TMP401_STATUS 0x02
#define TMP401_CONFIG_READ 0x03
#define TMP401_CONFIG_WRITE 0x09
#define TMP401_CONVERSION_RATE_READ 0x04
#define TMP401_CONVERSION_RATE_WRITE 0x0A
#define TMP401_TEMP_CRIT_HYST 0x21
#define TMP401_MANUFACTURER_ID_REG 0xFE
#define TMP401_DEVICE_ID_REG 0xFF
static const u8 TMP401_TEMP_MSB_READ[6][2] = {
{ 0x00, 0x01 }, /* temp */
{ 0x06, 0x08 }, /* low limit */
{ 0x05, 0x07 }, /* high limit */
{ 0x20, 0x19 }, /* therm (crit) limit */
{ 0x30, 0x34 }, /* lowest */
{ 0x32, 0x36 }, /* highest */
};
static const u8 TMP401_TEMP_MSB_WRITE[6][2] = {
{ 0, 0 }, /* temp (unused) */
{ 0x0C, 0x0E }, /* low limit */
{ 0x0B, 0x0D }, /* high limit */
{ 0x20, 0x19 }, /* therm (crit) limit */
{ 0x30, 0x34 }, /* lowest */
{ 0x32, 0x36 }, /* highest */
};
static const u8 TMP401_TEMP_LSB[6][2] = {
{ 0x15, 0x10 }, /* temp */
{ 0x17, 0x14 }, /* low limit */
{ 0x16, 0x13 }, /* high limit */
{ 0, 0 }, /* therm (crit) limit (unused) */
{ 0x31, 0x35 }, /* lowest */
{ 0x33, 0x37 }, /* highest */
};
static const u8 TMP432_TEMP_MSB_READ[4][3] = {
{ 0x00, 0x01, 0x23 }, /* temp */
{ 0x06, 0x08, 0x16 }, /* low limit */
{ 0x05, 0x07, 0x15 }, /* high limit */
{ 0x20, 0x19, 0x1A }, /* therm (crit) limit */
};
static const u8 TMP432_TEMP_MSB_WRITE[4][3] = {
{ 0, 0, 0 }, /* temp - unused */
{ 0x0C, 0x0E, 0x16 }, /* low limit */
{ 0x0B, 0x0D, 0x15 }, /* high limit */
{ 0x20, 0x19, 0x1A }, /* therm (crit) limit */
};
static const u8 TMP432_TEMP_LSB[3][3] = {
{ 0x29, 0x10, 0x24 }, /* temp */
{ 0x3E, 0x14, 0x18 }, /* low limit */
{ 0x3D, 0x13, 0x17 }, /* high limit */
};
/* [0] = fault, [1] = low, [2] = high, [3] = therm/crit */
static const u8 TMP432_STATUS_REG[] = {
0x1b, 0x36, 0x35, 0x37 };
/* Flags */
#define TMP401_CONFIG_RANGE BIT(2)
#define TMP401_CONFIG_SHUTDOWN BIT(6)
#define TMP401_STATUS_LOCAL_CRIT BIT(0)
#define TMP401_STATUS_REMOTE_CRIT BIT(1)
#define TMP401_STATUS_REMOTE_OPEN BIT(2)
#define TMP401_STATUS_REMOTE_LOW BIT(3)
#define TMP401_STATUS_REMOTE_HIGH BIT(4)
#define TMP401_STATUS_LOCAL_LOW BIT(5)
#define TMP401_STATUS_LOCAL_HIGH BIT(6)
/* On TMP432, each status has its own register */
#define TMP432_STATUS_LOCAL BIT(0)
#define TMP432_STATUS_REMOTE1 BIT(1)
#define TMP432_STATUS_REMOTE2 BIT(2)
/* Manufacturer / Device ID's */
#define TMP401_MANUFACTURER_ID 0x55
#define TMP401_DEVICE_ID 0x11
#define TMP411A_DEVICE_ID 0x12
#define TMP411B_DEVICE_ID 0x13
#define TMP411C_DEVICE_ID 0x10
#define TMP431_DEVICE_ID 0x31
