regulator: palmas: Return raw register values as the selectors in [get|set]_voltage_sel
Don't adjust the selector in [get|set]_voltage_sel, fix it in list_voltage() instead.
For smps*(except smps10), the vsel reg-value and voltage mapping as below:
reg-value volt (uV) ( Assume RANGE is x1 )
0 0
1 500000
2 500000
3 500000
4 500000
5 500000
6 500000 (0.49V + 1 * 0.01V) * RANGE
7 510000 (0.49V + 2 * 0.01V) * RANGE
8 520000 (0.49V + 3 * 0.01V) * RANGE
9 530000 (0.49V + 4 * 0.01V) * RANGE
....
The linear mapping is start from selector 6.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
diff --git a/drivers/regulator/palmas-regulator.c b/drivers/regulator/palmas-regulator.c
index 07aee69..151c0c4 100644
--- a/drivers/regulator/palmas-regulator.c
+++ b/drivers/regulator/palmas-regulator.c
@@ -309,19 +309,22 @@
int id = rdev_get_id(dev);
int mult = 1;
- if (!selector)
- return 0;
-
/* Read the multiplier set in VSEL register to return
* the correct voltage.
*/
if (pmic->range[id])
mult = 2;
- /* Voltage is (0.49V + (selector * 0.01V)) * RANGE
- * as defined in data sheet. RANGE is either x1 or x2
- */
- return (490000 + (selector * 10000)) * mult;
+ if (selector == 0)
+ return 0;
+ else if (selector < 6)
+ return 500000 * mult;
+ else
+ /* Voltage is linear mapping starting from selector 6,
+ * volt = (0.49V + ((selector - 5) * 0.01V)) * RANGE
+ * RANGE is either x1 or x2
+ */
+ return (490000 + ((selector - 5) * 10000)) * mult;
}
static int palmas_get_voltage_smps_sel(struct regulator_dev *dev)
@@ -338,15 +341,6 @@
selector = reg & PALMAS_SMPS12_VOLTAGE_VSEL_MASK;
- /* Adjust selector to match list_voltage ranges */
- if ((selector > 0) && (selector < 6))
- selector = 6;
- if (!selector)
- selector = 5;
- if (selector > 121)
- selector = 121;
- selector -= 5;
-
return selector;
}
@@ -355,19 +349,15 @@
{
struct palmas_pmic *pmic = rdev_get_drvdata(dev);
int id = rdev_get_id(dev);
- unsigned int reg = 0;
- unsigned int addr;
+ unsigned int reg, addr;
addr = palmas_regs_info[id].vsel_addr;
+ reg = selector;
/* Make sure we don't change the value of RANGE */
if (pmic->range[id])
reg |= PALMAS_SMPS12_VOLTAGE_RANGE;
- /* Adjust the linux selector into range used in VSEL register */
- if (selector)
- reg |= selector + 5;
-
palmas_smps_write(pmic->palmas, addr, reg);
return 0;
@@ -386,11 +376,11 @@
if (pmic->range[id]) { /* RANGE is x2 */
if (min_uV < 1000000)
min_uV = 1000000;
- ret = DIV_ROUND_UP(min_uV - 1000000, 20000) + 1;
+ ret = DIV_ROUND_UP(min_uV - 1000000, 20000) + 6;
} else { /* RANGE is x1 */
if (min_uV < 500000)
min_uV = 500000;
- ret = DIV_ROUND_UP(min_uV - 500000, 10000) + 1;
+ ret = DIV_ROUND_UP(min_uV - 500000, 10000) + 6;
}
/* Map back into a voltage to verify we're still in bounds */