[libata] use dev_printk() throughout drivers
A few drivers were not following the standard meme of printing out
their driver name and version at module load time; this is fixed
as well.
diff --git a/drivers/scsi/sata_via.c b/drivers/scsi/sata_via.c
index 80e291a..b3ecdbe 100644
--- a/drivers/scsi/sata_via.c
+++ b/drivers/scsi/sata_via.c
@@ -41,6 +41,7 @@
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
+#include <linux/device.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include <linux/libata.h>
@@ -259,15 +260,15 @@
u8 tmp8;
pci_read_config_byte(pdev, PCI_INTERRUPT_LINE, &tmp8);
- printk(KERN_INFO DRV_NAME "(%s): routed to hard irq line %d\n",
- pci_name(pdev),
+ dev_printk(KERN_INFO, &pdev->dev, "routed to hard irq line %d\n",
(int) (tmp8 & 0xf0) == 0xf0 ? 0 : tmp8 & 0x0f);
/* make sure SATA channels are enabled */
pci_read_config_byte(pdev, SATA_CHAN_ENAB, &tmp8);
if ((tmp8 & ALL_PORTS) != ALL_PORTS) {
- printk(KERN_DEBUG DRV_NAME "(%s): enabling SATA channels (0x%x)\n",
- pci_name(pdev), (int) tmp8);
+ dev_printk(KERN_DEBUG, &pdev->dev,
+ "enabling SATA channels (0x%x)\n",
+ (int) tmp8);
tmp8 |= ALL_PORTS;
pci_write_config_byte(pdev, SATA_CHAN_ENAB, tmp8);
}
@@ -275,8 +276,9 @@
/* make sure interrupts for each channel sent to us */
pci_read_config_byte(pdev, SATA_INT_GATE, &tmp8);
if ((tmp8 & ALL_PORTS) != ALL_PORTS) {
- printk(KERN_DEBUG DRV_NAME "(%s): enabling SATA channel interrupts (0x%x)\n",
- pci_name(pdev), (int) tmp8);
+ dev_printk(KERN_DEBUG, &pdev->dev,
+ "enabling SATA channel interrupts (0x%x)\n",
+ (int) tmp8);
tmp8 |= ALL_PORTS;
pci_write_config_byte(pdev, SATA_INT_GATE, tmp8);
}
@@ -284,8 +286,9 @@
/* make sure native mode is enabled */
pci_read_config_byte(pdev, SATA_NATIVE_MODE, &tmp8);
if ((tmp8 & NATIVE_MODE_ALL) != NATIVE_MODE_ALL) {
- printk(KERN_DEBUG DRV_NAME "(%s): enabling SATA channel native mode (0x%x)\n",
- pci_name(pdev), (int) tmp8);
+ dev_printk(KERN_DEBUG, &pdev->dev,
+ "enabling SATA channel native mode (0x%x)\n",
+ (int) tmp8);
tmp8 |= NATIVE_MODE_ALL;
pci_write_config_byte(pdev, SATA_NATIVE_MODE, tmp8);
}
@@ -303,7 +306,7 @@
u8 tmp8;
if (!printed_version++)
- printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+ dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
rc = pci_enable_device(pdev);
if (rc)
@@ -318,8 +321,9 @@
if (board_id == vt6420) {
pci_read_config_byte(pdev, SATA_PATA_SHARING, &tmp8);
if (tmp8 & SATA_2DEV) {
- printk(KERN_ERR DRV_NAME "(%s): SATA master/slave not supported (0x%x)\n",
- pci_name(pdev), (int) tmp8);
+ dev_printk(KERN_ERR, &pdev->dev,
+ "SATA master/slave not supported (0x%x)\n",
+ (int) tmp8);
rc = -EIO;
goto err_out_regions;
}
@@ -332,10 +336,11 @@
for (i = 0; i < ARRAY_SIZE(svia_bar_sizes); i++)
if ((pci_resource_start(pdev, i) == 0) ||
(pci_resource_len(pdev, i) < bar_sizes[i])) {
- printk(KERN_ERR DRV_NAME "(%s): invalid PCI BAR %u (sz 0x%lx, val 0x%lx)\n",
- pci_name(pdev), i,
- pci_resource_start(pdev, i),
- pci_resource_len(pdev, i));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "invalid PCI BAR %u (sz 0x%lx, val 0x%lx)\n",
+ i,
+ pci_resource_start(pdev, i),
+ pci_resource_len(pdev, i));
rc = -ENODEV;
goto err_out_regions;
}
@@ -353,8 +358,7 @@
probe_ent = vt6421_init_probe_ent(pdev);
if (!probe_ent) {
- printk(KERN_ERR DRV_NAME "(%s): out of memory\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev, "out of memory\n");
rc = -ENOMEM;
goto err_out_regions;
}