#define TMP432_DEVICE_ID 0x32
/*
* Driver data (common to all clients)
*/
static const struct i2c_device_id tmp401_id[] = {
{ "tmp401", tmp401 },
{ "tmp411", tmp411 },
{ "tmp431", tmp431 },
{ "tmp432", tmp432 },
{ }
};
MODULE_DEVICE_TABLE(i2c, tmp401_id);
/*
* Client data (each client gets its own)
*/
struct tmp401_data {
struct device *hwmon_dev;
struct mutex update_lock;
char valid; /* zero until following fields are valid */
unsigned long last_updated; /* in jiffies */
enum chips kind;
unsigned int update_interval; /* in milliseconds */
/* register values */
u8 status[4];
u8 config;
u16 temp[6][3];
u8 temp_crit_hyst;
};
/*
* Sysfs attr show / store functions
*/
static int tmp401_register_to_temp(u16 reg, u8 config)
{
int temp = reg;
if (config & TMP401_CONFIG_RANGE)
temp -= 64 * 256;
return DIV_ROUND_CLOSEST(temp * 125, 32);
}
static u16 tmp401_temp_to_register(long temp, u8 config, int zbits)
{
if (config & TMP401_CONFIG_RANGE) {
temp = clamp_val(temp, -64000, 191000);
temp += 64000;
} else
temp = clamp_val(temp, 0, 127000);
return DIV_ROUND_CLOSEST(temp * (1 << (8 - zbits)), 1000) << zbits;
}
static int tmp401_update_device_reg16(struct i2c_client *client,
struct tmp401_data *data)
{
int i, j, val;
int num_regs = data->kind == tmp411 ? 6 : 4;
int num_sensors = data->kind == tmp432 ? 3 : 2;
for (i = 0; i < num_sensors; i++) { /* local / r1 / r2 */
for (j = 0; j < num_regs; j++) { /* temp / low / ... */
u8 regaddr;
/*
* High byte must be read first immediately followed
* by the low byte
*/
regaddr = data->kind == tmp432 ?
TMP432_TEMP_MSB_READ[j][i] :
TMP401_TEMP_MSB_READ[j][i];
val = i2c_smbus_read_byte_data(client, regaddr);
if (val < 0)
return val;
data->temp[j][i] = val << 8;
if (j == 3) /* crit is msb only */
continue;
regaddr = data->kind == tmp432 ? TMP432_TEMP_LSB[j][i]
: TMP401_TEMP_LSB[j][i];
val = i2c_smbus_read_byte_data(client, regaddr);
if (val < 0)
return val;
data->temp[j][i] |= val;
}
}
return 0;
}
static struct tmp401_data *tmp401_update_device(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct tmp401_data *data = i2c_get_clientdata(client);
struct tmp401_data *ret = data;
int i, val;
unsigned long next_update;
mutex_lock(&data->update_lock);
next_update = data->last_updated +
msecs_to_jiffies(data->update_interval);
if (time_after(jiffies, next_update) || !data->valid) {
if (data->kind != tmp432) {
/*
* The driver uses the TMP432 status format internally.
* Convert status to TMP432 format for other chips.
