Merge branch 'sirf/dt' into next/dt
From Barry Song:
Some missed dt nodes for sirf dts for 3.13. Among them:
- add missed chhifbg node in prima2 and atlas6 dts
- add missed cell, cs and dma channel for SPI nodes
- add missed graphics2d iobg in atlas6 dts
- add missed address-cells and size-cells for prima2 I2C
- add missed memcontrol-monitor node in prima2 and atlas6 dts
* sirf/dt:
ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
Signed-off-by: Olof Johansson <olof@lixom.net>
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index 91b7049..808c154 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -21,7 +21,8 @@
Optional properties:
- ti,no_idle_on_suspend: When present, it prevents the PM to idle the module
during suspend.
-
+- ti,no-reset-on-init: When present, the module should not be reset at init
+- ti,no-idle-on-init: When present, the module should not be idled at init
Example:
diff --git a/Documentation/devicetree/bindings/arm/vic.txt b/Documentation/devicetree/bindings/arm/vic.txt
index 266716b..dd52721 100644
--- a/Documentation/devicetree/bindings/arm/vic.txt
+++ b/Documentation/devicetree/bindings/arm/vic.txt
@@ -18,6 +18,15 @@
Optional properties:
- interrupts : Interrupt source for parent controllers if the VIC is nested.
+- valid-mask : A one cell big bit mask of valid interrupt sources. Each bit
+ represents single interrupt source, starting from source 0 at LSb and ending
+ at source 31 at MSb. A bit that is set means that the source is wired and
+ clear means otherwise. If unspecified, defaults to all valid.
+- valid-wakeup-mask : A one cell big bit mask of interrupt sources that can be
+ configured as wake up source for the system. Order of bits is the same as for
+ valid-mask property. A set bit means that this interrupt source can be
+ configured as a wake up source for the system. If unspecied, defaults to all
+ interrupt sources configurable as wake up sources.
Example:
@@ -26,4 +35,7 @@
interrupt-controller;
#interrupt-cells = <1>;
reg = <0x60000 0x1000>;
+
+ valid-mask = <0xffffff7f>;
+ valid-wakeup-mask = <0x0000ff7f>;
};
diff --git a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
new file mode 100644
index 0000000..c62391f
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
@@ -0,0 +1,19 @@
+* Core Divider Clock bindings for Marvell MVEBU SoCs
+
+The following is a list of provided IDs and clock names on Armada 370/XP:
+ 0 = nand (NAND clock)
+
+Required properties:
+- compatible : must be "marvell,armada-370-corediv-clock"
+- reg : must be the register address of Core Divider control register
+- #clock-cells : from common clock binding; shall be set to 1
+- clocks : must be set to the parent's phandle
+
+Example:
+
+corediv_clk: corediv-clocks@18740 {
+ compatible = "marvell,armada-370-corediv-clock";
+ reg = <0x18740 0xc>;
+ #clock-cells = <1>;
+ clocks = <&pll>;
+};
diff --git a/Documentation/devicetree/bindings/crypto/omap-aes.txt b/Documentation/devicetree/bindings/crypto/omap-aes.txt
new file mode 100644
index 0000000..fd97176
--- /dev/null
+++ b/Documentation/devicetree/bindings/crypto/omap-aes.txt
@@ -0,0 +1,31 @@
+OMAP SoC AES crypto Module
+
+Required properties:
+
+- compatible : Should contain entries for this and backward compatible
+ AES versions:
+ - "ti,omap2-aes" for OMAP2.
+ - "ti,omap3-aes" for OMAP3.
+ - "ti,omap4-aes" for OMAP4 and AM33XX.
+ Note that the OMAP2 and 3 versions are compatible (OMAP3 supports
+ more algorithms) but they are incompatible with OMAP4.
+- ti,hwmods: Name of the hwmod associated with the AES module
+- reg : Offset and length of the register set for the module
+- interrupts : the interrupt-specifier for the AES module.
+
+Optional properties:
+- dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
+ Documentation/devicetree/bindings/dma/dma.txt
+- dma-names: DMA request names should include "tx" and "rx" if present.
+
+Example:
+ /* AM335x */
+ aes: aes@53500000 {
+ compatible = "ti,omap4-aes";
+ ti,hwmods = "aes";
+ reg = <0x53500000 0xa0>;
+ interrupts = <102>;
+ dmas = <&edma 6>,
+ <&edma 5>;
+ dma-names = "tx", "rx";
+ };
diff --git a/Documentation/devicetree/bindings/crypto/omap-sham.txt b/Documentation/devicetree/bindings/crypto/omap-sham.txt
new file mode 100644
index 0000000..f839acd
--- /dev/null
+++ b/Documentation/devicetree/bindings/crypto/omap-sham.txt
@@ -0,0 +1,28 @@
+OMAP SoC SHA crypto Module
+
+Required properties:
+
+- compatible : Should contain entries for this and backward compatible
+ SHAM versions:
+ - "ti,omap2-sham" for OMAP2 & OMAP3.
+ - "ti,omap4-sham" for OMAP4 and AM33XX.
+ Note that these two versions are incompatible.
+- ti,hwmods: Name of the hwmod associated with the SHAM module
+- reg : Offset and length of the register set for the module
+- interrupts : the interrupt-specifier for the SHAM module.
+
+Optional properties:
+- dmas: DMA specifiers for the rx dma. See the DMA client binding,
+ Documentation/devicetree/bindings/dma/dma.txt
+- dma-names: DMA request name. Should be "rx" if a dma is present.
+
+Example:
+ /* AM335x */
+ sham: sham@53100000 {
+ compatible = "ti,omap4-sham";
+ ti,hwmods = "sham";
+ reg = <0x53100000 0x200>;
+ interrupts = <109>;
+ dmas = <&edma 36>;
+ dma-names = "rx";
+ };
diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
index ed271fc..8c8908a 100644
--- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
+++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
@@ -20,8 +20,17 @@
ti,non-removable: non-removable slot (like eMMC)
ti,needs-special-reset: Requires a special softreset sequence
ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed
+dmas: List of DMA specifiers with the controller specific format
+as described in the generic DMA client binding. A tx and rx
+specifier is required.
+dma-names: List of DMA request names. These strings correspond
+1:1 with the DMA specifiers listed in dmas. The string naming is
+to be "rx" and "tx" for RX and TX DMA requests, respectively.
-Example:
+Examples:
+
+[hwmod populated DMA resources]
+
mmc1: mmc@0x4809c000 {
compatible = "ti,omap4-hsmmc";
reg = <0x4809c000 0x400>;
@@ -31,3 +40,18 @@
vmmc-supply = <&vmmc>; /* phandle to regulator node */
ti,non-removable;
};
+
+[generic DMA request binding]
+
+ mmc1: mmc@0x4809c000 {
+ compatible = "ti,omap4-hsmmc";
+ reg = <0x4809c000 0x400>;
+ ti,hwmods = "mmc1";
+ ti,dual-volt;
+ bus-width = <4>;
+ vmmc-supply = <&vmmc>; /* phandle to regulator node */
+ ti,non-removable;
+ dmas = <&edma 24
+ &edma 25>;
+ dma-names = "tx", "rx";
+ };
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt
index 3077370..1e70a8a 100644
--- a/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt
@@ -59,16 +59,16 @@
Optional subnode-properties:
- fsl,drive-strength: Integer.
- 0: 4 mA
- 1: 8 mA
- 2: 12 mA
- 3: 16 mA
+ 0: MXS_DRIVE_4mA
+ 1: MXS_DRIVE_8mA
+ 2: MXS_DRIVE_12mA
+ 3: MXS_DRIVE_16mA
- fsl,voltage: Integer.
- 0: 1.8 V
- 1: 3.3 V
+ 0: MXS_VOLTAGE_LOW - 1.8 V
+ 1: MXS_VOLTAGE_HIGH - 3.3 V
- fsl,pull-up: Integer.
- 0: Disable the internal pull-up
- 1: Enable the internal pull-up
+ 0: MXS_PULL_DISABLE - Disable the internal pull-up
+ 1: MXS_PULL_ENABLE - Enable the internal pull-up
Note that when enabling the pull-up, the internal pad keeper gets disabled.
Also, some pins doesn't have a pull up, in that case, setting the fsl,pull-up
@@ -85,23 +85,32 @@
mmc0_8bit_pins_a: mmc0-8bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2000 0x2010 0x2020 0x2030
- 0x2040 0x2050 0x2060 0x2070
- 0x2080 0x2090 0x20a0>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ MX28_PAD_SSP0_DATA0__SSP0_D0
+ MX28_PAD_SSP0_DATA1__SSP0_D1
+ MX28_PAD_SSP0_DATA2__SSP0_D2
+ MX28_PAD_SSP0_DATA3__SSP0_D3
+ MX28_PAD_SSP0_DATA4__SSP0_D4
+ MX28_PAD_SSP0_DATA5__SSP0_D5
+ MX28_PAD_SSP0_DATA6__SSP0_D6
+ MX28_PAD_SSP0_DATA7__SSP0_D7
+ MX28_PAD_SSP0_CMD__SSP0_CMD
+ MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT
+ MX28_PAD_SSP0_SCK__SSP0_SCK
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
mmc_cd_cfg: mmc-cd-cfg {
- fsl,pinmux-ids = <0x2090>;
- fsl,pull-up = <0>;
+ fsl,pinmux-ids = <MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
mmc_sck_cfg: mmc-sck-cfg {
- fsl,pinmux-ids = <0x20a0>;
- fsl,drive-strength = <2>;
- fsl,pull-up = <0>;
+ fsl,pinmux-ids = <MX28_PAD_SSP0_SCK__SSP0_SCK>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
@@ -112,811 +121,7 @@
node mmc0-8bit defines. Only the configuration properties to be adjusted need
to be listed in the config nodes.
-Valid values for i.MX28 pinmux-id:
-
-pinmux id
------- --
-MX28_PAD_GPMI_D00__GPMI_D0 0x0000
-MX28_PAD_GPMI_D01__GPMI_D1 0x0010
-MX28_PAD_GPMI_D02__GPMI_D2 0x0020
-MX28_PAD_GPMI_D03__GPMI_D3 0x0030
-MX28_PAD_GPMI_D04__GPMI_D4 0x0040
-MX28_PAD_GPMI_D05__GPMI_D5 0x0050
-MX28_PAD_GPMI_D06__GPMI_D6 0x0060
-MX28_PAD_GPMI_D07__GPMI_D7 0x0070
-MX28_PAD_GPMI_CE0N__GPMI_CE0N 0x0100
-MX28_PAD_GPMI_CE1N__GPMI_CE1N 0x0110
-MX28_PAD_GPMI_CE2N__GPMI_CE2N 0x0120
-MX28_PAD_GPMI_CE3N__GPMI_CE3N 0x0130
-MX28_PAD_GPMI_RDY0__GPMI_READY0 0x0140
-MX28_PAD_GPMI_RDY1__GPMI_READY1 0x0150
-MX28_PAD_GPMI_RDY2__GPMI_READY2 0x0160
-MX28_PAD_GPMI_RDY3__GPMI_READY3 0x0170
-MX28_PAD_GPMI_RDN__GPMI_RDN 0x0180
-MX28_PAD_GPMI_WRN__GPMI_WRN 0x0190
-MX28_PAD_GPMI_ALE__GPMI_ALE 0x01a0
-MX28_PAD_GPMI_CLE__GPMI_CLE 0x01b0
-MX28_PAD_GPMI_RESETN__GPMI_RESETN 0x01c0
-MX28_PAD_LCD_D00__LCD_D0 0x1000
-MX28_PAD_LCD_D01__LCD_D1 0x1010
-MX28_PAD_LCD_D02__LCD_D2 0x1020
-MX28_PAD_LCD_D03__LCD_D3 0x1030
-MX28_PAD_LCD_D04__LCD_D4 0x1040
-MX28_PAD_LCD_D05__LCD_D5 0x1050
-MX28_PAD_LCD_D06__LCD_D6 0x1060
-MX28_PAD_LCD_D07__LCD_D7 0x1070
-MX28_PAD_LCD_D08__LCD_D8 0x1080
-MX28_PAD_LCD_D09__LCD_D9 0x1090
-MX28_PAD_LCD_D10__LCD_D10 0x10a0
-MX28_PAD_LCD_D11__LCD_D11 0x10b0
-MX28_PAD_LCD_D12__LCD_D12 0x10c0
-MX28_PAD_LCD_D13__LCD_D13 0x10d0
-MX28_PAD_LCD_D14__LCD_D14 0x10e0
-MX28_PAD_LCD_D15__LCD_D15 0x10f0
-MX28_PAD_LCD_D16__LCD_D16 0x1100
-MX28_PAD_LCD_D17__LCD_D17 0x1110
-MX28_PAD_LCD_D18__LCD_D18 0x1120
-MX28_PAD_LCD_D19__LCD_D19 0x1130
-MX28_PAD_LCD_D20__LCD_D20 0x1140
-MX28_PAD_LCD_D21__LCD_D21 0x1150
-MX28_PAD_LCD_D22__LCD_D22 0x1160
-MX28_PAD_LCD_D23__LCD_D23 0x1170
-MX28_PAD_LCD_RD_E__LCD_RD_E 0x1180
-MX28_PAD_LCD_WR_RWN__LCD_WR_RWN 0x1190
-MX28_PAD_LCD_RS__LCD_RS 0x11a0
-MX28_PAD_LCD_CS__LCD_CS 0x11b0
-MX28_PAD_LCD_VSYNC__LCD_VSYNC 0x11c0
-MX28_PAD_LCD_HSYNC__LCD_HSYNC 0x11d0
-MX28_PAD_LCD_DOTCLK__LCD_DOTCLK 0x11e0
-MX28_PAD_LCD_ENABLE__LCD_ENABLE 0x11f0
-MX28_PAD_SSP0_DATA0__SSP0_D0 0x2000
-MX28_PAD_SSP0_DATA1__SSP0_D1 0x2010
-MX28_PAD_SSP0_DATA2__SSP0_D2 0x2020
-MX28_PAD_SSP0_DATA3__SSP0_D3 0x2030
-MX28_PAD_SSP0_DATA4__SSP0_D4 0x2040
-MX28_PAD_SSP0_DATA5__SSP0_D5 0x2050
-MX28_PAD_SSP0_DATA6__SSP0_D6 0x2060
-MX28_PAD_SSP0_DATA7__SSP0_D7 0x2070
-MX28_PAD_SSP0_CMD__SSP0_CMD 0x2080
-MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT 0x2090
-MX28_PAD_SSP0_SCK__SSP0_SCK 0x20a0
-MX28_PAD_SSP1_SCK__SSP1_SCK 0x20c0
-MX28_PAD_SSP1_CMD__SSP1_CMD 0x20d0
-MX28_PAD_SSP1_DATA0__SSP1_D0 0x20e0
-MX28_PAD_SSP1_DATA3__SSP1_D3 0x20f0
-MX28_PAD_SSP2_SCK__SSP2_SCK 0x2100
-MX28_PAD_SSP2_MOSI__SSP2_CMD 0x2110
-MX28_PAD_SSP2_MISO__SSP2_D0 0x2120
-MX28_PAD_SSP2_SS0__SSP2_D3 0x2130
-MX28_PAD_SSP2_SS1__SSP2_D4 0x2140
-MX28_PAD_SSP2_SS2__SSP2_D5 0x2150
-MX28_PAD_SSP3_SCK__SSP3_SCK 0x2180
-MX28_PAD_SSP3_MOSI__SSP3_CMD 0x2190
-MX28_PAD_SSP3_MISO__SSP3_D0 0x21a0
-MX28_PAD_SSP3_SS0__SSP3_D3 0x21b0
-MX28_PAD_AUART0_RX__AUART0_RX 0x3000
-MX28_PAD_AUART0_TX__AUART0_TX 0x3010
-MX28_PAD_AUART0_CTS__AUART0_CTS 0x3020
-MX28_PAD_AUART0_RTS__AUART0_RTS 0x3030
-MX28_PAD_AUART1_RX__AUART1_RX 0x3040
-MX28_PAD_AUART1_TX__AUART1_TX 0x3050
-MX28_PAD_AUART1_CTS__AUART1_CTS 0x3060
-MX28_PAD_AUART1_RTS__AUART1_RTS 0x3070
-MX28_PAD_AUART2_RX__AUART2_RX 0x3080
-MX28_PAD_AUART2_TX__AUART2_TX 0x3090
-MX28_PAD_AUART2_CTS__AUART2_CTS 0x30a0
-MX28_PAD_AUART2_RTS__AUART2_RTS 0x30b0
-MX28_PAD_AUART3_RX__AUART3_RX 0x30c0
-MX28_PAD_AUART3_TX__AUART3_TX 0x30d0
-MX28_PAD_AUART3_CTS__AUART3_CTS 0x30e0
-MX28_PAD_AUART3_RTS__AUART3_RTS 0x30f0
-MX28_PAD_PWM0__PWM_0 0x3100
-MX28_PAD_PWM1__PWM_1 0x3110
-MX28_PAD_PWM2__PWM_2 0x3120
-MX28_PAD_SAIF0_MCLK__SAIF0_MCLK 0x3140
-MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK 0x3150
-MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK 0x3160
-MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 0x3170
-MX28_PAD_I2C0_SCL__I2C0_SCL 0x3180
-MX28_PAD_I2C0_SDA__I2C0_SDA 0x3190
-MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 0x31a0
-MX28_PAD_SPDIF__SPDIF_TX 0x31b0
-MX28_PAD_PWM3__PWM_3 0x31c0
-MX28_PAD_PWM4__PWM_4 0x31d0
-MX28_PAD_LCD_RESET__LCD_RESET 0x31e0
-MX28_PAD_ENET0_MDC__ENET0_MDC 0x4000
-MX28_PAD_ENET0_MDIO__ENET0_MDIO 0x4010
-MX28_PAD_ENET0_RX_EN__ENET0_RX_EN 0x4020
-MX28_PAD_ENET0_RXD0__ENET0_RXD0 0x4030
-MX28_PAD_ENET0_RXD1__ENET0_RXD1 0x4040
-MX28_PAD_ENET0_TX_CLK__ENET0_TX_CLK 0x4050
-MX28_PAD_ENET0_TX_EN__ENET0_TX_EN 0x4060
-MX28_PAD_ENET0_TXD0__ENET0_TXD0 0x4070
-MX28_PAD_ENET0_TXD1__ENET0_TXD1 0x4080
-MX28_PAD_ENET0_RXD2__ENET0_RXD2 0x4090
-MX28_PAD_ENET0_RXD3__ENET0_RXD3 0x40a0
-MX28_PAD_ENET0_TXD2__ENET0_TXD2 0x40b0
-MX28_PAD_ENET0_TXD3__ENET0_TXD3 0x40c0
-MX28_PAD_ENET0_RX_CLK__ENET0_RX_CLK 0x40d0
-MX28_PAD_ENET0_COL__ENET0_COL 0x40e0
-MX28_PAD_ENET0_CRS__ENET0_CRS 0x40f0
-MX28_PAD_ENET_CLK__CLKCTRL_ENET 0x4100
-MX28_PAD_JTAG_RTCK__JTAG_RTCK 0x4140
-MX28_PAD_EMI_D00__EMI_DATA0 0x5000
-MX28_PAD_EMI_D01__EMI_DATA1 0x5010
-MX28_PAD_EMI_D02__EMI_DATA2 0x5020
-MX28_PAD_EMI_D03__EMI_DATA3 0x5030
-MX28_PAD_EMI_D04__EMI_DATA4 0x5040
-MX28_PAD_EMI_D05__EMI_DATA5 0x5050
-MX28_PAD_EMI_D06__EMI_DATA6 0x5060
-MX28_PAD_EMI_D07__EMI_DATA7 0x5070
-MX28_PAD_EMI_D08__EMI_DATA8 0x5080
-MX28_PAD_EMI_D09__EMI_DATA9 0x5090
-MX28_PAD_EMI_D10__EMI_DATA10 0x50a0
-MX28_PAD_EMI_D11__EMI_DATA11 0x50b0
-MX28_PAD_EMI_D12__EMI_DATA12 0x50c0
-MX28_PAD_EMI_D13__EMI_DATA13 0x50d0
-MX28_PAD_EMI_D14__EMI_DATA14 0x50e0
-MX28_PAD_EMI_D15__EMI_DATA15 0x50f0
-MX28_PAD_EMI_ODT0__EMI_ODT0 0x5100
-MX28_PAD_EMI_DQM0__EMI_DQM0 0x5110
-MX28_PAD_EMI_ODT1__EMI_ODT1 0x5120
-MX28_PAD_EMI_DQM1__EMI_DQM1 0x5130
-MX28_PAD_EMI_DDR_OPEN_FB__EMI_DDR_OPEN_FEEDBACK 0x5140
-MX28_PAD_EMI_CLK__EMI_CLK 0x5150
-MX28_PAD_EMI_DQS0__EMI_DQS0 0x5160
-MX28_PAD_EMI_DQS1__EMI_DQS1 0x5170
-MX28_PAD_EMI_DDR_OPEN__EMI_DDR_OPEN 0x51a0
-MX28_PAD_EMI_A00__EMI_ADDR0 0x6000
-MX28_PAD_EMI_A01__EMI_ADDR1 0x6010
-MX28_PAD_EMI_A02__EMI_ADDR2 0x6020
-MX28_PAD_EMI_A03__EMI_ADDR3 0x6030
-MX28_PAD_EMI_A04__EMI_ADDR4 0x6040
-MX28_PAD_EMI_A05__EMI_ADDR5 0x6050
-MX28_PAD_EMI_A06__EMI_ADDR6 0x6060
-MX28_PAD_EMI_A07__EMI_ADDR7 0x6070
-MX28_PAD_EMI_A08__EMI_ADDR8 0x6080
-MX28_PAD_EMI_A09__EMI_ADDR9 0x6090
-MX28_PAD_EMI_A10__EMI_ADDR10 0x60a0
-MX28_PAD_EMI_A11__EMI_ADDR11 0x60b0
-MX28_PAD_EMI_A12__EMI_ADDR12 0x60c0
-MX28_PAD_EMI_A13__EMI_ADDR13 0x60d0
-MX28_PAD_EMI_A14__EMI_ADDR14 0x60e0
-MX28_PAD_EMI_BA0__EMI_BA0 0x6100
-MX28_PAD_EMI_BA1__EMI_BA1 0x6110
-MX28_PAD_EMI_BA2__EMI_BA2 0x6120
-MX28_PAD_EMI_CASN__EMI_CASN 0x6130
-MX28_PAD_EMI_RASN__EMI_RASN 0x6140
-MX28_PAD_EMI_WEN__EMI_WEN 0x6150
-MX28_PAD_EMI_CE0N__EMI_CE0N 0x6160
-MX28_PAD_EMI_CE1N__EMI_CE1N 0x6170
-MX28_PAD_EMI_CKE__EMI_CKE 0x6180
-MX28_PAD_GPMI_D00__SSP1_D0 0x0001
-MX28_PAD_GPMI_D01__SSP1_D1 0x0011
-MX28_PAD_GPMI_D02__SSP1_D2 0x0021
-MX28_PAD_GPMI_D03__SSP1_D3 0x0031
-MX28_PAD_GPMI_D04__SSP1_D4 0x0041
-MX28_PAD_GPMI_D05__SSP1_D5 0x0051
-MX28_PAD_GPMI_D06__SSP1_D6 0x0061
-MX28_PAD_GPMI_D07__SSP1_D7 0x0071
-MX28_PAD_GPMI_CE0N__SSP3_D0 0x0101
-MX28_PAD_GPMI_CE1N__SSP3_D3 0x0111
-MX28_PAD_GPMI_CE2N__CAN1_TX 0x0121
-MX28_PAD_GPMI_CE3N__CAN1_RX 0x0131
-MX28_PAD_GPMI_RDY0__SSP1_CARD_DETECT 0x0141
-MX28_PAD_GPMI_RDY1__SSP1_CMD 0x0151
-MX28_PAD_GPMI_RDY2__CAN0_TX 0x0161
-MX28_PAD_GPMI_RDY3__CAN0_RX 0x0171
-MX28_PAD_GPMI_RDN__SSP3_SCK 0x0181
-MX28_PAD_GPMI_WRN__SSP1_SCK 0x0191
-MX28_PAD_GPMI_ALE__SSP3_D1 0x01a1
-MX28_PAD_GPMI_CLE__SSP3_D2 0x01b1
-MX28_PAD_GPMI_RESETN__SSP3_CMD 0x01c1
-MX28_PAD_LCD_D03__ETM_DA8 0x1031
-MX28_PAD_LCD_D04__ETM_DA9 0x1041
-MX28_PAD_LCD_D08__ETM_DA3 0x1081
-MX28_PAD_LCD_D09__ETM_DA4 0x1091
-MX28_PAD_LCD_D20__ENET1_1588_EVENT2_OUT 0x1141
-MX28_PAD_LCD_D21__ENET1_1588_EVENT2_IN 0x1151
-MX28_PAD_LCD_D22__ENET1_1588_EVENT3_OUT 0x1161
-MX28_PAD_LCD_D23__ENET1_1588_EVENT3_IN 0x1171
-MX28_PAD_LCD_RD_E__LCD_VSYNC 0x1181
-MX28_PAD_LCD_WR_RWN__LCD_HSYNC 0x1191
-MX28_PAD_LCD_RS__LCD_DOTCLK 0x11a1
-MX28_PAD_LCD_CS__LCD_ENABLE 0x11b1
-MX28_PAD_LCD_VSYNC__SAIF1_SDATA0 0x11c1
-MX28_PAD_LCD_HSYNC__SAIF1_SDATA1 0x11d1
-MX28_PAD_LCD_DOTCLK__SAIF1_MCLK 0x11e1
-MX28_PAD_SSP0_DATA4__SSP2_D0 0x2041
-MX28_PAD_SSP0_DATA5__SSP2_D3 0x2051
-MX28_PAD_SSP0_DATA6__SSP2_CMD 0x2061
-MX28_PAD_SSP0_DATA7__SSP2_SCK 0x2071
-MX28_PAD_SSP1_SCK__SSP2_D1 0x20c1
-MX28_PAD_SSP1_CMD__SSP2_D2 0x20d1
-MX28_PAD_SSP1_DATA0__SSP2_D6 0x20e1
-MX28_PAD_SSP1_DATA3__SSP2_D7 0x20f1
-MX28_PAD_SSP2_SCK__AUART2_RX 0x2101
-MX28_PAD_SSP2_MOSI__AUART2_TX 0x2111
-MX28_PAD_SSP2_MISO__AUART3_RX 0x2121
-MX28_PAD_SSP2_SS0__AUART3_TX 0x2131
-MX28_PAD_SSP2_SS1__SSP2_D1 0x2141
-MX28_PAD_SSP2_SS2__SSP2_D2 0x2151
-MX28_PAD_SSP3_SCK__AUART4_TX 0x2181
-MX28_PAD_SSP3_MOSI__AUART4_RX 0x2191
-MX28_PAD_SSP3_MISO__AUART4_RTS 0x21a1
-MX28_PAD_SSP3_SS0__AUART4_CTS 0x21b1
-MX28_PAD_AUART0_RX__I2C0_SCL 0x3001
-MX28_PAD_AUART0_TX__I2C0_SDA 0x3011
-MX28_PAD_AUART0_CTS__AUART4_RX 0x3021
-MX28_PAD_AUART0_RTS__AUART4_TX 0x3031
-MX28_PAD_AUART1_RX__SSP2_CARD_DETECT 0x3041
-MX28_PAD_AUART1_TX__SSP3_CARD_DETECT 0x3051
-MX28_PAD_AUART1_CTS__USB0_OVERCURRENT 0x3061
-MX28_PAD_AUART1_RTS__USB0_ID 0x3071
-MX28_PAD_AUART2_RX__SSP3_D1 0x3081
-MX28_PAD_AUART2_TX__SSP3_D2 0x3091
-MX28_PAD_AUART2_CTS__I2C1_SCL 0x30a1
-MX28_PAD_AUART2_RTS__I2C1_SDA 0x30b1
-MX28_PAD_AUART3_RX__CAN0_TX 0x30c1
-MX28_PAD_AUART3_TX__CAN0_RX 0x30d1
-MX28_PAD_AUART3_CTS__CAN1_TX 0x30e1
-MX28_PAD_AUART3_RTS__CAN1_RX 0x30f1
-MX28_PAD_PWM0__I2C1_SCL 0x3101
-MX28_PAD_PWM1__I2C1_SDA 0x3111
-MX28_PAD_PWM2__USB0_ID 0x3121
-MX28_PAD_SAIF0_MCLK__PWM_3 0x3141
-MX28_PAD_SAIF0_LRCLK__PWM_4 0x3151
-MX28_PAD_SAIF0_BITCLK__PWM_5 0x3161
-MX28_PAD_SAIF0_SDATA0__PWM_6 0x3171
-MX28_PAD_I2C0_SCL__TIMROT_ROTARYA 0x3181
-MX28_PAD_I2C0_SDA__TIMROT_ROTARYB 0x3191
-MX28_PAD_SAIF1_SDATA0__PWM_7 0x31a1
-MX28_PAD_LCD_RESET__LCD_VSYNC 0x31e1
-MX28_PAD_ENET0_MDC__GPMI_CE4N 0x4001
-MX28_PAD_ENET0_MDIO__GPMI_CE5N 0x4011
-MX28_PAD_ENET0_RX_EN__GPMI_CE6N 0x4021
-MX28_PAD_ENET0_RXD0__GPMI_CE7N 0x4031
-MX28_PAD_ENET0_RXD1__GPMI_READY4 0x4041
-MX28_PAD_ENET0_TX_CLK__HSADC_TRIGGER 0x4051
-MX28_PAD_ENET0_TX_EN__GPMI_READY5 0x4061
-MX28_PAD_ENET0_TXD0__GPMI_READY6 0x4071
-MX28_PAD_ENET0_TXD1__GPMI_READY7 0x4081
-MX28_PAD_ENET0_RXD2__ENET1_RXD0 0x4091
-MX28_PAD_ENET0_RXD3__ENET1_RXD1 0x40a1
-MX28_PAD_ENET0_TXD2__ENET1_TXD0 0x40b1
-MX28_PAD_ENET0_TXD3__ENET1_TXD1 0x40c1
-MX28_PAD_ENET0_RX_CLK__ENET0_RX_ER 0x40d1
-MX28_PAD_ENET0_COL__ENET1_TX_EN 0x40e1
-MX28_PAD_ENET0_CRS__ENET1_RX_EN 0x40f1
-MX28_PAD_GPMI_CE2N__ENET0_RX_ER 0x0122
-MX28_PAD_GPMI_CE3N__SAIF1_MCLK 0x0132
-MX28_PAD_GPMI_RDY0__USB0_ID 0x0142
-MX28_PAD_GPMI_RDY2__ENET0_TX_ER 0x0162
-MX28_PAD_GPMI_RDY3__HSADC_TRIGGER 0x0172
-MX28_PAD_GPMI_ALE__SSP3_D4 0x01a2
-MX28_PAD_GPMI_CLE__SSP3_D5 0x01b2
-MX28_PAD_LCD_D00__ETM_DA0 0x1002
-MX28_PAD_LCD_D01__ETM_DA1 0x1012
-MX28_PAD_LCD_D02__ETM_DA2 0x1022
-MX28_PAD_LCD_D03__ETM_DA3 0x1032
-MX28_PAD_LCD_D04__ETM_DA4 0x1042
-MX28_PAD_LCD_D05__ETM_DA5 0x1052
-MX28_PAD_LCD_D06__ETM_DA6 0x1062
-MX28_PAD_LCD_D07__ETM_DA7 0x1072
-MX28_PAD_LCD_D08__ETM_DA8 0x1082
-MX28_PAD_LCD_D09__ETM_DA9 0x1092
-MX28_PAD_LCD_D10__ETM_DA10 0x10a2
-MX28_PAD_LCD_D11__ETM_DA11 0x10b2
-MX28_PAD_LCD_D12__ETM_DA12 0x10c2
-MX28_PAD_LCD_D13__ETM_DA13 0x10d2
-MX28_PAD_LCD_D14__ETM_DA14 0x10e2
-MX28_PAD_LCD_D15__ETM_DA15 0x10f2
-MX28_PAD_LCD_D16__ETM_DA7 0x1102
-MX28_PAD_LCD_D17__ETM_DA6 0x1112
-MX28_PAD_LCD_D18__ETM_DA5 0x1122
-MX28_PAD_LCD_D19__ETM_DA4 0x1132
-MX28_PAD_LCD_D20__ETM_DA3 0x1142
-MX28_PAD_LCD_D21__ETM_DA2 0x1152
-MX28_PAD_LCD_D22__ETM_DA1 0x1162
-MX28_PAD_LCD_D23__ETM_DA0 0x1172
-MX28_PAD_LCD_RD_E__ETM_TCTL 0x1182
-MX28_PAD_LCD_WR_RWN__ETM_TCLK 0x1192
-MX28_PAD_LCD_HSYNC__ETM_TCTL 0x11d2
-MX28_PAD_LCD_DOTCLK__ETM_TCLK 0x11e2
-MX28_PAD_SSP1_SCK__ENET0_1588_EVENT2_OUT 0x20c2
-MX28_PAD_SSP1_CMD__ENET0_1588_EVENT2_IN 0x20d2
-MX28_PAD_SSP1_DATA0__ENET0_1588_EVENT3_OUT 0x20e2
-MX28_PAD_SSP1_DATA3__ENET0_1588_EVENT3_IN 0x20f2
-MX28_PAD_SSP2_SCK__SAIF0_SDATA1 0x2102
-MX28_PAD_SSP2_MOSI__SAIF0_SDATA2 0x2112
-MX28_PAD_SSP2_MISO__SAIF1_SDATA1 0x2122
-MX28_PAD_SSP2_SS0__SAIF1_SDATA2 0x2132
-MX28_PAD_SSP2_SS1__USB1_OVERCURRENT 0x2142
-MX28_PAD_SSP2_SS2__USB0_OVERCURRENT 0x2152
-MX28_PAD_SSP3_SCK__ENET1_1588_EVENT0_OUT 0x2182
-MX28_PAD_SSP3_MOSI__ENET1_1588_EVENT0_IN 0x2192
-MX28_PAD_SSP3_MISO__ENET1_1588_EVENT1_OUT 0x21a2
-MX28_PAD_SSP3_SS0__ENET1_1588_EVENT1_IN 0x21b2
-MX28_PAD_AUART0_RX__DUART_CTS 0x3002
-MX28_PAD_AUART0_TX__DUART_RTS 0x3012
-MX28_PAD_AUART0_CTS__DUART_RX 0x3022
-MX28_PAD_AUART0_RTS__DUART_TX 0x3032
-MX28_PAD_AUART1_RX__PWM_0 0x3042
-MX28_PAD_AUART1_TX__PWM_1 0x3052
-MX28_PAD_AUART1_CTS__TIMROT_ROTARYA 0x3062
-MX28_PAD_AUART1_RTS__TIMROT_ROTARYB 0x3072
-MX28_PAD_AUART2_RX__SSP3_D4 0x3082
-MX28_PAD_AUART2_TX__SSP3_D5 0x3092
-MX28_PAD_AUART2_CTS__SAIF1_BITCLK 0x30a2
-MX28_PAD_AUART2_RTS__SAIF1_LRCLK 0x30b2
-MX28_PAD_AUART3_RX__ENET0_1588_EVENT0_OUT 0x30c2
-MX28_PAD_AUART3_TX__ENET0_1588_EVENT0_IN 0x30d2
-MX28_PAD_AUART3_CTS__ENET0_1588_EVENT1_OUT 0x30e2
-MX28_PAD_AUART3_RTS__ENET0_1588_EVENT1_IN 0x30f2
-MX28_PAD_PWM0__DUART_RX 0x3102
-MX28_PAD_PWM1__DUART_TX 0x3112
-MX28_PAD_PWM2__USB1_OVERCURRENT 0x3122
-MX28_PAD_SAIF0_MCLK__AUART4_CTS 0x3142
-MX28_PAD_SAIF0_LRCLK__AUART4_RTS 0x3152
-MX28_PAD_SAIF0_BITCLK__AUART4_RX 0x3162
-MX28_PAD_SAIF0_SDATA0__AUART4_TX 0x3172
-MX28_PAD_I2C0_SCL__DUART_RX 0x3182
-MX28_PAD_I2C0_SDA__DUART_TX 0x3192
-MX28_PAD_SAIF1_SDATA0__SAIF0_SDATA1 0x31a2
-MX28_PAD_SPDIF__ENET1_RX_ER 0x31b2
-MX28_PAD_ENET0_MDC__SAIF0_SDATA1 0x4002
-MX28_PAD_ENET0_MDIO__SAIF0_SDATA2 0x4012
-MX28_PAD_ENET0_RX_EN__SAIF1_SDATA1 0x4022
-MX28_PAD_ENET0_RXD0__SAIF1_SDATA2 0x4032
-MX28_PAD_ENET0_TX_CLK__ENET0_1588_EVENT2_OUT 0x4052
-MX28_PAD_ENET0_RXD2__ENET0_1588_EVENT0_OUT 0x4092
-MX28_PAD_ENET0_RXD3__ENET0_1588_EVENT0_IN 0x40a2
-MX28_PAD_ENET0_TXD2__ENET0_1588_EVENT1_OUT 0x40b2
-MX28_PAD_ENET0_TXD3__ENET0_1588_EVENT1_IN 0x40c2
-MX28_PAD_ENET0_RX_CLK__ENET0_1588_EVENT2_IN 0x40d2
-MX28_PAD_ENET0_COL__ENET0_1588_EVENT3_OUT 0x40e2
-MX28_PAD_ENET0_CRS__ENET0_1588_EVENT3_IN 0x40f2
-MX28_PAD_GPMI_D00__GPIO_0_0 0x0003
-MX28_PAD_GPMI_D01__GPIO_0_1 0x0013
-MX28_PAD_GPMI_D02__GPIO_0_2 0x0023
-MX28_PAD_GPMI_D03__GPIO_0_3 0x0033
-MX28_PAD_GPMI_D04__GPIO_0_4 0x0043
-MX28_PAD_GPMI_D05__GPIO_0_5 0x0053
-MX28_PAD_GPMI_D06__GPIO_0_6 0x0063
-MX28_PAD_GPMI_D07__GPIO_0_7 0x0073
-MX28_PAD_GPMI_CE0N__GPIO_0_16 0x0103
-MX28_PAD_GPMI_CE1N__GPIO_0_17 0x0113
-MX28_PAD_GPMI_CE2N__GPIO_0_18 0x0123
-MX28_PAD_GPMI_CE3N__GPIO_0_19 0x0133
-MX28_PAD_GPMI_RDY0__GPIO_0_20 0x0143
-MX28_PAD_GPMI_RDY1__GPIO_0_21 0x0153
-MX28_PAD_GPMI_RDY2__GPIO_0_22 0x0163
-MX28_PAD_GPMI_RDY3__GPIO_0_23 0x0173
-MX28_PAD_GPMI_RDN__GPIO_0_24 0x0183
-MX28_PAD_GPMI_WRN__GPIO_0_25 0x0193
-MX28_PAD_GPMI_ALE__GPIO_0_26 0x01a3
-MX28_PAD_GPMI_CLE__GPIO_0_27 0x01b3
-MX28_PAD_GPMI_RESETN__GPIO_0_28 0x01c3
-MX28_PAD_LCD_D00__GPIO_1_0 0x1003
-MX28_PAD_LCD_D01__GPIO_1_1 0x1013
-MX28_PAD_LCD_D02__GPIO_1_2 0x1023
-MX28_PAD_LCD_D03__GPIO_1_3 0x1033
-MX28_PAD_LCD_D04__GPIO_1_4 0x1043
-MX28_PAD_LCD_D05__GPIO_1_5 0x1053
-MX28_PAD_LCD_D06__GPIO_1_6 0x1063
-MX28_PAD_LCD_D07__GPIO_1_7 0x1073
-MX28_PAD_LCD_D08__GPIO_1_8 0x1083
-MX28_PAD_LCD_D09__GPIO_1_9 0x1093
-MX28_PAD_LCD_D10__GPIO_1_10 0x10a3
-MX28_PAD_LCD_D11__GPIO_1_11 0x10b3
-MX28_PAD_LCD_D12__GPIO_1_12 0x10c3
-MX28_PAD_LCD_D13__GPIO_1_13 0x10d3
-MX28_PAD_LCD_D14__GPIO_1_14 0x10e3
-MX28_PAD_LCD_D15__GPIO_1_15 0x10f3
-MX28_PAD_LCD_D16__GPIO_1_16 0x1103
-MX28_PAD_LCD_D17__GPIO_1_17 0x1113
-MX28_PAD_LCD_D18__GPIO_1_18 0x1123
-MX28_PAD_LCD_D19__GPIO_1_19 0x1133
-MX28_PAD_LCD_D20__GPIO_1_20 0x1143
-MX28_PAD_LCD_D21__GPIO_1_21 0x1153
-MX28_PAD_LCD_D22__GPIO_1_22 0x1163
-MX28_PAD_LCD_D23__GPIO_1_23 0x1173
-MX28_PAD_LCD_RD_E__GPIO_1_24 0x1183
-MX28_PAD_LCD_WR_RWN__GPIO_1_25 0x1193
-MX28_PAD_LCD_RS__GPIO_1_26 0x11a3
-MX28_PAD_LCD_CS__GPIO_1_27 0x11b3
-MX28_PAD_LCD_VSYNC__GPIO_1_28 0x11c3
-MX28_PAD_LCD_HSYNC__GPIO_1_29 0x11d3
-MX28_PAD_LCD_DOTCLK__GPIO_1_30 0x11e3
-MX28_PAD_LCD_ENABLE__GPIO_1_31 0x11f3
-MX28_PAD_SSP0_DATA0__GPIO_2_0 0x2003
-MX28_PAD_SSP0_DATA1__GPIO_2_1 0x2013
-MX28_PAD_SSP0_DATA2__GPIO_2_2 0x2023
-MX28_PAD_SSP0_DATA3__GPIO_2_3 0x2033
-MX28_PAD_SSP0_DATA4__GPIO_2_4 0x2043
-MX28_PAD_SSP0_DATA5__GPIO_2_5 0x2053
-MX28_PAD_SSP0_DATA6__GPIO_2_6 0x2063
-MX28_PAD_SSP0_DATA7__GPIO_2_7 0x2073
-MX28_PAD_SSP0_CMD__GPIO_2_8 0x2083
-MX28_PAD_SSP0_DETECT__GPIO_2_9 0x2093
-MX28_PAD_SSP0_SCK__GPIO_2_10 0x20a3
-MX28_PAD_SSP1_SCK__GPIO_2_12 0x20c3
-MX28_PAD_SSP1_CMD__GPIO_2_13 0x20d3
-MX28_PAD_SSP1_DATA0__GPIO_2_14 0x20e3
-MX28_PAD_SSP1_DATA3__GPIO_2_15 0x20f3
-MX28_PAD_SSP2_SCK__GPIO_2_16 0x2103
-MX28_PAD_SSP2_MOSI__GPIO_2_17 0x2113
-MX28_PAD_SSP2_MISO__GPIO_2_18 0x2123
-MX28_PAD_SSP2_SS0__GPIO_2_19 0x2133
-MX28_PAD_SSP2_SS1__GPIO_2_20 0x2143
-MX28_PAD_SSP2_SS2__GPIO_2_21 0x2153
-MX28_PAD_SSP3_SCK__GPIO_2_24 0x2183
-MX28_PAD_SSP3_MOSI__GPIO_2_25 0x2193
-MX28_PAD_SSP3_MISO__GPIO_2_26 0x21a3
-MX28_PAD_SSP3_SS0__GPIO_2_27 0x21b3
-MX28_PAD_AUART0_RX__GPIO_3_0 0x3003
-MX28_PAD_AUART0_TX__GPIO_3_1 0x3013
-MX28_PAD_AUART0_CTS__GPIO_3_2 0x3023
-MX28_PAD_AUART0_RTS__GPIO_3_3 0x3033
-MX28_PAD_AUART1_RX__GPIO_3_4 0x3043
-MX28_PAD_AUART1_TX__GPIO_3_5 0x3053
-MX28_PAD_AUART1_CTS__GPIO_3_6 0x3063
-MX28_PAD_AUART1_RTS__GPIO_3_7 0x3073
-MX28_PAD_AUART2_RX__GPIO_3_8 0x3083
-MX28_PAD_AUART2_TX__GPIO_3_9 0x3093
-MX28_PAD_AUART2_CTS__GPIO_3_10 0x30a3
-MX28_PAD_AUART2_RTS__GPIO_3_11 0x30b3
-MX28_PAD_AUART3_RX__GPIO_3_12 0x30c3
-MX28_PAD_AUART3_TX__GPIO_3_13 0x30d3
-MX28_PAD_AUART3_CTS__GPIO_3_14 0x30e3
-MX28_PAD_AUART3_RTS__GPIO_3_15 0x30f3
-MX28_PAD_PWM0__GPIO_3_16 0x3103
-MX28_PAD_PWM1__GPIO_3_17 0x3113
-MX28_PAD_PWM2__GPIO_3_18 0x3123
-MX28_PAD_SAIF0_MCLK__GPIO_3_20 0x3143
-MX28_PAD_SAIF0_LRCLK__GPIO_3_21 0x3153
-MX28_PAD_SAIF0_BITCLK__GPIO_3_22 0x3163
-MX28_PAD_SAIF0_SDATA0__GPIO_3_23 0x3173
-MX28_PAD_I2C0_SCL__GPIO_3_24 0x3183
-MX28_PAD_I2C0_SDA__GPIO_3_25 0x3193
-MX28_PAD_SAIF1_SDATA0__GPIO_3_26 0x31a3
-MX28_PAD_SPDIF__GPIO_3_27 0x31b3
-MX28_PAD_PWM3__GPIO_3_28 0x31c3
-MX28_PAD_PWM4__GPIO_3_29 0x31d3
-MX28_PAD_LCD_RESET__GPIO_3_30 0x31e3
-MX28_PAD_ENET0_MDC__GPIO_4_0 0x4003
-MX28_PAD_ENET0_MDIO__GPIO_4_1 0x4013
-MX28_PAD_ENET0_RX_EN__GPIO_4_2 0x4023
-MX28_PAD_ENET0_RXD0__GPIO_4_3 0x4033
-MX28_PAD_ENET0_RXD1__GPIO_4_4 0x4043
-MX28_PAD_ENET0_TX_CLK__GPIO_4_5 0x4053
-MX28_PAD_ENET0_TX_EN__GPIO_4_6 0x4063
-MX28_PAD_ENET0_TXD0__GPIO_4_7 0x4073
-MX28_PAD_ENET0_TXD1__GPIO_4_8 0x4083
-MX28_PAD_ENET0_RXD2__GPIO_4_9 0x4093
-MX28_PAD_ENET0_RXD3__GPIO_4_10 0x40a3
-MX28_PAD_ENET0_TXD2__GPIO_4_11 0x40b3
-MX28_PAD_ENET0_TXD3__GPIO_4_12 0x40c3
-MX28_PAD_ENET0_RX_CLK__GPIO_4_13 0x40d3
-MX28_PAD_ENET0_COL__GPIO_4_14 0x40e3
-MX28_PAD_ENET0_CRS__GPIO_4_15 0x40f3
-MX28_PAD_ENET_CLK__GPIO_4_16 0x4103
-MX28_PAD_JTAG_RTCK__GPIO_4_20 0x4143
-
-Valid values for i.MX23 pinmux-id:
-
-pinmux id
------- --
-MX23_PAD_GPMI_D00__GPMI_D00 0x0000
-MX23_PAD_GPMI_D01__GPMI_D01 0x0010
-MX23_PAD_GPMI_D02__GPMI_D02 0x0020
-MX23_PAD_GPMI_D03__GPMI_D03 0x0030
-MX23_PAD_GPMI_D04__GPMI_D04 0x0040
-MX23_PAD_GPMI_D05__GPMI_D05 0x0050
-MX23_PAD_GPMI_D06__GPMI_D06 0x0060
-MX23_PAD_GPMI_D07__GPMI_D07 0x0070
-MX23_PAD_GPMI_D08__GPMI_D08 0x0080
-MX23_PAD_GPMI_D09__GPMI_D09 0x0090
-MX23_PAD_GPMI_D10__GPMI_D10 0x00a0
-MX23_PAD_GPMI_D11__GPMI_D11 0x00b0
-MX23_PAD_GPMI_D12__GPMI_D12 0x00c0
-MX23_PAD_GPMI_D13__GPMI_D13 0x00d0
-MX23_PAD_GPMI_D14__GPMI_D14 0x00e0
-MX23_PAD_GPMI_D15__GPMI_D15 0x00f0
-MX23_PAD_GPMI_CLE__GPMI_CLE 0x0100
-MX23_PAD_GPMI_ALE__GPMI_ALE 0x0110
-MX23_PAD_GPMI_CE2N__GPMI_CE2N 0x0120
-MX23_PAD_GPMI_RDY0__GPMI_RDY0 0x0130
-MX23_PAD_GPMI_RDY1__GPMI_RDY1 0x0140
-MX23_PAD_GPMI_RDY2__GPMI_RDY2 0x0150
-MX23_PAD_GPMI_RDY3__GPMI_RDY3 0x0160
-MX23_PAD_GPMI_WPN__GPMI_WPN 0x0170
-MX23_PAD_GPMI_WRN__GPMI_WRN 0x0180
-MX23_PAD_GPMI_RDN__GPMI_RDN 0x0190
-MX23_PAD_AUART1_CTS__AUART1_CTS 0x01a0
-MX23_PAD_AUART1_RTS__AUART1_RTS 0x01b0
-MX23_PAD_AUART1_RX__AUART1_RX 0x01c0
-MX23_PAD_AUART1_TX__AUART1_TX 0x01d0
-MX23_PAD_I2C_SCL__I2C_SCL 0x01e0
-MX23_PAD_I2C_SDA__I2C_SDA 0x01f0
-MX23_PAD_LCD_D00__LCD_D00 0x1000
-MX23_PAD_LCD_D01__LCD_D01 0x1010
-MX23_PAD_LCD_D02__LCD_D02 0x1020
-MX23_PAD_LCD_D03__LCD_D03 0x1030
-MX23_PAD_LCD_D04__LCD_D04 0x1040
-MX23_PAD_LCD_D05__LCD_D05 0x1050
-MX23_PAD_LCD_D06__LCD_D06 0x1060
-MX23_PAD_LCD_D07__LCD_D07 0x1070
-MX23_PAD_LCD_D08__LCD_D08 0x1080
-MX23_PAD_LCD_D09__LCD_D09 0x1090
-MX23_PAD_LCD_D10__LCD_D10 0x10a0
-MX23_PAD_LCD_D11__LCD_D11 0x10b0
-MX23_PAD_LCD_D12__LCD_D12 0x10c0
-MX23_PAD_LCD_D13__LCD_D13 0x10d0
-MX23_PAD_LCD_D14__LCD_D14 0x10e0
-MX23_PAD_LCD_D15__LCD_D15 0x10f0
-MX23_PAD_LCD_D16__LCD_D16 0x1100
-MX23_PAD_LCD_D17__LCD_D17 0x1110
-MX23_PAD_LCD_RESET__LCD_RESET 0x1120
-MX23_PAD_LCD_RS__LCD_RS 0x1130
-MX23_PAD_LCD_WR__LCD_WR 0x1140
-MX23_PAD_LCD_CS__LCD_CS 0x1150
-MX23_PAD_LCD_DOTCK__LCD_DOTCK 0x1160
-MX23_PAD_LCD_ENABLE__LCD_ENABLE 0x1170
-MX23_PAD_LCD_HSYNC__LCD_HSYNC 0x1180
-MX23_PAD_LCD_VSYNC__LCD_VSYNC 0x1190
-MX23_PAD_PWM0__PWM0 0x11a0
-MX23_PAD_PWM1__PWM1 0x11b0
-MX23_PAD_PWM2__PWM2 0x11c0
-MX23_PAD_PWM3__PWM3 0x11d0
-MX23_PAD_PWM4__PWM4 0x11e0
-MX23_PAD_SSP1_CMD__SSP1_CMD 0x2000
-MX23_PAD_SSP1_DETECT__SSP1_DETECT 0x2010
-MX23_PAD_SSP1_DATA0__SSP1_DATA0 0x2020
-MX23_PAD_SSP1_DATA1__SSP1_DATA1 0x2030
-MX23_PAD_SSP1_DATA2__SSP1_DATA2 0x2040
-MX23_PAD_SSP1_DATA3__SSP1_DATA3 0x2050
-MX23_PAD_SSP1_SCK__SSP1_SCK 0x2060
-MX23_PAD_ROTARYA__ROTARYA 0x2070
-MX23_PAD_ROTARYB__ROTARYB 0x2080
-MX23_PAD_EMI_A00__EMI_A00 0x2090
-MX23_PAD_EMI_A01__EMI_A01 0x20a0
-MX23_PAD_EMI_A02__EMI_A02 0x20b0
-MX23_PAD_EMI_A03__EMI_A03 0x20c0
-MX23_PAD_EMI_A04__EMI_A04 0x20d0
-MX23_PAD_EMI_A05__EMI_A05 0x20e0
-MX23_PAD_EMI_A06__EMI_A06 0x20f0
-MX23_PAD_EMI_A07__EMI_A07 0x2100
-MX23_PAD_EMI_A08__EMI_A08 0x2110
-MX23_PAD_EMI_A09__EMI_A09 0x2120
-MX23_PAD_EMI_A10__EMI_A10 0x2130
-MX23_PAD_EMI_A11__EMI_A11 0x2140
-MX23_PAD_EMI_A12__EMI_A12 0x2150
-MX23_PAD_EMI_BA0__EMI_BA0 0x2160
-MX23_PAD_EMI_BA1__EMI_BA1 0x2170
-MX23_PAD_EMI_CASN__EMI_CASN 0x2180
-MX23_PAD_EMI_CE0N__EMI_CE0N 0x2190
-MX23_PAD_EMI_CE1N__EMI_CE1N 0x21a0
-MX23_PAD_GPMI_CE1N__GPMI_CE1N 0x21b0
-MX23_PAD_GPMI_CE0N__GPMI_CE0N 0x21c0
-MX23_PAD_EMI_CKE__EMI_CKE 0x21d0
-MX23_PAD_EMI_RASN__EMI_RASN 0x21e0
-MX23_PAD_EMI_WEN__EMI_WEN 0x21f0
-MX23_PAD_EMI_D00__EMI_D00 0x3000
-MX23_PAD_EMI_D01__EMI_D01 0x3010
-MX23_PAD_EMI_D02__EMI_D02 0x3020
-MX23_PAD_EMI_D03__EMI_D03 0x3030
-MX23_PAD_EMI_D04__EMI_D04 0x3040
-MX23_PAD_EMI_D05__EMI_D05 0x3050
-MX23_PAD_EMI_D06__EMI_D06 0x3060
-MX23_PAD_EMI_D07__EMI_D07 0x3070
-MX23_PAD_EMI_D08__EMI_D08 0x3080
-MX23_PAD_EMI_D09__EMI_D09 0x3090
-MX23_PAD_EMI_D10__EMI_D10 0x30a0
-MX23_PAD_EMI_D11__EMI_D11 0x30b0
-MX23_PAD_EMI_D12__EMI_D12 0x30c0
-MX23_PAD_EMI_D13__EMI_D13 0x30d0
-MX23_PAD_EMI_D14__EMI_D14 0x30e0
-MX23_PAD_EMI_D15__EMI_D15 0x30f0
-MX23_PAD_EMI_DQM0__EMI_DQM0 0x3100
-MX23_PAD_EMI_DQM1__EMI_DQM1 0x3110
-MX23_PAD_EMI_DQS0__EMI_DQS0 0x3120
-MX23_PAD_EMI_DQS1__EMI_DQS1 0x3130
-MX23_PAD_EMI_CLK__EMI_CLK 0x3140
-MX23_PAD_EMI_CLKN__EMI_CLKN 0x3150
-MX23_PAD_GPMI_D00__LCD_D8 0x0001
-MX23_PAD_GPMI_D01__LCD_D9 0x0011
-MX23_PAD_GPMI_D02__LCD_D10 0x0021
-MX23_PAD_GPMI_D03__LCD_D11 0x0031
-MX23_PAD_GPMI_D04__LCD_D12 0x0041
-MX23_PAD_GPMI_D05__LCD_D13 0x0051
-MX23_PAD_GPMI_D06__LCD_D14 0x0061
-MX23_PAD_GPMI_D07__LCD_D15 0x0071
-MX23_PAD_GPMI_D08__LCD_D18 0x0081
-MX23_PAD_GPMI_D09__LCD_D19 0x0091
-MX23_PAD_GPMI_D10__LCD_D20 0x00a1
-MX23_PAD_GPMI_D11__LCD_D21 0x00b1
-MX23_PAD_GPMI_D12__LCD_D22 0x00c1
-MX23_PAD_GPMI_D13__LCD_D23 0x00d1
-MX23_PAD_GPMI_D14__AUART2_RX 0x00e1
-MX23_PAD_GPMI_D15__AUART2_TX 0x00f1
-MX23_PAD_GPMI_CLE__LCD_D16 0x0101
-MX23_PAD_GPMI_ALE__LCD_D17 0x0111
-MX23_PAD_GPMI_CE2N__ATA_A2 0x0121
-MX23_PAD_AUART1_RTS__IR_CLK 0x01b1
-MX23_PAD_AUART1_RX__IR_RX 0x01c1
-MX23_PAD_AUART1_TX__IR_TX 0x01d1
-MX23_PAD_I2C_SCL__GPMI_RDY2 0x01e1
-MX23_PAD_I2C_SDA__GPMI_CE2N 0x01f1
-MX23_PAD_LCD_D00__ETM_DA8 0x1001
-MX23_PAD_LCD_D01__ETM_DA9 0x1011
-MX23_PAD_LCD_D02__ETM_DA10 0x1021
-MX23_PAD_LCD_D03__ETM_DA11 0x1031
-MX23_PAD_LCD_D04__ETM_DA12 0x1041
-MX23_PAD_LCD_D05__ETM_DA13 0x1051
-MX23_PAD_LCD_D06__ETM_DA14 0x1061
-MX23_PAD_LCD_D07__ETM_DA15 0x1071
-MX23_PAD_LCD_D08__ETM_DA0 0x1081
-MX23_PAD_LCD_D09__ETM_DA1 0x1091
-MX23_PAD_LCD_D10__ETM_DA2 0x10a1
-MX23_PAD_LCD_D11__ETM_DA3 0x10b1
-MX23_PAD_LCD_D12__ETM_DA4 0x10c1
-MX23_PAD_LCD_D13__ETM_DA5 0x10d1
-MX23_PAD_LCD_D14__ETM_DA6 0x10e1
-MX23_PAD_LCD_D15__ETM_DA7 0x10f1
-MX23_PAD_LCD_RESET__ETM_TCTL 0x1121
-MX23_PAD_LCD_RS__ETM_TCLK 0x1131
-MX23_PAD_LCD_DOTCK__GPMI_RDY3 0x1161
-MX23_PAD_LCD_ENABLE__I2C_SCL 0x1171
-MX23_PAD_LCD_HSYNC__I2C_SDA 0x1181
-MX23_PAD_LCD_VSYNC__LCD_BUSY 0x1191
-MX23_PAD_PWM0__ROTARYA 0x11a1
-MX23_PAD_PWM1__ROTARYB 0x11b1
-MX23_PAD_PWM2__GPMI_RDY3 0x11c1
-MX23_PAD_PWM3__ETM_TCTL 0x11d1
-MX23_PAD_PWM4__ETM_TCLK 0x11e1
-MX23_PAD_SSP1_DETECT__GPMI_CE3N 0x2011
-MX23_PAD_SSP1_DATA1__I2C_SCL 0x2031
-MX23_PAD_SSP1_DATA2__I2C_SDA 0x2041
-MX23_PAD_ROTARYA__AUART2_RTS 0x2071
-MX23_PAD_ROTARYB__AUART2_CTS 0x2081
-MX23_PAD_GPMI_D00__SSP2_DATA0 0x0002
-MX23_PAD_GPMI_D01__SSP2_DATA1 0x0012
-MX23_PAD_GPMI_D02__SSP2_DATA2 0x0022
-MX23_PAD_GPMI_D03__SSP2_DATA3 0x0032
-MX23_PAD_GPMI_D04__SSP2_DATA4 0x0042
-MX23_PAD_GPMI_D05__SSP2_DATA5 0x0052
-MX23_PAD_GPMI_D06__SSP2_DATA6 0x0062
-MX23_PAD_GPMI_D07__SSP2_DATA7 0x0072
-MX23_PAD_GPMI_D08__SSP1_DATA4 0x0082
-MX23_PAD_GPMI_D09__SSP1_DATA5 0x0092
-MX23_PAD_GPMI_D10__SSP1_DATA6 0x00a2
-MX23_PAD_GPMI_D11__SSP1_DATA7 0x00b2
-MX23_PAD_GPMI_D15__GPMI_CE3N 0x00f2
-MX23_PAD_GPMI_RDY0__SSP2_DETECT 0x0132
-MX23_PAD_GPMI_RDY1__SSP2_CMD 0x0142
-MX23_PAD_GPMI_WRN__SSP2_SCK 0x0182
-MX23_PAD_AUART1_CTS__SSP1_DATA4 0x01a2
-MX23_PAD_AUART1_RTS__SSP1_DATA5 0x01b2
-MX23_PAD_AUART1_RX__SSP1_DATA6 0x01c2
-MX23_PAD_AUART1_TX__SSP1_DATA7 0x01d2
-MX23_PAD_I2C_SCL__AUART1_TX 0x01e2
-MX23_PAD_I2C_SDA__AUART1_RX 0x01f2
-MX23_PAD_LCD_D08__SAIF2_SDATA0 0x1082
-MX23_PAD_LCD_D09__SAIF1_SDATA0 0x1092
-MX23_PAD_LCD_D10__SAIF_MCLK_BITCLK 0x10a2
-MX23_PAD_LCD_D11__SAIF_LRCLK 0x10b2
-MX23_PAD_LCD_D12__SAIF2_SDATA1 0x10c2
-MX23_PAD_LCD_D13__SAIF2_SDATA2 0x10d2
-MX23_PAD_LCD_D14__SAIF1_SDATA2 0x10e2
-MX23_PAD_LCD_D15__SAIF1_SDATA1 0x10f2
-MX23_PAD_LCD_D16__SAIF_ALT_BITCLK 0x1102
-MX23_PAD_LCD_RESET__GPMI_CE3N 0x1122
-MX23_PAD_PWM0__DUART_RX 0x11a2
-MX23_PAD_PWM1__DUART_TX 0x11b2
-MX23_PAD_PWM3__AUART1_CTS 0x11d2
-MX23_PAD_PWM4__AUART1_RTS 0x11e2
-MX23_PAD_SSP1_CMD__JTAG_TDO 0x2002
-MX23_PAD_SSP1_DETECT__USB_OTG_ID 0x2012
-MX23_PAD_SSP1_DATA0__JTAG_TDI 0x2022
-MX23_PAD_SSP1_DATA1__JTAG_TCLK 0x2032
-MX23_PAD_SSP1_DATA2__JTAG_RTCK 0x2042
-MX23_PAD_SSP1_DATA3__JTAG_TMS 0x2052
-MX23_PAD_SSP1_SCK__JTAG_TRST 0x2062
-MX23_PAD_ROTARYA__SPDIF 0x2072
-MX23_PAD_ROTARYB__GPMI_CE3N 0x2082
-MX23_PAD_GPMI_D00__GPIO_0_0 0x0003
-MX23_PAD_GPMI_D01__GPIO_0_1 0x0013
-MX23_PAD_GPMI_D02__GPIO_0_2 0x0023
-MX23_PAD_GPMI_D03__GPIO_0_3 0x0033
-MX23_PAD_GPMI_D04__GPIO_0_4 0x0043
-MX23_PAD_GPMI_D05__GPIO_0_5 0x0053
-MX23_PAD_GPMI_D06__GPIO_0_6 0x0063
-MX23_PAD_GPMI_D07__GPIO_0_7 0x0073
-MX23_PAD_GPMI_D08__GPIO_0_8 0x0083
-MX23_PAD_GPMI_D09__GPIO_0_9 0x0093
-MX23_PAD_GPMI_D10__GPIO_0_10 0x00a3
-MX23_PAD_GPMI_D11__GPIO_0_11 0x00b3
-MX23_PAD_GPMI_D12__GPIO_0_12 0x00c3
-MX23_PAD_GPMI_D13__GPIO_0_13 0x00d3
-MX23_PAD_GPMI_D14__GPIO_0_14 0x00e3
-MX23_PAD_GPMI_D15__GPIO_0_15 0x00f3
-MX23_PAD_GPMI_CLE__GPIO_0_16 0x0103
-MX23_PAD_GPMI_ALE__GPIO_0_17 0x0113
-MX23_PAD_GPMI_CE2N__GPIO_0_18 0x0123
-MX23_PAD_GPMI_RDY0__GPIO_0_19 0x0133
-MX23_PAD_GPMI_RDY1__GPIO_0_20 0x0143
-MX23_PAD_GPMI_RDY2__GPIO_0_21 0x0153
-MX23_PAD_GPMI_RDY3__GPIO_0_22 0x0163
-MX23_PAD_GPMI_WPN__GPIO_0_23 0x0173
-MX23_PAD_GPMI_WRN__GPIO_0_24 0x0183
-MX23_PAD_GPMI_RDN__GPIO_0_25 0x0193
-MX23_PAD_AUART1_CTS__GPIO_0_26 0x01a3
-MX23_PAD_AUART1_RTS__GPIO_0_27 0x01b3
-MX23_PAD_AUART1_RX__GPIO_0_28 0x01c3
-MX23_PAD_AUART1_TX__GPIO_0_29 0x01d3
-MX23_PAD_I2C_SCL__GPIO_0_30 0x01e3
-MX23_PAD_I2C_SDA__GPIO_0_31 0x01f3
-MX23_PAD_LCD_D00__GPIO_1_0 0x1003
-MX23_PAD_LCD_D01__GPIO_1_1 0x1013
-MX23_PAD_LCD_D02__GPIO_1_2 0x1023
-MX23_PAD_LCD_D03__GPIO_1_3 0x1033
-MX23_PAD_LCD_D04__GPIO_1_4 0x1043
-MX23_PAD_LCD_D05__GPIO_1_5 0x1053
-MX23_PAD_LCD_D06__GPIO_1_6 0x1063
-MX23_PAD_LCD_D07__GPIO_1_7 0x1073
-MX23_PAD_LCD_D08__GPIO_1_8 0x1083
-MX23_PAD_LCD_D09__GPIO_1_9 0x1093
-MX23_PAD_LCD_D10__GPIO_1_10 0x10a3
-MX23_PAD_LCD_D11__GPIO_1_11 0x10b3
-MX23_PAD_LCD_D12__GPIO_1_12 0x10c3
-MX23_PAD_LCD_D13__GPIO_1_13 0x10d3
-MX23_PAD_LCD_D14__GPIO_1_14 0x10e3
-MX23_PAD_LCD_D15__GPIO_1_15 0x10f3
-MX23_PAD_LCD_D16__GPIO_1_16 0x1103
-MX23_PAD_LCD_D17__GPIO_1_17 0x1113
-MX23_PAD_LCD_RESET__GPIO_1_18 0x1123
-MX23_PAD_LCD_RS__GPIO_1_19 0x1133
-MX23_PAD_LCD_WR__GPIO_1_20 0x1143
-MX23_PAD_LCD_CS__GPIO_1_21 0x1153
-MX23_PAD_LCD_DOTCK__GPIO_1_22 0x1163
-MX23_PAD_LCD_ENABLE__GPIO_1_23 0x1173
-MX23_PAD_LCD_HSYNC__GPIO_1_24 0x1183
-MX23_PAD_LCD_VSYNC__GPIO_1_25 0x1193
-MX23_PAD_PWM0__GPIO_1_26 0x11a3
-MX23_PAD_PWM1__GPIO_1_27 0x11b3
-MX23_PAD_PWM2__GPIO_1_28 0x11c3
-MX23_PAD_PWM3__GPIO_1_29 0x11d3
-MX23_PAD_PWM4__GPIO_1_30 0x11e3
-MX23_PAD_SSP1_CMD__GPIO_2_0 0x2003
-MX23_PAD_SSP1_DETECT__GPIO_2_1 0x2013
-MX23_PAD_SSP1_DATA0__GPIO_2_2 0x2023
-MX23_PAD_SSP1_DATA1__GPIO_2_3 0x2033
-MX23_PAD_SSP1_DATA2__GPIO_2_4 0x2043
-MX23_PAD_SSP1_DATA3__GPIO_2_5 0x2053
-MX23_PAD_SSP1_SCK__GPIO_2_6 0x2063
-MX23_PAD_ROTARYA__GPIO_2_7 0x2073
-MX23_PAD_ROTARYB__GPIO_2_8 0x2083
-MX23_PAD_EMI_A00__GPIO_2_9 0x2093
-MX23_PAD_EMI_A01__GPIO_2_10 0x20a3
-MX23_PAD_EMI_A02__GPIO_2_11 0x20b3
-MX23_PAD_EMI_A03__GPIO_2_12 0x20c3
-MX23_PAD_EMI_A04__GPIO_2_13 0x20d3
-MX23_PAD_EMI_A05__GPIO_2_14 0x20e3
-MX23_PAD_EMI_A06__GPIO_2_15 0x20f3
-MX23_PAD_EMI_A07__GPIO_2_16 0x2103
-MX23_PAD_EMI_A08__GPIO_2_17 0x2113
-MX23_PAD_EMI_A09__GPIO_2_18 0x2123
-MX23_PAD_EMI_A10__GPIO_2_19 0x2133
-MX23_PAD_EMI_A11__GPIO_2_20 0x2143
-MX23_PAD_EMI_A12__GPIO_2_21 0x2153
-MX23_PAD_EMI_BA0__GPIO_2_22 0x2163
-MX23_PAD_EMI_BA1__GPIO_2_23 0x2173
-MX23_PAD_EMI_CASN__GPIO_2_24 0x2183
-MX23_PAD_EMI_CE0N__GPIO_2_25 0x2193
-MX23_PAD_EMI_CE1N__GPIO_2_26 0x21a3
-MX23_PAD_GPMI_CE1N__GPIO_2_27 0x21b3
-MX23_PAD_GPMI_CE0N__GPIO_2_28 0x21c3
-MX23_PAD_EMI_CKE__GPIO_2_29 0x21d3
-MX23_PAD_EMI_RASN__GPIO_2_30 0x21e3
-MX23_PAD_EMI_WEN__GPIO_2_31 0x21f3
+Valid values for i.MX28/i.MX23 pinmux-id are defined in
+arch/arm/boot/dts/imx28-pinfunc.h and arch/arm/boot/dts/imx23-pinfunc.h.
+The definitions for the padconfig properties can be found in
+arch/arm/boot/dts/mxs-pinfunc.h.
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
index 5a02e30..7069a0b 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
@@ -72,6 +72,13 @@
/* pin base, nr pins & gpio function */
pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1>;
+- interrupt-controller : standard interrupt controller binding if using
+ interrupts for wake-up events for example. In this case pinctrl-single
+ is set up as a chained interrupt controller and the wake-up interrupts
+ can be requested by the drivers using request_irq().
+
+- #interrupt-cells : standard interrupt binding if using interrupts
+
This driver assumes that there is only one register for each pin (unless the
pinctrl-single,bit-per-mux is set), and uses the common pinctrl bindings as
specified in the pinctrl-bindings.txt document in this directory.
@@ -121,6 +128,8 @@
reg = <0x4a100040 0x0196>;
#address-cells = <1>;
#size-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
pinctrl-single,register-width = <16>;
pinctrl-single,function-mask = <0xffff>;
};
@@ -131,6 +140,8 @@
reg = <0x4a31e040 0x0038>;
#address-cells = <1>;
#size-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
pinctrl-single,register-width = <16>;
pinctrl-single,function-mask = <0xffff>;
};
diff --git a/Documentation/devicetree/bindings/usb/ux500-usb.txt b/Documentation/devicetree/bindings/usb/ux500-usb.txt
index 330d6ec..439a41c 100644
--- a/Documentation/devicetree/bindings/usb/ux500-usb.txt
+++ b/Documentation/devicetree/bindings/usb/ux500-usb.txt
@@ -15,7 +15,7 @@
Example:
usb_per5@a03e0000 {
- compatible = "stericsson,db8500-musb", "mentor,musb";
+ compatible = "stericsson,db8500-musb";
reg = <0xa03e0000 0x10000>;
interrupts = <0 23 0x4>;
interrupt-names = "mc";
diff --git a/Documentation/devicetree/bindings/video/exynos_hdmi.txt b/Documentation/devicetree/bindings/video/exynos_hdmi.txt
index 323983b..50decf8 100644
--- a/Documentation/devicetree/bindings/video/exynos_hdmi.txt
+++ b/Documentation/devicetree/bindings/video/exynos_hdmi.txt
@@ -12,7 +12,19 @@
a) phandle of the gpio controller node.
b) pin number within the gpio controller.
c) optional flags and pull up/down.
-
+- clocks: list of clock IDs from SoC clock driver.
+ a) hdmi: Gate of HDMI IP bus clock.
+ b) sclk_hdmi: Gate of HDMI special clock.
+ c) sclk_pixel: Pixel special clock, one of the two possible inputs of
+ HDMI clock mux.
+ d) sclk_hdmiphy: HDMI PHY clock output, one of two possible inputs of
+ HDMI clock mux.
+ e) mout_hdmi: It is required by the driver to switch between the 2
+ parents i.e. sclk_pixel and sclk_hdmiphy. If hdmiphy is stable
+ after configuration, parent is set to sclk_hdmiphy else
+ sclk_pixel.
+- clock-names: aliases as per driver requirements for above clock IDs:
+ "hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy" and "mout_hdmi".
Example:
hdmi {
diff --git a/Documentation/devicetree/bindings/video/exynos_mixer.txt b/Documentation/devicetree/bindings/video/exynos_mixer.txt
index 3334b0a..7bfde9c 100644
--- a/Documentation/devicetree/bindings/video/exynos_mixer.txt
+++ b/Documentation/devicetree/bindings/video/exynos_mixer.txt
@@ -10,6 +10,10 @@
- reg: physical base address of the mixer and length of memory mapped
region.
- interrupts: interrupt number to the cpu.
+- clocks: list of clock IDs from SoC clock driver.
+ a) mixer: Gate of Mixer IP bus clock.
+ b) sclk_hdmi: HDMI Special clock, one of the two possible inputs of
+ mixer mux.
