ARM: 5831/1: ARM: U8500 core machine support
Adds core support for the ST-Ericsson U8500
platform. It supports memory mappings, binds to
the existing modules like GIC, SCU, TWD and
local timers and sets up the infrastructure for
the secondary core.
Reviewed-by: Alessandro Rubini <rubini@unipv.it>
Reviewed-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
new file mode 100644
index 0000000..aa5afbc
--- /dev/null
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -0,0 +1,158 @@
+/*
+ * Copyright (C) 2008-2009 ST-Ericsson
+ *
+ * Author: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2, as
+ * published by the Free Software Foundation.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/amba/bus.h>
+#include <linux/amba/pl022.h>
+#include <linux/spi/spi.h>
+
+#include <asm/localtimer.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <plat/mtu.h>
+
+#include <mach/hardware.h>
+#include <mach/setup.h>
+
+#define __MEM_4K_RESOURCE(x) \
+ .res = {.start = (x), .end = (x) + SZ_4K - 1, .flags = IORESOURCE_MEM}
+
+/* These are active devices on this board */
+static struct amba_device uart0_device = {
+ .dev = { .init_name = "uart0" },
+ __MEM_4K_RESOURCE(U8500_UART0_BASE),
+ .irq = {IRQ_UART0, NO_IRQ},
+};
+
+static struct amba_device uart1_device = {
+ .dev = { .init_name = "uart1" },
+ __MEM_4K_RESOURCE(U8500_UART1_BASE),
+ .irq = {IRQ_UART1, NO_IRQ},
+};
+
+static struct amba_device uart2_device = {
+ .dev = { .init_name = "uart2" },
+ __MEM_4K_RESOURCE(U8500_UART2_BASE),
+ .irq = {IRQ_UART2, NO_IRQ},
+};
+
+static void ab4500_spi_cs_control(u32 command)
+{
+ /* set the FRM signal, which is CS - TODO */
+}
+
+struct pl022_config_chip ab4500_chip_info = {
+ .lbm = LOOPBACK_DISABLED,
+ .com_mode = INTERRUPT_TRANSFER,
+ .iface = SSP_INTERFACE_MOTOROLA_SPI,
+ /* we can act as master only */
+ .hierarchy = SSP_MASTER,
+ .slave_tx_disable = 0,
+ .endian_rx = SSP_RX_MSB,
+ .endian_tx = SSP_TX_MSB,
+ .data_size = SSP_DATA_BITS_24,
+ .rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
+ .tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
+ .clk_phase = SSP_CLK_SECOND_EDGE,
+ .clk_pol = SSP_CLK_POL_IDLE_HIGH,
+ .cs_control = ab4500_spi_cs_control,
+};
+
+static struct spi_board_info u8500_spi_devices[] = {
+ {
+ .modalias = "ab4500",
+ .controller_data = &ab4500_chip_info,
+ .max_speed_hz = 12000000,
+ .bus_num = 0,
+ .chip_select = 0,
+ .mode = SPI_MODE_0,
+ .irq = IRQ_AB4500,
+ },
+};
+
+static struct pl022_ssp_controller ssp0_platform_data = {
+ .bus_id = 0,
+ /* pl022 not yet supports dma */
+ .enable_dma = 0,
+ /* on this platform, gpio 31,142,144,214 &
+ * 224 are connected as chip selects
+ */
+ .num_chipselect = 5,
+};
+
+static struct amba_device pl022_device = {
+ .dev = {
+ .coherent_dma_mask = ~0,
+ .init_name = "pl022",
+ .platform_data = &ssp0_platform_data,
+ },
+ .res = {
+ .start = U8500_SSP0_BASE,
+ .end = U8500_SSP0_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ .irq = {IRQ_SSP0, NO_IRQ },
+ /* ST-Ericsson modified id */
+ .periphid = SSP_PER_ID,
+};
+
+static struct amba_device *amba_devs[] __initdata = {
+ &uart0_device,
+ &uart1_device,
+ &uart2_device,
+ &pl022_device,
+};
+
+static void __init u8500_timer_init(void)
+{
+#ifdef CONFIG_LOCAL_TIMERS
+ /* Setup the local timer base */
+ twd_base = __io_address(U8500_TWD_BASE);
+#endif
+ /* Setup the MTU base */
+ mtu_base = __io_address(U8500_MTU0_BASE);
+
+ nmdk_timer_init();
+}
+
+static struct sys_timer u8500_timer = {
+ .init = u8500_timer_init,
+};
+
+static void __init u8500_init_machine(void)
+{
+ int i;
+
+ /* Register the active AMBA devices on this board */
+ for (i = 0; i < ARRAY_SIZE(amba_devs); i++)
+ amba_device_register(amba_devs[i], &iomem_resource);
+
+ spi_register_board_info(u8500_spi_devices,
+ ARRAY_SIZE(u8500_spi_devices));
+
+ u8500_init_devices();
+}
+
+MACHINE_START(U8500, "ST-Ericsson MOP500 platform")
+ /* Maintainer: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> */
+ .phys_io = U8500_UART2_BASE,
+ .io_pg_offst = (IO_ADDRESS(U8500_UART2_BASE) >> 18) & 0xfffc,
+ .boot_params = 0x100,
+ .map_io = u8500_map_io,
+ .init_irq = u8500_init_irq,
+ /* we re-use nomadik timer here */
+ .timer = &u8500_timer,
+ .init_machine = u8500_init_machine,
+MACHINE_END