*/
val = i2c_smbus_read_byte_data(client, TMP401_STATUS);
if (val < 0) {
ret = ERR_PTR(val);
goto abort;
}
data->status[0] =
(val & TMP401_STATUS_REMOTE_OPEN) >> 1;
data->status[1] =
((val & TMP401_STATUS_REMOTE_LOW) >> 2) |
((val & TMP401_STATUS_LOCAL_LOW) >> 5);
data->status[2] =
((val & TMP401_STATUS_REMOTE_HIGH) >> 3) |
((val & TMP401_STATUS_LOCAL_HIGH) >> 6);
data->status[3] = val & (TMP401_STATUS_LOCAL_CRIT
| TMP401_STATUS_REMOTE_CRIT);
} else {
for (i = 0; i < ARRAY_SIZE(data->status); i++) {
val = i2c_smbus_read_byte_data(client,
TMP432_STATUS_REG[i]);
if (val < 0) {
ret = ERR_PTR(val);
goto abort;
}
data->status[i] = val;
}
}
val = i2c_smbus_read_byte_data(client, TMP401_CONFIG_READ);
if (val < 0) {
ret = ERR_PTR(val);
goto abort;
}
data->config = val;
val = tmp401_update_device_reg16(client, data);
if (val < 0) {
ret = ERR_PTR(val);
goto abort;
}
val = i2c_smbus_read_byte_data(client, TMP401_TEMP_CRIT_HYST);
if (val < 0) {
ret = ERR_PTR(val);
goto abort;
}
data->temp_crit_hyst = val;
data->last_updated = jiffies;
data->valid = 1;
}
abort:
mutex_unlock(&data->update_lock);
return ret;
}
static ssize_t show_temp(struct device *dev,
struct device_attribute *devattr, char *buf)
{
int nr = to_sensor_dev_attr_2(devattr)->nr;
int index = to_sensor_dev_attr_2(devattr)->index;
struct tmp401_data *data = tmp401_update_device(dev);
if (IS_ERR(data))
return PTR_ERR(data);
return sprintf(buf, "%d\n",
tmp401_register_to_temp(data->temp[nr][index], data->config));
}
static ssize_t show_temp_crit_hyst(struct device *dev,
struct device_attribute *devattr, char *buf)
{
int temp, index = to_sensor_dev_attr(devattr)->index;
struct tmp401_data *data = tmp401_update_device(dev);
if (IS_ERR(data))
return PTR_ERR(data);
mutex_lock(&data->update_lock);
temp = tmp401_register_to_temp(data->temp[3][index], data->config);
temp -= data->temp_crit_hyst * 1000;
mutex_unlock(&data->update_lock);
return sprintf(buf, "%d\n", temp);
}
static ssize_t show_status(struct device *dev,
struct device_attribute *devattr, char *buf)
{
int nr = to_sensor_dev_attr_2(devattr)->nr;
int mask = to_sensor_dev_attr_2(devattr)->index;
struct tmp401_data *data = tmp401_update_device(dev);
if (IS_ERR(data))
return PTR_ERR(data);
return sprintf(buf, "%d\n", !!(data->status[nr] & mask));
}
static ssize_t store_temp(struct device *dev, struct device_attribute *devattr,
const char *buf, size_t count)
{
int nr = to_sensor_dev_attr_2(devattr)->nr;
int index = to_sensor_dev_attr_2(devattr)->index;
struct i2c_client *client = to_i2c_client(dev);
struct tmp401_data *data = tmp401_update_device(dev);
long val;
u16 reg;
u8 regaddr;
if (IS_ERR(data))
return PTR_ERR(data);
if (kstrtol(buf, 10, &val))
return -EINVAL;
reg = tmp401_temp_to_register(val, data->config, nr == 3 ? 8 : 4);
mutex_lock(&data->update_lock);
regaddr = data->kind == tmp432 ? TMP432_TEMP_MSB_WRITE[nr][index]
: TMP401_TEMP_MSB_WRITE[nr][index];
i2c_smbus_write_byte_data(client, regaddr, reg >> 8);
if (nr != 3) {
regaddr = data->kind == tmp432 ? TMP432_TEMP_LSB[nr][index]
: TMP401_TEMP_LSB[nr][index];
i2c_smbus_write_byte_data(client, regaddr, reg & 0xFF);
}
data->temp[nr][index] = reg;
mutex_unlock(&data->update_lock);
return count;
}
static ssize_t store_temp_crit_hyst(struct device *dev, struct device_attribute
*devattr, const char *buf, size_t count)
{
int temp, index = to_sensor_dev_attr(devattr)->index;
struct tmp401_data *data = tmp401_update_device(dev);
long val;
u8 reg;
if (IS_ERR(data))
return PTR_ERR(data);
if (kstrtol(buf, 10, &val))
return -EINVAL;
if (data->config & TMP401_CONFIG_RANGE)
val = clamp_val(val, -64000, 191000);
else
val = clamp_val(val, 0, 127000);
mutex_lock(&data->update_lock);
temp = tmp401_register_to_temp(data->temp[3][index], data->config);
val = clamp_val(val, temp - 255000, temp);
reg = ((temp - val) + 500) / 1000;
i2c_smbus_write_byte_data(to_i2c_client(dev), TMP401_TEMP_CRIT_HYST,
reg);
data->temp_crit_hyst = reg;
mutex_unlock(&data->update_lock);
return count;
}
/*
* Resets the historical measurements of minimum and maximum temperatures.
