blob: 00835d537c102f3fb276f1073681f21aa94e3307 [file] [log] [blame]
/*======================================================================
An elsa_cs PCMCIA client driver
This driver is for the Elsa PCM ISDN Cards, i.e. the MicroLink
The contents of this file are subject to the Mozilla Public
License Version 1.1 (the "License"); you may not use this file
except in compliance with the License. You may obtain a copy of
the License at http://www.mozilla.org/MPL/
Software distributed under the License is distributed on an "AS
IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or
implied. See the License for the specific language governing
rights and limitations under the License.
The initial developer of the original code is David A. Hinds
<dahinds@users.sourceforge.net>. Portions created by David A. Hinds
are Copyright (C) 1999 David A. Hinds. All Rights Reserved.
Modifications from dummy_cs.c are Copyright (C) 1999-2001 Klaus
Lichtenwalder <Lichtenwalder@ACM.org>. All Rights Reserved.
Alternatively, the contents of this file may be used under the
terms of the GNU General Public License version 2 (the "GPL"), in
which case the provisions of the GPL are applicable instead of the
above. If you wish to allow the use of your version of this file
only under the terms of the GPL and not to allow others to use
your version of this file under the MPL, indicate your decision
by deleting the provisions above and replace them with the notice
and other provisions required by the GPL. If you do not delete
the provisions above, a recipient may use your version of this
file under either the MPL or the GPL.
======================================================================*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/sched.h>
#include <linux/ptrace.h>
#include <linux/slab.h>
#include <linux/string.h>
#include <linux/timer.h>
#include <linux/ioport.h>
#include <asm/io.h>
#include <asm/system.h>
#include <pcmcia/cs_types.h>
#include <pcmcia/cs.h>
#include <pcmcia/cistpl.h>
#include <pcmcia/cisreg.h>
#include <pcmcia/ds.h>
#include "hisax_cfg.h"
MODULE_DESCRIPTION("ISDN4Linux: PCMCIA client driver for Elsa PCM cards");
MODULE_AUTHOR("Klaus Lichtenwalder");
MODULE_LICENSE("Dual MPL/GPL");
/*
All the PCMCIA modules use PCMCIA_DEBUG to control debugging. If
you do not define PCMCIA_DEBUG at all, all the debug code will be
left out. If you compile with PCMCIA_DEBUG=0, the debug code will
be present but disabled -- but it can then be enabled for specific
modules at load time with a 'pc_debug=#' option to insmod.
*/
#ifdef PCMCIA_DEBUG
static int pc_debug = PCMCIA_DEBUG;
module_param(pc_debug, int, 0);
#define DEBUG(n, args...) if (pc_debug>(n)) printk(KERN_DEBUG args);
static char *version =
"elsa_cs.c $Revision: 1.2.2.4 $ $Date: 2004/01/25 15:07:06 $ (K.Lichtenwalder)";
#else
#define DEBUG(n, args...)
#endif
/*====================================================================*/
/* Parameters that can be set with 'insmod' */
static int protocol = 2; /* EURO-ISDN Default */
module_param(protocol, int, 0);
/*====================================================================*/
/*
The event() function is this driver's Card Services event handler.
It will be called by Card Services when an appropriate card status
event is received. The config() and release() entry points are
used to configure or release a socket, in response to card insertion
and ejection events. They are invoked from the elsa_cs event
handler.
*/
static void elsa_cs_config(dev_link_t *link);
static void elsa_cs_release(dev_link_t *link);
/*
The attach() and detach() entry points are used to create and destroy
"instances" of the driver, where each instance represents everything
needed to manage one actual PCMCIA card.
*/
static void elsa_cs_detach(struct pcmcia_device *p_dev);
/*
A driver needs to provide a dev_node_t structure for each device
on a card. In some cases, there is only one device per card (for
example, ethernet cards, modems). In other cases, there may be
many actual or logical devices (SCSI adapters, memory cards with
multiple partitions). The dev_node_t structures need to be kept
in a linked list starting at the 'dev' field of a dev_link_t
structure. We allocate them in the card's private data structure,
because they generally shouldn't be allocated dynamically.
In this case, we also provide a flag to indicate if a device is
"stopped" due to a power management event, or card ejection. The
device IO routines can use a flag like this to throttle IO to a
card that is not ready to accept it.
*/
typedef struct local_info_t {
dev_link_t link;
dev_node_t node;
int busy;
int cardnr;
} local_info_t;
/*======================================================================
elsa_cs_attach() creates an "instance" of the driver, allocatingx
local data structures for one device. The device is registered
with Card Services.
The dev_link structure is initialized, but we don't actually
configure the card at this point -- we wait until we receive a
card insertion event.