Example:
diff --git a/Documentation/sound/alsa/HD-Audio-Models.txt b/Documentation/sound/alsa/HD-Audio-Models.txt
index f911e36..85c362d 100644
--- a/Documentation/sound/alsa/HD-Audio-Models.txt
+++ b/Documentation/sound/alsa/HD-Audio-Models.txt
@@ -28,6 +28,7 @@
alc269-dmic Enable ALC269(VA) digital mic workaround
alc271-dmic Enable ALC271X digital mic workaround
inv-dmic Inverted internal mic workaround
+ headset-mic Indicates a combined headset (headphone+mic) jack
lenovo-dock Enables docking station I/O for some Lenovos
dell-headset-multi Headset jack, which can also be used as mic-in
dell-headset-dock Headset jack (without mic-in), and also dock I/O
diff --git a/MAINTAINERS b/MAINTAINERS
index 8a0cbf3..cb1f2e0 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -929,7 +929,7 @@
L: linux-omap@vger.kernel.org
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
-F: arch/arm/mach-omap2/board-igep0020.c
+F: arch/arm/boot/dts/omap3-igep*
ARM/INCOME PXA270 SUPPORT
M: Marek Vasut <marek.vasut@gmail.com>
@@ -6088,6 +6088,12 @@
S: Maintained
F: drivers/gpio/gpio-omap.c
+OMAP/NEWFLOW NANOBONE MACHINE SUPPORT
+M: Mark Jackson <mpfj@newflow.co.uk>
+L: linux-omap@vger.kernel.org
+S: Maintained
+F: arch/arm/boot/dts/am335x-nano.dts
+
OMFS FILESYSTEM
M: Bob Copeland <me@bobcopeland.com>
L: linux-karma-devel@lists.sourceforge.net
diff --git a/Makefile b/Makefile
index 9de9aba..deec08b 100644
--- a/Makefile
+++ b/Makefile
@@ -1,7 +1,7 @@
VERSION = 3
PATCHLEVEL = 12
SUBLEVEL = 0
-EXTRAVERSION = -rc4
+EXTRAVERSION = -rc5
NAME = One Giant Leap for Frogkind
# *DOCUMENTATION*
diff --git a/arch/arc/kernel/ptrace.c b/arch/arc/kernel/ptrace.c
index 3332385..5d76706 100644
--- a/arch/arc/kernel/ptrace.c
+++ b/arch/arc/kernel/ptrace.c
@@ -102,7 +102,7 @@
REG_IGNORE_ONE(pad2);
REG_IN_CHUNK(callee, efa, cregs); /* callee_regs[r25..r13] */
REG_IGNORE_ONE(efa); /* efa update invalid */
- REG_IN_ONE(stop_pc, &ptregs->ret); /* stop_pc: PC update */
+ REG_IGNORE_ONE(stop_pc); /* PC updated via @ret */
return ret;
}
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 1ad6fb6..5ef8136 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -727,6 +727,7 @@
select ARM_VIC
select CLKDEV_LOOKUP
select CLKSRC_SAMSUNG_PWM
+ select COMMON_CLK
select CPU_V6
select GENERIC_CLOCKEVENTS
select GPIO_SAMSUNG
@@ -740,7 +741,6 @@
select S3C_DEV_NAND
select S3C_GPIO_TRACK
select SAMSUNG_ATAGS
- select SAMSUNG_CLKSRC
select SAMSUNG_GPIOLIB_4BIT
select SAMSUNG_WDT_RESET
select USB_ARCH_HAS_OHCI
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index a37a50f..db50b62 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -296,10 +296,15 @@
# Convert bzImage to zImage
bzImage: zImage
-zImage Image xipImage bootpImage uImage: vmlinux
+BOOT_TARGETS = zImage Image xipImage bootpImage uImage
+INSTALL_TARGETS = zinstall uinstall install
+
+PHONY += bzImage $(BOOT_TARGETS) $(INSTALL_TARGETS)
+
+$(BOOT_TARGETS): vmlinux
$(Q)$(MAKE) $(build)=$(boot) MACHINE=$(MACHINE) $(boot)/$@
-zinstall uinstall install: vmlinux
+$(INSTALL_TARGETS):
$(Q)$(MAKE) $(build)=$(boot) MACHINE=$(MACHINE) $@
%.dtb: | scripts
diff --git a/arch/arm/boot/Makefile b/arch/arm/boot/Makefile
index 84aa2ca..ec2f806 100644
--- a/arch/arm/boot/Makefile
+++ b/arch/arm/boot/Makefile
@@ -95,24 +95,24 @@
@test "$(INITRD)" != "" || \
(echo You must specify INITRD; exit -1)
-install: $(obj)/Image
- $(CONFIG_SHELL) $(srctree)/$(src)/install.sh $(KERNELRELEASE) \
+install:
+ $(CONFIG_SHELL) $(srctree)/$(src)/install.sh "$(KERNELRELEASE)" \
$(obj)/Image System.map "$(INSTALL_PATH)"
-zinstall: $(obj)/zImage
- $(CONFIG_SHELL) $(srctree)/$(src)/install.sh $(KERNELRELEASE) \
+zinstall:
+ $(CONFIG_SHELL) $(srctree)/$(src)/install.sh "$(KERNELRELEASE)" \
$(obj)/zImage System.map "$(INSTALL_PATH)"
-uinstall: $(obj)/uImage
- $(CONFIG_SHELL) $(srctree)/$(src)/install.sh $(KERNELRELEASE) \
+uinstall:
+ $(CONFIG_SHELL) $(srctree)/$(src)/install.sh "$(KERNELRELEASE)" \
$(obj)/uImage System.map "$(INSTALL_PATH)"
zi:
- $(CONFIG_SHELL) $(srctree)/$(src)/install.sh $(KERNELRELEASE) \
+ $(CONFIG_SHELL) $(srctree)/$(src)/install.sh "$(KERNELRELEASE)" \
$(obj)/zImage System.map "$(INSTALL_PATH)"
i:
- $(CONFIG_SHELL) $(srctree)/$(src)/install.sh $(KERNELRELEASE) \
+ $(CONFIG_SHELL) $(srctree)/$(src)/install.sh "$(KERNELRELEASE)" \
$(obj)/Image System.map "$(INSTALL_PATH)"
subdir- := bootp compressed dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 802720e..b590bce 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -51,6 +51,7 @@
dtb-$(CONFIG_ARCH_DOVE) += dove-cm-a510.dtb \
dove-cubox.dtb \
dove-d2plug.dtb \
+ dove-d3plug.dtb \
dove-dove-db.dtb
dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
exynos4210-smdkv310.dtb \
@@ -112,6 +113,7 @@
armada-xp-axpwifiap.dtb \
armada-xp-db.dtb \
armada-xp-gp.dtb \
+ armada-xp-matrix.dtb \
armada-xp-openblocks-ax3-4.dtb
dtb-$(CONFIG_ARCH_MXC) += \
imx25-karo-tx25.dtb \
@@ -142,8 +144,10 @@
imx6q-sabrelite.dtb \
imx6q-sabresd.dtb \
imx6q-sbc6x.dtb \
+ imx6q-udoo.dtb \
imx6q-wandboard.dtb \
imx6sl-evk.dtb \
+ vf610-cosmic.dtb \
vf610-twr.dtb
dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
imx23-olinuxino.dtb \
@@ -159,6 +163,7 @@
imx28-cfa10057.dtb \
imx28-cfa10058.dtb \
imx28-evk.dtb \
+ imx28-m28cu3.dtb \
imx28-m28evk.dtb \
imx28-sps1.dtb \
imx28-tx28.dtb
@@ -172,9 +177,15 @@
omap3-devkit8000.dtb \
omap3-beagle-xm.dtb \
omap3-evm.dtb \
+ omap3-evm-37xx.dtb \
+ omap3-n900.dtb \
+ omap3-n9.dtb \
+ omap3-n950.dtb \
omap3-tobi.dtb \
+ omap3-gta04.dtb \
omap3-igep0020.dtb \
omap3-igep0030.dtb \
+ omap3-zoom3.dtb \
omap4-panda.dtb \
omap4-panda-a4.dtb \
omap4-panda-es.dtb \
@@ -186,17 +197,24 @@
am335x-evmsk.dtb \
am335x-bone.dtb \
am335x-boneblack.dtb \
+ am335x-nano.dtb \
+ am335x-base0033.dtb \
am3517-evm.dtb \
am3517_mt_ventoux.dtb \
- am43x-epos-evm.dtb
+ am43x-epos-evm.dtb \
+ dra7-evm.dtb
dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-ethernet-disk-mini-v2.dtb
dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb
dtb-$(CONFIG_ARCH_U8500) += ste-snowball.dtb \
- ste-hrefprev60.dtb \
- ste-hrefv60plus.dtb \
+ ste-hrefprev60-stuib.dtb \
+ ste-hrefprev60-tvk.dtb \
+ ste-hrefv60plus-stuib.dtb \
+ ste-hrefv60plus-tvk.dtb \
ste-ccu8540.dtb \
ste-ccu9540.dtb
dtb-$(CONFIG_ARCH_S3C24XX) += s3c2416-smdk2416.dtb
+dtb-$(CONFIG_ARCH_S3C64XX) += s3c6410-mini6410.dtb \
+ s3c6410-smdk6410.dtb
dtb-$(CONFIG_ARCH_SHMOBILE) += emev2-kzm9d.dtb \
emev2-kzm9d-reference.dtb \
r8a7740-armadillo800eva.dtb \
@@ -213,7 +231,9 @@
r8a73a4-ape6evm-reference.dtb \
sh7372-mackerel.dtb
dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += emev2-kzm9d-reference.dtb
-dtb-$(CONFIG_ARCH_SOCFPGA) += socfpga_cyclone5.dtb \
+dtb-$(CONFIG_ARCH_SOCFPGA) += socfpga_arria5_socdk.dtb \
+ socfpga_cyclone5_socdk.dtb \
+ socfpga_cyclone5_sockit.dtb \
socfpga_vt.dtb
dtb-$(CONFIG_ARCH_SPEAR13XX) += spear1310-evb.dtb \
spear1340-evb.dtb
@@ -235,6 +255,7 @@
sun5i-a13-olinuxino.dtb \
sun6i-a31-colombus.dtb \
sun7i-a20-cubieboard2.dtb \
+ sun7i-a20-cubietruck.dtb \
sun7i-a20-olinuxino-micro.dtb
dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
tegra20-iris-512.dtb \
@@ -249,7 +270,8 @@
tegra30-beaver.dtb \
tegra30-cardhu-a02.dtb \
tegra30-cardhu-a04.dtb \
- tegra114-dalmore.dtb
+ tegra114-dalmore.dtb \
+ tegra124-venice2.dtb
dtb-$(CONFIG_ARCH_VERSATILE) += versatile-ab.dtb \
versatile-pb.dtb
dtb-$(CONFIG_ARCH_U300) += ste-u300.dtb
diff --git a/arch/arm/boot/dts/am335x-base0033.dts b/arch/arm/boot/dts/am335x-base0033.dts
new file mode 100644
index 0000000..b4f95c2
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-base0033.dts
@@ -0,0 +1,16 @@
+/*
+ * am335x-base0033.dts - Device Tree file for IGEP AQUILA EXPANSION
+ *
+ * Copyright (C) 2013 ISEE 2007 SL - http://www.isee.biz
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "am335x-igep0033.dtsi"
+
+/ {
+ model = "IGEP COM AM335x on AQUILA Expansion";
+ compatible = "isee,am335x-base0033", "isee,am335x-igep0033", "ti,am33xx";
+};
diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi b/arch/arm/boot/dts/am335x-bone-common.dtsi
index 2f66ded..e3f27ec 100644
--- a/arch/arm/boot/dts/am335x-bone-common.dtsi
+++ b/arch/arm/boot/dts/am335x-bone-common.dtsi
@@ -21,145 +21,6 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- am33xx_pinmux: pinmux@44e10800 {
- pinctrl-names = "default";
- pinctrl-0 = <&clkout2_pin>;
-
- user_leds_s0: user_leds_s0 {
- pinctrl-single,pins = <
- 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */
- 0x58 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */
- 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */
- 0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */
- >;
- };
-
- i2c0_pins: pinmux_i2c0_pins {
- pinctrl-single,pins = <
- 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
- 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
- >;
- };
-
- uart0_pins: pinmux_uart0_pins {
- pinctrl-single,pins = <
- 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
- 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
- >;
- };
-
- clkout2_pin: pinmux_clkout2_pin {
- pinctrl-single,pins = <
- 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
- >;
- };
-
- cpsw_default: cpsw_default {
- pinctrl-single,pins = <
- /* Slave 1 */
- 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */
- 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */
- 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */
- 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd3.mii1_txd3 */
- 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd2.mii1_txd2 */
- 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd1.mii1_txd1 */
- 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd0.mii1_txd0 */
- 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_txclk.mii1_txclk */
- 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */
- 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */
- 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */
- 0x13c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */
- 0x140 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */
- >;
- };
-
- cpsw_sleep: cpsw_sleep {
- pinctrl-single,pins = <
- /* Slave 1 reset value */
- 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
-
- davinci_mdio_default: davinci_mdio_default {
- pinctrl-single,pins = <
- /* MDIO */
- 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
- 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
- >;
- };
-
- davinci_mdio_sleep: davinci_mdio_sleep {
- pinctrl-single,pins = <
- /* MDIO reset value */
- 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
- };
-
- ocp {
- uart0: serial@44e09000 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins>;
-
- status = "okay";
- };
-
- musb: usb@47400000 {
- status = "okay";
-
- control@44e10000 {
- status = "okay";
- };
-
- usb-phy@47401300 {
- status = "okay";
- };
-
- usb-phy@47401b00 {
- status = "okay";
- };
-
- usb@47401000 {
- status = "okay";
- };
-
- usb@47401800 {
- status = "okay";
- dr_mode = "host";
- };
-
- dma-controller@07402000 {
- status = "okay";
- };
- };
-
- i2c0: i2c@44e0b000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
-
- status = "okay";
- clock-frequency = <400000>;
-
- tps: tps@24 {
- reg = <0x24>;
- };
-
- };
- };
-
leds {
pinctrl-names = "default";
pinctrl-0 = <&user_leds_s0>;
@@ -183,15 +44,182 @@
led@4 {
label = "beaglebone:green:usr2";
gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "cpu0";
default-state = "off";
};
led@5 {
label = "beaglebone:green:usr3";
gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc1";
default-state = "off";
};
};
+
+ vmmcsd_fixed: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vmmcsd_fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&am33xx_pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&clkout2_pin>;
+
+ user_leds_s0: user_leds_s0 {
+ pinctrl-single,pins = <
+ 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */
+ 0x58 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */
+ 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */
+ 0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */
+ >;
+ };
+
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+
+ clkout2_pin: pinmux_clkout2_pin {
+ pinctrl-single,pins = <
+ 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
+ >;
+ };
+
+ cpsw_default: cpsw_default {
+ pinctrl-single,pins = <
+ /* Slave 1 */
+ 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */
+ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */
+ 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */
+ 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd3.mii1_txd3 */
+ 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd2.mii1_txd2 */
+ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd1.mii1_txd1 */
+ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd0.mii1_txd0 */
+ 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_txclk.mii1_txclk */
+ 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */
+ 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */
+ 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */
+ 0x13c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */
+ 0x140 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */
+ >;
+ };
+
+ cpsw_sleep: cpsw_sleep {
+ pinctrl-single,pins = <
+ /* Slave 1 reset value */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ davinci_mdio_default: davinci_mdio_default {
+ pinctrl-single,pins = <
+ /* MDIO */
+ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
+
+ davinci_mdio_sleep: davinci_mdio_sleep {
+ pinctrl-single,pins = <
+ /* MDIO reset value */
+ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ 0x160 (PIN_INPUT | MUX_MODE7) /* GPIO0_6 */
+ >;
+ };
+
+ emmc_pins: pinmux_emmc_pins {
+ pinctrl-single,pins = <
+ 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
+ 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
+ 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
+ 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
+ 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
+ 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
+ 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */
+ 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */
+ 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */
+ 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */
+ >;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+
+ control@44e10000 {
+ status = "okay";
+ };
+
+ usb-phy@47401300 {
+ status = "okay";
+ };
+
+ usb-phy@47401b00 {
+ status = "okay";
+ };
+
+ usb@47401000 {
+ status = "okay";
+ };
+
+ usb@47401800 {
+ status = "okay";
+ dr_mode = "host";
+ };
+
+ dma-controller@07402000 {
+ status = "okay";
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps: tps@24 {
+ reg = <0x24>;
+ };
+
};
/include/ "tps65217.dtsi"
@@ -260,3 +288,12 @@
pinctrl-0 = <&davinci_mdio_default>;
pinctrl-1 = <&davinci_mdio_sleep>;
};
+
+&mmc1 {
+ status = "okay";
+ bus-width = <0x4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+ cd-inverted;
+};
diff --git a/arch/arm/boot/dts/am335x-bone.dts b/arch/arm/boot/dts/am335x-bone.dts
index 7993c48..94ee427 100644
--- a/arch/arm/boot/dts/am335x-bone.dts
+++ b/arch/arm/boot/dts/am335x-bone.dts
@@ -9,3 +9,21 @@
#include "am33xx.dtsi"
#include "am335x-bone-common.dtsi"
+
+&ldo3_reg {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+};
+
+&mmc1 {
+ vmmc-supply = <&ldo3_reg>;
+};
+
+&sham {
+ status = "okay";
+};
+
+&aes {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts
index 197cadf..6b71ad9 100644
--- a/arch/arm/boot/dts/am335x-boneblack.dts
+++ b/arch/arm/boot/dts/am335x-boneblack.dts
@@ -15,3 +15,64 @@
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
+
+&mmc1 {
+ vmmc-supply = <&vmmcsd_fixed>;
+};
+
+&mmc2 {
+ vmmc-supply = <&vmmcsd_fixed>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_pins>;
+ bus-width = <8>;
+ status = "okay";
+ ti,vcc-aux-disable-is-sleep;
+};
+
+&am33xx_pinmux {
+ nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
+ pinctrl-single,pins = <
+ 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
+ 0xa0 0x08 /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xa4 0x08 /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xa8 0x08 /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xac 0x08 /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xb0 0x08 /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xb4 0x08 /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xb8 0x08 /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xbc 0x08 /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xc0 0x08 /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xc4 0x08 /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xc8 0x08 /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xcc 0x08 /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xd0 0x08 /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xd4 0x08 /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xd8 0x08 /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xdc 0x08 /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xe0 0x00 /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+ 0xe4 0x00 /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+ 0xe8 0x00 /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+ 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+ >;
+ };
+ nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
+ pinctrl-single,pins = <
+ 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
+ >;
+ };
+};
+
+&lcdc {
+ status = "okay";
+};
+
+/ {
+ hdmi {
+ compatible = "ti,tilcdc,slave";
+ i2c = <&i2c0>;
+ pinctrl-names = "default", "off";
+ pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
+ pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
+ status = "okay";
+ };
+};
diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
index e8ec875..9874294 100644
--- a/arch/arm/boot/dts/am335x-evm.dts
+++ b/arch/arm/boot/dts/am335x-evm.dts
@@ -24,324 +24,6 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- am33xx_pinmux: pinmux@44e10800 {
- pinctrl-names = "default";
- pinctrl-0 = <&matrix_keypad_s0 &volume_keys_s0 &clkout2_pin>;
-
- matrix_keypad_s0: matrix_keypad_s0 {
- pinctrl-single,pins = <
- 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */
- 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a6.gpio1_22 */
- 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a9.gpio1_25 */
- 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a10.gpio1_26 */
- 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.gpio1_27 */
- >;
- };
-
- volume_keys_s0: volume_keys_s0 {
- pinctrl-single,pins = <
- 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_sclk.gpio0_2 */
- 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_d0.gpio0_3 */
- >;
- };
-
- i2c0_pins: pinmux_i2c0_pins {
- pinctrl-single,pins = <
- 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
- 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
- >;
- };
-
- i2c1_pins: pinmux_i2c1_pins {
- pinctrl-single,pins = <
- 0x158 (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_d1.i2c1_sda */
- 0x15c (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_cs0.i2c1_scl */
- >;
- };
-
- uart0_pins: pinmux_uart0_pins {
- pinctrl-single,pins = <
- 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
- 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
- >;
- };
-
- clkout2_pin: pinmux_clkout2_pin {
- pinctrl-single,pins = <
- 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
- >;
- };
-
- nandflash_pins_s0: nandflash_pins_s0 {
- pinctrl-single,pins = <
- 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */
- 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */
- 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */
- 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */
- 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */
- 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */
- 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */
- 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */
- 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */
- 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */
- 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */
- 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */
- 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */
- 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */
- 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */
- >;
- };
-
- ecap0_pins: backlight_pins {
- pinctrl-single,pins = <
- 0x164 0x0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
- >;
- };
-
- cpsw_default: cpsw_default {
- pinctrl-single,pins = <
- /* Slave 1 */
- 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */
- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */
- 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */
- 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */
- 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */
- 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */
- 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */
- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */
- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */
- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */
- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */
- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */
- >;
- };
-
- cpsw_sleep: cpsw_sleep {
- pinctrl-single,pins = <
- /* Slave 1 reset value */
- 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
-
- davinci_mdio_default: davinci_mdio_default {
- pinctrl-single,pins = <
- /* MDIO */
- 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
- 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
- >;
- };
-
- davinci_mdio_sleep: davinci_mdio_sleep {
- pinctrl-single,pins = <
- /* MDIO reset value */
- 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
- };
-
- ocp {
- uart0: serial@44e09000 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins>;
-
- status = "okay";
- };
-
- i2c0: i2c@44e0b000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
-
- status = "okay";
- clock-frequency = <400000>;
-
- tps: tps@2d {
- reg = <0x2d>;
- };
- };
-
- musb: usb@47400000 {
- status = "okay";
-
- control@44e10000 {
- status = "okay";
- };
-
- usb-phy@47401300 {
- status = "okay";
- };
-
- usb-phy@47401b00 {
- status = "okay";
- };
-
- usb@47401000 {
- status = "okay";
- };
-
- usb@47401800 {
- status = "okay";
- dr_mode = "host";
- };
-
- dma-controller@07402000 {
- status = "okay";
- };
- };
-
- i2c1: i2c@4802a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
-
- status = "okay";
- clock-frequency = <100000>;
-
- lis331dlh: lis331dlh@18 {
- compatible = "st,lis331dlh", "st,lis3lv02d";
- reg = <0x18>;
- Vdd-supply = <&lis3_reg>;
- Vdd_IO-supply = <&lis3_reg>;
-
- st,click-single-x;
- st,click-single-y;
- st,click-single-z;
- st,click-thresh-x = <10>;
- st,click-thresh-y = <10>;
- st,click-thresh-z = <10>;
- st,irq1-click;
- st,irq2-click;
- st,wakeup-x-lo;
- st,wakeup-x-hi;
- st,wakeup-y-lo;
- st,wakeup-y-hi;
- st,wakeup-z-lo;
- st,wakeup-z-hi;
- st,min-limit-x = <120>;
- st,min-limit-y = <120>;
- st,min-limit-z = <140>;
- st,max-limit-x = <550>;
- st,max-limit-y = <550>;
- st,max-limit-z = <750>;
- };
-
- tsl2550: tsl2550@39 {
- compatible = "taos,tsl2550";
- reg = <0x39>;
- };
-
- tmp275: tmp275@48 {
- compatible = "ti,tmp275";
- reg = <0x48>;
- };
- };
-
- elm: elm@48080000 {
- status = "okay";
- };
-
- epwmss0: epwmss@48300000 {
- status = "okay";
-
- ecap0: ecap@48300100 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&ecap0_pins>;
- };
- };
-
- gpmc: gpmc@50000000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&nandflash_pins_s0>;
- ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */
- nand@0,0 {
- reg = <0 0 0>; /* CS0, offset 0 */
- nand-bus-width = <8>;
- ti,nand-ecc-opt = "bch8";
- gpmc,device-nand = "true";
- gpmc,device-width = <1>;
- gpmc,sync-clk-ps = <0>;
- gpmc,cs-on-ns = <0>;
- gpmc,cs-rd-off-ns = <44>;
- gpmc,cs-wr-off-ns = <44>;
- gpmc,adv-on-ns = <6>;
- gpmc,adv-rd-off-ns = <34>;
- gpmc,adv-wr-off-ns = <44>;
- gpmc,we-on-ns = <0>;
- gpmc,we-off-ns = <40>;
- gpmc,oe-on-ns = <0>;
- gpmc,oe-off-ns = <54>;
- gpmc,access-ns = <64>;
- gpmc,rd-cycle-ns = <82>;
- gpmc,wr-cycle-ns = <82>;
- gpmc,wait-on-read = "true";
- gpmc,wait-on-write = "true";
- gpmc,bus-turnaround-ns = <0>;
- gpmc,cycle2cycle-delay-ns = <0>;
- gpmc,clk-activation-ns = <0>;
- gpmc,wait-monitoring-ns = <0>;
- gpmc,wr-access-ns = <40>;
- gpmc,wr-data-mux-bus-ns = <0>;
-
- #address-cells = <1>;
- #size-cells = <1>;
- elm_id = <&elm>;
-
- /* MTD partition table */
- partition@0 {
- label = "SPL1";
- reg = <0x00000000 0x000020000>;
- };
-
- partition@1 {
- label = "SPL2";
- reg = <0x00020000 0x00020000>;
- };
-
- partition@2 {
- label = "SPL3";
- reg = <0x00040000 0x00020000>;
- };
-
- partition@3 {
- label = "SPL4";
- reg = <0x00060000 0x00020000>;
- };
-
- partition@4 {
- label = "U-boot";
- reg = <0x00080000 0x001e0000>;
- };
-
- partition@5 {
- label = "environment";
- reg = <0x00260000 0x00020000>;
- };
-
- partition@6 {
- label = "Kernel";
- reg = <0x00280000 0x00500000>;
- };
-
- partition@7 {
- label = "File-System";
- reg = <0x00780000 0x0F880000>;
- };
- };
- };
- };
-
vbat: fixedregulator@0 {
compatible = "regulator-fixed";
regulator-name = "vbat";
@@ -403,10 +85,447 @@
brightness-levels = <0 51 53 56 62 75 101 152 255>;
default-brightness-level = <8>;
};
+
+ panel {
+ compatible = "ti,tilcdc,panel";
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_pins_s0>;
+ panel-info {
+ ac-bias = <255>;
+ ac-bias-intrpt = <0>;
+ dma-burst-sz = <16>;
+ bpp = <32>;
+ fdd = <0x80>;
+ sync-edge = <0>;
+ sync-ctrl = <1>;
+ raster-order = <0>;
+ fifo-th = <0>;
+ };
+
+ display-timings {
+ 800x480p62 {
+ clock-frequency = <30000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hfront-porch = <39>;
+ hback-porch = <39>;
+ hsync-len = <47>;
+ vback-porch = <29>;
+ vfront-porch = <13>;
+ vsync-len = <2>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ };
+ };
+ };
+
+ sound {
+ compatible = "ti,da830-evm-audio";
+ ti,model = "AM335x-EVM";
+ ti,audio-codec = <&tlv320aic3106>;
+ ti,mcasp-controller = <&mcasp1>;
+ ti,codec-clock-rate = <12000000>;
+ ti,audio-routing =
+ "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT",
+ "LINE1L", "Line In",
+ "LINE1R", "Line In";
+ };
+};
+
+&am33xx_pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&matrix_keypad_s0 &volume_keys_s0 &clkout2_pin>;
+
+ matrix_keypad_s0: matrix_keypad_s0 {
+ pinctrl-single,pins = <
+ 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */
+ 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a6.gpio1_22 */
+ 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a9.gpio1_25 */
+ 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a10.gpio1_26 */
+ 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.gpio1_27 */
+ >;
+ };
+
+ volume_keys_s0: volume_keys_s0 {
+ pinctrl-single,pins = <
+ 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_sclk.gpio0_2 */
+ 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_d0.gpio0_3 */
+ >;
+ };
+
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+
+ i2c1_pins: pinmux_i2c1_pins {
+ pinctrl-single,pins = <
+ 0x158 (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_d1.i2c1_sda */
+ 0x15c (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_cs0.i2c1_scl */
+ >;
+ };
+
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+
+ clkout2_pin: pinmux_clkout2_pin {
+ pinctrl-single,pins = <
+ 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
+ >;
+ };
+
+ nandflash_pins_s0: nandflash_pins_s0 {
+ pinctrl-single,pins = <
+ 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */
+ 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */
+ 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */
+ 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */
+ 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */
+ 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */
+ 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */
+ 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */
+ 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */
+ 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */
+ 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */
+ 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */
+ 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */
+ 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */
+ 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */
+ >;
+ };
+
+ ecap0_pins: backlight_pins {
+ pinctrl-single,pins = <
+ 0x164 0x0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
+ >;
+ };
+
+ cpsw_default: cpsw_default {
+ pinctrl-single,pins = <
+ /* Slave 1 */
+ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */
+ 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */
+ 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */
+ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */
+ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */
+ 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */
+ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */
+ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */
+ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */
+ >;
+ };
+
+ cpsw_sleep: cpsw_sleep {
+ pinctrl-single,pins = <
+ /* Slave 1 reset value */
+ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ davinci_mdio_default: davinci_mdio_default {
+ pinctrl-single,pins = <
+ /* MDIO */
+ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
+
+ davinci_mdio_sleep: davinci_mdio_sleep {
+ pinctrl-single,pins = <
+ /* MDIO reset value */
+ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ lcd_pins_s0: lcd_pins_s0 {
+ pinctrl-single,pins = <
+ 0x20 0x01 /* gpmc_ad8.lcd_data16, OUTPUT | MODE1 */
+ 0x24 0x01 /* gpmc_ad9.lcd_data17, OUTPUT | MODE1 */
+ 0x28 0x01 /* gpmc_ad10.lcd_data18, OUTPUT | MODE1 */
+ 0x2c 0x01 /* gpmc_ad11.lcd_data19, OUTPUT | MODE1 */
+ 0x30 0x01 /* gpmc_ad12.lcd_data20, OUTPUT | MODE1 */
+ 0x34 0x01 /* gpmc_ad13.lcd_data21, OUTPUT | MODE1 */
+ 0x38 0x01 /* gpmc_ad14.lcd_data22, OUTPUT | MODE1 */
+ 0x3c 0x01 /* gpmc_ad15.lcd_data23, OUTPUT | MODE1 */
+ 0xa0 0x00 /* lcd_data0.lcd_data0, OUTPUT | MODE0 */
+ 0xa4 0x00 /* lcd_data1.lcd_data1, OUTPUT | MODE0 */
+ 0xa8 0x00 /* lcd_data2.lcd_data2, OUTPUT | MODE0 */
+ 0xac 0x00 /* lcd_data3.lcd_data3, OUTPUT | MODE0 */
+ 0xb0 0x00 /* lcd_data4.lcd_data4, OUTPUT | MODE0 */
+ 0xb4 0x00 /* lcd_data5.lcd_data5, OUTPUT | MODE0 */
+ 0xb8 0x00 /* lcd_data6.lcd_data6, OUTPUT | MODE0 */
+ 0xbc 0x00 /* lcd_data7.lcd_data7, OUTPUT | MODE0 */
+ 0xc0 0x00 /* lcd_data8.lcd_data8, OUTPUT | MODE0 */
+ 0xc4 0x00 /* lcd_data9.lcd_data9, OUTPUT | MODE0 */
+ 0xc8 0x00 /* lcd_data10.lcd_data10, OUTPUT | MODE0 */
+ 0xcc 0x00 /* lcd_data11.lcd_data11, OUTPUT | MODE0 */
+ 0xd0 0x00 /* lcd_data12.lcd_data12, OUTPUT | MODE0 */
+ 0xd4 0x00 /* lcd_data13.lcd_data13, OUTPUT | MODE0 */
+ 0xd8 0x00 /* lcd_data14.lcd_data14, OUTPUT | MODE0 */
+ 0xdc 0x00 /* lcd_data15.lcd_data15, OUTPUT | MODE0 */
+ 0xe0 0x00 /* lcd_vsync.lcd_vsync, OUTPUT | MODE0 */
+ 0xe4 0x00 /* lcd_hsync.lcd_hsync, OUTPUT | MODE0 */
+ 0xe8 0x00 /* lcd_pclk.lcd_pclk, OUTPUT | MODE0 */
+ 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OUTPUT | MODE0 */
+ >;
+ };
+
+ am335x_evm_audio_pins: am335x_evm_audio_pins {
+ pinctrl-single,pins = <
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rx_dv.mcasp1_aclkx */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_txd3.mcasp1_fsx */
+ 0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
+ >;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps: tps@2d {
+ reg = <0x2d>;
+ };
+};
+
+&usb {
+ status = "okay";
+
+ control@44e10000 {
+ status = "okay";
+ };
+
+ usb-phy@47401300 {
+ status = "okay";
+ };
+
+ usb-phy@47401b00 {
+ status = "okay";
+ };
+
+ usb@47401000 {
+ status = "okay";
+ };
+
+ usb@47401800 {
+ status = "okay";
+ dr_mode = "host";
+ };
+
+ dma-controller@07402000 {
+ status = "okay";
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
+ status = "okay";
+ clock-frequency = <100000>;
+
+ lis331dlh: lis331dlh@18 {
+ compatible = "st,lis331dlh", "st,lis3lv02d";
+ reg = <0x18>;
+ Vdd-supply = <&lis3_reg>;
+ Vdd_IO-supply = <&lis3_reg>;
+
+ st,click-single-x;
+ st,click-single-y;
+ st,click-single-z;
+ st,click-thresh-x = <10>;
+ st,click-thresh-y = <10>;
+ st,click-thresh-z = <10>;
+ st,irq1-click;
+ st,irq2-click;
+ st,wakeup-x-lo;
+ st,wakeup-x-hi;
+ st,wakeup-y-lo;
+ st,wakeup-y-hi;
+ st,wakeup-z-lo;
+ st,wakeup-z-hi;
+ st,min-limit-x = <120>;
+ st,min-limit-y = <120>;
+ st,min-limit-z = <140>;
+ st,max-limit-x = <550>;
+ st,max-limit-y = <550>;
+ st,max-limit-z = <750>;
+ };
+
+ tsl2550: tsl2550@39 {
+ compatible = "taos,tsl2550";
+ reg = <0x39>;
+ };
+
+ tmp275: tmp275@48 {
+ compatible = "ti,tmp275";
+ reg = <0x48>;
+ };
+
+ tlv320aic3106: tlv320aic3106@1b {
+ compatible = "ti,tlv320aic3106";
+ reg = <0x1b>;
+ status = "okay";
+
+ /* Regulators */
+ AVDD-supply = <&vaux2_reg>;
+ IOVDD-supply = <&vaux2_reg>;
+ DRVDD-supply = <&vaux2_reg>;
+ DVDD-supply = <&vbat>;
+ };
+};
+
+&lcdc {
+ status = "okay";
+};
+
+&elm {
+ status = "okay";
+};
+
+&epwmss0 {
+ status = "okay";
+
+ ecap0: ecap@48300100 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ecap0_pins>;
+ };
+};
+
+&gpmc {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&nandflash_pins_s0>;
+ ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */
+ nand@0,0 {
+ reg = <0 0 0>; /* CS0, offset 0 */
+ nand-bus-width = <8>;
+ ti,nand-ecc-opt = "bch8";
+ gpmc,device-nand = "true";
+ gpmc,device-width = <1>;
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <44>;
+ gpmc,cs-wr-off-ns = <44>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <34>;
+ gpmc,adv-wr-off-ns = <44>;
+ gpmc,we-on-ns = <0>;
+ gpmc,we-off-ns = <40>;
+ gpmc,oe-on-ns = <0>;
+ gpmc,oe-off-ns = <54>;
+ gpmc,access-ns = <64>;
+ gpmc,rd-cycle-ns = <82>;
+ gpmc,wr-cycle-ns = <82>;
+ gpmc,wait-on-read = "true";
+ gpmc,wait-on-write = "true";
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <0>;
+ gpmc,clk-activation-ns = <0>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ elm_id = <&elm>;
+
+ /* MTD partition table */
+ partition@0 {
+ label = "SPL1";
+ reg = <0x00000000 0x000020000>;
+ };
+
+ partition@1 {
+ label = "SPL2";
+ reg = <0x00020000 0x00020000>;
+ };
+
+ partition@2 {
+ label = "SPL3";
+ reg = <0x00040000 0x00020000>;
+ };
+
+ partition@3 {
+ label = "SPL4";
+ reg = <0x00060000 0x00020000>;
+ };
+
+ partition@4 {
+ label = "U-boot";
+ reg = <0x00080000 0x001e0000>;
+ };
+
+ partition@5 {
+ label = "environment";
+ reg = <0x00260000 0x00020000>;
+ };
+
+ partition@6 {
+ label = "Kernel";
+ reg = <0x00280000 0x00500000>;
+ };
+
+ partition@7 {
+ label = "File-System";
+ reg = <0x00780000 0x0F880000>;
+ };
+ };
};
#include "tps65910.dtsi"
+&mcasp1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&am335x_evm_audio_pins>;
+
+ status = "okay";
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+ /* 4 serializers */
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 0 0 1 2
+ >;
+ tx-num-evt = <1>;
+ rx-num-evt = <1>;
+};
+
&tps {
vcc1-supply = <&vbat>;
vcc2-supply = <&vbat>;
@@ -477,6 +596,8 @@
};
vmmc_reg: regulator@12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
regulator-always-on;
};
};
@@ -517,3 +638,17 @@
ti,adc-channels = <4 5 6 7>;
};
};
+
+&mmc1 {
+ status = "okay";
+ vmmc-supply = <&vmmc_reg>;
+ bus-width = <4>;
+};
+
+&sham {
+ status = "okay";
+};
+
+&aes {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts
index 4f339fa..03febf8 100644
--- a/arch/arm/boot/dts/am335x-evmsk.dts
+++ b/arch/arm/boot/dts/am335x-evmsk.dts
@@ -31,210 +31,6 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- am33xx_pinmux: pinmux@44e10800 {
- pinctrl-names = "default";
- pinctrl-0 = <&gpio_keys_s0 &clkout2_pin>;
-
- user_leds_s0: user_leds_s0 {
- pinctrl-single,pins = <
- 0x10 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad4.gpio1_4 */
- 0x14 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad5.gpio1_5 */
- 0x18 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad6.gpio1_6 */
- 0x1c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad7.gpio1_7 */
- >;
- };
-
- gpio_keys_s0: gpio_keys_s0 {
- pinctrl-single,pins = <
- 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_oen_ren.gpio2_3 */
- 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_advn_ale.gpio2_2 */
- 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_wait0.gpio0_30 */
- 0x9c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ben0_cle.gpio2_5 */
- >;
- };
-
- i2c0_pins: pinmux_i2c0_pins {
- pinctrl-single,pins = <
- 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
- 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
- >;
- };
-
- uart0_pins: pinmux_uart0_pins {
- pinctrl-single,pins = <
- 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
- 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
- >;
- };
-
- clkout2_pin: pinmux_clkout2_pin {
- pinctrl-single,pins = <
- 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
- >;
- };
-
- ecap2_pins: backlight_pins {
- pinctrl-single,pins = <
- 0x19c 0x4 /* mcasp0_ahclkr.ecap2_in_pwm2_out MODE4 */
- >;
- };
-
- cpsw_default: cpsw_default {
- pinctrl-single,pins = <
- /* Slave 1 */
- 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */
- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */
- 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */
- 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */
- 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */
- 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */
- 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */
- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */
- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */
- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */
- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */
- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */
-
- /* Slave 2 */
- 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a0.rgmii2_tctl */
- 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a1.rgmii2_rctl */
- 0x48 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a2.rgmii2_td3 */
- 0x4c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a3.rgmii2_td2 */
- 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a4.rgmii2_td1 */
- 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a5.rgmii2_td0 */
- 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a6.rgmii2_tclk */
- 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a7.rgmii2_rclk */
- 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a8.rgmii2_rd3 */
- 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a9.rgmii2_rd2 */
- 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a10.rgmii2_rd1 */
- 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a11.rgmii2_rd0 */
- >;
- };
-
- cpsw_sleep: cpsw_sleep {
- pinctrl-single,pins = <
- /* Slave 1 reset value */
- 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
-
- /* Slave 2 reset value*/
- 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
-
- davinci_mdio_default: davinci_mdio_default {
- pinctrl-single,pins = <
- /* MDIO */
- 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
- 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
- >;
- };
-
- davinci_mdio_sleep: davinci_mdio_sleep {
- pinctrl-single,pins = <
- /* MDIO reset value */
- 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
- };
-
- ocp {
- uart0: serial@44e09000 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins>;
-
- status = "okay";
- };
-
- i2c0: i2c@44e0b000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
-
- status = "okay";
- clock-frequency = <400000>;
-
- tps: tps@2d {
- reg = <0x2d>;
- };
-
- lis331dlh: lis331dlh@18 {
- compatible = "st,lis331dlh", "st,lis3lv02d";
- reg = <0x18>;
- Vdd-supply = <&lis3_reg>;
- Vdd_IO-supply = <&lis3_reg>;
-
- st,click-single-x;
- st,click-single-y;
- st,click-single-z;
- st,click-thresh-x = <10>;
- st,click-thresh-y = <10>;
- st,click-thresh-z = <10>;
- st,irq1-click;
- st,irq2-click;
- st,wakeup-x-lo;
- st,wakeup-x-hi;
- st,wakeup-y-lo;
- st,wakeup-y-hi;
- st,wakeup-z-lo;
- st,wakeup-z-hi;
- st,min-limit-x = <120>;
- st,min-limit-y = <120>;
- st,min-limit-z = <140>;
- st,max-limit-x = <550>;
- st,max-limit-y = <550>;
- st,max-limit-z = <750>;
- };
- };
-
- musb: usb@47400000 {
- status = "okay";
-
- control@44e10000 {
- status = "okay";
- };
-
- usb-phy@47401300 {
- status = "okay";
- };
-
- usb@47401000 {
- status = "okay";
- };
- };
-
- epwmss2: epwmss@48304000 {
- status = "okay";
-
- ecap2: ecap@48304100 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&ecap2_pins>;
- };
- };
- };
-
vbat: fixedregulator@0 {
compatible = "regulator-fixed";
regulator-name = "vbat";
@@ -319,6 +115,240 @@
brightness-levels = <0 58 61 66 75 90 125 170 255>;
default-brightness-level = <8>;
};
+
+ sound {
+ compatible = "ti,da830-evm-audio";
+ ti,model = "AM335x-EVMSK";
+ ti,audio-codec = <&tlv320aic3106>;
+ ti,mcasp-controller = <&mcasp1>;
+ ti,codec-clock-rate = <24576000>;
+ ti,audio-routing =
+ "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT";
+ };
+};
+
+&am33xx_pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys_s0 &clkout2_pin>;
+
+ user_leds_s0: user_leds_s0 {
+ pinctrl-single,pins = <
+ 0x10 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad4.gpio1_4 */
+ 0x14 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad5.gpio1_5 */
+ 0x18 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad6.gpio1_6 */
+ 0x1c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad7.gpio1_7 */
+ >;
+ };
+
+ gpio_keys_s0: gpio_keys_s0 {
+ pinctrl-single,pins = <
+ 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_oen_ren.gpio2_3 */
+ 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_advn_ale.gpio2_2 */
+ 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_wait0.gpio0_30 */
+ 0x9c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ben0_cle.gpio2_5 */
+ >;
+ };
+
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+
+ clkout2_pin: pinmux_clkout2_pin {
+ pinctrl-single,pins = <
+ 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
+ >;
+ };
+
+ ecap2_pins: backlight_pins {
+ pinctrl-single,pins = <
+ 0x19c 0x4 /* mcasp0_ahclkr.ecap2_in_pwm2_out MODE4 */
+ >;
+ };
+
+ cpsw_default: cpsw_default {
+ pinctrl-single,pins = <
+ /* Slave 1 */
+ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */
+ 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */
+ 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */
+ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */
+ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */
+ 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */
+ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */
+ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */
+ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */
+
+ /* Slave 2 */
+ 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a0.rgmii2_tctl */
+ 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a1.rgmii2_rctl */
+ 0x48 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a2.rgmii2_td3 */
+ 0x4c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a3.rgmii2_td2 */
+ 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a4.rgmii2_td1 */
+ 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a5.rgmii2_td0 */
+ 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a6.rgmii2_tclk */
+ 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a7.rgmii2_rclk */
+ 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a8.rgmii2_rd3 */
+ 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a9.rgmii2_rd2 */
+ 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a10.rgmii2_rd1 */
+ 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a11.rgmii2_rd0 */
+ >;
+ };
+
+ cpsw_sleep: cpsw_sleep {
+ pinctrl-single,pins = <
+ /* Slave 1 reset value */
+ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+
+ /* Slave 2 reset value*/
+ 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ davinci_mdio_default: davinci_mdio_default {
+ pinctrl-single,pins = <
+ /* MDIO */
+ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
+
+ davinci_mdio_sleep: davinci_mdio_sleep {
+ pinctrl-single,pins = <
+ /* MDIO reset value */
+ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ mcasp1_pins: mcasp1_pins {
+ pinctrl-single,pins = <
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */
+ 0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
+ >;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps: tps@2d {
+ reg = <0x2d>;
+ };
+
+ lis331dlh: lis331dlh@18 {
+ compatible = "st,lis331dlh", "st,lis3lv02d";
+ reg = <0x18>;
+ Vdd-supply = <&lis3_reg>;
+ Vdd_IO-supply = <&lis3_reg>;
+
+ st,click-single-x;
+ st,click-single-y;
+ st,click-single-z;
+ st,click-thresh-x = <10>;
+ st,click-thresh-y = <10>;
+ st,click-thresh-z = <10>;
+ st,irq1-click;
+ st,irq2-click;
+ st,wakeup-x-lo;
+ st,wakeup-x-hi;
+ st,wakeup-y-lo;
+ st,wakeup-y-hi;
+ st,wakeup-z-lo;
+ st,wakeup-z-hi;
+ st,min-limit-x = <120>;
+ st,min-limit-y = <120>;
+ st,min-limit-z = <140>;
+ st,max-limit-x = <550>;
+ st,max-limit-y = <550>;
+ st,max-limit-z = <750>;
+ };
+
+ tlv320aic3106: tlv320aic3106@1b {
+ compatible = "ti,tlv320aic3106";
+ reg = <0x1b>;
+ status = "okay";
+
+ /* Regulators */
+ AVDD-supply = <&vaux2_reg>;
+ IOVDD-supply = <&vaux2_reg>;
+ DRVDD-supply = <&vaux2_reg>;
+ DVDD-supply = <&vbat>;
+ };
+};
+
+&usb {
+ status = "okay";
+
+ control@44e10000 {
+ status = "okay";
+ };
+
+ usb-phy@47401300 {
+ status = "okay";
+ };
+
+ usb@47401000 {
+ status = "okay";
+ };
+};
+
+&epwmss2 {
+ status = "okay";
+
+ ecap2: ecap@48304100 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ecap2_pins>;
+ };
};
#include "tps65910.dtsi"
@@ -393,6 +423,8 @@
};
vmmc_reg: regulator@12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
regulator-always-on;
};
};
@@ -419,3 +451,37 @@
phy_id = <&davinci_mdio>, <1>;
phy-mode = "rgmii-txid";
};
+
+&mmc1 {
+ status = "okay";
+ vmmc-supply = <&vmmc_reg>;
+ bus-width = <4>;
+};
+
+&sham {
+ status = "okay";
+};
+
+&aes {
+ status = "okay";
+};
+
+&gpio0 {
+ ti,no-reset-on-init;
+};
+
+&mcasp1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcasp1_pins>;
+
+ status = "okay";
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+ /* 4 serializers */
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 0 0 1 2
+ >;
+ tx-num-evt = <1>;
+ rx-num-evt = <1>;
+};
diff --git a/arch/arm/boot/dts/am335x-igep0033.dtsi b/arch/arm/boot/dts/am335x-igep0033.dtsi
new file mode 100644
index 0000000..6196244
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-igep0033.dtsi
@@ -0,0 +1,278 @@
+/*
+ * am335x-igep0033.dtsi - Device Tree file for IGEP COM AQUILA AM335x
+ *
+ * Copyright (C) 2013 ISEE 2007 SL - http://www.isee.biz
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&vdd1_reg>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ leds {
+ pinctrl-names = "default";
+ pinctrl-0 = <&leds_pins>;
+
+ compatible = "gpio-leds";
+
+ led@0 {
+ label = "com:green:user";
+ gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ vbat: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vbat";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ };
+
+ vmmc: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vmmc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&am33xx_pinmux {
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+
+ nandflash_pins: pinmux_nandflash_pins {
+ pinctrl-single,pins = <
+ 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */
+ 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */
+ 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */
+ 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */
+ 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */
+ 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */
+ 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */
+ 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */
+ 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */
+ 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */
+ 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */
+ 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */
+ 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */
+ 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */
+ 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */
+ >;
+ };
+
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+
+ leds_pins: pinmux_leds_pins {
+ pinctrl-single,pins = <
+ 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */
+ >;
+ };
+};
+
+&cpsw_emac0 {
+ phy_id = <&davinci_mdio>, <0>;
+};
+
+&cpsw_emac1 {
+ phy_id = <&davinci_mdio>, <1>;
+};
+
+&elm {
+ status = "okay";
+};
+
+&gpmc {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&nandflash_pins>;
+
+ ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */
+
+ nand@0,0 {
+ reg = <0 0 0>; /* CS0, offset 0 */
+ nand-bus-width = <8>;
+ ti,nand-ecc-opt = "bch8";
+ gpmc,device-nand = "true";
+ gpmc,device-width = <1>;
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <44>;
+ gpmc,cs-wr-off-ns = <44>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <34>;
+ gpmc,adv-wr-off-ns = <44>;
+ gpmc,we-on-ns = <0>;
+ gpmc,we-off-ns = <40>;
+ gpmc,oe-on-ns = <0>;
+ gpmc,oe-off-ns = <54>;
+ gpmc,access-ns = <64>;
+ gpmc,rd-cycle-ns = <82>;
+ gpmc,wr-cycle-ns = <82>;
+ gpmc,wait-on-read = "true";
+ gpmc,wait-on-write = "true";
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <0>;
+ gpmc,clk-activation-ns = <0>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ elm_id = <&elm>;
+
+ /* MTD partition table */
+ partition@0 {
+ label = "SPL";
+ reg = <0x00000000 0x000080000>;
+ };
+
+ partition@1 {
+ label = "U-boot";
+ reg = <0x00080000 0x001e0000>;
+ };
+
+ partition@2 {
+ label = "U-Boot Env";
+ reg = <0x00260000 0x00020000>;
+ };
+
+ partition@3 {
+ label = "Kernel";
+ reg = <0x00280000 0x00500000>;
+ };
+
+ partition@4 {
+ label = "File System";
+ reg = <0x00780000 0x007880000>;
+ };
+ };
+};
+
+&i2c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ clock-frequency = <400000>;
+
+ tps: tps@2d {
+ reg = <0x2d>;
+ };
+};
+
+&mmc1 {
+ status = "okay";
+ vmmc-supply = <&vmmc>;
+ bus-width = <4>;
+};
+
+&uart0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+};
+
+#include "tps65910.dtsi"
+
+&tps {
+ vcc1-supply = <&vbat>;
+ vcc2-supply = <&vbat>;
+ vcc3-supply = <&vbat>;
+ vcc4-supply = <&vbat>;
+ vcc5-supply = <&vbat>;
+ vcc6-supply = <&vbat>;
+ vcc7-supply = <&vbat>;
+ vccio-supply = <&vbat>;
+
+ regulators {
+ vrtc_reg: regulator@0 {
+ regulator-always-on;
+ };
+
+ vio_reg: regulator@1 {
+ regulator-always-on;
+ };
+
+ vdd1_reg: regulator@2 {
+ /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
+ regulator-name = "vdd_mpu";
+ regulator-min-microvolt = <912500>;
+ regulator-max-microvolt = <1312500>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd2_reg: regulator@3 {
+ /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
+ regulator-name = "vdd_core";
+ regulator-min-microvolt = <912500>;
+ regulator-max-microvolt = <1150000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd3_reg: regulator@4 {
+ regulator-always-on;
+ };
+
+ vdig1_reg: regulator@5 {
+ regulator-always-on;
+ };
+
+ vdig2_reg: regulator@6 {
+ regulator-always-on;
+ };
+
+ vpll_reg: regulator@7 {
+ regulator-always-on;
+ };
+
+ vdac_reg: regulator@8 {
+ regulator-always-on;
+ };
+
+ vaux1_reg: regulator@9 {
+ regulator-always-on;
+ };
+
+ vaux2_reg: regulator@10 {
+ regulator-always-on;
+ };
+
+ vaux33_reg: regulator@11 {
+ regulator-always-on;
+ };
+
+ vmmc_reg: regulator@12 {
+ regulator-always-on;
+ };
+ };
+};
+
diff --git a/arch/arm/boot/dts/am335x-nano.dts b/arch/arm/boot/dts/am335x-nano.dts
new file mode 100644
index 0000000..9907b49
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-nano.dts
@@ -0,0 +1,431 @@
+/*
+ * Copyright (C) 2013 Newflow Ltd - http://www.newflow.co.uk/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+ model = "Newflow AM335x NanoBone";
+ compatible = "ti,am33xx";
+
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&dcdc2_reg>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led@0 {
+ label = "nanobone:green:usr1";
+ gpios = <&gpio1 5 0>;
+ default-state = "off";
+ };
+ };
+};
+
+&am33xx_pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&misc_pins>;
+
+ misc_pins: misc_pins {
+ pinctrl-single,pins = <
+ 0x15c (PIN_OUTPUT | MUX_MODE7) /* spi0_cs0.gpio0_5 */
+ >;
+ };
+
+ gpmc_pins: gpmc_pins {
+ pinctrl-single,pins = <
+ 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */
+ 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */
+ 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */
+ 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */
+ 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */
+ 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */
+ 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */
+ 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */
+ 0x20 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad8.gpmc_ad8 */
+ 0x24 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad9.gpmc_ad9 */
+ 0x28 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad10.gpmc_ad10 */
+ 0x2c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad11.gpmc_ad11 */
+ 0x30 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad12.gpmc_ad12 */
+ 0x34 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad13.gpmc_ad13 */
+ 0x38 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad14.gpmc_ad14 */
+ 0x3c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad15.gpmc_ad15 */
+
+ 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */
+ 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */
+ 0x80 (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn1.gpmc_csn1 */
+ 0x84 (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn2.gpmc_csn2 */
+ 0x88 (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn3.gpmc_csn3 */
+
+ 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */
+ 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */
+ 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */
+ 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0_cle.gpmc_ben0_cle */
+
+ 0xa4 (PIN_OUTPUT | MUX_MODE1) /* lcd_data1.gpmc_a1 */
+ 0xa8 (PIN_OUTPUT | MUX_MODE1) /* lcd_data2.gpmc_a2 */
+ 0xac (PIN_OUTPUT | MUX_MODE1) /* lcd_data3.gpmc_a3 */
+ 0xb0 (PIN_OUTPUT | MUX_MODE1) /* lcd_data4.gpmc_a4 */
+ 0xb4 (PIN_OUTPUT | MUX_MODE1) /* lcd_data5.gpmc_a5 */
+ 0xb8 (PIN_OUTPUT | MUX_MODE1) /* lcd_data6.gpmc_a6 */
+ 0xbc (PIN_OUTPUT | MUX_MODE1) /* lcd_data7.gpmc_a7 */
+
+ 0xe0 (PIN_OUTPUT | MUX_MODE1) /* lcd_vsync.gpmc_a8 */
+ 0xe4 (PIN_OUTPUT | MUX_MODE1) /* lcd_hsync.gpmc_a9 */
+ 0xe8 (PIN_OUTPUT | MUX_MODE1) /* lcd_pclk.gpmc_a10 */
+ >;
+ };
+
+ i2c0_pins: i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+
+ uart0_pins: uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+
+ uart1_pins: uart1_pins {
+ pinctrl-single,pins = <
+ 0x178 (PIN_OUTPUT | MUX_MODE7) /* uart1_ctsn.uart1_ctsn */
+ 0x17c (PIN_OUTPUT | MUX_MODE7) /* uart1_rtsn.uart1_rtsn */
+ 0x180 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */
+ 0x184 (PIN_OUTPUT | MUX_MODE0) /* uart1_txd.uart1_txd */
+ >;
+ };
+
+ uart2_pins: uart2_pins {
+ pinctrl-single,pins = <
+ 0xc0 (PIN_INPUT_PULLUP | MUX_MODE7) /* lcd_data8.gpio2[14] */
+ 0xc4 (PIN_OUTPUT | MUX_MODE7) /* lcd_data9.gpio2[15] */
+ 0x150 (PIN_INPUT | MUX_MODE1) /* spi0_sclk.uart2_rxd */
+ 0x154 (PIN_OUTPUT | MUX_MODE1) /* spi0_d0.uart2_txd */
+ >;
+ };
+
+ uart3_pins: uart3_pins {
+ pinctrl-single,pins = <
+ 0xc8 (PIN_INPUT_PULLUP | MUX_MODE6) /* lcd_data10.uart3_ctsn */
+ 0xcc (PIN_OUTPUT | MUX_MODE6) /* lcd_data11.uart3_rtsn */
+ 0x160 (PIN_INPUT | MUX_MODE1) /* spi0_cs1.uart3_rxd */
+ 0x164 (PIN_OUTPUT | MUX_MODE1) /* ecap0_in_pwm0_out.uart3_txd */
+ >;
+ };
+
+ uart4_pins: uart4_pins {
+ pinctrl-single,pins = <
+ 0xd0 (PIN_INPUT_PULLUP | MUX_MODE6) /* lcd_data12.uart4_ctsn */
+ 0xd4 (PIN_OUTPUT | MUX_MODE6) /* lcd_data13.uart4_rtsn */
+ 0x168 (PIN_INPUT | MUX_MODE1) /* uart0_ctsn.uart4_rxd */
+ 0x16c (PIN_OUTPUT | MUX_MODE1) /* uart0_rtsn.uart4_txd */
+ >;
+ };
+
+ uart5_pins: uart5_pins {
+ pinctrl-single,pins = <
+ 0xd8 (PIN_INPUT | MUX_MODE4) /* lcd_data14.uart5_rxd */
+ 0x144 (PIN_OUTPUT | MUX_MODE3) /* rmiii1_refclk.uart5_txd */
+ >;
+ };
+
+ mmc1_pins: mmc1_pins {
+ pinctrl-single,pins = <
+ 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */
+ 0xf4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */
+ 0xf8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */
+ 0xfc (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */
+ 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */
+ 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */
+ 0x1e8 (PIN_INPUT_PULLUP | MUX_MODE7) /* emu1.gpio3[8] */
+ 0x1a0 (PIN_INPUT_PULLUP | MUX_MODE7) /* mcasp0_aclkr.gpio3[18] */
+ >;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "okay";
+ rts-gpio = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+ rs485-rts-active-high;
+ rs485-rx-during-tx;
+ rs485-rts-delay = <1 1>;
+ linux,rs485-enabled-at-boot-time;
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+ rts-gpio = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+ rs485-rts-active-high;
+ rs485-rts-delay = <1 1>;
+ linux,rs485-enabled-at-boot-time;
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart5_pins>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ gpio@20 {
+ compatible = "mcp,mcp23017";
+ reg = <0x20>;
+ };
+
+ tps: tps@24 {
+ reg = <0x24>;
+ };
+
+ eeprom@53 {
+ compatible = "mcp,24c02";
+ reg = <0x53>;
+ pagesize = <8>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1307";
+ reg = <0x68>;
+ };
+};
+
+&elm {
+ status = "okay";
+};
+
+&gpmc {
+ compatible = "ti,am3352-gpmc";
+ ti,hwmods = "gpmc";
+ status = "okay";
+ gpmc,num-waitpins = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmc_pins>;
+
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x08000000 0x08000000>; /* CS0: NOR 128M */
+
+ nor@0,0 {
+ reg = <0 0x00000000 0x08000000>;
+ compatible = "cfi-flash";
+ linux,mtd-name = "spansion,s29gl010p11t";
+ bank-width = <2>;
+
+ gpmc,mux-add-data = <2>;
+
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <160>;
+ gpmc,cs-wr-off-ns = <160>;
+ gpmc,adv-on-ns = <10>;
+ gpmc,adv-rd-off-ns = <30>;
+ gpmc,adv-wr-off-ns = <30>;
+ gpmc,oe-on-ns = <40>;
+ gpmc,oe-off-ns = <160>;
+ gpmc,we-on-ns = <40>;
+ gpmc,we-off-ns = <160>;
+ gpmc,rd-cycle-ns = <160>;
+ gpmc,wr-cycle-ns = <160>;
+ gpmc,access-ns = <150>;
+ gpmc,page-burst-access-ns = <10>;
+ gpmc,cycle2cycle-samecsen;
+ gpmc,cycle2cycle-delay-ns = <20>;
+ gpmc,wr-data-mux-bus-ns = <70>;
+ gpmc,wr-access-ns = <80>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /*
+ MTD partition table
+ ===================
+ +------------+-->0x00000000-> U-Boot start
+ | |
+ | |-->0x000BFFFF-> U-Boot end
+ | |-->0x000C0000-> ENV1 start
+ | |
+ | |-->0x000DFFFF-> ENV1 end
+ | |-->0x000E0000-> ENV2 start
+ | |
+ | |-->0x000FFFFF-> ENV2 end
+ | |-->0x00100000-> Kernel start
+ | |
+ | |-->0x004FFFFF-> Kernel end
+ | |-->0x00500000-> File system start
+ | |
+ | |-->0x014FFFFF-> File system end
+ | |-->0x01500000-> User data start
+ | |
+ | |-->0x03FFFFFF-> User data end
+ | |-->0x04000000-> Data storage start
+ | |
+ +------------+-->0x08000000-> NOR end (Free end)
+ */
+ partition@0 {
+ label = "boot";
+ reg = <0x00000000 0x000c0000>; /* 768KB */
+ };
+
+ partition@1 {
+ label = "env1";
+ reg = <0x000c0000 0x00020000>; /* 128KB */
+ };
+
+ partition@2 {
+ label = "env2";
+ reg = <0x000e0000 0x00020000>; /* 128KB */
+ };
+
+ partition@3 {
+ label = "kernel";
+ reg = <0x00100000 0x00400000>; /* 4MB */
+ };
+
+ partition@4 {
+ label = "rootfs";
+ reg = <0x00500000 0x01000000>; /* 16MB */
+ };
+
+ partition@5 {
+ label = "user";
+ reg = <0x01500000 0x02b00000>; /* 43MB */
+ };
+
+ partition@6 {
+ label = "data";
+ reg = <0x04000000 0x04000000>; /* 64MB */
+ };
+ };
+};
+
+&mac {
+ dual_emac = <1>;
+};
+
+&cpsw_emac0 {
+ phy_id = <&davinci_mdio>, <0>;
+ dual_emac_res_vlan = <1>;
+};
+
+&cpsw_emac1 {
+ phy_id = <&davinci_mdio>, <1>;
+ dual_emac_res_vlan = <2>;
+};
+
+&mmc1 {
+ status = "okay";
+ vmmc-supply = <&ldo4_reg>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ bus-width = <4>;
+ cd-gpios = <&gpio3 8 0>;
+ wp-gpios = <&gpio3 18 0>;
+};
+
+#include "tps65217.dtsi"
+
+&tps {
+ regulators {
+ dcdc1_reg: regulator@0 {
+ /* +1.5V voltage with ±4% tolerance */
+ regulator-min-microvolt = <1450000>;
+ regulator-max-microvolt = <1550000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ dcdc2_reg: regulator@1 {
+ /* VDD_MPU voltage limits 0.95V - 1.1V with ±4% tolerance */
+ regulator-name = "vdd_mpu";
+ regulator-min-microvolt = <915000>;
+ regulator-max-microvolt = <1140000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ dcdc3_reg: regulator@2 {
+ /* VDD_CORE voltage limits 0.95V - 1.1V with ±4% tolerance */
+ regulator-name = "vdd_core";
+ regulator-min-microvolt = <915000>;
+ regulator-max-microvolt = <1140000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1_reg: regulator@3 {
+ /* +1.8V voltage with ±4% tolerance */
+ regulator-min-microvolt = <1750000>;
+ regulator-max-microvolt = <1870000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2_reg: regulator@4 {
+ /* +3.3V voltage with ±4% tolerance */
+ regulator-min-microvolt = <3175000>;
+ regulator-max-microvolt = <3430000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_reg: regulator@5 {
+ /* +1.8V voltage with ±4% tolerance */
+ regulator-min-microvolt = <1750000>;
+ regulator-max-microvolt = <1870000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4_reg: regulator@6 {
+ /* +3.3V voltage with ±4% tolerance */
+ regulator-min-microvolt = <3175000>;
+ regulator-max-microvolt = <3430000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index f9c5da9..0ca13ad 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -18,6 +18,9 @@
interrupt-parent = <&intc>;
aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
serial0 = &uart0;
serial1 = &uart1;
serial2 = &uart2;
@@ -30,6 +33,8 @@
usb1 = &usb1;
phy0 = &usb0_phy;
phy1 = &usb1_phy;
+ ethernet0 = &cpsw_emac0;
+ ethernet1 = &cpsw_emac1;
};
cpus {
@@ -57,6 +62,11 @@
};
};
+ pmu {
+ compatible = "arm,cortex-a8-pmu";
+ interrupts = <3>;
+ };
+
/*
* The soc node represents the soc top level view. It is uses for IPs
* that are not memory mapped in the MPU view or for the MPU itself.