* This is done by writing any value to any of the minimum/maximum registers
* (0x30-0x37).
*/
static ssize_t reset_temp_history(struct device *dev,
struct device_attribute *devattr, const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct tmp401_data *data = i2c_get_clientdata(client);
long val;
if (kstrtol(buf, 10, &val))
return -EINVAL;
if (val != 1) {
dev_err(dev,
"temp_reset_history value %ld not supported. Use 1 to reset the history!\n",
val);
return -EINVAL;
}
mutex_lock(&data->update_lock);
i2c_smbus_write_byte_data(client, TMP401_TEMP_MSB_WRITE[5][0], val);
data->valid = 0;
mutex_unlock(&data->update_lock);
return count;
}
static ssize_t show_update_interval(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct i2c_client *client = to_i2c_client(dev);
struct tmp401_data *data = i2c_get_clientdata(client);
return sprintf(buf, "%u\n", data->update_interval);
}
static ssize_t set_update_interval(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct tmp401_data *data = i2c_get_clientdata(client);
unsigned long val;
int err, rate;
err = kstrtoul(buf, 10, &val);
if (err)
return err;
/*
* For valid rates, interval can be calculated as
* interval = (1 << (7 - rate)) * 125;
* Rounded rate is therefore
* rate = 7 - __fls(interval * 4 / (125 * 3));
* Use clamp_val() to avoid overflows, and to ensure valid input
* for __fls.
*/
val = clamp_val(val, 125, 16000);
rate = 7 - __fls(val * 4 / (125 * 3));
mutex_lock(&data->update_lock);
i2c_smbus_write_byte_data(client, TMP401_CONVERSION_RATE_WRITE, rate);
data->update_interval = (1 << (7 - rate)) * 125;
mutex_unlock(&data->update_lock);
return count;
}
static SENSOR_DEVICE_ATTR_2(temp1_input, S_IRUGO, show_temp, NULL, 0, 0);
static SENSOR_DEVICE_ATTR_2(temp1_min, S_IWUSR | S_IRUGO, show_temp,
store_temp, 1, 0);
static SENSOR_DEVICE_ATTR_2(temp1_max, S_IWUSR | S_IRUGO, show_temp,
store_temp, 2, 0);
static SENSOR_DEVICE_ATTR_2(temp1_crit, S_IWUSR | S_IRUGO, show_temp,
store_temp, 3, 0);
static SENSOR_DEVICE_ATTR(temp1_crit_hyst, S_IWUSR | S_IRUGO,
show_temp_crit_hyst, store_temp_crit_hyst, 0);
static SENSOR_DEVICE_ATTR_2(temp1_min_alarm, S_IRUGO, show_status, NULL,
1, TMP432_STATUS_LOCAL);
static SENSOR_DEVICE_ATTR_2(temp1_max_alarm, S_IRUGO, show_status, NULL,
