ide: make ide_pc_intr() static

* Always use ide_pc_intr as a handler in ide_pc_intr().

* Remove no longer used ide*_pc_intr() and 'handler'
  argument from ide_{transfer_pc,pc_intr}().

* Make ide_pc_intr() static.

There should be no functional changes caused by this patch.

Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
diff --git a/drivers/ide/ide-atapi.c b/drivers/ide/ide-atapi.c
index f46bc51..b558663 100644
--- a/drivers/ide/ide-atapi.c
+++ b/drivers/ide/ide-atapi.c
@@ -246,7 +246,12 @@
 }
 EXPORT_SYMBOL_GPL(ide_scsi_expiry);
 
-ide_startstop_t ide_pc_intr(ide_drive_t *drive, ide_handler_t *handler)
+/*
+ * This is the usual interrupt handler which will be called during a packet
+ * command.  We will transfer some of the data (as requested by the drive)
+ * and will re-point interrupt handler to us.
+ */
+static ide_startstop_t ide_pc_intr(ide_drive_t *drive)
 {
 	struct ide_atapi_pc *pc = drive->pc;
 	ide_hwif_t *hwif = drive->hwif;
@@ -425,10 +430,9 @@
 		  rq->cmd[0], bcount);
 next_irq:
 	/* And set the interrupt handler again */
-	ide_set_handler(drive, handler, timeout, expiry);
+	ide_set_handler(drive, ide_pc_intr, timeout, expiry);
 	return ide_started;
 }
-EXPORT_SYMBOL_GPL(ide_pc_intr);
 
 static u8 ide_read_ireason(ide_drive_t *drive)
 {
@@ -464,8 +468,7 @@
 	return ireason;
 }
 
-ide_startstop_t ide_transfer_pc(ide_drive_t *drive,
-				ide_handler_t *handler, unsigned int timeout,
+ide_startstop_t ide_transfer_pc(ide_drive_t *drive, unsigned int timeout,
 				ide_expiry_t *expiry)
 {
 	struct ide_atapi_pc *pc = drive->pc;
@@ -491,7 +494,7 @@
 	}
 
 	/* Set the interrupt routine */
-	ide_set_handler(drive, handler, timeout, expiry);
+	ide_set_handler(drive, ide_pc_intr, timeout, expiry);
 
 	/* Begin DMA, if necessary */
 	if (pc->flags & PC_FLAG_DMA_OK) {
diff --git a/drivers/ide/ide-floppy.c b/drivers/ide/ide-floppy.c
index 378a22c..7be3cd5 100644
--- a/drivers/ide/ide-floppy.c
+++ b/drivers/ide/ide-floppy.c
@@ -193,12 +193,6 @@
 	idefloppy_end_request(drive, uptodate, 0);
 }
 
-/* The usual interrupt handler called during a packet command. */
-static ide_startstop_t idefloppy_pc_intr(ide_drive_t *drive)
-{
-	return ide_pc_intr(drive, idefloppy_pc_intr);
-}
-
 /*
  * What we have here is a classic case of a top half / bottom half interrupt
  * service routine. In interrupt mode, the device sends an interrupt to signal
@@ -230,7 +224,7 @@
 	 * where the Busy flag was apparently being deasserted before the
 	 * unit was ready to receive data. This was happening on a
 	 * 1200 MHz Athlon system. 10/26/01 25msec is too short,
-	 * 40 and 50msec work well. idefloppy_pc_intr will not be actually
+	 * 40 and 50msec work well. ide_pc_intr will not be actually
 	 * used until after the packet is moved in about 50 msec.
 	 */
 	if (drive->atapi_flags & IDE_AFLAG_ZIP_DRIVE) {
@@ -241,7 +235,7 @@
 		expiry = NULL;
 	}
 
-	return ide_transfer_pc(drive, idefloppy_pc_intr, timeout, expiry);
+	return ide_transfer_pc(drive, timeout, expiry);
 }
 
 static void ide_floppy_report_error(idefloppy_floppy_t *floppy,
diff --git a/drivers/ide/ide-tape.c b/drivers/ide/ide-tape.c
index 5c26e98..a148de6 100644
--- a/drivers/ide/ide-tape.c
+++ b/drivers/ide/ide-tape.c
@@ -619,18 +619,6 @@
 }
 
 /*
- * This is the usual interrupt handler which will be called during a packet
- * command. We will transfer some of the data (as requested by the drive) and
- * will re-point interrupt handler to us. When data transfer is finished, we
- * will act according to the algorithm described before
- * idetape_issue_pc.
- */
-static ide_startstop_t idetape_pc_intr(ide_drive_t *drive)
-{
-	return ide_pc_intr(drive, idetape_pc_intr);
-}
-
-/*
  * Packet Command Interface
  *
  * The current Packet Command is available in drive->pc, and will not change
@@ -640,9 +628,9 @@
  * The handling will be done in three stages:
  *
  * 1. idetape_issue_pc will send the packet command to the drive, and will set
- * the interrupt handler to idetape_pc_intr.
+ * the interrupt handler to ide_pc_intr.
  *
- * 2. On each interrupt, idetape_pc_intr will be called. This step will be
+ * 2. On each interrupt, ide_pc_intr will be called. This step will be
  * repeated until the device signals us that no more interrupts will be issued.
  *
  * 3. ATAPI Tape media access commands have immediate status with a delayed
@@ -668,7 +656,7 @@
  */
 static ide_startstop_t idetape_transfer_pc(ide_drive_t *drive)
 {
-	return ide_transfer_pc(drive, idetape_pc_intr, WAIT_TAPE_CMD, NULL);
+	return ide_transfer_pc(drive, WAIT_TAPE_CMD, NULL);
 }
 
 static ide_startstop_t idetape_issue_pc(ide_drive_t *drive,