======================================================================*/
static int elsa_cs_attach(struct pcmcia_device *p_dev)
{
dev_link_t *link;
local_info_t *local;
DEBUG(0, "elsa_cs_attach()\n");
/* Allocate space for private device-specific data */
local = kmalloc(sizeof(local_info_t), GFP_KERNEL);
if (!local) return -ENOMEM;
memset(local, 0, sizeof(local_info_t));
local->cardnr = -1;
link = &local->link; link->priv = local;
/* Interrupt setup */
link->irq.Attributes = IRQ_TYPE_DYNAMIC_SHARING|IRQ_FIRST_SHARED;
link->irq.IRQInfo1 = IRQ_LEVEL_ID|IRQ_SHARE_ID;
link->irq.Handler = NULL;
/*
General socket configuration defaults can go here. In this
client, we assume very little, and rely on the CIS for almost
everything. In most clients, many details (i.e., number, sizes,
and attributes of IO windows) are fixed by the nature of the
device, and can be hard-wired here.
*/
link->io.NumPorts1 = 8;
link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
link->io.IOAddrLines = 3;
link->conf.Attributes = CONF_ENABLE_IRQ;
link->conf.IntType = INT_MEMORY_AND_IO;
link->handle = p_dev;
p_dev->instance = link;
link->state |= DEV_PRESENT | DEV_CONFIG_PENDING;
elsa_cs_config(link);
return 0;
} /* elsa_cs_attach */
/*======================================================================
This deletes a driver "instance". The device is de-registered
with Card Services. If it has been released, all local data
structures are freed. Otherwise, the structures will be freed
when the device is released.
======================================================================*/
static void elsa_cs_detach(struct pcmcia_device *p_dev)
{
dev_link_t *link = dev_to_instance(p_dev);
local_info_t *info = link->priv;
DEBUG(0, "elsa_cs_detach(0x%p)\n", link);
if (link->state & DEV_CONFIG) {
info->busy = 1;
elsa_cs_release(link);
}
kfree(info);
} /* elsa_cs_detach */
/*======================================================================
elsa_cs_config() is scheduled to run after a CARD_INSERTION event
is received, to configure the PCMCIA socket, and to make the
device available to the system.
======================================================================*/
static int get_tuple(client_handle_t handle, tuple_t *tuple,
cisparse_t *parse)
{
int i = pcmcia_get_tuple_data(handle, tuple);
if (i != CS_SUCCESS) return i;
return pcmcia_parse_tuple(handle, tuple, parse);
}
static int first_tuple(client_handle_t handle, tuple_t *tuple,
cisparse_t *parse)
{
int i = pcmcia_get_first_tuple(handle, tuple);
if (i != CS_SUCCESS) return i;
return get_tuple(handle, tuple, parse);
}
static int next_tuple(client_handle_t handle, tuple_t *tuple,
cisparse_t *parse)
{
int i = pcmcia_get_next_tuple(handle, tuple);
if (i != CS_SUCCESS) return i;
return get_tuple(handle, tuple, parse);
}
static void elsa_cs_config(dev_link_t *link)
{
client_handle_t handle;
tuple_t tuple;
cisparse_t parse;
local_info_t *dev;
int i, j, last_fn;
u_short buf[128];
cistpl_cftable_entry_t *cf = &parse.cftable_entry;
IsdnCard_t icard;
DEBUG(0, "elsa_config(0x%p)\n", link);
handle = link->handle;
dev = link->priv;
/*
This reads the card's CONFIG tuple to find its configuration
registers.