2, TMP432_STATUS_LOCAL);
static SENSOR_DEVICE_ATTR_2(temp1_crit_alarm, S_IRUGO, show_status, NULL,
3, TMP432_STATUS_LOCAL);
static SENSOR_DEVICE_ATTR_2(temp2_input, S_IRUGO, show_temp, NULL, 0, 1);
static SENSOR_DEVICE_ATTR_2(temp2_min, S_IWUSR | S_IRUGO, show_temp,
store_temp, 1, 1);
static SENSOR_DEVICE_ATTR_2(temp2_max, S_IWUSR | S_IRUGO, show_temp,
store_temp, 2, 1);
static SENSOR_DEVICE_ATTR_2(temp2_crit, S_IWUSR | S_IRUGO, show_temp,
store_temp, 3, 1);
static SENSOR_DEVICE_ATTR(temp2_crit_hyst, S_IRUGO, show_temp_crit_hyst,
NULL, 1);
static SENSOR_DEVICE_ATTR_2(temp2_fault, S_IRUGO, show_status, NULL,
0, TMP432_STATUS_REMOTE1);
static SENSOR_DEVICE_ATTR_2(temp2_min_alarm, S_IRUGO, show_status, NULL,
1, TMP432_STATUS_REMOTE1);
static SENSOR_DEVICE_ATTR_2(temp2_max_alarm, S_IRUGO, show_status, NULL,
2, TMP432_STATUS_REMOTE1);
static SENSOR_DEVICE_ATTR_2(temp2_crit_alarm, S_IRUGO, show_status, NULL,
3, TMP432_STATUS_REMOTE1);
static DEVICE_ATTR(update_interval, S_IRUGO | S_IWUSR, show_update_interval,
set_update_interval);
static struct attribute *tmp401_attributes[] = {
&sensor_dev_attr_temp1_input.dev_attr.attr,
&sensor_dev_attr_temp1_min.dev_attr.attr,
&sensor_dev_attr_temp1_max.dev_attr.attr,
&sensor_dev_attr_temp1_crit.dev_attr.attr,
&sensor_dev_attr_temp1_crit_hyst.dev_attr.attr,
&sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
&sensor_dev_attr_temp1_min_alarm.dev_attr.attr,
&sensor_dev_attr_temp1_crit_alarm.dev_attr.attr,
&sensor_dev_attr_temp2_input.dev_attr.attr,
&sensor_dev_attr_temp2_min.dev_attr.attr,
&sensor_dev_attr_temp2_max.dev_attr.attr,
&sensor_dev_attr_temp2_crit.dev_attr.attr,
&sensor_dev_attr_temp2_crit_hyst.dev_attr.attr,
&sensor_dev_attr_temp2_fault.dev_attr.attr,
&sensor_dev_attr_temp2_max_alarm.dev_attr.attr,
&sensor_dev_attr_temp2_min_alarm.dev_attr.attr,
&sensor_dev_attr_temp2_crit_alarm.dev_attr.attr,
&dev_attr_update_interval.attr,
NULL
};
static const struct attribute_group tmp401_group = {
.attrs = tmp401_attributes,
};
/*
* Additional features of the TMP411 chip.
* The TMP411 stores the minimum and maximum
* temperature measured since power-on, chip-reset, or
* minimum and maximum register reset for both the local
* and remote channels.