@@ -100,13 +110,25 @@
reg = <0x48200000 0x1000>;
};
+ edma: edma@49000000 {
+ compatible = "ti,edma3";
+ ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
+ reg = <0x49000000 0x10000>,
+ <0x44e10f90 0x10>;
+ interrupts = <12 13 14>;
+ #dma-cells = <1>;
+ dma-channels = <64>;
+ ti,edma-regions = <4>;
+ ti,edma-slots = <256>;
+ };
+
gpio0: gpio@44e07000 {
compatible = "ti,omap4-gpio";
ti,hwmods = "gpio1";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
reg = <0x44e07000 0x1000>;
interrupts = <96>;
};
@@ -117,7 +139,7 @@
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
reg = <0x4804c000 0x1000>;
interrupts = <98>;
};
@@ -128,7 +150,7 @@
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
reg = <0x481ac000 0x1000>;
interrupts = <32>;
};
@@ -139,7 +161,7 @@
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
reg = <0x481ae000 0x1000>;
interrupts = <62>;
};
@@ -228,6 +250,44 @@
status = "disabled";
};
+ mmc1: mmc@48060000 {
+ compatible = "ti,omap4-hsmmc";
+ ti,hwmods = "mmc1";
+ ti,dual-volt;
+ ti,needs-special-reset;
+ ti,needs-special-hs-handling;
+ dmas = <&edma 24
+ &edma 25>;
+ dma-names = "tx", "rx";
+ interrupts = <64>;
+ interrupt-parent = <&intc>;
+ reg = <0x48060000 0x1000>;
+ status = "disabled";
+ };
+
+ mmc2: mmc@481d8000 {
+ compatible = "ti,omap4-hsmmc";
+ ti,hwmods = "mmc2";
+ ti,needs-special-reset;
+ dmas = <&edma 2
+ &edma 3>;
+ dma-names = "tx", "rx";
+ interrupts = <28>;
+ interrupt-parent = <&intc>;
+ reg = <0x481d8000 0x1000>;
+ status = "disabled";
+ };
+
+ mmc3: mmc@47810000 {
+ compatible = "ti,omap4-hsmmc";
+ ti,hwmods = "mmc3";
+ ti,needs-special-reset;
+ interrupts = <29>;
+ interrupt-parent = <&intc>;
+ reg = <0x47810000 0x1000>;
+ status = "disabled";
+ };
+
wdt2: wdt@44e35000 {
compatible = "ti,omap3-wdt";
ti,hwmods = "wd_timer2";
@@ -323,6 +383,11 @@
interrupts = <65>;
ti,spi-num-cs = <2>;
ti,hwmods = "spi0";
+ dmas = <&edma 16
+ &edma 17
+ &edma 18
+ &edma 19>;
+ dma-names = "tx0", "rx0", "tx1", "rx1";
status = "disabled";
};
@@ -334,6 +399,11 @@
interrupts = <125>;
ti,spi-num-cs = <2>;
ti,hwmods = "spi1";
+ dmas = <&edma 42
+ &edma 43
+ &edma 44
+ &edma 45>;
+ dma-names = "tx0", "rx0", "tx1", "rx1";
status = "disabled";
};
@@ -346,7 +416,7 @@
ti,hwmods = "usb_otg_hs";
status = "disabled";
- ctrl_mod: control@44e10000 {
+ usb_ctrl_mod: control@44e10000 {
compatible = "ti,am335x-usb-ctrl-module";
reg = <0x44e10620 0x10
0x44e10648 0x4>;
@@ -359,7 +429,7 @@
reg = <0x47401300 0x100>;
reg-names = "phy";
status = "disabled";
- ti,ctrl_mod = <&ctrl_mod>;
+ ti,ctrl_mod = <&usb_ctrl_mod>;
};
usb0: usb@47401000 {
@@ -407,7 +477,7 @@
reg = <0x47401b00 0x100>;
reg-names = "phy";
status = "disabled";
- ti,ctrl_mod = <&ctrl_mod>;
+ ti,ctrl_mod = <&usb_ctrl_mod>;
};
usb1: usb@47401800 {
@@ -607,6 +677,7 @@
reg = <0x44d00000 0x4000 /* M3 UMEM */
0x44d80000 0x2000>; /* M3 DMEM */
ti,hwmods = "wkup_m3";
+ ti,no-reset-on-init;
};
elm: elm@48080000 {
@@ -617,6 +688,15 @@
status = "disabled";
};
+ lcdc: lcdc@4830e000 {
+ compatible = "ti,am33xx-tilcdc";
+ reg = <0x4830e000 0x1000>;
+ interrupt-parent = <&intc>;
+ interrupts = <36>;
+ ti,hwmods = "lcdc";
+ status = "disabled";
+ };
+
tscadc: tscadc@44e0d000 {
compatible = "ti,am3359-tscadc";
reg = <0x44e0d000 0x1000>;
@@ -637,6 +717,7 @@
gpmc: gpmc@50000000 {
compatible = "ti,am3352-gpmc";
ti,hwmods = "gpmc";
+ ti,no-idle-on-init;
reg = <0x50000000 0x2000>;
interrupts = <100>;
gpmc,num-cs = <7>;
@@ -645,5 +726,52 @@
#size-cells = <1>;
status = "disabled";
};
+
+ sham: sham@53100000 {
+ compatible = "ti,omap4-sham";
+ ti,hwmods = "sham";
+ reg = <0x53100000 0x200>;
+ interrupts = <109>;
+ dmas = <&edma 36>;
+ dma-names = "rx";
+ };
+
+ aes: aes@53500000 {
+ compatible = "ti,omap4-aes";
+ ti,hwmods = "aes";
+ reg = <0x53500000 0xa0>;
+ interrupts = <103>;
+ dmas = <&edma 6>,
+ <&edma 5>;
+ dma-names = "tx", "rx";
+ };
+
+ mcasp0: mcasp@48038000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ ti,hwmods = "mcasp0";
+ reg = <0x48038000 0x2000>,
+ <0x46000000 0x400000>;
+ reg-names = "mpu", "dat";
+ interrupts = <80>, <81>;
+ interrupts-names = "tx", "rx";
+ status = "disabled";
+ dmas = <&edma 8>,
+ <&edma 9>;
+ dma-names = "tx", "rx";
+ };
+
+ mcasp1: mcasp@4803C000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ ti,hwmods = "mcasp1";
+ reg = <0x4803C000 0x2000>,
+ <0x46400000 0x400000>;
+ reg-names = "mpu", "dat";
+ interrupts = <82>, <83>;
+ interrupts-names = "tx", "rx";
+ status = "disabled";
+ dmas = <&edma 10>,
+ <&edma 11>;
+ dma-names = "tx", "rx";
+ };
};
};
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index ddc1df7..974d103 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -18,12 +18,21 @@
aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
serial0 = &uart0;
+ ethernet0 = &cpsw_emac0;
+ ethernet1 = &cpsw_emac1;
};
cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
cpu@0 {
compatible = "arm,cortex-a9";
+ device_type = "cpu";
+ reg = <0>;
};
};
@@ -35,16 +44,100 @@
<0x48240100 0x0100>;
};
+ l2-cache-controller@48242000 {
+ compatible = "arm,pl310-cache";
+ reg = <0x48242000 0x1000>;
+ cache-unified;
+ cache-level = <2>;
+ };
+
+ am43xx_pinmux: pinmux@44e10800 {
+ compatible = "pinctrl-single";
+ reg = <0x44e10800 0x31c>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0xffffffff>;
+ };
+
ocp {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
+ ti,hwmods = "l3_main";
+
+ edma: edma@49000000 {
+ compatible = "ti,edma3";
+ ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
+ reg = <0x49000000 0x10000>,
+ <0x44e10f90 0x10>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ #dma-cells = <1>;
+ dma-channels = <64>;
+ ti,edma-regions = <4>;
+ ti,edma-slots = <256>;
+ };
uart0: serial@44e09000 {
compatible = "ti,am4372-uart","ti,omap2-uart";
reg = <0x44e09000 0x2000>;
interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "uart1";
+ };
+
+ uart1: serial@48022000 {
+ compatible = "ti,am4372-uart","ti,omap2-uart";
+ reg = <0x48022000 0x2000>;
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "uart2";
+ status = "disabled";
+ };
+
+ uart2: serial@48024000 {
+ compatible = "ti,am4372-uart","ti,omap2-uart";
+ reg = <0x48024000 0x2000>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "uart3";
+ status = "disabled";
+ };
+
+ uart3: serial@481a6000 {
+ compatible = "ti,am4372-uart","ti,omap2-uart";
+ reg = <0x481a6000 0x2000>;
+ interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "uart4";
+ status = "disabled";
+ };
+
+ uart4: serial@481a8000 {
+ compatible = "ti,am4372-uart","ti,omap2-uart";
+ reg = <0x481a8000 0x2000>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "uart5";
+ status = "disabled";
+ };
+
+ uart5: serial@481aa000 {
+ compatible = "ti,am4372-uart","ti,omap2-uart";
+ reg = <0x481aa000 0x2000>;
+ interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "uart6";
+ status = "disabled";
+ };
+
+ mailbox: mailbox@480C8000 {
+ compatible = "ti,omap4-mailbox";
+ reg = <0x480C8000 0x200>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "mailbox";
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <8>;
+ ti,mbox-names = "wkup_m3";
+ ti,mbox-data = <0 0 0 0>;
+ status = "disabled";
};
timer1: timer@44e31000 {
@@ -52,17 +145,523 @@
reg = <0x44e31000 0x400>;
interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
ti,timer-alwon;
+ ti,hwmods = "timer1";
};
timer2: timer@48040000 {
compatible = "ti,am4372-timer","ti,am335x-timer";
reg = <0x48040000 0x400>;
interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "timer2";
+ };
+
+ timer3: timer@48042000 {
+ compatible = "ti,am4372-timer","ti,am335x-timer";
+ reg = <0x48042000 0x400>;
+ interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "timer3";
+ status = "disabled";
+ };
+
+ timer4: timer@48044000 {
+ compatible = "ti,am4372-timer","ti,am335x-timer";
+ reg = <0x48044000 0x400>;
+ interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+ ti,timer-pwm;
+ ti,hwmods = "timer4";
+ status = "disabled";
+ };
+
+ timer5: timer@48046000 {
+ compatible = "ti,am4372-timer","ti,am335x-timer";
+ reg = <0x48046000 0x400>;
+ interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+ ti,timer-pwm;
+ ti,hwmods = "timer5";
+ status = "disabled";
+ };
+
+ timer6: timer@48048000 {
+ compatible = "ti,am4372-timer","ti,am335x-timer";
+ reg = <0x48048000 0x400>;
+ interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+ ti,timer-pwm;
+ ti,hwmods = "timer6";
+ status = "disabled";
+ };
+
+ timer7: timer@4804a000 {
+ compatible = "ti,am4372-timer","ti,am335x-timer";
+ reg = <0x4804a000 0x400>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ ti,timer-pwm;
+ ti,hwmods = "timer7";
+ status = "disabled";
+ };
+
+ timer8: timer@481c1000 {
+ compatible = "ti,am4372-timer","ti,am335x-timer";
+ reg = <0x481c1000 0x400>;
+ interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "timer8";
+ status = "disabled";
+ };
+
+ timer9: timer@4833d000 {
+ compatible = "ti,am4372-timer","ti,am335x-timer";
+ reg = <0x4833d000 0x400>;
+ interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "timer9";
+ status = "disabled";
+ };
+
+ timer10: timer@4833f000 {
+ compatible = "ti,am4372-timer","ti,am335x-timer";
+ reg = <0x4833f000 0x400>;
+ interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "timer10";
+ status = "disabled";
+ };
+
+ timer11: timer@48341000 {
+ compatible = "ti,am4372-timer","ti,am335x-timer";
+ reg = <0x48341000 0x400>;
+ interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "timer11";
+ status = "disabled";
};
counter32k: counter@44e86000 {
compatible = "ti,am4372-counter32k","ti,omap-counter32k";
reg = <0x44e86000 0x40>;
+ ti,hwmods = "counter_32k";
+ };
+
+ rtc@44e3e000 {
+ compatible = "ti,am4372-rtc","ti,da830-rtc";
+ reg = <0x44e3e000 0x1000>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "rtc";
+ status = "disabled";
+ };
+
+ wdt@44e35000 {
+ compatible = "ti,am4372-wdt","ti,omap3-wdt";
+ reg = <0x44e35000 0x1000>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "wd_timer2";
+ };
+
+ gpio0: gpio@44e07000 {
+ compatible = "ti,am4372-gpio","ti,omap4-gpio";
+ reg = <0x44e07000 0x1000>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ ti,hwmods = "gpio1";
+ status = "disabled";
+ };
+
+ gpio1: gpio@4804c000 {
+ compatible = "ti,am4372-gpio","ti,omap4-gpio";
+ reg = <0x4804c000 0x1000>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ ti,hwmods = "gpio2";
+ status = "disabled";
+ };
+
+ gpio2: gpio@481ac000 {
+ compatible = "ti,am4372-gpio","ti,omap4-gpio";
+ reg = <0x481ac000 0x1000>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ ti,hwmods = "gpio3";
+ status = "disabled";
+ };
+
+ gpio3: gpio@481ae000 {
+ compatible = "ti,am4372-gpio","ti,omap4-gpio";
+ reg = <0x481ae000 0x1000>;
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ ti,hwmods = "gpio4";
+ status = "disabled";
+ };
+
+ gpio4: gpio@48320000 {
+ compatible = "ti,am4372-gpio","ti,omap4-gpio";
+ reg = <0x48320000 0x1000>;
+ interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ ti,hwmods = "gpio5";
+ status = "disabled";
+ };
+
+ gpio5: gpio@48322000 {
+ compatible = "ti,am4372-gpio","ti,omap4-gpio";
+ reg = <0x48322000 0x1000>;
+ interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ ti,hwmods = "gpio6";
+ status = "disabled";
+ };
+
+ i2c0: i2c@44e0b000 {
+ compatible = "ti,am4372-i2c","ti,omap4-i2c";
+ reg = <0x44e0b000 0x1000>;
+ interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "i2c1";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@4802a000 {
+ compatible = "ti,am4372-i2c","ti,omap4-i2c";
+ reg = <0x4802a000 0x1000>;
+ interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "i2c2";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@4819c000 {
+ compatible = "ti,am4372-i2c","ti,omap4-i2c";
+ reg = <0x4819c000 0x1000>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "i2c3";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi0: spi@48030000 {
+ compatible = "ti,am4372-mcspi","ti,omap4-mcspi";
+ reg = <0x48030000 0x400>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "spi0";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ mmc1: mmc@48060000 {
+ compatible = "ti,omap4-hsmmc";
+ reg = <0x48060000 0x1000>;
+ ti,hwmods = "mmc1";
+ ti,dual-volt;
+ ti,needs-special-reset;
+ dmas = <&edma 24
+ &edma 25>;
+ dma-names = "tx", "rx";
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ mmc2: mmc@481d8000 {
+ compatible = "ti,omap4-hsmmc";
+ reg = <0x481d8000 0x1000>;
+ ti,hwmods = "mmc2";
+ ti,needs-special-reset;
+ dmas = <&edma 2
+ &edma 3>;
+ dma-names = "tx", "rx";
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ mmc3: mmc@47810000 {
+ compatible = "ti,omap4-hsmmc";
+ reg = <0x47810000 0x1000>;
+ ti,hwmods = "mmc3";
+ ti,needs-special-reset;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ spi1: spi@481a0000 {
+ compatible = "ti,am4372-mcspi","ti,omap4-mcspi";
+ reg = <0x481a0000 0x400>;
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "spi1";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi2: spi@481a2000 {
+ compatible = "ti,am4372-mcspi","ti,omap4-mcspi";
+ reg = <0x481a2000 0x400>;
+ interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "spi2";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi3: spi@481a4000 {
+ compatible = "ti,am4372-mcspi","ti,omap4-mcspi";
+ reg = <0x481a4000 0x400>;
+ interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "spi3";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi4: spi@48345000 {
+ compatible = "ti,am4372-mcspi","ti,omap4-mcspi";
+ reg = <0x48345000 0x400>;
+ interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "spi4";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ mac: ethernet@4a100000 {
+ compatible = "ti,am4372-cpsw","ti,cpsw";
+ reg = <0x4a100000 0x800
+ 0x4a101200 0x100>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ti,hwmods = "cpgmac0";
+ status = "disabled";
+ cpdma_channels = <8>;
+ ale_entries = <1024>;
+ bd_ram_size = <0x2000>;
+ no_bd_ram = <0>;
+ rx_descs = <64>;
+ mac_control = <0x20>;
+ slaves = <2>;
+ active_slave = <0>;
+ cpts_clock_mult = <0x80000000>;
+ cpts_clock_shift = <29>;
+ ranges;
+
+ davinci_mdio: mdio@4a101000 {
+ compatible = "ti,am4372-mdio","ti,davinci_mdio";
+ reg = <0x4a101000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "davinci_mdio";
+ bus_freq = <1000000>;
+ status = "disabled";
+ };
+
+ cpsw_emac0: slave@4a100200 {
+ /* Filled in by U-Boot */
+ mac-address = [ 00 00 00 00 00 00 ];
+ };
+
+ cpsw_emac1: slave@4a100300 {
+ /* Filled in by U-Boot */
+ mac-address = [ 00 00 00 00 00 00 ];
+ };
+ };
+
+ epwmss0: epwmss@48300000 {
+ compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
+ reg = <0x48300000 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ ti,hwmods = "epwmss0";
+ status = "disabled";
+
+ ecap0: ecap@48300100 {
+ compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+ reg = <0x48300100 0x80>;
+ ti,hwmods = "ecap0";
+ status = "disabled";
+ };
+
+ ehrpwm0: ehrpwm@48300200 {
+ compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ reg = <0x48300200 0x80>;
+ ti,hwmods = "ehrpwm0";
+ status = "disabled";
+ };
+ };
+
+ epwmss1: epwmss@48302000 {
+ compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
+ reg = <0x48302000 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ ti,hwmods = "epwmss1";
+ status = "disabled";
+
+ ecap1: ecap@48302100 {
+ compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+ reg = <0x48302100 0x80>;
+ ti,hwmods = "ecap1";
+ status = "disabled";
+ };
+
+ ehrpwm1: ehrpwm@48302200 {
+ compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ reg = <0x48302200 0x80>;
+ ti,hwmods = "ehrpwm1";
+ status = "disabled";
+ };
+ };
+
+ epwmss2: epwmss@48304000 {
+ compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
+ reg = <0x48304000 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ ti,hwmods = "epwmss2";
+ status = "disabled";
+
+ ecap2: ecap@48304100 {
+ compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+ reg = <0x48304100 0x80>;
+ ti,hwmods = "ecap2";
+ status = "disabled";
+ };
+
+ ehrpwm2: ehrpwm@48304200 {
+ compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ reg = <0x48304200 0x80>;
+ ti,hwmods = "ehrpwm2";
+ status = "disabled";
+ };
+ };
+
+ epwmss3: epwmss@48306000 {
+ compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
+ reg = <0x48306000 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ ti,hwmods = "epwmss3";
+ status = "disabled";
+
+ ehrpwm3: ehrpwm@48306200 {
+ compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ reg = <0x48306200 0x80>;
+ ti,hwmods = "ehrpwm3";
+ status = "disabled";
+ };
+ };
+
+ epwmss4: epwmss@48308000 {
+ compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
+ reg = <0x48308000 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ ti,hwmods = "epwmss4";
+ status = "disabled";
+
+ ehrpwm4: ehrpwm@48308200 {
+ compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ reg = <0x48308200 0x80>;
+ ti,hwmods = "ehrpwm4";
+ status = "disabled";
+ };
+ };
+
+ epwmss5: epwmss@4830a000 {
+ compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
+ reg = <0x4830a000 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ ti,hwmods = "epwmss5";
+ status = "disabled";
+
+ ehrpwm5: ehrpwm@4830a200 {
+ compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ reg = <0x4830a200 0x80>;
+ ti,hwmods = "ehrpwm5";
+ status = "disabled";
+ };
+ };
+
+ sham: sham@53100000 {
+ compatible = "ti,omap5-sham";
+ ti,hwmods = "sham";
+ reg = <0x53100000 0x300>;
+ dmas = <&edma 36>;
+ dma-names = "rx";
+ interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ aes: aes@53501000 {
+ compatible = "ti,omap4-aes";
+ ti,hwmods = "aes";
+ reg = <0x53501000 0xa0>;
+ interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&edma 6
+ &edma 5>;
+ dma-names = "tx", "rx";
+ };
+
+ des: des@53701000 {
+ compatible = "ti,omap4-des";
+ ti,hwmods = "des";
+ reg = <0x53701000 0xa0>;
+ interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&edma 34
+ &edma 33>;
+ dma-names = "tx", "rx";
+ };
+
+ mcasp0: mcasp@48038000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ ti,hwmods = "mcasp0";
+ reg = <0x48038000 0x2000>,
+ <0x46000000 0x400000>;
+ reg-names = "mpu", "dat";
+ interrupts = <80>, <81>;
+ interrupts-names = "tx", "rx";
+ status = "disabled";
+ dmas = <&edma 8>,
+ <&edma 9>;
+ dma-names = "tx", "rx";
+ };
+
+ mcasp1: mcasp@4803C000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ ti,hwmods = "mcasp1";
+ reg = <0x4803C000 0x2000>,
+ <0x46400000 0x400000>;
+ reg-names = "mpu", "dat";
+ interrupts = <82>, <83>;
+ interrupts-names = "tx", "rx";
+ status = "disabled";
+ dmas = <&edma 10>,
+ <&edma 11>;
+ dma-names = "tx", "rx";
};
};
};
diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts
index 74174d4..fbf9c4c 100644
--- a/arch/arm/boot/dts/am43x-epos-evm.dts
+++ b/arch/arm/boot/dts/am43x-epos-evm.dts
@@ -11,8 +11,176 @@
/dts-v1/;
#include "am4372.dtsi"
+#include <dt-bindings/pinctrl/am43xx.h>
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "TI AM43x EPOS EVM";
compatible = "ti,am43x-epos-evm","ti,am4372","ti,am43";
+
+ vmmcsd_fixed: fixedregulator-sd {
+ compatible = "regulator-fixed";
+ regulator-name = "vmmcsd_fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ };
+
+ am43xx_pinmux: pinmux@44e10800 {
+ cpsw_default: cpsw_default {
+ pinctrl-single,pins = <
+ /* Slave 1 */
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxerr.rmii1_rxerr */
+ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txen.rmii1_txen */
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxdv.rmii1_rxdv */
+ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */
+ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk.rmii1_refclk */
+ >;
+ };
+
+ cpsw_sleep: cpsw_sleep {
+ pinctrl-single,pins = <
+ /* Slave 1 reset value */
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ davinci_mdio_default: davinci_mdio_default {
+ pinctrl-single,pins = <
+ /* MDIO */
+ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
+
+ davinci_mdio_sleep: davinci_mdio_sleep {
+ pinctrl-single,pins = <
+ /* MDIO reset value */
+ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+ };
+
+ matrix_keypad: matrix_keypad@0 {
+ compatible = "gpio-matrix-keypad";
+ debounce-delay-ms = <5>;
+ col-scan-delay-us = <2>;
+
+ row-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH /* Bank0, pin12 */
+ &gpio0 13 GPIO_ACTIVE_HIGH /* Bank0, pin13 */
+ &gpio0 14 GPIO_ACTIVE_HIGH /* Bank0, pin14 */
+ &gpio0 15 GPIO_ACTIVE_HIGH>; /* Bank0, pin15 */
+
+ col-gpios = <&gpio3 9 GPIO_ACTIVE_HIGH /* Bank3, pin9 */
+ &gpio3 10 GPIO_ACTIVE_HIGH /* Bank3, pin10 */
+ &gpio2 18 GPIO_ACTIVE_HIGH /* Bank2, pin18 */
+ &gpio2 19 GPIO_ACTIVE_HIGH>; /* Bank2, pin19 */
+
+ linux,keymap = <0x00000201 /* P1 */
+ 0x01000204 /* P4 */
+ 0x02000207 /* P7 */
+ 0x0300020a /* NUMERIC_STAR */
+ 0x00010202 /* P2 */
+ 0x01010205 /* P5 */
+ 0x02010208 /* P8 */
+ 0x03010200 /* P0 */
+ 0x00020203 /* P3 */
+ 0x01020206 /* P6 */
+ 0x02020209 /* P9 */
+ 0x0302020b /* NUMERIC_POUND */
+ 0x00030067 /* UP */
+ 0x0103006a /* RIGHT */
+ 0x0203006c /* DOWN */
+ 0x03030069>; /* LEFT */
+ };
+};
+
+&mmc1 {
+ status = "okay";
+ vmmc-supply = <&vmmcsd_fixed>;
+ bus-width = <4>;
+};
+
+&mac {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&cpsw_default>;
+ pinctrl-1 = <&cpsw_sleep>;
+ status = "okay";
+};
+
+&davinci_mdio {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&davinci_mdio_default>;
+ pinctrl-1 = <&davinci_mdio_sleep>;
+ status = "okay";
+};
+
+&cpsw_emac0 {
+ phy_id = <&davinci_mdio>, <16>;
+ phy-mode = "rmii";
+};
+
+&cpsw_emac1 {
+ phy_id = <&davinci_mdio>, <1>;
+ phy-mode = "rmii";
+};
+
+&i2c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ at24@50 {
+ compatible = "at24,24c256";
+ pagesize = <64>;
+ reg = <0x50>;
+ };
+
+ pixcir_ts@5c {
+ compatible = "pixcir,pixcir_ts";
+ reg = <0x5c>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <17 0>;
+
+ attb-gpio = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+
+ x-size = <1024>;
+ y-size = <768>;
+ };
+};
+
+&gpio0 {
+ status = "okay";
+};
+
+&gpio1 {
+ status = "okay";
+};
+
+&gpio2 {
+ status = "okay";
+};
+
+&gpio3 {
+ status = "okay";
};
diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi
index 1de2dae..00d6a79 100644
--- a/arch/arm/boot/dts/armada-370-xp.dtsi
+++ b/arch/arm/boot/dts/armada-370-xp.dtsi
@@ -113,6 +113,7 @@
#interrupt-cells = <1>;
#size-cells = <1>;
interrupt-controller;
+ msi-controller;
};
coherency-fabric@20200 {
@@ -137,6 +138,14 @@
status = "disabled";
};
+ coredivclk: corediv-clock@18740 {
+ compatible = "marvell,armada-370-corediv-clock";
+ reg = <0x18740 0xc>;
+ #clock-cells = <1>;
+ clocks = <&mainpll>;
+ clock-output-names = "nand";
+ };
+
timer@20300 {
reg = <0x20300 0x30>, <0x21040 0x30>;
interrupts = <37>, <38>, <39>, <40>, <5>, <6>;
@@ -176,7 +185,6 @@
i2c0: i2c@11000 {
compatible = "marvell,mv64xxx-i2c";
- reg = <0x11000 0x20>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <31>;
@@ -187,7 +195,6 @@
i2c1: i2c@11100 {
compatible = "marvell,mv64xxx-i2c";
- reg = <0x11100 0x20>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <32>;
@@ -252,4 +259,13 @@
};
};
+
+ clocks {
+ /* 2 GHz fixed main PLL */
+ mainpll: mainpll {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <2000000000>;
+ };
+ };
};
diff --git a/arch/arm/boot/dts/armada-370.dtsi b/arch/arm/boot/dts/armada-370.dtsi
index e134d7a..7a4b82e 100644
--- a/arch/arm/boot/dts/armada-370.dtsi
+++ b/arch/arm/boot/dts/armada-370.dtsi
@@ -44,6 +44,7 @@
#address-cells = <3>;
#size-cells = <2>;
+ msi-parent = <&mpic>;
bus-range = <0x00 0xff>;
ranges =
@@ -218,6 +219,14 @@
};
};
+ i2c0: i2c@11000 {
+ reg = <0x11000 0x20>;
+ };
+
+ i2c1: i2c@11100 {
+ reg = <0x11100 0x20>;
+ };
+
usb@50000 {
clocks = <&coreclk 0>;
};
diff --git a/arch/arm/boot/dts/armada-xp-matrix.dts b/arch/arm/boot/dts/armada-xp-matrix.dts
new file mode 100644
index 0000000..e47c49e
--- /dev/null
+++ b/arch/arm/boot/dts/armada-xp-matrix.dts
@@ -0,0 +1,75 @@
+/*
+ * Device Tree file for Marvell Armada XP Matrix board
+ *
+ * Copyright (C) 2013 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+#include "armada-xp-mv78460.dtsi"
+
+/ {
+ model = "Marvell Armada XP Matrix Board";
+ compatible = "marvell,axp-matrix", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 earlyprintk";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x00000000 0 0x80000000>; /* 2 GB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>;
+
+ internal-regs {
+ serial@12000 {
+ clock-frequency = <250000000>;
+ status = "okay";
+ };
+ serial@12100 {
+ clock-frequency = <250000000>;
+ status = "okay";
+ };
+ serial@12200 {
+ clock-frequency = <250000000>;
+ status = "okay";
+ };
+ serial@12300 {
+ clock-frequency = <250000000>;
+ status = "okay";
+ };
+
+ sata@a0000 {
+ nr-ports = <2>;
+ status = "okay";
+ };
+
+ ethernet@30000 {
+ status = "okay";
+ phy-mode = "sgmii";
+ };
+
+ pcie-controller {
+ status = "okay";
+
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+ };
+
+ usb@50000 {
+ status = "okay";
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/armada-xp-mv78230.dtsi b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
index 0358a33..3f5e612 100644
--- a/arch/arm/boot/dts/armada-xp-mv78230.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
@@ -57,6 +57,7 @@
#address-cells = <3>;
#size-cells = <2>;
+ msi-parent = <&mpic>;
bus-range = <0x00 0xff>;
ranges =
diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
index 0e82c50..3e9fd13 100644
--- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
@@ -58,6 +58,7 @@
#address-cells = <3>;
#size-cells = <2>;
+ msi-parent = <&mpic>;
bus-range = <0x00 0xff>;
ranges =
diff --git a/arch/arm/boot/dts/armada-xp-mv78460.dtsi b/arch/arm/boot/dts/armada-xp-mv78460.dtsi
index e82c1b8..31ba6d8 100644
--- a/arch/arm/boot/dts/armada-xp-mv78460.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78460.dtsi
@@ -74,6 +74,7 @@
#address-cells = <3>;
#size-cells = <2>;
+ msi-parent = <&mpic>;
bus-range = <0x00 0xff>;
ranges =
diff --git a/arch/arm/boot/dts/armada-xp.dtsi b/arch/arm/boot/dts/armada-xp.dtsi
index 3058522..281c644 100644
--- a/arch/arm/boot/dts/armada-xp.dtsi
+++ b/arch/arm/boot/dts/armada-xp.dtsi
@@ -147,6 +147,16 @@
};
};
+ i2c0: i2c@11000 {
+ compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c";
+ reg = <0x11000 0x100>;
+ };
+
+ i2c1: i2c@11100 {
+ compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c";
+ reg = <0x11100 0x100>;
+ };
+
usb@50000 {
clocks = <&gateclk 18>;
};
diff --git a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
index 1373546..cb2c010 100644
--- a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
+++ b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
@@ -96,7 +96,6 @@
};
spi0: spi@fffc8000 {
- status = "okay";
cs-gpios = <0>, <&pioC 11 0>, <0>, <0>;
mtd_dataflash@0 {
compatible = "atmel,at45", "atmel,dataflash";
diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi
index 9fb7ffd..6224f9f 100644
--- a/arch/arm/boot/dts/at91sam9n12.dtsi
+++ b/arch/arm/boot/dts/at91sam9n12.dtsi
@@ -437,6 +437,9 @@
compatible = "atmel,at91sam9g45-ssc";
reg = <0xf0010000 0x4000>;
interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
+ dmas = <&dma 0 AT91_DMA_CFG_PER_ID(21)>,
+ <&dma 0 AT91_DMA_CFG_PER_ID(22)>;
+ dma-names = "tx", "rx";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
status = "disabled";
diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts
index 27a9352..e9487f6 100644
--- a/arch/arm/boot/dts/at91sam9n12ek.dts
+++ b/arch/arm/boot/dts/at91sam9n12ek.dts
@@ -38,9 +38,18 @@
status = "okay";
};
+ ssc0: ssc@f0010000 {
+ status = "okay";
+ };
+
i2c0: i2c@f8010000 {
status = "okay";
+ wm8904: codec@1a {
+ compatible = "wm8904";
+ reg = <0x1a>;
+ };
+
qt1070: keyboard@1b {
compatible = "qt1070";
reg = <0x1b>;
@@ -82,6 +91,13 @@
<AT91_PIOA 2 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
};
};
+
+ sound {
+ pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
+ atmel,pins =
+ <AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+ };
};
spi0: spi@f0000000 {
@@ -142,4 +158,22 @@
gpio-key,wakeup;
};
};
+
+ sound {
+ compatible = "atmel,asoc-wm8904";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
+
+ atmel,model = "wm8904 @ AT91SAM9N12";
+ atmel,audio-routing =
+ "Headphone Jack", "HPOUTL",
+ "Headphone Jack", "HPOUTR",
+ "IN2L", "Line In Jack",
+ "IN2R", "Line In Jack",
+ "Mic", "MICBIAS",
+ "IN1L", "Mic";
+
+ atmel,ssc-controller = <&ssc0>;
+ atmel,audio-codec = <&wm8904>;
+ };
};
diff --git a/arch/arm/boot/dts/dove-cm-a510.dts b/arch/arm/boot/dts/dove-cm-a510.dts
index 61a8062..50c0d69 100644
--- a/arch/arm/boot/dts/dove-cm-a510.dts
+++ b/arch/arm/boot/dts/dove-cm-a510.dts
@@ -1,6 +1,6 @@
/dts-v1/;
-/include/ "dove.dtsi"
+#include "dove.dtsi"
/ {
model = "Compulab CM-A510";
diff --git a/arch/arm/boot/dts/dove-cubox.dts b/arch/arm/boot/dts/dove-cubox.dts
index 022646e..8349a24 100644
--- a/arch/arm/boot/dts/dove-cubox.dts
+++ b/arch/arm/boot/dts/dove-cubox.dts
@@ -1,6 +1,6 @@
/dts-v1/;
-/include/ "dove.dtsi"
+#include "dove.dtsi"
/ {
model = "SolidRun CuBox";
@@ -99,19 +99,13 @@
silabs,pll-master;
};
- clkout1 {
- reg = <1>;
+ clkout2 {
+ reg = <2>;
silabs,drive-strength = <8>;
silabs,multisynth-source = <1>;
silabs,clock-source = <0>;
silabs,pll-master;
};
-
- clkout2 {
- reg = <2>;
- silabs,multisynth-source = <1>;
- silabs,clock-source = <0>;
- };
};
};
@@ -132,3 +126,11 @@
reg = <0>;
};
};
+
+&audio1 {
+ status = "okay";
+ clocks = <&gate_clk 13>, <&si5351 2>;
+ clock-names = "internal", "extclk";
+ pinctrl-0 = <&pmx_audio1_i2s1_spdifo &pmx_audio1_extclk>;
+ pinctrl-names = "default";
+};
diff --git a/arch/arm/boot/dts/dove-d2plug.dts b/arch/arm/boot/dts/dove-d2plug.dts
index e2222ce..c11d363 100644
--- a/arch/arm/boot/dts/dove-d2plug.dts
+++ b/arch/arm/boot/dts/dove-d2plug.dts
@@ -1,6 +1,6 @@
/dts-v1/;
-/include/ "dove.dtsi"
+#include "dove.dtsi"
/ {
model = "Globalscale D2Plug";
diff --git a/arch/arm/boot/dts/dove-d3plug.dts b/arch/arm/boot/dts/dove-d3plug.dts
new file mode 100644
index 0000000..f5f59bb
--- /dev/null
+++ b/arch/arm/boot/dts/dove-d3plug.dts
@@ -0,0 +1,103 @@
+/dts-v1/;
+
+#include "dove.dtsi"
+
+/ {
+ model = "Globalscale D3Plug";
+ compatible = "globalscale,d3plug", "marvell,dove";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x40000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/mmcblk0p2 rw rootwait";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_gpio_0 &pmx_gpio_1 &pmx_gpio_2>;
+ pinctrl-names = "default";
+
+ wlan-act {
+ label = "wlan-act";
+ gpios = <&gpio0 0 1>;
+ };
+
+ wlan-ap {
+ label = "wlan-ap";
+ gpios = <&gpio0 1 1>;
+ };
+
+ status {
+ label = "status";
+ gpios = <&gpio0 2 1>;
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb_power: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 8 0>;
+ pinctrl-0 = <&pmx_gpio_8>;
+ pinctrl-names = "default";
+ };
+ };
+};
+
+&uart0 { status = "okay"; };
+&sata0 { status = "okay"; };
+&i2c0 { status = "okay"; };
+
+/* Samsung M8G2F eMMC */
+&sdio0 {
+ status = "okay";
+ non-removable;
+ bus-width = <4>;
+};
+
+/* Marvell SD8787 WLAN/BT */
+&sdio1 {
+ status = "okay";
+ non-removable;
+};
+
+&spi0 {
+ status = "okay";
+
+ /* spi0.0: 2M Flash Macronix MX25L1605D */
+ spi-flash@0 {
+ compatible = "st,m25l1605d";
+ spi-max-frequency = <86000000>;
+ reg = <0>;
+ };
+};
+
+&pcie {
+ status = "okay";
+ /* Fresco Logic USB3.0 xHCI controller */
+ pcie-port@0 {
+ status = "okay";
+ reset-gpios = <&gpio0 26 1>;
+ reset-delay-us = <20000>;
+ pinctrl-0 = <&pmx_camera_gpio>;
+ pinctrl-names = "default";
+ };
+ /* Mini-PCIe slot */
+ pcie-port@1 {
+ status = "okay";
+ reset-gpios = <&gpio0 25 1>;
+ };
+};
diff --git a/arch/arm/boot/dts/dove-dove-db.dts b/arch/arm/boot/dts/dove-dove-db.dts
index e5a920b..bb725dc 100644
--- a/arch/arm/boot/dts/dove-dove-db.dts
+++ b/arch/arm/boot/dts/dove-dove-db.dts
@@ -1,6 +1,6 @@
/dts-v1/;
-/include/ "dove.dtsi"
+#include "dove.dtsi"
/ {
model = "Marvell DB-MV88AP510-BP Development Board";
diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi
index cc27916..113a8bc 100644
--- a/arch/arm/boot/dts/dove.dtsi
+++ b/arch/arm/boot/dts/dove.dtsi
@@ -1,8 +1,11 @@
/include/ "skeleton.dtsi"
+#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
+
/ {
compatible = "marvell,dove";
model = "Marvell Armada 88AP510 SoC";
+ interrupt-parent = <&intc>;
aliases {
gpio0 = &gpio0;
@@ -27,482 +30,576 @@
marvell,tauros2-cache-features = <0>;
};
- soc@f1000000 {
- compatible = "simple-bus";
- #address-cells = <1>;
+ mbus {
+ compatible = "marvell,dove-mbus", "marvell,mbus", "simple-bus";
+ #address-cells = <2>;
#size-cells = <1>;
- interrupt-parent = <&intc>;
+ controller = <&mbusc>;
+ pcie-mem-aperture = <0xe0000000 0x10000000>; /* 256M MEM space */
+ pcie-io-aperture = <0xf2000000 0x00200000>; /* 2M I/O space */
- ranges = <0xc8000000 0xc8000000 0x0100000 /* CESA SRAM 1M */
- 0xe0000000 0xe0000000 0x8000000 /* PCIe0 Mem 128M */
- 0xe8000000 0xe8000000 0x8000000 /* PCIe1 Mem 128M */
- 0xf0000000 0xf0000000 0x0100000 /* ScratchPad 1M */
- 0x00000000 0xf1000000 0x1000000 /* SB/NB regs 16M */
- 0xf2000000 0xf2000000 0x0100000 /* PCIe0 I/O 1M */
- 0xf2100000 0xf2100000 0x0100000 /* PCIe0 I/O 1M */
- 0xf8000000 0xf8000000 0x8000000>; /* BootROM 128M */
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x0100000 /* MBUS regs 1M */
+ MBUS_ID(0xf0, 0x02) 0 0xf1800000 0x1000000 /* AXI regs 16M */
+ MBUS_ID(0x01, 0xfd) 0 0xf8000000 0x8000000 /* BootROM 128M */
+ MBUS_ID(0x03, 0x01) 0 0xc8000000 0x0100000 /* CESA SRAM 1M */
+ MBUS_ID(0x0d, 0x00) 0 0xf0000000 0x0100000>; /* PMU SRAM 1M */
- timer: timer@20300 {
- compatible = "marvell,orion-timer";
- reg = <0x20300 0x20>;
- interrupt-parent = <&bridge_intc>;
- interrupts = <1>, <2>;
- clocks = <&core_clk 0>;
- };
-
- intc: main-interrupt-ctrl@20200 {
- compatible = "marvell,orion-intc";
- interrupt-controller;
- #interrupt-cells = <1>;
- reg = <0x20200 0x10>, <0x20210 0x10>;
- };
-
- bridge_intc: bridge-interrupt-ctrl@20110 {
- compatible = "marvell,orion-bridge-intc";
- interrupt-controller;
- #interrupt-cells = <1>;
- reg = <0x20110 0x8>;
- interrupts = <0>;
- marvell,#interrupts = <5>;
- };
-
- core_clk: core-clocks@d0214 {
- compatible = "marvell,dove-core-clock";
- reg = <0xd0214 0x4>;
- #clock-cells = <1>;
- };
-
- gate_clk: clock-gating-ctrl@d0038 {
- compatible = "marvell,dove-gating-clock";
- reg = <0xd0038 0x4>;
- clocks = <&core_clk 0>;
- #clock-cells = <1>;
- };
-
- thermal: thermal-diode@d001c {
- compatible = "marvell,dove-thermal";
- reg = <0xd001c 0x0c>, <0xd005c 0x08>;
- };
-
- uart0: serial@12000 {
- compatible = "ns16550a";
- reg = <0x12000 0x100>;
- reg-shift = <2>;
- interrupts = <7>;
- clocks = <&core_clk 0>;
+ pcie: pcie-controller {
+ compatible = "marvell,dove-pcie";
status = "disabled";
- };
+ device_type = "pci";
+ #address-cells = <3>;
+ #size-cells = <2>;
- uart1: serial@12100 {
- compatible = "ns16550a";
- reg = <0x12100 0x100>;
- reg-shift = <2>;
- interrupts = <8>;
- clocks = <&core_clk 0>;
- pinctrl-0 = <&pmx_uart1>;
- pinctrl-names = "default";
- status = "disabled";
- };
+ msi-parent = <&intc>;
+ bus-range = <0x00 0xff>;
- uart2: serial@12200 {
- compatible = "ns16550a";
- reg = <0x12000 0x100>;
- reg-shift = <2>;
- interrupts = <9>;
- clocks = <&core_clk 0>;
- status = "disabled";
- };
+ ranges = <0x82000000 0x0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x2000
+ 0x82000000 0x0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x2000
+ 0x82000000 0x1 0x0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 Mem */
+ 0x81000000 0x1 0x0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 I/O */
+ 0x82000000 0x2 0x0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 Mem */
+ 0x81000000 0x2 0x0 MBUS_ID(0x08, 0xe0) 0 1 0>; /* Port 1.0 I/O */
- uart3: serial@12300 {
- compatible = "ns16550a";
- reg = <0x12100 0x100>;
- reg-shift = <2>;
- interrupts = <10>;
- clocks = <&core_clk 0>;
- status = "disabled";
- };
+ pcie-port@0 {
+ device_type = "pci";
+ status = "disabled";
+ assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ clocks = <&gate_clk 4>;
+ marvell,pcie-port = <0>;
- gpio0: gpio-ctrl@d0400 {
- compatible = "marvell,orion-gpio";
- #gpio-cells = <2>;
- gpio-controller;
- reg = <0xd0400 0x20>;
- ngpios = <32>;
- interrupt-controller;
- #interrupt-cells = <2>;
- interrupts = <12>, <13>, <14>, <60>;
- };
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+ 0x81000000 0 0 0x81000000 0x1 0 1 0>;
- gpio1: gpio-ctrl@d0420 {
- compatible = "marvell,orion-gpio";
- #gpio-cells = <2>;
- gpio-controller;
- reg = <0xd0420 0x20>;
- ngpios = <32>;
- interrupt-controller;
- #interrupt-cells = <2>;
- interrupts = <61>;
- };
-
- gpio2: gpio-ctrl@e8400 {
- compatible = "marvell,orion-gpio";
- #gpio-cells = <2>;
- gpio-controller;
- reg = <0xe8400 0x0c>;
- ngpios = <8>;
- };
-
- pinctrl: pin-ctrl@d0200 {
- compatible = "marvell,dove-pinctrl";
- reg = <0xd0200 0x10>;
- clocks = <&gate_clk 22>;
-
- pmx_gpio_0: pmx-gpio-0 {
- marvell,pins = "mpp0";
- marvell,function = "gpio";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &intc 16>;
};
- pmx_gpio_1: pmx-gpio-1 {
- marvell,pins = "mpp1";
- marvell,function = "gpio";
- };
+ pcie-port@1 {
+ device_type = "pci";
+ status = "disabled";
+ assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
+ reg = <0x1000 0 0 0 0>;
+ clocks = <&gate_clk 5>;
+ marvell,pcie-port = <1>;
- pmx_gpio_2: pmx-gpio-2 {
- marvell,pins = "mpp2";
- marvell,function = "gpio";
- };
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+ 0x81000000 0 0 0x81000000 0x2 0 1 0>;
- pmx_gpio_3: pmx-gpio-3 {
- marvell,pins = "mpp3";
- marvell,function = "gpio";
- };
-
- pmx_gpio_4: pmx-gpio-4 {
- marvell,pins = "mpp4";
- marvell,function = "gpio";
- };
-
- pmx_gpio_5: pmx-gpio-5 {
- marvell,pins = "mpp5";
- marvell,function = "gpio";
- };
-
- pmx_gpio_6: pmx-gpio-6 {
- marvell,pins = "mpp6";
- marvell,function = "gpio";
- };
-
- pmx_gpio_7: pmx-gpio-7 {
- marvell,pins = "mpp7";
- marvell,function = "gpio";
- };
-
- pmx_gpio_8: pmx-gpio-8 {
- marvell,pins = "mpp8";
- marvell,function = "gpio";
- };
-
- pmx_gpio_9: pmx-gpio-9 {
- marvell,pins = "mpp9";
- marvell,function = "gpio";
- };
-
- pmx_gpio_10: pmx-gpio-10 {
- marvell,pins = "mpp10";
- marvell,function = "gpio";
- };
-
- pmx_gpio_11: pmx-gpio-11 {
- marvell,pins = "mpp11";
- marvell,function = "gpio";
- };
-
- pmx_gpio_12: pmx-gpio-12 {
- marvell,pins = "mpp12";
- marvell,function = "gpio";
- };
-
- pmx_gpio_13: pmx-gpio-13 {
- marvell,pins = "mpp13";
- marvell,function = "gpio";
- };
-
- pmx_gpio_14: pmx-gpio-14 {
- marvell,pins = "mpp14";
- marvell,function = "gpio";
- };
-
- pmx_gpio_15: pmx-gpio-15 {
- marvell,pins = "mpp15";
- marvell,function = "gpio";
- };
-
- pmx_gpio_16: pmx-gpio-16 {
- marvell,pins = "mpp16";
- marvell,function = "gpio";
- };
-
- pmx_gpio_17: pmx-gpio-17 {
- marvell,pins = "mpp17";
- marvell,function = "gpio";
- };
-
- pmx_gpio_18: pmx-gpio-18 {
- marvell,pins = "mpp18";
- marvell,function = "gpio";
- };
-
- pmx_gpio_19: pmx-gpio-19 {
- marvell,pins = "mpp19";
- marvell,function = "gpio";
- };
-
- pmx_gpio_20: pmx-gpio-20 {
- marvell,pins = "mpp20";
- marvell,function = "gpio";
- };
-
- pmx_gpio_21: pmx-gpio-21 {
- marvell,pins = "mpp21";
- marvell,function = "gpio";
- };
-
- pmx_camera: pmx-camera {
- marvell,pins = "mpp_camera";
- marvell,function = "camera";
- };
-
- pmx_camera_gpio: pmx-camera-gpio {
- marvell,pins = "mpp_camera";
- marvell,function = "gpio";
- };
-
- pmx_sdio0: pmx-sdio0 {
- marvell,pins = "mpp_sdio0";
- marvell,function = "sdio0";
- };
-
- pmx_sdio0_gpio: pmx-sdio0-gpio {
- marvell,pins = "mpp_sdio0";
- marvell,function = "gpio";
- };
-
- pmx_sdio1: pmx-sdio1 {
- marvell,pins = "mpp_sdio1";
- marvell,function = "sdio1";
- };
-
- pmx_sdio1_gpio: pmx-sdio1-gpio {
- marvell,pins = "mpp_sdio1";
- marvell,function = "gpio";
- };
-
- pmx_audio1_gpio: pmx-audio1-gpio {
- marvell,pins = "mpp_audio1";
- marvell,function = "gpio";
- };
-
- pmx_spi0: pmx-spi0 {
- marvell,pins = "mpp_spi0";
- marvell,function = "spi0";
- };
-
- pmx_spi0_gpio: pmx-spi0-gpio {
- marvell,pins = "mpp_spi0";
- marvell,function = "gpio";
- };
-
- pmx_uart1: pmx-uart1 {
- marvell,pins = "mpp_uart1";
- marvell,function = "uart1";
- };
-
- pmx_uart1_gpio: pmx-uart1-gpio {
- marvell,pins = "mpp_uart1";
- marvell,function = "gpio";
- };
-
- pmx_nand: pmx-nand {
- marvell,pins = "mpp_nand";
- marvell,function = "nand";
- };
-
- pmx_nand_gpo: pmx-nand-gpo {
- marvell,pins = "mpp_nand";
- marvell,function = "gpo";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &intc 18>;
};
};
- spi0: spi-ctrl@10600 {
- compatible = "marvell,orion-spi";
+ internal-regs {
+ compatible = "simple-bus";
#address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- interrupts = <6>;
- reg = <0x10600 0x28>;
- clocks = <&core_clk 0>;
- pinctrl-0 = <&pmx_spi0>;
- pinctrl-names = "default";
- status = "disabled";
- };
+ #size-cells = <1>;
+ ranges = <0x00000000 MBUS_ID(0xf0, 0x01) 0 0x0100000 /* MBUS regs 1M */
+ 0x00800000 MBUS_ID(0xf0, 0x02) 0 0x1000000 /* AXI regs 16M */
+ 0xffffe000 MBUS_ID(0x03, 0x01) 0 0x0000800 /* CESA SRAM 2k */
+ 0xfffff000 MBUS_ID(0x0d, 0x00) 0 0x0000800>; /* PMU SRAM 2k */
- spi1: spi-ctrl@14600 {
- compatible = "marvell,orion-spi";
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- interrupts = <5>;
- reg = <0x14600 0x28>;
- clocks = <&core_clk 0>;
- status = "disabled";
- };
-
- i2c0: i2c-ctrl@11000 {
- compatible = "marvell,mv64xxx-i2c";
- reg = <0x11000 0x20>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <11>;
- clock-frequency = <400000>;
- timeout-ms = <1000>;
- clocks = <&core_clk 0>;
- status = "disabled";
- };
-
- ehci0: usb-host@50000 {
- compatible = "marvell,orion-ehci";
- reg = <0x50000 0x1000>;
- interrupts = <24>;
- clocks = <&gate_clk 0>;
- status = "okay";
- };
-
- ehci1: usb-host@51000 {
- compatible = "marvell,orion-ehci";
- reg = <0x51000 0x1000>;
- interrupts = <25>;
- clocks = <&gate_clk 1>;
- status = "okay";
- };
-
- sdio0: sdio-host@92000 {
- compatible = "marvell,dove-sdhci";
- reg = <0x92000 0x100>;
- interrupts = <35>, <37>;
- clocks = <&gate_clk 8>;
- pinctrl-0 = <&pmx_sdio0>;
- pinctrl-names = "default";
- status = "disabled";
- };
-
- sdio1: sdio-host@90000 {
- compatible = "marvell,dove-sdhci";
- reg = <0x90000 0x100>;
- interrupts = <36>, <38>;
- clocks = <&gate_clk 9>;
- pinctrl-0 = <&pmx_sdio1>;
- pinctrl-names = "default";
- status = "disabled";
- };
-
- sata0: sata-host@a0000 {
- compatible = "marvell,orion-sata";
- reg = <0xa0000 0x2400>;
- interrupts = <62>;
- clocks = <&gate_clk 3>;
- nr-ports = <1>;
- status = "disabled";
- };
-
- rtc: real-time-clock@d8500 {
- compatible = "marvell,orion-rtc";
- reg = <0xd8500 0x20>;
- };
-
- crypto: crypto-engine@30000 {
- compatible = "marvell,orion-crypto";
- reg = <0x30000 0x10000>,
- <0xc8000000 0x800>;
- reg-names = "regs", "sram";
- interrupts = <31>;
- clocks = <&gate_clk 15>;
- status = "okay";
- };
-
- xor0: dma-engine@60800 {
- compatible = "marvell,orion-xor";
- reg = <0x60800 0x100
- 0x60a00 0x100>;
- clocks = <&gate_clk 23>;
- status = "okay";
-
- channel0 {
- interrupts = <39>;
- dmacap,memcpy;
- dmacap,xor;
+ mbusc: mbus-ctrl@20000 {
+ compatible = "marvell,mbus-controller";
+ reg = <0x20000 0x80>, <0x800100 0x8>;
};
- channel1 {
- interrupts = <40>;
- dmacap,memset;
- dmacap,memcpy;
- dmacap,xor;
- };
- };
-
- xor1: dma-engine@60900 {
- compatible = "marvell,orion-xor";
- reg = <0x60900 0x100
- 0x60b00 0x100>;
- clocks = <&gate_clk 24>;
- status = "okay";
-
- channel0 {
- interrupts = <42>;
- dmacap,memcpy;
- dmacap,xor;
+ timer: timer@20300 {
+ compatible = "marvell,orion-timer";
+ reg = <0x20300 0x20>;
+ interrupt-parent = <&bridge_intc>;
+ interrupts = <1>, <2>;
+ clocks = <&core_clk 0>;
};
- channel1 {
- interrupts = <43>;
- dmacap,memset;
- dmacap,memcpy;
- dmacap,xor;
+ intc: main-interrupt-ctrl@20200 {
+ compatible = "marvell,orion-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x20200 0x10>, <0x20210 0x10>;
};
- };
- mdio: mdio-bus@72004 {
- compatible = "marvell,orion-mdio";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x72004 0x84>;
- interrupts = <30>;
- clocks = <&gate_clk 2>;
- status = "disabled";
-
- ethphy: ethernet-phy {
- device-type = "ethernet-phy";
- /* set phy address in board file */
+ bridge_intc: bridge-interrupt-ctrl@20110 {
+ compatible = "marvell,orion-bridge-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x20110 0x8>;
+ interrupts = <0>;
+ marvell,#interrupts = <5>;
};
- };
- eth: ethernet-controller@72000 {
- compatible = "marvell,orion-eth";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x72000 0x4000>;
- clocks = <&gate_clk 2>;
- marvell,tx-checksum-limit = <1600>;
- status = "disabled";
+ core_clk: core-clocks@d0214 {
+ compatible = "marvell,dove-core-clock";
+ reg = <0xd0214 0x4>;
+ #clock-cells = <1>;
+ };
- ethernet-port@0 {
- device_type = "network";
- compatible = "marvell,orion-eth-port";
- reg = <0>;
- interrupts = <29>;
- /* overwrite MAC address in bootloader */
- local-mac-address = [00 00 00 00 00 00];
- phy-handle = <ðphy>;
+ gate_clk: clock-gating-ctrl@d0038 {
+ compatible = "marvell,dove-gating-clock";
+ reg = <0xd0038 0x4>;
+ clocks = <&core_clk 0>;
+ #clock-cells = <1>;
+ };
+
+ thermal: thermal-diode@d001c {
+ compatible = "marvell,dove-thermal";
+ reg = <0xd001c 0x0c>, <0xd005c 0x08>;
+ };
+
+ uart0: serial@12000 {
+ compatible = "ns16550a";
+ reg = <0x12000 0x100>;
+ reg-shift = <2>;
+ interrupts = <7>;
+ clocks = <&core_clk 0>;
+ status = "disabled";
+ };
+
+ uart1: serial@12100 {
+ compatible = "ns16550a";
+ reg = <0x12100 0x100>;
+ reg-shift = <2>;
+ interrupts = <8>;
+ clocks = <&core_clk 0>;
+ pinctrl-0 = <&pmx_uart1>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ uart2: serial@12200 {
+ compatible = "ns16550a";
+ reg = <0x12000 0x100>;
+ reg-shift = <2>;
+ interrupts = <9>;
+ clocks = <&core_clk 0>;
+ status = "disabled";
+ };
+
+ uart3: serial@12300 {
+ compatible = "ns16550a";
+ reg = <0x12100 0x100>;
+ reg-shift = <2>;
+ interrupts = <10>;
+ clocks = <&core_clk 0>;
+ status = "disabled";
+ };
+
+ gpio0: gpio-ctrl@d0400 {
+ compatible = "marvell,orion-gpio";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0xd0400 0x20>;
+ ngpios = <32>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <12>, <13>, <14>, <60>;
+ };
+
+ gpio1: gpio-ctrl@d0420 {
+ compatible = "marvell,orion-gpio";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0xd0420 0x20>;
+ ngpios = <32>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <61>;
+ };
+
+ gpio2: gpio-ctrl@e8400 {
+ compatible = "marvell,orion-gpio";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0xe8400 0x0c>;
+ ngpios = <8>;
+ };
+
+ pinctrl: pin-ctrl@d0200 {
+ compatible = "marvell,dove-pinctrl";
+ reg = <0xd0200 0x10>;
+ clocks = <&gate_clk 22>;
+
+ pmx_gpio_0: pmx-gpio-0 {
+ marvell,pins = "mpp0";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_1: pmx-gpio-1 {
+ marvell,pins = "mpp1";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_2: pmx-gpio-2 {
+ marvell,pins = "mpp2";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_3: pmx-gpio-3 {
+ marvell,pins = "mpp3";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_4: pmx-gpio-4 {
+ marvell,pins = "mpp4";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_5: pmx-gpio-5 {
+ marvell,pins = "mpp5";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_6: pmx-gpio-6 {
+ marvell,pins = "mpp6";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_7: pmx-gpio-7 {
+ marvell,pins = "mpp7";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_8: pmx-gpio-8 {
+ marvell,pins = "mpp8";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_9: pmx-gpio-9 {
+ marvell,pins = "mpp9";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_10: pmx-gpio-10 {
+ marvell,pins = "mpp10";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_11: pmx-gpio-11 {
+ marvell,pins = "mpp11";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_12: pmx-gpio-12 {
+ marvell,pins = "mpp12";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_13: pmx-gpio-13 {
+ marvell,pins = "mpp13";
+ marvell,function = "gpio";
+ };
+
+ pmx_audio1_extclk: pmx-audio1-extclk {
+ marvell,pins = "mpp13";
+ marvell,function = "audio1";
+ };
+
+ pmx_gpio_14: pmx-gpio-14 {
+ marvell,pins = "mpp14";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_15: pmx-gpio-15 {
+ marvell,pins = "mpp15";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_16: pmx-gpio-16 {
+ marvell,pins = "mpp16";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_17: pmx-gpio-17 {
+ marvell,pins = "mpp17";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_18: pmx-gpio-18 {
+ marvell,pins = "mpp18";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_19: pmx-gpio-19 {
+ marvell,pins = "mpp19";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_20: pmx-gpio-20 {
+ marvell,pins = "mpp20";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_21: pmx-gpio-21 {
+ marvell,pins = "mpp21";
+ marvell,function = "gpio";
+ };
+
+ pmx_camera: pmx-camera {
+ marvell,pins = "mpp_camera";
+ marvell,function = "camera";
+ };
+
+ pmx_camera_gpio: pmx-camera-gpio {
+ marvell,pins = "mpp_camera";
+ marvell,function = "gpio";
+ };
+
+ pmx_sdio0: pmx-sdio0 {
+ marvell,pins = "mpp_sdio0";
+ marvell,function = "sdio0";
+ };
+
+ pmx_sdio0_gpio: pmx-sdio0-gpio {
+ marvell,pins = "mpp_sdio0";
+ marvell,function = "gpio";
+ };
+
+ pmx_sdio1: pmx-sdio1 {
+ marvell,pins = "mpp_sdio1";
+ marvell,function = "sdio1";
+ };
+
+ pmx_sdio1_gpio: pmx-sdio1-gpio {
+ marvell,pins = "mpp_sdio1";
+ marvell,function = "gpio";
+ };
+
+ pmx_audio1_gpio: pmx-audio1-gpio {
+ marvell,pins = "mpp_audio1";
+ marvell,function = "gpio";
+ };
+
+ pmx_audio1_i2s1_spdifo: pmx-audio1-i2s1-spdifo {
+ marvell,pins = "mpp_audio1";
+ marvell,function = "i2s1/spdifo";
+ };
+
+ pmx_spi0: pmx-spi0 {
+ marvell,pins = "mpp_spi0";
+ marvell,function = "spi0";
+ };
+
+ pmx_spi0_gpio: pmx-spi0-gpio {
+ marvell,pins = "mpp_spi0";
+ marvell,function = "gpio";
+ };
+
+ pmx_uart1: pmx-uart1 {
+ marvell,pins = "mpp_uart1";
+ marvell,function = "uart1";
+ };
+
+ pmx_uart1_gpio: pmx-uart1-gpio {
+ marvell,pins = "mpp_uart1";
+ marvell,function = "gpio";
+ };
+
+ pmx_nand: pmx-nand {
+ marvell,pins = "mpp_nand";
+ marvell,function = "nand";
+ };
+
+ pmx_nand_gpo: pmx-nand-gpo {
+ marvell,pins = "mpp_nand";
+ marvell,function = "gpo";
+ };
+ };
+
+ spi0: spi-ctrl@10600 {
+ compatible = "marvell,orion-spi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ interrupts = <6>;
+ reg = <0x10600 0x28>;
+ clocks = <&core_clk 0>;
+ pinctrl-0 = <&pmx_spi0>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ spi1: spi-ctrl@14600 {
+ compatible = "marvell,orion-spi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ interrupts = <5>;
+ reg = <0x14600 0x28>;
+ clocks = <&core_clk 0>;
+ status = "disabled";
+ };
+
+ i2c0: i2c-ctrl@11000 {
+ compatible = "marvell,mv64xxx-i2c";
+ reg = <0x11000 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <11>;
+ clock-frequency = <400000>;
+ timeout-ms = <1000>;
+ clocks = <&core_clk 0>;
+ status = "disabled";
+ };
+
+ ehci0: usb-host@50000 {
+ compatible = "marvell,orion-ehci";
+ reg = <0x50000 0x1000>;
+ interrupts = <24>;
+ clocks = <&gate_clk 0>;
+ status = "okay";
+ };
+
+ ehci1: usb-host@51000 {
+ compatible = "marvell,orion-ehci";
+ reg = <0x51000 0x1000>;
+ interrupts = <25>;
+ clocks = <&gate_clk 1>;
+ status = "okay";
+ };
+
+ sdio0: sdio-host@92000 {
+ compatible = "marvell,dove-sdhci";
+ reg = <0x92000 0x100>;
+ interrupts = <35>, <37>;
+ clocks = <&gate_clk 8>;
+ pinctrl-0 = <&pmx_sdio0>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ sdio1: sdio-host@90000 {
+ compatible = "marvell,dove-sdhci";
+ reg = <0x90000 0x100>;
+ interrupts = <36>, <38>;
+ clocks = <&gate_clk 9>;
+ pinctrl-0 = <&pmx_sdio1>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ sata0: sata-host@a0000 {
+ compatible = "marvell,orion-sata";
+ reg = <0xa0000 0x2400>;
+ interrupts = <62>;
+ clocks = <&gate_clk 3>;
+ nr-ports = <1>;
+ status = "disabled";
+ };
+
+ rtc: real-time-clock@d8500 {
+ compatible = "marvell,orion-rtc";
+ reg = <0xd8500 0x20>;
+ };
+
+ crypto: crypto-engine@30000 {
+ compatible = "marvell,orion-crypto";
+ reg = <0x30000 0x10000>,
+ <0xffffe000 0x800>;
+ reg-names = "regs", "sram";
+ interrupts = <31>;
+ clocks = <&gate_clk 15>;
+ status = "okay";
+ };
+
+ xor0: dma-engine@60800 {
+ compatible = "marvell,orion-xor";
+ reg = <0x60800 0x100
+ 0x60a00 0x100>;
+ clocks = <&gate_clk 23>;
+ status = "okay";
+
+ channel0 {
+ interrupts = <39>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+
+ channel1 {
+ interrupts = <40>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ };
+
+ xor1: dma-engine@60900 {
+ compatible = "marvell,orion-xor";
+ reg = <0x60900 0x100
+ 0x60b00 0x100>;
+ clocks = <&gate_clk 24>;
+ status = "okay";
+
+ channel0 {
+ interrupts = <42>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+
+ channel1 {
+ interrupts = <43>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ };
+
+ mdio: mdio-bus@72004 {
+ compatible = "marvell,orion-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x72004 0x84>;
+ interrupts = <30>;
+ clocks = <&gate_clk 2>;
+ status = "disabled";
+
+ ethphy: ethernet-phy {
+ device-type = "ethernet-phy";
+ /* set phy address in board file */
+ };
+ };
+
+ eth: ethernet-ctrl@72000 {
+ compatible = "marvell,orion-eth";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x72000 0x4000>;
+ clocks = <&gate_clk 2>;
+ marvell,tx-checksum-limit = <1600>;
+ status = "disabled";
+
+ ethernet-port@0 {
+ device_type = "network";
+ compatible = "marvell,orion-eth-port";
+ reg = <0>;
+ interrupts = <29>;
+ /* overwrite MAC address in bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ phy-handle = <ðphy>;
+ };
+ };
+
+ audio0: audio-controller@b0000 {
+ compatible = "marvell,dove-audio";
+ reg = <0xb0000 0x2210>;
+ interrupts = <19>, <20>;
+ clocks = <&gate_clk 12>;
+ clock-names = "internal";
+ status = "disabled";
+ };
+
+ audio1: audio-controller@b4000 {
+ compatible = "marvell,dove-audio";
+ reg = <0xb4000 0x2210>;
+ interrupts = <21>, <22>;
+ clocks = <&gate_clk 13>;
+ clock-names = "internal";
+ status = "disabled";
};
};
};
diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
new file mode 100644
index 0000000..5babba0
--- /dev/null
+++ b/arch/arm/boot/dts/dra7-evm.dts
@@ -0,0 +1,275 @@
+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "dra7.dtsi"
+
+/ {
+ model = "TI DRA7";
+ compatible = "ti,dra7-evm", "ti,dra752", "ti,dra7";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x60000000>; /* 1536 MB */
+ };
+
+ mmc2_3v3: fixedregulator-mmc2 {
+ compatible = "regulator-fixed";
+ regulator-name = "mmc2_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&dra7_pmx_core {
+ i2c1_pins: pinmux_i2c1_pins {
+ pinctrl-single,pins = <
+ 0x400 (PIN_INPUT | MUX_MODE0) /* i2c1_sda */
+ 0x404 (PIN_INPUT | MUX_MODE0) /* i2c1_scl */
+ >;
+ };
+
+ i2c2_pins: pinmux_i2c2_pins {
+ pinctrl-single,pins = <
+ 0x408 (PIN_INPUT | MUX_MODE0) /* i2c2_sda */
+ 0x40c (PIN_INPUT | MUX_MODE0) /* i2c2_scl */
+ >;
+ };
+
+ i2c3_pins: pinmux_i2c3_pins {
+ pinctrl-single,pins = <
+ 0x410 (PIN_INPUT | MUX_MODE0) /* i2c3_sda */
+ 0x414 (PIN_INPUT | MUX_MODE0) /* i2c3_scl */
+ >;
+ };
+
+ mcspi1_pins: pinmux_mcspi1_pins {
+ pinctrl-single,pins = <
+ 0x3a4 (PIN_INPUT | MUX_MODE0) /* spi2_clk */
+ 0x3a8 (PIN_INPUT | MUX_MODE0) /* spi2_d1 */
+ 0x3ac (PIN_INPUT | MUX_MODE0) /* spi2_d0 */
+ 0x3b0 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */
+ 0x3b4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs1 */
+ 0x3b8 (PIN_INPUT_SLEW | MUX_MODE6) /* spi2_cs2 */
+ 0x3bc (PIN_INPUT_SLEW | MUX_MODE6) /* spi2_cs3 */
+ >;
+ };
+
+ mcspi2_pins: pinmux_mcspi2_pins {
+ pinctrl-single,pins = <
+ 0x3c0 (PIN_INPUT | MUX_MODE0) /* spi2_sclk */
+ 0x3c4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */
+ 0x3c8 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */
+ 0x3cc (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */
+ >;
+ };
+
+ uart1_pins: pinmux_uart1_pins {
+ pinctrl-single,pins = <
+ 0x3e0 (PIN_INPUT_SLEW | MUX_MODE0) /* uart1_rxd */
+ 0x3e4 (PIN_INPUT_SLEW | MUX_MODE0) /* uart1_txd */
+ 0x3e8 (PIN_INPUT | MUX_MODE3) /* uart1_ctsn */
+ 0x3ec (PIN_INPUT | MUX_MODE3) /* uart1_rtsn */
+ >;
+ };
+
+ uart2_pins: pinmux_uart2_pins {
+ pinctrl-single,pins = <
+ 0x3f0 (PIN_INPUT | MUX_MODE0) /* uart2_rxd */
+ 0x3f4 (PIN_INPUT | MUX_MODE0) /* uart2_txd */
+ 0x3f8 (PIN_INPUT | MUX_MODE0) /* uart2_ctsn */
+ 0x3fc (PIN_INPUT | MUX_MODE0) /* uart2_rtsn */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ 0x248 (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd */
+ 0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd */
+ >;
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ clock-frequency = <400000>;
+
+ tps659038: tps659038@58 {
+ compatible = "ti,tps659038";
+ reg = <0x58>;
+
+ tps659038_pmic {
+ compatible = "ti,tps659038-pmic";
+
+ regulators {
+ smps123_reg: smps123 {
+ /* VDD_MPU */
+ regulator-name = "smps123";
+ regulator-min-microvolt = < 850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps45_reg: smps45 {
+ /* VDD_DSPEVE */
+ regulator-name = "smps45";
+ regulator-min-microvolt = < 850000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-boot-on;
+ };
+
+ smps6_reg: smps6 {
+ /* VDD_GPU - over VDD_SMPS6 */
+ regulator-name = "smps6";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <12500000>;
+ regulator-boot-on;
+ };
+
+ smps7_reg: smps7 {
+ /* CORE_VDD */
+ regulator-name = "smps7";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1030000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps8_reg: smps8 {
+ /* VDD_IVAHD */
+ regulator-name = "smps8";
+ regulator-min-microvolt = < 850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-boot-on;
+ };
+
+ smps9_reg: smps9 {
+ /* VDDS1V8 */
+ regulator-name = "smps9";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo1_reg: ldo1 {
+ /* LDO1_OUT --> SDIO */
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ ldo2_reg: ldo2 {
+ /* VDD_RTCIO */
+ /* LDO2 -> VDDSHV5, LDO2 also goes to CAN_PHY_3V3 */
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ ldo3_reg: ldo3 {
+ /* VDDA_1V8_PHY */
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+
+ ldo9_reg: ldo9 {
+ /* VDD_RTC */
+ regulator-name = "ldo9";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-boot-on;
+ };
+
+ ldoln_reg: ldoln {
+ /* VDDA_1V8_PLL */
+ regulator-name = "ldoln";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldousb_reg: ldousb {
+ /* VDDA_3V_USB: VDDA_USBHS33 */
+ regulator-name = "ldousb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ };
+ };
+ };
+};
+
+&i2c2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+ clock-frequency = <400000>;
+};
+
+&i2c3 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+ clock-frequency = <3400000>;
+};
+
+&mcspi1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcspi1_pins>;
+};
+
+&mcspi2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcspi2_pins>;
+};
+
+&uart1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+};
+
+&uart2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+};
+
+&mmc1 {
+ status = "okay";
+ vmmc-supply = <&ldo1_reg>;
+ bus-width = <4>;
+};
+
+&mmc2 {
+ status = "okay";
+ vmmc-supply = <&mmc2_3v3>;
+ bus-width = <8>;
+};
+
+&cpu0 {
+ cpu0-supply = <&smps123_reg>;
+};
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
new file mode 100644
index 0000000..d0df4c4
--- /dev/null
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -0,0 +1,586 @@
+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ * Based on "omap4.dtsi"
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/dra.h>
+
+#include "skeleton.dtsi"
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ compatible = "ti,dra7xx";
+ interrupt-parent = <&gic>;
+
+ aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ i2c3 = &i2c4;
+ i2c4 = &i2c5;
+ serial0 = &uart1;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ serial3 = &uart4;
+ serial4 = &uart5;
+ serial5 = &uart6;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <0>;
+
+ operating-points = <
+ /* kHz uV */
+ 1000000 1060000
+ 1176000 1160000
+ >;
+ };
+ cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <1>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ gic: interrupt-controller@48211000 {
+ compatible = "arm,cortex-a15-gic";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ reg = <0x48211000 0x1000>,
+ <0x48212000 0x1000>,
+ <0x48214000 0x2000>,
+ <0x48216000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ /*
+ * The soc node represents the soc top level view. It is uses for IPs
+ * that are not memory mapped in the MPU view or for the MPU itself.
+ */
+ soc {
+ compatible = "ti,omap-infra";
+ mpu {
+ compatible = "ti,omap5-mpu";
+ ti,hwmods = "mpu";
+ };
+ };
+
+ /*
+ * XXX: Use a flat representation of the SOC interconnect.
+ * The real OMAP interconnect network is quite complex.
+ * Since that will not bring real advantage to represent that in DT for
+ * the moment, just use a fake OCP bus entry to represent the whole bus
+ * hierarchy.
+ */
+ ocp {
+ compatible = "ti,omap4-l3-noc", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ ti,hwmods = "l3_main_1", "l3_main_2";
+ reg = <0x44000000 0x2000>,
+ <0x44800000 0x3000>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+
+ counter32k: counter@4ae04000 {
+ compatible = "ti,omap-counter32k";
+ reg = <0x4ae04000 0x40>;
+ ti,hwmods = "counter_32k";
+ };
+
+ dra7_pmx_core: pinmux@4a003400 {
+ compatible = "pinctrl-single";
+ reg = <0x4a003400 0x0464>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x3fffffff>;
+ };
+
+ sdma: dma-controller@4a056000 {
+ compatible = "ti,omap4430-sdma";
+ reg = <0x4a056000 0x1000>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ #dma-cells = <1>;
+ #dma-channels = <32>;
+ #dma-requests = <127>;
+ };
+
+ gpio1: gpio@4ae10000 {
+ compatible = "ti,omap4-gpio";
+ reg = <0x4ae10000 0x200>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "gpio1";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio2: gpio@48055000 {
+ compatible = "ti,omap4-gpio";
+ reg = <0x48055000 0x200>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "gpio2";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio3: gpio@48057000 {
+ compatible = "ti,omap4-gpio";
+ reg = <0x48057000 0x200>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "gpio3";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio4: gpio@48059000 {
+ compatible = "ti,omap4-gpio";
+ reg = <0x48059000 0x200>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "gpio4";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio5: gpio@4805b000 {
+ compatible = "ti,omap4-gpio";
+ reg = <0x4805b000 0x200>;
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "gpio5";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio6: gpio@4805d000 {
+ compatible = "ti,omap4-gpio";
+ reg = <0x4805d000 0x200>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "gpio6";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio7: gpio@48051000 {
+ compatible = "ti,omap4-gpio";
+ reg = <0x48051000 0x200>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "gpio7";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio8: gpio@48053000 {
+ compatible = "ti,omap4-gpio";
+ reg = <0x48053000 0x200>;
+ interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "gpio8";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ uart1: serial@4806a000 {
+ compatible = "ti,omap4-uart";
+ reg = <0x4806a000 0x100>;
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "uart1";
+ clock-frequency = <48000000>;
+ status = "disabled";
+ };
+
+ uart2: serial@4806c000 {
+ compatible = "ti,omap4-uart";
+ reg = <0x4806c000 0x100>;
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "uart2";
+ clock-frequency = <48000000>;
+ status = "disabled";
+ };
+
+ uart3: serial@48020000 {
+ compatible = "ti,omap4-uart";
+ reg = <0x48020000 0x100>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "uart3";
+ clock-frequency = <48000000>;
+ status = "disabled";
+ };
+
+ uart4: serial@4806e000 {
+ compatible = "ti,omap4-uart";
+ reg = <0x4806e000 0x100>;
+ interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "uart4";
+ clock-frequency = <48000000>;
+ status = "disabled";
+ };
+
+ uart5: serial@48066000 {
+ compatible = "ti,omap4-uart";
+ reg = <0x48066000 0x100>;
+ interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "uart5";
+ clock-frequency = <48000000>;
+ status = "disabled";
+ };
+
+ uart6: serial@48068000 {
+ compatible = "ti,omap4-uart";
+ reg = <0x48068000 0x100>;
+ interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "uart6";
+ clock-frequency = <48000000>;
+ status = "disabled";
+ };
+
+ uart7: serial@48420000 {
+ compatible = "ti,omap4-uart";
+ reg = <0x48420000 0x100>;
+ ti,hwmods = "uart7";
+ clock-frequency = <48000000>;
+ status = "disabled";
+ };
+
+ uart8: serial@48422000 {
+ compatible = "ti,omap4-uart";
+ reg = <0x48422000 0x100>;
+ ti,hwmods = "uart8";
+ clock-frequency = <48000000>;
+ status = "disabled";
+ };
+
+ uart9: serial@48424000 {
+ compatible = "ti,omap4-uart";
+ reg = <0x48424000 0x100>;
+ ti,hwmods = "uart9";
+ clock-frequency = <48000000>;
+ status = "disabled";
+ };
+
+ uart10: serial@4ae2b000 {
+ compatible = "ti,omap4-uart";
+ reg = <0x4ae2b000 0x100>;
+ ti,hwmods = "uart10";
+ clock-frequency = <48000000>;
+ status = "disabled";
+ };
+
+ timer1: timer@4ae18000 {
+ compatible = "ti,omap5430-timer";
+ reg = <0x4ae18000 0x80>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "timer1";
+ ti,timer-alwon;
+ };
+
+ timer2: timer@48032000 {
+ compatible = "ti,omap5430-timer";
+ reg = <0x48032000 0x80>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "timer2";
+ };
+
+ timer3: timer@48034000 {
+ compatible = "ti,omap5430-timer";
+ reg = <0x48034000 0x80>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "timer3";
+ };
+
+ timer4: timer@48036000 {
+ compatible = "ti,omap5430-timer";
+ reg = <0x48036000 0x80>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "timer4";
+ };
+
+ timer5: timer@48820000 {
+ compatible = "ti,omap5430-timer";
+ reg = <0x48820000 0x80>;
+ interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "timer5";
+ ti,timer-dsp;
+ };
+
+ timer6: timer@48822000 {
+ compatible = "ti,omap5430-timer";
+ reg = <0x48822000 0x80>;
+ interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "timer6";
+ ti,timer-dsp;
+ ti,timer-pwm;
+ };
+
+ timer7: timer@48824000 {
+ compatible = "ti,omap5430-timer";
+ reg = <0x48824000 0x80>;
+ interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "timer7";
+ ti,timer-dsp;
+ };
+
+ timer8: timer@48826000 {
+ compatible = "ti,omap5430-timer";
+ reg = <0x48826000 0x80>;
+ interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "timer8";
+ ti,timer-dsp;
+ ti,timer-pwm;
+ };
+
+ timer9: timer@4803e000 {
+ compatible = "ti,omap5430-timer";
+ reg = <0x4803e000 0x80>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "timer9";
+ };
+
+ timer10: timer@48086000 {
+ compatible = "ti,omap5430-timer";
+ reg = <0x48086000 0x80>;
+ interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "timer10";
+ };
+
+ timer11: timer@48088000 {
+ compatible = "ti,omap5430-timer";
+ reg = <0x48088000 0x80>;
+ interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "timer11";
+ ti,timer-pwm;
+ };
+
+ timer13: timer@48828000 {
+ compatible = "ti,omap5430-timer";
+ reg = <0x48828000 0x80>;
+ ti,hwmods = "timer13";
+ status = "disabled";
+ };
+
+ timer14: timer@4882a000 {
+ compatible = "ti,omap5430-timer";
+ reg = <0x4882a000 0x80>;
+ ti,hwmods = "timer14";
+ status = "disabled";
+ };
+
+ timer15: timer@4882c000 {
+ compatible = "ti,omap5430-timer";
+ reg = <0x4882c000 0x80>;
+ ti,hwmods = "timer15";
+ status = "disabled";
+ };
+
+ timer16: timer@4882e000 {
+ compatible = "ti,omap5430-timer";
+ reg = <0x4882e000 0x80>;
+ ti,hwmods = "timer16";
+ status = "disabled";
+ };
+
+ wdt2: wdt@4ae14000 {
+ compatible = "ti,omap4-wdt";
+ reg = <0x4ae14000 0x80>;
+ interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "wd_timer2";
+ };
+
+ i2c1: i2c@48070000 {
+ compatible = "ti,omap4-i2c";
+ reg = <0x48070000 0x100>;
+ interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "i2c1";
+ status = "disabled";
+ };
+
+ i2c2: i2c@48072000 {
+ compatible = "ti,omap4-i2c";
+ reg = <0x48072000 0x100>;
+ interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "i2c2";
+ status = "disabled";
+ };
+
+ i2c3: i2c@48060000 {
+ compatible = "ti,omap4-i2c";
+ reg = <0x48060000 0x100>;
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "i2c3";
+ status = "disabled";
+ };
+
+ i2c4: i2c@4807a000 {
+ compatible = "ti,omap4-i2c";
+ reg = <0x4807a000 0x100>;
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "i2c4";
+ status = "disabled";
+ };
+
+ i2c5: i2c@4807c000 {
+ compatible = "ti,omap4-i2c";
+ reg = <0x4807c000 0x100>;
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "i2c5";
+ status = "disabled";
+ };
+
+ mmc1: mmc@4809c000 {
+ compatible = "ti,omap4-hsmmc";
+ reg = <0x4809c000 0x400>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "mmc1";
+ ti,dual-volt;
+ ti,needs-special-reset;
+ dmas = <&sdma 61>, <&sdma 62>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ mmc2: mmc@480b4000 {
+ compatible = "ti,omap4-hsmmc";
+ reg = <0x480b4000 0x400>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "mmc2";
+ ti,needs-special-reset;
+ dmas = <&sdma 47>, <&sdma 48>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ mmc3: mmc@480ad000 {
+ compatible = "ti,omap4-hsmmc";
+ reg = <0x480ad000 0x400>;
+ interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "mmc3";
+ ti,needs-special-reset;
+ dmas = <&sdma 77>, <&sdma 78>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ mmc4: mmc@480d1000 {
+ compatible = "ti,omap4-hsmmc";
+ reg = <0x480d1000 0x400>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "mmc4";
+ ti,needs-special-reset;
+ dmas = <&sdma 57>, <&sdma 58>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ mcspi1: spi@48098000 {
+ compatible = "ti,omap4-mcspi";
+ reg = <0x48098000 0x200>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "mcspi1";
+ ti,spi-num-cs = <4>;
+ dmas = <&sdma 35>,
+ <&sdma 36>,
+ <&sdma 37>,
+ <&sdma 38>,
+ <&sdma 39>,
+ <&sdma 40>,
+ <&sdma 41>,
+ <&sdma 42>;
+ dma-names = "tx0", "rx0", "tx1", "rx1",
+ "tx2", "rx2", "tx3", "rx3";
+ status = "disabled";
+ };
+
+ mcspi2: spi@4809a000 {
+ compatible = "ti,omap4-mcspi";
+ reg = <0x4809a000 0x200>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "mcspi2";
+ ti,spi-num-cs = <2>;
+ dmas = <&sdma 43>,
+ <&sdma 44>,
+ <&sdma 45>,
+ <&sdma 46>;
+ dma-names = "tx0", "rx0", "tx1", "rx1";
+ status = "disabled";
+ };
+
+ mcspi3: spi@480b8000 {
+ compatible = "ti,omap4-mcspi";
+ reg = <0x480b8000 0x200>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "mcspi3";
+ ti,spi-num-cs = <2>;
+ dmas = <&sdma 15>, <&sdma 16>;
+ dma-names = "tx0", "rx0";
+ status = "disabled";
+ };
+
+ mcspi4: spi@480ba000 {
+ compatible = "ti,omap4-mcspi";
+ reg = <0x480ba000 0x200>;
+ interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "mcspi4";
+ ti,spi-num-cs = <1>;
+ dmas = <&sdma 70>, <&sdma 71>;
+ dma-names = "tx0", "rx0";
+ status = "disabled";
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/exynos4.dtsi
index caadc02..a73eeb5 100644
--- a/arch/arm/boot/dts/exynos4.dtsi
+++ b/arch/arm/boot/dts/exynos4.dtsi
@@ -49,6 +49,12 @@
reg = <0x10000000 0x100>;
};
+ mipi_phy: video-phy@10020710 {
+ compatible = "samsung,s5pv210-mipi-video-phy";
+ reg = <0x10020710 8>;
+ #phy-cells = <1>;
+ };
+
pd_mfc: mfc-power-domain@10023C40 {
compatible = "samsung,exynos4210-pd";
reg = <0x10023C40 0x20>;
@@ -161,6 +167,8 @@
clock-names = "csis", "sclk_csis";
bus-width = <4>;
samsung,power-domain = <&pd_cam>;
+ phys = <&mipi_phy 0>;
+ phy-names = "csis";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
@@ -174,6 +182,8 @@
clock-names = "csis", "sclk_csis";
bus-width = <2>;
samsung,power-domain = <&pd_cam>;
+ phys = <&mipi_phy 2>;
+ phy-names = "csis";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/exynos4210-origen.dts
index 382d8c7..d3340db 100644
--- a/arch/arm/boot/dts/exynos4210-origen.dts
+++ b/arch/arm/boot/dts/exynos4210-origen.dts
@@ -32,13 +32,20 @@
bootargs ="root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC2,115200 init=/linuxrc";
};
- mmc_reg: voltage-regulator {
- compatible = "regulator-fixed";
- regulator-name = "VMEM_VDD_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- gpio = <&gpx1 1 0>;
- enable-active-high;
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mmc_reg: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "VMEM_VDD_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ gpio = <&gpx1 1 0>;
+ enable-active-high;
+ };
};
tmu@100C0000 {
diff --git a/arch/arm/boot/dts/exynos4412-origen.dts b/arch/arm/boot/dts/exynos4412-origen.dts
index 8768b03..d65984c 100644
--- a/arch/arm/boot/dts/exynos4412-origen.dts
+++ b/arch/arm/boot/dts/exynos4412-origen.dts
@@ -32,13 +32,20 @@
reg = <0x0203F000 0x1000>;
};
- mmc_reg: voltage-regulator {
- compatible = "regulator-fixed";
- regulator-name = "VMEM_VDD_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- gpio = <&gpx1 1 0>;
- enable-active-high;
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mmc_reg: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "VMEM_VDD_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ gpio = <&gpx1 1 0>;
+ enable-active-high;
+ };
};
pinctrl@11000000 {
diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
index cee55fa..6845270 100644
--- a/arch/arm/boot/dts/exynos5250-arndale.dts
+++ b/arch/arm/boot/dts/exynos5250-arndale.dts
@@ -324,7 +324,14 @@
};
i2c@12C80000 {
- status = "disabled";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+ samsung,i2c-slave-addr = <0x50>;
+
+ hdmiddc@50 {
+ compatible = "samsung,exynos4210-hdmiddc";
+ reg = <0x50>;
+ };
};
i2c@12C90000 {
@@ -362,6 +369,17 @@
status = "disabled";
};
+ i2c@12CE0000 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+ samsung,i2c-slave-addr = <0x38>;
+
+ hdmiphy@38 {
+ compatible = "samsung,exynos4212-hdmiphy";
+ reg = <0x38>;
+ };
+ };
+
i2c@121D0000 {
status = "disabled";
};
@@ -412,6 +430,10 @@
status = "disabled";
};
+ i2s0: i2s@03830000 {
+ status = "okay";
+ };
+
spi_0: spi@12d20000 {
status = "disabled";
};
@@ -482,13 +504,15 @@
#address-cells = <1>;
#size-cells = <0>;
- main_dc_reg: fixedregulator@1 {
+ main_dc_reg: regulator@0 {
compatible = "regulator-fixed";
+ reg = <0>;
regulator-name = "MAIN_DC";
};
- mmc_reg: voltage-regulator {
+ mmc_reg: regulator@1 {
compatible = "regulator-fixed";
+ reg = <1>;
regulator-name = "VDD_33ON_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
@@ -496,8 +520,9 @@
enable-active-high;
};
- reg_hdmi_en: fixedregulator@0 {
+ reg_hdmi_en: regulator@2 {
compatible = "regulator-fixed";
+ reg = <2>;
regulator-name = "hdmi-en";
};
};
diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/exynos5250-smdk5250.dts
index 2538b32..f86d567 100644
--- a/arch/arm/boot/dts/exynos5250-smdk5250.dts
+++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts
@@ -231,14 +231,6 @@
status = "okay";
};
- i2s1: i2s@12D60000 {
- status = "disabled";
- };
-
- i2s2: i2s@12D70000 {
- status = "disabled";
- };
-
sound {
compatible = "samsung,smdk-wm8994";
diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi
index 7d7cc77..9db5047 100644
--- a/arch/arm/boot/dts/exynos5250.dtsi
+++ b/arch/arm/boot/dts/exynos5250.dtsi
@@ -96,6 +96,11 @@
<1 14 0xf08>,
<1 11 0xf08>,
<1 10 0xf08>;
+ /* Unfortunately we need this since some versions of U-Boot
+ * on Exynos don't set the CNTFRQ register, so we need the
+ * value from DT.
+ */
+ clock-frequency = <24000000>;
};
mct@101C0000 {
@@ -417,6 +422,7 @@
i2s0: i2s@03830000 {
compatible = "samsung,s5pv210-i2s";
+ status = "disabled";
reg = <0x03830000 0x100>;
dmas = <&pdma0 10
&pdma0 9
@@ -433,6 +439,7 @@
i2s1: i2s@12D60000 {
compatible = "samsung,s3c6410-i2s";
+ status = "disabled";
reg = <0x12D60000 0x100>;
dmas = <&pdma1 12
&pdma1 11>;
@@ -445,6 +452,7 @@
i2s2: i2s@12D70000 {
compatible = "samsung,s3c6410-i2s";
+ status = "disabled";
reg = <0x12D70000 0x100>;
dmas = <&pdma0 12
&pdma0 11>;
@@ -610,16 +618,18 @@
compatible = "samsung,exynos4212-hdmi";
reg = <0x14530000 0x70000>;
interrupts = <0 95 0>;
- clocks = <&clock 333>, <&clock 136>, <&clock 137>,
- <&clock 333>, <&clock 333>;
+ clocks = <&clock 344>, <&clock 136>, <&clock 137>,
+ <&clock 159>, <&clock 1024>;
clock-names = "hdmi", "sclk_hdmi", "sclk_pixel",
- "sclk_hdmiphy", "hdmiphy";
+ "sclk_hdmiphy", "mout_hdmi";
};
mixer {
compatible = "samsung,exynos5250-mixer";
reg = <0x14450000 0x10000>;
interrupts = <0 94 0>;
+ clocks = <&clock 343>, <&clock 136>;
+ clock-names = "mixer", "sclk_hdmi";
};
dp_phy: video-phy@10040720 {
diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts
index bafba25..79524c7 100644
--- a/arch/arm/boot/dts/exynos5420-smdk5420.dts
+++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts
@@ -61,4 +61,30 @@
};
};
+ pinctrl@13400000 {
+ hdmi_hpd_irq: hdmi-hpd-irq {
+ samsung,pins = "gpx3-7";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+ };
+
+ hdmi@14530000 {
+ status = "okay";
+ hpd-gpio = <&gpx3 7 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_hpd_irq>;
+ };
+
+ i2c_2: i2c@12C80000 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+ status = "okay";
+
+ hdmiddc@50 {
+ compatible = "samsung,exynos4210-hdmiddc";
+ reg = <0x50>;
+ };
+ };
};
diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi
index d537cd7..09aa06c 100644
--- a/arch/arm/boot/dts/exynos5420.dtsi
+++ b/arch/arm/boot/dts/exynos5420.dtsi
@@ -27,6 +27,10 @@
pinctrl2 = &pinctrl_2;
pinctrl3 = &pinctrl_3;
pinctrl4 = &pinctrl_4;
+ i2c0 = &i2c_0;
+ i2c1 = &i2c_1;
+ i2c2 = &i2c_2;
+ i2c3 = &i2c_3;
};
cpus {
@@ -235,4 +239,75 @@
io-channel-ranges;
status = "disabled";
};
+
+ i2c_0: i2c@12C60000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12C60000 0x100>;
+ interrupts = <0 56 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clock 261>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_bus>;
+ status = "disabled";
+ };
+
+ i2c_1: i2c@12C70000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12C70000 0x100>;
+ interrupts = <0 57 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clock 262>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_bus>;
+ status = "disabled";
+ };
+
+ i2c_2: i2c@12C80000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12C80000 0x100>;
+ interrupts = <0 58 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clock 263>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_bus>;
+ status = "disabled";
+ };
+
+ i2c_3: i2c@12C90000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12C90000 0x100>;
+ interrupts = <0 59 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clock 264>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_bus>;
+ status = "disabled";
+ };
+
+ hdmi@14530000 {
+ compatible = "samsung,exynos4212-hdmi";
+ reg = <0x14530000 0x70000>;
+ interrupts = <0 95 0>;
+ clocks = <&clock 413>, <&clock 143>, <&clock 768>,
+ <&clock 158>, <&clock 640>;
+ clock-names = "hdmi", "sclk_hdmi", "sclk_pixel",
+ "sclk_hdmiphy", "mout_hdmi";
+ status = "disabled";
+ };
+
+ mixer@14450000 {
+ compatible = "samsung,exynos5420-mixer";
+ reg = <0x14450000 0x10000>;
+ interrupts = <0 94 0>;
+ clocks = <&clock 431>, <&clock 143>;
+ clock-names = "mixer", "sclk_hdmi";
+ };
};
diff --git a/arch/arm/boot/dts/imx23-evk.dts b/arch/arm/boot/dts/imx23-evk.dts
index 185c7c01..1f026ad 100644
--- a/arch/arm/boot/dts/imx23-evk.dts
+++ b/arch/arm/boot/dts/imx23-evk.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx23.dtsi"
+#include "imx23.dtsi"
/ {
model = "Freescale i.MX23 Evaluation Kit";
@@ -45,14 +45,14 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1123 /* MX23_PAD_LCD_RESET__GPIO_1_18 */
- 0x11d3 /* MX23_PAD_PWM3__GPIO_1_29 */
- 0x11e3 /* MX23_PAD_PWM4__GPIO_1_30 */
- 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */
+ MX23_PAD_LCD_RESET__GPIO_1_18
+ MX23_PAD_PWM3__GPIO_1_29
+ MX23_PAD_PWM4__GPIO_1_30
+ MX23_PAD_SSP1_DETECT__SSP1_DETECT
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx23-olinuxino.dts b/arch/arm/boot/dts/imx23-olinuxino.dts
index fc766ae..526bfdb 100644
--- a/arch/arm/boot/dts/imx23-olinuxino.dts
+++ b/arch/arm/boot/dts/imx23-olinuxino.dts
@@ -12,7 +12,7 @@
*/
/dts-v1/;
-/include/ "imx23.dtsi"
+#include "imx23.dtsi"
/ {
model = "i.MX23 Olinuxino Low Cost Board";
@@ -40,21 +40,21 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0113 /* MX23_PAD_GPMI_ALE__GPIO_0_17 */
+ MX23_PAD_GPMI_ALE__GPIO_0_17
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
led_pin_gpio2_1: led_gpio2_1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2013 /* MX23_PAD_SSP1_DETECT__GPIO_2_1 */
+ MX23_PAD_SSP1_DETECT__GPIO_2_1
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx23-pinfunc.h b/arch/arm/boot/dts/imx23-pinfunc.h
new file mode 100644
index 0000000..5c0f32ca
--- /dev/null
+++ b/arch/arm/boot/dts/imx23-pinfunc.h
@@ -0,0 +1,333 @@
+/*
+ * Header providing constants for i.MX23 pinctrl bindings.
