ARM: OMAP: Apollon MMC support
Apollon board MMC supports on OMAP2
TODO:
We have to check MMC on H4
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c
index 7993b7b..2db6b73 100644
--- a/arch/arm/mach-omap2/board-apollon.c
+++ b/arch/arm/mach-omap2/board-apollon.c
@@ -166,8 +166,8 @@
static struct omap_mmc_config apollon_mmc_config __initdata = {
.mmc [0] = {
- .enabled = 0,
- .wire4 = 0,
+ .enabled = 1,
+ .wire4 = 1,
.wp_pin = -1,
.power_pin = -1,
.switch_pin = -1,
@@ -257,6 +257,9 @@
/* REVISIT: where's the correct place */
omap_cfg_reg(W19_24XX_SYS_NIRQ);
+ /* Use Interal loop-back in MMC/SDIO Module Input Clock selection */
+ CONTROL_DEVCONF |= (1 << 24);
+
/*
* Make sure the serial ports are muxed on at this point.
* You have to mux them off in device drivers later on
diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c
index 60ef084..f538d0f 100644
--- a/arch/arm/mach-omap2/mux.c
+++ b/arch/arm/mach-omap2/mux.c
@@ -104,6 +104,20 @@
MUX_CFG_24XX("K15_24XX_UART3_TX", 0x118, 0, 0, 0, 1)
MUX_CFG_24XX("K14_24XX_UART3_RX", 0x119, 0, 0, 0, 1)
+/* MMC/SDIO */
+MUX_CFG_24XX("G19_24XX_MMC_CLKO", 0x0f3, 0, 0, 0, 1)
+MUX_CFG_24XX("H18_24XX_MMC_CMD", 0x0f4, 0, 0, 0, 1)
+MUX_CFG_24XX("F20_24XX_MMC_DAT0", 0x0f5, 0, 0, 0, 1)
+MUX_CFG_24XX("H14_24XX_MMC_DAT1", 0x0f6, 0, 0, 0, 1)
+MUX_CFG_24XX("E19_24XX_MMC_DAT2", 0x0f7, 0, 0, 0, 1)
+MUX_CFG_24XX("D19_24XX_MMC_DAT3", 0x0f8, 0, 0, 0, 1)
+MUX_CFG_24XX("F19_24XX_MMC_DAT_DIR0", 0x0f9, 0, 0, 0, 1)
+MUX_CFG_24XX("E20_24XX_MMC_DAT_DIR1", 0x0fa, 0, 0, 0, 1)
+MUX_CFG_24XX("F18_24XX_MMC_DAT_DIR2", 0x0fb, 0, 0, 0, 1)
+MUX_CFG_24XX("E18_24XX_MMC_DAT_DIR3", 0x0fc, 0, 0, 0, 1)
+MUX_CFG_24XX("G18_24XX_MMC_CMD_DIR", 0x0fd, 0, 0, 0, 1)
+MUX_CFG_24XX("H15_24XX_MMC_CLKI", 0x0fe, 0, 0, 0, 1)
+
/* Keypad GPIO*/
MUX_CFG_24XX("T19_24XX_KBR0", 0x106, 3, 1, 1, 1)
MUX_CFG_24XX("R19_24XX_KBR1", 0x107, 3, 1, 1, 1)
diff --git a/arch/arm/plat-omap/devices.c b/arch/arm/plat-omap/devices.c
index 1812f23..dbc3f44 100644
--- a/arch/arm/plat-omap/devices.c
+++ b/arch/arm/plat-omap/devices.c
@@ -148,7 +148,7 @@
#ifdef CONFIG_ARCH_OMAP24XX
#define OMAP_MMC1_BASE 0x4809c000
-#define OMAP_MMC1_INT 83
+#define OMAP_MMC1_INT INT_24XX_MMC_IRQ
#else
#define OMAP_MMC1_BASE 0xfffb7800
#define OMAP_MMC1_INT INT_MMC
@@ -225,7 +225,14 @@
/* block 1 is always available and has just one pinout option */
mmc = &mmc_conf->mmc[0];
if (mmc->enabled) {
- if (!cpu_is_omap24xx()) {
+ if (cpu_is_omap24xx()) {
+ omap_cfg_reg(H18_24XX_MMC_CMD);
+ omap_cfg_reg(H15_24XX_MMC_CLKI);
+ omap_cfg_reg(G19_24XX_MMC_CLKO);
+ omap_cfg_reg(F20_24XX_MMC_DAT0);
+ omap_cfg_reg(F19_24XX_MMC_DAT_DIR0);
+ omap_cfg_reg(G18_24XX_MMC_CMD_DIR);
+ } else {
omap_cfg_reg(MMC_CMD);
omap_cfg_reg(MMC_CLK);
omap_cfg_reg(MMC_DAT0);
@@ -236,7 +243,14 @@
}
}
if (mmc->wire4) {
- if (!cpu_is_omap24xx()) {
+ if (cpu_is_omap24xx()) {
+ omap_cfg_reg(H14_24XX_MMC_DAT1);
+ omap_cfg_reg(E19_24XX_MMC_DAT2);
+ omap_cfg_reg(D19_24XX_MMC_DAT3);
+ omap_cfg_reg(E20_24XX_MMC_DAT_DIR1);
+ omap_cfg_reg(F18_24XX_MMC_DAT_DIR2);
+ omap_cfg_reg(E18_24XX_MMC_DAT_DIR3);
+ } else {
omap_cfg_reg(MMC_DAT1);
/* NOTE: DAT2 can be on W10 (here) or M15 */
if (!mmc->nomux)
diff --git a/include/asm-arm/arch-omap/irqs.h b/include/asm-arm/arch-omap/irqs.h
index 636f21c..c5bb05a 100644
--- a/include/asm-arm/arch-omap/irqs.h
+++ b/include/asm-arm/arch-omap/irqs.h
@@ -262,6 +262,7 @@
#define INT_24XX_UART1_IRQ 72
#define INT_24XX_UART2_IRQ 73
#define INT_24XX_UART3_IRQ 74
+#define INT_24XX_MMC_IRQ 83
/* Max. 128 level 2 IRQs (OMAP1610), 192 GPIOs (OMAP730) and
* 16 MPUIO lines */
diff --git a/include/asm-arm/arch-omap/mux.h b/include/asm-arm/arch-omap/mux.h
index 679869c..a6df97c 100644
--- a/include/asm-arm/arch-omap/mux.h
+++ b/include/asm-arm/arch-omap/mux.h
@@ -461,6 +461,20 @@
K15_24XX_UART3_TX,
K14_24XX_UART3_RX,
+ /* MMC/SDIO */
+ G19_24XX_MMC_CLKO,
+ H18_24XX_MMC_CMD,
+ F20_24XX_MMC_DAT0,
+ H14_24XX_MMC_DAT1,
+ E19_24XX_MMC_DAT2,
+ D19_24XX_MMC_DAT3,
+ F19_24XX_MMC_DAT_DIR0,
+ E20_24XX_MMC_DAT_DIR1,
+ F18_24XX_MMC_DAT_DIR2,
+ E18_24XX_MMC_DAT_DIR3,
+ G18_24XX_MMC_CMD_DIR,
+ H15_24XX_MMC_CLKI,
+
/* Keypad GPIO*/
T19_24XX_KBR0,
R19_24XX_KBR1,