*/
static SENSOR_DEVICE_ATTR_2(temp1_lowest, S_IRUGO, show_temp, NULL, 4, 0);
static SENSOR_DEVICE_ATTR_2(temp1_highest, S_IRUGO, show_temp, NULL, 5, 0);
static SENSOR_DEVICE_ATTR_2(temp2_lowest, S_IRUGO, show_temp, NULL, 4, 1);
static SENSOR_DEVICE_ATTR_2(temp2_highest, S_IRUGO, show_temp, NULL, 5, 1);
static SENSOR_DEVICE_ATTR(temp_reset_history, S_IWUSR, NULL, reset_temp_history,
0);
static struct attribute *tmp411_attributes[] = {
&sensor_dev_attr_temp1_highest.dev_attr.attr,
&sensor_dev_attr_temp1_lowest.dev_attr.attr,
&sensor_dev_attr_temp2_highest.dev_attr.attr,
&sensor_dev_attr_temp2_lowest.dev_attr.attr,
&sensor_dev_attr_temp_reset_history.dev_attr.attr,
NULL
};
static const struct attribute_group tmp411_group = {
.attrs = tmp411_attributes,
};
static SENSOR_DEVICE_ATTR_2(temp3_input, S_IRUGO, show_temp, NULL, 0, 2);
static SENSOR_DEVICE_ATTR_2(temp3_min, S_IWUSR | S_IRUGO, show_temp,
store_temp, 1, 2);
static SENSOR_DEVICE_ATTR_2(temp3_max, S_IWUSR | S_IRUGO, show_temp,
store_temp, 2, 2);
static SENSOR_DEVICE_ATTR_2(temp3_crit, S_IWUSR | S_IRUGO, show_temp,
store_temp, 3, 2);
static SENSOR_DEVICE_ATTR(temp3_crit_hyst, S_IRUGO, show_temp_crit_hyst,
NULL, 2);
static SENSOR_DEVICE_ATTR_2(temp3_fault, S_IRUGO, show_status, NULL,
0, TMP432_STATUS_REMOTE2);
static SENSOR_DEVICE_ATTR_2(temp3_min_alarm, S_IRUGO, show_status, NULL,
1, TMP432_STATUS_REMOTE2);
static SENSOR_DEVICE_ATTR_2(temp3_max_alarm, S_IRUGO, show_status, NULL,
2, TMP432_STATUS_REMOTE2);
static SENSOR_DEVICE_ATTR_2(temp3_crit_alarm, S_IRUGO, show_status, NULL,
3, TMP432_STATUS_REMOTE2);
static struct attribute *tmp432_attributes[] = {
&sensor_dev_attr_temp3_input.dev_attr.attr,
&sensor_dev_attr_temp3_min.dev_attr.attr,
&sensor_dev_attr_temp3_max.dev_attr.attr,
&sensor_dev_attr_temp3_crit.dev_attr.attr,
&sensor_dev_attr_temp3_crit_hyst.dev_attr.attr,
&sensor_dev_attr_temp3_fault.dev_attr.attr,
&sensor_dev_attr_temp3_max_alarm.dev_attr.attr,
&sensor_dev_attr_temp3_min_alarm.dev_attr.attr,
&sensor_dev_attr_temp3_crit_alarm.dev_attr.attr,
NULL
};
static const struct attribute_group tmp432_group = {
.attrs = tmp432_attributes,
};
/*
* Begin non sysfs callback code (aka Real code)
*/
static void tmp401_init_client(struct i2c_client *client)
{
int config, config_orig;
struct tmp401_data *data = i2c_get_clientdata(client);
/* Set the conversion rate to 2 Hz */
i2c_smbus_write_byte_data(client, TMP401_CONVERSION_RATE_WRITE, 5);
data->update_interval = 500;
/* Start conversions (disable shutdown if necessary) */
config = i2c_smbus_read_byte_data(client, TMP401_CONFIG_READ);
if (config < 0) {
dev_warn(&client->dev, "Initialization failed!\n");
return;
}
config_orig = config;
config &= ~TMP401_CONFIG_SHUTDOWN;
if (config != config_orig)
i2c_smbus_write_byte_data(client, TMP401_CONFIG_WRITE, config);
}
static int tmp401_detect(struct i2c_client *client,
struct i2c_board_info *info)
{
enum chips kind;
struct i2c_adapter *adapter = client->adapter;
u8 reg;
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
return -ENODEV;