+ *
+ * Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#ifndef __DT_BINDINGS_MX23_PINCTRL_H__
+#define __DT_BINDINGS_MX23_PINCTRL_H__
+
+#include "mxs-pinfunc.h"
+
+#define MX23_PAD_GPMI_D00__GPMI_D00 0x0000
+#define MX23_PAD_GPMI_D01__GPMI_D01 0x0010
+#define MX23_PAD_GPMI_D02__GPMI_D02 0x0020
+#define MX23_PAD_GPMI_D03__GPMI_D03 0x0030
+#define MX23_PAD_GPMI_D04__GPMI_D04 0x0040
+#define MX23_PAD_GPMI_D05__GPMI_D05 0x0050
+#define MX23_PAD_GPMI_D06__GPMI_D06 0x0060
+#define MX23_PAD_GPMI_D07__GPMI_D07 0x0070
+#define MX23_PAD_GPMI_D08__GPMI_D08 0x0080
+#define MX23_PAD_GPMI_D09__GPMI_D09 0x0090
+#define MX23_PAD_GPMI_D10__GPMI_D10 0x00a0
+#define MX23_PAD_GPMI_D11__GPMI_D11 0x00b0
+#define MX23_PAD_GPMI_D12__GPMI_D12 0x00c0
+#define MX23_PAD_GPMI_D13__GPMI_D13 0x00d0
+#define MX23_PAD_GPMI_D14__GPMI_D14 0x00e0
+#define MX23_PAD_GPMI_D15__GPMI_D15 0x00f0
+#define MX23_PAD_GPMI_CLE__GPMI_CLE 0x0100
+#define MX23_PAD_GPMI_ALE__GPMI_ALE 0x0110
+#define MX23_PAD_GPMI_CE2N__GPMI_CE2N 0x0120
+#define MX23_PAD_GPMI_RDY0__GPMI_RDY0 0x0130
+#define MX23_PAD_GPMI_RDY1__GPMI_RDY1 0x0140
+#define MX23_PAD_GPMI_RDY2__GPMI_RDY2 0x0150
+#define MX23_PAD_GPMI_RDY3__GPMI_RDY3 0x0160
+#define MX23_PAD_GPMI_WPN__GPMI_WPN 0x0170
+#define MX23_PAD_GPMI_WRN__GPMI_WRN 0x0180
+#define MX23_PAD_GPMI_RDN__GPMI_RDN 0x0190
+#define MX23_PAD_AUART1_CTS__AUART1_CTS 0x01a0
+#define MX23_PAD_AUART1_RTS__AUART1_RTS 0x01b0
+#define MX23_PAD_AUART1_RX__AUART1_RX 0x01c0
+#define MX23_PAD_AUART1_TX__AUART1_TX 0x01d0
+#define MX23_PAD_I2C_SCL__I2C_SCL 0x01e0
+#define MX23_PAD_I2C_SDA__I2C_SDA 0x01f0
+#define MX23_PAD_LCD_D00__LCD_D00 0x1000
+#define MX23_PAD_LCD_D01__LCD_D01 0x1010
+#define MX23_PAD_LCD_D02__LCD_D02 0x1020
+#define MX23_PAD_LCD_D03__LCD_D03 0x1030
+#define MX23_PAD_LCD_D04__LCD_D04 0x1040
+#define MX23_PAD_LCD_D05__LCD_D05 0x1050
+#define MX23_PAD_LCD_D06__LCD_D06 0x1060
+#define MX23_PAD_LCD_D07__LCD_D07 0x1070
+#define MX23_PAD_LCD_D08__LCD_D08 0x1080
+#define MX23_PAD_LCD_D09__LCD_D09 0x1090
+#define MX23_PAD_LCD_D10__LCD_D10 0x10a0
+#define MX23_PAD_LCD_D11__LCD_D11 0x10b0
+#define MX23_PAD_LCD_D12__LCD_D12 0x10c0
+#define MX23_PAD_LCD_D13__LCD_D13 0x10d0
+#define MX23_PAD_LCD_D14__LCD_D14 0x10e0
+#define MX23_PAD_LCD_D15__LCD_D15 0x10f0
+#define MX23_PAD_LCD_D16__LCD_D16 0x1100
+#define MX23_PAD_LCD_D17__LCD_D17 0x1110
+#define MX23_PAD_LCD_RESET__LCD_RESET 0x1120
+#define MX23_PAD_LCD_RS__LCD_RS 0x1130
+#define MX23_PAD_LCD_WR__LCD_WR 0x1140
+#define MX23_PAD_LCD_CS__LCD_CS 0x1150
+#define MX23_PAD_LCD_DOTCK__LCD_DOTCK 0x1160
+#define MX23_PAD_LCD_ENABLE__LCD_ENABLE 0x1170
+#define MX23_PAD_LCD_HSYNC__LCD_HSYNC 0x1180
+#define MX23_PAD_LCD_VSYNC__LCD_VSYNC 0x1190
+#define MX23_PAD_PWM0__PWM0 0x11a0
+#define MX23_PAD_PWM1__PWM1 0x11b0
+#define MX23_PAD_PWM2__PWM2 0x11c0
+#define MX23_PAD_PWM3__PWM3 0x11d0
+#define MX23_PAD_PWM4__PWM4 0x11e0
+#define MX23_PAD_SSP1_CMD__SSP1_CMD 0x2000
+#define MX23_PAD_SSP1_DETECT__SSP1_DETECT 0x2010
+#define MX23_PAD_SSP1_DATA0__SSP1_DATA0 0x2020
+#define MX23_PAD_SSP1_DATA1__SSP1_DATA1 0x2030
+#define MX23_PAD_SSP1_DATA2__SSP1_DATA2 0x2040
+#define MX23_PAD_SSP1_DATA3__SSP1_DATA3 0x2050
+#define MX23_PAD_SSP1_SCK__SSP1_SCK 0x2060
+#define MX23_PAD_ROTARYA__ROTARYA 0x2070
+#define MX23_PAD_ROTARYB__ROTARYB 0x2080
+#define MX23_PAD_EMI_A00__EMI_A00 0x2090
+#define MX23_PAD_EMI_A01__EMI_A01 0x20a0
+#define MX23_PAD_EMI_A02__EMI_A02 0x20b0
+#define MX23_PAD_EMI_A03__EMI_A03 0x20c0
+#define MX23_PAD_EMI_A04__EMI_A04 0x20d0
+#define MX23_PAD_EMI_A05__EMI_A05 0x20e0
+#define MX23_PAD_EMI_A06__EMI_A06 0x20f0
+#define MX23_PAD_EMI_A07__EMI_A07 0x2100
+#define MX23_PAD_EMI_A08__EMI_A08 0x2110
+#define MX23_PAD_EMI_A09__EMI_A09 0x2120
+#define MX23_PAD_EMI_A10__EMI_A10 0x2130
+#define MX23_PAD_EMI_A11__EMI_A11 0x2140
+#define MX23_PAD_EMI_A12__EMI_A12 0x2150
+#define MX23_PAD_EMI_BA0__EMI_BA0 0x2160
+#define MX23_PAD_EMI_BA1__EMI_BA1 0x2170
+#define MX23_PAD_EMI_CASN__EMI_CASN 0x2180
+#define MX23_PAD_EMI_CE0N__EMI_CE0N 0x2190
+#define MX23_PAD_EMI_CE1N__EMI_CE1N 0x21a0
+#define MX23_PAD_GPMI_CE1N__GPMI_CE1N 0x21b0
+#define MX23_PAD_GPMI_CE0N__GPMI_CE0N 0x21c0
+#define MX23_PAD_EMI_CKE__EMI_CKE 0x21d0
+#define MX23_PAD_EMI_RASN__EMI_RASN 0x21e0
+#define MX23_PAD_EMI_WEN__EMI_WEN 0x21f0
+#define MX23_PAD_EMI_D00__EMI_D00 0x3000
+#define MX23_PAD_EMI_D01__EMI_D01 0x3010
+#define MX23_PAD_EMI_D02__EMI_D02 0x3020
+#define MX23_PAD_EMI_D03__EMI_D03 0x3030
+#define MX23_PAD_EMI_D04__EMI_D04 0x3040
+#define MX23_PAD_EMI_D05__EMI_D05 0x3050
+#define MX23_PAD_EMI_D06__EMI_D06 0x3060
+#define MX23_PAD_EMI_D07__EMI_D07 0x3070
+#define MX23_PAD_EMI_D08__EMI_D08 0x3080
+#define MX23_PAD_EMI_D09__EMI_D09 0x3090
+#define MX23_PAD_EMI_D10__EMI_D10 0x30a0
+#define MX23_PAD_EMI_D11__EMI_D11 0x30b0
+#define MX23_PAD_EMI_D12__EMI_D12 0x30c0
+#define MX23_PAD_EMI_D13__EMI_D13 0x30d0
+#define MX23_PAD_EMI_D14__EMI_D14 0x30e0
+#define MX23_PAD_EMI_D15__EMI_D15 0x30f0
+#define MX23_PAD_EMI_DQM0__EMI_DQM0 0x3100
+#define MX23_PAD_EMI_DQM1__EMI_DQM1 0x3110
+#define MX23_PAD_EMI_DQS0__EMI_DQS0 0x3120
+#define MX23_PAD_EMI_DQS1__EMI_DQS1 0x3130
+#define MX23_PAD_EMI_CLK__EMI_CLK 0x3140
+#define MX23_PAD_EMI_CLKN__EMI_CLKN 0x3150
+#define MX23_PAD_GPMI_D00__LCD_D8 0x0001
+#define MX23_PAD_GPMI_D01__LCD_D9 0x0011
+#define MX23_PAD_GPMI_D02__LCD_D10 0x0021
+#define MX23_PAD_GPMI_D03__LCD_D11 0x0031
+#define MX23_PAD_GPMI_D04__LCD_D12 0x0041
+#define MX23_PAD_GPMI_D05__LCD_D13 0x0051
+#define MX23_PAD_GPMI_D06__LCD_D14 0x0061
+#define MX23_PAD_GPMI_D07__LCD_D15 0x0071
+#define MX23_PAD_GPMI_D08__LCD_D18 0x0081
+#define MX23_PAD_GPMI_D09__LCD_D19 0x0091
+#define MX23_PAD_GPMI_D10__LCD_D20 0x00a1
+#define MX23_PAD_GPMI_D11__LCD_D21 0x00b1
+#define MX23_PAD_GPMI_D12__LCD_D22 0x00c1
+#define MX23_PAD_GPMI_D13__LCD_D23 0x00d1
+#define MX23_PAD_GPMI_D14__AUART2_RX 0x00e1
+#define MX23_PAD_GPMI_D15__AUART2_TX 0x00f1
+#define MX23_PAD_GPMI_CLE__LCD_D16 0x0101
+#define MX23_PAD_GPMI_ALE__LCD_D17 0x0111
+#define MX23_PAD_GPMI_CE2N__ATA_A2 0x0121
+#define MX23_PAD_AUART1_RTS__IR_CLK 0x01b1
+#define MX23_PAD_AUART1_RX__IR_RX 0x01c1
+#define MX23_PAD_AUART1_TX__IR_TX 0x01d1
+#define MX23_PAD_I2C_SCL__GPMI_RDY2 0x01e1
+#define MX23_PAD_I2C_SDA__GPMI_CE2N 0x01f1
+#define MX23_PAD_LCD_D00__ETM_DA8 0x1001
+#define MX23_PAD_LCD_D01__ETM_DA9 0x1011
+#define MX23_PAD_LCD_D02__ETM_DA10 0x1021
+#define MX23_PAD_LCD_D03__ETM_DA11 0x1031
+#define MX23_PAD_LCD_D04__ETM_DA12 0x1041
+#define MX23_PAD_LCD_D05__ETM_DA13 0x1051
+#define MX23_PAD_LCD_D06__ETM_DA14 0x1061
+#define MX23_PAD_LCD_D07__ETM_DA15 0x1071
+#define MX23_PAD_LCD_D08__ETM_DA0 0x1081
+#define MX23_PAD_LCD_D09__ETM_DA1 0x1091
+#define MX23_PAD_LCD_D10__ETM_DA2 0x10a1
+#define MX23_PAD_LCD_D11__ETM_DA3 0x10b1
+#define MX23_PAD_LCD_D12__ETM_DA4 0x10c1
+#define MX23_PAD_LCD_D13__ETM_DA5 0x10d1
+#define MX23_PAD_LCD_D14__ETM_DA6 0x10e1
+#define MX23_PAD_LCD_D15__ETM_DA7 0x10f1
+#define MX23_PAD_LCD_RESET__ETM_TCTL 0x1121
+#define MX23_PAD_LCD_RS__ETM_TCLK 0x1131
+#define MX23_PAD_LCD_DOTCK__GPMI_RDY3 0x1161
+#define MX23_PAD_LCD_ENABLE__I2C_SCL 0x1171
+#define MX23_PAD_LCD_HSYNC__I2C_SDA 0x1181
+#define MX23_PAD_LCD_VSYNC__LCD_BUSY 0x1191
+#define MX23_PAD_PWM0__ROTARYA 0x11a1
+#define MX23_PAD_PWM1__ROTARYB 0x11b1
+#define MX23_PAD_PWM2__GPMI_RDY3 0x11c1
+#define MX23_PAD_PWM3__ETM_TCTL 0x11d1
+#define MX23_PAD_PWM4__ETM_TCLK 0x11e1
+#define MX23_PAD_SSP1_DETECT__GPMI_CE3N 0x2011
+#define MX23_PAD_SSP1_DATA1__I2C_SCL 0x2031
+#define MX23_PAD_SSP1_DATA2__I2C_SDA 0x2041
+#define MX23_PAD_ROTARYA__AUART2_RTS 0x2071
+#define MX23_PAD_ROTARYB__AUART2_CTS 0x2081
+#define MX23_PAD_GPMI_D00__SSP2_DATA0 0x0002
+#define MX23_PAD_GPMI_D01__SSP2_DATA1 0x0012
+#define MX23_PAD_GPMI_D02__SSP2_DATA2 0x0022
+#define MX23_PAD_GPMI_D03__SSP2_DATA3 0x0032
+#define MX23_PAD_GPMI_D04__SSP2_DATA4 0x0042
+#define MX23_PAD_GPMI_D05__SSP2_DATA5 0x0052
+#define MX23_PAD_GPMI_D06__SSP2_DATA6 0x0062
+#define MX23_PAD_GPMI_D07__SSP2_DATA7 0x0072
+#define MX23_PAD_GPMI_D08__SSP1_DATA4 0x0082
+#define MX23_PAD_GPMI_D09__SSP1_DATA5 0x0092
+#define MX23_PAD_GPMI_D10__SSP1_DATA6 0x00a2
+#define MX23_PAD_GPMI_D11__SSP1_DATA7 0x00b2
+#define MX23_PAD_GPMI_D15__GPMI_CE3N 0x00f2
+#define MX23_PAD_GPMI_RDY0__SSP2_DETECT 0x0132
+#define MX23_PAD_GPMI_RDY1__SSP2_CMD 0x0142
+#define MX23_PAD_GPMI_WRN__SSP2_SCK 0x0182
+#define MX23_PAD_AUART1_CTS__SSP1_DATA4 0x01a2
+#define MX23_PAD_AUART1_RTS__SSP1_DATA5 0x01b2
+#define MX23_PAD_AUART1_RX__SSP1_DATA6 0x01c2
+#define MX23_PAD_AUART1_TX__SSP1_DATA7 0x01d2
+#define MX23_PAD_I2C_SCL__AUART1_TX 0x01e2
+#define MX23_PAD_I2C_SDA__AUART1_RX 0x01f2
+#define MX23_PAD_LCD_D08__SAIF2_SDATA0 0x1082
+#define MX23_PAD_LCD_D09__SAIF1_SDATA0 0x1092
+#define MX23_PAD_LCD_D10__SAIF_MCLK_BITCLK 0x10a2
+#define MX23_PAD_LCD_D11__SAIF_LRCLK 0x10b2
+#define MX23_PAD_LCD_D12__SAIF2_SDATA1 0x10c2
+#define MX23_PAD_LCD_D13__SAIF2_SDATA2 0x10d2
+#define MX23_PAD_LCD_D14__SAIF1_SDATA2 0x10e2
+#define MX23_PAD_LCD_D15__SAIF1_SDATA1 0x10f2
+#define MX23_PAD_LCD_D16__SAIF_ALT_BITCLK 0x1102
+#define MX23_PAD_LCD_RESET__GPMI_CE3N 0x1122
+#define MX23_PAD_PWM0__DUART_RX 0x11a2
+#define MX23_PAD_PWM1__DUART_TX 0x11b2
+#define MX23_PAD_PWM3__AUART1_CTS 0x11d2
+#define MX23_PAD_PWM4__AUART1_RTS 0x11e2
+#define MX23_PAD_SSP1_CMD__JTAG_TDO 0x2002
+#define MX23_PAD_SSP1_DETECT__USB_OTG_ID 0x2012
+#define MX23_PAD_SSP1_DATA0__JTAG_TDI 0x2022
+#define MX23_PAD_SSP1_DATA1__JTAG_TCLK 0x2032
+#define MX23_PAD_SSP1_DATA2__JTAG_RTCK 0x2042
+#define MX23_PAD_SSP1_DATA3__JTAG_TMS 0x2052
+#define MX23_PAD_SSP1_SCK__JTAG_TRST 0x2062
+#define MX23_PAD_ROTARYA__SPDIF 0x2072
+#define MX23_PAD_ROTARYB__GPMI_CE3N 0x2082
+#define MX23_PAD_GPMI_D00__GPIO_0_0 0x0003
+#define MX23_PAD_GPMI_D01__GPIO_0_1 0x0013
+#define MX23_PAD_GPMI_D02__GPIO_0_2 0x0023
+#define MX23_PAD_GPMI_D03__GPIO_0_3 0x0033
+#define MX23_PAD_GPMI_D04__GPIO_0_4 0x0043
+#define MX23_PAD_GPMI_D05__GPIO_0_5 0x0053
+#define MX23_PAD_GPMI_D06__GPIO_0_6 0x0063
+#define MX23_PAD_GPMI_D07__GPIO_0_7 0x0073
+#define MX23_PAD_GPMI_D08__GPIO_0_8 0x0083
+#define MX23_PAD_GPMI_D09__GPIO_0_9 0x0093
+#define MX23_PAD_GPMI_D10__GPIO_0_10 0x00a3
+#define MX23_PAD_GPMI_D11__GPIO_0_11 0x00b3
+#define MX23_PAD_GPMI_D12__GPIO_0_12 0x00c3
+#define MX23_PAD_GPMI_D13__GPIO_0_13 0x00d3
+#define MX23_PAD_GPMI_D14__GPIO_0_14 0x00e3
+#define MX23_PAD_GPMI_D15__GPIO_0_15 0x00f3
+#define MX23_PAD_GPMI_CLE__GPIO_0_16 0x0103
+#define MX23_PAD_GPMI_ALE__GPIO_0_17 0x0113
+#define MX23_PAD_GPMI_CE2N__GPIO_0_18 0x0123
+#define MX23_PAD_GPMI_RDY0__GPIO_0_19 0x0133
+#define MX23_PAD_GPMI_RDY1__GPIO_0_20 0x0143
+#define MX23_PAD_GPMI_RDY2__GPIO_0_21 0x0153
+#define MX23_PAD_GPMI_RDY3__GPIO_0_22 0x0163
+#define MX23_PAD_GPMI_WPN__GPIO_0_23 0x0173
+#define MX23_PAD_GPMI_WRN__GPIO_0_24 0x0183
+#define MX23_PAD_GPMI_RDN__GPIO_0_25 0x0193
+#define MX23_PAD_AUART1_CTS__GPIO_0_26 0x01a3
+#define MX23_PAD_AUART1_RTS__GPIO_0_27 0x01b3
+#define MX23_PAD_AUART1_RX__GPIO_0_28 0x01c3
+#define MX23_PAD_AUART1_TX__GPIO_0_29 0x01d3
+#define MX23_PAD_I2C_SCL__GPIO_0_30 0x01e3
+#define MX23_PAD_I2C_SDA__GPIO_0_31 0x01f3
+#define MX23_PAD_LCD_D00__GPIO_1_0 0x1003
+#define MX23_PAD_LCD_D01__GPIO_1_1 0x1013
+#define MX23_PAD_LCD_D02__GPIO_1_2 0x1023
+#define MX23_PAD_LCD_D03__GPIO_1_3 0x1033
+#define MX23_PAD_LCD_D04__GPIO_1_4 0x1043
+#define MX23_PAD_LCD_D05__GPIO_1_5 0x1053
+#define MX23_PAD_LCD_D06__GPIO_1_6 0x1063
+#define MX23_PAD_LCD_D07__GPIO_1_7 0x1073
+#define MX23_PAD_LCD_D08__GPIO_1_8 0x1083
+#define MX23_PAD_LCD_D09__GPIO_1_9 0x1093
+#define MX23_PAD_LCD_D10__GPIO_1_10 0x10a3
+#define MX23_PAD_LCD_D11__GPIO_1_11 0x10b3
+#define MX23_PAD_LCD_D12__GPIO_1_12 0x10c3
+#define MX23_PAD_LCD_D13__GPIO_1_13 0x10d3
+#define MX23_PAD_LCD_D14__GPIO_1_14 0x10e3
+#define MX23_PAD_LCD_D15__GPIO_1_15 0x10f3
+#define MX23_PAD_LCD_D16__GPIO_1_16 0x1103
+#define MX23_PAD_LCD_D17__GPIO_1_17 0x1113
+#define MX23_PAD_LCD_RESET__GPIO_1_18 0x1123
+#define MX23_PAD_LCD_RS__GPIO_1_19 0x1133
+#define MX23_PAD_LCD_WR__GPIO_1_20 0x1143
+#define MX23_PAD_LCD_CS__GPIO_1_21 0x1153
+#define MX23_PAD_LCD_DOTCK__GPIO_1_22 0x1163
+#define MX23_PAD_LCD_ENABLE__GPIO_1_23 0x1173
+#define MX23_PAD_LCD_HSYNC__GPIO_1_24 0x1183
+#define MX23_PAD_LCD_VSYNC__GPIO_1_25 0x1193
+#define MX23_PAD_PWM0__GPIO_1_26 0x11a3
+#define MX23_PAD_PWM1__GPIO_1_27 0x11b3
+#define MX23_PAD_PWM2__GPIO_1_28 0x11c3
+#define MX23_PAD_PWM3__GPIO_1_29 0x11d3
+#define MX23_PAD_PWM4__GPIO_1_30 0x11e3
+#define MX23_PAD_SSP1_CMD__GPIO_2_0 0x2003
+#define MX23_PAD_SSP1_DETECT__GPIO_2_1 0x2013
+#define MX23_PAD_SSP1_DATA0__GPIO_2_2 0x2023
+#define MX23_PAD_SSP1_DATA1__GPIO_2_3 0x2033
+#define MX23_PAD_SSP1_DATA2__GPIO_2_4 0x2043
+#define MX23_PAD_SSP1_DATA3__GPIO_2_5 0x2053
+#define MX23_PAD_SSP1_SCK__GPIO_2_6 0x2063
+#define MX23_PAD_ROTARYA__GPIO_2_7 0x2073
+#define MX23_PAD_ROTARYB__GPIO_2_8 0x2083
+#define MX23_PAD_EMI_A00__GPIO_2_9 0x2093
+#define MX23_PAD_EMI_A01__GPIO_2_10 0x20a3
+#define MX23_PAD_EMI_A02__GPIO_2_11 0x20b3
+#define MX23_PAD_EMI_A03__GPIO_2_12 0x20c3
+#define MX23_PAD_EMI_A04__GPIO_2_13 0x20d3
+#define MX23_PAD_EMI_A05__GPIO_2_14 0x20e3
+#define MX23_PAD_EMI_A06__GPIO_2_15 0x20f3
+#define MX23_PAD_EMI_A07__GPIO_2_16 0x2103
+#define MX23_PAD_EMI_A08__GPIO_2_17 0x2113
+#define MX23_PAD_EMI_A09__GPIO_2_18 0x2123
+#define MX23_PAD_EMI_A10__GPIO_2_19 0x2133
+#define MX23_PAD_EMI_A11__GPIO_2_20 0x2143
+#define MX23_PAD_EMI_A12__GPIO_2_21 0x2153
+#define MX23_PAD_EMI_BA0__GPIO_2_22 0x2163
+#define MX23_PAD_EMI_BA1__GPIO_2_23 0x2173
+#define MX23_PAD_EMI_CASN__GPIO_2_24 0x2183
+#define MX23_PAD_EMI_CE0N__GPIO_2_25 0x2193
+#define MX23_PAD_EMI_CE1N__GPIO_2_26 0x21a3
+#define MX23_PAD_GPMI_CE1N__GPIO_2_27 0x21b3
+#define MX23_PAD_GPMI_CE0N__GPIO_2_28 0x21c3
+#define MX23_PAD_EMI_CKE__GPIO_2_29 0x21d3
+#define MX23_PAD_EMI_RASN__GPIO_2_30 0x21e3
+#define MX23_PAD_EMI_WEN__GPIO_2_31 0x21f3
+
+#endif /* __DT_BINDINGS_MX23_PINCTRL_H__ */
diff --git a/arch/arm/boot/dts/imx23-stmp378x_devb.dts b/arch/arm/boot/dts/imx23-stmp378x_devb.dts
index 85c3864..cb64e2b 100644
--- a/arch/arm/boot/dts/imx23-stmp378x_devb.dts
+++ b/arch/arm/boot/dts/imx23-stmp378x_devb.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx23.dtsi"
+#include "imx23.dtsi"
/ {
model = "Freescale STMP378x Development Board";
@@ -39,12 +39,12 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x11d3 /* MX23_PAD_PWM3__GPIO_1_29 */
- 0x11e3 /* MX23_PAD_PWM4__GPIO_1_30 */
+ MX23_PAD_PWM3__GPIO_1_29
+ MX23_PAD_PWM4__GPIO_1_30
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
};
diff --git a/arch/arm/boot/dts/imx23.dtsi b/arch/arm/boot/dts/imx23.dtsi
index 28b5ce2..87faa6e 100644
--- a/arch/arm/boot/dts/imx23.dtsi
+++ b/arch/arm/boot/dts/imx23.dtsi
@@ -9,7 +9,8 @@
* http://www.gnu.org/copyleft/gpl.html
*/
-/include/ "skeleton.dtsi"
+#include "skeleton.dtsi"
+#include "imx23-pinfunc.h"
/ {
interrupt-parent = <&icoll>;
@@ -137,174 +138,174 @@
duart_pins_a: duart@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x11a2 /* MX23_PAD_PWM0__DUART_RX */
- 0x11b2 /* MX23_PAD_PWM1__DUART_TX */
+ MX23_PAD_PWM0__DUART_RX
+ MX23_PAD_PWM1__DUART_TX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart0_pins_a: auart0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x01c0 /* MX23_PAD_AUART1_RX__AUART1_RX */
- 0x01d0 /* MX23_PAD_AUART1_TX__AUART1_TX */
- 0x01a0 /* MX23_PAD_AUART1_CTS__AUART1_CTS */
- 0x01b0 /* MX23_PAD_AUART1_RTS__AUART1_RTS */
+ MX23_PAD_AUART1_RX__AUART1_RX
+ MX23_PAD_AUART1_TX__AUART1_TX
+ MX23_PAD_AUART1_CTS__AUART1_CTS
+ MX23_PAD_AUART1_RTS__AUART1_RTS
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart0_2pins_a: auart0-2pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x01e2 /* MX23_PAD_I2C_SCL__AUART1_TX */
- 0x01f2 /* MX23_PAD_I2C_SDA__AUART1_RX */
+ MX23_PAD_I2C_SCL__AUART1_TX
+ MX23_PAD_I2C_SDA__AUART1_RX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
gpmi_pins_a: gpmi-nand@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0000 /* MX23_PAD_GPMI_D00__GPMI_D00 */
- 0x0010 /* MX23_PAD_GPMI_D01__GPMI_D01 */
- 0x0020 /* MX23_PAD_GPMI_D02__GPMI_D02 */
- 0x0030 /* MX23_PAD_GPMI_D03__GPMI_D03 */
- 0x0040 /* MX23_PAD_GPMI_D04__GPMI_D04 */
- 0x0050 /* MX23_PAD_GPMI_D05__GPMI_D05 */
- 0x0060 /* MX23_PAD_GPMI_D06__GPMI_D06 */
- 0x0070 /* MX23_PAD_GPMI_D07__GPMI_D07 */
- 0x0100 /* MX23_PAD_GPMI_CLE__GPMI_CLE */
- 0x0110 /* MX23_PAD_GPMI_ALE__GPMI_ALE */
- 0x0130 /* MX23_PAD_GPMI_RDY0__GPMI_RDY0 */
- 0x0140 /* MX23_PAD_GPMI_RDY1__GPMI_RDY1 */
- 0x0170 /* MX23_PAD_GPMI_WPN__GPMI_WPN */
- 0x0180 /* MX23_PAD_GPMI_WRN__GPMI_WRN */
- 0x0190 /* MX23_PAD_GPMI_RDN__GPMI_RDN */
- 0x21b0 /* MX23_PAD_GPMI_CE1N__GPMI_CE1N */
- 0x21c0 /* MX23_PAD_GPMI_CE0N__GPMI_CE0N */
+ MX23_PAD_GPMI_D00__GPMI_D00
+ MX23_PAD_GPMI_D01__GPMI_D01
+ MX23_PAD_GPMI_D02__GPMI_D02
+ MX23_PAD_GPMI_D03__GPMI_D03
+ MX23_PAD_GPMI_D04__GPMI_D04
+ MX23_PAD_GPMI_D05__GPMI_D05
+ MX23_PAD_GPMI_D06__GPMI_D06
+ MX23_PAD_GPMI_D07__GPMI_D07
+ MX23_PAD_GPMI_CLE__GPMI_CLE
+ MX23_PAD_GPMI_ALE__GPMI_ALE
+ MX23_PAD_GPMI_RDY0__GPMI_RDY0
+ MX23_PAD_GPMI_RDY1__GPMI_RDY1
+ MX23_PAD_GPMI_WPN__GPMI_WPN
+ MX23_PAD_GPMI_WRN__GPMI_WRN
+ MX23_PAD_GPMI_RDN__GPMI_RDN
+ MX23_PAD_GPMI_CE1N__GPMI_CE1N
+ MX23_PAD_GPMI_CE0N__GPMI_CE0N
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
gpmi_pins_fixup: gpmi-pins-fixup {
fsl,pinmux-ids = <
- 0x0170 /* MX23_PAD_GPMI_WPN__GPMI_WPN */
- 0x0180 /* MX23_PAD_GPMI_WRN__GPMI_WRN */
- 0x0190 /* MX23_PAD_GPMI_RDN__GPMI_RDN */
+ MX23_PAD_GPMI_WPN__GPMI_WPN
+ MX23_PAD_GPMI_WRN__GPMI_WRN
+ MX23_PAD_GPMI_RDN__GPMI_RDN
>;
- fsl,drive-strength = <2>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
};
mmc0_4bit_pins_a: mmc0-4bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2020 /* MX23_PAD_SSP1_DATA0__SSP1_DATA0 */
- 0x2030 /* MX23_PAD_SSP1_DATA1__SSP1_DATA1 */
- 0x2040 /* MX23_PAD_SSP1_DATA2__SSP1_DATA2 */
- 0x2050 /* MX23_PAD_SSP1_DATA3__SSP1_DATA3 */
- 0x2000 /* MX23_PAD_SSP1_CMD__SSP1_CMD */
- 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */
+ MX23_PAD_SSP1_DATA0__SSP1_DATA0
+ MX23_PAD_SSP1_DATA1__SSP1_DATA1
+ MX23_PAD_SSP1_DATA2__SSP1_DATA2
+ MX23_PAD_SSP1_DATA3__SSP1_DATA3
+ MX23_PAD_SSP1_CMD__SSP1_CMD
+ MX23_PAD_SSP1_SCK__SSP1_SCK
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
mmc0_8bit_pins_a: mmc0-8bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2020 /* MX23_PAD_SSP1_DATA0__SSP1_DATA0 */
- 0x2030 /* MX23_PAD_SSP1_DATA1__SSP1_DATA1 */
- 0x2040 /* MX23_PAD_SSP1_DATA2__SSP1_DATA2 */
- 0x2050 /* MX23_PAD_SSP1_DATA3__SSP1_DATA3 */
- 0x0082 /* MX23_PAD_GPMI_D08__SSP1_DATA4 */
- 0x0092 /* MX23_PAD_GPMI_D09__SSP1_DATA5 */
- 0x00a2 /* MX23_PAD_GPMI_D10__SSP1_DATA6 */
- 0x00b2 /* MX23_PAD_GPMI_D11__SSP1_DATA7 */
- 0x2000 /* MX23_PAD_SSP1_CMD__SSP1_CMD */
- 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */
- 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */
+ MX23_PAD_SSP1_DATA0__SSP1_DATA0
+ MX23_PAD_SSP1_DATA1__SSP1_DATA1
+ MX23_PAD_SSP1_DATA2__SSP1_DATA2
+ MX23_PAD_SSP1_DATA3__SSP1_DATA3
+ MX23_PAD_GPMI_D08__SSP1_DATA4
+ MX23_PAD_GPMI_D09__SSP1_DATA5
+ MX23_PAD_GPMI_D10__SSP1_DATA6
+ MX23_PAD_GPMI_D11__SSP1_DATA7
+ MX23_PAD_SSP1_CMD__SSP1_CMD
+ MX23_PAD_SSP1_DETECT__SSP1_DETECT
+ MX23_PAD_SSP1_SCK__SSP1_SCK
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
mmc0_pins_fixup: mmc0-pins-fixup {
fsl,pinmux-ids = <
- 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */
- 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */
+ MX23_PAD_SSP1_DETECT__SSP1_DETECT
+ MX23_PAD_SSP1_SCK__SSP1_SCK
>;
- fsl,pull-up = <0>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
pwm2_pins_a: pwm2@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x11c0 /* MX23_PAD_PWM2__PWM2 */
+ MX23_PAD_PWM2__PWM2
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_24bit_pins_a: lcdif-24bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1000 /* MX23_PAD_LCD_D00__LCD_D0 */
- 0x1010 /* MX23_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX23_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX23_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX23_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX23_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX23_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX23_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX23_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX23_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX23_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX23_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX23_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX23_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX23_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX23_PAD_LCD_D15__LCD_D15 */
- 0x1100 /* MX23_PAD_LCD_D16__LCD_D16 */
- 0x1110 /* MX23_PAD_LCD_D17__LCD_D17 */
- 0x0081 /* MX23_PAD_GPMI_D08__LCD_D18 */
- 0x0091 /* MX23_PAD_GPMI_D09__LCD_D19 */
- 0x00a1 /* MX23_PAD_GPMI_D10__LCD_D20 */
- 0x00b1 /* MX23_PAD_GPMI_D11__LCD_D21 */
- 0x00c1 /* MX23_PAD_GPMI_D12__LCD_D22 */
- 0x00d1 /* MX23_PAD_GPMI_D13__LCD_D23 */
- 0x1160 /* MX23_PAD_LCD_DOTCK__LCD_DOTCK */
- 0x1170 /* MX23_PAD_LCD_ENABLE__LCD_ENABLE */
- 0x1180 /* MX23_PAD_LCD_HSYNC__LCD_HSYNC */
- 0x1190 /* MX23_PAD_LCD_VSYNC__LCD_VSYNC */
+ MX23_PAD_LCD_D00__LCD_D00
+ MX23_PAD_LCD_D01__LCD_D01
+ MX23_PAD_LCD_D02__LCD_D02
+ MX23_PAD_LCD_D03__LCD_D03
+ MX23_PAD_LCD_D04__LCD_D04
+ MX23_PAD_LCD_D05__LCD_D05
+ MX23_PAD_LCD_D06__LCD_D06
+ MX23_PAD_LCD_D07__LCD_D07
+ MX23_PAD_LCD_D08__LCD_D08
+ MX23_PAD_LCD_D09__LCD_D09
+ MX23_PAD_LCD_D10__LCD_D10
+ MX23_PAD_LCD_D11__LCD_D11
+ MX23_PAD_LCD_D12__LCD_D12
+ MX23_PAD_LCD_D13__LCD_D13
+ MX23_PAD_LCD_D14__LCD_D14
+ MX23_PAD_LCD_D15__LCD_D15
+ MX23_PAD_LCD_D16__LCD_D16
+ MX23_PAD_LCD_D17__LCD_D17
+ MX23_PAD_GPMI_D08__LCD_D18
+ MX23_PAD_GPMI_D09__LCD_D19
+ MX23_PAD_GPMI_D10__LCD_D20
+ MX23_PAD_GPMI_D11__LCD_D21
+ MX23_PAD_GPMI_D12__LCD_D22
+ MX23_PAD_GPMI_D13__LCD_D23
+ MX23_PAD_LCD_DOTCK__LCD_DOTCK
+ MX23_PAD_LCD_ENABLE__LCD_ENABLE
+ MX23_PAD_LCD_HSYNC__LCD_HSYNC
+ MX23_PAD_LCD_VSYNC__LCD_VSYNC
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
spi2_pins_a: spi2@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0182 /* MX23_PAD_GPMI_WRN__SSP2_SCK */
- 0x0142 /* MX23_PAD_GPMI_RDY1__SSP2_CMD */
- 0x0002 /* MX23_PAD_GPMI_D00__SSP2_DATA0 */
- 0x0032 /* MX23_PAD_GPMI_D03__SSP2_DATA3 */
+ MX23_PAD_GPMI_WRN__SSP2_SCK
+ MX23_PAD_GPMI_RDY1__SSP2_CMD
+ MX23_PAD_GPMI_D00__SSP2_DATA0
+ MX23_PAD_GPMI_D03__SSP2_DATA3
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx27-apf27dev.dts b/arch/arm/boot/dts/imx27-apf27dev.dts
index 2a377ca..47c8c26 100644
--- a/arch/arm/boot/dts/imx27-apf27dev.dts
+++ b/arch/arm/boot/dts/imx27-apf27dev.dts
@@ -16,6 +16,26 @@
model = "Armadeus Systems APF27Dev docking/development board";
compatible = "armadeus,imx27-apf27dev", "armadeus,imx27-apf27", "fsl,imx27";
+ display: display {
+ model = "Chimei-LW700AT9003";
+ native-mode = <&timing0>;
+ bits-per-pixel = <16>; /* non-standard but required */
+ fsl,pcr = <0xfae80083>; /* non-standard but required */
+ display-timings {
+ timing0: 640x480 {
+ clock-frequency = <33000033>;
+ hactive = <800>;
+ vactive = <640>;
+ hback-porch = <96>;
+ hfront-porch = <96>;
+ vback-porch = <20>;
+ vfront-porch = <21>;
+ hsync-len = <64>;
+ vsync-len = <4>;
+ };
+ };
+ };
+
gpio-keys {
compatible = "gpio-keys";
@@ -50,6 +70,12 @@
status = "okay";
};
+&fb {
+ display = <&display>;
+ fsl,dmacr = <0x00020010>;
+ status = "okay";
+};
+
&i2c1 {
clock-frequency = <400000>;
status = "okay";
diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/imx27.dtsi
index b7a1c6d..826231e 100644
--- a/arch/arm/boot/dts/imx27.dtsi
+++ b/arch/arm/boot/dts/imx27.dtsi
@@ -123,6 +123,7 @@
};
pwm: pwm@10006000 {
+ #pwm-cells = <2>;
compatible = "fsl,imx27-pwm";
reg = <0x10006000 0x1000>;
interrupts = <23>;
diff --git a/arch/arm/boot/dts/imx28-apf28.dts b/arch/arm/boot/dts/imx28-apf28.dts
index 7eb0758..7198fe3 100644
--- a/arch/arm/boot/dts/imx28-apf28.dts
+++ b/arch/arm/boot/dts/imx28-apf28.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "Armadeus Systems APF28 module";
diff --git a/arch/arm/boot/dts/imx28-apf28dev.dts b/arch/arm/boot/dts/imx28-apf28dev.dts
index b602494..e2efd8d 100644
--- a/arch/arm/boot/dts/imx28-apf28dev.dts
+++ b/arch/arm/boot/dts/imx28-apf28dev.dts
@@ -10,7 +10,7 @@
*/
/* APF28Dev is a docking board for the APF28 SOM */
-/include/ "imx28-apf28.dts"
+#include "imx28-apf28.dts"
/ {
model = "Armadeus Systems APF28Dev docking/development board";
@@ -41,30 +41,30 @@
hog_pins_apf28dev: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1103 /* MX28_PAD_LCD_D16__GPIO_1_16 */
- 0x1113 /* MX28_PAD_LCD_D17__GPIO_1_17 */
- 0x1123 /* MX28_PAD_LCD_D18__GPIO_1_18 */
- 0x1133 /* MX28_PAD_LCD_D19__GPIO_1_19 */
- 0x1143 /* MX28_PAD_LCD_D20__GPIO_1_20 */
- 0x1153 /* MX28_PAD_LCD_D21__GPIO_1_21 */
- 0x1163 /* MX28_PAD_LCD_D22__GPIO_1_22 */
+ MX28_PAD_LCD_D16__GPIO_1_16
+ MX28_PAD_LCD_D17__GPIO_1_17
+ MX28_PAD_LCD_D18__GPIO_1_18
+ MX28_PAD_LCD_D19__GPIO_1_19
+ MX28_PAD_LCD_D20__GPIO_1_20
+ MX28_PAD_LCD_D21__GPIO_1_21
+ MX28_PAD_LCD_D22__GPIO_1_22
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_apf28dev: lcdif-apf28dev@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-apx4devkit.dts b/arch/arm/boot/dts/imx28-apx4devkit.dts
index 0e7fed4..6f254ca 100644
--- a/arch/arm/boot/dts/imx28-apx4devkit.dts
+++ b/arch/arm/boot/dts/imx28-apx4devkit.dts
@@ -1,5 +1,5 @@
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "Bluegiga APX4 Development Kit";
@@ -40,53 +40,53 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0113 /* MX28_PAD_GPMI_CE1N__GPIO_0_17 */
- 0x0153 /* MX28_PAD_GPMI_RDY1__GPIO_0_21 */
- 0x2123 /* MX28_PAD_SSP2_MISO__GPIO_2_18 */
- 0x2131 /* MX28_PAD_SSP2_SS0__GPIO_2_19 */
- 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */
- 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
- 0x4143 /* MX28_PAD_JTAG_RTCK__GPIO_4_20 */
+ MX28_PAD_GPMI_CE1N__GPIO_0_17
+ MX28_PAD_GPMI_RDY1__GPIO_0_21
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_SSP2_SS0__AUART3_TX /* was: 0x2131 - MX28_PAD_SSP2_SS0__GPIO_2_19 */
+ MX28_PAD_PWM3__GPIO_3_28
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ MX28_PAD_JTAG_RTCK__GPIO_4_20
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_apx4: lcdif-apx4@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2041 /* MX28_PAD_SSP0_DATA4__SSP2_D0 */
- 0x2051 /* MX28_PAD_SSP0_DATA5__SSP2_D3 */
- 0x2061 /* MX28_PAD_SSP0_DATA6__SSP2_CMD */
- 0x2071 /* MX28_PAD_SSP0_DATA7__SSP2_SCK */
- 0x2141 /* MX28_PAD_SSP2_SS1__SSP2_D1 */
- 0x2151 /* MX28_PAD_SSP2_SS2__SSP2_D2 */
+ MX28_PAD_SSP0_DATA4__SSP2_D0
+ MX28_PAD_SSP0_DATA5__SSP2_D3
+ MX28_PAD_SSP0_DATA6__SSP2_CMD
+ MX28_PAD_SSP0_DATA7__SSP2_SCK
+ MX28_PAD_SSP2_SS1__SSP2_D1
+ MX28_PAD_SSP2_SS2__SSP2_D2
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4 {
fsl,pinmux-ids = <
- 0x2071 /* MX28_PAD_SSP0_DATA7__SSP2_SCK */
+ MX28_PAD_SSP0_DATA7__SSP2_SCK
>;
- fsl,drive-strength = <2>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts
index 1ec8c94..cabb617 100644
--- a/arch/arm/boot/dts/imx28-cfa10036.dts
+++ b/arch/arm/boot/dts/imx28-cfa10036.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "Crystalfontz CFA-10036 Board";
@@ -26,31 +26,31 @@
ssd1306_cfa10036: ssd1306-10036@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2073 /* MX28_PAD_SSP0_D7__GPIO_2_7 */
+ MX28_PAD_SSP0_DATA7__GPIO_2_7
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
led_pins_cfa10036: leds-10036@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3043 /* MX28_PAD_AUART1_RX__GPIO_3_4 */
+ MX28_PAD_AUART1_RX__GPIO_3_4
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
usb0_otg_cfa10036: otg-10036@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0142 /* MX28_PAD_GPMI_READY0__USB0_ID */
+ MX28_PAD_GPMI_RDY0__USB0_ID
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-cfa10037.dts b/arch/arm/boot/dts/imx28-cfa10037.dts
index 182b99f..f93e9a7 100644
--- a/arch/arm/boot/dts/imx28-cfa10037.dts
+++ b/arch/arm/boot/dts/imx28-cfa10037.dts
@@ -13,7 +13,7 @@
* The CFA-10049 is an expansion board for the CFA-10036 module, thus we
* need to include the CFA-10036 DTS.
*/
-/include/ "imx28-cfa10036.dts"
+#include "imx28-cfa10036.dts"
/ {
model = "Crystalfontz CFA-10037 Board";
@@ -25,21 +25,21 @@
usb_pins_cfa10037: usb-10037@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+ MX28_PAD_GPMI_D07__GPIO_0_7
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
mac0_pins_cfa10037: mac0-10037@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */
+ MX28_PAD_SSP2_SS2__GPIO_2_21
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
};
diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
index 06e4cfa..7087b4b 100644
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ b/arch/arm/boot/dts/imx28-cfa10049.dts
@@ -13,7 +13,7 @@
* The CFA-10049 is an expansion board for the CFA-10036 module, thus we
* need to include the CFA-10036 DTS.
*/
-/include/ "imx28-cfa10036.dts"
+#include "imx28-cfa10036.dts"
/ {
model = "Crystalfontz CFA-10049 Board";
@@ -25,150 +25,150 @@
usb_pins_cfa10049: usb-10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+ MX28_PAD_GPMI_D07__GPIO_0_7
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
i2cmux_pins_cfa10049: i2cmux-10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1163 /* MX28_PAD_LCD_D22__GPIO_1_22 */
- 0x1173 /* MX28_PAD_LCD_D22__GPIO_1_23 */
+ MX28_PAD_LCD_D22__GPIO_1_22
+ MX28_PAD_LCD_D23__GPIO_1_23
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
mac0_pins_cfa10049: mac0-10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */
+ MX28_PAD_SSP2_SS2__GPIO_2_21
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
pca_pins_cfa10049: pca-10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2133 /* MX28_PAD_SSP2_D3__GPIO_2_19 */
+ MX28_PAD_SSP2_SS0__GPIO_2_19
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
rotary_pins_cfa10049: rotary-10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3183 /* MX28_PAD_I2C0_SCL__GPIO_3_24 */
- 0x3193 /* MX28_PAD_I2C0_SDA__GPIO_3_25 */
+ MX28_PAD_I2C0_SCL__GPIO_3_24
+ MX28_PAD_I2C0_SDA__GPIO_3_25
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
rotary_btn_pins_cfa10049: rotary-btn-10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31a3 /* MX28_PAD_SAIF_SDATA0__GPIO_3_26 */
+ MX28_PAD_SAIF1_SDATA0__GPIO_3_26
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
spi2_pins_cfa10049: spi2-cfa10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */
- 0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */
- 0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */
- 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
+ MX28_PAD_SSP2_SCK__GPIO_2_16
+ MX28_PAD_SSP2_MOSI__GPIO_2_17
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_AUART1_TX__GPIO_3_5
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
spi3_pins_cfa10049: spi3-cfa10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0183 /* MX28_PAD_GPMI_RDN__GPIO_0_24 */
- 0x01c3 /* MX28_PAD_GPMI_RESETN__GPIO_0_28 */
- 0x0113 /* MX28_PAD_GPMI_CE1N__GPIO_0_17 */
- 0x01a3 /* MX28_PAD_GPMI_ALE__GPIO_0_26 */
- 0x01b3 /* MX28_PAD_GPMI_CLE__GPIO_0_27 */
+ MX28_PAD_GPMI_RDN__GPIO_0_24
+ MX28_PAD_GPMI_RESETN__GPIO_0_28
+ MX28_PAD_GPMI_CE1N__GPIO_0_17
+ MX28_PAD_GPMI_ALE__GPIO_0_26
+ MX28_PAD_GPMI_CLE__GPIO_0_27
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
lcdif_18bit_pins_cfa10049: lcdif-18bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */
- 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */
- 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */
- 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10049: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10049_pullup: lcdif-10049-pullup@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+ MX28_PAD_LCD_RESET__GPIO_3_30
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
w1_gpio_pins: w1-gpio@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1153 /* MX28_PAD_LCD_D21__GPIO_1_21 */
+ MX28_PAD_LCD_D21__GPIO_1_21
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>; /* 0 will enable the keeper */
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>; /* 0 will enable the keeper */
};
};
diff --git a/arch/arm/boot/dts/imx28-cfa10055.dts b/arch/arm/boot/dts/imx28-cfa10055.dts
index 171bcbe..c3900e7 100644
--- a/arch/arm/boot/dts/imx28-cfa10055.dts
+++ b/arch/arm/boot/dts/imx28-cfa10055.dts
@@ -14,7 +14,7 @@
* The CFA-10055 is an expansion board for the CFA-10036 module and
* CFA-10037, thus we need to include the CFA-10037 DTS.
*/
-/include/ "imx28-cfa10037.dts"
+#include "imx28-cfa10037.dts"
/ {
model = "Crystalfontz CFA-10055 Board";
@@ -26,64 +26,64 @@
spi2_pins_cfa10055: spi2-cfa10055@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */
- 0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */
- 0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */
- 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
+ MX28_PAD_SSP2_SCK__GPIO_2_16
+ MX28_PAD_SSP2_MOSI__GPIO_2_17
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_AUART1_TX__GPIO_3_5
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
lcdif_18bit_pins_cfa10055: lcdif-18bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */
- 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */
- 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */
- 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10055: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+ MX28_PAD_LCD_RESET__GPIO_3_30
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-cfa10056.dts b/arch/arm/boot/dts/imx28-cfa10056.dts
index b45dd0e..cef959a 100644
--- a/arch/arm/boot/dts/imx28-cfa10056.dts
+++ b/arch/arm/boot/dts/imx28-cfa10056.dts
@@ -13,7 +13,7 @@
* The CFA-10055 is an expansion board for the CFA-10036 module and
* CFA-10037, thus we need to include the CFA-10037 DTS.
*/
-/include/ "imx28-cfa10037.dts"
+#include "imx28-cfa10037.dts"
/ {
model = "Crystalfontz CFA-10056 Board";
@@ -25,37 +25,37 @@
spi2_pins_cfa10056: spi2-cfa10056@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */
- 0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */
- 0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */
- 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
+ MX28_PAD_SSP2_SCK__GPIO_2_16
+ MX28_PAD_SSP2_MOSI__GPIO_2_17
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_AUART1_TX__GPIO_3_5
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
lcdif_pins_cfa10056: lcdif-10056@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10056_pullup: lcdif-10056-pullup@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+ MX28_PAD_LCD_RESET__GPIO_3_30
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-cfa10057.dts b/arch/arm/boot/dts/imx28-cfa10057.dts
index 0333c05..3c13128 100644
--- a/arch/arm/boot/dts/imx28-cfa10057.dts
+++ b/arch/arm/boot/dts/imx28-cfa10057.dts
@@ -14,7 +14,7 @@
* The CFA-10057 is an expansion board for the CFA-10036 module, thus we
* need to include the CFA-10036 DTS.
*/
-/include/ "imx28-cfa10036.dts"
+#include "imx28-cfa10036.dts"
/ {
model = "Crystalfontz CFA-10057 Board";
@@ -26,51 +26,51 @@
usb_pins_cfa10057: usb-10057@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+ MX28_PAD_GPMI_D07__GPIO_0_7
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_18bit_pins_cfa10057: lcdif-18bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */
- 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */
- 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */
- 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10057: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-cfa10058.dts b/arch/arm/boot/dts/imx28-cfa10058.dts
index 64c64c5..2469d34 100644
--- a/arch/arm/boot/dts/imx28-cfa10058.dts
+++ b/arch/arm/boot/dts/imx28-cfa10058.dts
@@ -14,7 +14,7 @@
* The CFA-10058 is an expansion board for the CFA-10036 module, thus we
* need to include the CFA-10036 DTS.
*/
-/include/ "imx28-cfa10036.dts"
+#include "imx28-cfa10036.dts"
/ {
model = "Crystalfontz CFA-10058 Board";
@@ -26,24 +26,24 @@
usb_pins_cfa10058: usb-10058@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+ MX28_PAD_GPMI_D07__GPIO_0_7
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10058: lcdif-10058@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
index 15715d9..1f63845 100644
--- a/arch/arm/boot/dts/imx28-evk.dts
+++ b/arch/arm/boot/dts/imx28-evk.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "Freescale i.MX28 Evaluation Kit";
@@ -70,52 +70,52 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x20d3 /* MX28_PAD_SSP1_CMD__GPIO_2_13 */
- 0x20f3 /* MX28_PAD_SSP1_DATA3__GPIO_2_15 */
- 0x40d3 /* MX28_PAD_ENET0_RX_CLK__GPIO_4_13 */
- 0x20c3 /* MX28_PAD_SSP1_SCK__GPIO_2_12 */
- 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */
- 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
- 0x3083 /* MX28_PAD_AUART2_RX__GPIO_3_8 */
- 0x3093 /* MX28_PAD_AUART2_TX__GPIO_3_9 */
+ MX28_PAD_SSP1_CMD__GPIO_2_13
+ MX28_PAD_SSP1_DATA3__GPIO_2_15
+ MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+ MX28_PAD_SSP1_SCK__GPIO_2_12
+ MX28_PAD_PWM3__GPIO_3_28
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ MX28_PAD_AUART2_RX__GPIO_3_8
+ MX28_PAD_AUART2_TX__GPIO_3_9
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
led_pin_gpio3_5: led_gpio3_5@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
+ MX28_PAD_AUART1_TX__GPIO_3_5
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
gpmi_pins_evk: gpmi-nand-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0110 /* MX28_PAD_GPMI_CE1N__GPMI_CE1N */
- 0x0150 /* MX28_PAD_GPMI_RDY1__GPMI_READY1 */
+ MX28_PAD_GPMI_CE1N__GPMI_CE1N
+ MX28_PAD_GPMI_RDY1__GPMI_READY1
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_evk: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
@@ -182,6 +182,7 @@
};
lradc@80050000 {
+ fsl,lradc-touchscreen-wires = <4>;
status = "okay";
};
@@ -242,6 +243,8 @@
ahb@80080000 {
usb0: usb@80080000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_pins_a>;
vbus-supply = <®_usb0_vbus>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/imx28-m28cu3.dts b/arch/arm/boot/dts/imx28-m28cu3.dts
new file mode 100644
index 0000000..d3958da
--- /dev/null
+++ b/arch/arm/boot/dts/imx28-m28cu3.dts
@@ -0,0 +1,266 @@
+/*
+ * Copyright (C) 2013 Marek Vasut <marex@denx.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx28.dtsi"
+
+/ {
+ model = "MSR M28CU3";
+ compatible = "msr,m28cu3", "fsl,imx28";
+
+ memory {
+ reg = <0x40000000 0x08000000>;
+ };
+
+ apb@80000000 {
+ apbh@80000000 {
+ gpmi-nand@8000c000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+ status = "okay";
+
+ partition@0 {
+ label = "gpmi-nfc-0-boot";
+ reg = <0x00000000 0x01400000>;
+ read-only;
+ };
+
+ partition@1 {
+ label = "gpmi-nfc-general-use";
+ reg = <0x01400000 0x0ec00000>;
+ };
+ };
+
+ ssp0: ssp@80010000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_4bit_pins_a
+ &mmc0_cd_cfg
+ &mmc0_sck_cfg>;
+ bus-width = <4>;
+ vmmc-supply = <®_vddio_sd0>;
+ status = "okay";
+ };
+
+ ssp2: ssp@80014000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_4bit_pins_a
+ &mmc2_cd_cfg
+ &mmc2_sck_cfg>;
+ bus-width = <4>;
+ vmmc-supply = <®_vddio_sd1>;
+ status = "okay";
+ };
+
+ pinctrl@80018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP2_SS0__GPIO_2_19
+ MX28_PAD_PWM4__GPIO_3_29
+ MX28_PAD_AUART2_RX__GPIO_3_8
+ MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_m28: lcdif-m28@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_VSYNC__LCD_VSYNC
+ MX28_PAD_LCD_HSYNC__LCD_HSYNC
+ MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
+ MX28_PAD_LCD_RESET__LCD_RESET
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ MX28_PAD_AUART1_TX__GPIO_3_5
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_pins_gpio: leds-m28@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP3_MISO__GPIO_2_26
+ MX28_PAD_SSP3_SCK__GPIO_2_24
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+ };
+
+ ocotp@8002c000 {
+ status = "okay";
+ };
+
+ lcdif@80030000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_24bit_pins_a
+ &lcdif_pins_m28>;
+ display = <&display>;
+ reset-active-high;
+ status = "okay";
+
+ display: display0 {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <6410256>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vfront-porch = <5>;
+ hsync-len = <30>;
+ vsync-len = <3>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+ };
+ };
+
+ apbx@80040000 {
+ duart: serial@80074000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_b>;
+ status = "okay";
+ };
+
+ usbphy1: usbphy@8007e000 {
+ status = "okay";
+ };
+
+ auart0: serial@8006a000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_2pins_a>;
+ status = "okay";
+ };
+
+ auart3: serial@80070000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart3_2pins_b>;
+ status = "okay";
+ };
+
+ pwm: pwm@80064000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm3_pins_a>;
+ status = "okay";
+ };
+ };
+ };
+
+ ahb@80080000 {
+ usb1: usb@80090000 {
+ vbus-supply = <®_usb1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usbphy1_pins_a>;
+ disable-over-current;
+ status = "okay";
+ };
+
+ mac0: ethernet@800f0000 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ phy-reset-gpios = <&gpio4 13 0>;
+ phy-reset-duration = <100>;
+ status = "okay";
+ };
+
+ mac1: ethernet@800f4000 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac1_pins_a>;
+ status = "okay";
+ };
+ };
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 3 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_gpio>;
+
+ user1 {
+ label = "sd0-led";
+ gpios = <&gpio2 26 0>;
+ linux,default-trigger = "mmc0";
+ };
+
+ user2 {
+ label = "sd1-led";
+ gpios = <&gpio2 24 0>;
+ linux,default-trigger = "mmc2";
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+
+ reg_3p3v: 3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_vddio_sd0: vddio-sd0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vddio-sd0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 29 0>;
+ };
+
+ reg_vddio_sd1: vddio-sd1 {
+ compatible = "regulator-fixed";
+ regulator-name = "vddio-sd1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 19 0>;
+ };
+
+ reg_usb1_vbus: usb1_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 8 0>;
+ enable-active-high;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts
index 0d322a2..8e2477f 100644
--- a/arch/arm/boot/dts/imx28-m28evk.dts
+++ b/arch/arm/boot/dts/imx28-m28evk.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "DENX M28EVK";
@@ -92,26 +92,26 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */
- 0x30a3 /* MX28_PAD_AUART2_CTS__GPIO_3_10 */
- 0x30b3 /* MX28_PAD_AUART2_RTS__GPIO_3_11 */
- 0x30c3 /* MX28_PAD_AUART3_RX__GPIO_3_12 */
- 0x30d3 /* MX28_PAD_AUART3_TX__GPIO_3_13 */
+ MX28_PAD_PWM3__GPIO_3_28
+ MX28_PAD_AUART2_CTS__GPIO_3_10
+ MX28_PAD_AUART2_RTS__GPIO_3_11
+ MX28_PAD_AUART3_RX__GPIO_3_12
+ MX28_PAD_AUART3_TX__GPIO_3_13
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_m28: lcdif-m28@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x11e0 /* MX28_PAD_LCD_DOTCLK__LCD_DOTCLK */
- 0x11f0 /* MX28_PAD_LCD_ENABLE__LCD_ENABLE */
+ MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
+ MX28_PAD_LCD_ENABLE__LCD_ENABLE
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-pinfunc.h b/arch/arm/boot/dts/imx28-pinfunc.h
new file mode 100644
index 0000000..e11f69b
--- /dev/null
+++ b/arch/arm/boot/dts/imx28-pinfunc.h
@@ -0,0 +1,506 @@
+/*
+ * Header providing constants for i.MX28 pinctrl bindings.