*/
tuple.DesiredTuple = CISTPL_CONFIG;
tuple.TupleData = (cisdata_t *)buf;
tuple.TupleDataMax = 255;
tuple.TupleOffset = 0;
tuple.Attributes = 0;
i = first_tuple(handle, &tuple, &parse);
if (i != CS_SUCCESS) {
last_fn = ParseTuple;
goto cs_failed;
}
link->conf.ConfigBase = parse.config.base;
link->conf.Present = parse.config.rmask[0];
/* Configure card */
link->state |= DEV_CONFIG;
tuple.TupleData = (cisdata_t *)buf;
tuple.TupleOffset = 0; tuple.TupleDataMax = 255;
tuple.Attributes = 0;
tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
i = first_tuple(handle, &tuple, &parse);
while (i == CS_SUCCESS) {
if ( (cf->io.nwin > 0) && cf->io.win[0].base) {
printk(KERN_INFO "(elsa_cs: looks like the 96 model)\n");
link->conf.ConfigIndex = cf->index;
link->io.BasePort1 = cf->io.win[0].base;
i = pcmcia_request_io(link->handle, &link->io);
if (i == CS_SUCCESS) break;
} else {
printk(KERN_INFO "(elsa_cs: looks like the 97 model)\n");
link->conf.ConfigIndex = cf->index;
for (i = 0, j = 0x2f0; j > 0x100; j -= 0x10) {
link->io.BasePort1 = j;
i = pcmcia_request_io(link->handle, &link->io);
if (i == CS_SUCCESS) break;
}
break;
}
i = next_tuple(handle, &tuple, &parse);
}
if (i != CS_SUCCESS) {
last_fn = RequestIO;
goto cs_failed;
}
i = pcmcia_request_irq(link->handle, &link->irq);
if (i != CS_SUCCESS) {
link->irq.AssignedIRQ = 0;
last_fn = RequestIRQ;
goto cs_failed;
}
i = pcmcia_request_configuration(link->handle, &link->conf);
if (i != CS_SUCCESS) {
last_fn = RequestConfiguration;
goto cs_failed;
}
/* At this point, the dev_node_t structure(s) should be
initialized and arranged in a linked list at link->dev. *//* */
sprintf(dev->node.dev_name, "elsa");
dev->node.major = dev->node.minor = 0x0;
link->dev = &dev->node;
/* Finally, report what we've done */
printk(KERN_INFO "%s: index 0x%02x: ",
dev->node.dev_name, link->conf.ConfigIndex);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %d", link->irq.AssignedIRQ);
if (link->io.NumPorts1)
printk(", io 0x%04x-0x%04x", link->io.BasePort1,
link->io.BasePort1+link->io.NumPorts1-1);
if (link->io.NumPorts2)
printk(" & 0x%04x-0x%04x", link->io.BasePort2,
link->io.BasePort2+link->io.NumPorts2-1);
printk("\n");
link->state &= ~DEV_CONFIG_PENDING;
icard.para[0] = link->irq.AssignedIRQ;
icard.para[1] = link->io.BasePort1;
icard.protocol = protocol;
icard.typ = ISDN_CTYPE_ELSA_PCMCIA;
i = hisax_init_pcmcia(link, &(((local_info_t*)link->priv)->busy), &icard);
if (i < 0) {
printk(KERN_ERR "elsa_cs: failed to initialize Elsa PCMCIA %d at i/o %#x\n",
i, link->io.BasePort1);
elsa_cs_release(link);
} else
((local_info_t*)link->priv)->cardnr = i;
return;
cs_failed:
cs_error(link->handle, last_fn, i);
elsa_cs_release(link);
} /* elsa_cs_config */
/*======================================================================
After a card is removed, elsa_cs_release() will unregister the net
device, and release the PCMCIA configuration. If the device is
still open, this will be postponed until it is closed.
======================================================================*/
static void elsa_cs_release(dev_link_t *link)
{
local_info_t *local = link->priv;
DEBUG(0, "elsa_cs_release(0x%p)\n", link);
if (local) {
if (local->cardnr >= 0) {
/* no unregister function with hisax */
HiSax_closecard(local->cardnr);
}
}
pcmcia_disable_device(link->handle);
} /* elsa_cs_release */
static int elsa_suspend(struct pcmcia_device *p_dev)
{
dev_link_t *link = dev_to_instance(p_dev);
local_info_t *dev = link->priv;
dev->busy = 1;
return 0;
}
static int elsa_resume(struct pcmcia_device *p_dev)
{
dev_link_t *link = dev_to_instance(p_dev);
local_info_t *dev = link->priv;
dev->busy = 0;
return 0;
}
static struct pcmcia_device_id elsa_ids[] = {
PCMCIA_DEVICE_PROD_ID12("ELSA AG (Aachen, Germany)", "MicroLink ISDN/MC ", 0x983de2c4, 0x333ba257),
PCMCIA_DEVICE_PROD_ID12("ELSA GmbH, Aachen", "MicroLink ISDN/MC ", 0x639e5718, 0x333ba257),
PCMCIA_DEVICE_NULL
};
MODULE_DEVICE_TABLE(pcmcia, elsa_ids);
static struct pcmcia_driver elsa_cs_driver = {
.owner = THIS_MODULE,
.drv = {
.name = "elsa_cs",
},
.probe = elsa_cs_attach,
.remove = elsa_cs_detach,
.id_table = elsa_ids,
.suspend = elsa_suspend,
.resume = elsa_resume,
};
static int __init init_elsa_cs(void)
{
return pcmcia_register_driver(&elsa_cs_driver);
}
static void __exit exit_elsa_cs(void)
{
pcmcia_unregister_driver(&elsa_cs_driver);
}
module_init(init_elsa_cs);
module_exit(exit_elsa_cs);