/* Detect and identify the chip */
reg = i2c_smbus_read_byte_data(client, TMP401_MANUFACTURER_ID_REG);
if (reg != TMP401_MANUFACTURER_ID)
return -ENODEV;
reg = i2c_smbus_read_byte_data(client, TMP401_DEVICE_ID_REG);
switch (reg) {
case TMP401_DEVICE_ID:
if (client->addr != 0x4c)
return -ENODEV;
kind = tmp401;
break;
case TMP411A_DEVICE_ID:
if (client->addr != 0x4c)
return -ENODEV;
kind = tmp411;
break;
case TMP411B_DEVICE_ID:
if (client->addr != 0x4d)
return -ENODEV;
kind = tmp411;
break;
case TMP411C_DEVICE_ID:
if (client->addr != 0x4e)
return -ENODEV;
kind = tmp411;
break;
case TMP431_DEVICE_ID:
if (client->addr == 0x4e)
return -ENODEV;
kind = tmp431;
break;
case TMP432_DEVICE_ID:
if (client->addr == 0x4e)
return -ENODEV;
kind = tmp432;
break;
default:
return -ENODEV;
}
reg = i2c_smbus_read_byte_data(client, TMP401_CONFIG_READ);
if (reg & 0x1b)
return -ENODEV;
reg = i2c_smbus_read_byte_data(client, TMP401_CONVERSION_RATE_READ);
/* Datasheet says: 0x1-0x6 */
if (reg > 15)
return -ENODEV;
strlcpy(info->type, tmp401_id[kind].name, I2C_NAME_SIZE);
return 0;
}
static int tmp401_remove(struct i2c_client *client)
{
struct device *dev = &client->dev;
struct tmp401_data *data = i2c_get_clientdata(client);
if (data->hwmon_dev)
hwmon_device_unregister(data->hwmon_dev);
sysfs_remove_group(&dev->kobj, &tmp401_group);
if (data->kind == tmp411)
sysfs_remove_group(&dev->kobj, &tmp411_group);
if (data->kind == tmp432)
sysfs_remove_group(&dev->kobj, &tmp432_group);
return 0;
}
static int tmp401_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct device *dev = &client->dev;
int err;
struct tmp401_data *data;
const char *names[] = { "TMP401", "TMP411", "TMP431", "TMP432" };
data = devm_kzalloc(dev, sizeof(struct tmp401_data), GFP_KERNEL);
if (!data)
return -ENOMEM;
i2c_set_clientdata(client, data);
mutex_init(&data->update_lock);
data->kind = id->driver_data;
/* Initialize the TMP401 chip */
tmp401_init_client(client);
/* Register sysfs hooks */
err = sysfs_create_group(&dev->kobj, &tmp401_group);
if (err)
return err;
/* Register additional tmp411 sysfs hooks */
if (data->kind == tmp411) {
err = sysfs_create_group(&dev->kobj, &tmp411_group);
if (err)
goto exit_remove;
}
/* Register additional tmp432 sysfs hooks */
if (data->kind == tmp432) {
err = sysfs_create_group(&dev->kobj, &tmp432_group);
if (err)
goto exit_remove;
}
data->hwmon_dev = hwmon_device_register(dev);
if (IS_ERR(data->hwmon_dev)) {
err = PTR_ERR(data->hwmon_dev);
data->hwmon_dev = NULL;
goto exit_remove;
}
dev_info(dev, "Detected TI %s chip\n", names[data->kind]);
return 0;
exit_remove:
tmp401_remove(client);
return err;
}
static struct i2c_driver tmp401_driver = {
.class = I2C_CLASS_HWMON,
.driver = {
.name = "tmp401",
},
.probe = tmp401_probe,
.remove = tmp401_remove,
.id_table = tmp401_id,
.detect = tmp401_detect,
.address_list = normal_i2c,
};
module_i2c_driver(tmp401_driver);
MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>");
MODULE_DESCRIPTION("Texas Instruments TMP401 temperature sensor driver");
MODULE_LICENSE("GPL");