+ *
+ * Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#ifndef __DT_BINDINGS_MX28_PINCTRL_H__
+#define __DT_BINDINGS_MX28_PINCTRL_H__
+
+#include "mxs-pinfunc.h"
+
+#define MX28_PAD_GPMI_D00__GPMI_D0 0x0000
+#define MX28_PAD_GPMI_D01__GPMI_D1 0x0010
+#define MX28_PAD_GPMI_D02__GPMI_D2 0x0020
+#define MX28_PAD_GPMI_D03__GPMI_D3 0x0030
+#define MX28_PAD_GPMI_D04__GPMI_D4 0x0040
+#define MX28_PAD_GPMI_D05__GPMI_D5 0x0050
+#define MX28_PAD_GPMI_D06__GPMI_D6 0x0060
+#define MX28_PAD_GPMI_D07__GPMI_D7 0x0070
+#define MX28_PAD_GPMI_CE0N__GPMI_CE0N 0x0100
+#define MX28_PAD_GPMI_CE1N__GPMI_CE1N 0x0110
+#define MX28_PAD_GPMI_CE2N__GPMI_CE2N 0x0120
+#define MX28_PAD_GPMI_CE3N__GPMI_CE3N 0x0130
+#define MX28_PAD_GPMI_RDY0__GPMI_READY0 0x0140
+#define MX28_PAD_GPMI_RDY1__GPMI_READY1 0x0150
+#define MX28_PAD_GPMI_RDY2__GPMI_READY2 0x0160
+#define MX28_PAD_GPMI_RDY3__GPMI_READY3 0x0170
+#define MX28_PAD_GPMI_RDN__GPMI_RDN 0x0180
+#define MX28_PAD_GPMI_WRN__GPMI_WRN 0x0190
+#define MX28_PAD_GPMI_ALE__GPMI_ALE 0x01a0
+#define MX28_PAD_GPMI_CLE__GPMI_CLE 0x01b0
+#define MX28_PAD_GPMI_RESETN__GPMI_RESETN 0x01c0
+#define MX28_PAD_LCD_D00__LCD_D0 0x1000
+#define MX28_PAD_LCD_D01__LCD_D1 0x1010
+#define MX28_PAD_LCD_D02__LCD_D2 0x1020
+#define MX28_PAD_LCD_D03__LCD_D3 0x1030
+#define MX28_PAD_LCD_D04__LCD_D4 0x1040
+#define MX28_PAD_LCD_D05__LCD_D5 0x1050
+#define MX28_PAD_LCD_D06__LCD_D6 0x1060
+#define MX28_PAD_LCD_D07__LCD_D7 0x1070
+#define MX28_PAD_LCD_D08__LCD_D8 0x1080
+#define MX28_PAD_LCD_D09__LCD_D9 0x1090
+#define MX28_PAD_LCD_D10__LCD_D10 0x10a0
+#define MX28_PAD_LCD_D11__LCD_D11 0x10b0
+#define MX28_PAD_LCD_D12__LCD_D12 0x10c0
+#define MX28_PAD_LCD_D13__LCD_D13 0x10d0
+#define MX28_PAD_LCD_D14__LCD_D14 0x10e0
+#define MX28_PAD_LCD_D15__LCD_D15 0x10f0
+#define MX28_PAD_LCD_D16__LCD_D16 0x1100
+#define MX28_PAD_LCD_D17__LCD_D17 0x1110
+#define MX28_PAD_LCD_D18__LCD_D18 0x1120
+#define MX28_PAD_LCD_D19__LCD_D19 0x1130
+#define MX28_PAD_LCD_D20__LCD_D20 0x1140
+#define MX28_PAD_LCD_D21__LCD_D21 0x1150
+#define MX28_PAD_LCD_D22__LCD_D22 0x1160
+#define MX28_PAD_LCD_D23__LCD_D23 0x1170
+#define MX28_PAD_LCD_RD_E__LCD_RD_E 0x1180
+#define MX28_PAD_LCD_WR_RWN__LCD_WR_RWN 0x1190
+#define MX28_PAD_LCD_RS__LCD_RS 0x11a0
+#define MX28_PAD_LCD_CS__LCD_CS 0x11b0
+#define MX28_PAD_LCD_VSYNC__LCD_VSYNC 0x11c0
+#define MX28_PAD_LCD_HSYNC__LCD_HSYNC 0x11d0
+#define MX28_PAD_LCD_DOTCLK__LCD_DOTCLK 0x11e0
+#define MX28_PAD_LCD_ENABLE__LCD_ENABLE 0x11f0
+#define MX28_PAD_SSP0_DATA0__SSP0_D0 0x2000
+#define MX28_PAD_SSP0_DATA1__SSP0_D1 0x2010
+#define MX28_PAD_SSP0_DATA2__SSP0_D2 0x2020
+#define MX28_PAD_SSP0_DATA3__SSP0_D3 0x2030
+#define MX28_PAD_SSP0_DATA4__SSP0_D4 0x2040
+#define MX28_PAD_SSP0_DATA5__SSP0_D5 0x2050
+#define MX28_PAD_SSP0_DATA6__SSP0_D6 0x2060
+#define MX28_PAD_SSP0_DATA7__SSP0_D7 0x2070
+#define MX28_PAD_SSP0_CMD__SSP0_CMD 0x2080
+#define MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT 0x2090
+#define MX28_PAD_SSP0_SCK__SSP0_SCK 0x20a0
+#define MX28_PAD_SSP1_SCK__SSP1_SCK 0x20c0
+#define MX28_PAD_SSP1_CMD__SSP1_CMD 0x20d0
+#define MX28_PAD_SSP1_DATA0__SSP1_D0 0x20e0
+#define MX28_PAD_SSP1_DATA3__SSP1_D3 0x20f0
+#define MX28_PAD_SSP2_SCK__SSP2_SCK 0x2100
+#define MX28_PAD_SSP2_MOSI__SSP2_CMD 0x2110
+#define MX28_PAD_SSP2_MISO__SSP2_D0 0x2120
+#define MX28_PAD_SSP2_SS0__SSP2_D3 0x2130
+#define MX28_PAD_SSP2_SS1__SSP2_D4 0x2140
+#define MX28_PAD_SSP2_SS2__SSP2_D5 0x2150
+#define MX28_PAD_SSP3_SCK__SSP3_SCK 0x2180
+#define MX28_PAD_SSP3_MOSI__SSP3_CMD 0x2190
+#define MX28_PAD_SSP3_MISO__SSP3_D0 0x21a0
+#define MX28_PAD_SSP3_SS0__SSP3_D3 0x21b0
+#define MX28_PAD_AUART0_RX__AUART0_RX 0x3000
+#define MX28_PAD_AUART0_TX__AUART0_TX 0x3010
+#define MX28_PAD_AUART0_CTS__AUART0_CTS 0x3020
+#define MX28_PAD_AUART0_RTS__AUART0_RTS 0x3030
+#define MX28_PAD_AUART1_RX__AUART1_RX 0x3040
+#define MX28_PAD_AUART1_TX__AUART1_TX 0x3050
+#define MX28_PAD_AUART1_CTS__AUART1_CTS 0x3060
+#define MX28_PAD_AUART1_RTS__AUART1_RTS 0x3070
+#define MX28_PAD_AUART2_RX__AUART2_RX 0x3080
+#define MX28_PAD_AUART2_TX__AUART2_TX 0x3090
+#define MX28_PAD_AUART2_CTS__AUART2_CTS 0x30a0
+#define MX28_PAD_AUART2_RTS__AUART2_RTS 0x30b0
+#define MX28_PAD_AUART3_RX__AUART3_RX 0x30c0
+#define MX28_PAD_AUART3_TX__AUART3_TX 0x30d0
+#define MX28_PAD_AUART3_CTS__AUART3_CTS 0x30e0
+#define MX28_PAD_AUART3_RTS__AUART3_RTS 0x30f0
+#define MX28_PAD_PWM0__PWM_0 0x3100
+#define MX28_PAD_PWM1__PWM_1 0x3110
+#define MX28_PAD_PWM2__PWM_2 0x3120
+#define MX28_PAD_SAIF0_MCLK__SAIF0_MCLK 0x3140
+#define MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK 0x3150
+#define MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK 0x3160
+#define MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 0x3170
+#define MX28_PAD_I2C0_SCL__I2C0_SCL 0x3180
+#define MX28_PAD_I2C0_SDA__I2C0_SDA 0x3190
+#define MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 0x31a0
+#define MX28_PAD_SPDIF__SPDIF_TX 0x31b0
+#define MX28_PAD_PWM3__PWM_3 0x31c0
+#define MX28_PAD_PWM4__PWM_4 0x31d0
+#define MX28_PAD_LCD_RESET__LCD_RESET 0x31e0
+#define MX28_PAD_ENET0_MDC__ENET0_MDC 0x4000
+#define MX28_PAD_ENET0_MDIO__ENET0_MDIO 0x4010
+#define MX28_PAD_ENET0_RX_EN__ENET0_RX_EN 0x4020
+#define MX28_PAD_ENET0_RXD0__ENET0_RXD0 0x4030
+#define MX28_PAD_ENET0_RXD1__ENET0_RXD1 0x4040
+#define MX28_PAD_ENET0_TX_CLK__ENET0_TX_CLK 0x4050
+#define MX28_PAD_ENET0_TX_EN__ENET0_TX_EN 0x4060
+#define MX28_PAD_ENET0_TXD0__ENET0_TXD0 0x4070
+#define MX28_PAD_ENET0_TXD1__ENET0_TXD1 0x4080
+#define MX28_PAD_ENET0_RXD2__ENET0_RXD2 0x4090
+#define MX28_PAD_ENET0_RXD3__ENET0_RXD3 0x40a0
+#define MX28_PAD_ENET0_TXD2__ENET0_TXD2 0x40b0
+#define MX28_PAD_ENET0_TXD3__ENET0_TXD3 0x40c0
+#define MX28_PAD_ENET0_RX_CLK__ENET0_RX_CLK 0x40d0
+#define MX28_PAD_ENET0_COL__ENET0_COL 0x40e0
+#define MX28_PAD_ENET0_CRS__ENET0_CRS 0x40f0
+#define MX28_PAD_ENET_CLK__CLKCTRL_ENET 0x4100
+#define MX28_PAD_JTAG_RTCK__JTAG_RTCK 0x4140
+#define MX28_PAD_EMI_D00__EMI_DATA0 0x5000
+#define MX28_PAD_EMI_D01__EMI_DATA1 0x5010
+#define MX28_PAD_EMI_D02__EMI_DATA2 0x5020
+#define MX28_PAD_EMI_D03__EMI_DATA3 0x5030
+#define MX28_PAD_EMI_D04__EMI_DATA4 0x5040
+#define MX28_PAD_EMI_D05__EMI_DATA5 0x5050
+#define MX28_PAD_EMI_D06__EMI_DATA6 0x5060
+#define MX28_PAD_EMI_D07__EMI_DATA7 0x5070
+#define MX28_PAD_EMI_D08__EMI_DATA8 0x5080
+#define MX28_PAD_EMI_D09__EMI_DATA9 0x5090
+#define MX28_PAD_EMI_D10__EMI_DATA10 0x50a0
+#define MX28_PAD_EMI_D11__EMI_DATA11 0x50b0
+#define MX28_PAD_EMI_D12__EMI_DATA12 0x50c0
+#define MX28_PAD_EMI_D13__EMI_DATA13 0x50d0
+#define MX28_PAD_EMI_D14__EMI_DATA14 0x50e0
+#define MX28_PAD_EMI_D15__EMI_DATA15 0x50f0
+#define MX28_PAD_EMI_ODT0__EMI_ODT0 0x5100
+#define MX28_PAD_EMI_DQM0__EMI_DQM0 0x5110
+#define MX28_PAD_EMI_ODT1__EMI_ODT1 0x5120
+#define MX28_PAD_EMI_DQM1__EMI_DQM1 0x5130
+#define MX28_PAD_EMI_DDR_OPEN_FB__EMI_DDR_OPEN_FEEDBACK 0x5140
+#define MX28_PAD_EMI_CLK__EMI_CLK 0x5150
+#define MX28_PAD_EMI_DQS0__EMI_DQS0 0x5160
+#define MX28_PAD_EMI_DQS1__EMI_DQS1 0x5170
+#define MX28_PAD_EMI_DDR_OPEN__EMI_DDR_OPEN 0x51a0
+#define MX28_PAD_EMI_A00__EMI_ADDR0 0x6000
+#define MX28_PAD_EMI_A01__EMI_ADDR1 0x6010
+#define MX28_PAD_EMI_A02__EMI_ADDR2 0x6020
+#define MX28_PAD_EMI_A03__EMI_ADDR3 0x6030
+#define MX28_PAD_EMI_A04__EMI_ADDR4 0x6040
+#define MX28_PAD_EMI_A05__EMI_ADDR5 0x6050
+#define MX28_PAD_EMI_A06__EMI_ADDR6 0x6060
+#define MX28_PAD_EMI_A07__EMI_ADDR7 0x6070
+#define MX28_PAD_EMI_A08__EMI_ADDR8 0x6080
+#define MX28_PAD_EMI_A09__EMI_ADDR9 0x6090
+#define MX28_PAD_EMI_A10__EMI_ADDR10 0x60a0
+#define MX28_PAD_EMI_A11__EMI_ADDR11 0x60b0
+#define MX28_PAD_EMI_A12__EMI_ADDR12 0x60c0
+#define MX28_PAD_EMI_A13__EMI_ADDR13 0x60d0
+#define MX28_PAD_EMI_A14__EMI_ADDR14 0x60e0
+#define MX28_PAD_EMI_BA0__EMI_BA0 0x6100
+#define MX28_PAD_EMI_BA1__EMI_BA1 0x6110
+#define MX28_PAD_EMI_BA2__EMI_BA2 0x6120
+#define MX28_PAD_EMI_CASN__EMI_CASN 0x6130
+#define MX28_PAD_EMI_RASN__EMI_RASN 0x6140
+#define MX28_PAD_EMI_WEN__EMI_WEN 0x6150
+#define MX28_PAD_EMI_CE0N__EMI_CE0N 0x6160
+#define MX28_PAD_EMI_CE1N__EMI_CE1N 0x6170
+#define MX28_PAD_EMI_CKE__EMI_CKE 0x6180
+#define MX28_PAD_GPMI_D00__SSP1_D0 0x0001
+#define MX28_PAD_GPMI_D01__SSP1_D1 0x0011
+#define MX28_PAD_GPMI_D02__SSP1_D2 0x0021
+#define MX28_PAD_GPMI_D03__SSP1_D3 0x0031
+#define MX28_PAD_GPMI_D04__SSP1_D4 0x0041
+#define MX28_PAD_GPMI_D05__SSP1_D5 0x0051
+#define MX28_PAD_GPMI_D06__SSP1_D6 0x0061
+#define MX28_PAD_GPMI_D07__SSP1_D7 0x0071
+#define MX28_PAD_GPMI_CE0N__SSP3_D0 0x0101
+#define MX28_PAD_GPMI_CE1N__SSP3_D3 0x0111
+#define MX28_PAD_GPMI_CE2N__CAN1_TX 0x0121
+#define MX28_PAD_GPMI_CE3N__CAN1_RX 0x0131
+#define MX28_PAD_GPMI_RDY0__SSP1_CARD_DETECT 0x0141
+#define MX28_PAD_GPMI_RDY1__SSP1_CMD 0x0151
+#define MX28_PAD_GPMI_RDY2__CAN0_TX 0x0161
+#define MX28_PAD_GPMI_RDY3__CAN0_RX 0x0171
+#define MX28_PAD_GPMI_RDN__SSP3_SCK 0x0181
+#define MX28_PAD_GPMI_WRN__SSP1_SCK 0x0191
+#define MX28_PAD_GPMI_ALE__SSP3_D1 0x01a1
+#define MX28_PAD_GPMI_CLE__SSP3_D2 0x01b1
+#define MX28_PAD_GPMI_RESETN__SSP3_CMD 0x01c1
+#define MX28_PAD_LCD_D03__ETM_DA8 0x1031
+#define MX28_PAD_LCD_D04__ETM_DA9 0x1041
+#define MX28_PAD_LCD_D08__ETM_DA3 0x1081
+#define MX28_PAD_LCD_D09__ETM_DA4 0x1091
+#define MX28_PAD_LCD_D20__ENET1_1588_EVENT2_OUT 0x1141
+#define MX28_PAD_LCD_D21__ENET1_1588_EVENT2_IN 0x1151
+#define MX28_PAD_LCD_D22__ENET1_1588_EVENT3_OUT 0x1161
+#define MX28_PAD_LCD_D23__ENET1_1588_EVENT3_IN 0x1171
+#define MX28_PAD_LCD_RD_E__LCD_VSYNC 0x1181
+#define MX28_PAD_LCD_WR_RWN__LCD_HSYNC 0x1191
+#define MX28_PAD_LCD_RS__LCD_DOTCLK 0x11a1
+#define MX28_PAD_LCD_CS__LCD_ENABLE 0x11b1
+#define MX28_PAD_LCD_VSYNC__SAIF1_SDATA0 0x11c1
+#define MX28_PAD_LCD_HSYNC__SAIF1_SDATA1 0x11d1
+#define MX28_PAD_LCD_DOTCLK__SAIF1_MCLK 0x11e1
+#define MX28_PAD_SSP0_DATA4__SSP2_D0 0x2041
+#define MX28_PAD_SSP0_DATA5__SSP2_D3 0x2051
+#define MX28_PAD_SSP0_DATA6__SSP2_CMD 0x2061
+#define MX28_PAD_SSP0_DATA7__SSP2_SCK 0x2071
+#define MX28_PAD_SSP1_SCK__SSP2_D1 0x20c1
+#define MX28_PAD_SSP1_CMD__SSP2_D2 0x20d1
+#define MX28_PAD_SSP1_DATA0__SSP2_D6 0x20e1
+#define MX28_PAD_SSP1_DATA3__SSP2_D7 0x20f1
+#define MX28_PAD_SSP2_SCK__AUART2_RX 0x2101
+#define MX28_PAD_SSP2_MOSI__AUART2_TX 0x2111
+#define MX28_PAD_SSP2_MISO__AUART3_RX 0x2121
+#define MX28_PAD_SSP2_SS0__AUART3_TX 0x2131
+#define MX28_PAD_SSP2_SS1__SSP2_D1 0x2141
+#define MX28_PAD_SSP2_SS2__SSP2_D2 0x2151
+#define MX28_PAD_SSP3_SCK__AUART4_TX 0x2181
+#define MX28_PAD_SSP3_MOSI__AUART4_RX 0x2191
+#define MX28_PAD_SSP3_MISO__AUART4_RTS 0x21a1
+#define MX28_PAD_SSP3_SS0__AUART4_CTS 0x21b1
+#define MX28_PAD_AUART0_RX__I2C0_SCL 0x3001
+#define MX28_PAD_AUART0_TX__I2C0_SDA 0x3011
+#define MX28_PAD_AUART0_CTS__AUART4_RX 0x3021
+#define MX28_PAD_AUART0_RTS__AUART4_TX 0x3031
+#define MX28_PAD_AUART1_RX__SSP2_CARD_DETECT 0x3041
+#define MX28_PAD_AUART1_TX__SSP3_CARD_DETECT 0x3051
+#define MX28_PAD_AUART1_CTS__USB0_OVERCURRENT 0x3061
+#define MX28_PAD_AUART1_RTS__USB0_ID 0x3071
+#define MX28_PAD_AUART2_RX__SSP3_D1 0x3081
+#define MX28_PAD_AUART2_TX__SSP3_D2 0x3091
+#define MX28_PAD_AUART2_CTS__I2C1_SCL 0x30a1
+#define MX28_PAD_AUART2_RTS__I2C1_SDA 0x30b1
+#define MX28_PAD_AUART3_RX__CAN0_TX 0x30c1
+#define MX28_PAD_AUART3_TX__CAN0_RX 0x30d1
+#define MX28_PAD_AUART3_CTS__CAN1_TX 0x30e1
+#define MX28_PAD_AUART3_RTS__CAN1_RX 0x30f1
+#define MX28_PAD_PWM0__I2C1_SCL 0x3101
+#define MX28_PAD_PWM1__I2C1_SDA 0x3111
+#define MX28_PAD_PWM2__USB0_ID 0x3121
+#define MX28_PAD_SAIF0_MCLK__PWM_3 0x3141
+#define MX28_PAD_SAIF0_LRCLK__PWM_4 0x3151
+#define MX28_PAD_SAIF0_BITCLK__PWM_5 0x3161
+#define MX28_PAD_SAIF0_SDATA0__PWM_6 0x3171
+#define MX28_PAD_I2C0_SCL__TIMROT_ROTARYA 0x3181
+#define MX28_PAD_I2C0_SDA__TIMROT_ROTARYB 0x3191
+#define MX28_PAD_SAIF1_SDATA0__PWM_7 0x31a1
+#define MX28_PAD_LCD_RESET__LCD_VSYNC 0x31e1
+#define MX28_PAD_ENET0_MDC__GPMI_CE4N 0x4001
+#define MX28_PAD_ENET0_MDIO__GPMI_CE5N 0x4011
+#define MX28_PAD_ENET0_RX_EN__GPMI_CE6N 0x4021
+#define MX28_PAD_ENET0_RXD0__GPMI_CE7N 0x4031
+#define MX28_PAD_ENET0_RXD1__GPMI_READY4 0x4041
+#define MX28_PAD_ENET0_TX_CLK__HSADC_TRIGGER 0x4051
+#define MX28_PAD_ENET0_TX_EN__GPMI_READY5 0x4061
+#define MX28_PAD_ENET0_TXD0__GPMI_READY6 0x4071
+#define MX28_PAD_ENET0_TXD1__GPMI_READY7 0x4081
+#define MX28_PAD_ENET0_RXD2__ENET1_RXD0 0x4091
+#define MX28_PAD_ENET0_RXD3__ENET1_RXD1 0x40a1
+#define MX28_PAD_ENET0_TXD2__ENET1_TXD0 0x40b1
+#define MX28_PAD_ENET0_TXD3__ENET1_TXD1 0x40c1
+#define MX28_PAD_ENET0_RX_CLK__ENET0_RX_ER 0x40d1
+#define MX28_PAD_ENET0_COL__ENET1_TX_EN 0x40e1
+#define MX28_PAD_ENET0_CRS__ENET1_RX_EN 0x40f1
+#define MX28_PAD_GPMI_CE2N__ENET0_RX_ER 0x0122
+#define MX28_PAD_GPMI_CE3N__SAIF1_MCLK 0x0132
+#define MX28_PAD_GPMI_RDY0__USB0_ID 0x0142
+#define MX28_PAD_GPMI_RDY2__ENET0_TX_ER 0x0162
+#define MX28_PAD_GPMI_RDY3__HSADC_TRIGGER 0x0172
+#define MX28_PAD_GPMI_ALE__SSP3_D4 0x01a2
+#define MX28_PAD_GPMI_CLE__SSP3_D5 0x01b2
+#define MX28_PAD_LCD_D00__ETM_DA0 0x1002
+#define MX28_PAD_LCD_D01__ETM_DA1 0x1012
+#define MX28_PAD_LCD_D02__ETM_DA2 0x1022
+#define MX28_PAD_LCD_D03__ETM_DA3 0x1032
+#define MX28_PAD_LCD_D04__ETM_DA4 0x1042
+#define MX28_PAD_LCD_D05__ETM_DA5 0x1052
+#define MX28_PAD_LCD_D06__ETM_DA6 0x1062
+#define MX28_PAD_LCD_D07__ETM_DA7 0x1072
+#define MX28_PAD_LCD_D08__ETM_DA8 0x1082
+#define MX28_PAD_LCD_D09__ETM_DA9 0x1092
+#define MX28_PAD_LCD_D10__ETM_DA10 0x10a2
+#define MX28_PAD_LCD_D11__ETM_DA11 0x10b2
+#define MX28_PAD_LCD_D12__ETM_DA12 0x10c2
+#define MX28_PAD_LCD_D13__ETM_DA13 0x10d2
+#define MX28_PAD_LCD_D14__ETM_DA14 0x10e2
+#define MX28_PAD_LCD_D15__ETM_DA15 0x10f2
+#define MX28_PAD_LCD_D16__ETM_DA7 0x1102
+#define MX28_PAD_LCD_D17__ETM_DA6 0x1112
+#define MX28_PAD_LCD_D18__ETM_DA5 0x1122
+#define MX28_PAD_LCD_D19__ETM_DA4 0x1132
+#define MX28_PAD_LCD_D20__ETM_DA3 0x1142
+#define MX28_PAD_LCD_D21__ETM_DA2 0x1152
+#define MX28_PAD_LCD_D22__ETM_DA1 0x1162
+#define MX28_PAD_LCD_D23__ETM_DA0 0x1172
+#define MX28_PAD_LCD_RD_E__ETM_TCTL 0x1182
+#define MX28_PAD_LCD_WR_RWN__ETM_TCLK 0x1192
+#define MX28_PAD_LCD_HSYNC__ETM_TCTL 0x11d2
+#define MX28_PAD_LCD_DOTCLK__ETM_TCLK 0x11e2
+#define MX28_PAD_SSP1_SCK__ENET0_1588_EVENT2_OUT 0x20c2
+#define MX28_PAD_SSP1_CMD__ENET0_1588_EVENT2_IN 0x20d2
+#define MX28_PAD_SSP1_DATA0__ENET0_1588_EVENT3_OUT 0x20e2
+#define MX28_PAD_SSP1_DATA3__ENET0_1588_EVENT3_IN 0x20f2
+#define MX28_PAD_SSP2_SCK__SAIF0_SDATA1 0x2102
+#define MX28_PAD_SSP2_MOSI__SAIF0_SDATA2 0x2112
+#define MX28_PAD_SSP2_MISO__SAIF1_SDATA1 0x2122
+#define MX28_PAD_SSP2_SS0__SAIF1_SDATA2 0x2132
+#define MX28_PAD_SSP2_SS1__USB1_OVERCURRENT 0x2142
+#define MX28_PAD_SSP2_SS2__USB0_OVERCURRENT 0x2152
+#define MX28_PAD_SSP3_SCK__ENET1_1588_EVENT0_OUT 0x2182
+#define MX28_PAD_SSP3_MOSI__ENET1_1588_EVENT0_IN 0x2192
+#define MX28_PAD_SSP3_MISO__ENET1_1588_EVENT1_OUT 0x21a2
+#define MX28_PAD_SSP3_SS0__ENET1_1588_EVENT1_IN 0x21b2
+#define MX28_PAD_AUART0_RX__DUART_CTS 0x3002
+#define MX28_PAD_AUART0_TX__DUART_RTS 0x3012
+#define MX28_PAD_AUART0_CTS__DUART_RX 0x3022
+#define MX28_PAD_AUART0_RTS__DUART_TX 0x3032
+#define MX28_PAD_AUART1_RX__PWM_0 0x3042
+#define MX28_PAD_AUART1_TX__PWM_1 0x3052
+#define MX28_PAD_AUART1_CTS__TIMROT_ROTARYA 0x3062
+#define MX28_PAD_AUART1_RTS__TIMROT_ROTARYB 0x3072
+#define MX28_PAD_AUART2_RX__SSP3_D4 0x3082
+#define MX28_PAD_AUART2_TX__SSP3_D5 0x3092
+#define MX28_PAD_AUART2_CTS__SAIF1_BITCLK 0x30a2
+#define MX28_PAD_AUART2_RTS__SAIF1_LRCLK 0x30b2
+#define MX28_PAD_AUART3_RX__ENET0_1588_EVENT0_OUT 0x30c2
+#define MX28_PAD_AUART3_TX__ENET0_1588_EVENT0_IN 0x30d2
+#define MX28_PAD_AUART3_CTS__ENET0_1588_EVENT1_OUT 0x30e2
+#define MX28_PAD_AUART3_RTS__ENET0_1588_EVENT1_IN 0x30f2
+#define MX28_PAD_PWM0__DUART_RX 0x3102
+#define MX28_PAD_PWM1__DUART_TX 0x3112
+#define MX28_PAD_PWM2__USB1_OVERCURRENT 0x3122
+#define MX28_PAD_SAIF0_MCLK__AUART4_CTS 0x3142
+#define MX28_PAD_SAIF0_LRCLK__AUART4_RTS 0x3152
+#define MX28_PAD_SAIF0_BITCLK__AUART4_RX 0x3162
+#define MX28_PAD_SAIF0_SDATA0__AUART4_TX 0x3172
+#define MX28_PAD_I2C0_SCL__DUART_RX 0x3182
+#define MX28_PAD_I2C0_SDA__DUART_TX 0x3192
+#define MX28_PAD_SAIF1_SDATA0__SAIF0_SDATA1 0x31a2
+#define MX28_PAD_SPDIF__ENET1_RX_ER 0x31b2
+#define MX28_PAD_ENET0_MDC__SAIF0_SDATA1 0x4002
+#define MX28_PAD_ENET0_MDIO__SAIF0_SDATA2 0x4012
+#define MX28_PAD_ENET0_RX_EN__SAIF1_SDATA1 0x4022
+#define MX28_PAD_ENET0_RXD0__SAIF1_SDATA2 0x4032
+#define MX28_PAD_ENET0_TX_CLK__ENET0_1588_EVENT2_OUT 0x4052
+#define MX28_PAD_ENET0_RXD2__ENET0_1588_EVENT0_OUT 0x4092
+#define MX28_PAD_ENET0_RXD3__ENET0_1588_EVENT0_IN 0x40a2
+#define MX28_PAD_ENET0_TXD2__ENET0_1588_EVENT1_OUT 0x40b2
+#define MX28_PAD_ENET0_TXD3__ENET0_1588_EVENT1_IN 0x40c2
+#define MX28_PAD_ENET0_RX_CLK__ENET0_1588_EVENT2_IN 0x40d2
+#define MX28_PAD_ENET0_COL__ENET0_1588_EVENT3_OUT 0x40e2
+#define MX28_PAD_ENET0_CRS__ENET0_1588_EVENT3_IN 0x40f2
+#define MX28_PAD_GPMI_D00__GPIO_0_0 0x0003
+#define MX28_PAD_GPMI_D01__GPIO_0_1 0x0013
+#define MX28_PAD_GPMI_D02__GPIO_0_2 0x0023
+#define MX28_PAD_GPMI_D03__GPIO_0_3 0x0033
+#define MX28_PAD_GPMI_D04__GPIO_0_4 0x0043
+#define MX28_PAD_GPMI_D05__GPIO_0_5 0x0053
+#define MX28_PAD_GPMI_D06__GPIO_0_6 0x0063
+#define MX28_PAD_GPMI_D07__GPIO_0_7 0x0073
+#define MX28_PAD_GPMI_CE0N__GPIO_0_16 0x0103
+#define MX28_PAD_GPMI_CE1N__GPIO_0_17 0x0113
+#define MX28_PAD_GPMI_CE2N__GPIO_0_18 0x0123
+#define MX28_PAD_GPMI_CE3N__GPIO_0_19 0x0133
+#define MX28_PAD_GPMI_RDY0__GPIO_0_20 0x0143
+#define MX28_PAD_GPMI_RDY1__GPIO_0_21 0x0153
+#define MX28_PAD_GPMI_RDY2__GPIO_0_22 0x0163
+#define MX28_PAD_GPMI_RDY3__GPIO_0_23 0x0173
+#define MX28_PAD_GPMI_RDN__GPIO_0_24 0x0183
+#define MX28_PAD_GPMI_WRN__GPIO_0_25 0x0193
+#define MX28_PAD_GPMI_ALE__GPIO_0_26 0x01a3
+#define MX28_PAD_GPMI_CLE__GPIO_0_27 0x01b3
+#define MX28_PAD_GPMI_RESETN__GPIO_0_28 0x01c3
+#define MX28_PAD_LCD_D00__GPIO_1_0 0x1003
+#define MX28_PAD_LCD_D01__GPIO_1_1 0x1013
+#define MX28_PAD_LCD_D02__GPIO_1_2 0x1023
+#define MX28_PAD_LCD_D03__GPIO_1_3 0x1033
+#define MX28_PAD_LCD_D04__GPIO_1_4 0x1043
+#define MX28_PAD_LCD_D05__GPIO_1_5 0x1053
+#define MX28_PAD_LCD_D06__GPIO_1_6 0x1063
+#define MX28_PAD_LCD_D07__GPIO_1_7 0x1073
+#define MX28_PAD_LCD_D08__GPIO_1_8 0x1083
+#define MX28_PAD_LCD_D09__GPIO_1_9 0x1093
+#define MX28_PAD_LCD_D10__GPIO_1_10 0x10a3
+#define MX28_PAD_LCD_D11__GPIO_1_11 0x10b3
+#define MX28_PAD_LCD_D12__GPIO_1_12 0x10c3
+#define MX28_PAD_LCD_D13__GPIO_1_13 0x10d3
+#define MX28_PAD_LCD_D14__GPIO_1_14 0x10e3
+#define MX28_PAD_LCD_D15__GPIO_1_15 0x10f3
+#define MX28_PAD_LCD_D16__GPIO_1_16 0x1103
+#define MX28_PAD_LCD_D17__GPIO_1_17 0x1113
+#define MX28_PAD_LCD_D18__GPIO_1_18 0x1123
+#define MX28_PAD_LCD_D19__GPIO_1_19 0x1133
+#define MX28_PAD_LCD_D20__GPIO_1_20 0x1143
+#define MX28_PAD_LCD_D21__GPIO_1_21 0x1153
+#define MX28_PAD_LCD_D22__GPIO_1_22 0x1163
+#define MX28_PAD_LCD_D23__GPIO_1_23 0x1173
+#define MX28_PAD_LCD_RD_E__GPIO_1_24 0x1183
+#define MX28_PAD_LCD_WR_RWN__GPIO_1_25 0x1193
+#define MX28_PAD_LCD_RS__GPIO_1_26 0x11a3
+#define MX28_PAD_LCD_CS__GPIO_1_27 0x11b3
+#define MX28_PAD_LCD_VSYNC__GPIO_1_28 0x11c3
+#define MX28_PAD_LCD_HSYNC__GPIO_1_29 0x11d3
+#define MX28_PAD_LCD_DOTCLK__GPIO_1_30 0x11e3
+#define MX28_PAD_LCD_ENABLE__GPIO_1_31 0x11f3
+#define MX28_PAD_SSP0_DATA0__GPIO_2_0 0x2003
+#define MX28_PAD_SSP0_DATA1__GPIO_2_1 0x2013
+#define MX28_PAD_SSP0_DATA2__GPIO_2_2 0x2023
+#define MX28_PAD_SSP0_DATA3__GPIO_2_3 0x2033
+#define MX28_PAD_SSP0_DATA4__GPIO_2_4 0x2043
+#define MX28_PAD_SSP0_DATA5__GPIO_2_5 0x2053
+#define MX28_PAD_SSP0_DATA6__GPIO_2_6 0x2063
+#define MX28_PAD_SSP0_DATA7__GPIO_2_7 0x2073
+#define MX28_PAD_SSP0_CMD__GPIO_2_8 0x2083
+#define MX28_PAD_SSP0_DETECT__GPIO_2_9 0x2093
+#define MX28_PAD_SSP0_SCK__GPIO_2_10 0x20a3
+#define MX28_PAD_SSP1_SCK__GPIO_2_12 0x20c3
+#define MX28_PAD_SSP1_CMD__GPIO_2_13 0x20d3
+#define MX28_PAD_SSP1_DATA0__GPIO_2_14 0x20e3
+#define MX28_PAD_SSP1_DATA3__GPIO_2_15 0x20f3
+#define MX28_PAD_SSP2_SCK__GPIO_2_16 0x2103
+#define MX28_PAD_SSP2_MOSI__GPIO_2_17 0x2113
+#define MX28_PAD_SSP2_MISO__GPIO_2_18 0x2123
+#define MX28_PAD_SSP2_SS0__GPIO_2_19 0x2133
+#define MX28_PAD_SSP2_SS1__GPIO_2_20 0x2143
+#define MX28_PAD_SSP2_SS2__GPIO_2_21 0x2153
+#define MX28_PAD_SSP3_SCK__GPIO_2_24 0x2183
+#define MX28_PAD_SSP3_MOSI__GPIO_2_25 0x2193
+#define MX28_PAD_SSP3_MISO__GPIO_2_26 0x21a3
+#define MX28_PAD_SSP3_SS0__GPIO_2_27 0x21b3
+#define MX28_PAD_AUART0_RX__GPIO_3_0 0x3003
+#define MX28_PAD_AUART0_TX__GPIO_3_1 0x3013
+#define MX28_PAD_AUART0_CTS__GPIO_3_2 0x3023
+#define MX28_PAD_AUART0_RTS__GPIO_3_3 0x3033
+#define MX28_PAD_AUART1_RX__GPIO_3_4 0x3043
+#define MX28_PAD_AUART1_TX__GPIO_3_5 0x3053
+#define MX28_PAD_AUART1_CTS__GPIO_3_6 0x3063
+#define MX28_PAD_AUART1_RTS__GPIO_3_7 0x3073
+#define MX28_PAD_AUART2_RX__GPIO_3_8 0x3083
+#define MX28_PAD_AUART2_TX__GPIO_3_9 0x3093
+#define MX28_PAD_AUART2_CTS__GPIO_3_10 0x30a3
+#define MX28_PAD_AUART2_RTS__GPIO_3_11 0x30b3
+#define MX28_PAD_AUART3_RX__GPIO_3_12 0x30c3
+#define MX28_PAD_AUART3_TX__GPIO_3_13 0x30d3
+#define MX28_PAD_AUART3_CTS__GPIO_3_14 0x30e3
+#define MX28_PAD_AUART3_RTS__GPIO_3_15 0x30f3
+#define MX28_PAD_PWM0__GPIO_3_16 0x3103
+#define MX28_PAD_PWM1__GPIO_3_17 0x3113
+#define MX28_PAD_PWM2__GPIO_3_18 0x3123
+#define MX28_PAD_SAIF0_MCLK__GPIO_3_20 0x3143
+#define MX28_PAD_SAIF0_LRCLK__GPIO_3_21 0x3153
+#define MX28_PAD_SAIF0_BITCLK__GPIO_3_22 0x3163
+#define MX28_PAD_SAIF0_SDATA0__GPIO_3_23 0x3173
+#define MX28_PAD_I2C0_SCL__GPIO_3_24 0x3183
+#define MX28_PAD_I2C0_SDA__GPIO_3_25 0x3193
+#define MX28_PAD_SAIF1_SDATA0__GPIO_3_26 0x31a3
+#define MX28_PAD_SPDIF__GPIO_3_27 0x31b3
+#define MX28_PAD_PWM3__GPIO_3_28 0x31c3
+#define MX28_PAD_PWM4__GPIO_3_29 0x31d3
+#define MX28_PAD_LCD_RESET__GPIO_3_30 0x31e3
+#define MX28_PAD_ENET0_MDC__GPIO_4_0 0x4003
+#define MX28_PAD_ENET0_MDIO__GPIO_4_1 0x4013
+#define MX28_PAD_ENET0_RX_EN__GPIO_4_2 0x4023
+#define MX28_PAD_ENET0_RXD0__GPIO_4_3 0x4033
+#define MX28_PAD_ENET0_RXD1__GPIO_4_4 0x4043
+#define MX28_PAD_ENET0_TX_CLK__GPIO_4_5 0x4053
+#define MX28_PAD_ENET0_TX_EN__GPIO_4_6 0x4063
+#define MX28_PAD_ENET0_TXD0__GPIO_4_7 0x4073
+#define MX28_PAD_ENET0_TXD1__GPIO_4_8 0x4083
+#define MX28_PAD_ENET0_RXD2__GPIO_4_9 0x4093
+#define MX28_PAD_ENET0_RXD3__GPIO_4_10 0x40a3
+#define MX28_PAD_ENET0_TXD2__GPIO_4_11 0x40b3
+#define MX28_PAD_ENET0_TXD3__GPIO_4_12 0x40c3
+#define MX28_PAD_ENET0_RX_CLK__GPIO_4_13 0x40d3
+#define MX28_PAD_ENET0_COL__GPIO_4_14 0x40e3
+#define MX28_PAD_ENET0_CRS__GPIO_4_15 0x40f3
+#define MX28_PAD_ENET_CLK__GPIO_4_16 0x4103
+#define MX28_PAD_JTAG_RTCK__GPIO_4_20 0x4143
+
+#endif /* __DT_BINDINGS_MX28_PINCTRL_H__ */
diff --git a/arch/arm/boot/dts/imx28-sps1.dts b/arch/arm/boot/dts/imx28-sps1.dts
index 6c6a544..4870f07 100644
--- a/arch/arm/boot/dts/imx28-sps1.dts
+++ b/arch/arm/boot/dts/imx28-sps1.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "SchulerControl GmbH, SC SPS 1";
@@ -29,13 +29,13 @@
hog_pins_a: hog-gpios@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0003 /* MX28_PAD_GPMI_D00__GPIO_0_0 */
- 0x0033 /* MX28_PAD_GPMI_D03__GPIO_0_3 */
- 0x0063 /* MX28_PAD_GPMI_D06__GPIO_0_6 */
+ MX28_PAD_GPMI_D00__GPIO_0_0
+ MX28_PAD_GPMI_D03__GPIO_0_3
+ MX28_PAD_GPMI_D06__GPIO_0_6
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-tx28.dts b/arch/arm/boot/dts/imx28-tx28.dts
index 37be532..be5a055 100644
--- a/arch/arm/boot/dts/imx28-tx28.dts
+++ b/arch/arm/boot/dts/imx28-tx28.dts
@@ -1,106 +1,139 @@
+/*
+ * Copyright 2012 Shawn Guo <shawn.guo@linaro.org>
+ * Copyright 2013 Lothar Waßmann <LW@KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "Ka-Ro electronics TX28 module";
compatible = "karo,tx28", "fsl,imx28";
+ aliases {
+ can0 = &can0;
+ can1 = &can1;
+ display = &display;
+ ds1339 = &ds1339;
+ gpio5 = &gpio5;
+ lcdif = &lcdif;
+ lcdif_23bit_pins = &tx28_lcdif_23bit_pins;
+ lcdif_24bit_pins = &lcdif_24bit_pins_a;
+ stk5led = &user_led;
+ usbotg = &usb0;
+ };
+
memory {
- reg = <0x40000000 0x08000000>;
+ reg = <0 0>; /* will be filled in by U-Boot */
};
- apb@80000000 {
- apbh@80000000 {
- ssp0: ssp@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_4bit_pins_a
- &mmc0_cd_cfg
- &mmc0_sck_cfg>;
- bus-width = <4>;
- status = "okay";
- };
+ onewire {
+ compatible = "w1-gpio";
+ gpios = <&gpio2 7 0>;
+ status = "disabled";
+ };
- pinctrl@80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
+ regulators {
+ compatible = "simple-bus";
- hog_pins_a: hog@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- 0x40a3 /* MX28_PAD_ENET0_RXD3__GPIO_4_10 */
- >;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
- };
-
- mac0_pins_gpio: mac0-gpio-mode@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- 0x4003 /* MX28_PAD_ENET0_MDC__GPIO_4_0 */
- 0x4013 /* MX28_PAD_ENET0_MDIO__GPIO_4_1 */
- 0x4023 /* MX28_PAD_ENET0_RX_EN__GPIO_4_2 */
- 0x4033 /* MX28_PAD_ENET0_RXD0__GPIO_4_3 */
- 0x4043 /* MX28_PAD_ENET0_RXD1__GPIO_4_4 */
- 0x4063 /* MX28_PAD_ENET0_TX_EN__GPIO_4_6 */
- 0x4073 /* MX28_PAD_ENET0_TXD0__GPIO_4_7 */
- 0x4083 /* MX28_PAD_ENET0_TXD1__GPIO_4_8 */
- 0x4103 /* MX28_PAD_ENET_CLK__GPIO_4_16 */
- >;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
- };
- };
+ reg_usb0_vbus: usb0_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb0_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio0 18 0>;
+ enable-active-high;
};
- apbx@80040000 {
- i2c0: i2c@80058000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
+ reg_usb1_vbus: usb1_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 27 0>;
+ enable-active-high;
+ };
- ds1339: rtc@68 {
- compatible = "mxim,ds1339";
- reg = <0x68>;
- };
- };
+ reg_2p5v: 2p5v {
+ compatible = "regulator-fixed";
+ regulator-name = "2P5V";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
- pwm: pwm@80064000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins_a>;
- status = "okay";
- };
+ reg_3p3v: 3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_4pins_a>;
- status = "okay";
- };
+ reg_can_xcvr: can-xcvr {
+ compatible = "regulator-fixed";
+ regulator-name = "CAN XCVR";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 0 0>;
+ enable-active-low;
+ pinctrl-names = "default";
+ pinctrl-0 = <&tx28_flexcan_xcvr_pins>;
+ };
- auart1: serial@8006c000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart1_pins_a>;
- status = "okay";
- };
+ reg_lcd: lcd-power {
+ compatible = "regulator-fixed";
+ regulator-name = "LCD POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 31 0>;
+ enable-active-high;
+ };
+
+ reg_lcd_reset: lcd-reset {
+ compatible = "regulator-fixed";
+ regulator-name = "LCD RESET";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 30 0>;
+ startup-delay-us = <300000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
};
};
- ahb@80080000 {
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default", "gpio_mode";
- pinctrl-0 = <&mac0_pins_a>;
- pinctrl-1 = <&mac0_pins_gpio>;
- status = "okay";
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ mclk: clock@0 {
+ compatible = "fixed-clock";
+ reg = <0>;
+ #clock-cells = <0>;
+ clock-frequency = <27000000>;
};
};
+ sound {
+ compatible = "fsl,imx28-tx28-sgtl5000",
+ "fsl,mxs-audio-sgtl5000";
+ model = "imx28-tx28-sgtl5000";
+ saif-controllers = <&saif0 &saif1>;
+ audio-codec = <&sgtl5000>;
+ };
+
leds {
compatible = "gpio-leds";
- user {
+ user_led: user {
label = "Heartbeat";
gpios = <&gpio4 10 0>;
linux,default-trigger = "heartbeat";
@@ -109,8 +142,512 @@
backlight {
compatible = "pwm-backlight";
- pwms = <&pwm 0 5000000>;
- brightness-levels = <0 4 8 16 32 64 128 255>;
- default-brightness-level = <6>;
+ pwms = <&pwm 0 500000>;
+ /*
+ * a silly way to create a 1:1 relationship between the
+ * PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
};
+
+ matrix_keypad: matrix-keypad@0 {
+ compatible = "gpio-matrix-keypad";
+ col-gpios = <
+ &gpio5 0 0
+ &gpio5 1 0
+ &gpio5 2 0
+ &gpio5 3 0
+ >;
+ row-gpios = <
+ &gpio5 4 0
+ &gpio5 5 0
+ &gpio5 6 0
+ &gpio5 7 0
+ >;
+ /* sample keymap */
+ linux,keymap = <
+ 0x00000074 /* row 0, col 0, KEY_POWER */
+ 0x00010052 /* row 0, col 1, KEY_KP0 */
+ 0x0002004f /* row 0, col 2, KEY_KP1 */
+ 0x00030050 /* row 0, col 3, KEY_KP2 */
+ 0x01000051 /* row 1, col 0, KEY_KP3 */
+ 0x0101004b /* row 1, col 1, KEY_KP4 */
+ 0x0102004c /* row 1, col 2, KEY_KP5 */
+ 0x0103004d /* row 1, col 3, KEY_KP6 */
+ 0x02000047 /* row 2, col 0, KEY_KP7 */
+ 0x02010048 /* row 2, col 1, KEY_KP8 */
+ 0x02020049 /* row 2, col 2, KEY_KP9 */
+ >;
+ gpio-activelow;
+ linux,wakeup;
+ debounce-delay-ms = <100>;
+ col-scan-delay-us = <5000>;
+ linux,no-autorepeat;
+ };
+};
+
+/* 2nd TX-Std UART - (A)UART1 */
+&auart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart1_pins_a>;
+ status = "okay";
+};
+
+/* 3rd TX-Std UART - (A)UART3 */
+&auart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart3_pins_a>;
+ status = "okay";
+};
+
+&can0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can0_pins_a>;
+ xceiver-supply = <®_can_xcvr>;
+ status = "okay";
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can1_pins_a>;
+ xceiver-supply = <®_can_xcvr>;
+ status = "okay";
+};
+
+&digctl {
+ status = "okay";
+};
+
+/* 1st TX-Std UART - (D)UART */
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_4pins_a>;
+ status = "okay";
+};
+
+&gpmi {
+ pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+ nand-on-flash-bbt;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ sgtl5000: sgtl5000@0a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ VDDA-supply = <®_2p5v>;
+ VDDIO-supply = <®_3p3v>;
+ clocks = <&mclk>;
+ };
+
+ gpio5: pca953x@20 {
+ compatible = "nxp,pca9554";
+ reg = <0x20>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&tx28_pca9554_pins>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <28 0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ polytouch: edt-ft5x06@38 {
+ compatible = "edt,edt-ft5x06";
+ reg = <0x38>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&tx28_edt_ft5x06_pins>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <5 0>;
+ reset-gpios = <&gpio2 6 1>;
+ wake-gpios = <&gpio4 9 0>;
+ };
+
+ touchscreen: tsc2007@48 {
+ compatible = "ti,tsc2007";
+ reg = <0x48>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&tx28_tsc2007_pins>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <20 0>;
+ pendown-gpio = <&gpio3 20 1>;
+ ti,x-plate-ohms = /bits/ 16 <660>;
+ };
+
+ ds1339: rtc@68 {
+ compatible = "mxim,ds1339";
+ reg = <0x68>;
+ };
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_24bit_pins_a &lcdif_sync_pins_a &tx28_lcdif_ctrl_pins>;
+ lcd-supply = <®_lcd>;
+ display = <&display>;
+ status = "okay";
+
+ display: display@0 {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+ display-timings {
+ native-mode = <&timing5>;
+ timing0: timing0 {
+ panel-name = "VGA";
+ clock-frequency = <25175000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ timing1: timing1 {
+ panel-name = "ETV570";
+ clock-frequency = <25175000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ timing2: timing2 {
+ panel-name = "ET0350";
+ clock-frequency = <6500000>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ timing3: timing3 {
+ panel-name = "ET0430";
+ clock-frequency = <9000000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ timing4: timing4 {
+ panel-name = "ET0500", "ET0700";
+ clock-frequency = <33260000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ timing5: timing5 {
+ panel-name = "ETQ570";
+ clock-frequency = <6400000>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&lradc {
+ fsl,lradc-touchscreen-wires = <4>;
+ status = "okay";
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default", "gpio_mode";
+ pinctrl-0 = <&mac0_pins_a>;
+ pinctrl-1 = <&tx28_mac0_pins_gpio>;
+ status = "okay";
+};
+
+&mac1 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac1_pins_a>;
+ /* not enabled by default */
+};
+
+&mxs_rtc {
+ status = "okay";
+};
+
+&ocotp {
+ status = "okay";
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins_a>;
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_ENET0_RXD3__GPIO_4_10 /* module LED */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ tx28_edt_ft5x06_pins: tx28-edt-ft5x06-pins {
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP0_DATA6__GPIO_2_6 /* RESET */
+ MX28_PAD_SSP0_DATA5__GPIO_2_5 /* IRQ */
+ MX28_PAD_ENET0_RXD2__GPIO_4_9 /* WAKE */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ tx28_flexcan_xcvr_pins: tx28-flexcan-xcvr-pins {
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D00__GPIO_1_0
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ tx28_lcdif_23bit_pins: tx28-lcdif-23bit {
+ fsl,pinmux-ids = <
+ /* LCD_D00 may be used as Flexcan Transceiver Enable on STK5-V5 */
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
+ MX28_PAD_LCD_D18__LCD_D18
+ MX28_PAD_LCD_D19__LCD_D19
+ MX28_PAD_LCD_D20__LCD_D20
+ MX28_PAD_LCD_D21__LCD_D21
+ MX28_PAD_LCD_D22__LCD_D22
+ MX28_PAD_LCD_D23__LCD_D23
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ tx28_lcdif_ctrl_pins: tx28-lcdif-ctrl {
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_ENABLE__GPIO_1_31 /* Enable */
+ MX28_PAD_LCD_RESET__GPIO_3_30 /* Reset */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ tx28_mac0_pins_gpio: tx28-mac0-gpio-pins {
+ fsl,pinmux-ids = <
+ MX28_PAD_ENET0_MDC__GPIO_4_0
+ MX28_PAD_ENET0_MDIO__GPIO_4_1
+ MX28_PAD_ENET0_RX_EN__GPIO_4_2
+ MX28_PAD_ENET0_RXD0__GPIO_4_3
+ MX28_PAD_ENET0_RXD1__GPIO_4_4
+ MX28_PAD_ENET0_TX_EN__GPIO_4_6
+ MX28_PAD_ENET0_TXD0__GPIO_4_7
+ MX28_PAD_ENET0_TXD1__GPIO_4_8
+ MX28_PAD_ENET_CLK__GPIO_4_16
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ tx28_pca9554_pins: tx28-pca9554-pins {
+ fsl,pinmux-ids = <
+ MX28_PAD_PWM3__GPIO_3_28
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ tx28_tsc2007_pins: tx28-tsc2007-pins {
+ fsl,pinmux-ids = <
+ MX28_PAD_SAIF0_MCLK__GPIO_3_20 /* TSC2007 IRQ */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+
+ tx28_usbphy0_pins: tx28-usbphy0-pins {
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_CE2N__GPIO_0_18 /* USBOTG_VBUSEN */
+ MX28_PAD_GPMI_CE3N__GPIO_0_19 /* USBOTH_OC */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ tx28_usbphy1_pins: tx28-usbphy1-pins {
+ fsl,pinmux-ids = <
+ MX28_PAD_SPDIF__GPIO_3_27 /* USBH_VBUSEN */
+ MX28_PAD_JTAG_RTCK__GPIO_4_20 /* USBH_OC */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+&saif0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif0_pins_b>;
+ fsl,saif-master;
+ status = "okay";
+};
+
+&saif1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif1_pins_a>;
+ status = "okay";
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default", "special";
+ pinctrl-0 = <&mmc0_4bit_pins_a
+ &mmc0_cd_cfg
+ &mmc0_sck_cfg>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&ssp3 {
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi3_pins_a>;
+ clock-frequency = <57600000>;
+ status = "okay";
+
+ spidev0: spi@0 {
+ compatible = "spidev";
+ reg = <0>;
+ spi-max-frequency = <57600000>;
+ };
+
+ spidev1: spi@1 {
+ compatible = "spidev";
+ reg = <1>;
+ spi-max-frequency = <57600000>;
+ };
+};
+
+&usb0 {
+ vbus-supply = <®_usb0_vbus>;
+ disable-over-current;
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usb1 {
+ vbus-supply = <®_usb1_vbus>;
+ disable-over-current;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&tx28_usbphy0_pins>;
+ phy_type = "utmi";
+ status = "okay";
+};
+
+&usbphy1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&tx28_usbphy1_pins>;
+ phy_type = "utmi";
+ status = "okay";
};
diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
index 7363fde..1c5ed9d 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/imx28.dtsi
@@ -9,7 +9,8 @@
* http://www.gnu.org/copyleft/gpl.html
*/
-/include/ "skeleton.dtsi"
+#include "skeleton.dtsi"
+#include "imx28-pinfunc.h"
/ {
interrupt-parent = <&icoll>;
@@ -207,538 +208,579 @@
duart_pins_a: duart@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3102 /* MX28_PAD_PWM0__DUART_RX */
- 0x3112 /* MX28_PAD_PWM1__DUART_TX */
+ MX28_PAD_PWM0__DUART_RX
+ MX28_PAD_PWM1__DUART_TX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
duart_pins_b: duart@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x3022 /* MX28_PAD_AUART0_CTS__DUART_RX */
- 0x3032 /* MX28_PAD_AUART0_RTS__DUART_TX */
+ MX28_PAD_AUART0_CTS__DUART_RX
+ MX28_PAD_AUART0_RTS__DUART_TX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
duart_4pins_a: duart-4pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3022 /* MX28_PAD_AUART0_CTS__DUART_RX */
- 0x3032 /* MX28_PAD_AUART0_RTS__DUART_TX */
- 0x3002 /* MX28_PAD_AUART0_RX__DUART_CTS */
- 0x3012 /* MX28_PAD_AUART0_TX__DUART_RTS */
+ MX28_PAD_AUART0_CTS__DUART_RX
+ MX28_PAD_AUART0_RTS__DUART_TX
+ MX28_PAD_AUART0_RX__DUART_CTS
+ MX28_PAD_AUART0_TX__DUART_RTS
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
gpmi_pins_a: gpmi-nand@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0000 /* MX28_PAD_GPMI_D00__GPMI_D0 */
- 0x0010 /* MX28_PAD_GPMI_D01__GPMI_D1 */
- 0x0020 /* MX28_PAD_GPMI_D02__GPMI_D2 */
- 0x0030 /* MX28_PAD_GPMI_D03__GPMI_D3 */
- 0x0040 /* MX28_PAD_GPMI_D04__GPMI_D4 */
- 0x0050 /* MX28_PAD_GPMI_D05__GPMI_D5 */
- 0x0060 /* MX28_PAD_GPMI_D06__GPMI_D6 */
- 0x0070 /* MX28_PAD_GPMI_D07__GPMI_D7 */
- 0x0100 /* MX28_PAD_GPMI_CE0N__GPMI_CE0N */
- 0x0140 /* MX28_PAD_GPMI_RDY0__GPMI_READY0 */
- 0x0180 /* MX28_PAD_GPMI_RDN__GPMI_RDN */
- 0x0190 /* MX28_PAD_GPMI_WRN__GPMI_WRN */
- 0x01a0 /* MX28_PAD_GPMI_ALE__GPMI_ALE */
- 0x01b0 /* MX28_PAD_GPMI_CLE__GPMI_CLE */
- 0x01c0 /* MX28_PAD_GPMI_RESETN__GPMI_RESETN */
+ MX28_PAD_GPMI_D00__GPMI_D0
+ MX28_PAD_GPMI_D01__GPMI_D1
+ MX28_PAD_GPMI_D02__GPMI_D2
+ MX28_PAD_GPMI_D03__GPMI_D3
+ MX28_PAD_GPMI_D04__GPMI_D4
+ MX28_PAD_GPMI_D05__GPMI_D5
+ MX28_PAD_GPMI_D06__GPMI_D6
+ MX28_PAD_GPMI_D07__GPMI_D7
+ MX28_PAD_GPMI_CE0N__GPMI_CE0N
+ MX28_PAD_GPMI_RDY0__GPMI_READY0
+ MX28_PAD_GPMI_RDN__GPMI_RDN
+ MX28_PAD_GPMI_WRN__GPMI_WRN
+ MX28_PAD_GPMI_ALE__GPMI_ALE
+ MX28_PAD_GPMI_CLE__GPMI_CLE
+ MX28_PAD_GPMI_RESETN__GPMI_RESETN
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
gpmi_status_cfg: gpmi-status-cfg {
fsl,pinmux-ids = <
- 0x0180 /* MX28_PAD_GPMI_RDN__GPMI_RDN */
- 0x0190 /* MX28_PAD_GPMI_WRN__GPMI_WRN */
- 0x01c0 /* MX28_PAD_GPMI_RESETN__GPMI_RESETN */
+ MX28_PAD_GPMI_RDN__GPMI_RDN
+ MX28_PAD_GPMI_WRN__GPMI_WRN
+ MX28_PAD_GPMI_RESETN__GPMI_RESETN
>;
- fsl,drive-strength = <2>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
};
auart0_pins_a: auart0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3000 /* MX28_PAD_AUART0_RX__AUART0_RX */
- 0x3010 /* MX28_PAD_AUART0_TX__AUART0_TX */
- 0x3020 /* MX28_PAD_AUART0_CTS__AUART0_CTS */
- 0x3030 /* MX28_PAD_AUART0_RTS__AUART0_RTS */
+ MX28_PAD_AUART0_RX__AUART0_RX
+ MX28_PAD_AUART0_TX__AUART0_TX
+ MX28_PAD_AUART0_CTS__AUART0_CTS
+ MX28_PAD_AUART0_RTS__AUART0_RTS
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart0_2pins_a: auart0-2pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3000 /* MX28_PAD_AUART0_RX__AUART0_RX */
- 0x3010 /* MX28_PAD_AUART0_TX__AUART0_TX */
+ MX28_PAD_AUART0_RX__AUART0_RX
+ MX28_PAD_AUART0_TX__AUART0_TX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart1_pins_a: auart1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3040 /* MX28_PAD_AUART1_RX__AUART1_RX */
- 0x3050 /* MX28_PAD_AUART1_TX__AUART1_TX */
- 0x3060 /* MX28_PAD_AUART1_CTS__AUART1_CTS */
- 0x3070 /* MX28_PAD_AUART1_RTS__AUART1_RTS */
+ MX28_PAD_AUART1_RX__AUART1_RX
+ MX28_PAD_AUART1_TX__AUART1_TX
+ MX28_PAD_AUART1_CTS__AUART1_CTS
+ MX28_PAD_AUART1_RTS__AUART1_RTS
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart1_2pins_a: auart1-2pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3040 /* MX28_PAD_AUART1_RX__AUART1_RX */
- 0x3050 /* MX28_PAD_AUART1_TX__AUART1_TX */
+ MX28_PAD_AUART1_RX__AUART1_RX
+ MX28_PAD_AUART1_TX__AUART1_TX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart2_2pins_a: auart2-2pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2101 /* MX28_PAD_SSP2_SCK__AUART2_RX */
- 0x2111 /* MX28_PAD_SSP2_MOSI__AUART2_TX */
+ MX28_PAD_SSP2_SCK__AUART2_RX
+ MX28_PAD_SSP2_MOSI__AUART2_TX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart2_2pins_b: auart2-2pins@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x3080 /* MX28_PAD_AUART2_RX__AUART2_RX */
- 0x3090 /* MX28_PAD_AUART2_TX__AUART2_TX */
+ MX28_PAD_AUART2_RX__AUART2_RX
+ MX28_PAD_AUART2_TX__AUART2_TX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart3_pins_a: auart3@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x30c0 /* MX28_PAD_AUART3_RX__AUART3_RX */
- 0x30d0 /* MX28_PAD_AUART3_TX__AUART3_TX */
- 0x30e0 /* MX28_PAD_AUART3_CTS__AUART3_CTS */
- 0x30f0 /* MX28_PAD_AUART3_RTS__AUART3_RTS */
+ MX28_PAD_AUART3_RX__AUART3_RX
+ MX28_PAD_AUART3_TX__AUART3_TX
+ MX28_PAD_AUART3_CTS__AUART3_CTS
+ MX28_PAD_AUART3_RTS__AUART3_RTS
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart3_2pins_a: auart3-2pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2121 /* MX28_PAD_SSP2_MISO__AUART3_RX */
- 0x2131 /* MX28_PAD_SSP2_SS0__AUART3_TX */
+ MX28_PAD_SSP2_MISO__AUART3_RX
+ MX28_PAD_SSP2_SS0__AUART3_TX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart3_2pins_b: auart3-2pins@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x30c0 /* MX28_PAD_AUART3_RX__AUART3_RX */
- 0x30d0 /* MX28_PAD_AUART3_TX__AUART3_TX */
+ MX28_PAD_AUART3_RX__AUART3_RX
+ MX28_PAD_AUART3_TX__AUART3_TX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart4_2pins_a: auart4@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2181 /* MX28_PAD_SSP3_SCK__AUART4_TX */
- 0x2191 /* MX28_PAD_SSP3_MOSI__AUART4_RX */
+ MX28_PAD_SSP3_SCK__AUART4_TX
+ MX28_PAD_SSP3_MOSI__AUART4_RX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
mac0_pins_a: mac0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x4000 /* MX28_PAD_ENET0_MDC__ENET0_MDC */
- 0x4010 /* MX28_PAD_ENET0_MDIO__ENET0_MDIO */
- 0x4020 /* MX28_PAD_ENET0_RX_EN__ENET0_RX_EN */
- 0x4030 /* MX28_PAD_ENET0_RXD0__ENET0_RXD0 */
- 0x4040 /* MX28_PAD_ENET0_RXD1__ENET0_RXD1 */
- 0x4060 /* MX28_PAD_ENET0_TX_EN__ENET0_TX_EN */
- 0x4070 /* MX28_PAD_ENET0_TXD0__ENET0_TXD0 */
- 0x4080 /* MX28_PAD_ENET0_TXD1__ENET0_TXD1 */
- 0x4100 /* MX28_PAD_ENET_CLK__CLKCTRL_ENET */
+ MX28_PAD_ENET0_MDC__ENET0_MDC
+ MX28_PAD_ENET0_MDIO__ENET0_MDIO
+ MX28_PAD_ENET0_RX_EN__ENET0_RX_EN
+ MX28_PAD_ENET0_RXD0__ENET0_RXD0
+ MX28_PAD_ENET0_RXD1__ENET0_RXD1
+ MX28_PAD_ENET0_TX_EN__ENET0_TX_EN
+ MX28_PAD_ENET0_TXD0__ENET0_TXD0
+ MX28_PAD_ENET0_TXD1__ENET0_TXD1
+ MX28_PAD_ENET_CLK__CLKCTRL_ENET
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
mac1_pins_a: mac1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x40f1 /* MX28_PAD_ENET0_CRS__ENET1_RX_EN */
- 0x4091 /* MX28_PAD_ENET0_RXD2__ENET1_RXD0 */
- 0x40a1 /* MX28_PAD_ENET0_RXD3__ENET1_RXD1 */
- 0x40e1 /* MX28_PAD_ENET0_COL__ENET1_TX_EN */
- 0x40b1 /* MX28_PAD_ENET0_TXD2__ENET1_TXD0 */
- 0x40c1 /* MX28_PAD_ENET0_TXD3__ENET1_TXD1 */
+ MX28_PAD_ENET0_CRS__ENET1_RX_EN
+ MX28_PAD_ENET0_RXD2__ENET1_RXD0
+ MX28_PAD_ENET0_RXD3__ENET1_RXD1
+ MX28_PAD_ENET0_COL__ENET1_TX_EN
+ MX28_PAD_ENET0_TXD2__ENET1_TXD0
+ MX28_PAD_ENET0_TXD3__ENET1_TXD1
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
mmc0_8bit_pins_a: mmc0-8bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2000 /* MX28_PAD_SSP0_DATA0__SSP0_D0 */
- 0x2010 /* MX28_PAD_SSP0_DATA1__SSP0_D1 */
- 0x2020 /* MX28_PAD_SSP0_DATA2__SSP0_D2 */
- 0x2030 /* MX28_PAD_SSP0_DATA3__SSP0_D3 */
- 0x2040 /* MX28_PAD_SSP0_DATA4__SSP0_D4 */
- 0x2050 /* MX28_PAD_SSP0_DATA5__SSP0_D5 */
- 0x2060 /* MX28_PAD_SSP0_DATA6__SSP0_D6 */
- 0x2070 /* MX28_PAD_SSP0_DATA7__SSP0_D7 */
- 0x2080 /* MX28_PAD_SSP0_CMD__SSP0_CMD */
- 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */
- 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */
+ MX28_PAD_SSP0_DATA0__SSP0_D0
+ MX28_PAD_SSP0_DATA1__SSP0_D1
+ MX28_PAD_SSP0_DATA2__SSP0_D2
+ MX28_PAD_SSP0_DATA3__SSP0_D3
+ MX28_PAD_SSP0_DATA4__SSP0_D4
+ MX28_PAD_SSP0_DATA5__SSP0_D5
+ MX28_PAD_SSP0_DATA6__SSP0_D6
+ MX28_PAD_SSP0_DATA7__SSP0_D7
+ MX28_PAD_SSP0_CMD__SSP0_CMD
+ MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT
+ MX28_PAD_SSP0_SCK__SSP0_SCK
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
mmc0_4bit_pins_a: mmc0-4bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2000 /* MX28_PAD_SSP0_DATA0__SSP0_D0 */
- 0x2010 /* MX28_PAD_SSP0_DATA1__SSP0_D1 */
- 0x2020 /* MX28_PAD_SSP0_DATA2__SSP0_D2 */
- 0x2030 /* MX28_PAD_SSP0_DATA3__SSP0_D3 */
- 0x2080 /* MX28_PAD_SSP0_CMD__SSP0_CMD */
- 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */
- 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */
+ MX28_PAD_SSP0_DATA0__SSP0_D0
+ MX28_PAD_SSP0_DATA1__SSP0_D1
+ MX28_PAD_SSP0_DATA2__SSP0_D2
+ MX28_PAD_SSP0_DATA3__SSP0_D3
+ MX28_PAD_SSP0_CMD__SSP0_CMD
+ MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT
+ MX28_PAD_SSP0_SCK__SSP0_SCK
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
mmc0_cd_cfg: mmc0-cd-cfg {
fsl,pinmux-ids = <
- 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */
+ MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT
>;
- fsl,pull-up = <0>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
mmc0_sck_cfg: mmc0-sck-cfg {
fsl,pinmux-ids = <
- 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */
+ MX28_PAD_SSP0_SCK__SSP0_SCK
>;
- fsl,drive-strength = <2>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mmc2_4bit_pins_a: mmc2-4bit@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP0_DATA4__SSP2_D0
+ MX28_PAD_SSP1_SCK__SSP2_D1
+ MX28_PAD_SSP1_CMD__SSP2_D2
+ MX28_PAD_SSP0_DATA5__SSP2_D3
+ MX28_PAD_SSP0_DATA6__SSP2_CMD
+ MX28_PAD_AUART1_RX__SSP2_CARD_DETECT
+ MX28_PAD_SSP0_DATA7__SSP2_SCK
+ >;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ mmc2_cd_cfg: mmc2-cd-cfg {
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART1_RX__SSP2_CARD_DETECT
+ >;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mmc2_sck_cfg: mmc2-sck-cfg {
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP0_DATA7__SSP2_SCK
+ >;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
i2c0_pins_a: i2c0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3180 /* MX28_PAD_I2C0_SCL__I2C0_SCL */
- 0x3190 /* MX28_PAD_I2C0_SDA__I2C0_SDA */
+ MX28_PAD_I2C0_SCL__I2C0_SCL
+ MX28_PAD_I2C0_SDA__I2C0_SDA
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
i2c0_pins_b: i2c0@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x3001 /* MX28_PAD_AUART0_RX__I2C0_SCL */
- 0x3011 /* MX28_PAD_AUART0_TX__I2C0_SDA */
+ MX28_PAD_AUART0_RX__I2C0_SCL
+ MX28_PAD_AUART0_TX__I2C0_SDA
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
i2c1_pins_a: i2c1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3101 /* MX28_PAD_PWM0__I2C1_SCL */
- 0x3111 /* MX28_PAD_PWM1__I2C1_SDA */
+ MX28_PAD_PWM0__I2C1_SCL
+ MX28_PAD_PWM1__I2C1_SDA
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
saif0_pins_a: saif0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3140 /* MX28_PAD_SAIF0_MCLK__SAIF0_MCLK */
- 0x3150 /* MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK */
- 0x3160 /* MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK */
- 0x3170 /* MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 */
+ MX28_PAD_SAIF0_MCLK__SAIF0_MCLK
+ MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK
+ MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK
+ MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0
>;
- fsl,drive-strength = <2>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
saif0_pins_b: saif0@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x3150 /* MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK */
- 0x3160 /* MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK */
- 0x3170 /* MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 */
+ MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK
+ MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK
+ MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0
>;
- fsl,drive-strength = <2>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
saif1_pins_a: saif1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31a0 /* MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 */
+ MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0
>;
- fsl,drive-strength = <2>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
pwm0_pins_a: pwm0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3100 /* MX28_PAD_PWM0__PWM_0 */
+ MX28_PAD_PWM0__PWM_0
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
pwm2_pins_a: pwm2@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3120 /* MX28_PAD_PWM2__PWM_2 */
+ MX28_PAD_PWM2__PWM_2
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
pwm3_pins_a: pwm3@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31c0 /* MX28_PAD_PWM3__PWM_3 */
+ MX28_PAD_PWM3__PWM_3
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
pwm3_pins_b: pwm3@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x3141 /* MX28_PAD_SAIF0_MCLK__PWM3 */
+ MX28_PAD_SAIF0_MCLK__PWM_3
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
pwm4_pins_a: pwm4@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31d0 /* MX28_PAD_PWM4__PWM_4 */
+ MX28_PAD_PWM4__PWM_4
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_24bit_pins_a: lcdif-24bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */
- 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */
- 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */
- 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */
- 0x1120 /* MX28_PAD_LCD_D18__LCD_D18 */
- 0x1130 /* MX28_PAD_LCD_D19__LCD_D19 */
- 0x1140 /* MX28_PAD_LCD_D20__LCD_D20 */
- 0x1150 /* MX28_PAD_LCD_D21__LCD_D21 */
- 0x1160 /* MX28_PAD_LCD_D22__LCD_D22 */
- 0x1170 /* MX28_PAD_LCD_D23__LCD_D23 */
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
+ MX28_PAD_LCD_D18__LCD_D18
+ MX28_PAD_LCD_D19__LCD_D19
+ MX28_PAD_LCD_D20__LCD_D20
+ MX28_PAD_LCD_D21__LCD_D21
+ MX28_PAD_LCD_D22__LCD_D22
+ MX28_PAD_LCD_D23__LCD_D23
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_16bit_pins_a: lcdif-16bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */
- 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_sync_pins_a: lcdif-sync@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
can0_pins_a: can0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0161 /* MX28_PAD_GPMI_RDY2__CAN0_TX */
- 0x0171 /* MX28_PAD_GPMI_RDY3__CAN0_RX */
+ MX28_PAD_GPMI_RDY2__CAN0_TX
+ MX28_PAD_GPMI_RDY3__CAN0_RX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
can1_pins_a: can1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0121 /* MX28_PAD_GPMI_CE2N__CAN1_TX */
- 0x0131 /* MX28_PAD_GPMI_CE3N__CAN1_RX */
+ MX28_PAD_GPMI_CE2N__CAN1_TX
+ MX28_PAD_GPMI_CE3N__CAN1_RX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
spi2_pins_a: spi2@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2100 /* MX28_PAD_SSP2_SCK__SSP2_SCK */
- 0x2110 /* MX28_PAD_SSP2_MOSI__SSP2_CMD */
- 0x2120 /* MX28_PAD_SSP2_MISO__SSP2_D0 */
- 0x2130 /* MX28_PAD_SSP2_SS0__SSP2_D3 */
+ MX28_PAD_SSP2_SCK__SSP2_SCK
+ MX28_PAD_SSP2_MOSI__SSP2_CMD
+ MX28_PAD_SSP2_MISO__SSP2_D0
+ MX28_PAD_SSP2_SS0__SSP2_D3
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
spi3_pins_a: spi3@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3082 /* MX28_PAD_AUART2_RX__SSP3_D4 */
- 0x3092 /* MX28_PAD_AUART2_TX__SSP3_D5 */
- 0x2180 /* MX28_PAD_SSP3_SCK__SSP3_SCK */
- 0x2190 /* MX28_PAD_SSP3_MOSI__SSP3_CMD */
- 0x21A0 /* MX28_PAD_SSP3_MISO__SSP3_D0 */
- 0x21B0 /* MX28_PAD_SSP3_SS0__SSP3_D3 */
+ MX28_PAD_AUART2_RX__SSP3_D4
+ MX28_PAD_AUART2_TX__SSP3_D5
+ MX28_PAD_SSP3_SCK__SSP3_SCK
+ MX28_PAD_SSP3_MOSI__SSP3_CMD
+ MX28_PAD_SSP3_MISO__SSP3_D0
+ MX28_PAD_SSP3_SS0__SSP3_D3
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
usbphy0_pins_a: usbphy0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2152 /* MX28_PAD_SSP2_SS2__USB0_OVERCURRENT */
+ MX28_PAD_SSP2_SS2__USB0_OVERCURRENT
>;
- fsl,drive-strength = <2>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
usbphy0_pins_b: usbphy0@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x3061 /* MX28_PAD_AUART1_CTS__USB0_OVERCURRENT */
+ MX28_PAD_AUART1_CTS__USB0_OVERCURRENT
>;
- fsl,drive-strength = <2>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
usbphy1_pins_a: usbphy1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2142 /* MX28_PAD_SSP2_SS1__USB1_OVERCURRENT */
+ MX28_PAD_SSP2_SS1__USB1_OVERCURRENT
>;
- fsl,drive-strength = <2>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ usb0_id_pins_a: usb0id@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART1_RTS__USB0_ID
+ >;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx51-apf51dev.dts b/arch/arm/boot/dts/imx51-apf51dev.dts
index 123fe84..5a7f552 100644
--- a/arch/arm/boot/dts/imx51-apf51dev.dts
+++ b/arch/arm/boot/dts/imx51-apf51dev.dts
@@ -16,6 +16,33 @@
model = "Armadeus Systems APF51Dev docking/development board";
compatible = "armadeus,imx51-apf51dev", "armadeus,imx51-apf51", "fsl,imx51";
+ display@di1 {
+ compatible = "fsl,imx-parallel-display";
+ crtcs = <&ipu 0>;
+ interface-pix-fmt = "bgr666";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu_disp1_1>;
+
+ display-timings {
+ lw700 {
+ native-mode;
+ clock-frequency = <33000033>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <96>;
+ hfront-porch = <96>;
+ vback-porch = <20>;
+ vfront-porch = <21>;
+ hsync-len = <64>;
+ vsync-len = <4>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+
gpio-keys {
compatible = "gpio-keys";
diff --git a/arch/arm/boot/dts/imx51-babbage.dts b/arch/arm/boot/dts/imx51-babbage.dts
index 1d337d9..be1407c 100644
--- a/arch/arm/boot/dts/imx51-babbage.dts
+++ b/arch/arm/boot/dts/imx51-babbage.dts
@@ -27,6 +27,20 @@
interface-pix-fmt = "rgb24";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ipu_disp1_1>;
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: dvi {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ };
+ };
};
display@di1 {
@@ -35,6 +49,25 @@
interface-pix-fmt = "rgb565";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ipu_disp2_1>;
+ status = "disabled";
+ display-timings {
+ native-mode = <&timing1>;
+ timing1: claawvga {
+ clock-frequency = <27000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <40>;
+ hfront-porch = <60>;
+ vback-porch = <10>;
+ vfront-porch = <10>;
+ hsync-len = <20>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
};
gpio-keys {
@@ -95,7 +128,7 @@
&uart3 {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart3_1>;
+ pinctrl-0 = <&pinctrl_uart3_1 &pinctrl_uart3_rtscts_1>;
fsl,uart-has-rtscts;
status = "okay";
};
@@ -252,7 +285,7 @@
&uart1 {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1_1>;
+ pinctrl-0 = <&pinctrl_uart1_1 &pinctrl_uart1_rtscts_1>;
fsl,uart-has-rtscts;
status = "okay";
};
diff --git a/arch/arm/boot/dts/imx51.dtsi b/arch/arm/boot/dts/imx51.dtsi
index 54cee65..f4dcff3 100644
--- a/arch/arm/boot/dts/imx51.dtsi
+++ b/arch/arm/boot/dts/imx51.dtsi
@@ -86,6 +86,11 @@
interrupt-parent = <&tzic>;
ranges;
+ iram: iram@1ffe0000 {
+ compatible = "mmio-sram";
+ reg = <0x1ffe0000 0x20000>;
+ };
+
ipu: ipu@40000000 {
#crtc-cells = <1>;
compatible = "fsl,imx51-ipu";
@@ -374,6 +379,14 @@
clocks = <&clks 107>;
};
+ owire: owire@83fa4000 {
+ compatible = "fsl,imx51-owire", "fsl,imx21-owire";
+ reg = <0x83fa4000 0x4000>;
+ interrupts = <88>;
+ clocks = <&clks 159>;
+ status = "disabled";
+ };
+
ecspi2: ecspi@83fac000 {
#address-cells = <1>;
#size-cells = <0>;
@@ -747,6 +760,11 @@
fsl,pins = <
MX51_PAD_UART1_RXD__UART1_RXD 0x1c5
MX51_PAD_UART1_TXD__UART1_TXD 0x1c5
+ >;
+ };
+
+ pinctrl_uart1_rtscts_1: uart1rtscts-1 {
+ fsl,pins = <
MX51_PAD_UART1_RTS__UART1_RTS 0x1c5
MX51_PAD_UART1_CTS__UART1_CTS 0x1c5
>;
@@ -767,6 +785,11 @@
fsl,pins = <
MX51_PAD_EIM_D25__UART3_RXD 0x1c5
MX51_PAD_EIM_D26__UART3_TXD 0x1c5
+ >;
+ };
+
+ pinctrl_uart3_rtscts_1: uart3rtscts-1 {
+ fsl,pins = <
MX51_PAD_EIM_D27__UART3_RTS 0x1c5
MX51_PAD_EIM_D24__UART3_CTS 0x1c5
>;
diff --git a/arch/arm/boot/dts/imx53-qsb.dts b/arch/arm/boot/dts/imx53-qsb.dts
index e97ddae..91a5935 100644
--- a/arch/arm/boot/dts/imx53-qsb.dts
+++ b/arch/arm/boot/dts/imx53-qsb.dts
@@ -55,19 +55,20 @@
label = "Power Button";
gpios = <&gpio1 8 0>;
linux,code = <116>; /* KEY_POWER */
- gpio-key,wakeup;
};
volume-up {
label = "Volume Up";
gpios = <&gpio2 14 0>;
linux,code = <115>; /* KEY_VOLUMEUP */
+ gpio-key,wakeup;
};
volume-down {
label = "Volume Down";
gpios = <&gpio2 15 0>;
linux,code = <114>; /* KEY_VOLUMEDOWN */
+ gpio-key,wakeup;
};
};
@@ -122,7 +123,6 @@
&esdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_esdhc1_1>;
- cd-gpios = <&gpio3 13 0>;
status = "okay";
};
@@ -136,6 +136,7 @@
pinctrl-0 = <&pinctrl_esdhc3_1>;
cd-gpios = <&gpio3 11 0>;
wp-gpios = <&gpio3 12 0>;
+ bus-width = <8>;
status = "okay";
};
@@ -152,7 +153,6 @@
MX53_PAD_PATA_DATA15__GPIO2_15 0x80000000
MX53_PAD_EIM_DA11__GPIO3_11 0x80000000
MX53_PAD_EIM_DA12__GPIO3_12 0x80000000
- MX53_PAD_EIM_DA13__GPIO3_13 0x80000000
MX53_PAD_PATA_DA_0__GPIO7_6 0x80000000
MX53_PAD_PATA_DA_2__GPIO7_8 0x80000000
MX53_PAD_GPIO_16__GPIO7_11 0x80000000
@@ -318,5 +318,6 @@
};
&usbotg {
- status = "okay";
+ dr_mode = "peripheral";
+ status = "okay";
};
diff --git a/arch/arm/boot/dts/imx6q-pinfunc.h b/arch/arm/boot/dts/imx6q-pinfunc.h
index 9bbe82b..97ed081 100644
--- a/arch/arm/boot/dts/imx6q-pinfunc.h
+++ b/arch/arm/boot/dts/imx6q-pinfunc.h
@@ -536,7 +536,7 @@
#define MX6QDL_PAD_ENET_REF_CLK__ESAI_RX_FS 0x1d4 0x4e8 0x85c 0x2 0x0
#define MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23 0x1d4 0x4e8 0x000 0x5 0x0
#define MX6QDL_PAD_ENET_REF_CLK__SPDIF_SR_CLK 0x1d4 0x4e8 0x000 0x6 0x0
-#define MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1d8 0x4ec 0x000 0x0 0x0
+#define MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1d8 0x4ec 0x004 0x0 0xff0d0100
#define MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1d8 0x4ec 0x000 0x1 0x0
#define MX6QDL_PAD_ENET_RX_ER__ESAI_RX_HF_CLK 0x1d8 0x4ec 0x864 0x2 0x0
#define MX6QDL_PAD_ENET_RX_ER__SPDIF_IN 0x1d8 0x4ec 0x914 0x3 0x1
@@ -654,7 +654,7 @@
#define MX6QDL_PAD_GPIO_1__ESAI_RX_CLK 0x224 0x5f4 0x86c 0x0 0x1
#define MX6QDL_PAD_GPIO_1__WDOG2_B 0x224 0x5f4 0x000 0x1 0x0
#define MX6QDL_PAD_GPIO_1__KEY_ROW5 0x224 0x5f4 0x8f4 0x2 0x0
-#define MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x224 0x5f4 0x000 0x3 0x0
+#define MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x224 0x5f4 0x004 0x3 0xff0d0101
#define MX6QDL_PAD_GPIO_1__PWM2_OUT 0x224 0x5f4 0x000 0x4 0x0
#define MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x224 0x5f4 0x000 0x5 0x0
#define MX6QDL_PAD_GPIO_1__SD1_CD_B 0x224 0x5f4 0x000 0x6 0x0
diff --git a/arch/arm/boot/dts/imx6q-sabrelite.dts b/arch/arm/boot/dts/imx6q-sabrelite.dts
index 3530280..f004913 100644
--- a/arch/arm/boot/dts/imx6q-sabrelite.dts
+++ b/arch/arm/boot/dts/imx6q-sabrelite.dts
@@ -65,8 +65,10 @@
};
};
-&sata {
+&audmux {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux_1>;
};
&ecspi1 {
@@ -83,11 +85,29 @@
};
};
-&ssi1 {
- fsl,mode = "i2s-slave";
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet_1>;
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio3 23 0>;
status = "okay";
};
+&i2c1 {
+ status = "okay";
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1_1>;
+
+ codec: sgtl5000@0a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ clocks = <&clks 201>;
+ VDDA-supply = <®_2p5v>;
+ VDDIO-supply = <®_3p3v>;
+ };
+};
+
&iomuxc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hog>;
@@ -103,11 +123,56 @@
MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x80000000
MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1f0b0
MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x80000000
+ MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x80000000
>;
};
};
};
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ };
+ };
+ };
+};
+
+&sata {
+ status = "okay";
+};
+
+&ssi1 {
+ fsl,mode = "i2s-slave";
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2_1>;
+};
+
+&usbh1 {
+ status = "okay";
+};
+
&usbotg {
vbus-supply = <®_usb_otg_vbus>;
pinctrl-names = "default";
@@ -116,18 +181,6 @@
status = "okay";
};
-&usbh1 {
- status = "okay";
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet_1>;
- phy-mode = "rgmii";
- phy-reset-gpios = <&gpio3 23 0>;
- status = "okay";
-};
-
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3_2>;
@@ -145,30 +198,3 @@
vmmc-supply = <®_3p3v>;
status = "okay";
};
-
-&audmux {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_audmux_1>;
-};
-
-&uart2 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2_1>;
-};
-
-&i2c1 {
- status = "okay";
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c1_1>;
-
- codec: sgtl5000@0a {
- compatible = "fsl,sgtl5000";
- reg = <0x0a>;
- clocks = <&clks 201>;
- VDDA-supply = <®_2p5v>;
- VDDIO-supply = <®_3p3v>;
- };
-};
diff --git a/arch/arm/boot/dts/imx6q-udoo.dts b/arch/arm/boot/dts/imx6q-udoo.dts
new file mode 100644
index 0000000..6e1ccdc
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-udoo.dts
@@ -0,0 +1,39 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+
+/ {
+ model = "Udoo i.MX6 Quad Board";
+ compatible = "udoo,imx6q-udoo", "fsl,imx6q";
+
+ memory {
+ reg = <0x10000000 0x40000000>;
+ };
+};
+
+&sata {
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2_1>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3_2>;
+ non-removable;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index 1cbbc51..ff6f1e8 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -54,6 +54,7 @@
fsl,pins = <
MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x80000000
MX6QDL_PAD_SD2_DAT2__GPIO1_IO13 0x80000000
+ MX6QDL_PAD_GPIO_18__SD3_VSELECT 0x17059
>;
};
};
@@ -74,8 +75,10 @@
};
&usdhc3 {
- pinctrl-names = "default";
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc3_1>;
+ pinctrl-1 = <&pinctrl_usdhc3_1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_1_200mhz>;
cd-gpios = <&gpio6 15 0>;
wp-gpios = <&gpio1 13 0>;
status = "okay";
diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
index 39eafc2..e75e11b 100644
--- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
@@ -80,6 +80,14 @@
mux-int-port = <2>;
mux-ext-port = <3>;
};
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <7>;
+ status = "okay";
+ };
};
&audmux {
@@ -108,6 +116,7 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet_1>;
phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio1 25 0>;
status = "okay";
};
@@ -172,6 +181,7 @@
MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x80000000
MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x80000000
MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x80000000
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x80000000
>;
};
};
@@ -202,6 +212,12 @@
};
};
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm0_1>;
+ status = "okay";
+};
+
&ssi2 {
fsl,mode = "i2s-slave";
status = "okay";
@@ -229,6 +245,7 @@
&usdhc2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc2_1>;
+ bus-width = <8>;
cd-gpios = <&gpio2 2 0>;
wp-gpios = <&gpio2 3 0>;
status = "okay";
@@ -237,6 +254,7 @@
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3_1>;
+ bus-width = <8>;
cd-gpios = <&gpio2 0 0>;
wp-gpios = <&gpio2 1 0>;
status = "okay";
diff --git a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
index a55113e..35f5479 100644
--- a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
@@ -43,6 +43,13 @@
mux-int-port = <1>;
mux-ext-port = <3>;
};
+
+ sound-spdif {
+ compatible = "fsl,imx-audio-spdif";
+ model = "imx-spdif";
+ spdif-controller = <&spdif>;
+ spdif-out;
+ };
};
&audmux {
@@ -81,6 +88,7 @@
MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x80000000 /* WL_REG_ON */
MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x80000000 /* WL_HOST_WAKE */
MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x80000000 /* WL_WAKE */
+ MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x80000000
>;
};
};
@@ -90,6 +98,13 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet_1>;
phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio3 29 0>;
+ status = "okay";
+};
+
+&spdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spdif_3>;
status = "okay";
};
@@ -115,6 +130,14 @@
status = "okay";
};
+&usbotg {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg_1>;
+ disable-over-current;
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
&usdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc1_2>;
diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi
index ccd55c2..59154dc 100644
--- a/arch/arm/boot/dts/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/imx6qdl.dtsi
@@ -116,6 +116,22 @@
arm,data-latency = <4 2 3>;
};
+ pcie: pcie@0x01000000 {
+ compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
+ reg = <0x01ffc000 0x4000>; /* DBI */
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000 /* configuration space */
+ 0x81000000 0 0 0x01f80000 0 0x00010000 /* downstream I/O */
+ 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */
+ num-lanes = <1>;
+ interrupts = <0 123 0x04>;
+ clocks = <&clks 189>, <&clks 187>, <&clks 206>, <&clks 144>;
+ clock-names = "pcie_ref_125m", "sata_ref_100m", "lvds_gate", "pcie_axi";
+ status = "disabled";
+ };
+
pmu {
compatible = "arm,cortex-a9-pmu";
interrupts = <0 94 0x04>;
@@ -136,8 +152,23 @@
ranges;
spdif: spdif@02004000 {
+ compatible = "fsl,imx35-spdif";
reg = <0x02004000 0x4000>;
interrupts = <0 52 0x04>;
+ dmas = <&sdma 14 18 0>,
+ <&sdma 15 18 0>;
+ dma-names = "rx", "tx";
+ clocks = <&clks 197>, <&clks 3>,
+ <&clks 197>, <&clks 107>,
+ <&clks 0>, <&clks 118>,
+ <&clks 62>, <&clks 139>,
+ <&clks 0>;
+ clock-names = "core", "rxtx0",
+ "rxtx1", "rxtx2",
+ "rxtx3", "rxtx4",
+ "rxtx5", "rxtx6",
+ "rxtx7";
+ status = "disabled";
};
ecspi1: ecspi@02008000 {
@@ -1010,6 +1041,12 @@
MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x1b0b0
>;
};
+
+ pinctrl_spdif_3: spdifgrp-3 {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD0__SPDIF_OUT 0x1b0b0
+ >;
+ };
};
uart1 {
@@ -1184,6 +1221,36 @@
>;
};
+ pinctrl_usdhc3_1_100mhz: usdhc3grp-1-100mhz { /* 100Mhz */
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170b9
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100b9
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170b9
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170b9
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170b9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170b9
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x170b9
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x170b9
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x170b9
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc3_1_200mhz: usdhc3grp-1-200mhz { /* 200Mhz */
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170f9
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100f9
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x170f9
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x170f9
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x170f9
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x170f9
+ >;
+ };
+
pinctrl_usdhc3_2: usdhc3grp-2 {
fsl,pins = <
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts
index 2886a59..cc68e19 100644
--- a/arch/arm/boot/dts/imx6sl-evk.dts
+++ b/arch/arm/boot/dts/imx6sl-evk.dts
@@ -17,6 +17,44 @@
memory {
reg = <0x80000000 0x40000000>;
};
+
+ regulators {
+ compatible = "simple-bus";
+
+ reg_usb_otg1_vbus: usb_otg1_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 0 0>;
+ enable-active-high;
+ };
+
+ reg_usb_otg2_vbus: usb_otg2_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg2_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 2 0>;
+ enable-active-high;
+ };
+ };
+};
+
+&ecspi1 {
+ fsl,spi-num-chipselects = <1>;
+ cs-gpios = <&gpio4 11 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1_1>;
+ status = "okay";
+
+ flash: m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p32";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
};
&fec {
@@ -38,6 +76,8 @@
MX6SL_PAD_SD2_DAT7__GPIO5_IO00 0x17059
MX6SL_PAD_SD2_DAT6__GPIO4_IO29 0x17059
MX6SL_PAD_REF_CLK_32K__GPIO3_IO22 0x17059
+ MX6SL_PAD_KEY_COL4__GPIO4_IO00 0x80000000
+ MX6SL_PAD_KEY_COL5__GPIO4_IO02 0x80000000
>;
};
};
@@ -49,9 +89,26 @@
status = "okay";
};
-&usdhc1 {
+&usbotg1 {
+ vbus-supply = <®_usb_otg1_vbus>;
pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg1_1>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg2 {
+ vbus-supply = <®_usb_otg2_vbus>;
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc1_1>;
+ pinctrl-1 = <&pinctrl_usdhc1_1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_1_200mhz>;
bus-width = <8>;
cd-gpios = <&gpio4 7 0>;
wp-gpios = <&gpio4 6 0>;
@@ -59,16 +116,20 @@
};
&usdhc2 {
- pinctrl-names = "default";
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc2_1>;
+ pinctrl-1 = <&pinctrl_usdhc2_1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_1_200mhz>;
cd-gpios = <&gpio5 0 0>;
wp-gpios = <&gpio4 29 0>;
status = "okay";
};
&usdhc3 {
- pinctrl-names = "default";
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc3_1>;
+ pinctrl-1 = <&pinctrl_usdhc3_1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_1_200mhz>;
cd-gpios = <&gpio3 22 0>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi
index c46651e..6eabfa1 100644
--- a/arch/arm/boot/dts/imx6sl.dtsi
+++ b/arch/arm/boot/dts/imx6sl.dtsi
@@ -13,16 +13,20 @@
/ {
aliases {
- serial0 = &uart1;
- serial1 = &uart2;
- serial2 = &uart3;
- serial3 = &uart4;
- serial4 = &uart5;
gpio0 = &gpio1;
gpio1 = &gpio2;
gpio2 = &gpio3;
gpio3 = &gpio4;
gpio4 = &gpio5;
+ serial0 = &uart1;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ serial3 = &uart4;
+ serial4 = &uart5;
+ spi0 = &ecspi1;
+ spi1 = &ecspi2;
+ spi2 = &ecspi3;
+ spi3 = &ecspi4;
};
cpus {
@@ -528,10 +532,26 @@
interrupts = <0 89 0x04>;
};
+ gpr: iomuxc-gpr@020e0000 {
+ compatible = "fsl,imx6sl-iomuxc-gpr",
+ "fsl,imx6q-iomuxc-gpr", "syscon";
+ reg = <0x020e0000 0x38>;
+ };
+
iomuxc: iomuxc@020e0000 {
compatible = "fsl,imx6sl-iomuxc";
reg = <0x020e0000 0x4000>;
+ ecspi1 {
+ pinctrl_ecspi1_1: ecspi1grp-1 {
+ fsl,pins = <
+ MX6SL_PAD_ECSPI1_MISO__ECSPI1_MISO 0x100b1
+ MX6SL_PAD_ECSPI1_MOSI__ECSPI1_MOSI 0x100b1
+ MX6SL_PAD_ECSPI1_SCLK__ECSPI1_SCLK 0x100b1
+ >;
+ };
+ };
+
fec {
pinctrl_fec_1: fecgrp-1 {
fsl,pins = <
@@ -557,6 +577,64 @@
};
};
+ usbotg1 {
+ pinctrl_usbotg1_1: usbotg1grp-1 {
+ fsl,pins = <
+ MX6SL_PAD_EPDC_PWRCOM__USB_OTG1_ID 0x17059
+ >;
+ };
+
+ pinctrl_usbotg1_2: usbotg1grp-2 {
+ fsl,pins = <
+ MX6SL_PAD_FEC_RXD0__USB_OTG1_ID 0x17059
+ >;
+ };
+
+ pinctrl_usbotg1_3: usbotg1grp-3 {
+ fsl,pins = <
+ MX6SL_PAD_LCD_DAT1__USB_OTG1_ID 0x17059
+ >;
+ };
+
+ pinctrl_usbotg1_4: usbotg1grp-4 {
+ fsl,pins = <
+ MX6SL_PAD_REF_CLK_32K__USB_OTG1_ID 0x17059
+ >;
+ };
+
+ pinctrl_usbotg1_5: usbotg1grp-5 {
+ fsl,pins = <
+ MX6SL_PAD_SD3_DAT0__USB_OTG1_ID 0x17059
+ >;
+ };
+ };
+
+ usbotg2 {
+ pinctrl_usbotg2_1: usbotg2grp-1 {
+ fsl,pins = <
+ MX6SL_PAD_ECSPI1_SCLK__USB_OTG2_OC 0x17059
+ >;
+ };
+
+ pinctrl_usbotg2_2: usbotg2grp-2 {
+ fsl,pins = <
+ MX6SL_PAD_ECSPI2_SCLK__USB_OTG2_OC 0x17059
+ >;
+ };
+
+ pinctrl_usbotg2_3: usbotg2grp-3 {
+ fsl,pins = <
+ MX6SL_PAD_KEY_ROW5__USB_OTG2_OC 0x17059
+ >;
+ };
+
+ pinctrl_usbotg2_4: usbotg2grp-4 {
+ fsl,pins = <
+ MX6SL_PAD_SD3_DAT2__USB_OTG2_OC 0x17059
+ >;
+ };
+ };
+
usdhc1 {
pinctrl_usdhc1_1: usdhc1grp-1 {
fsl,pins = <
@@ -572,6 +650,38 @@
MX6SL_PAD_SD1_DAT7__SD1_DATA7 0x17059
>;
};
+
+ pinctrl_usdhc1_1_100mhz: usdhc1grp-1-100mhz {
+ fsl,pins = <
+ MX6SL_PAD_SD1_CMD__SD1_CMD 0x170b9
+ MX6SL_PAD_SD1_CLK__SD1_CLK 0x100b9
+ MX6SL_PAD_SD1_DAT0__SD1_DATA0 0x170b9
+ MX6SL_PAD_SD1_DAT1__SD1_DATA1 0x170b9
+ MX6SL_PAD_SD1_DAT2__SD1_DATA2 0x170b9
+ MX6SL_PAD_SD1_DAT3__SD1_DATA3 0x170b9
+ MX6SL_PAD_SD1_DAT4__SD1_DATA4 0x170b9
+ MX6SL_PAD_SD1_DAT5__SD1_DATA5 0x170b9
+ MX6SL_PAD_SD1_DAT6__SD1_DATA6 0x170b9
+ MX6SL_PAD_SD1_DAT7__SD1_DATA7 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc1_1_200mhz: usdhc1grp-1-200mhz {
+ fsl,pins = <
+ MX6SL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6SL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6SL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6SL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6SL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6SL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6SL_PAD_SD1_DAT4__SD1_DATA4 0x170f9
+ MX6SL_PAD_SD1_DAT5__SD1_DATA5 0x170f9
+ MX6SL_PAD_SD1_DAT6__SD1_DATA6 0x170f9
+ MX6SL_PAD_SD1_DAT7__SD1_DATA7 0x170f9
+ >;
+ };
+
+
};
usdhc2 {
@@ -585,6 +695,29 @@
MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x17059
>;
};
+
+ pinctrl_usdhc2_1_100mhz: usdhc2grp-1-100mhz {
+ fsl,pins = <
+ MX6SL_PAD_SD2_CMD__SD2_CMD 0x170b9
+ MX6SL_PAD_SD2_CLK__SD2_CLK 0x100b9
+ MX6SL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
+ MX6SL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
+ MX6SL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
+ MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc2_1_200mhz: usdhc2grp-1-200mhz {
+ fsl,pins = <
+ MX6SL_PAD_SD2_CMD__SD2_CMD 0x170f9
+ MX6SL_PAD_SD2_CLK__SD2_CLK 0x100f9
+ MX6SL_PAD_SD2_DAT0__SD2_DATA0 0x170f9
+ MX6SL_PAD_SD2_DAT1__SD2_DATA1 0x170f9
+ MX6SL_PAD_SD2_DAT2__SD2_DATA2 0x170f9
+ MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x170f9
+ >;
+ };
+
};
usdhc3 {
@@ -598,6 +731,28 @@
MX6SL_PAD_SD3_DAT3__SD3_DATA3 0x17059
>;
};
+
+ pinctrl_usdhc3_1_100mhz: usdhc3grp-1-100mhz {
+ fsl,pins = <
+ MX6SL_PAD_SD3_CMD__SD3_CMD 0x170b9
+ MX6SL_PAD_SD3_CLK__SD3_CLK 0x100b9
+ MX6SL_PAD_SD3_DAT0__SD3_DATA0 0x170b9
+ MX6SL_PAD_SD3_DAT1__SD3_DATA1 0x170b9
+ MX6SL_PAD_SD3_DAT2__SD3_DATA2 0x170b9
+ MX6SL_PAD_SD3_DAT3__SD3_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc3_1_200mhz: usdhc3grp-1-200mhz {
+ fsl,pins = <
+ MX6SL_PAD_SD3_CMD__SD3_CMD 0x170f9
+ MX6SL_PAD_SD3_CLK__SD3_CLK 0x100f9
+ MX6SL_PAD_SD3_DAT0__SD3_DATA0 0x170f9
+ MX6SL_PAD_SD3_DAT1__SD3_DATA1 0x170f9
+ MX6SL_PAD_SD3_DAT2__SD3_DATA2 0x170f9
+ MX6SL_PAD_SD3_DAT3__SD3_DATA3 0x170f9
+ >;
+ };
};
};
@@ -619,7 +774,8 @@
<&clks IMX6SL_CLK_SDMA>;
clock-names = "ipg", "ahb";
#dma-cells = <3>;
- fsl,sdma-ram-script-name = "imx/sdma/sdma-imx6sl.bin";
+ /* imx6sl reuses imx6q sdma firmware */
+ fsl,sdma-ram-script-name = "imx/sdma/sdma-imx6q.bin";
};
pxp: pxp@020f0000 {
@@ -663,7 +819,7 @@
usbotg2: usb@02184200 {
compatible = "fsl,imx6sl-usb", "fsl,imx27-usb";
reg = <0x02184200 0x200>;
- interrupts = <0 40 0x04>;
+ interrupts = <0 42 0x04>;
clocks = <&clks IMX6SL_CLK_USBOH3>;
fsl,usbphy = <&usbphy2>;
fsl,usbmisc = <&usbmisc 1>;
@@ -673,7 +829,7 @@
usbh: usb@02184400 {
compatible = "fsl,imx6sl-usb", "fsl,imx27-usb";
reg = <0x02184400 0x200>;
- interrupts = <0 42 0x04>;
+ interrupts = <0 40 0x04>;
clocks = <&clks IMX6SL_CLK_USBOH3>;
fsl,usbmisc = <&usbmisc 2>;
status = "disabled";
diff --git a/arch/arm/boot/dts/kirkwood-db-88f6281.dts b/arch/arm/boot/dts/kirkwood-db-88f6281.dts
index 72c4b0a..c39dd76 100644
--- a/arch/arm/boot/dts/kirkwood-db-88f6281.dts
+++ b/arch/arm/boot/dts/kirkwood-db-88f6281.dts
@@ -19,7 +19,6 @@
compatible = "marvell,db-88f6281-bp", "marvell,kirkwood-88f6281", "marvell,kirkwood";
mbus {
- ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>;
pcie-controller {
status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood-db-88f6282.dts b/arch/arm/boot/dts/kirkwood-db-88f6282.dts
index 36c411d..701c6b6 100644
--- a/arch/arm/boot/dts/kirkwood-db-88f6282.dts
+++ b/arch/arm/boot/dts/kirkwood-db-88f6282.dts
@@ -19,7 +19,6 @@
compatible = "marvell,db-88f6282-bp", "marvell,kirkwood-88f6282", "marvell,kirkwood";
mbus {
- ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>;
pcie-controller {
status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood-db.dtsi b/arch/arm/boot/dts/kirkwood-db.dtsi
index c0e2a58..053aa20 100644
--- a/arch/arm/boot/dts/kirkwood-db.dtsi
+++ b/arch/arm/boot/dts/kirkwood-db.dtsi
@@ -39,28 +39,6 @@
status = "ok";
};
- nand@3000000 {
- pinctrl-0 = <&pmx_nand>;
- pinctrl-names = "default";
- chip-delay = <25>;
- status = "okay";
-
- partition@0 {
- label = "uboot";
- reg = <0x0 0x100000>;
- };
-
- partition@100000 {
- label = "uImage";
- reg = <0x100000 0x400000>;
- };
-
- partition@500000 {
- label = "root";
- reg = <0x500000 0x1fb00000>;
- };
- };
-
sata@80000 {
nr-ports = <2>;
status = "okay";
@@ -80,6 +58,28 @@
};
};
+&nand {
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+ chip-delay = <25>;
+ status = "okay";
+
+ partition@0 {
+ label = "uboot";
+ reg = <0x0 0x100000>;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x100000 0x400000>;
+ };
+
+ partition@500000 {
+ label = "root";
+ reg = <0x500000 0x1fb00000>;
+ };
+};
+
&mdio {
status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood-dnskw.dtsi b/arch/arm/boot/dts/kirkwood-dnskw.dtsi
index d544f77..aefa375 100644
--- a/arch/arm/boot/dts/kirkwood-dnskw.dtsi
+++ b/arch/arm/boot/dts/kirkwood-dnskw.dtsi
@@ -148,44 +148,6 @@
status = "okay";
nr-ports = <2>;
};
-
- nand@3000000 {
- pinctrl-0 = <&pmx_nand>;
- pinctrl-names = "default";
- status = "okay";
- chip-delay = <35>;
-
- partition@0 {
- label = "u-boot";
- reg = <0x0000000 0x100000>;
- read-only;
- };
-
- partition@100000 {
- label = "uImage";
- reg = <0x0100000 0x500000>;
- };
-
- partition@600000 {
- label = "ramdisk";
- reg = <0x0600000 0x500000>;
- };
-
- partition@b00000 {
- label = "image";
- reg = <0x0b00000 0x6600000>;
- };
-
- partition@7100000 {
- label = "mini firmware";
- reg = <0x7100000 0xa00000>;
- };
-
- partition@7b00000 {
- label = "config";
- reg = <0x7b00000 0x500000>;
- };
- };
};
regulators {
@@ -220,6 +182,44 @@
};
};
+&nand {
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+ status = "okay";
+ chip-delay = <35>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x500000>;
+ };
+
+ partition@600000 {
+ label = "ramdisk";
+ reg = <0x0600000 0x500000>;
+ };
+
+ partition@b00000 {
+ label = "image";
+ reg = <0x0b00000 0x6600000>;
+ };
+
+ partition@7100000 {
+ label = "mini firmware";
+ reg = <0x7100000 0xa00000>;
+ };
+
+ partition@7b00000 {
+ label = "config";
+ reg = <0x7b00000 0x500000>;
+ };
+};
+
&mdio {
status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood-dockstar.dts b/arch/arm/boot/dts/kirkwood-dockstar.dts
index 59a2117..33ff368 100644
--- a/arch/arm/boot/dts/kirkwood-dockstar.dts
+++ b/arch/arm/boot/dts/kirkwood-dockstar.dts
@@ -34,26 +34,6 @@
serial@12000 {
status = "ok";
};
-
- nand@3000000 {
- status = "okay";
-
- partition@0 {
- label = "u-boot";
- reg = <0x0000000 0x100000>;
- read-only;
- };
-
- partition@100000 {
- label = "uImage";
- reg = <0x0100000 0x400000>;
- };
-
- partition@500000 {
- label = "data";
- reg = <0x0500000 0xfb00000>;
- };
- };
};
gpio-leds {
compatible = "gpio-leds";
@@ -91,6 +71,26 @@
};
};
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x400000>;
+ };
+
+ partition@500000 {
+ label = "data";
+ reg = <0x0500000 0xfb00000>;
+ };
+};
+
&mdio {
status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood-goflexnet.dts b/arch/arm/boot/dts/kirkwood-goflexnet.dts
index 6f7c7d7..a43bebb 100644
--- a/arch/arm/boot/dts/kirkwood-goflexnet.dts
+++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts
@@ -67,31 +67,6 @@
status = "ok";
};
- nand@3000000 {
- chip-delay = <40>;
- status = "okay";
-
- partition@0 {
- label = "u-boot";
- reg = <0x0000000 0x100000>;
- read-only;
- };
-
- partition@100000 {
- label = "uImage";
- reg = <0x0100000 0x400000>;
- };
-
- partition@500000 {
- label = "pogoplug";
- reg = <0x0500000 0x2000000>;
- };
-
- partition@2500000 {
- label = "root";
- reg = <0x02500000 0xd800000>;
- };
- };
sata@80000 {
status = "okay";
nr-ports = <2>;
@@ -171,6 +146,32 @@
};
};
+&nand {
+ chip-delay = <40>;
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x400000>;
+ };
+
+ partition@500000 {
+ label = "pogoplug";
+ reg = <0x0500000 0x2000000>;
+ };
+
+ partition@2500000 {
+ label = "root";
+ reg = <0x02500000 0xd800000>;
+ };
+};
+
&mdio {
status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts b/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts
index 6548b9d..d30a91a 100644
--- a/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts
+++ b/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts
@@ -40,26 +40,6 @@
status = "ok";
};
- nand@3000000 {
- status = "okay";
-
- partition@0 {
- label = "u-boot";
- reg = <0x00000000 0x00100000>;
- read-only;
- };
-
- partition@100000 {
- label = "uImage";
- reg = <0x00100000 0x00400000>;
- };
-
- partition@500000 {
- label = "data";
- reg = <0x00500000 0x1fb00000>;
- };
- };
-
sata@80000 {
status = "okay";
nr-ports = <1>;
@@ -97,6 +77,26 @@
};
};
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x00000000 0x00100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x00100000 0x00400000>;
+ };
+
+ partition@500000 {
+ label = "data";
+ reg = <0x00500000 0x1fb00000>;
+ };
+};
+
&mdio {
status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood-ib62x0.dts b/arch/arm/boot/dts/kirkwood-ib62x0.dts
index cb711a3..c5fb02f 100644
--- a/arch/arm/boot/dts/kirkwood-ib62x0.dts
+++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts
@@ -5,7 +5,7 @@
/ {
model = "RaidSonic ICY BOX IB-NAS62x0 (Rev B)";
- compatible = "raidsonic,ib-nas6210-b", "raidsonic,ib-nas6220-b", "raidsonic,ib-nas6210", "raidsonic,ib-nas6220", "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+ compatible = "raidsonic,ib-nas6210-b", "raidsonic,ib-nas6220-b", "raidsonic,ib-nas6210", "raidsonic,ib-nas6220", "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood";
memory {
device_type = "memory";
@@ -43,6 +43,7 @@
marvell,function = "gpio";
};
};
+
serial@12000 {
status = "okay";
};
@@ -51,28 +52,6 @@
status = "okay";
nr-ports = <2>;
};
-
- nand@3000000 {
- status = "okay";
- pinctrl-0 = <&pmx_nand>;
- pinctrl-names = "default";
-
- partition@0 {
- label = "u-boot";
- reg = <0x0000000 0x100000>;
- };
-
- partition@100000 {
- label = "uImage";
- reg = <0x0100000 0x600000>;
- };
-
- partition@700000 {
- label = "root";
- reg = <0x0700000 0xf900000>;
- };
-
- };
};
gpio_keys {
@@ -93,6 +72,7 @@
gpios = <&gpio0 28 1>;
};
};
+
gpio-leds {
compatible = "gpio-leds";
pinctrl-0 = <&pmx_led_os_red &pmx_led_os_green
@@ -113,13 +93,39 @@
gpios = <&gpio0 27 0>;
};
};
+
gpio_poweroff {
compatible = "gpio-poweroff";
pinctrl-0 = <&pmx_power_off>;
pinctrl-names = "default";
gpios = <&gpio0 24 0>;
};
+};
+&nand {
+ status = "okay";
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0xe0000>;
+ };
+
+ partition@e0000 {
+ label = "u-boot environment";
+ reg = <0xe0000 0x100000>;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x600000>;
+ };
+
+ partition@700000 {
+ label = "root";
+ reg = <0x0700000 0xf900000>;
+ };
};
@@ -134,6 +140,7 @@
ð0 {
status = "okay";
+
ethernet0-port@0 {
phy-handle = <ðphy0>;
};
diff --git a/arch/arm/boot/dts/kirkwood-iconnect.dts b/arch/arm/boot/dts/kirkwood-iconnect.dts
index 0323f01..4a62b20 100644
--- a/arch/arm/boot/dts/kirkwood-iconnect.dts
+++ b/arch/arm/boot/dts/kirkwood-iconnect.dts
@@ -19,7 +19,6 @@
};
mbus {
- ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>;
pcie-controller {
status = "okay";
@@ -83,35 +82,6 @@
serial@12000 {
status = "ok";
};
-
- nand@3000000 {
- status = "okay";
-
- partition@0 {
- label = "uboot";
- reg = <0x0000000 0xc0000>;
- };
-
- partition@a0000 {
- label = "env";
- reg = <0xa0000 0x20000>;
- };
-
- partition@100000 {
- label = "zImage";
- reg = <0x100000 0x300000>;
- };
-
- partition@540000 {
- label = "initrd";
- reg = <0x540000 0x300000>;
- };
-
- partition@980000 {
- label = "boot";
- reg = <0x980000 0x1f400000>;
- };
- };
};
gpio-leds {
@@ -180,6 +150,35 @@
};
};
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "uboot";
+ reg = <0x0000000 0xc0000>;
+ };
+
+ partition@a0000 {
+ label = "env";
+ reg = <0xa0000 0x20000>;
+ };
+
+ partition@100000 {
+ label = "zImage";
+ reg = <0x100000 0x300000>;
+ };
+
+ partition@540000 {
+ label = "initrd";
+ reg = <0x540000 0x300000>;
+ };
+
+ partition@980000 {
+ label = "boot";
+ reg = <0x980000 0x1f400000>;
+ };
+};
+
&mdio {
status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
index df84474..d15395d 100644
--- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
+++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
@@ -113,31 +113,6 @@
status = "ok";
};
- nand@3000000 {
- status = "okay";
-
- partition@0 {
- label = "u-boot";
- reg = <0x0000000 0x100000>;
- read-only;
- };
-
- partition@a0000 {
- label = "env";
- reg = <0xa0000 0x20000>;
- read-only;
- };
-
- partition@100000 {
- label = "uImage";
- reg = <0x100000 0x300000>;
- };
-
- partition@400000 {
- label = "uInitrd";
- reg = <0x540000 0x1000000>;
- };
- };
sata@80000 {
status = "okay";
nr-ports = <2>;
@@ -195,6 +170,32 @@
};
};
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ partition@a0000 {
+ label = "env";
+ reg = <0xa0000 0x20000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x100000 0x300000>;
+ };
+
+ partition@400000 {
+ label = "uInitrd";
+ reg = <0x540000 0x1000000>;
+ };
+};
+
&mdio {
status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts b/arch/arm/boot/dts/kirkwood-km_kirkwood.dts
index 6899408..cd44f37 100644
--- a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts
+++ b/arch/arm/boot/dts/kirkwood-km_kirkwood.dts
@@ -34,13 +34,6 @@
serial@12000 {
status = "ok";
};
-
- nand@3000000 {
- pinctrl-0 = <&pmx_nand>;
- pinctrl-names = "default";
- status = "ok";
- chip-delay = <25>;
- };
};
i2c@0 {
@@ -51,6 +44,13 @@
};
};
+&nand {
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+ status = "ok";
+ chip-delay = <25>;
+};
+
&mdio {
status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood-mplcec4.dts b/arch/arm/boot/dts/kirkwood-mplcec4.dts
index ce2b94b..6c1ec27 100644
--- a/arch/arm/boot/dts/kirkwood-mplcec4.dts
+++ b/arch/arm/boot/dts/kirkwood-mplcec4.dts
@@ -17,7 +17,6 @@
};
mbus {
- ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>;
pcie-controller {
status = "okay";
@@ -96,37 +95,6 @@
pinctrl-names = "default";
};
- nand@3000000 {
- pinctrl-0 = <&pmx_nand>;
- pinctrl-names = "default";
- status = "okay";
-
- partition@0 {
- label = "uboot";
- reg = <0x0000000 0x100000>;
- };
-
- partition@100000 {
- label = "env";
- reg = <0x100000 0x80000>;
- };
-
- partition@180000 {
- label = "fdt";
- reg = <0x180000 0x80000>;
- };
-
- partition@200000 {
- label = "kernel";
- reg = <0x200000 0x400000>;
- };
-
- partition@600000 {
- label = "rootfs";
- reg = <0x600000 0x1fa00000>;
- };
- };
-
rtc@10300 {
status = "disabled";
};
@@ -194,6 +162,37 @@
};
};
+&nand {
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ partition@0 {
+ label = "uboot";
+ reg = <0x0000000 0x100000>;
+ };
+
+ partition@100000 {
+ label = "env";
+ reg = <0x100000 0x80000>;
+ };
+
+ partition@180000 {
+ label = "fdt";
+ reg = <0x180000 0x80000>;
+ };
+
+ partition@200000 {
+ label = "kernel";
+ reg = <0x200000 0x400000>;
+ };
+
+ partition@600000 {
+ label = "rootfs";
+ reg = <0x600000 0x1fa00000>;
+ };
+};
+
&mdio {
status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts b/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
index 874857e..e6a102c 100644
--- a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
+++ b/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
@@ -17,7 +17,6 @@
};
mbus {
- ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>;
pcie-controller {
status = "okay";
@@ -98,36 +97,6 @@
status = "okay";
};
- nand@3000000 {
- status = "okay";
-
- partition@0 {
- label = "u-boot";
- reg = <0x0000000 0x180000>;
- read-only;
- };
-
- partition@180000 {
- label = "u-boot-env";
- reg = <0x180000 0x20000>;
- };
-
- partition@200000 {
- label = "uImage";
- reg = <0x0200000 0x600000>;
- };
-
- partition@800000 {
- label = "minirootfs";
- reg = <0x0800000 0x1000000>;
- };
-
- partition@1800000 {
- label = "jffs2";
- reg = <0x1800000 0x6800000>;
- };
- };
-
sata@80000 {
status = "okay";
nr-ports = <2>;
@@ -208,6 +177,36 @@
};
};
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x180000>;
+ read-only;
+ };
+
+ partition@180000 {
+ label = "u-boot-env";
+ reg = <0x180000 0x20000>;
+ };
+
+ partition@200000 {
+ label = "uImage";
+ reg = <0x0200000 0x600000>;
+ };
+
+ partition@800000 {
+ label = "minirootfs";
+ reg = <0x0800000 0x1000000>;
+ };
+
+ partition@1800000 {
+ label = "jffs2";
+ reg = <0x1800000 0x6800000>;
+ };
+};
+
&mdio {
status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi b/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi
index 06267a9..e3f915d 100644
--- a/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi
+++ b/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi
@@ -27,49 +27,6 @@
nr-ports = <2>;
};
- nand@3000000 {
- status = "okay";
- chip-delay = <35>;
-
- partition@0 {
- label = "uboot";
- reg = <0x0000000 0x0100000>;
- read-only;
- };
- partition@100000 {
- label = "uboot_env";
- reg = <0x0100000 0x0080000>;
- };
- partition@180000 {
- label = "key_store";
- reg = <0x0180000 0x0080000>;
- };
- partition@200000 {
- label = "info";
- reg = <0x0200000 0x0080000>;
- };
- partition@280000 {
- label = "etc";
- reg = <0x0280000 0x0a00000>;
- };
- partition@c80000 {
- label = "kernel_1";
- reg = <0x0c80000 0x0a00000>;
- };
- partition@1680000 {
- label = "rootfs1";
- reg = <0x1680000 0x2fc0000>;
- };
- partition@4640000 {
- label = "kernel_2";
- reg = <0x4640000 0x0a00000>;
- };
- partition@5040000 {
- label = "rootfs2";
- reg = <0x5040000 0x2fc0000>;
- };
- };
-
pcie-controller {
status = "okay";
@@ -105,3 +62,46 @@
};
};
};
+
+&nand {
+ status = "okay";
+ chip-delay = <35>;
+
+ partition@0 {
+ label = "uboot";
+ reg = <0x0000000 0x0100000>;
+ read-only;
+ };
+ partition@100000 {
+ label = "uboot_env";
+ reg = <0x0100000 0x0080000>;
+ };
+ partition@180000 {
+ label = "key_store";
+ reg = <0x0180000 0x0080000>;
+ };
+ partition@200000 {
+ label = "info";
+ reg = <0x0200000 0x0080000>;
+ };
+ partition@280000 {
+ label = "etc";
+ reg = <0x0280000 0x0a00000>;
+ };
+ partition@c80000 {
+ label = "kernel_1";
+ reg = <0x0c80000 0x0a00000>;
+ };
+ partition@1680000 {
+ label = "rootfs1";
+ reg = <0x1680000 0x2fc0000>;
+ };
+ partition@4640000 {
+ label = "kernel_2";
+ reg = <0x4640000 0x0a00000>;
+ };
+ partition@5040000 {
+ label = "rootfs2";
+ reg = <0x5040000 0x2fc0000>;
+ };
+};
diff --git a/arch/arm/boot/dts/kirkwood-nsa310.dts b/arch/arm/boot/dts/kirkwood-nsa310.dts
index 7aeae0c..b5418bc 100644
--- a/arch/arm/boot/dts/kirkwood-nsa310.dts
+++ b/arch/arm/boot/dts/kirkwood-nsa310.dts
@@ -15,7 +15,6 @@
};
mbus {
- ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>;
pcie-controller {
status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts b/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
index 85ccf8d..f0e3d21 100644
--- a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
+++ b/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
@@ -29,43 +29,6 @@
pinctrl-names = "default";
};
- nand@3000000 {
- chip-delay = <25>;
- status = "okay";
- pinctrl-0 = <&pmx_nand>;
- pinctrl-names = "default";
-
- partition@0 {
- label = "uboot";
- reg = <0x0 0x90000>;
- };
-
- partition@90000 {
- label = "env";
- reg = <0x90000 0x44000>;
- };
-
- partition@d4000 {
- label = "test";
- reg = <0xd4000 0x24000>;
- };
-
- partition@f4000 {
- label = "conf";
- reg = <0xf4000 0x400000>;
- };
-
- partition@4f4000 {
- label = "linux";
- reg = <0x4f4000 0x1d20000>;
- };
-
- partition@2214000 {
- label = "user";
- reg = <0x2214000 0x1dec000>;
- };
- };
-
sata@80000 {
nr-ports = <1>;
status = "okay";
@@ -167,6 +130,43 @@
};
};
+&nand {
+ chip-delay = <25>;
+ status = "okay";
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+
+ partition@0 {
+ label = "uboot";
+ reg = <0x0 0x90000>;
+ };
+
+ partition@90000 {
+ label = "env";
+ reg = <0x90000 0x44000>;
+ };
+
+ partition@d4000 {
+ label = "test";
+ reg = <0xd4000 0x24000>;
+ };
+
+ partition@f4000 {
+ label = "conf";
+ reg = <0xf4000 0x400000>;
+ };
+
+ partition@4f4000 {
+ label = "linux";
+ reg = <0x4f4000 0x1d20000>;
+ };
+
+ partition@2214000 {
+ label = "user";
+ reg = <0x2214000 0x1dec000>;
+ };
+};
+
&mdio {
status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi b/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
index 5696b63..1173d7f 100644
--- a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
+++ b/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
@@ -48,27 +48,6 @@
pinctrl-names = "default";
status = "okay";
};
-
- nand@3000000 {
- pinctrl-0 = <&pmx_nand>;
- pinctrl-names = "default";
- status = "okay";
-
- partition@0 {
- label = "u-boot";
- reg = <0x0000000 0x100000>;
- };
-
- partition@100000 {
- label = "uImage";
- reg = <0x0100000 0x400000>;
- };
-
- partition@500000 {
- label = "root";
- reg = <0x0500000 0x1fb00000>;
- };
- };
};
regulators {
@@ -92,6 +71,27 @@
};
};
+&nand {
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x400000>;
+ };
+
+ partition@500000 {
+ label = "root";
+ reg = <0x0500000 0x1fb00000>;
+ };
+};
+
&mdio {
status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood-topkick.dts b/arch/arm/boot/dts/kirkwood-topkick.dts
index 30842b4..320da67 100644
--- a/arch/arm/boot/dts/kirkwood-topkick.dts
+++ b/arch/arm/boot/dts/kirkwood-topkick.dts
@@ -90,37 +90,6 @@
pinctrl-names = "default";
};
- nand@3000000 {
- status = "okay";
- pinctrl-0 = <&pmx_nand>;
- pinctrl-names = "default";
-
- partition@0 {
- label = "u-boot";
- reg = <0x0000000 0x180000>;
- };
-
- partition@180000 {
- label = "u-boot env";
- reg = <0x0180000 0x20000>;
- };
-
- partition@200000 {
- label = "uImage";
- reg = <0x0200000 0x600000>;
- };
-
- partition@800000 {
- label = "uInitrd";
- reg = <0x0800000 0x1000000>;
- };
-
- partition@1800000 {
- label = "rootfs";
- reg = <0x1800000 0xe800000>;
- };
- };
-
sata@80000 {
status = "okay";
nr-ports = <1>;
@@ -204,6 +173,37 @@
};
};
+&nand {
+ status = "okay";
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x180000>;
+ };
+
+ partition@180000 {
+ label = "u-boot env";
+ reg = <0x0180000 0x20000>;
+ };
+
+ partition@200000 {
+ label = "uImage";
+ reg = <0x0200000 0x600000>;
+ };
+
+ partition@800000 {
+ label = "uInitrd";
+ reg = <0x0800000 0x1000000>;
+ };
+
+ partition@1800000 {
+ label = "rootfs";
+ reg = <0x1800000 0xe800000>;
+ };
+};
+
&mdio {
status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood-ts219-6282.dts b/arch/arm/boot/dts/kirkwood-ts219-6282.dts
index 9efcd2d..345562f 100644
--- a/arch/arm/boot/dts/kirkwood-ts219-6282.dts
+++ b/arch/arm/boot/dts/kirkwood-ts219-6282.dts
@@ -6,7 +6,6 @@
/ {
mbus {
- ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>;
pcie-controller {
status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi
index 1335b2e..8b73c80 100644
--- a/arch/arm/boot/dts/kirkwood.dtsi
+++ b/arch/arm/boot/dts/kirkwood.dtsi
@@ -28,16 +28,43 @@
compatible = "marvell,kirkwood-mbus", "simple-bus";
#address-cells = <2>;
#size-cells = <1>;
+ /* If a board file needs to change this ranges it must replace it completely */
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 /* internal-regs */
+ MBUS_ID(0x01, 0x2f) 0 0xf4000000 0x10000 /* nand flash */
+ MBUS_ID(0x03, 0x01) 0 0xf5000000 0x10000 /* crypto sram */
+ >;
controller = <&mbusc>;
pcie-mem-aperture = <0xe0000000 0x10000000>; /* 256 MiB memory space */
pcie-io-aperture = <0xf2000000 0x100000>; /* 1 MiB I/O space */
+
+ crypto@0301 {
+ compatible = "marvell,orion-crypto";
+ reg = <MBUS_ID(0xf0, 0x01) 0x30000 0x10000>,
+ <MBUS_ID(0x03, 0x01) 0 0x800>;
+ reg-names = "regs", "sram";
+ interrupts = <22>;
+ clocks = <&gate_clk 17>;
+ status = "okay";
+ };
+
+ nand: nand@012f {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ cle = <0>;
+ ale = <1>;
+ bank-width = <1>;
+ compatible = "marvell,orion-nand";
+ reg = <MBUS_ID(0x01, 0x2f) 0 0x400>;
+ chip-delay = <25>;
+ /* set partition map and/or chip-delay in board dts */
+ clocks = <&gate_clk 7>;
+ status = "disabled";
+ };
};
ocp@f1000000 {
compatible = "simple-bus";
- ranges = <0x00000000 0xf1000000 0x0100000
- 0xf4000000 0xf4000000 0x0000400
- 0xf5000000 0xf5000000 0x0000400>;
+ ranges = <0x00000000 0xf1000000 0x0100000>;
#address-cells = <1>;
#size-cells = <1>;
@@ -193,20 +220,6 @@
status = "okay";
};
- nand@3000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cle = <0>;
- ale = <1>;
- bank-width = <1>;
- compatible = "marvell,orion-nand";
- reg = <0xf4000000 0x400>;
- chip-delay = <25>;
- /* set partition map and/or chip-delay in board dts */
- clocks = <&gate_clk 7>;
- status = "disabled";
- };
-
i2c@11000 {
compatible = "marvell,mv64xxx-i2c";
reg = <0x11000 0x20>;
@@ -218,16 +231,6 @@
status = "disabled";
};
- crypto@30000 {
- compatible = "marvell,orion-crypto";
- reg = <0x30000 0x10000>,
- <0xf5000000 0x800>;
- reg-names = "regs", "sram";
- interrupts = <22>;
- clocks = <&gate_clk 17>;
- status = "okay";
- };
-
mdio: mdio-bus@72004 {
compatible = "marvell,orion-mdio";
#address-cells = <1>;
diff --git a/arch/arm/boot/dts/mxs-pinfunc.h b/arch/arm/boot/dts/mxs-pinfunc.h
new file mode 100644
index 0000000..c6da987
--- /dev/null
+++ b/arch/arm/boot/dts/mxs-pinfunc.h
@@ -0,0 +1,31 @@
+/*
+ * Header providing constants for i.MX28 pinctrl bindings.
+ *
+ * Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#ifndef __DT_BINDINGS_MXS_PINCTRL_H__
+#define __DT_BINDINGS_MXS_PINCTRL_H__
+
+/* fsl,drive-strength property */
+#define MXS_DRIVE_4mA 0
+#define MXS_DRIVE_8mA 1
+#define MXS_DRIVE_12mA 2
+#define MXS_DRIVE_16mA 3
+
+/* fsl,voltage property */
+#define MXS_VOLTAGE_LOW 0
+#define MXS_VOLTAGE_HIGH 1
+
+/* fsl,pull-up property */
+#define MXS_PULL_DISABLE 0
+#define MXS_PULL_ENABLE 1
+
+#endif /* __DT_BINDINGS_MXS_PINCTRL_H__ */
diff --git a/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi b/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
new file mode 100644
index 0000000..9c18adf
--- /dev/null
+++ b/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
@@ -0,0 +1,52 @@
+/*
+ * Common file for GPMC connected smsc911x on omaps
+ *
+ * Note that the board specifc DTS file needs to specify
+ * ranges, pinctrl, reg, interrupt parent and interrupts.
+ */
+
+/ {
+ vddvario: regulator-vddvario {
+ compatible = "regulator-fixed";
+ regulator-name = "vddvario";
+ regulator-always-on;
+ };
+
+ vdd33a: regulator-vdd33a {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd33a";
+ regulator-always-on;
+ };
+};
+
+&gpmc {
+ ethernet@gpmc {
+ compatible = "smsc,lan9221", "smsc,lan9115";
+ bank-width = <2>;
+ gpmc,mux-add-data;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <186>;
+ gpmc,cs-wr-off-ns = <186>;
+ gpmc,adv-on-ns = <12>;
+ gpmc,adv-rd-off-ns = <48>;
+ gpmc,adv-wr-off-ns = <48>;
+ gpmc,oe-on-ns = <54>;
+ gpmc,oe-off-ns = <168>;
+ gpmc,we-on-ns = <54>;
+ gpmc,we-off-ns = <168>;
+ gpmc,rd-cycle-ns = <186>;
+ gpmc,wr-cycle-ns = <186>;
+ gpmc,access-ns = <114>;
+ gpmc,page-burst-access-ns = <6>;
+ gpmc,bus-turnaround-ns = <12>;
+ gpmc,cycle2cycle-delay-ns = <18>;
+ gpmc,wr-data-mux-bus-ns = <90>;
+ gpmc,wr-access-ns = <186>;
+ gpmc,cycle2cycle-samecsen;
+ gpmc,cycle2cycle-diffcsen;
+ vmmc-supply = <&vddvario>;
+ vmmc_aux-supply = <&vdd33a>;
+ reg-io-width = <4>;
+ smsc,save-mac-address;
+ };
+};
diff --git a/arch/arm/boot/dts/omap-zoom-common.dtsi b/arch/arm/boot/dts/omap-zoom-common.dtsi
new file mode 100644
index 0000000..b0ee342
--- /dev/null
+++ b/arch/arm/boot/dts/omap-zoom-common.dtsi
@@ -0,0 +1,33 @@
+/*
+ * Common features on the Zoom debug board
+ */
+
+#include "omap-gpmc-smsc911x.dtsi"
+
+&gpmc {
+ ranges = <3 0 0x10000000 0x00000400>,
+ <7 0 0x2c000000 0x01000000>;
+
+ /*
+ * Four port TL16CP754C serial port on GPMC,
+ * they probably share the same GPIO IRQ
+ * REVISIT: Add timing support from slls644g.pdf
+ */
+ 8250@3,0 {
+ compatible = "ns16550a";
+ reg = <3 0 0x100>;
+ bank-width = <2>;
+ reg-shift = <1>;
+ reg-io-width = <1>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <6 IRQ_TYPE_EDGE_RISING>; /* gpio102 */
+ clock-frequency = <1843200>;
+ current-speed = <115200>;
+ };
+
+ ethernet@gpmc {
+ reg = <7 0 0xff>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <30 IRQ_TYPE_LEVEL_LOW>; /* gpio158 */
+ };
+};
diff --git a/arch/arm/boot/dts/omap2420-h4.dts b/arch/arm/boot/dts/omap2420-h4.dts
index 224c08f..34cdecb 100644
--- a/arch/arm/boot/dts/omap2420-h4.dts
+++ b/arch/arm/boot/dts/omap2420-h4.dts
@@ -50,15 +50,15 @@
label = "bootloader";
reg = <0 0x20000>;
};
- partition@0x20000 {
+ partition@20000 {
label = "params";
reg = <0x20000 0x20000>;
};
- partition@0x40000 {
+ partition@40000 {
label = "kernel";
reg = <0x40000 0x200000>;
};
- partition@0x240000 {
+ partition@240000 {
label = "file-system";
reg = <0x240000 0x3dc0000>;
};
diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts
index 0c514dc..2e88095 100644
--- a/arch/arm/boot/dts/omap3-beagle-xm.dts
+++ b/arch/arm/boot/dts/omap3-beagle-xm.dts
@@ -11,7 +11,7 @@
/ {
model = "TI OMAP3 BeagleBoard xM";
- compatible = "ti,omap3-beagle-xm", "ti,omap3-beagle", "ti,omap3";
+ compatible = "ti,omap3-beagle-xm", "ti,omap36xx", "ti,omap3";
cpus {
cpu@0 {
@@ -69,6 +69,23 @@
};
};
+
+ /* HS USB Port 2 Power */
+ hsusb2_power: hsusb2_power_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "hsusb2_vbus";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&twl_gpio 18 0>; /* GPIO LEDA */
+ startup-delay-us = <70000>;
+ };
+
+ /* HS USB Host PHY on PORT 2 */
+ hsusb2_phy: hsusb2_phy {
+ compatible = "usb-nop-xceiv";
+ reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */
+ vcc-supply = <&hsusb2_power>;
+ };
};
&omap3_pmx_wkup {
@@ -79,6 +96,37 @@
};
};
+&omap3_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &hsusbb2_pins
+ >;
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+ 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */
+ >;
+ };
+
+ hsusbb2_pins: pinmux_hsusbb2_pins {
+ pinctrl-single,pins = <
+ 0x5c0 (PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
+ 0x5c2 (PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
+ 0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
+ 0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
+ 0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
+ 0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
+ 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
+ 0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
+ 0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
+ 0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
+ 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
+ 0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
+ >;
+ };
+};
+
&i2c1 {
clock-frequency = <2600000>;
@@ -148,15 +196,6 @@
power = <50>;
};
-&omap3_pmx_core {
- uart3_pins: pinmux_uart3_pins {
- pinctrl-single,pins = <
- 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
- 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */
- >;
- };
-};
-
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
@@ -166,3 +205,11 @@
pinctrl-names = "default";
pinctrl-0 = <&gpio1_pins>;
};
+
+&usbhshost {
+ port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+ phys = <0 &hsusb2_phy>;
+};
diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts
index dfd8310..fa532aa 100644
--- a/arch/arm/boot/dts/omap3-beagle.dts
+++ b/arch/arm/boot/dts/omap3-beagle.dts
@@ -44,17 +44,6 @@
};
};
- /* HS USB Port 2 RESET */
- hsusb2_reset: hsusb2_reset_reg {
- compatible = "regulator-fixed";
- regulator-name = "hsusb2_reset";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpio5 19 0>; /* gpio_147 */
- startup-delay-us = <70000>;
- enable-active-high;
- };
-
/* HS USB Port 2 Power */
hsusb2_power: hsusb2_power_reg {
compatible = "regulator-fixed";
@@ -68,7 +57,7 @@
/* HS USB Host PHY on PORT 2 */
hsusb2_phy: hsusb2_phy {
compatible = "usb-nop-xceiv";
- reset-supply = <&hsusb2_reset>;
+ reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */
vcc-supply = <&hsusb2_power>;
};
@@ -101,18 +90,18 @@
hsusbb2_pins: pinmux_hsusbb2_pins {
pinctrl-single,pins = <
- 0x5c0 (PIN_OUTPUT | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_clk */
- 0x5c2 (PIN_OUTPUT | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_stp */
- 0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dir */
- 0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_nxt */
- 0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat0 */
- 0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat1 */
- 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat2 */
- 0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat3 */
- 0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat4 */
- 0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat5 */
- 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat6 */
- 0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat7 */
+ 0x5c0 (PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
+ 0x5c2 (PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
+ 0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
+ 0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
+ 0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
+ 0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
+ 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
+ 0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
+ 0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
+ 0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
+ 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
+ 0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
>;
};
@@ -180,3 +169,12 @@
pinctrl-names = "default";
pinctrl-0 = <&gpio1_pins>;
};
+
+&usb_otg_hs {
+ interface-type = <0>;
+ usb-phy = <&usb2_phy>;
+ phys = <&usb2_phy>;
+ phy-names = "usb2-phy";
+ mode = <3>;
+ power = <50>;
+};
diff --git a/arch/arm/boot/dts/omap3-devkit8000.dts b/arch/arm/boot/dts/omap3-devkit8000.dts
index 7ef2827..4665421 100644
--- a/arch/arm/boot/dts/omap3-devkit8000.dts
+++ b/arch/arm/boot/dts/omap3-devkit8000.dts
@@ -125,7 +125,7 @@
nand-bus-width = <16>;
gpmc,device-nand;
- gpmc,sync-clki-ps = <0>;
+ gpmc,sync-clk-ps = <0>;
gpmc,cs-on-ns = <0>;
gpmc,cs-rd-off-ns = <44>;
gpmc,cs-wr-off-ns = <44>;
diff --git a/arch/arm/boot/dts/omap3-evm-37xx.dts b/arch/arm/boot/dts/omap3-evm-37xx.dts
new file mode 100644
index 0000000..4df68ad
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-evm-37xx.dts
@@ -0,0 +1,151 @@
+/*
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "omap36xx.dtsi"
+#include "omap3-evm-common.dtsi"
+
+
+/ {
+ model = "TI OMAP37XX EVM (TMDSEVM3730)";
+ compatible = "ti,omap3-evm-37xx", "ti,omap36xx";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ wl12xx_vmmc: wl12xx_vmmc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&wl12xx_gpio>;
+ };
+};
+
+&omap3_pmx_core {
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ 0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
+ 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
+ 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
+ 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
+ 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
+ 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
+ 0x120 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */
+ 0x122 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */
+ 0x124 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */
+ 0x126 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */
+ >;
+ };
+
+ /* NOTE: Clocked externally, needs INPUT also for sdmmc2_clk.sdmmc2_clk */
+ mmc2_pins: pinmux_mmc2_pins {
+ pinctrl-single,pins = <
+ 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
+ 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
+ 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
+ 0x12e (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
+ 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
+ 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ 0x16e (WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+ 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
+ >;
+ };
+
+ wl12xx_gpio: pinmux_wl12xx_gpio {
+ pinctrl-single,pins = <
+ 0x150 (PIN_OUTPUT | MUX_MODE4) /* uart1_cts.gpio_150 */
+ 0x14e (PIN_INPUT | MUX_MODE4) /* uart1_rts.gpio_149 */
+ >;
+ };
+
+ smsc911x_pins: pinmux_smsc911x_pins {
+ pinctrl-single,pins = <
+ 0x1a2 (PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */
+ >;
+ };
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+};
+
+&gpmc {
+ ranges = <0 0 0x00000000 0x20000000>,
+ <5 0 0x2c000000 0x01000000>;
+
+ nand@0,0 {
+ linux,mtd-name= "hynix,h8kds0un0mer-4em";
+ reg = <0 0 0>;
+ nand-bus-width = <16>;
+ ti,nand-ecc-opt = "bch8";
+
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <44>;
+ gpmc,cs-wr-off-ns = <44>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <34>;
+ gpmc,adv-wr-off-ns = <44>;
+ gpmc,we-off-ns = <40>;
+ gpmc,oe-off-ns = <54>;
+ gpmc,access-ns = <64>;
+ gpmc,rd-cycle-ns = <82>;
+ gpmc,wr-cycle-ns = <82>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "X-Loader";
+ reg = <0 0x80000>;
+ };
+ partition@0x80000 {
+ label = "U-Boot";
+ reg = <0x80000 0x1c0000>;
+ };
+ partition@0x1c0000 {
+ label = "Environment";
+ reg = <0x240000 0x40000>;
+ };
+ partition@0x280000 {
+ label = "Kernel";
+ reg = <0x280000 0x500000>;
+ };
+ partition@0x780000 {
+ label = "Filesystem";
+ reg = <0x780000 0x1f880000>;
+ };
+ };
+
+ ethernet@gpmc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&smsc911x_pins>;
+ };
+};
diff --git a/arch/arm/boot/dts/omap3-evm-common.dtsi b/arch/arm/boot/dts/omap3-evm-common.dtsi
new file mode 100644
index 0000000..b549329
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-evm-common.dtsi
@@ -0,0 +1,94 @@
+/*
+ * Common support for omap3 EVM boards
+ */
+
+#include "omap-gpmc-smsc911x.dtsi"
+
+/ {
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&vcc>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ ledb {
+ label = "omap3evm::ledb";
+ gpios = <&twl_gpio 19 GPIO_ACTIVE_HIGH>; /* LEDB */
+ linux,default-trigger = "default-on";
+ };
+ };
+
+ wl12xx_vmmc: wl12xx_vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "vwl1271";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio5 22 0>; /* gpio150 */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ vin-supply = <&vmmc2>;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <2600000>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+ interrupt-parent = <&intc>;
+ };
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&i2c2 {
+ clock-frequency = <400000>;
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+
+ /*
+ * TVP5146 Video decoder-in for analog input support.
+ */
+ tvp5146@5c {
+ compatible = "ti,tvp5146m2";
+ reg = <0x5c>;
+ };
+};
+
+&mmc1 {
+ vmmc-supply = <&vmmc1>;
+ vmmc_aux-supply = <&vsim>;
+ bus-width = <8>;
+};
+
+&mmc2 {
+ vmmc-supply = <&wl12xx_vmmc>;
+ non-removable;
+ bus-width = <4>;
+ cap-power-off-card;
+};
+
+&twl_gpio {
+ ti,use-leds;
+};
+
+&usb_otg_hs {
+ interface-type = <0>;
+ usb-phy = <&usb2_phy>;
+ mode = <3>;
+ power = <50>;
+};
+
+&gpmc {
+ ethernet@gpmc {
+ interrupt-parent = <&gpio6>;
+ interrupts = <16 8>;
+ reg = <5 0 0xff>;
+ };
+};
diff --git a/arch/arm/boot/dts/omap3-evm.dts b/arch/arm/boot/dts/omap3-evm.dts
index 7d4329d..e10dcd0 100644
--- a/arch/arm/boot/dts/omap3-evm.dts
+++ b/arch/arm/boot/dts/omap3-evm.dts
@@ -8,68 +8,14 @@
/dts-v1/;
#include "omap34xx.dtsi"
+#include "omap3-evm-common.dtsi"
/ {
- model = "TI OMAP3 EVM (OMAP3530, AM/DM37x)";
+ model = "TI OMAP35XX EVM (TMDSEVM3530)";
compatible = "ti,omap3-evm", "ti,omap3";
- cpus {
- cpu@0 {
- cpu0-supply = <&vcc>;
- };
- };
-
memory {
device_type = "memory";
reg = <0x80000000 0x10000000>; /* 256 MB */
};
-
- leds {
- compatible = "gpio-leds";
- ledb {
- label = "omap3evm::ledb";
- gpios = <&twl_gpio 19 GPIO_ACTIVE_HIGH>; /* LEDB */
- linux,default-trigger = "default-on";
- };
- };
-};
-
-&i2c1 {
- clock-frequency = <2600000>;
-
- twl: twl@48 {
- reg = <0x48>;
- interrupts = <7>; /* SYS_NIRQ cascaded to intc */
- interrupt-parent = <&intc>;
- };
-};
-
-#include "twl4030.dtsi"
-#include "twl4030_omap3.dtsi"
-
-&i2c2 {
- clock-frequency = <400000>;
-};
-
-&i2c3 {
- clock-frequency = <400000>;
-
- /*
- * TVP5146 Video decoder-in for analog input support.
- */
- tvp5146@5c {
- compatible = "ti,tvp5146m2";
- reg = <0x5c>;
- };
-};
-
-&twl_gpio {
- ti,use-leds;
-};
-
-&usb_otg_hs {
- interface-type = <0>;
- usb-phy = <&usb2_phy>;
- mode = <3>;
- power = <50>;
};
diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts
new file mode 100644
index 0000000..b9b55c9
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-gta04.dts
@@ -0,0 +1,170 @@
+/*
+ * Copyright (C) 2013 Marek Belisko <marek@goldelico.com>
+ *
+ * Based on omap3-beagle-xm.dts
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "omap36xx.dtsi"
+
+/ {
+ model = "OMAP3 GTA04";
+ compatible = "ti,omap3-gta04", "ti,omap3";
+
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&vcc>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>; /* 512 MB */
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ aux-button {
+ label = "aux";
+ linux,code = <169>;
+ gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+ gpio-key,wakeup;
+ };
+ };
+};
+
+&omap3_pmx_core {
+ uart1_pins: pinmux_uart1_pins {
+ pinctrl-single,pins = <
+ 0x152 (PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */
+ 0x14c (PIN_OUTPUT |MUX_MODE0) /* uart1_tx.uart1_tx */
+ >;
+ };
+
+ uart2_pins: pinmux_uart2_pins {
+ pinctrl-single,pins = <
+ 0x14a (PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */
+ 0x148 (PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx.uart3_rx */
+ 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx.uart3_tx */
+ >;
+ };
+
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ 0x114 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
+ 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
+ 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
+ 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
+ 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
+ 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
+ >;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <2600000>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+ interrupt-parent = <&intc>;
+ };
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&i2c2 {
+ clock-frequency = <400000>;
+
+ /* pressure sensor */
+ bmp085@77 {
+ compatible = "bosch,bmp085";
+ reg = <0x77>;
+ };
+
+ /* leds */
+ tca6507@45 {
+ compatible = "ti,tca6507";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x45>;
+
+ gta04_led0: red_aux@0 {
+ label = "gta04:red:aux";
+ reg = <0x0>;
+ };
+
+ gta04_led1: green_aux@1 {
+ label = "gta04:green:aux";
+ reg = <0x1>;
+ };
+
+ gta04_led3: red_power@3 {
+ label = "gta04:red:power";
+ reg = <0x3>;
+ linux,default-trigger = "default-on";
+ };
+
+ gta04_led4: green_power@4 {
+ label = "gta04:green:power";
+ reg = <0x4>;
+ };
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+};
+
+&usb_otg_hs {
+ interface-type = <0>;
+ usb-phy = <&usb2_phy>;
+ phys = <&usb2_phy>;
+ phy-names = "usb2-phy";
+ mode = <3>;
+ power = <50>;
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <&vmmc1>;
+ vmmc_aux-supply = <&vsim>;
+ bus-width = <4>;
+};
+
+&mmc2 {
+ status = "disabled";
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+};
+
diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi
index 2326d11..ba1e58b 100644
--- a/arch/arm/boot/dts/omap3-igep.dtsi
+++ b/arch/arm/boot/dts/omap3-igep.dtsi
@@ -77,6 +77,8 @@
0x1a2 (PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */
>;
};
+
+ leds_pins: pinmux_leds_pins { };
};
&i2c1 {
@@ -141,3 +143,12 @@
&twl_gpio {
ti,use-leds;
};
+
+&usb_otg_hs {
+ interface-type = <0>;
+ usb-phy = <&usb2_phy>;
+ phys = <&usb2_phy>;
+ phy-names = "usb2-phy";
+ mode = <3>;
+ power = <50>;
+};
diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts
index e8c4828..d5cc792 100644
--- a/arch/arm/boot/dts/omap3-igep0020.dts
+++ b/arch/arm/boot/dts/omap3-igep0020.dts
@@ -10,13 +10,17 @@
*/
#include "omap3-igep.dtsi"
+#include "omap-gpmc-smsc911x.dtsi"
/ {
model = "IGEPv2";
compatible = "isee,omap3-igep0020", "ti,omap3";
leds {
+ pinctrl-names = "default";
+ pinctrl-0 = <&leds_pins>;
compatible = "gpio-leds";
+
boot {
label = "omap3:green:boot";
gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
@@ -41,19 +45,56 @@
};
};
- vddvario: regulator-vddvario {
- compatible = "regulator-fixed";
- regulator-name = "vddvario";
- regulator-always-on;
- };
+ /* HS USB Port 1 Power */
+ hsusb1_power: hsusb1_power_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "hsusb1_vbus";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&twl_gpio 18 GPIO_ACTIVE_LOW>; /* GPIO LEDA */
+ startup-delay-us = <70000>;
+ };
- vdd33a: regulator-vdd33a {
- compatible = "regulator-fixed";
- regulator-name = "vdd33a";
- regulator-always-on;
+ /* HS USB Host PHY on PORT 1 */
+ hsusb1_phy: hsusb1_phy {
+ compatible = "usb-nop-xceiv";
+ reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; /* gpio_24 */
+ vcc-supply = <&hsusb1_power>;
};
};
+&omap3_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &hsusbb1_pins
+ >;
+
+ hsusbb1_pins: pinmux_hsusbb1_pins {
+ pinctrl-single,pins = <
+ 0x5aa (PIN_OUTPUT | MUX_MODE3) /* etk_ctl.hsusb1_clk */
+ 0x5a8 (PIN_OUTPUT | MUX_MODE3) /* etk_clk.hsusb1_stp */
+ 0x5bc (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d8.hsusb1_dir */
+ 0x5be (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d9.hsusb1_nxt */
+ 0x5ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d0.hsusb1_data0 */
+ 0x5ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d1.hsusb1_data1 */
+ 0x5b0 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d2.hsusb1_data2 */
+ 0x5b2 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d3.hsusb1_data7 */
+ 0x5b4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d4.hsusb1_data4 */
+ 0x5b6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d5.hsusb1_data5 */
+ 0x5b8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d6.hsusb1_data6 */
+ 0x5ba (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d7.hsusb1_data3 */
+ >;
+ };
+};
+
+&leds_pins {
+ pinctrl-single,pins = <
+ 0x5c4 (PIN_OUTPUT | MUX_MODE4) /* etk_d12.gpio_26 */
+ 0x5c6 (PIN_OUTPUT | MUX_MODE4) /* etk_d13.gpio_27 */
+ 0x5c8 (PIN_OUTPUT | MUX_MODE4) /* etk_d14.gpio_28 */
+ >;
+};
+
&i2c3 {
clock-frequency = <100000>;
@@ -99,59 +140,37 @@
label = "SPL";
reg = <0 0x100000>;
};
- partition@0x80000 {
+ partition@80000 {
label = "U-Boot";
reg = <0x100000 0x180000>;
};
- partition@0x1c0000 {
+ partition@1c0000 {
label = "Environment";
reg = <0x280000 0x100000>;
};
- partition@0x280000 {
+ partition@280000 {
label = "Kernel";
reg = <0x380000 0x300000>;
};
- partition@0x780000 {
+ partition@780000 {
label = "Filesystem";
reg = <0x680000 0x1f980000>;
};
};
- ethernet@5,0 {
+ ethernet@gpmc {
pinctrl-names = "default";
pinctrl-0 = <&smsc911x_pins>;
- compatible = "smsc,lan9221", "smsc,lan9115";
reg = <5 0 0xff>;
- bank-width = <2>;
-
- gpmc,mux-add-data;
- gpmc,cs-on-ns = <0>;
- gpmc,cs-rd-off-ns = <186>;
- gpmc,cs-wr-off-ns = <186>;
- gpmc,adv-on-ns = <12>;
- gpmc,adv-rd-off-ns = <48>;
- gpmc,adv-wr-off-ns = <48>;
- gpmc,oe-on-ns = <54>;
- gpmc,oe-off-ns = <168>;
- gpmc,we-on-ns = <54>;
- gpmc,we-off-ns = <168>;
- gpmc,rd-cycle-ns = <186>;
- gpmc,wr-cycle-ns = <186>;
- gpmc,access-ns = <114>;
- gpmc,page-burst-access-ns = <6>;
- gpmc,bus-turnaround-ns = <12>;
- gpmc,cycle2cycle-delay-ns = <18>;
- gpmc,wr-data-mux-bus-ns = <90>;
- gpmc,wr-access-ns = <186>;
- gpmc,cycle2cycle-samecsen;
- gpmc,cycle2cycle-diffcsen;
-
interrupt-parent = <&gpio6>;
- interrupts = <16 8>;
- vmmc-supply = <&vddvario>;
- vmmc_aux-supply = <&vdd33a>;
- reg-io-width = <4>;
-
- smsc,save-mac-address;
+ interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
};
};
+
+&usbhshost {
+ port1-mode = "ehci-phy";
+};
+
+&usbhsehci {
+ phys = <&hsusb1_phy>;
+};
diff --git a/arch/arm/boot/dts/omap3-igep0030.dts b/arch/arm/boot/dts/omap3-igep0030.dts
index 644d053..525e6d9 100644
--- a/arch/arm/boot/dts/omap3-igep0030.dts
+++ b/arch/arm/boot/dts/omap3-igep0030.dts
@@ -16,7 +16,10 @@
compatible = "isee,omap3-igep0030", "ti,omap3";
leds {
+ pinctrl-names = "default";
+ pinctrl-0 = <&leds_pins>;
compatible = "gpio-leds";
+
boot {
label = "omap3:green:boot";
gpios = <&twl_gpio 13 GPIO_ACTIVE_LOW>;
@@ -43,6 +46,12 @@
};
};
+&leds_pins {
+ pinctrl-single,pins = <
+ 0x5b0 (PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 */
+ >;
+};
+
&gpmc {
ranges = <0 0 0x00000000 0x20000000>;
@@ -74,19 +83,19 @@
label = "SPL";
reg = <0 0x100000>;
};
- partition@0x80000 {
+ partition@80000 {
label = "U-Boot";
reg = <0x100000 0x180000>;
};
- partition@0x1c0000 {
+ partition@1c0000 {
label = "Environment";
reg = <0x280000 0x100000>;
};
- partition@0x280000 {
+ partition@280000 {
label = "Kernel";
reg = <0x380000 0x300000>;
};
- partition@0x780000 {
+ partition@780000 {
label = "Filesystem";
reg = <0x680000 0x1f980000>;
};
diff --git a/arch/arm/boot/dts/omap3-n9.dts b/arch/arm/boot/dts/omap3-n9.dts
new file mode 100644
index 0000000..39828ce
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-n9.dts
@@ -0,0 +1,18 @@
+/*
+ * omap3-n9.dts - Device Tree file for Nokia N9
+ *
+ * Written by: Aaro Koskinen <aaro.koskinen@iki.fi>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "omap3-n950-n9.dtsi"
+
+/ {
+ model = "Nokia N9";
+ compatible = "nokia,omap3-n9", "ti,omap3";
+};
diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
new file mode 100644
index 0000000..c4f20bf
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -0,0 +1,484 @@
+/*
+ * Copyright (C) 2013 Pavel Machek <pavel@ucw.cz>
+ * Copyright 2013 Aaro Koskinen <aaro.koskinen@iki.fi>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 (or later) as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "omap34xx.dtsi"
+
+/ {
+ model = "Nokia N900";
+ compatible = "nokia,omap3-n900", "ti,omap3";
+
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&vcc>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ camera_lens_cover {
+ label = "Camera Lens Cover";
+ gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* 110 */
+ linux,input-type = <5>; /* EV_SW */
+ linux,code = <0x09>; /* SW_CAMERA_LENS_COVER */
+ gpio-key,wakeup;
+ };
+
+ camera_focus {
+ label = "Camera Focus";
+ gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; /* 68 */
+ linux,code = <0x210>; /* KEY_CAMERA_FOCUS */
+ gpio-key,wakeup;
+ };
+
+ camera_capture {
+ label = "Camera Capture";
+ gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; /* 69 */
+ linux,code = <0xd4>; /* KEY_CAMERA */
+ gpio-key,wakeup;
+ };
+
+ lock_button {
+ label = "Lock Button";
+ gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* 113 */
+ linux,code = <0x98>; /* KEY_SCREENLOCK */
+ gpio-key,wakeup;
+ };
+
+ keypad_slide {
+ label = "Keypad Slide";
+ gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; /* 71 */
+ linux,input-type = <5>; /* EV_SW */
+ linux,code = <0x0a>; /* SW_KEYPAD_SLIDE */
+ gpio-key,wakeup;
+ };
+
+ proximity_sensor {
+ label = "Proximity Sensor";
+ gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>; /* 89 */
+ linux,input-type = <5>; /* EV_SW */
+ linux,code = <0x0b>; /* SW_FRONT_PROXIMITY */
+ };
+ };
+
+};
+
+&omap3_pmx_core {
+ pinctrl-names = "default";
+
+ uart2_pins: pinmux_uart2_pins {
+ pinctrl-single,pins = <
+ 0x14a (PIN_INPUT | MUX_MODE0) /* uart2_rx */
+ 0x148 (PIN_OUTPUT | MUX_MODE0) /* uart2_tx */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx */
+ 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx */
+ >;
+ };
+
+ i2c1_pins: pinmux_i2c1_pins {
+ pinctrl-single,pins = <
+ 0x18a (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
+ 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
+ >;
+ };
+
+ i2c2_pins: pinmux_i2c2_pins {
+ pinctrl-single,pins = <
+ 0x18e (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */
+ 0x190 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */
+ >;
+ };
+
+ i2c3_pins: pinmux_i2c3_pins {
+ pinctrl-single,pins = <
+ 0x192 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
+ 0x194 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
+ >;
+ };
+
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ 0x114 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */
+ 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */
+ 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0 */
+ 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */
+ 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */
+ 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */
+ >;
+ };
+
+ display_pins: pinmux_display_pins {
+ pinctrl-single,pins = <
+ 0x0d4 (PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */
+ >;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
+ clock-frequency = <2200000>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+ interrupt-parent = <&intc>;
+ };
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&vaux1 {
+ regulator-name = "V28";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on; /* due battery cover sensor */
+};
+
+&vaux2 {
+ regulator-name = "VCSI";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+};
+
+&vaux3 {
+ regulator-name = "VMMC2_30";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3000000>;
+};
+
+&vaux4 {
+ regulator-name = "VCAM_ANA_28";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+};
+
+&vmmc1 {
+ regulator-name = "VMMC1";
+ regulator-min-microvolt = <1850000>;
+ regulator-max-microvolt = <3150000>;
+};
+
+&vmmc2 {
+ regulator-name = "V28_A";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on; /* due VIO leak to AIC34 VDDs */
+};
+
+&vpll1 {
+ regulator-name = "VPLL";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+};
+
+&vpll2 {
+ regulator-name = "VSDI_CSI";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+};
+
+&vsim {
+ regulator-name = "VMMC2_IO_18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+};
+
+&vio {
+ regulator-name = "VIO";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+};
+
+&vintana1 {
+ regulator-name = "VINTANA1";
+ /* fixed to 1500000 */
+ regulator-always-on;
+};
+
+&vintana2 {
+ regulator-name = "VINTANA2";
+ regulator-min-microvolt = <2750000>;
+ regulator-max-microvolt = <2750000>;
+ regulator-always-on;
+};
+
+&vintdig {
+ regulator-name = "VINTDIG";
+ /* fixed to 1500000 */
+ regulator-always-on;
+};
+
+&twl {
+ twl_audio: audio {
+ compatible = "ti,twl4030-audio";
+ ti,enable-vibra = <1>;
+ };
+};
+
+&twl_gpio {
+ ti,pullups = <0x0>;
+ ti,pulldowns = <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+
+ clock-frequency = <100000>;
+
+ tlv320aic3x: tlv320aic3x@18 {
+ compatible = "ti,tlv320aic3x";
+ reg = <0x18>;
+ gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
+ ai3x-gpio-func = <
+ 0 /* AIC3X_GPIO1_FUNC_DISABLED */
+ 5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
+ >;
+
+ AVDD-supply = <&vmmc2>;
+ DRVDD-supply = <&vmmc2>;
+ IOVDD-supply = <&vio>;
+ DVDD-supply = <&vio>;
+ };
+
+ tlv320aic3x_aux: tlv320aic3x@19 {
+ compatible = "ti,tlv320aic3x";
+ reg = <0x19>;
+ gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
+
+ AVDD-supply = <&vmmc2>;
+ DRVDD-supply = <&vmmc2>;
+ IOVDD-supply = <&vio>;
+ DVDD-supply = <&vio>;
+ };
+
+ lp5523: lp5523@32 {
+ compatible = "national,lp5523";
+ reg = <0x32>;
+ clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
+ enable-gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
+
+ chan0 {
+ chan-name = "lp5523:kb1";
+ led-cur = /bits/ 8 <50>;
+ max-cur = /bits/ 8 <100>;
+ };
+
+ chan1 {
+ chan-name = "lp5523:kb2";
+ led-cur = /bits/ 8 <50>;
+ max-cur = /bits/ 8 <100>;
+ };
+
+ chan2 {
+ chan-name = "lp5523:kb3";
+ led-cur = /bits/ 8 <50>;
+ max-cur = /bits/ 8 <100>;
+ };
+
+ chan3 {
+ chan-name = "lp5523:kb4";
+ led-cur = /bits/ 8 <50>;
+ max-cur = /bits/ 8 <100>;
+ };
+
+ chan4 {
+ chan-name = "lp5523:b";
+ led-cur = /bits/ 8 <50>;
+ max-cur = /bits/ 8 <100>;
+ };
+
+ chan5 {
+ chan-name = "lp5523:g";
+ led-cur = /bits/ 8 <50>;
+ max-cur = /bits/ 8 <100>;
+ };
+
+ chan6 {
+ chan-name = "lp5523:r";
+ led-cur = /bits/ 8 <50>;
+ max-cur = /bits/ 8 <100>;
+ };
+
+ chan7 {
+ chan-name = "lp5523:kb5";
+ led-cur = /bits/ 8 <50>;
+ max-cur = /bits/ 8 <100>;
+ };
+
+ chan8 {
+ chan-name = "lp5523:kb6";
+ led-cur = /bits/ 8 <50>;
+ max-cur = /bits/ 8 <100>;
+ };
+ };
+
+ bq27200: bq27200@55 {
+ compatible = "ti,bq27200";
+ reg = <0x55>;
+ };
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+
+ clock-frequency = <400000>;
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <&vmmc1>;
+ bus-width = <4>;
+ cd-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* 160 */
+};
+
+&mmc2 {
+ status = "disabled";
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&gpmc {
+ ranges = <0 0 0x04000000 0x10000000>; /* 256MB */
+
+ /* gpio-irq for dma: 65 */
+
+ onenand@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0 0 0x10000000>;
+
+ gpmc,sync-read;
+ gpmc,sync-write;
+ gpmc,burst-length = <16>;
+ gpmc,burst-read;
+ gpmc,burst-wrap;
+ gpmc,burst-write;
+ gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */
+ gpmc,mux-add-data = <2>; /* GPMC_MUX_AD */
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <87>;
+ gpmc,cs-wr-off-ns = <87>;
+ gpmc,adv-on-ns = <0>;
+ gpmc,adv-rd-off-ns = <10>;
+ gpmc,adv-wr-off-ns = <10>;
+ gpmc,oe-on-ns = <15>;
+ gpmc,oe-off-ns = <87>;
+ gpmc,we-on-ns = <0>;
+ gpmc,we-off-ns = <87>;
+ gpmc,rd-cycle-ns = <112>;
+ gpmc,wr-cycle-ns = <112>;
+ gpmc,access-ns = <81>;
+ gpmc,page-burst-access-ns = <15>;
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <0>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,clk-activation-ns = <5>;
+ gpmc,wr-data-mux-bus-ns = <30>;
+ gpmc,wr-access-ns = <81>;
+ gpmc,sync-clk-ps = <15000>;
+
+ /*
+ * MTD partition table corresponding to Nokia's
+ * Maemo 5 (Fremantle) release.
+ */
+ partition@0 {
+ label = "bootloader";
+ reg = <0x00000000 0x00020000>;
+ read-only;
+ };
+ partition@1 {
+ label = "config";
+ reg = <0x00020000 0x00060000>;
+ };
+ partition@2 {
+ label = "log";
+ reg = <0x00080000 0x00040000>;
+ };
+ partition@3 {
+ label = "kernel";
+ reg = <0x000c0000 0x00200000>;
+ };
+ partition@4 {
+ label = "initfs";
+ reg = <0x002c0000 0x00200000>;
+ };
+ partition@5 {
+ label = "rootfs";
+ reg = <0x004c0000 0x0fb40000>;
+ };
+ };
+};
+
+&mcspi1 {
+ /*
+ * For some reason, touchscreen is necessary for screen to work at
+ * all on real hw. It works well without it on emulator.
+ *
+ * Also... order in the device tree actually matters here.
+ */
+ tsc2005@0 {
+ compatible = "tsc2005";
+ spi-max-frequency = <6000000>;
+ reg = <0>;
+ };
+ mipid@2 {
+ compatible = "acx565akm";
+ spi-max-frequency = <6000000>;
+ reg = <2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&display_pins>;
+ };
+};
+
+&usb_otg_hs {
+ interface-type = <0>;
+ usb-phy = <&usb2_phy>;
+ phys = <&usb2_phy>;
+ phy-names = "usb2-phy";
+ mode = <2>;
+ power = <50>;
+};
+
+&uart1 {
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+};
diff --git a/arch/arm/boot/dts/omap3-n950-n9.dtsi b/arch/arm/boot/dts/omap3-n950-n9.dtsi
new file mode 100644
index 0000000..94eb77d
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-n950-n9.dtsi
@@ -0,0 +1,174 @@
+/*
+ * omap3-n950-n9.dtsi - Device Tree file for Nokia N950 & N9 (common stuff)
+ *
+ * Written by: Aaro Koskinen <aaro.koskinen@iki.fi>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "omap36xx.dtsi"
+
+/ {
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&vcc>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x40000000>; /* 1 GB */
+ };
+
+ vemmc: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "VEMMC";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ gpio = <&gpio5 29 0>; /* gpio line 157 */
+ startup-delay-us = <150>;
+ enable-active-high;
+ };
+};
+
+&omap3_pmx_core {
+ mmc2_pins: pinmux_mmc2_pins {
+ pinctrl-single,pins = <
+ 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk */
+ 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd */
+ 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0 */
+ 0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1 */
+ 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2 */
+ 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3 */
+ >;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <2900000>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+ interrupt-parent = <&intc>;
+ };
+};
+
+/include/ "twl4030.dtsi"
+
+&twl {
+ compatible = "ti,twl5031";
+};
+
+&twl_gpio {
+ ti,pullups = <0x000001>; /* BIT(0) */
+ ti,pulldowns = <0x008106>; /* BIT(1) | BIT(2) | BIT(8) | BIT(15) */
+};
+
+&i2c2 {
+ clock-frequency = <400000>;
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+};
+
+&mmc1 {
+ status = "disabled";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+ vmmc-supply = <&vemmc>;
+ bus-width = <4>;
+ ti,non-removable;
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&usb_otg_hs {
+ interface-type = <0>;
+ usb-phy = <&usb2_phy>;
+ phys = <&usb2_phy>;
+ phy-names = "usb2-phy";
+ mode = <3>;
+ power = <50>;
+};
+
+&gpmc {
+ ranges = <0 0 0x04000000 0x20000000>;
+
+ onenand@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0 0 0x20000000>;
+
+ gpmc,sync-read;
+ gpmc,sync-write;
+ gpmc,burst-length = <16>;
+ gpmc,burst-read;
+ gpmc,burst-wrap;
+ gpmc,burst-write;
+ gpmc,device-width = <2>;
+ gpmc,mux-add-data = <2>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <87>;
+ gpmc,cs-wr-off-ns = <87>;
+ gpmc,adv-on-ns = <0>;
+ gpmc,adv-rd-off-ns = <10>;
+ gpmc,adv-wr-off-ns = <10>;
+ gpmc,oe-on-ns = <15>;
+ gpmc,oe-off-ns = <87>;
+ gpmc,we-on-ns = <0>;
+ gpmc,we-off-ns = <87>;
+ gpmc,rd-cycle-ns = <112>;
+ gpmc,wr-cycle-ns = <112>;
+ gpmc,access-ns = <81>;
+ gpmc,page-burst-access-ns = <15>;
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <0>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,clk-activation-ns = <5>;
+ gpmc,wr-data-mux-bus-ns = <30>;
+ gpmc,wr-access-ns = <81>;
+ gpmc,sync-clk-ps = <15000>;
+
+ /*
+ * MTD partition table corresponding to Nokia's MeeGo 1.2
+ * Harmattan release.
+ */
+ partition@0 {
+ label = "bootloader";
+ reg = <0x00000000 0x00100000>;
+ };
+ partition@1 {
+ label = "config";
+ reg = <0x00100000 0x002c0000>;
+ };
+ partition@2 {
+ label = "kernel";
+ reg = <0x003c0000 0x01000000>;
+ };
+ partition@3 {
+ label = "log";
+ reg = <0x013c0000 0x00200000>;
+ };
+ partition@4 {
+ label = "var";
+ reg = <0x015c0000 0x1ca40000>;
+ };
+ partition@5 {
+ label = "moslo";
+ reg = <0x1e000000 0x02000000>;
+ };
+ partition@6 {
+ label = "omap2-onenand";
+ reg = <0x00000000 0x20000000>;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/omap3-n950.dts b/arch/arm/boot/dts/omap3-n950.dts
new file mode 100644
index 0000000..b076a52
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-n950.dts
@@ -0,0 +1,18 @@
+/*
+ * omap3-n950.dts - Device Tree file for Nokia N950
+ *
+ * Written by: Aaro Koskinen <aaro.koskinen@iki.fi>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "omap3-n950-n9.dtsi"
+
+/ {
+ model = "Nokia N950";
+ compatible = "nokia,omap3-n950", "ti,omap3";
+};
diff --git a/arch/arm/boot/dts/omap3-zoom3.dts b/arch/arm/boot/dts/omap3-zoom3.dts
new file mode 100644
index 0000000..15eb9fe
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-zoom3.dts
@@ -0,0 +1,217 @@
+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "omap36xx.dtsi"
+#include "omap-zoom-common.dtsi"
+
+/ {
+ model = "TI Zoom3";
+ compatible = "ti,omap3-zoom3", "ti,omap36xx", "ti,omap3";
+
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&vcc>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>; /* 512 MB */
+ };
+
+ vddvario: regulator-vddvario {
+ compatible = "regulator-fixed";
+ regulator-name = "vddvario";
+ regulator-always-on;
+ };
+
+ vdd33a: regulator-vdd33a {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd33a";
+ regulator-always-on;
+ };
+
+ wl12xx_vmmc: wl12xx_vmmc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&wl12xx_gpio>;
+ compatible = "regulator-fixed";
+ regulator-name = "vwl1271";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio4 5 0>; /* gpio101 */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+};
+
+&omap3_pmx_core {
+ /* REVISIT: twl gpio0 is mmc0_cd */
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ 0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
+ 0x116 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
+ 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
+ 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
+ 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
+ 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
+ >;
+ };
+
+ mmc2_pins: pinmux_mmc2_pins {
+ pinctrl-single,pins = <
+ 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
+ 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
+ 0x12c (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
+ 0x12e (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
+ 0x130 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
+ 0x132 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
+ 0x134 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat4.sdmmc2_dat4 */
+ 0x136 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat5.sdmmc2_dat5 */
+ 0x138 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat6.sdmmc2_dat6 */
+ 0x13a (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat7.sdmmc2_dat7 */
+ >;
+ };
+
+ mmc3_pins: pinmux_mmc3_pins {
+ pinctrl-single,pins = <
+ 0x168 (PIN_INPUT | MUX_MODE4) /* mcbsp1_clkx.gpio_162 WLAN IRQ */
+ 0x1a0 (PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */
+ 0x5a8 (PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */
+ 0x5b4 (PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d4.sdmmc3_dat0 */
+ 0x5b6 (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d5.sdmmc3_dat1 */
+ 0x5b8 (PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d6.sdmmc3_dat2 */
+ 0x5b2 (PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d3.sdmmc3_dat3 */
+ >;
+ };
+
+ uart1_pins: pinmux_uart1_pins {
+ pinctrl-single,pins = <
+ 0x150 (PIN_INPUT | MUX_MODE0) /* uart1_cts.uart1_cts */
+ 0x14e (PIN_OUTPUT | MUX_MODE0) /* uart1_rts.uart1_rts */
+ 0x152 (WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */
+ 0x14c (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_tx */
+ >;
+ };
+
+ uart2_pins: pinmux_uart2_pins {
+ pinctrl-single,pins = <
+ 0x144 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts.uart2_cts */
+ 0x146 (PIN_OUTPUT | MUX_MODE0) /* uart2_rts.uart2_rts */
+ 0x14a (WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */
+ 0x148 (PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ 0x16a (PIN_INPUT_PULLDOWN | MUX_MODE0) /* uart3_cts_rctx.uart3_cts_rctx */
+ 0x16c (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_sd.uart3_rts_sd */
+ 0x16e (WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+ 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
+ >;
+ };
+
+ /* wl12xx GPIO output for WLAN_EN */
+ wl12xx_gpio: pinmux_wl12xx_gpio {
+ pinctrl-single,pins = <
+ 0xea (PIN_OUTPUT| MUX_MODE4) /* cam_d2.gpio_101 */
+ >;
+ };
+};
+
+&omap3_pmx_wkup {
+ wlan_host_wkup: pinmux_wlan_host_wkup_pins {
+ pinctrl-single,pins = <
+ 0x1a (PIN_INPUT_PULLUP | MUX_MODE4) /* sys_clkout1.gpio_10 WLAN_HOST_WKUP */
+ >;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <2600000>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+ interrupt-parent = <&intc>;
+ };
+};
+
+#include "twl4030.dtsi"
+
+&i2c2 {
+ clock-frequency = <400000>;
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+
+ /*
+ * TVP5146 Video decoder-in for analog input support.
+ */
+ tvp5146@5c {
+ compatible = "ti,tvp5146m2";
+ reg = <0x5c>;
+ };
+};
+
+&twl_gpio {
+ ti,use-leds;
+};
+
+&mmc1 {
+ vmmc-supply = <&vmmc1>;
+ vmmc_aux-supply = <&vsim>;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+};
+/*
+&mmc2 {
+ vmmc-supply = <&vmmc2>;
+ ti,non-removable;
+ bus-width = <8>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+};
+*/
+&mmc3 {
+ vmmc-supply = <&wl12xx_vmmc>;
+ non-removable;
+ bus-width = <4>;
+ cap-power-off-card;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins>;
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+};
+
+&uart4 {
+ status = "disabled";
+};
+
+&usb_otg_hs {
+ interface-type = <0>;
+ usb-phy = <&usb2_phy>;
+ mode = <3>;
+ power = <50>;
+};
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index 7d95cda..f3a0c26 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -19,6 +19,9 @@
interrupt-parent = <&intc>;
aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
@@ -37,6 +40,7 @@
pmu {
compatible = "arm,cortex-a8-pmu";
+ reg = <0x54000000 0x800000>;
interrupts = <3>;
ti,hwmods = "debugss";
};
@@ -71,6 +75,8 @@
*/
ocp {
compatible = "simple-bus";
+ reg = <0x68000000 0x10000>;
+ interrupts = <9 10>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
@@ -107,17 +113,21 @@
reg = <0x48002030 0x05cc>;
#address-cells = <1>;
#size-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
pinctrl-single,register-width = <16>;
- pinctrl-single,function-mask = <0x7f1f>;
+ pinctrl-single,function-mask = <0xff1f>;
};
- omap3_pmx_wkup: pinmux@0x48002a00 {
+ omap3_pmx_wkup: pinmux@48002a00 {
compatible = "ti,omap3-padconf", "pinctrl-single";
reg = <0x48002a00 0x5c>;
#address-cells = <1>;
#size-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
pinctrl-single,register-width = <16>;
- pinctrl-single,function-mask = <0x7f1f>;
+ pinctrl-single,function-mask = <0xff1f>;
};
gpio1: gpio@48310000 {
@@ -189,24 +199,40 @@
uart1: serial@4806a000 {
compatible = "ti,omap3-uart";
+ reg = <0x4806a000 0x2000>;
+ interrupts = <72>;
+ dmas = <&sdma 49 &sdma 50>;
+ dma-names = "tx", "rx";
ti,hwmods = "uart1";
clock-frequency = <48000000>;
};
uart2: serial@4806c000 {
compatible = "ti,omap3-uart";
+ reg = <0x4806c000 0x400>;
+ interrupts = <73>;
+ dmas = <&sdma 51 &sdma 52>;
+ dma-names = "tx", "rx";
ti,hwmods = "uart2";
clock-frequency = <48000000>;
};
uart3: serial@49020000 {
compatible = "ti,omap3-uart";
+ reg = <0x49020000 0x400>;
+ interrupts = <74>;
+ dmas = <&sdma 53 &sdma 54>;
+ dma-names = "tx", "rx";
ti,hwmods = "uart3";
clock-frequency = <48000000>;
};
i2c1: i2c@48070000 {
compatible = "ti,omap3-i2c";
+ reg = <0x48070000 0x80>;
+ interrupts = <56>;
+ dmas = <&sdma 27 &sdma 28>;
+ dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "i2c1";
@@ -214,6 +240,10 @@
i2c2: i2c@48072000 {
compatible = "ti,omap3-i2c";
+ reg = <0x48072000 0x80>;
+ interrupts = <57>;
+ dmas = <&sdma 29 &sdma 30>;
+ dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "i2c2";
@@ -221,6 +251,10 @@
i2c3: i2c@48060000 {
compatible = "ti,omap3-i2c";
+ reg = <0x48060000 0x80>;
+ interrupts = <61>;
+ dmas = <&sdma 25 &sdma 26>;
+ dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "i2c3";
@@ -228,6 +262,8 @@
mcspi1: spi@48098000 {
compatible = "ti,omap2-mcspi";
+ reg = <0x48098000 0x100>;
+ interrupts = <65>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "mcspi1";
@@ -246,6 +282,8 @@
mcspi2: spi@4809a000 {
compatible = "ti,omap2-mcspi";
+ reg = <0x4809a000 0x100>;
+ interrupts = <66>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "mcspi2";
@@ -259,6 +297,8 @@
mcspi3: spi@480b8000 {
compatible = "ti,omap2-mcspi";
+ reg = <0x480b8000 0x100>;
+ interrupts = <91>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "mcspi3";
@@ -272,6 +312,8 @@
mcspi4: spi@480ba000 {
compatible = "ti,omap2-mcspi";
+ reg = <0x480ba000 0x100>;
+ interrupts = <48>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "mcspi4";
@@ -280,8 +322,17 @@
dma-names = "tx0", "rx0";
};
+ hdqw1w: 1w@480b2000 {
+ compatible = "ti,omap3-1w";
+ reg = <0x480b2000 0x1000>;
+ interrupts = <58>;
+ ti,hwmods = "hdq1w";
+ };
+
mmc1: mmc@4809c000 {
compatible = "ti,omap3-hsmmc";
+ reg = <0x4809c000 0x200>;
+ interrupts = <83>;
ti,hwmods = "mmc1";
ti,dual-volt;
dmas = <&sdma 61>, <&sdma 62>;
@@ -290,6 +341,8 @@
mmc2: mmc@480b4000 {
compatible = "ti,omap3-hsmmc";
+ reg = <0x480b4000 0x200>;
+ interrupts = <86>;
ti,hwmods = "mmc2";
dmas = <&sdma 47>, <&sdma 48>;
dma-names = "tx", "rx";
@@ -297,6 +350,8 @@
mmc3: mmc@480ad000 {
compatible = "ti,omap3-hsmmc";
+ reg = <0x480ad000 0x200>;
+ interrupts = <94>;
ti,hwmods = "mmc3";
dmas = <&sdma 77>, <&sdma 78>;
dma-names = "tx", "rx";
@@ -304,6 +359,7 @@
wdt2: wdt@48314000 {
compatible = "ti,omap3-wdt";
+ reg = <0x48314000 0x80>;
ti,hwmods = "wd_timer2";
};
diff --git a/arch/arm/boot/dts/omap3430-sdp.dts b/arch/arm/boot/dts/omap3430-sdp.dts
index e2249bc..281914e 100644
--- a/arch/arm/boot/dts/omap3430-sdp.dts
+++ b/arch/arm/boot/dts/omap3430-sdp.dts
@@ -84,15 +84,15 @@
label = "bootloader-nor";
reg = <0 0x40000>;
};
- partition@0x40000 {
+ partition@40000 {
label = "params-nor";
reg = <0x40000 0x40000>;
};
- partition@0x80000 {
+ partition@80000 {
label = "kernel-nor";
reg = <0x80000 0x200000>;
};
- partition@0x280000 {
+ partition@280000 {
label = "filesystem-nor";
reg = <0x240000 0x7d80000>;
};
@@ -125,19 +125,19 @@
label = "xloader-nand";
reg = <0 0x80000>;
};
- partition@0x80000 {
+ partition@80000 {
label = "bootloader-nand";
reg = <0x80000 0x140000>;
};
- partition@0x1c0000 {
+ partition@1c0000 {
label = "params-nand";
reg = <0x1c0000 0xc0000>;
};
- partition@0x280000 {
+ partition@280000 {
label = "kernel-nand";
reg = <0x280000 0x500000>;
};
- partition@0x780000 {
+ partition@780000 {
label = "filesystem-nand";
reg = <0x780000 0x7880000>;
};
@@ -170,19 +170,19 @@
label = "xloader-onenand";
reg = <0 0x80000>;
};
- partition@0x80000 {
+ partition@80000 {
label = "bootloader-onenand";
reg = <0x80000 0x40000>;
};
- partition@0xc0000 {
+ partition@c0000 {
label = "params-onenand";
reg = <0xc0000 0x20000>;
};
- partition@0xe0000 {
+ partition@e0000 {
label = "kernel-onenand";
reg = <0xe0000 0x200000>;
};
- partition@0x2e0000 {
+ partition@2e0000 {
label = "filesystem-onenand";
reg = <0x2e0000 0xfd20000>;
};
diff --git a/arch/arm/boot/dts/omap36xx.dtsi b/arch/arm/boot/dts/omap36xx.dtsi
index f8b3765..380c22e 100644
--- a/arch/arm/boot/dts/omap36xx.dtsi
+++ b/arch/arm/boot/dts/omap36xx.dtsi
@@ -31,6 +31,10 @@
ocp {
uart4: serial@49042000 {
compatible = "ti,omap3-uart";
+ reg = <0x49042000 0x400>;
+ interrupts = <80>;
+ dmas = <&sdma 81 &sdma 82>;
+ dma-names = "tx", "rx";
ti,hwmods = "uart4";
clock-frequency = <48000000>;
};
diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
index 814ab67..3e6801c 100644
--- a/arch/arm/boot/dts/omap4-panda-common.dtsi
+++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
@@ -60,22 +60,6 @@
"AFMR", "Line In";
};
- /*
- * Temp hack: Need to be replaced with the proper gpio-controlled
- * reset driver as soon it will be merged.
- * http://thread.gmane.org/gmane.linux.drivers.devicetree/36830
- */
- /* HS USB Port 1 RESET */
- hsusb1_reset: hsusb1_reset_reg {
- compatible = "regulator-fixed";
- regulator-name = "hsusb1_reset";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpio2 30 0>; /* gpio_62 */
- startup-delay-us = <70000>;
- enable-active-high;
- };
-
/* HS USB Port 1 Power */
hsusb1_power: hsusb1_power_reg {
compatible = "regulator-fixed";
@@ -97,7 +81,7 @@
/* HS USB Host PHY on PORT 1 */
hsusb1_phy: hsusb1_phy {
compatible = "usb-nop-xceiv";
- reset-supply = <&hsusb1_reset>;
+ reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>; /* gpio_62 */
vcc-supply = <&hsusb1_power>;
/**
* FIXME:
@@ -122,23 +106,9 @@
};
};
-&omap4_pmx_wkup {
- pinctrl-names = "default";
- pinctrl-0 = <
- &twl6030_wkup_pins
- >;
-
- twl6030_wkup_pins: pinmux_twl6030_wkup_pins {
- pinctrl-single,pins = <
- 0x14 (PIN_OUTPUT | MUX_MODE2) /* fref_clk0_out.sys_drm_msecure */
- >;
- };
-};
-
&omap4_pmx_core {
pinctrl-names = "default";
pinctrl-0 = <
- &twl6030_pins
&twl6040_pins
&mcpdm_pins
&mcbsp1_pins
@@ -147,12 +117,6 @@
&hsusbb1_pins
>;
- twl6030_pins: pinmux_twl6030_pins {
- pinctrl-single,pins = <
- 0x15e (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1.sys_nirq1 */
- >;
- };
-
twl6040_pins: pinmux_twl6040_pins {
pinctrl-single,pins = <
0xe0 (PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */
@@ -305,6 +269,7 @@
};
#include "twl6030.dtsi"
+#include "twl6030_omap4.dtsi"
&i2c2 {
pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/omap4-panda-es.dts
index 56c4354..816d1c9 100644
--- a/arch/arm/boot/dts/omap4-panda-es.dts
+++ b/arch/arm/boot/dts/omap4-panda-es.dts
@@ -62,3 +62,7 @@
gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
};
};
+
+&gpio1 {
+ ti,no-reset-on-init;
+};
diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts
index 4f78380..5fc3f43 100644
--- a/arch/arm/boot/dts/omap4-sdp.dts
+++ b/arch/arm/boot/dts/omap4-sdp.dts
@@ -155,23 +155,9 @@
};
};
-&omap4_pmx_wkup {
- pinctrl-names = "default";
- pinctrl-0 = <
- &twl6030_wkup_pins
- >;
-
- twl6030_wkup_pins: pinmux_twl6030_wkup_pins {
- pinctrl-single,pins = <
- 0x14 (PIN_OUTPUT | MUX_MODE2) /* fref_clk0_out.sys_drm_msecure */
- >;
- };
-};
-
&omap4_pmx_core {
pinctrl-names = "default";
pinctrl-0 = <
- &twl6030_pins
&twl6040_pins
&mcpdm_pins
&dmic_pins
@@ -206,12 +192,6 @@
>;
};
- twl6030_pins: pinmux_twl6030_pins {
- pinctrl-single,pins = <
- 0x15e (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1.sys_nirq1 */
- >;
- };
-
twl6040_pins: pinmux_twl6040_pins {
pinctrl-single,pins = <
0xe0 (PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */
@@ -370,6 +350,7 @@
};
#include "twl6030.dtsi"
+#include "twl6030_omap4.dtsi"
&i2c2 {
pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index 22d9f2b..e8d97b4 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -17,6 +17,10 @@
interrupt-parent = <&gic>;
aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ i2c3 = &i2c4;
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
@@ -56,7 +60,7 @@
cache-level = <2>;
};
- local-timer@0x48240600 {
+ local-timer@48240600 {
compatible = "arm,cortex-a9-twd-timer";
reg = <0x48240600 0x20>;
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>;
@@ -114,6 +118,8 @@
reg = <0x4a100040 0x0196>;
#address-cells = <1>;
#size-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
pinctrl-single,register-width = <16>;
pinctrl-single,function-mask = <0x7fff>;
};
@@ -122,6 +128,8 @@
reg = <0x4a31e040 0x0038>;
#address-cells = <1>;
#size-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
pinctrl-single,register-width = <16>;
pinctrl-single,function-mask = <0x7fff>;
};
@@ -214,6 +222,7 @@
gpmc,num-cs = <8>;
gpmc,num-waitpins = <4>;
ti,hwmods = "gpmc";
+ ti,no-idle-on-init;
};
uart1: serial@4806a000 {
@@ -492,6 +501,7 @@
reg = <0x4c000000 0x100>;
interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "emif1";
+ ti,no-idle-on-init;
phy-type = <1>;
hw-caps-read-idle-ctrl;
hw-caps-ll-interface;
@@ -503,6 +513,7 @@
reg = <0x4d000000 0x100>;
interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "emif2";
+ ti,no-idle-on-init;
phy-type = <1>;
hw-caps-read-idle-ctrl;
hw-caps-ll-interface;
@@ -663,5 +674,23 @@
ram-bits = <12>;
ti,has-mailbox;
};
+
+ aes: aes@4b501000 {
+ compatible = "ti,omap4-aes";
+ ti,hwmods = "aes";
+ reg = <0x4b501000 0xa0>;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&sdma 111>, <&sdma 110>;
+ dma-names = "tx", "rx";
+ };
+
+ des: des@480a5000 {
+ compatible = "ti,omap4-des";
+ ti,hwmods = "des";
+ reg = <0x480a5000 0xa0>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&sdma 117>, <&sdma 116>;
+ dma-names = "tx", "rx";
+ };
};
};
diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts
index 65d7b60..002fa70 100644
--- a/arch/arm/boot/dts/omap5-uevm.dts
+++ b/arch/arm/boot/dts/omap5-uevm.dts
@@ -27,21 +27,10 @@
regulator-max-microvolt = <3000000>;
};
- /* HS USB Port 2 RESET */
- hsusb2_reset: hsusb2_reset_reg {
- compatible = "regulator-fixed";
- regulator-name = "hsusb2_reset";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 HUB_NRESET */
- startup-delay-us = <70000>;
- enable-active-high;
- };
-
/* HS USB Host PHY on PORT 2 */
hsusb2_phy: hsusb2_phy {
compatible = "usb-nop-xceiv";
- reset-supply = <&hsusb2_reset>;
+ reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
/**
* FIXME
* Put the right clock phandle here when available
@@ -51,21 +40,10 @@
clock-frequency = <19200000>;
};
- /* HS USB Port 3 RESET */
- hsusb3_reset: hsusb3_reset_reg {
- compatible = "regulator-fixed";
- regulator-name = "hsusb3_reset";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>; /* gpio3_79 ETH_NRESET */
- startup-delay-us = <70000>;
- enable-active-high;
- };
-
/* HS USB Host PHY on PORT 3 */
hsusb3_phy: hsusb3_phy {
compatible = "usb-nop-xceiv";
- reset-supply = <&hsusb3_reset>;
+ reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */
};
leds {
@@ -84,7 +62,6 @@
pinctrl-0 = <
&twl6040_pins
&mcpdm_pins
- &dmic_pins
&mcbsp1_pins
&mcbsp2_pins
&usbhost_pins
@@ -93,7 +70,7 @@
twl6040_pins: pinmux_twl6040_pins {
pinctrl-single,pins = <
- 0x18a (PIN_OUTPUT | MUX_MODE6) /* perslimbus2_clock.gpio5_145 */
+ 0x17e (PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */
>;
};
@@ -107,15 +84,6 @@
>;
};
- dmic_pins: pinmux_dmic_pins {
- pinctrl-single,pins = <
- 0x144 (PIN_INPUT | MUX_MODE0) /* abedmic_din1.abedmic_din1 */
- 0x146 (PIN_INPUT | MUX_MODE0) /* abedmic_din2.abedmic_din2 */
- 0x148 (PIN_INPUT | MUX_MODE0) /* abedmic_din3.abedmic_din3 */
- 0x14a (PIN_OUTPUT | MUX_MODE0) /* abedmic_clk1.abedmic_clk1 */
- >;
- };
-
mcbsp1_pins: pinmux_mcbsp1_pins {
pinctrl-single,pins = <
0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */
@@ -153,25 +121,25 @@
0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */
- 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs */
+ 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */
>;
};
mcspi3_pins: pinmux_mcspi3_pins {
pinctrl-single,pins = <
- 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi2_somi */
- 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi2_cs */
- 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi2_simo */
- 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi2_clk */
+ 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi3_somi */
+ 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */
+ 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi3_simo */
+ 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi3_clk */
>;
};
mcspi4_pins: pinmux_mcspi4_pins {
pinctrl-single,pins = <
- 0x164 (PIN_INPUT | MUX_MODE1) /* mcspi2_clk */
- 0x168 (PIN_INPUT | MUX_MODE1) /* mcspi2_simo */
- 0x16a (PIN_INPUT | MUX_MODE1) /* mcspi2_somi */
- 0x16c (PIN_INPUT | MUX_MODE1) /* mcspi2_cs */
+ 0x164 (PIN_INPUT | MUX_MODE1) /* mcspi4_clk */
+ 0x168 (PIN_INPUT | MUX_MODE1) /* mcspi4_simo */
+ 0x16a (PIN_INPUT | MUX_MODE1) /* mcspi4_somi */
+ 0x16c (PIN_INPUT | MUX_MODE1) /* mcspi4_cs0 */
>;
};
@@ -271,6 +239,14 @@
reg = <0x48>;
interrupt-controller;
#interrupt-cells = <2>;
+ ti,system-power-controller;
+
+ extcon_usb3: palmas_usb {
+ compatible = "ti,palmas-usb-vid";
+ ti,enable-vbus-detection;
+ ti,enable-id-detection;
+ ti,wakeup;
+ };
palmas_pmic {
compatible = "ti,palmas-pmic";
@@ -334,15 +310,22 @@
ti,smps-range = <0x80>;
};
- smps10_reg: smps10 {
+ smps10_out2_reg: smps10_out2 {
/* VBUS_5V_OTG */
- regulator-name = "smps10";
+ regulator-name = "smps10_out2";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
regulator-boot-on;
};
+ smps10_out1_reg: smps10_out1 {
+ /* VBUS_5V_OTG */
+ regulator-name = "smps10_out1";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
ldo1_reg: ldo1 {
/* VDDAPHY_CAM: vdda_csiport */
regulator-name = "ldo1";
@@ -470,6 +453,11 @@
phys = <0 &hsusb2_phy &hsusb3_phy>;
};
+&usb3 {
+ extcon = <&extcon_usb3>;
+ vbus-supply = <&smps10_out1_reg>;
+};
+
&mcspi1 {
};
@@ -503,3 +491,7 @@
pinctrl-names = "default";
pinctrl-0 = <&uart5_pins>;
};
+
+&cpu0 {
+ cpu0-supply = <&smps123_reg>;
+};
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index 7cdea1b..154d92f 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -21,6 +21,11 @@
interrupt-parent = <&gic>;
aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ i2c3 = &i2c4;
+ i2c4 = &i2c5;
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
@@ -33,10 +38,17 @@
#address-cells = <1>;
#size-cells = <0>;
- cpu@0 {
+ cpu0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a15";
reg = <0x0>;
+
+ operating-points = <
+ /* kHz uV */
+ 500000 880000
+ 1000000 1060000
+ 1500000 1250000
+ >;
};
cpu@1 {
device_type = "cpu";
@@ -52,7 +64,6 @@
<GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>;
- clock-frequency = <6144000>;
};
gic: interrupt-controller@48211000 {
@@ -604,9 +615,10 @@
ti,hwmods = "wd_timer2";
};
- emif1: emif@0x4c000000 {
+ emif1: emif@4c000000 {
compatible = "ti,emif-4d5";
ti,hwmods = "emif1";
+ ti,no-idle-on-init;
phy-type = <2>; /* DDR PHY type: Intelli PHY */
reg = <0x4c000000 0x400>;
interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
@@ -615,9 +627,10 @@
hw-caps-temp-alert;
};
- emif2: emif@0x4d000000 {
+ emif2: emif@4d000000 {
compatible = "ti,emif-4d5";
ti,hwmods = "emif2";
+ ti,no-idle-on-init;
phy-type = <2>; /* DDR PHY type: Intelli PHY */
reg = <0x4d000000 0x400>;
interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
@@ -634,7 +647,7 @@
ti,type = <2>;
};
- omap_dwc3@4a020000 {
+ usb3: omap_dwc3@4a020000 {
compatible = "ti,dwc3";
ti,hwmods = "usb_otg_ss";
reg = <0x4a020000 0x10000>;
@@ -648,6 +661,7 @@
reg = <0x4a030000 0x10000>;
interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
usb-phy = <&usb2_phy>, <&usb3_phy>;
+ dr_mode = "peripheral";
tx-fifo-resize;
};
};
diff --git a/arch/arm/boot/dts/r8a73a4-ape6evm-reference.dts b/arch/arm/boot/dts/r8a73a4-ape6evm-reference.dts
index f444624..9443e93 100644
--- a/arch/arm/boot/dts/r8a73a4-ape6evm-reference.dts
+++ b/arch/arm/boot/dts/r8a73a4-ape6evm-reference.dts
@@ -10,6 +10,7 @@
/dts-v1/;
/include/ "r8a73a4.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "APE6EVM";
@@ -24,6 +25,34 @@
reg = <0 0x40000000 0 0x40000000>;
};
+ vcc_mmc0: regulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "MMC0 Vcc";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ vcc_sdhi0: regulator@1 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "SDHI0 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pfc 76 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ /* Common 3.3V rail, used by several devices on APE6EVM */
+ ape6evm_fixed_3v3: regulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
lbsc {
compatible = "simple-bus";
#address-cells = <1>;
@@ -33,6 +62,7 @@
};
&i2c5 {
+ status = "okay";
vdd_dvfs: max8973@1b {
compatible = "maxim,max8973";
reg = <0x1b>;
@@ -62,4 +92,47 @@
renesas,groups = "scifa0_data";
renesas,function = "scifa0";
};
+
+ mmc0_pins: mmcif {
+ renesas,groups = "mmc0_data8", "mmc0_ctrl";
+ renesas,function = "mmc0";
+ };
+
+ sdhi0_pins: sdhi0 {
+ renesas,groups = "sdhi0_data4", "sdhi0_ctrl", "sdhi0_cd";
+ renesas,function = "sdhi0";
+ };
+
+ sdhi1_pins: sdhi1 {
+ renesas,groups = "sdhi1_data4", "sdhi1_ctrl";
+ renesas,function = "sdhi1";
+ };
+};
+
+&mmcif0 {
+ vmmc-supply = <&vcc_mmc0>;
+ bus-width = <8>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ status = "okay";
+};
+
+&sdhi0 {
+ vmmc-supply = <&vcc_sdhi0>;
+ bus-width = <4>;
+ toshiba,mmc-wrprotect-disable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhi0_pins>;
+ status = "okay";
+};
+
+&sdhi1 {
+ vmmc-supply = <&ape6evm_fixed_3v3>;
+ bus-width = <4>;
+ broken-cd;
+ toshiba,mmc-wrprotect-disable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhi1_pins>;
+ status = "okay";
};
diff --git a/arch/arm/boot/dts/r8a73a4-ape6evm.dts b/arch/arm/boot/dts/r8a73a4-ape6evm.dts
index 72f867e..91436b5 100644
--- a/arch/arm/boot/dts/r8a73a4-ape6evm.dts
+++ b/arch/arm/boot/dts/r8a73a4-ape6evm.dts
@@ -52,6 +52,7 @@
};
&i2c5 {
+ status = "okay";
vdd_dvfs: max8973@1b {
compatible = "maxim,max8973";
reg = <0x1b>;
diff --git a/arch/arm/boot/dts/r8a73a4.dtsi b/arch/arm/boot/dts/r8a73a4.dtsi
index 658fcc5..287e047 100644
--- a/arch/arm/boot/dts/r8a73a4.dtsi
+++ b/arch/arm/boot/dts/r8a73a4.dtsi
@@ -78,6 +78,49 @@
<0 56 4>, <0 57 4>;
};
+ dmac: dma-multiplexer@0 {
+ compatible = "renesas,shdma-mux";
+ #dma-cells = <1>;
+ dma-channels = <20>;
+ dma-requests = <256>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ dma0: dma-controller@e6700020 {
+ compatible = "renesas,shdma-r8a73a4";
+ reg = <0 0xe6700020 0 0x89e0>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 220 4
+ 0 200 4
+ 0 201 4
+ 0 202 4
+ 0 203 4
+ 0 204 4
+ 0 205 4
+ 0 206 4
+ 0 207 4
+ 0 208 4
+ 0 209 4
+ 0 210 4
+ 0 211 4
+ 0 212 4
+ 0 213 4
+ 0 214 4
+ 0 215 4
+ 0 216 4
+ 0 217 4
+ 0 218 4
+ 0 219 4>;
+ interrupt-names = "error",
+ "ch0", "ch1", "ch2", "ch3",
+ "ch4", "ch5", "ch6", "ch7",
+ "ch8", "ch9", "ch10", "ch11",
+ "ch12", "ch13", "ch14", "ch15",
+ "ch16", "ch17", "ch18", "ch19";
+ };
+ };
+
thermal@e61f0000 {
compatible = "renesas,rcar-thermal";
reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>,
@@ -93,6 +136,7 @@
reg = <0 0xe6500000 0 0x428>;
interrupt-parent = <&gic>;
interrupts = <0 174 0x4>;
+ status = "disabled";
};
i2c1: i2c@e6510000 {
@@ -102,6 +146,7 @@
reg = <0 0xe6510000 0 0x428>;
interrupt-parent = <&gic>;
interrupts = <0 175 0x4>;
+ status = "disabled";
};
i2c2: i2c@e6520000 {
@@ -111,6 +156,7 @@
reg = <0 0xe6520000 0 0x428>;
interrupt-parent = <&gic>;
interrupts = <0 176 0x4>;
+ status = "disabled";
};
i2c3: i2c@e6530000 {
@@ -120,6 +166,7 @@
reg = <0 0xe6530000 0 0x428>;
interrupt-parent = <&gic>;
interrupts = <0 177 0x4>;
+ status = "disabled";
};
i2c4: i2c@e6540000 {
@@ -129,6 +176,7 @@
reg = <0 0xe6540000 0 0x428>;
interrupt-parent = <&gic>;
interrupts = <0 178 0x4>;
+ status = "disabled";
};
i2c5: i2c@e60b0000 {
@@ -138,6 +186,7 @@
reg = <0 0xe60b0000 0 0x428>;
interrupt-parent = <&gic>;
interrupts = <0 179 0x4>;
+ status = "disabled";
};
i2c6: i2c@e6550000 {
@@ -147,6 +196,7 @@
reg = <0 0xe6550000 0 0x428>;
interrupt-parent = <&gic>;
interrupts = <0 184 0x4>;
+ status = "disabled";
};
i2c7: i2c@e6560000 {
@@ -156,6 +206,7 @@
reg = <0 0xe6560000 0 0x428>;
interrupt-parent = <&gic>;
interrupts = <0 185 0x4>;
+ status = "disabled";
};
i2c8: i2c@e6570000 {
@@ -165,6 +216,7 @@
reg = <0 0xe6570000 0 0x428>;
interrupt-parent = <&gic>;
interrupts = <0 173 0x4>;
+ status = "disabled";
};
mmcif0: mmcif@ee200000 {
diff --git a/arch/arm/boot/dts/r8a7740-armadillo800eva-reference.dts b/arch/arm/boot/dts/r8a7740-armadillo800eva-reference.dts
index c638e4a..1c56c5e 100644
--- a/arch/arm/boot/dts/r8a7740-armadillo800eva-reference.dts
+++ b/arch/arm/boot/dts/r8a7740-armadillo800eva-reference.dts
@@ -11,6 +11,7 @@
/dts-v1/;
/include/ "r8a7740.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
/ {
model = "armadillo 800 eva reference";
@@ -34,6 +35,33 @@
regulator-boot-on;
};
+ vcc_sdhi0: regulator@1 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "SDHI0 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pfc 75 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vccq_sdhi0: regulator@2 {
+ compatible = "regulator-gpio";
+
+ regulator-name = "SDHI0 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_sdhi0>;
+
+ enable-gpio = <&pfc 74 GPIO_ACTIVE_HIGH>;
+ gpios = <&pfc 17 GPIO_ACTIVE_HIGH>;
+ states = <3300000 0
+ 1800000 1>;
+
+ enable-active-high;
+ };
+
leds {
compatible = "gpio-leds";
led1 {
@@ -49,9 +77,19 @@
gpios = <&pfc 177 GPIO_ACTIVE_HIGH>;
};
};
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&tpu 2 33333 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 1 2 4 8 16 32 64 128 255>;
+ default-brightness-level = <9>;
+ pinctrl-0 = <&backlight_pins>;
+ pinctrl-names = "default";
+ };
};
&i2c0 {
+ status = "okay";
touchscreen: st1232@55 {
compatible = "sitronix,st1232";
reg = <0x55>;
@@ -76,4 +114,44 @@
renesas,groups = "intc_irq10";
renesas,function = "intc";
};
+
+ backlight_pins: backlight {
+ renesas,groups = "tpu0_to2_1";
+ renesas,function = "tpu0";
+ };
+
+ mmc0_pins: mmc0 {
+ renesas,groups = "mmc0_data8_1", "mmc0_ctrl_1";
+ renesas,function = "mmc0";
+ };
+
+ sdhi0_pins: sdhi0 {
+ renesas,groups = "sdhi0_data4", "sdhi0_ctrl", "sdhi0_wp";
+ renesas,function = "sdhi0";
+ };
+};
+
+&tpu {
+ status = "okay";
+};
+
+&mmcif0 {
+ pinctrl-0 = <&mmc0_pins>;
+ pinctrl-names = "default";
+
+ vmmc-supply = <®_3p3v>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&sdhi0 {
+ pinctrl-0 = <&sdhi0_pins>;
+ pinctrl-names = "default";
+
+ vmmc-supply = <&vcc_sdhi0>;
+ vqmmc-supply = <&vccq_sdhi0>;
+ bus-width = <4>;
+ cd-gpios = <&pfc 167 GPIO_ACTIVE_LOW>;
+ status = "okay";
};
diff --git a/arch/arm/boot/dts/r8a7740.dtsi b/arch/arm/boot/dts/r8a7740.dtsi
index 44d3d52..ae1e230 100644
--- a/arch/arm/boot/dts/r8a7740.dtsi
+++ b/arch/arm/boot/dts/r8a7740.dtsi
@@ -131,6 +131,7 @@
0 202 0x4
0 203 0x4
0 204 0x4>;
+ status = "disabled";
};
i2c1: i2c@e6c20000 {
@@ -143,6 +144,7 @@
0 71 0x4
0 72 0x4
0 73 0x4>;
+ status = "disabled";
};
pfc: pfc@e6050000 {
@@ -159,4 +161,37 @@
status = "disabled";
#pwm-cells = <3>;
};
+
+ mmcif0: mmcif@e6bd0000 {
+ compatible = "renesas,sh-mmcif";
+ reg = <0xe6bd0000 0x100>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 56 4
+ 0 57 4>;
+ status = "disabled";
+ };
+
+ sdhi0: sdhi@e6850000 {
+ compatible = "renesas,sdhi-r8a7740";
+ reg = <0xe6850000 0x100>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 117 4
+ 0 118 4
+ 0 119 4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ status = "disabled";
+ };
+
+ sdhi1: sdhi@e6860000 {
+ compatible = "renesas,sdhi-r8a7740";
+ reg = <0xe6860000 0x100>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 121 4
+ 0 122 4
+ 0 123 4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ status = "disabled";
+ };
};
diff --git a/arch/arm/boot/dts/r8a7778-bockw-reference.dts b/arch/arm/boot/dts/r8a7778-bockw-reference.dts
index 9bb903a..969e386 100644
--- a/arch/arm/boot/dts/r8a7778-bockw-reference.dts
+++ b/arch/arm/boot/dts/r8a7778-bockw-reference.dts
@@ -22,11 +22,36 @@
compatible = "renesas,bockw-reference", "renesas,r8a7778";
chosen {
- bootargs = "console=ttySC0,115200 ignore_loglevel rw";
+ bootargs = "console=ttySC0,115200 ignore_loglevel root=/dev/nfs ip=dhcp rw";
};
memory {
device_type = "memory";
reg = <0x60000000 0x10000000>;
};
+
+ fixedregulator3v3: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ethernet@18300000 {
+ compatible = "smsc,lan9220", "smsc,lan9115";
+ reg = <0x18300000 0x1000>;
+
+ phy-mode = "mii";
+ interrupt-parent = <&irqpin>;
+ interrupts = <0 0>; /* IRQ0: hwirq 0 on irqpin */
+ reg-io-width = <4>;
+ vddvario-supply = <&fixedregulator3v3>;
+ vdd33a-supply = <&fixedregulator3v3>;
+ };
+};
+
+&irqpin {
+ status = "okay";
};
diff --git a/arch/arm/boot/dts/r8a7778.dtsi b/arch/arm/boot/dts/r8a7778.dtsi
index 3577aba..a6308a3 100644
--- a/arch/arm/boot/dts/r8a7778.dtsi
+++ b/arch/arm/boot/dts/r8a7778.dtsi
@@ -33,6 +33,25 @@
<0xfe430000 0x100>;
};
+ /* irqpin: IRQ0 - IRQ3 */
+ irqpin: irqpin@fe78001c {
+ compatible = "renesas,intc-irqpin";
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ status = "disabled"; /* default off */
+ reg = <0xfe78001c 4>,
+ <0xfe780010 4>,
+ <0xfe780024 4>,
+ <0xfe780044 4>,
+ <0xfe780064 4>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 27 0x4
+ 0 28 0x4
+ 0 29 0x4
+ 0 30 0x4>;
+ sense-bitfield-width = <2>;
+ };
+
gpio0: gpio@ffc40000 {
compatible = "renesas,gpio-r8a7778", "renesas,gpio-rcar";
reg = <0xffc40000 0x2c>;
diff --git a/arch/arm/boot/dts/r8a7779-marzen-reference.dts b/arch/arm/boot/dts/r8a7779-marzen-reference.dts
index 6d55083..ab4110a 100644
--- a/arch/arm/boot/dts/r8a7779-marzen-reference.dts
+++ b/arch/arm/boot/dts/r8a7779-marzen-reference.dts
@@ -42,8 +42,8 @@
pinctrl-names = "default";
phy-mode = "mii";
- interrupt-parent = <&gic>;
- interrupts = <0 28 0x4>;
+ interrupt-parent = <&irqpin0>;
+ interrupts = <1 0>; /* IRQ1: hwirq 1 on irqpin0 */
reg-io-width = <4>;
vddvario-supply = <&fixedregulator3v3>;
vdd33a-supply = <&fixedregulator3v3>;
@@ -63,6 +63,10 @@
};
};
+&irqpin0 {
+ status = "okay";
+};
+
&pfc {
pinctrl-0 = <&scif2_pins &scif4_pins &sdhi0_pins>;
pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/r8a7779.dtsi b/arch/arm/boot/dts/r8a7779.dtsi
index ebbe507..19faeac 100644
--- a/arch/arm/boot/dts/r8a7779.dtsi
+++ b/arch/arm/boot/dts/r8a7779.dtsi
@@ -135,6 +135,7 @@
irqpin0: irqpin@fe780010 {
compatible = "renesas,intc-irqpin";
#interrupt-cells = <2>;
+ status = "disabled";
interrupt-controller;
reg = <0xfe78001c 4>,
<0xfe780010 4>,
@@ -156,6 +157,7 @@
reg = <0xffc70000 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 79 0x4>;
+ status = "disabled";
};
i2c1: i2c@ffc71000 {
@@ -165,6 +167,7 @@
reg = <0xffc71000 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 82 0x4>;
+ status = "disabled";
};
i2c2: i2c@ffc72000 {
@@ -174,6 +177,7 @@
reg = <0xffc72000 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 80 0x4>;
+ status = "disabled";
};
i2c3: i2c@ffc73000 {
@@ -183,6 +187,7 @@
reg = <0xffc73000 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 81 0x4>;
+ status = "disabled";
};
pfc: pfc@fffc0000 {
diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index 413b4c2..ee845fa 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -24,6 +24,55 @@
reg = <0>;
clock-frequency = <1300000000>;
};
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <1>;
+ clock-frequency = <1300000000>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <2>;
+ clock-frequency = <1300000000>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <3>;
+ clock-frequency = <1300000000>;
+ };
+
+ cpu4: cpu@4 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0x100>;
+ clock-frequency = <780000000>;
+ };
+
+ cpu5: cpu@5 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0x101>;
+ clock-frequency = <780000000>;
+ };
+
+ cpu6: cpu@6 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0x102>;
+ clock-frequency = <780000000>;
+ };
+
+ cpu7: cpu@7 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0x103>;
+ clock-frequency = <780000000>;
+ };
};
gic: interrupt-controller@f1001000 {
@@ -127,6 +176,46 @@
interrupts = <0 0 4>, <0 1 4>, <0 2 4>, <0 3 4>;
};
+ i2c0: i2c@e6508000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "renesas,i2c-r8a7790";
+ reg = <0 0xe6508000 0 0x40>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 287 0x4>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@e6518000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "renesas,i2c-r8a7790";
+ reg = <0 0xe6518000 0 0x40>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 288 0x4>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@e6530000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "renesas,i2c-r8a7790";
+ reg = <0 0xe6530000 0 0x40>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 286 0x4>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@e6540000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "renesas,i2c-r8a7790";
+ reg = <0 0xe6540000 0 0x40>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 290 0x4>;
+ status = "disabled";
+ };
+
mmcif0: mmcif@ee200000 {
compatible = "renesas,sh-mmcif";
reg = <0 0xee200000 0 0x80>;
diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
new file mode 100644
index 0000000..fea5cfe
--- /dev/null
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -0,0 +1,74 @@
+/*
+ * Device Tree Source for the r8a7791 SoC
+ *
+ * Copyright (C) 2013 Renesas Electronics Corporation
+ * Copyright (C) 2013 Renesas Solutions Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/ {
+ compatible = "renesas,r8a7791";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <0>;
+ clock-frequency = <1300000000>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <1>;
+ clock-frequency = <1300000000>;
+ };
+ };
+
+ gic: interrupt-controller@f1001000 {
+ compatible = "arm,cortex-a15-gic";
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ interrupt-controller;
+ reg = <0 0xf1001000 0 0x1000>,
+ <0 0xf1002000 0 0x1000>,
+ <0 0xf1004000 0 0x2000>,
+ <0 0xf1006000 0 0x2000>;
+ interrupts = <1 9 0xf04>;
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <1 13 0xf08>,
+ <1 14 0xf08>,
+ <1 11 0xf08>,
+ <1 10 0xf08>;
+ };
+
+ irqc0: interrupt-controller@e61c0000 {
+ compatible = "renesas,irqc";
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ reg = <0 0xe61c0000 0 0x200>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 0 4>,
+ <0 1 4>,
+ <0 2 4>,
+ <0 3 4>,
+ <0 12 4>,
+ <0 13 4>,
+ <0 14 4>,
+ <0 15 4>,
+ <0 16 4>,
+ <0 17 4>;
+ };
+};
diff --git a/arch/arm/boot/dts/s3c6400.dtsi b/arch/arm/boot/dts/s3c6400.dtsi
new file mode 100644
index 0000000..a7d1c8e
--- /dev/null
+++ b/arch/arm/boot/dts/s3c6400.dtsi
@@ -0,0 +1,41 @@
+/*
+ * Samsung's S3C6400 SoC device tree source
+ *
+ * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
+ *
+ * Samsung's S3C6400 SoC device nodes are listed in this file. S3C6400
+ * based board files can include this file and provide values for board specfic
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * S3C6400 SoC. As device tree coverage for S3C6400 increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include "s3c64xx.dtsi"
+
+/ {
+ compatible = "samsung,s3c6400";
+};
+
+&vic0 {
+ valid-mask = <0xfffffe1f>;
+ valid-wakeup-mask = <0x00200004>;
+};
+
+&vic1 {
+ valid-mask = <0xffffffff>;
+ valid-wakeup-mask = <0x53020000>;
+};
+
+&soc {
+ clocks: clock-controller@7e00f000 {
+ compatible = "samsung,s3c6400-clock";
+ reg = <0x7e00f000 0x1000>;
+ #clock-cells = <1>;
+ };
+};
diff --git a/arch/arm/boot/dts/s3c6410-mini6410.dts b/arch/arm/boot/dts/s3c6410-mini6410.dts
new file mode 100644
index 0000000..57e00f9
--- /dev/null
+++ b/arch/arm/boot/dts/s3c6410-mini6410.dts
@@ -0,0 +1,228 @@
+/*
+ * Samsung's S3C6410 based Mini6410 board device tree source
+ *
+ * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
+ *
+ * Device tree source file for FriendlyARM Mini6410 board which is based on
+ * Samsung's S3C6410 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#include "s3c6410.dtsi"
+
+/ {
+ model = "FriendlyARM Mini6410 board based on S3C6410";
+ compatible = "friendlyarm,mini6410", "samsung,s3c6410";
+
+ memory {
+ reg = <0x50000000 0x10000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttySAC0,115200n8 earlyprintk rootwait root=/dev/mmcblk0p1";
+ };
+
+ clocks {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fin_pll: oscillator@0 {
+ compatible = "fixed-clock";
+ reg = <0>;
+ clock-frequency = <12000000>;
+ clock-output-names = "fin_pll";
+ #clock-cells = <0>;
+ };
+
+ xusbxti: oscillator@1 {
+ compatible = "fixed-clock";
+ reg = <1>;
+ clock-output-names = "xusbxti";
+ clock-frequency = <48000000>;
+ #clock-cells = <0>;
+ };
+ };
+
+ srom-cs1@18000000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x18000000 0x8000000>;
+ ranges;
+
+ ethernet@18000000 {
+ compatible = "davicom,dm9000";
+ reg = <0x18000000 0x2 0x18000004 0x2>;
+ interrupt-parent = <&gpn>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
+ davicom,no-eeprom;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys>;
+ autorepeat;
+
+ button-k1 {
+ label = "K1";
+ gpios = <&gpn 0 GPIO_ACTIVE_LOW>;
+ linux,code = <2>;
+ debounce-interval = <20>;
+ };
+
+ button-k2 {
+ label = "K2";
+ gpios = <&gpn 1 GPIO_ACTIVE_LOW>;
+ linux,code = <3>;
+ debounce-interval = <20>;
+ };
+
+ button-k3 {
+ label = "K3";
+ gpios = <&gpn 2 GPIO_ACTIVE_LOW>;
+ linux,code = <4>;
+ debounce-interval = <20>;
+ };
+
+ button-k4 {
+ label = "K4";
+ gpios = <&gpn 3 GPIO_ACTIVE_LOW>;
+ linux,code = <5>;
+ debounce-interval = <20>;
+ };
+
+ button-k5 {
+ label = "K5";
+ gpios = <&gpn 4 GPIO_ACTIVE_LOW>;
+ linux,code = <6>;
+ debounce-interval = <20>;
+ };
+
+ button-k6 {
+ label = "K6";
+ gpios = <&gpn 5 GPIO_ACTIVE_LOW>;
+ linux,code = <7>;
+ debounce-interval = <20>;
+ };
+
+ button-k7 {
+ label = "K7";
+ gpios = <&gpl 11 GPIO_ACTIVE_LOW>;
+ linux,code = <8>;
+ debounce-interval = <20>;
+ };
+
+ button-k8 {
+ label = "K8";
+ gpios = <&gpl 12 GPIO_ACTIVE_LOW>;
+ linux,code = <9>;
+ debounce-interval = <20>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_leds>;
+
+ led-1 {
+ label = "LED1";
+ gpios = <&gpk 4 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-2 {
+ label = "LED2";
+ gpios = <&gpk 5 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "mmc0";
+ };
+
+ led-3 {
+ label = "LED3";
+ gpios = <&gpk 6 GPIO_ACTIVE_LOW>;
+ };
+
+ led-4 {
+ label = "LED4";
+ gpios = <&gpk 7 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ buzzer {
+ compatible = "pwm-beeper";
+ pwms = <&pwm 0 1000000 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_out>;
+ };
+};
+
+&sdhci0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk>, <&sd0_cmd>, <&sd0_cd>, <&sd0_bus4>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_data>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_data>, <&uart1_fctl>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_data>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_data>;
+ status = "okay";
+};
+
+&pwm {
+ status = "okay";
+};
+
+&pinctrl0 {
+ gpio_leds: gpio-leds {
+ samsung,pins = "gpk-4", "gpk-5", "gpk-6", "gpk-7";
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ gpio_keys: gpio-keys {
+ samsung,pins = "gpn-0", "gpn-1", "gpn-2", "gpn-3",
+ "gpn-4", "gpn-5", "gpl-11", "gpl-12";
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_bus>;
+ status = "okay";
+
+ eeprom@50 {
+ compatible = "atmel,24c08";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+};
diff --git a/arch/arm/boot/dts/s3c6410-smdk6410.dts b/arch/arm/boot/dts/s3c6410-smdk6410.dts
new file mode 100644
index 0000000..ecf35ec
--- /dev/null
+++ b/arch/arm/boot/dts/s3c6410-smdk6410.dts
@@ -0,0 +1,103 @@
+/*
+ * Samsung S3C6410 based SMDK6410 board device tree source.
+ *
+ * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
+ *
+ * Device tree source file for SAMSUNG SMDK6410 board which is based on
+ * Samsung's S3C6410 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#include "s3c6410.dtsi"
+
+/ {
+ model = "SAMSUNG SMDK6410 board based on S3C6410";
+ compatible = "samsung,mini6410", "samsung,s3c6410";
+
+ memory {
+ reg = <0x50000000 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttySAC0,115200n8 earlyprintk rootwait root=/dev/mmcblk0p1";
+ };
+
+ clocks {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fin_pll: oscillator@0 {
+ compatible = "fixed-clock";
+ reg = <0>;
+ clock-frequency = <12000000>;
+ clock-output-names = "fin_pll";
+ #clock-cells = <0>;
+ };
+
+ xusbxti: oscillator@1 {
+ compatible = "fixed-clock";
+ reg = <1>;
+ clock-output-names = "xusbxti";
+ clock-frequency = <48000000>;
+ #clock-cells = <0>;
+ };
+ };
+
+ srom-cs1@18000000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x18000000 0x8000000>;
+ ranges;
+
+ ethernet@18000000 {
+ compatible = "smsc,lan9115";
+ reg = <0x18000000 0x10000>;
+ interrupt-parent = <&gpn>;
+ interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+ phy-mode = "mii";
+ reg-io-width = <4>;
+ smsc,force-internal-phy;
+ };
+ };
+};
+
+&sdhci0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk>, <&sd0_cmd>, <&sd0_cd>, <&sd0_bus4>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_data>, <&uart0_fctl>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_data>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_data>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_data>;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/s3c6410.dtsi b/arch/arm/boot/dts/s3c6410.dtsi
new file mode 100644
index 0000000..eb4226b
--- /dev/null
+++ b/arch/arm/boot/dts/s3c6410.dtsi
@@ -0,0 +1,57 @@
+/*
+ * Samsung's S3C6410 SoC device tree source
+ *
+ * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
+ *
+ * Samsung's S3C6410 SoC device nodes are listed in this file. S3C6410
+ * based board files can include this file and provide values for board specfic
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * S3C6410 SoC. As device tree coverage for S3C6410 increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include "s3c64xx.dtsi"
+
+/ {
+ compatible = "samsung,s3c6410";
+
+ aliases {
+ i2c1 = &i2c1;
+ };
+};
+
+&vic0 {
+ valid-mask = <0xffffff7f>;
+ valid-wakeup-mask = <0x00200004>;
+};
+
+&vic1 {
+ valid-mask = <0xffffffff>;
+ valid-wakeup-mask = <0x53020000>;
+};
+
+&soc {
+ clocks: clock-controller@7e00f000 {
+ compatible = "samsung,s3c6410-clock";
+ reg = <0x7e00f000 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ i2c1: i2c@7f00f000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x7f00f000 0x1000>;
+ interrupt-parent = <&vic0>;
+ interrupts = <5>;
+ clock-names = "i2c";
+ clocks = <&clocks PCLK_IIC1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
diff --git a/arch/arm/boot/dts/s3c64xx-pinctrl.dtsi b/arch/arm/boot/dts/s3c64xx-pinctrl.dtsi
new file mode 100644
index 0000000..b1197d8
--- /dev/null
+++ b/arch/arm/boot/dts/s3c64xx-pinctrl.dtsi
@@ -0,0 +1,687 @@
+/*
+ * Samsung's S3C64xx SoC series common device tree source
+ * - pin control-related definitions
+ *
+ * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
+ *
+ * Samsung's S3C64xx SoCs pin banks, pin-mux and pin-config options are
+ * listed as device tree nodes in this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#define PIN_PULL_NONE 0
+#define PIN_PULL_DOWN 1
+#define PIN_PULL_UP 2
+
+&pinctrl0 {
+ /*
+ * Pin banks
+ */
+
+ gpa: gpa {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpb: gpb {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpc: gpc {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpd: gpd {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpe: gpe {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpf: gpf {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpg: gpg {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gph: gph {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpi: gpi {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpj: gpj {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpk: gpk {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpl: gpl {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpm: gpm {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpn: gpn {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpo: gpo {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpp: gpp {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpq: gpq {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ /*
+ * Pin groups
+ */
+
+ uart0_data: uart0-data {
+ samsung,pins = "gpa-0", "gpa-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ uart0_fctl: uart0-fctl {
+ samsung,pins = "gpa-2", "gpa-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ uart1_data: uart1-data {
+ samsung,pins = "gpa-4", "gpa-5";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ uart1_fctl: uart1-fctl {
+ samsung,pins = "gpa-6", "gpa-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ uart2_data: uart2-data {
+ samsung,pins = "gpb-0", "gpb-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ uart3_data: uart3-data {
+ samsung,pins = "gpb-2", "gpb-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ ext_dma_0: ext-dma-0 {
+ samsung,pins = "gpb-0", "gpb-1";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ ext_dma_1: ext-dma-1 {
+ samsung,pins = "gpb-2", "gpb-3";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ irda_data_0: irda-data-0 {
+ samsung,pins = "gpb-0", "gpb-1";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ irda_data_1: irda-data-1 {
+ samsung,pins = "gpb-2", "gpb-3";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ irda_sdbw: irda-sdbw {
+ samsung,pins = "gpb-4";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ i2c0_bus: i2c0-bus {
+ samsung,pins = "gpb-5", "gpb-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_UP>;
+ };
+
+ i2c1_bus: i2c1-bus {
+ /* S3C6410-only */
+ samsung,pins = "gpb-2", "gpb-3";
+ samsung,pin-function = <6>;
+ samsung,pin-pud = <PIN_PULL_UP>;
+ };
+
+ spi0_bus: spi0-bus {
+ samsung,pins = "gpc-0", "gpc-1", "gpc-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_UP>;
+ };
+
+ spi0_cs: spi0-cs {
+ samsung,pins = "gpc-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ spi1_bus: spi1-bus {
+ samsung,pins = "gpc-4", "gpc-5", "gpc-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_UP>;
+ };
+
+ spi1_cs: spi1-cs {
+ samsung,pins = "gpc-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd0_cmd: sd0-cmd {
+ samsung,pins = "gpg-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd0_clk: sd0-clk {
+ samsung,pins = "gpg-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd0_bus1: sd0-bus1 {
+ samsung,pins = "gpg-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd0_bus4: sd0-bus4 {
+ samsung,pins = "gpg-2", "gpg-3", "gpg-4", "gpg-5";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd0_cd: sd0-cd {
+ samsung,pins = "gpg-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_UP>;
+ };
+
+ sd1_cmd: sd1-cmd {
+ samsung,pins = "gph-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd1_clk: sd1-clk {
+ samsung,pins = "gph-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd1_bus1: sd1-bus1 {
+ samsung,pins = "gph-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd1_bus4: sd1-bus4 {
+ samsung,pins = "gph-2", "gph-3", "gph-4", "gph-5";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd1_bus8: sd1-bus8 {
+ samsung,pins = "gph-2", "gph-3", "gph-4", "gph-5",
+ "gph-6", "gph-7", "gph-8", "gph-9";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd1_cd: sd1-cd {
+ samsung,pins = "gpg-6";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_UP>;
+ };
+
+ sd2_cmd: sd2-cmd {
+ samsung,pins = "gpc-4";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd2_clk: sd2-clk {
+ samsung,pins = "gpc-5";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd2_bus1: sd2-bus1 {
+ samsung,pins = "gph-6";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd2_bus4: sd2-bus4 {
+ samsung,pins = "gph-6", "gph-7", "gph-8", "gph-9";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ i2s0_bus: i2s0-bus {
+ samsung,pins = "gpd-0", "gpd-2", "gpd-3", "gpd-4";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ i2s0_cdclk: i2s0-cdclk {
+ samsung,pins = "gpd-1";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ i2s1_bus: i2s1-bus {
+ samsung,pins = "gpe-0", "gpe-2", "gpe-3", "gpe-4";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ i2s1_cdclk: i2s1-cdclk {
+ samsung,pins = "gpe-1";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ i2s2_bus: i2s2-bus {
+ /* S3C6410-only */
+ samsung,pins = "gpc-4", "gpc-5", "gpc-6", "gph-6",
+ "gph-8", "gph-9";
+ samsung,pin-function = <5>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ i2s2_cdclk: i2s2-cdclk {
+ /* S3C6410-only */
+ samsung,pins = "gph-7";
+ samsung,pin-function = <5>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ pcm0_bus: pcm0-bus {
+ samsung,pins = "gpd-0", "gpd-2", "gpd-3", "gpd-4";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ pcm0_extclk: pcm0-extclk {
+ samsung,pins = "gpd-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ pcm1_bus: pcm1-bus {
+ samsung,pins = "gpe-0", "gpe-2", "gpe-3", "gpe-4";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ pcm1_extclk: pcm1-extclk {
+ samsung,pins = "gpe-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ ac97_bus_0: ac97-bus-0 {
+ samsung,pins = "gpd-0", "gpd-1", "gpd-2", "gpd-3", "gpd-4";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ ac97_bus_1: ac97-bus-1 {
+ samsung,pins = "gpe-0", "gpe-1", "gpe-2", "gpe-3", "gpe-4";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ cam_port: cam-port {
+ samsung,pins = "gpf-0", "gpf-1", "gpf-2", "gpf-4",
+ "gpf-5", "gpf-6", "gpf-7", "gpf-8",
+ "gpf-9", "gpf-10", "gpf-11", "gpf-12";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ cam_rst: cam-rst {
+ samsung,pins = "gpf-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ cam_field: cam-field {
+ /* S3C6410-only */
+ samsung,pins = "gpb-4";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ pwm_extclk: pwm-extclk {
+ samsung,pins = "gpf-13";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ pwm0_out: pwm0-out {
+ samsung,pins = "gpf-14";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ pwm1_out: pwm1-out {
+ samsung,pins = "gpf-15";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ clkout0: clkout-0 {
+ samsung,pins = "gpf-14";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col0_0: keypad-col0-0 {
+ samsung,pins = "gph-0";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col1_0: keypad-col1-0 {
+ samsung,pins = "gph-1";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col2_0: keypad-col2-0 {
+ samsung,pins = "gph-2";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col3_0: keypad-col3-0 {
+ samsung,pins = "gph-3";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col4_0: keypad-col4-0 {
+ samsung,pins = "gph-4";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col5_0: keypad-col5-0 {
+ samsung,pins = "gph-5";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col6_0: keypad-col6-0 {
+ samsung,pins = "gph-6";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col7_0: keypad-col7-0 {
+ samsung,pins = "gph-7";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col0_1: keypad-col0-1 {
+ samsung,pins = "gpl-0";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col1_1: keypad-col1-1 {
+ samsung,pins = "gpl-1";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col2_1: keypad-col2-1 {
+ samsung,pins = "gpl-2";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col3_1: keypad-col3-1 {
+ samsung,pins = "gpl-3";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col4_1: keypad-col4-1 {
+ samsung,pins = "gpl-4";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col5_1: keypad-col5-1 {
+ samsung,pins = "gpl-5";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col6_1: keypad-col6-1 {
+ samsung,pins = "gpl-6";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col7_1: keypad-col7-1 {
+ samsung,pins = "gpl-7";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row0_0: keypad-row0-0 {
+ samsung,pins = "gpk-8";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row1_0: keypad-row1-0 {
+ samsung,pins = "gpk-9";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row2_0: keypad-row2-0 {
+ samsung,pins = "gpk-10";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row3_0: keypad-row3-0 {
+ samsung,pins = "gpk-11";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row4_0: keypad-row4-0 {
+ samsung,pins = "gpk-12";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row5_0: keypad-row5-0 {
+ samsung,pins = "gpk-13";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row6_0: keypad-row6-0 {
+ samsung,pins = "gpk-14";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row7_0: keypad-row7-0 {
+ samsung,pins = "gpk-15";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row0_1: keypad-row0-1 {
+ samsung,pins = "gpn-0";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row1_1: keypad-row1-1 {
+ samsung,pins = "gpn-1";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row2_1: keypad-row2-1 {
+ samsung,pins = "gpn-2";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row3_1: keypad-row3-1 {
+ samsung,pins = "gpn-3";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row4_1: keypad-row4-1 {
+ samsung,pins = "gpn-4";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row5_1: keypad-row5-1 {
+ samsung,pins = "gpn-5";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row6_1: keypad-row6-1 {
+ samsung,pins = "gpn-6";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row7_1: keypad-row7-1 {
+ samsung,pins = "gpn-7";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ lcd_ctrl: lcd-ctrl {
+ samsung,pins = "gpj-8", "gpj-9", "gpj-10", "gpj-11";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ lcd_data16: lcd-data-width16 {
+ samsung,pins = "gpi-3", "gpi-4", "gpi-5", "gpi-6",
+ "gpi-7", "gpi-10", "gpi-11", "gpi-12",
+ "gpi-13", "gpi-14", "gpi-15", "gpj-3",
+ "gpj-4", "gpj-5", "gpj-6", "gpj-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ lcd_data18: lcd-data-width18 {
+ samsung,pins = "gpi-2", "gpi-3", "gpi-4", "gpi-5",
+ "gpi-6", "gpi-7", "gpi-10", "gpi-11",
+ "gpi-12", "gpi-13", "gpi-14", "gpi-15",
+ "gpj-2", "gpj-3", "gpj-4", "gpj-5",
+ "gpj-6", "gpj-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ lcd_data24: lcd-data-width24 {
+ samsung,pins = "gpi-0", "gpi-1", "gpi-2", "gpi-3",
+ "gpi-4", "gpi-5", "gpi-6", "gpi-7",
+ "gpi-8", "gpi-9", "gpi-10", "gpi-11",
+ "gpi-12", "gpi-13", "gpi-14", "gpi-15",
+ "gpj-0", "gpj-1", "gpj-2", "gpj-3",
+ "gpj-4", "gpj-5", "gpj-6", "gpj-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ hsi_bus: hsi-bus {
+ samsung,pins = "gpk-0", "gpk-1", "gpk-2", "gpk-3",
+ "gpk-4", "gpk-5", "gpk-6", "gpk-7";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+};
diff --git a/arch/arm/boot/dts/s3c64xx.dtsi b/arch/arm/boot/dts/s3c64xx.dtsi
new file mode 100644
index 0000000..4e3be4d
--- /dev/null
+++ b/arch/arm/boot/dts/s3c64xx.dtsi
@@ -0,0 +1,199 @@
+/*
+ * Samsung's S3C64xx SoC series common device tree source
+ *
+ * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
+ *
+ * Samsung's S3C64xx SoC series device nodes are listed in this file.
+ * Particular SoCs from S3C64xx series can include this file and provide
+ * values for SoCs specfic bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * S3C64xx SoCs. As device tree coverage for S3C64xx increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "skeleton.dtsi"
+#include <dt-bindings/clock/samsung,s3c64xx-clock.h>
+
+/ {
+ aliases {
+ i2c0 = &i2c0;
+ pinctrl0 = &pinctrl0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,arm1176jzf-s", "arm,arm1176";
+ reg = <0x0>;
+ };
+ };
+
+ soc: soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ vic0: interrupt-controller@71200000 {
+ compatible = "arm,pl192-vic";
+ interrupt-controller;
+ reg = <0x71200000 0x1000>;
+ #interrupt-cells = <1>;
+ };
+
+ vic1: interrupt-controller@71300000 {
+ compatible = "arm,pl192-vic";
+ interrupt-controller;
+ reg = <0x71300000 0x1000>;
+ #interrupt-cells = <1>;
+ };
+
+ sdhci0: sdhci@7c200000 {
+ compatible = "samsung,s3c6410-sdhci";
+ reg = <0x7c200000 0x100>;
+ interrupt-parent = <&vic1>;
+ interrupts = <24>;
+ clock-names = "hsmmc", "mmc_busclk.0", "mmc_busclk.2";
+ clocks = <&clocks HCLK_HSMMC0>, <&clocks HCLK_HSMMC0>,
+ <&clocks SCLK_MMC0>;
+ status = "disabled";
+ };
+
+ sdhci1: sdhci@7c300000 {
+ compatible = "samsung,s3c6410-sdhci";
+ reg = <0x7c300000 0x100>;
+ interrupt-parent = <&vic1>;
+ interrupts = <25>;
+ clock-names = "hsmmc", "mmc_busclk.0", "mmc_busclk.2";
+ clocks = <&clocks HCLK_HSMMC1>, <&clocks HCLK_HSMMC1>,
+ <&clocks SCLK_MMC1>;
+ status = "disabled";
+ };
+
+ sdhci2: sdhci@7c400000 {
+ compatible = "samsung,s3c6410-sdhci";
+ reg = <0x7c400000 0x100>;
+ interrupt-parent = <&vic1>;
+ interrupts = <17>;
+ clock-names = "hsmmc", "mmc_busclk.0", "mmc_busclk.2";
+ clocks = <&clocks HCLK_HSMMC2>, <&clocks HCLK_HSMMC2>,
+ <&clocks SCLK_MMC2>;
+ status = "disabled";
+ };
+
+ watchdog: watchdog@7e004000 {
+ compatible = "samsung,s3c2410-wdt";
+ reg = <0x7e004000 0x1000>;
+ interrupt-parent = <&vic0>;
+ interrupts = <26>;
+ clock-names = "watchdog";
+ clocks = <&clocks PCLK_WDT>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@7f004000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x7f004000 0x1000>;
+ interrupt-parent = <&vic1>;
+ interrupts = <18>;
+ clock-names = "i2c";
+ clocks = <&clocks PCLK_IIC0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ uart0: serial@7f005000 {
+ compatible = "samsung,s3c6400-uart";
+ reg = <0x7f005000 0x100>;
+ interrupt-parent = <&vic1>;
+ interrupts = <5>;
+ clock-names = "uart", "clk_uart_baud2",
+ "clk_uart_baud3";
+ clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>,
+ <&clocks SCLK_UART>;
+ status = "disabled";
+ };
+
+ uart1: serial@7f005400 {
+ compatible = "samsung,s3c6400-uart";
+ reg = <0x7f005400 0x100>;
+ interrupt-parent = <&vic1>;
+ interrupts = <6>;
+ clock-names = "uart", "clk_uart_baud2",
+ "clk_uart_baud3";
+ clocks = <&clocks PCLK_UART1>, <&clocks PCLK_UART1>,
+ <&clocks SCLK_UART>;
+ status = "disabled";
+ };
+
+ uart2: serial@7f005800 {
+ compatible = "samsung,s3c6400-uart";
+ reg = <0x7f005800 0x100>;
+ interrupt-parent = <&vic1>;
+ interrupts = <7>;
+ clock-names = "uart", "clk_uart_baud2",
+ "clk_uart_baud3";
+ clocks = <&clocks PCLK_UART2>, <&clocks PCLK_UART2>,
+ <&clocks SCLK_UART>;
+ status = "disabled";
+ };
+
+ uart3: serial@7f005c00 {
+ compatible = "samsung,s3c6400-uart";
+ reg = <0x7f005c00 0x100>;
+ interrupt-parent = <&vic1>;
+ interrupts = <8>;
+ clock-names = "uart", "clk_uart_baud2",
+ "clk_uart_baud3";
+ clocks = <&clocks PCLK_UART3>, <&clocks PCLK_UART3>,
+ <&clocks SCLK_UART>;
+ status = "disabled";
+ };
+
+ pwm: pwm@7f006000 {
+ compatible = "samsung,s3c6400-pwm";
+ reg = <0x7f006000 0x1000>;
+ interrupt-parent = <&vic0>;
+ interrupts = <23>, <24>, <25>, <27>, <28>;
+ clock-names = "timers";
+ clocks = <&clocks PCLK_PWM>;
+ samsung,pwm-outputs = <0>, <1>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pinctrl0: pinctrl@7f008000 {
+ compatible = "samsung,s3c64xx-pinctrl";
+ reg = <0x7f008000 0x1000>;
+ interrupt-parent = <&vic1>;
+ interrupts = <21>;
+
+ pctrl_int_map: pinctrl-interrupt-map {
+ interrupt-map = <0 &vic0 0>,
+ <1 &vic0 1>,
+ <2 &vic1 0>,
+ <3 &vic1 1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <1>;
+ };
+
+ wakeup-interrupt-controller {
+ compatible = "samsung,s3c64xx-wakeup-eint";
+ interrupts = <0>, <1>, <2>, <3>;
+ interrupt-parent = <&pctrl_int_map>;
+ };
+ };
+ };
+};
+
+#include "s3c64xx-pinctrl.dtsi"
diff --git a/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts b/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts
index 2122306..8ee06dd 100644
--- a/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts
+++ b/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts
@@ -108,6 +108,7 @@
};
&i2c0 {
+ status = "okay";
as3711@40 {
compatible = "ams,as3711";
reg = <0x40>;
@@ -183,6 +184,7 @@
&i2c3 {
pinctrl-0 = <&i2c3_pins>;
pinctrl-names = "default";
+ status = "okay";
};
&mmcif {
diff --git a/arch/arm/boot/dts/sh73a0.dtsi b/arch/arm/boot/dts/sh73a0.dtsi
index 3955c76..fcf2688 100644
--- a/arch/arm/boot/dts/sh73a0.dtsi
+++ b/arch/arm/boot/dts/sh73a0.dtsi
@@ -135,6 +135,7 @@
0 168 0x4
0 169 0x4
0 170 0x4>;
+ status = "disabled";
};
i2c1: i2c@e6822000 {
@@ -147,6 +148,7 @@
0 52 0x4
0 53 0x4
0 54 0x4>;
+ status = "disabled";
};
i2c2: i2c@e6824000 {
@@ -159,6 +161,7 @@
0 172 0x4
0 173 0x4
0 174 0x4>;
+ status = "disabled";
};
i2c3: i2c@e6826000 {
@@ -171,6 +174,7 @@
0 184 0x4
0 185 0x4
0 186 0x4>;
+ status = "disabled";
};
i2c4: i2c@e6828000 {
@@ -183,6 +187,7 @@
0 188 0x4
0 189 0x4
0 190 0x4>;
+ status = "disabled";
};
mmcif: mmcif@e6bd0000 {
diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi
index e273fa9..6d09b8d 100644
--- a/arch/arm/boot/dts/socfpga.dtsi
+++ b/arch/arm/boot/dts/socfpga.dtsi
@@ -147,7 +147,7 @@
reg = <0x58>;
};
- cfg_s2f_usr0_clk: cfg_s2f_usr0_clk {
+ cfg_h2f_usr0_clk: cfg_h2f_usr0_clk {
#clock-cells = <0>;
compatible = "altr,socfpga-perip-clk";
clocks = <&main_pll>;
@@ -198,7 +198,7 @@
reg = <0x98>;
};
- s2f_usr1_clk: s2f_usr1_clk {
+ h2f_usr1_clk: h2f_usr1_clk {
#clock-cells = <0>;
compatible = "altr,socfpga-perip-clk";
clocks = <&periph_pll>;
@@ -235,7 +235,7 @@
reg = <0xD0>;
};
- s2f_usr2_clk: s2f_usr2_clk {
+ h2f_usr2_clk: h2f_usr2_clk {
#clock-cells = <0>;
compatible = "altr,socfpga-perip-clk";
clocks = <&sdram_pll>;
@@ -243,197 +243,197 @@
};
};
- mpu_periph_clk: mpu_periph_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&mpuclk>;
- fixed-divider = <4>;
+ mpu_periph_clk: mpu_periph_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&mpuclk>;
+ fixed-divider = <4>;
};
- mpu_l2_ram_clk: mpu_l2_ram_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&mpuclk>;
- fixed-divider = <2>;
+ mpu_l2_ram_clk: mpu_l2_ram_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&mpuclk>;
+ fixed-divider = <2>;
};
- l4_main_clk: l4_main_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&mainclk>;
- clk-gate = <0x60 0>;
+ l4_main_clk: l4_main_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&mainclk>;
+ clk-gate = <0x60 0>;
};
- l3_main_clk: l3_main_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&mainclk>;
+ l3_main_clk: l3_main_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&mainclk>;
};
- l3_mp_clk: l3_mp_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&mainclk>;
- div-reg = <0x64 0 2>;
- clk-gate = <0x60 1>;
+ l3_mp_clk: l3_mp_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&mainclk>;
+ div-reg = <0x64 0 2>;
+ clk-gate = <0x60 1>;
};
- l3_sp_clk: l3_sp_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&mainclk>;
- div-reg = <0x64 2 2>;
- };
-
- l4_mp_clk: l4_mp_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&mainclk>, <&per_base_clk>;
- div-reg = <0x64 4 3>;
- clk-gate = <0x60 2>;
+ l3_sp_clk: l3_sp_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&mainclk>;
+ div-reg = <0x64 2 2>;
};
- l4_sp_clk: l4_sp_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&mainclk>, <&per_base_clk>;
- div-reg = <0x64 7 3>;
- clk-gate = <0x60 3>;
+ l4_mp_clk: l4_mp_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&mainclk>, <&per_base_clk>;
+ div-reg = <0x64 4 3>;
+ clk-gate = <0x60 2>;
};
- dbg_at_clk: dbg_at_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&dbg_base_clk>;
- div-reg = <0x68 0 2>;
- clk-gate = <0x60 4>;
+ l4_sp_clk: l4_sp_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&mainclk>, <&per_base_clk>;
+ div-reg = <0x64 7 3>;
+ clk-gate = <0x60 3>;
};
- dbg_clk: dbg_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&dbg_base_clk>;
- div-reg = <0x68 2 2>;
- clk-gate = <0x60 5>;
+ dbg_at_clk: dbg_at_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&dbg_base_clk>;
+ div-reg = <0x68 0 2>;
+ clk-gate = <0x60 4>;
};
- dbg_trace_clk: dbg_trace_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&dbg_base_clk>;
- div-reg = <0x6C 0 3>;
- clk-gate = <0x60 6>;
+ dbg_clk: dbg_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&dbg_base_clk>;
+ div-reg = <0x68 2 2>;
+ clk-gate = <0x60 5>;
};
- dbg_timer_clk: dbg_timer_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&dbg_base_clk>;
- clk-gate = <0x60 7>;
+ dbg_trace_clk: dbg_trace_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&dbg_base_clk>;
+ div-reg = <0x6C 0 3>;
+ clk-gate = <0x60 6>;
};
- cfg_clk: cfg_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&cfg_s2f_usr0_clk>;
- clk-gate = <0x60 8>;
+ dbg_timer_clk: dbg_timer_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&dbg_base_clk>;
+ clk-gate = <0x60 7>;
};
- s2f_user0_clk: s2f_user0_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&cfg_s2f_usr0_clk>;
- clk-gate = <0x60 9>;
+ cfg_clk: cfg_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&cfg_h2f_usr0_clk>;
+ clk-gate = <0x60 8>;
};
- emac_0_clk: emac_0_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&emac0_clk>;
- clk-gate = <0xa0 0>;
+ h2f_user0_clk: h2f_user0_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&cfg_h2f_usr0_clk>;
+ clk-gate = <0x60 9>;
};
- emac_1_clk: emac_1_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&emac1_clk>;
- clk-gate = <0xa0 1>;
+ emac_0_clk: emac_0_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&emac0_clk>;
+ clk-gate = <0xa0 0>;
};
- usb_mp_clk: usb_mp_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&per_base_clk>;
- clk-gate = <0xa0 2>;
- div-reg = <0xa4 0 3>;
+ emac_1_clk: emac_1_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&emac1_clk>;
+ clk-gate = <0xa0 1>;
};
- spi_m_clk: spi_m_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&per_base_clk>;
- clk-gate = <0xa0 3>;
- div-reg = <0xa4 3 3>;
+ usb_mp_clk: usb_mp_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&per_base_clk>;
+ clk-gate = <0xa0 2>;
+ div-reg = <0xa4 0 3>;
};
- can0_clk: can0_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&per_base_clk>;
- clk-gate = <0xa0 4>;
- div-reg = <0xa4 6 3>;
+ spi_m_clk: spi_m_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&per_base_clk>;
+ clk-gate = <0xa0 3>;
+ div-reg = <0xa4 3 3>;
};
- can1_clk: can1_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&per_base_clk>;
- clk-gate = <0xa0 5>;
- div-reg = <0xa4 9 3>;
+ can0_clk: can0_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&per_base_clk>;
+ clk-gate = <0xa0 4>;
+ div-reg = <0xa4 6 3>;
};
- gpio_db_clk: gpio_db_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&per_base_clk>;
- clk-gate = <0xa0 6>;
- div-reg = <0xa8 0 24>;
+ can1_clk: can1_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&per_base_clk>;
+ clk-gate = <0xa0 5>;
+ div-reg = <0xa4 9 3>;
};
- s2f_user1_clk: s2f_user1_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&s2f_usr1_clk>;
- clk-gate = <0xa0 7>;
+ gpio_db_clk: gpio_db_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&per_base_clk>;
+ clk-gate = <0xa0 6>;
+ div-reg = <0xa8 0 24>;
};
- sdmmc_clk: sdmmc_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&f2s_periph_ref_clk>, <&main_nand_sdmmc_clk>, <&per_nand_mmc_clk>;
- clk-gate = <0xa0 8>;
+ h2f_user1_clk: h2f_user1_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&h2f_usr1_clk>;
+ clk-gate = <0xa0 7>;
};
- nand_x_clk: nand_x_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&f2s_periph_ref_clk>, <&main_nand_sdmmc_clk>, <&per_nand_mmc_clk>;
- clk-gate = <0xa0 9>;
+ sdmmc_clk: sdmmc_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&f2s_periph_ref_clk>, <&main_nand_sdmmc_clk>, <&per_nand_mmc_clk>;
+ clk-gate = <0xa0 8>;
};
- nand_clk: nand_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&f2s_periph_ref_clk>, <&main_nand_sdmmc_clk>, <&per_nand_mmc_clk>;
- clk-gate = <0xa0 10>;
- fixed-divider = <4>;
+ nand_x_clk: nand_x_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&f2s_periph_ref_clk>, <&main_nand_sdmmc_clk>, <&per_nand_mmc_clk>;
+ clk-gate = <0xa0 9>;
};
- qspi_clk: qspi_clk {
- #clock-cells = <0>;
- compatible = "altr,socfpga-gate-clk";
- clocks = <&f2s_periph_ref_clk>, <&main_qspi_clk>, <&per_qspi_clk>;
- clk-gate = <0xa0 11>;
+ nand_clk: nand_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&f2s_periph_ref_clk>, <&main_nand_sdmmc_clk>, <&per_nand_mmc_clk>;
+ clk-gate = <0xa0 10>;
+ fixed-divider = <4>;
+ };
+
+ qspi_clk: qspi_clk {
+ #clock-cells = <0>;
+ compatible = "altr,socfpga-gate-clk";
+ clocks = <&f2s_periph_ref_clk>, <&main_qspi_clk>, <&per_qspi_clk>;
+ clk-gate = <0xa0 11>;
};
};
};
@@ -473,6 +473,7 @@
compatible = "arm,cortex-a9-twd-timer";
reg = <0xfffec600 0x100>;
interrupts = <1 13 0xf04>;
+ clocks = <&mpu_periph_clk>;
};
timer0: timer0@ffc08000 {
@@ -516,9 +517,9 @@
};
rstmgr@ffd05000 {
- compatible = "altr,rst-mgr";
- reg = <0xffd05000 0x1000>;
- };
+ compatible = "altr,rst-mgr";
+ reg = <0xffd05000 0x1000>;
+ };
sysmgr@ffd08000 {
compatible = "altr,sys-mgr";
diff --git a/arch/arm/boot/dts/socfpga_arria5.dtsi b/arch/arm/boot/dts/socfpga_arria5.dtsi
new file mode 100644
index 0000000..a85b404
--- /dev/null
+++ b/arch/arm/boot/dts/socfpga_arria5.dtsi
@@ -0,0 +1,58 @@
+/*
+ * Copyright (C) 2013 Altera Corporation <www.altera.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/dts-v1/;
+/include/ "socfpga.dtsi"
+
+/ {
+ soc {
+ clkmgr@ffd04000 {
+ clocks {
+ osc1 {
+ clock-frequency = <25000000>;
+ };
+ };
+ };
+
+ serial0@ffc02000 {
+ clock-frequency = <100000000>;
+ };
+
+ serial1@ffc03000 {
+ clock-frequency = <100000000>;
+ };
+
+ sysmgr@ffd08000 {
+ cpu1-start-addr = <0xffd080c4>;
+ };
+
+ timer0@ffc08000 {
+ clock-frequency = <100000000>;
+ };
+
+ timer1@ffc09000 {
+ clock-frequency = <100000000>;
+ };
+
+ timer2@ffd00000 {
+ clock-frequency = <25000000>;
+ };
+
+ timer3@ffd01000 {
+ clock-frequency = <25000000>;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/socfpga_arria5_socdk.dts b/arch/arm/boot/dts/socfpga_arria5_socdk.dts
new file mode 100644
index 0000000..5beffb2
--- /dev/null
+++ b/arch/arm/boot/dts/socfpga_arria5_socdk.dts
@@ -0,0 +1,40 @@
+/*
+ * Copyright (C) 2013 Altera Corporation <www.altera.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/include/ "socfpga_arria5.dtsi"
+
+/ {
+ model = "Altera SOCFPGA Arria V SoC Development Kit";
+ compatible = "altr,socfpga-arria5", "altr,socfpga";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ memory {
+ name = "memory";
+ device_type = "memory";
+ reg = <0x0 0x40000000>; /* 1GB */
+ };
+
+ aliases {
+ /* this allow the ethaddr uboot environmnet variable contents
+ * to be added to the gmac1 device tree blob.
+ */
+ ethernet0 = &gmac1;
+ };
+};
diff --git a/arch/arm/boot/dts/socfpga_cyclone5.dts b/arch/arm/boot/dts/socfpga_cyclone5.dtsi
similarity index 77%
rename from arch/arm/boot/dts/socfpga_cyclone5.dts
rename to arch/arm/boot/dts/socfpga_cyclone5.dtsi
index 973999d..a8716f6 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5.dts
+++ b/arch/arm/boot/dts/socfpga_cyclone5.dtsi
@@ -19,26 +19,6 @@
/include/ "socfpga.dtsi"
/ {
- model = "Altera SOCFPGA Cyclone V";
- compatible = "altr,socfpga-cyclone5", "altr,socfpga";
-
- chosen {
- bootargs = "console=ttyS0,57600";
- };
-
- memory {
- name = "memory";
- device_type = "memory";
- reg = <0x0 0x40000000>; /* 1GB */
- };
-
- aliases {
- /* this allow the ethaddr uboot environmnet variable contents
- * to be added to the gmac1 device tree blob.
- */
- ethernet0 = &gmac1;
- };
-
soc {
clkmgr@ffd04000 {
clocks {
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts b/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts
new file mode 100644
index 0000000..2ee52ab
--- /dev/null
+++ b/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts
@@ -0,0 +1,40 @@
+/*
+ * Copyright (C) 2012 Altera Corporation <www.altera.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/include/ "socfpga_cyclone5.dtsi"
+
+/ {
+ model = "Altera SOCFPGA Cyclone V SoC Development Kit";
+ compatible = "altr,socfpga-cyclone5", "altr,socfpga";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ memory {
+ name = "memory";
+ device_type = "memory";
+ reg = <0x0 0x40000000>; /* 1GB */
+ };
+
+ aliases {
+ /* this allow the ethaddr uboot environmnet variable contents
+ * to be added to the gmac1 device tree blob.
+ */
+ ethernet0 = &gmac1;
+ };
+};
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts b/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts
new file mode 100644
index 0000000..50b99a2
--- /dev/null
+++ b/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts
@@ -0,0 +1,37 @@
+/*
+ * Copyright (C) 2013 Steffen Trumtrar <s.trumtrar@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/include/ "socfpga_cyclone5.dtsi"
+
+/ {
+ model = "Terasic SoCkit";
+ compatible = "altr,socfpga-cyclone5", "altr,socfpga";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ memory {
+ name = "memory";
+ device_type = "memory";
+ reg = <0x0 0x40000000>; /* 1GB */
+ };
+};
+
+&gmac1 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/ste-dbx5x0.dtsi
index 1c1091e..7da99fe 100644
--- a/arch/arm/boot/dts/ste-dbx5x0.dtsi
+++ b/arch/arm/boot/dts/ste-dbx5x0.dtsi
@@ -10,6 +10,7 @@
*/
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/mfd/dbx500-prcmu.h>
#include "skeleton.dtsi"
/ {
@@ -42,16 +43,56 @@
interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>;
};
+
+ clocks {
+ compatible = "stericsson,u8500-clks";
+
+ prcmu_clk: prcmu-clock {
+ #clock-cells = <1>;
+ };
+
+ prcc_pclk: prcc-periph-clock {
+ #clock-cells = <2>;
+ };
+
+ prcc_kclk: prcc-kernel-clock {
+ #clock-cells = <2>;
+ };
+
+ rtc_clk: rtc32k-clock {
+ #clock-cells = <0>;
+ };
+
+ smp_twd_clk: smp-twd-clock {
+ #clock-cells = <0>;
+ };
+ };
+
+ mtu@a03c6000 {
+ /* Nomadik System Timer */
+ compatible = "st,nomadik-mtu";
+ reg = <0xa03c6000 0x1000>;
+ interrupts = <0 4 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&prcmu_clk PRCMU_TIMCLK>, <&prcc_pclk 6 6>;
+ clock-names = "timclk", "apb_pclk";
+ };
+
timer@a0410600 {
compatible = "arm,cortex-a9-twd-timer";
reg = <0xa0410600 0x20>;
interrupts = <1 13 0x304>; /* IRQ level high per-CPU */
+
+ clocks = <&smp_twd_clk>;
};
rtc@80154000 {
compatible = "arm,rtc-pl031", "arm,primecell";
reg = <0x80154000 0x1000>;
interrupts = <0 18 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&rtc_clk>;
+ clock-names = "apb_pclk";
};
gpio0: gpio@8012e000 {
@@ -65,6 +106,8 @@
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <0>;
+
+ clocks = <&prcc_pclk 1 9>;
};
gpio1: gpio@8012e080 {
@@ -78,6 +121,8 @@
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <1>;
+
+ clocks = <&prcc_pclk 1 9>;
};
gpio2: gpio@8000e000 {
@@ -91,6 +136,8 @@
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <2>;
+
+ clocks = <&prcc_pclk 3 8>;
};
gpio3: gpio@8000e080 {
@@ -104,6 +151,8 @@
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <3>;
+
+ clocks = <&prcc_pclk 3 8>;
};
gpio4: gpio@8000e100 {
@@ -117,6 +166,8 @@
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <4>;
+
+ clocks = <&prcc_pclk 3 8>;
};
gpio5: gpio@8000e180 {
@@ -130,6 +181,8 @@
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <5>;
+
+ clocks = <&prcc_pclk 3 8>;
};
gpio6: gpio@8011e000 {
@@ -143,6 +196,8 @@
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <6>;
+
+ clocks = <&prcc_pclk 2 11>;
};
gpio7: gpio@8011e080 {
@@ -156,6 +211,8 @@
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <7>;
+
+ clocks = <&prcc_pclk 2 11>;
};
gpio8: gpio@a03fe000 {
@@ -169,6 +226,8 @@
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <8>;
+
+ clocks = <&prcc_pclk 5 1>;
};
pinctrl {
@@ -177,8 +236,7 @@
};
usb_per5@a03e0000 {
- compatible = "stericsson,db8500-musb",
- "mentor,musb";
+ compatible = "stericsson,db8500-musb";
reg = <0xa03e0000 0x10000>;
interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "mc";
@@ -210,6 +268,8 @@
"iep_6_14", "oep_6_14",
"iep_7_15", "oep_7_15",
"iep_8", "oep_8";
+
+ clocks = <&prcc_pclk 5 0>;
};
dma: dma-controller@801C0000 {
@@ -220,6 +280,8 @@
#dma-cells = <3>;
memcpy-channels = <56 57 58 59 60>;
+
+ clocks = <&prcmu_clk PRCMU_DMACLK>;
};
prcmu: prcmu@80157000 {
@@ -238,6 +300,13 @@
reg = <0x80157450 0xC>;
};
+ cpufreq {
+ compatible = "stericsson,cpufreq-ux500";
+ clocks = <&prcmu_clk PRCMU_ARMSS>;
+ clock-names = "armss";
+ status = "disabled";
+ };
+
thermal@801573c0 {
compatible = "stericsson,db8500-thermal";
reg = <0x801573c0 0x40>;
@@ -559,65 +628,74 @@
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x80004000 0x1000>;
interrupts = <0 21 IRQ_TYPE_LEVEL_HIGH>;
- arm,primecell-periphid = <0x180024>;
#address-cells = <1>;
#size-cells = <0>;
v-i2c-supply = <&db8500_vape_reg>;
clock-frequency = <400000>;
+ clocks = <&prcc_kclk 3 3>, <&prcc_pclk 3 3>;
+ clock-names = "i2cclk", "apb_pclk";
};
i2c@80122000 {
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x80122000 0x1000>;
interrupts = <0 22 IRQ_TYPE_LEVEL_HIGH>;
- arm,primecell-periphid = <0x180024>;
#address-cells = <1>;
#size-cells = <0>;
v-i2c-supply = <&db8500_vape_reg>;
clock-frequency = <400000>;
+
+ clocks = <&prcc_kclk 1 2>, <&prcc_pclk 1 2>;
+ clock-names = "i2cclk", "apb_pclk";
};
i2c@80128000 {
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x80128000 0x1000>;
interrupts = <0 55 IRQ_TYPE_LEVEL_HIGH>;
- arm,primecell-periphid = <0x180024>;
#address-cells = <1>;
#size-cells = <0>;
v-i2c-supply = <&db8500_vape_reg>;
clock-frequency = <400000>;
+
+ clocks = <&prcc_kclk 1 6>, <&prcc_pclk 1 6>;
+ clock-names = "i2cclk", "apb_pclk";
};
i2c@80110000 {
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x80110000 0x1000>;
interrupts = <0 12 IRQ_TYPE_LEVEL_HIGH>;
- arm,primecell-periphid = <0x180024>;
#address-cells = <1>;
#size-cells = <0>;
v-i2c-supply = <&db8500_vape_reg>;
clock-frequency = <400000>;
+
+ clocks = <&prcc_kclk 2 0>, <&prcc_pclk 2 0>;
+ clock-names = "i2cclk", "apb_pclk";
};
i2c@8012a000 {
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x8012a000 0x1000>;
interrupts = <0 51 IRQ_TYPE_LEVEL_HIGH>;
- arm,primecell-periphid = <0x180024>;
#address-cells = <1>;
#size-cells = <0>;
v-i2c-supply = <&db8500_vape_reg>;
clock-frequency = <400000>;
+
+ clocks = <&prcc_kclk 1 9>, <&prcc_pclk 1 10>;
+ clock-names = "i2cclk", "apb_pclk";
};
ssp@80002000 {
@@ -626,7 +704,80 @@
interrupts = <0 14 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
- status = "disabled";
+ clocks = <&prcc_kclk 3 1>, <&prcc_pclk 3 1>;
+ clock-names = "ssp0clk", "apb_pclk";
+ dmas = <&dma 8 0 0x2>, /* Logical - DevToMem */
+ <&dma 8 0 0x0>; /* Logical - MemToDev */
+ dma-names = "rx", "tx";
+ };
+
+ ssp@80003000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x80003000 0x1000>;
+ interrupts = <0 52 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&prcc_kclk 3 2>, <&prcc_pclk 3 2>;
+ clock-names = "ssp1clk", "apb_pclk";
+ dmas = <&dma 9 0 0x2>, /* Logical - DevToMem */
+ <&dma 9 0 0x0>; /* Logical - MemToDev */
+ dma-names = "rx", "tx";
+ };
+
+ spi@8011a000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x8011a000 0x1000>;
+ interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ /* Same clock wired to kernel and pclk */
+ clocks = <&prcc_pclk 2 8>, <&prcc_pclk 2 8>;
+ clock-names = "spi0clk", "apb_pclk";
+ dmas = <&dma 0 0 0x2>, /* Logical - DevToMem */
+ <&dma 0 0 0x0>; /* Logical - MemToDev */
+ dma-names = "rx", "tx";
+ };
+
+ spi@80112000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x80112000 0x1000>;
+ interrupts = <0 96 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ /* Same clock wired to kernel and pclk */
+ clocks = <&prcc_pclk 2 2>, <&prcc_pclk 2 2>;
+ clock-names = "spi1clk", "apb_pclk";
+ dmas = <&dma 35 0 0x2>, /* Logical - DevToMem */
+ <&dma 35 0 0x0>; /* Logical - MemToDev */
+ dma-names = "rx", "tx";
+ };
+
+ spi@80111000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x80111000 0x1000>;
+ interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ /* Same clock wired to kernel and pclk */
+ clocks = <&prcc_pclk 2 1>, <&prcc_pclk 2 1>;
+ clock-names = "spi2clk", "apb_pclk";
+ dmas = <&dma 33 0 0x2>, /* Logical - DevToMem */
+ <&dma 33 0 0x0>; /* Logical - MemToDev */
+ dma-names = "rx", "tx";
+ };
+
+ spi@80129000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x80129000 0x1000>;
+ interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ /* Same clock wired to kernel and pclk */
+ clocks = <&prcc_pclk 1 7>, <&prcc_pclk 1 7>;
+ clock-names = "spi3clk", "apb_pclk";
+ dmas = <&dma 40 0 0x2>, /* Logical - DevToMem */
+ <&dma 40 0 0x0>; /* Logical - MemToDev */
+ dma-names = "rx", "tx";
};
uart@80120000 {
@@ -638,6 +789,9 @@
<&dma 13 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ clocks = <&prcc_kclk 1 0>, <&prcc_pclk 1 0>;
+ clock-names = "uart", "apb_pclk";
+
status = "disabled";
};
@@ -650,6 +804,9 @@
<&dma 12 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ clocks = <&prcc_kclk 1 1>, <&prcc_pclk 1 1>;
+ clock-names = "uart", "apb_pclk";
+
status = "disabled";
};
@@ -662,6 +819,9 @@
<&dma 11 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ clocks = <&prcc_kclk 3 6>, <&prcc_pclk 3 6>;
+ clock-names = "uart", "apb_pclk";
+
status = "disabled";
};
@@ -674,6 +834,9 @@
<&dma 29 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ clocks = <&prcc_kclk 1 5>, <&prcc_pclk 1 5>;
+ clock-names = "sdi", "apb_pclk";
+
status = "disabled";
};
@@ -686,6 +849,9 @@
<&dma 32 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ clocks = <&prcc_kclk 2 4>, <&prcc_pclk 2 6>;
+ clock-names = "sdi", "apb_pclk";
+
status = "disabled";
};
@@ -698,6 +864,9 @@
<&dma 28 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ clocks = <&prcc_kclk 3 4>, <&prcc_pclk 3 4>;
+ clock-names = "sdi", "apb_pclk";
+
status = "disabled";
};
@@ -705,6 +874,10 @@
compatible = "arm,pl18x", "arm,primecell";
reg = <0x80119000 0x1000>;
interrupts = <0 59 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&prcc_kclk 2 5>, <&prcc_pclk 2 7>;
+ clock-names = "sdi", "apb_pclk";
+
status = "disabled";
};
@@ -717,6 +890,9 @@
<&dma 42 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ clocks = <&prcc_kclk 2 2>, <&prcc_pclk 2 4>;
+ clock-names = "sdi", "apb_pclk";
+
status = "disabled";
};
@@ -724,6 +900,10 @@
compatible = "arm,pl18x", "arm,primecell";
reg = <0x80008000 0x1000>;
interrupts = <0 100 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&prcc_kclk 3 7>, <&prcc_pclk 3 7>;
+ clock-names = "sdi", "apb_pclk";
+
status = "disabled";
};
@@ -732,6 +912,10 @@
reg = <0x80123000 0x1000>;
interrupts = <0 31 IRQ_TYPE_LEVEL_HIGH>;
v-ape-supply = <&db8500_vape_reg>;
+
+ clocks = <&prcc_kclk 1 3>, <&prcc_pclk 1 3>;
+ clock-names = "msp", "apb_pclk";
+
status = "disabled";
};
@@ -740,6 +924,10 @@
reg = <0x80124000 0x1000>;
interrupts = <0 62 IRQ_TYPE_LEVEL_HIGH>;
v-ape-supply = <&db8500_vape_reg>;
+
+ clocks = <&prcc_kclk 1 4>, <&prcc_pclk 1 4>;
+ clock-names = "msp", "apb_pclk";
+
status = "disabled";
};
@@ -749,6 +937,10 @@
reg = <0x80117000 0x1000>;
interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>;
v-ape-supply = <&db8500_vape_reg>;
+
+ clocks = <&prcc_kclk 2 3>, <&prcc_pclk 2 5>;
+ clock-names = "msp", "apb_pclk";
+
status = "disabled";
};
@@ -757,6 +949,10 @@
reg = <0x80125000 0x1000>;
interrupts = <0 62 IRQ_TYPE_LEVEL_HIGH>;
v-ape-supply = <&db8500_vape_reg>;
+
+ clocks = <&prcc_kclk 1 10>, <&prcc_pclk 1 11>;
+ clock-names = "msp", "apb_pclk";
+
status = "disabled";
};
@@ -772,7 +968,7 @@
cpufreq-cooling {
compatible = "stericsson,db8500-cpufreq-cooling";
status = "disabled";
- };
+ };
vmmci: regulator-gpio {
compatible = "regulator-gpio";
@@ -797,6 +993,7 @@
interrupts = <0 15 IRQ_TYPE_LEVEL_HIGH>;
v-ape-supply = <&db8500_vape_reg>;
+ clocks = <&prcc_pclk 6 1>;
};
hash@a03c2000 {
@@ -804,6 +1001,7 @@
reg = <0xa03c2000 0x1000>;
v-ape-supply = <&db8500_vape_reg>;
+ clocks = <&prcc_pclk 6 2>;
};
};
};
diff --git a/arch/arm/boot/dts/ste-stuib.dtsi b/arch/arm/boot/dts/ste-href-stuib.dtsi
similarity index 95%
rename from arch/arm/boot/dts/ste-stuib.dtsi
rename to arch/arm/boot/dts/ste-href-stuib.dtsi
index 524e332..76704ec 100644
--- a/arch/arm/boot/dts/ste-stuib.dtsi
+++ b/arch/arm/boot/dts/ste-href-stuib.dtsi
@@ -57,7 +57,6 @@
bu21013_tp@5c {
compatible = "rohm,bu21013_tp";
reg = <0x5c>;
- touch-gpio = <&gpio2 20 0x4>;
avdd-supply = <&ab8500_ldo_aux1_reg>;
rohm,touch-max-x = <384>;
@@ -68,7 +67,6 @@
bu21013_tp@5d {
compatible = "rohm,bu21013_tp";
reg = <0x5d>;
- touch-gpio = <&gpio2 20 0x4>;
avdd-supply = <&ab8500_ldo_aux1_reg>;
rohm,touch-max-x = <384>;
diff --git a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
new file mode 100644
index 0000000..76d3ef1
--- /dev/null
+++ b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
@@ -0,0 +1,41 @@
+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ *
+ * Device Tree for the TVK1281618 UIB
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ soc {
+ /* Add Synaptics touch screen, TC35892 keypad etc here */
+ i2c@80004000 {
+ tc3589x@44 {
+ compatible = "tc3589x";
+ reg = <0x44>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <26 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ tc3589x_gpio {
+ compatible = "tc3589x-gpio";
+ interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 370e03f..aa3f020 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -41,28 +41,6 @@
status = "okay";
};
- i2c@80004000 {
- tc3589x@42 {
- compatible = "tc3589x";
- reg = <0x42>;
- interrupt-parent = <&gpio6>;
- interrupts = <25 IRQ_TYPE_EDGE_RISING>;
-
- interrupt-controller;
- #interrupt-cells = <2>;
-
- tc3589x_gpio: tc3589x_gpio {
- compatible = "tc3589x-gpio";
- interrupts = <0 IRQ_TYPE_EDGE_RISING>;
-
- interrupt-controller;
- #interrupt-cells = <2>;
- gpio-controller;
- #gpio-cells = <2>;
- };
- };
- };
-
i2c@80128000 {
lp5521@33 {
compatible = "national,lp5521";
@@ -72,6 +50,7 @@
chan0 {
led-cur = /bits/ 8 <0x2f>;
max-cur = /bits/ 8 <0x5f>;
+ linux,default-trigger = "heartbeat";
};
chan1 {
led-cur = /bits/ 8 <0x2f>;
@@ -102,7 +81,7 @@
};
bh1780@29 {
compatible = "rohm,bh1780gli";
- reg = <0x33>;
+ reg = <0x29>;
};
};
@@ -167,89 +146,11 @@
};
prcmu@80157000 {
- db8500-prcmu-regulators {
- db8500_vape_reg: db8500_vape {
- regulator-name = "db8500-vape";
- };
-
- db8500_varm_reg: db8500_varm {
- regulator-name = "db8500-varm";
- };
-
- db8500_vmodem_reg: db8500_vmodem {
- regulator-name = "db8500-vmodem";
- };
-
- db8500_vpll_reg: db8500_vpll {
- regulator-name = "db8500-vpll";
- };
-
- db8500_vsmps1_reg: db8500_vsmps1 {
- regulator-name = "db8500-vsmps1";
- };
-
- db8500_vsmps2_reg: db8500_vsmps2 {
- regulator-name = "db8500-vsmps2";
- };
-
- db8500_vsmps3_reg: db8500_vsmps3 {
- regulator-name = "db8500-vsmps3";
- };
-
- db8500_vrf1_reg: db8500_vrf1 {
- regulator-name = "db8500-vrf1";
- };
-
- db8500_sva_mmdsp_reg: db8500_sva_mmdsp {
- regulator-name = "db8500-sva-mmdsp";
- };
-
- db8500_sva_mmdsp_ret_reg: db8500_sva_mmdsp_ret {
- regulator-name = "db8500-sva-mmdsp-ret";
- };
-
- db8500_sva_pipe_reg: db8500_sva_pipe {
- regulator-name = "db8500_sva_pipe";
- };
-
- db8500_sia_mmdsp_reg: db8500_sia_mmdsp {
- regulator-name = "db8500_sia_mmdsp";
- };
-
- db8500_sia_mmdsp_ret_reg: db8500_sia_mmdsp_ret {
- regulator-name = "db8500-sia-mmdsp-ret";
- };
-
- db8500_sia_pipe_reg: db8500_sia_pipe {
- regulator-name = "db8500-sia-pipe";
- };
-
- db8500_sga_reg: db8500_sga {
- regulator-name = "db8500-sga";
- };
-
- db8500_b2r2_mcde_reg: db8500_b2r2_mcde {
- regulator-name = "db8500-b2r2-mcde";
- };
-
- db8500_esram12_reg: db8500_esram12 {
- regulator-name = "db8500-esram12";
- };
-
- db8500_esram12_ret_reg: db8500_esram12_ret {
- regulator-name = "db8500-esram12-ret";
- };
-
- db8500_esram34_reg: db8500_esram34 {
- regulator-name = "db8500-esram34";
- };
-
- db8500_esram34_ret_reg: db8500_esram34_ret {
- regulator-name = "db8500-esram34-ret";
- };
- };
-
ab8500 {
+ ab8500-gpio {
+ compatible = "stericsson,ab8500-gpio";
+ };
+
ab8500-regulators {
ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
regulator-name = "V-DISPLAY";
diff --git a/arch/arm/boot/dts/ste-hrefprev60-stuib.dts b/arch/arm/boot/dts/ste-hrefprev60-stuib.dts
new file mode 100644
index 0000000..2b1cb5b
--- /dev/null
+++ b/arch/arm/boot/dts/ste-hrefprev60-stuib.dts
@@ -0,0 +1,34 @@
+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "ste-hrefprev60.dtsi"
+#include "ste-href-stuib.dtsi"
+
+/ {
+ model = "ST-Ericsson HREF (pre-v60) and ST UIB";
+ compatible = "st-ericsson,mop500", "st-ericsson,u8500";
+
+ soc {
+ /* Reset line for the BU21013 touchscreen */
+ i2c@80110000 {
+ /* Only one of these will be used */
+ bu21013_tp@5c {
+ touch-gpio = <&gpio2 12 0x4>;
+ reset-gpio = <&tc3589x_gpio 13 0x4>;
+ };
+ bu21013_tp@5d {
+ touch-gpio = <&gpio2 12 0x4>;
+ reset-gpio = <&tc3589x_gpio 13 0x4>;
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/ste-hrefprev60-tvk.dts b/arch/arm/boot/dts/ste-hrefprev60-tvk.dts
new file mode 100644
index 0000000..59523f8
--- /dev/null
+++ b/arch/arm/boot/dts/ste-hrefprev60-tvk.dts
@@ -0,0 +1,19 @@
+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "ste-hrefprev60.dtsi"
+#include "ste-href-tvk1281618.dtsi"
+
+/ {
+ model = "ST-Ericsson HREF (pre-v60) and TVK1281618 UIB";
+ compatible = "st-ericsson,mop500", "st-ericsson,u8500";
+};
diff --git a/arch/arm/boot/dts/ste-hrefprev60.dts b/arch/arm/boot/dts/ste-hrefprev60.dtsi
similarity index 60%
rename from arch/arm/boot/dts/ste-hrefprev60.dts
rename to arch/arm/boot/dts/ste-hrefprev60.dtsi
index d8d3b99..b2cd7bc 100644
--- a/arch/arm/boot/dts/ste-hrefprev60.dts
+++ b/arch/arm/boot/dts/ste-hrefprev60.dtsi
@@ -7,17 +7,14 @@
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
+ *
+ * Device Tree for the HREF+ prior to the v60 variant.
*/
-/dts-v1/;
#include "ste-dbx5x0.dtsi"
#include "ste-href.dtsi"
-#include "ste-stuib.dtsi"
/ {
- model = "ST-Ericsson HREF (pre-v60) platform with Device Tree";
- compatible = "st-ericsson,mop500", "st-ericsson,u8500";
-
gpio_keys {
button@1 {
gpios = <&tc3589x_gpio 7 0x4>;
@@ -25,24 +22,30 @@
};
soc {
- prcmu@80157000 {
- ab8500@5 {
- ab8500-gpio {
- compatible = "stericsson,ab8500-gpio";
- };
- };
- };
-
i2c@80004000 {
tps61052@33 {
compatible = "tps61052";
reg = <0x33>;
};
- };
- i2c@80110000 {
- bu21013_tp@5c {
- reset-gpio = <&tc3589x_gpio 13 0x4>;
+ tc3589x@42 {
+ compatible = "tc3589x";
+ reg = <0x42>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <25 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ tc3589x_gpio: tc3589x_gpio {
+ compatible = "tc3589x-gpio";
+ interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
};
};
diff --git a/arch/arm/boot/dts/ste-hrefv60plus-stuib.dts b/arch/arm/boot/dts/ste-hrefv60plus-stuib.dts
new file mode 100644
index 0000000..8c6a2de
--- /dev/null
+++ b/arch/arm/boot/dts/ste-hrefv60plus-stuib.dts
@@ -0,0 +1,36 @@
+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ *
+ * Device Tree for the HREF version 60 or later with the ST UIB
+ */
+
+/dts-v1/;
+#include "ste-hrefv60plus.dtsi"
+#include "ste-href-stuib.dtsi"
+
+/ {
+ model = "ST-Ericsson HREF (v60+) and ST UIB";
+ compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
+
+ soc {
+ /* Reset line for the BU21013 touchscreen */
+ i2c@80110000 {
+ /* Only one of these will be used */
+ bu21013_tp@5c {
+ touch-gpio = <&gpio2 20 0x4>;
+ reset-gpio = <&gpio4 17 0x4>;
+ };
+ bu21013_tp@5d {
+ touch-gpio = <&gpio2 20 0x4>;
+ reset-gpio = <&gpio4 17 0x4>;
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts b/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts
new file mode 100644
index 0000000..d53cccd
--- /dev/null
+++ b/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts
@@ -0,0 +1,21 @@
+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ *
+ * Device Tree for the HREF version 60 or later with the TVK1281618 UIB
+ */
+
+/dts-v1/;
+#include "ste-hrefv60plus.dtsi"
+#include "ste-href-tvk1281618.dtsi"
+
+/ {
+ model = "ST-Ericsson HREF (v60+) and TVK1281618 UIB";
+ compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
+};
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dts b/arch/arm/boot/dts/ste-hrefv60plus.dts
deleted file mode 100644
index 6e52ebb..0000000
--- a/arch/arm/boot/dts/ste-hrefv60plus.dts
+++ /dev/null
@@ -1,210 +0,0 @@
-/*
- * Copyright 2012 ST-Ericsson AB
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-/dts-v1/;
-#include "ste-dbx5x0.dtsi"
-#include "ste-href.dtsi"
-#include "ste-stuib.dtsi"
-
-/ {
- model = "ST-Ericsson HREF (v60+) platform with Device Tree";
- compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
-
- gpio_keys {
- button@1 {
- gpios = <&gpio6 25 0x4>;
- };
- };
-
- soc {
- i2c@80110000 {
- bu21013_tp@0x5c {
- reset-gpio = <&gpio4 15 0x4>;
- };
- };
-
- // External Micro SD slot
- sdi0_per1@80126000 {
- arm,primecell-periphid = <0x10480180>;
- max-frequency = <100000000>;
- bus-width = <4>;
- mmc-cap-sd-highspeed;
- mmc-cap-mmc-highspeed;
- vmmc-supply = <&ab8500_ldo_aux3_reg>;
-
- cd-gpios = <&tc3589x_gpio 3 0x4>;
-
- status = "okay";
- };
-
- // WLAN SDIO channel
- sdi1_per2@80118000 {
- arm,primecell-periphid = <0x10480180>;
- max-frequency = <100000000>;
- bus-width = <4>;
-
- status = "okay";
- };
-
- // PoP:ed eMMC
- sdi2_per3@80005000 {
- arm,primecell-periphid = <0x10480180>;
- max-frequency = <100000000>;
- bus-width = <8>;
- mmc-cap-mmc-highspeed;
-
- status = "okay";
- };
-
- // On-board eMMC
- sdi4_per2@80114000 {
- arm,primecell-periphid = <0x10480180>;
- max-frequency = <100000000>;
- bus-width = <8>;
- mmc-cap-mmc-highspeed;
- vmmc-supply = <&ab8500_ldo_aux2_reg>;
-
- status = "okay";
- };
-
- prcmu@80157000 {
- db8500-prcmu-regulators {
- db8500_vape_reg: db8500_vape {
- regulator-name = "db8500-vape";
- };
-
- db8500_varm_reg: db8500_varm {
- regulator-name = "db8500-varm";
- };
-
- db8500_vmodem_reg: db8500_vmodem {
- regulator-name = "db8500-vmodem";
- };
-
- db8500_vpll_reg: db8500_vpll {
- regulator-name = "db8500-vpll";
- };
-
- db8500_vsmps1_reg: db8500_vsmps1 {
- regulator-name = "db8500-vsmps1";
- };
-
- db8500_vsmps2_reg: db8500_vsmps2 {
- regulator-name = "db8500-vsmps2";
- };
-
- db8500_vsmps3_reg: db8500_vsmps3 {
- regulator-name = "db8500-vsmps3";
- };
-
- db8500_vrf1_reg: db8500_vrf1 {
- regulator-name = "db8500-vrf1";
- };
-
- db8500_sva_mmdsp_reg: db8500_sva_mmdsp {
- regulator-name = "db8500-sva-mmdsp";
- };
-
- db8500_sva_mmdsp_ret_reg: db8500_sva_mmdsp_ret {
- regulator-name = "db8500-sva-mmdsp-ret";
- };
-
- db8500_sva_pipe_reg: db8500_sva_pipe {
- regulator-name = "db8500_sva_pipe";
- };
-
- db8500_sia_mmdsp_reg: db8500_sia_mmdsp {
- regulator-name = "db8500_sia_mmdsp";
- };
-
- db8500_sia_mmdsp_ret_reg: db8500_sia_mmdsp_ret {
- regulator-name = "db8500-sia-mmdsp-ret";
- };
-
- db8500_sia_pipe_reg: db8500_sia_pipe {
- regulator-name = "db8500-sia-pipe";
- };
-
- db8500_sga_reg: db8500_sga {
- regulator-name = "db8500-sga";
- };
-
- db8500_b2r2_mcde_reg: db8500_b2r2_mcde {
- regulator-name = "db8500-b2r2-mcde";
- };
-
- db8500_esram12_reg: db8500_esram12 {
- regulator-name = "db8500-esram12";
- };
-
- db8500_esram12_ret_reg: db8500_esram12_ret {
- regulator-name = "db8500-esram12-ret";
- };
-
- db8500_esram34_reg: db8500_esram34 {
- regulator-name = "db8500-esram34";
- };
-
- db8500_esram34_ret_reg: db8500_esram34_ret {
- regulator-name = "db8500-esram34-ret";
- };
- };
-
- ab8500 {
- ab8500-regulators {
- ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
- regulator-name = "V-DISPLAY";
- };
-
- ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
- regulator-name = "V-eMMC1";
- };
-
- ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
- regulator-name = "V-MMC-SD";
- };
-
- ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
- regulator-name = "V-INTCORE";
- };
-
- ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
- regulator-name = "V-TVOUT";
- };
-
- ab8500_ldo_usb_reg: ab8500_ldo_usb {
- regulator-name = "dummy";
- };
-
- ab8500_ldo_audio_reg: ab8500_ldo_audio {
- regulator-name = "V-AUD";
- };
-
- ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
- regulator-name = "V-AMIC1";
- };
-
- ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
- regulator-name = "V-AMIC2";
- };
-
- ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
- regulator-name = "V-DMIC";
- };
-
- ab8500_ldo_ana_reg: ab8500_ldo_ana {
- regulator-name = "V-CSI/DSI";
- };
- };
- };
- };
- };
-};
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
new file mode 100644
index 0000000..aed511b
--- /dev/null
+++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
@@ -0,0 +1,70 @@
+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include "ste-dbx5x0.dtsi"
+#include "ste-href.dtsi"
+
+/ {
+ model = "ST-Ericsson HREF (v60+) platform with Device Tree";
+ compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
+
+ gpio_keys {
+ button@1 {
+ gpios = <&gpio5 25 0x4>;
+ };
+ };
+
+ soc {
+ // External Micro SD slot
+ sdi0_per1@80126000 {
+ arm,primecell-periphid = <0x10480180>;
+ max-frequency = <100000000>;
+ bus-width = <4>;
+ mmc-cap-sd-highspeed;
+ mmc-cap-mmc-highspeed;
+ vmmc-supply = <&ab8500_ldo_aux3_reg>;
+
+ cd-gpios = <&gpio2 31 0x4>; // 95
+
+ status = "okay";
+ };
+
+ // WLAN SDIO channel
+ sdi1_per2@80118000 {
+ arm,primecell-periphid = <0x10480180>;
+ max-frequency = <100000000>;
+ bus-width = <4>;
+
+ status = "okay";
+ };
+
+ // PoP:ed eMMC
+ sdi2_per3@80005000 {
+ arm,primecell-periphid = <0x10480180>;
+ max-frequency = <100000000>;
+ bus-width = <8>;
+ mmc-cap-mmc-highspeed;
+
+ status = "okay";
+ };
+
+ // On-board eMMC
+ sdi4_per2@80114000 {
+ arm,primecell-periphid = <0x10480180>;
+ max-frequency = <100000000>;
+ bus-width = <8>;
+ mmc-cap-mmc-highspeed;
+ vmmc-supply = <&ab8500_ldo_aux2_reg>;
+
+ status = "okay";
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index f1fc128..f0b39f8 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -111,12 +111,13 @@
vdd33a-supply = <&en_3v3_reg>;
vddvario-supply = <&db8500_vape_reg>;
-
reg-shift = <1>;
reg-io-width = <2>;
smsc,force-internal-phy;
smsc,irq-active-high;
smsc,irq-push-pull;
+
+ clocks = <&prcc_pclk 3 0>;
};
};
@@ -170,86 +171,8 @@
};
prcmu@80157000 {
- db8500-prcmu-regulators {
- db8500_vape_reg: db8500_vape {
- regulator-name = "db8500-vape";
- };
-
- db8500_varm_reg: db8500_varm {
- regulator-name = "db8500-varm";
- };
-
- db8500_vmodem_reg: db8500_vmodem {
- regulator-name = "db8500-vmodem";
- };
-
- db8500_vpll_reg: db8500_vpll {
- regulator-name = "db8500-vpll";
- };
-
- db8500_vsmps1_reg: db8500_vsmps1 {
- regulator-name = "db8500-vsmps1";
- };
-
- db8500_vsmps2_reg: db8500_vsmps2 {
- regulator-name = "db8500-vsmps2";
- };
-
- db8500_vsmps3_reg: db8500_vsmps3 {
- regulator-name = "db8500-vsmps3";
- };
-
- db8500_vrf1_reg: db8500_vrf1 {
- regulator-name = "db8500-vrf1";
- };
-
- db8500_sva_mmdsp_reg: db8500_sva_mmdsp {
- regulator-name = "db8500-sva-mmdsp";
- };
-
- db8500_sva_mmdsp_ret_reg: db8500_sva_mmdsp_ret {
- regulator-name = "db8500-sva-mmdsp-ret";
- };
-
- db8500_sva_pipe_reg: db8500_sva_pipe {
- regulator-name = "db8500_sva_pipe";
- };
-
- db8500_sia_mmdsp_reg: db8500_sia_mmdsp {
- regulator-name = "db8500_sia_mmdsp";
- };
-
- db8500_sia_mmdsp_ret_reg: db8500_sia_mmdsp_ret {
- regulator-name = "db8500-sia-mmdsp-ret";
- };
-
- db8500_sia_pipe_reg: db8500_sia_pipe {
- regulator-name = "db8500-sia-pipe";
- };
-
- db8500_sga_reg: db8500_sga {
- regulator-name = "db8500-sga";
- };
-
- db8500_b2r2_mcde_reg: db8500_b2r2_mcde {
- regulator-name = "db8500-b2r2-mcde";
- };
-
- db8500_esram12_reg: db8500_esram12 {
- regulator-name = "db8500-esram12";
- };
-
- db8500_esram12_ret_reg: db8500_esram12_ret {
- regulator-name = "db8500-esram12-ret";
- };
-
- db8500_esram34_reg: db8500_esram34 {
- regulator-name = "db8500-esram34";
- };
-
- db8500_esram34_ret_reg: db8500_esram34_ret {
- regulator-name = "db8500-esram34-ret";
- };
+ cpufreq {
+ status = "okay";
};
thermal@801573c0 {
diff --git a/arch/arm/boot/dts/sun4i-a10.dtsi b/arch/arm/boot/dts/sun4i-a10.dtsi
index c32770a..319cc6b 100644
--- a/arch/arm/boot/dts/sun4i-a10.dtsi
+++ b/arch/arm/boot/dts/sun4i-a10.dtsi
@@ -266,6 +266,11 @@
reg = <0x01c20c90 0x10>;
};
+ sid: eeprom@01c23800 {
+ compatible = "allwinner,sun4i-sid";
+ reg = <0x01c23800 0x10>;
+ };
+
uart0: serial@01c28000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28000 0x400>;
diff --git a/arch/arm/boot/dts/sun5i-a10s.dtsi b/arch/arm/boot/dts/sun5i-a10s.dtsi
index 3b4a057..5247674 100644
--- a/arch/arm/boot/dts/sun5i-a10s.dtsi
+++ b/arch/arm/boot/dts/sun5i-a10s.dtsi
@@ -255,6 +255,11 @@
reg = <0x01c20c90 0x10>;
};
+ sid: eeprom@01c23800 {
+ compatible = "allwinner,sun4i-sid";
+ reg = <0x01c23800 0x10>;
+ };
+
uart0: serial@01c28000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28000 0x400>;
diff --git a/arch/arm/boot/dts/sun5i-a13.dtsi b/arch/arm/boot/dts/sun5i-a13.dtsi
index f6091dc..ce8ef2a 100644
--- a/arch/arm/boot/dts/sun5i-a13.dtsi
+++ b/arch/arm/boot/dts/sun5i-a13.dtsi
@@ -222,6 +222,11 @@
reg = <0x01c20c90 0x10>;
};
+ sid: eeprom@01c23800 {
+ compatible = "allwinner,sun4i-sid";
+ reg = <0x01c23800 0x10>;
+ };
+
uart1: serial@01c28400 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28400 0x400>;
diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi
index f244f5f..c1751a6 100644
--- a/arch/arm/boot/dts/sun6i-a31.dtsi
+++ b/arch/arm/boot/dts/sun6i-a31.dtsi
@@ -175,7 +175,7 @@
apb2_gates: apb2_gates@01c2006c {
#clock-cells = <1>;
compatible = "allwinner,sun6i-a31-apb2-gates-clk";
- reg = <0x01c2006c 0x8>;
+ reg = <0x01c2006c 0x4>;
clocks = <&apb2>;
clock-output-names = "apb2_i2c0", "apb2_i2c1",
"apb2_i2c2", "apb2_i2c3", "apb2_uart0",
diff --git a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts b/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts
index 15e625e..5c51cb8 100644
--- a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts
+++ b/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts
@@ -48,6 +48,18 @@
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
+
+ i2c0: i2c@01c2ac00 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+ };
+
+ i2c1: i2c@01c2b000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+ };
};
leds {
diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
new file mode 100644
index 0000000..8a1009d
--- /dev/null
+++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
@@ -0,0 +1,63 @@
+/*
+ * Copyright 2013 Oliver Schinagl
+ *
+ * Oliver Schinagl <oliver@schinagl.nl>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "sun7i-a20.dtsi"
+
+/ {
+ model = "Cubietech Cubietruck";
+ compatible = "cubietech,cubietruck", "allwinner,sun7i-a20";
+
+ soc@01c00000 {
+ pinctrl@01c20800 {
+ led_pins_cubietruck: led_pins@0 {
+ allwinner,pins = "PH7", "PH11", "PH20", "PH21";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <0>;
+ allwinner,pull = <0>;
+ };
+ };
+
+ uart0: serial@01c28000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_cubietruck>;
+
+ blue {
+ label = "cubietruck:blue:usr";
+ gpios = <&pio 7 21 0>;
+ };
+
+ orange {
+ label = "cubietruck:orange:usr";
+ gpios = <&pio 7 20 0>;
+ };
+
+ white {
+ label = "cubietruck:white:usr";
+ gpios = <&pio 7 11 0>;
+ };
+
+ green {
+ label = "cubietruck:green:usr";
+ gpios = <&pio 7 7 0>;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts
index 9e77855..ead3013 100644
--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts
+++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts
@@ -60,6 +60,24 @@
pinctrl-0 = <&uart7_pins_a>;
status = "okay";
};
+
+ i2c0: i2c@01c2ac00 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+ };
+
+ i2c1: i2c@01c2b000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+ };
+
+ i2c2: i2c@01c2b400 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+ };
};
leds {
diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi
index 80559cb..e46cfed 100644
--- a/arch/arm/boot/dts/sun7i-a20.dtsi
+++ b/arch/arm/boot/dts/sun7i-a20.dtsi
@@ -215,6 +215,27 @@
allwinner,pull = <0>;
};
+ i2c0_pins_a: i2c0@0 {
+ allwinner,pins = "PB0", "PB1";
+ allwinner,function = "i2c0";
+ allwinner,drive = <0>;
+ allwinner,pull = <0>;
+ };
+
+ i2c1_pins_a: i2c1@0 {
+ allwinner,pins = "PB18", "PB19";
+ allwinner,function = "i2c1";
+ allwinner,drive = <0>;
+ allwinner,pull = <0>;
+ };
+
+ i2c2_pins_a: i2c2@0 {
+ allwinner,pins = "PB20", "PB21";
+ allwinner,function = "i2c2";
+ allwinner,drive = <0>;
+ allwinner,pull = <0>;
+ };
+
emac_pins_a: emac0@0 {
allwinner,pins = "PA0", "PA1", "PA2",
"PA3", "PA4", "PA5", "PA6",
@@ -244,6 +265,11 @@
reg = <0x01c20c90 0x10>;
};
+ sid: eeprom@01c23800 {
+ compatible = "allwinner,sun7i-a20-sid";
+ reg = <0x01c23800 0x200>;
+ };
+
uart0: serial@01c28000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28000 0x400>;
@@ -324,6 +350,51 @@
status = "disabled";
};
+ i2c0: i2c@01c2ac00 {
+ compatible = "allwinner,sun4i-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <0 7 1>;
+ clocks = <&apb1_gates 0>;
+ clock-frequency = <100000>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@01c2b000 {
+ compatible = "allwinner,sun4i-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <0 8 1>;
+ clocks = <&apb1_gates 1>;
+ clock-frequency = <100000>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@01c2b400 {
+ compatible = "allwinner,sun4i-i2c";
+ reg = <0x01c2b400 0x400>;
+ interrupts = <0 9 1>;
+ clocks = <&apb1_gates 2>;
+ clock-frequency = <100000>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@01c2b800 {
+ compatible = "allwinner,sun4i-i2c";
+ reg = <0x01c2b800 0x400>;
+ interrupts = <0 88 1>;
+ clocks = <&apb1_gates 3>;
+ clock-frequency = <100000>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@01c2bc00 {
+ compatible = "allwinner,sun4i-i2c";
+ reg = <0x01c2bc00 0x400>;
+ interrupts = <0 89 1>;
+ clocks = <&apb1_gates 15>;
+ clock-frequency = <100000>;
+ status = "disabled";
+ };
+
gic: interrupt-controller@01c81000 {
compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
reg = <0x01c81000 0x1000>,
diff --git a/arch/arm/boot/dts/tegra114-dalmore.dts b/arch/arm/boot/dts/tegra114-dalmore.dts
index 6023028..cb5ec23 100644
--- a/arch/arm/boot/dts/tegra114-dalmore.dts
+++ b/arch/arm/boot/dts/tegra114-dalmore.dts
@@ -1,5 +1,6 @@
/dts-v1/;
+#include <dt-bindings/input/input.h>
#include "tegra114.dtsi"
/ {
@@ -738,6 +739,14 @@
realtek,ldo1-en-gpios =
<&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
};
+
+ temperature-sensor@4c {
+ compatible = "onnn,nct1008";
+ reg = <0x4c>;
+ vcc-supply = <&palmas_ldo6_reg>;
+ interrupt-parent = <&gpio>;
+ interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_LEVEL_LOW>;
+ };
};
i2c@7000d000 {
@@ -947,7 +956,7 @@
regulator-max-microvolt = <1800000>;
};
- ldo6 {
+ palmas_ldo6_reg: ldo6 {
regulator-name = "vdd-sensor-2v85";
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <2850000>;
@@ -1011,6 +1020,19 @@
interrupt-parent = <&palmas>;
interrupts = <8 0>;
};
+
+ pinmux {
+ compatible = "ti,tps65913-pinctrl";
+ pinctrl-names = "default";
+ pinctrl-0 = <&palmas_default>;
+
+ palmas_default: pinmux {
+ pin_gpio6 {
+ pins = "gpio6";
+ function = "gpio";
+ };
+ };
+ };
};
};
@@ -1081,26 +1103,26 @@
home {
label = "Home";
gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
- linux,code = <102>; /* KEY_HOME */
+ linux,code = <KEY_HOME>;
};
power {
label = "Power";
gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
- linux,code = <116>; /* KEY_POWER */
+ linux,code = <KEY_POWER>;
gpio-key,wakeup;
};
volume_down {
label = "Volume Down";
gpios = <&gpio TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>;
- linux,code = <114>; /* KEY_VOLUMEDOWN */
+ linux,code = <KEY_VOLUMEDOWN>;
};
volume_up {
label = "Volume Up";
gpios = <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_LOW>;
- linux,code = <115>; /* KEY_VOLUMEUP */
+ linux,code = <KEY_VOLUMEUP>;
};
};
diff --git a/arch/arm/boot/dts/tegra124-venice2.dts b/arch/arm/boot/dts/tegra124-venice2.dts
new file mode 100644
index 0000000..431d67a
--- /dev/null
+++ b/arch/arm/boot/dts/tegra124-venice2.dts
@@ -0,0 +1,27 @@
+/dts-v1/;
+
+#include "tegra124.dtsi"
+
+/ {
+ model = "NVIDIA Tegra124 Venice2";
+ compatible = "nvidia,venice2", "nvidia,tegra124";
+
+ memory {
+ reg = <0x80000000 0x80000000>;
+ };
+
+ serial@70006000 {
+ status = "okay";
+ };
+
+ pmc@7000e400 {
+ nvidia,invert-interrupt;
+ nvidia,suspend-mode = <1>;
+ nvidia,cpu-pwr-good-time = <500>;
+ nvidia,cpu-pwr-off-time = <300>;
+ nvidia,core-pwr-good-time = <641 3845>;
+ nvidia,core-pwr-off-time = <61036>;
+ nvidia,core-power-req-active-high;
+ nvidia,sys-clock-req-active-high;
+ };
+};
diff --git a/arch/arm/boot/dts/tegra124.dtsi b/arch/arm/boot/dts/tegra124.dtsi
new file mode 100644
index 0000000..b741300
--- /dev/null
+++ b/arch/arm/boot/dts/tegra124.dtsi
@@ -0,0 +1,149 @@
+#include <dt-bindings/gpio/tegra-gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+#include "skeleton.dtsi"
+
+/ {
+ compatible = "nvidia,tegra124";
+ interrupt-parent = <&gic>;
+
+ gic: interrupt-controller@50041000 {
+ compatible = "arm,cortex-a15-gic";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x50041000 0x1000>,
+ <0x50042000 0x1000>,
+ <0x50044000 0x2000>,
+ <0x50046000 0x2000>;
+ interrupts = <GIC_PPI 9
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ timer@60005000 {
+ compatible = "nvidia,tegra124-timer", "nvidia,tegra20-timer";
+ reg = <0x60005000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpio: gpio@6000d000 {
+ compatible = "nvidia,tegra124-gpio", "nvidia,tegra30-gpio";
+ reg = <0x6000d000 0x1000>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ };
+
+ /*
+ * There are two serial driver i.e. 8250 based simple serial
+ * driver and APB DMA based serial driver for higher baudrate
+ * and performace. To enable the 8250 based driver, the compatible
+ * is "nvidia,tegra124-uart", "nvidia,tegra20-uart" and to enable
+ * the APB DMA based serial driver, the comptible is
+ * "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart".
+ */
+ serial@70006000 {
+ compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart";
+ reg = <0x70006000 0x40>;
+ reg-shift = <2>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ serial@70006040 {
+ compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart";
+ reg = <0x70006040 0x40>;
+ reg-shift = <2>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ serial@70006200 {
+ compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart";
+ reg = <0x70006200 0x40>;
+ reg-shift = <2>;
+ interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ serial@70006300 {
+ compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart";
+ reg = <0x70006300 0x40>;
+ reg-shift = <2>;
+ interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ serial@70006400 {
+ compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart";
+ reg = <0x70006400 0x40>;
+ reg-shift = <2>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ rtc@7000e000 {
+ compatible = "nvidia,tegra124-rtc", "nvidia,tegra20-rtc";
+ reg = <0x7000e000 0x100>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pmc@7000e400 {
+ compatible = "nvidia,tegra124-pmc";
+ reg = <0x7000e400 0x400>;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <0>;
+ };
+
+ cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <1>;
+ };
+
+ cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <2>;
+ };
+
+ cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <3>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+};
diff --git a/arch/arm/boot/dts/tegra30-cardhu.dtsi b/arch/arm/boot/dts/tegra30-cardhu.dtsi
index e19dbf2..5ea7dfa 100644
--- a/arch/arm/boot/dts/tegra30-cardhu.dtsi
+++ b/arch/arm/boot/dts/tegra30-cardhu.dtsi
@@ -294,9 +294,10 @@
};
};
- nct1008 {
+ temperature-sensor@4c {
compatible = "onnn,nct1008";
reg = <0x4c>;
+ vcc-supply = <&sys_3v3_reg>;
interrupt-parent = <&gpio>;
interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_LEVEL_LOW>;
};
diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/tegra30.dtsi
index 0022c12..2bd55cf 100644
--- a/arch/arm/boot/dts/tegra30.dtsi
+++ b/arch/arm/boot/dts/tegra30.dtsi
@@ -136,12 +136,13 @@
gr3d {
compatible = "nvidia,tegra30-gr3d";
reg = <0x54180000 0x00040000>;
- clocks = <&tegra_car 24 &tegra_car 98>;
+ clocks = <&tegra_car TEGRA30_CLK_GR3D
+ &tegra_car TEGRA30_CLK_GR3D2>;
clock-names = "3d", "3d2";
};
dc@54200000 {
- compatible = "nvidia,tegra30-dc";
+ compatible = "nvidia,tegra30-dc", "nvidia,tegra20-dc";
reg = <0x54200000 0x00040000>;
interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&tegra_car TEGRA30_CLK_DISP1>,
diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/twl4030.dtsi
index ae6a17a..af7fa40 100644
--- a/arch/arm/boot/dts/twl4030.dtsi
+++ b/arch/arm/boot/dts/twl4030.dtsi
@@ -23,6 +23,22 @@
compatible = "ti,twl4030-wdt";
};
+ vaux1: regulator-vaux1 {
+ compatible = "ti,twl4030-vaux1";
+ };
+
+ vaux2: regulator-vaux2 {
+ compatible = "ti,twl4030-vaux2";
+ };
+
+ vaux3: regulator-vaux3 {
+ compatible = "ti,twl4030-vaux3";
+ };
+
+ vaux4: regulator-vaux4 {
+ compatible = "ti,twl4030-vaux4";
+ };
+
vcc: regulator-vdd1 {
compatible = "ti,twl4030-vdd1";
regulator-min-microvolt = <600000>;
@@ -35,10 +51,20 @@
regulator-max-microvolt = <1800000>;
};
- vpll2: regulator-vpll2 {
- compatible = "ti,twl4030-vpll2";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
+ vio: regulator-vio {
+ compatible = "ti,twl4030-vio";
+ };
+
+ vintana1: regulator-vintana1 {
+ compatible = "ti,twl4030-vintana1";
+ };
+
+ vintana2: regulator-vintana2 {
+ compatible = "ti,twl4030-vintana2";
+ };
+
+ vintdig: regulator-vintdig {
+ compatible = "ti,twl4030-vintdig";
};
vmmc1: regulator-vmmc1 {
@@ -65,6 +91,16 @@
compatible = "ti,twl4030-vusb3v1";
};
+ vpll1: regulator-vpll1 {
+ compatible = "ti,twl4030-vpll1";
+ };
+
+ vpll2: regulator-vpll2 {
+ compatible = "ti,twl4030-vpll2";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
vsim: regulator-vsim {
compatible = "ti,twl4030-vsim";
regulator-min-microvolt = <1800000>;
@@ -97,4 +133,9 @@
compatible = "ti,twl4030-pwmled";
#pwm-cells = <2>;
};
+
+ twl_pwrbutton: pwrbutton {
+ compatible = "ti,twl4030-pwrbutton";
+ interrupts = <8>;
+ };
};
diff --git a/arch/arm/boot/dts/twl6030_omap4.dtsi b/arch/arm/boot/dts/twl6030_omap4.dtsi
new file mode 100644
index 0000000..a4fa570
--- /dev/null
+++ b/arch/arm/boot/dts/twl6030_omap4.dtsi
@@ -0,0 +1,38 @@
+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+&twl {
+ /*
+ * On most OMAP4 platforms, the twl6030 IRQ line is connected
+ * to the SYS_NIRQ1 line on OMAP and the twl6030 MSECURE line is
+ * connected to the fref_clk0_out.sys_drm_msecure line.
+ * Therefore, configure the defaults for the SYS_NIRQ1 and
+ * fref_clk0_out.sys_drm_msecure pins here.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &twl6030_pins
+ &twl6030_wkup_pins
+ >;
+};
+
+&omap4_pmx_wkup {
+ twl6030_wkup_pins: pinmux_twl6030_wkup_pins {
+ pinctrl-single,pins = <
+ 0x14 (PIN_OUTPUT | MUX_MODE2) /* fref_clk0_out.sys_drm_msecure */
+ >;
+ };
+};
+
+&omap4_pmx_core {
+ twl6030_pins: pinmux_twl6030_pins {
+ pinctrl-single,pins = <
+ 0x15e (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1.sys_nirq1 */
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/vf610-cosmic.dts b/arch/arm/boot/dts/vf610-cosmic.dts
new file mode 100644
index 0000000..c42e4f9
--- /dev/null
+++ b/arch/arm/boot/dts/vf610-cosmic.dts
@@ -0,0 +1,47 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ * Copyright 2013 Linaro Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+/dts-v1/;
+#include "vf610.dtsi"
+
+/ {
+ model = "PHYTEC Cosmic/Cosmic+ Board";
+ compatible = "phytec,vf610-cosmic", "fsl,vf610";
+
+ chosen {
+ bootargs = "console=ttyLP1,115200";
+ };
+
+ memory {
+ reg = <0x80000000 0x10000000>;
+ };
+
+ clocks {
+ enet_ext {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <50000000>;
+ };
+ };
+
+};
+
+&fec1 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1_1>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_1>;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/vf610-twr.dts b/arch/arm/boot/dts/vf610-twr.dts
index 1a58678..c8047ca 100644
--- a/arch/arm/boot/dts/vf610-twr.dts
+++ b/arch/arm/boot/dts/vf610-twr.dts
@@ -36,6 +36,23 @@
};
+&dspi0 {
+ bus-num = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dspi0_1>;
+ status = "okay";
+
+ sflash: at26df081a@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "atmel,at26df081a";
+ spi-max-frequency = <16000000>;
+ spi-cpol;
+ spi-cpha;
+ reg = <0>;
+ };
+};
+
&fec0 {
phy-mode = "rmii";
pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/vf610.dtsi b/arch/arm/boot/dts/vf610.dtsi
index 67d929c..d31ce1b 100644
--- a/arch/arm/boot/dts/vf610.dtsi
+++ b/arch/arm/boot/dts/vf610.dtsi
@@ -123,6 +123,18 @@
status = "disabled";
};
+ dspi0: dspi0@4002c000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,vf610-dspi";
+ reg = <0x4002c000 0x1000>;
+ interrupts = <0 67 0x04>;
+ clocks = <&clks VF610_CLK_DSPI0>;
+ clock-names = "dspi";
+ spi-num-chipselects = <5>;
+ status = "disabled";
+ };
+
sai2: sai@40031000 {
compatible = "fsl,vf610-sai";
reg = <0x40031000 0x1000>;
diff --git a/arch/arm/boot/install.sh b/arch/arm/boot/install.sh
index 06ea7d4..2a45092 100644
--- a/arch/arm/boot/install.sh
+++ b/arch/arm/boot/install.sh
@@ -20,6 +20,20 @@
# $4 - default install path (blank if root directory)
#
+verify () {
+ if [ ! -f "$1" ]; then
+ echo "" 1>&2
+ echo " *** Missing file: $1" 1>&2
+ echo ' *** You need to run "make" before "make install".' 1>&2
+ echo "" 1>&2
+ exit 1
+ fi
+}
+
+# Make sure the files actually exist
+verify "$2"
+verify "$3"
+
# User may have a custom install script
if [ -x ~/bin/${INSTALLKERNEL} ]; then exec ~/bin/${INSTALLKERNEL} "$@"; fi
if [ -x /sbin/${INSTALLKERNEL} ]; then exec /sbin/${INSTALLKERNEL} "$@"; fi
diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig
index 254cf05..98a50c3 100644
--- a/arch/arm/configs/omap2plus_defconfig
+++ b/arch/arm/configs/omap2plus_defconfig
@@ -1,14 +1,13 @@
-CONFIG_EXPERIMENTAL=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=16
CONFIG_BLK_DEV_INITRD=y
CONFIG_EXPERT=y
-# CONFIG_SYSCTL_SYSCALL is not set
-CONFIG_KALLSYMS_EXTRA_PASS=y
CONFIG_SLAB=y
CONFIG_PROFILING=y
CONFIG_OPROFILE=y
@@ -20,22 +19,21 @@
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
# CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
CONFIG_ARCH_MULTI_V6=y
-CONFIG_ARCH_OMAP2PLUS=y
+CONFIG_OMAP_RESET_CLOCKS=y
+CONFIG_OMAP_MUX_DEBUG=y
CONFIG_ARCH_OMAP2=y
CONFIG_ARCH_OMAP3=y
CONFIG_ARCH_OMAP4=y
+CONFIG_SOC_OMAP5=y
CONFIG_SOC_AM33XX=y
-CONFIG_OMAP_RESET_CLOCKS=y
-CONFIG_OMAP_MUX_DEBUG=y
-CONFIG_ARCH_VEXPRESS_CA9X4=y
+CONFIG_SOC_DRA7XX=y
CONFIG_ARM_THUMBEE=y
CONFIG_ARM_ERRATA_411920=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
CONFIG_SMP=y
CONFIG_NR_CPUS=2
-CONFIG_LEDS=y
+CONFIG_CMA=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_ARM_APPENDED_DTB=y
@@ -61,8 +59,6 @@
# CONFIG_IPV6 is not set
CONFIG_NETFILTER=y
CONFIG_CAN=m
-CONFIG_CAN_RAW=m
-CONFIG_CAN_BCM=m
CONFIG_CAN_C_CAN=m
CONFIG_CAN_C_CAN_PLATFORM=m
CONFIG_BT=m
@@ -77,14 +73,13 @@
CONFIG_MAC80211_RC_PID=y
CONFIG_MAC80211_RC_DEFAULT_PID=y
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_CMA=y
-CONFIG_DMA_CMA=y
-CONFIG_CONNECTOR=y
CONFIG_DEVTMPFS=y
CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_DMA_CMA=y
+CONFIG_OMAP_OCP2SCP=y
+CONFIG_CONNECTOR=y
CONFIG_MTD=y
CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_OOPS=y
CONFIG_MTD_CFI=y
@@ -98,32 +93,40 @@
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=16384
-CONFIG_SENSORS_LIS3LV02D=m
CONFIG_SENSORS_TSL2550=m
-CONFIG_SENSORS_LIS3_I2C=m
CONFIG_BMP085_I2C=m
+CONFIG_SENSORS_LIS3_I2C=m
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_SCAN_ASYNC=y
CONFIG_MD=y
CONFIG_NETDEVICES=y
-CONFIG_SMSC_PHY=y
-CONFIG_NET_ETHERNET=y
-CONFIG_SMC91X=y
-CONFIG_SMSC911X=y
CONFIG_KS8851=y
CONFIG_KS8851_MLL=y
-CONFIG_LIBERTAS=m
-CONFIG_LIBERTAS_USB=m
-CONFIG_LIBERTAS_SDIO=m
-CONFIG_LIBERTAS_DEBUG=y
+CONFIG_SMC91X=y
+CONFIG_SMSC911X=y
+CONFIG_TI_CPSW=y
+CONFIG_AT803X_PHY=y
+CONFIG_SMSC_PHY=y
CONFIG_USB_USBNET=y
CONFIG_USB_NET_SMSC95XX=y
CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
CONFIG_USB_EPSON2888=y
CONFIG_USB_KC2190=y
+CONFIG_LIBERTAS=m
+CONFIG_LIBERTAS_USB=m
+CONFIG_LIBERTAS_SDIO=m
+CONFIG_LIBERTAS_DEBUG=y
+CONFIG_WL_TI=y
+CONFIG_WL12XX=m
+CONFIG_WL18XX=m
+CONFIG_WLCORE_SPI=m
+CONFIG_WLCORE_SDIO=m
+CONFIG_MWIFIEX=m
+CONFIG_MWIFIEX_SDIO=m
+CONFIG_MWIFIEX_USB=m
CONFIG_INPUT_JOYDEV=y
CONFIG_INPUT_EVDEV=y
CONFIG_KEYBOARD_GPIO=y
@@ -133,7 +136,6 @@
CONFIG_TOUCHSCREEN_ADS7846=y
CONFIG_INPUT_MISC=y
CONFIG_INPUT_TWL4030_PWRBUTTON=y
-CONFIG_VT_HW_CONSOLE_BINDING=y
# CONFIG_LEGACY_PTYS is not set
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
@@ -143,8 +145,7 @@
CONFIG_SERIAL_8250_SHARE_IRQ=y
CONFIG_SERIAL_8250_DETECT_IRQ=y
CONFIG_SERIAL_8250_RSA=y
-CONFIG_SERIAL_AMBA_PL011=y
-CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+CONFIG_SERIAL_OF_PLATFORM=y
CONFIG_SERIAL_OMAP=y
CONFIG_SERIAL_OMAP_CONSOLE=y
CONFIG_HW_RANDOM=y
@@ -158,31 +159,31 @@
CONFIG_W1=y
CONFIG_POWER_SUPPLY=y
CONFIG_SENSORS_LM75=m
-CONFIG_WATCHDOG=y
CONFIG_THERMAL=y
-CONFIG_THERMAL_HWMON=y
-CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
CONFIG_THERMAL_GOV_FAIR_SHARE=y
-CONFIG_THERMAL_GOV_STEP_WISE=y
CONFIG_THERMAL_GOV_USER_SPACE=y
-CONFIG_CPU_THERMAL=y
+CONFIG_TI_SOC_THERMAL=y
+CONFIG_OMAP4_THERMAL=y
+CONFIG_OMAP5_THERMAL=y
+CONFIG_DRA752_THERMAL=y
+CONFIG_WATCHDOG=y
CONFIG_OMAP_WATCHDOG=y
CONFIG_TWL4030_WATCHDOG=y
+CONFIG_MFD_PALMAS=y
CONFIG_MFD_TPS65217=y
CONFIG_MFD_TPS65910=y
CONFIG_TWL6040_CORE=y
-CONFIG_REGULATOR_TWL4030=y
+CONFIG_REGULATOR_PALMAS=y
CONFIG_REGULATOR_TPS65023=y
CONFIG_REGULATOR_TPS6507X=y
CONFIG_REGULATOR_TPS65217=y
CONFIG_REGULATOR_TPS65910=y
+CONFIG_REGULATOR_TWL4030=y
CONFIG_FB=y
CONFIG_FIRMWARE_EDID=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
-CONFIG_FB_OMAP_LCD_VGA=y
CONFIG_OMAP2_DSS=m
-CONFIG_OMAP2_DSS_RFBI=y
CONFIG_OMAP2_DSS_SDI=y
CONFIG_OMAP2_DSS_DSI=y
CONFIG_FB_OMAP2=m
@@ -194,12 +195,8 @@
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=y
CONFIG_LCD_PLATFORM=y
-CONFIG_DISPLAY_SUPPORT=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
-CONFIG_FONTS=y
-CONFIG_FONT_8x8=y
-CONFIG_FONT_8x16=y
CONFIG_LOGO=y
CONFIG_SOUND=m
CONFIG_SND=m
@@ -216,14 +213,14 @@
CONFIG_USB=y
CONFIG_USB_DEBUG=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-CONFIG_USB_DEVICEFS=y
CONFIG_USB_MON=y
CONFIG_USB_WDM=y
CONFIG_USB_STORAGE=y
-CONFIG_USB_LIBUSUAL=y
+CONFIG_USB_DWC3=m
CONFIG_USB_TEST=y
-CONFIG_USB_PHY=y
CONFIG_NOP_USB_XCEIV=y
+CONFIG_OMAP_USB2=y
+CONFIG_OMAP_USB3=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_DEBUG=y
CONFIG_USB_GADGET_DEBUG_FILES=y
@@ -232,7 +229,6 @@
CONFIG_MMC=y
CONFIG_MMC_UNSAFE_RESUME=y
CONFIG_SDIO_UART=y
-CONFIG_MMC_ARMMMCI=y
CONFIG_MMC_OMAP=y
CONFIG_MMC_OMAP_HS=y
CONFIG_NEW_LEDS=y
@@ -252,11 +248,8 @@
CONFIG_DMADEVICES=y
CONFIG_TI_EDMA=y
CONFIG_DMA_OMAP=y
-CONFIG_TI_SOC_THERMAL=y
-CONFIG_TI_THERMAL=y
-CONFIG_OMAP4_THERMAL=y
-CONFIG_OMAP5_THERMAL=y
-CONFIG_DRA752_THERMAL=y
+CONFIG_EXTCON=y
+CONFIG_EXTCON_PALMAS=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
@@ -275,23 +268,18 @@
CONFIG_UBIFS_FS=y
CONFIG_CRAMFS=y
CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
CONFIG_ROOT_NFS=y
-CONFIG_PARTITION_ADVANCED=y
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_INFO=y
CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
CONFIG_SCHEDSTATS=y
CONFIG_TIMER_STATS=y
CONFIG_PROVE_LOCKING=y
-CONFIG_DEBUG_SPINLOCK_SLEEP=y
# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_DEBUG_INFO=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
CONFIG_SECURITY=y
CONFIG_CRYPTO_MICHAEL_MIC=y
# CONFIG_CRYPTO_ANSI_CPRNG is not set
@@ -300,9 +288,6 @@
CONFIG_CRC_ITU_T=y
CONFIG_CRC7=y
CONFIG_LIBCRC32C=y
-CONFIG_SOC_OMAP5=y
-CONFIG_TI_DAVINCI_MDIO=y
-CONFIG_TI_DAVINCI_CPDMA=y
-CONFIG_TI_CPSW=y
-CONFIG_AT803X_PHY=y
-CONFIG_SOC_DRA7XX=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
diff --git a/arch/arm/configs/u8500_defconfig b/arch/arm/configs/u8500_defconfig
index a0025dc..ac632cc 100644
--- a/arch/arm/configs/u8500_defconfig
+++ b/arch/arm/configs/u8500_defconfig
@@ -1,4 +1,3 @@
-CONFIG_HIGHMEM=y
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_NO_HZ=y
@@ -16,6 +15,9 @@
CONFIG_NR_CPUS=2
CONFIG_PREEMPT=y
CONFIG_AEABI=y
+CONFIG_HIGHMEM=y
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_ARM_ATAG_DTB_COMPAT=y
CONFIG_CMDLINE="root=/dev/ram0 console=ttyAMA2,115200n8"
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y
@@ -68,8 +70,8 @@
CONFIG_WATCHDOG=y
CONFIG_MFD_STMPE=y
CONFIG_MFD_TC3589X=y
-CONFIG_REGULATOR_GPIO=y
CONFIG_REGULATOR_AB8500=y
+CONFIG_REGULATOR_GPIO=y
CONFIG_SOUND=y
CONFIG_SND=y
CONFIG_SND_SOC=y
@@ -78,10 +80,8 @@
CONFIG_USB=y
CONFIG_USB_MUSB_HDRC=y
CONFIG_USB_MUSB_UX500=y
-CONFIG_USB_PHY=y
CONFIG_AB8500_USB=y
CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_MUSB_HDRC=y
CONFIG_USB_ETH=m
CONFIG_MMC=y
CONFIG_MMC_UNSAFE_RESUME=y
@@ -116,12 +116,12 @@
CONFIG_ROOT_NFS=y
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
-CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_INFO=y
CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
CONFIG_DEBUG_KERNEL=y
# CONFIG_SCHED_DEBUG is not set
# CONFIG_DEBUG_PREEMPT is not set
-CONFIG_DEBUG_INFO=y
# CONFIG_FTRACE is not set
CONFIG_DEBUG_USER=y
CONFIG_CRYPTO_DEV_UX500=y
diff --git a/arch/arm/include/asm/jump_label.h b/arch/arm/include/asm/jump_label.h
index bfc198c..863c892 100644
--- a/arch/arm/include/asm/jump_label.h
+++ b/arch/arm/include/asm/jump_label.h
@@ -16,7 +16,7 @@
static __always_inline bool arch_static_branch(struct static_key *key)
{
- asm goto("1:\n\t"
+ asm_volatile_goto("1:\n\t"
JUMP_LABEL_NOP "\n\t"
".pushsection __jump_table, \"aw\"\n\t"
".word 1b, %l[l_yes], %c0\n\t"
diff --git a/arch/arm/mach-at91/at91sam9n12.c b/arch/arm/mach-at91/at91sam9n12.c
index c7d670d..2d895a2 100644
--- a/arch/arm/mach-at91/at91sam9n12.c
+++ b/arch/arm/mach-at91/at91sam9n12.c
@@ -169,6 +169,7 @@
CLKDEV_CON_DEV_ID("t0_clk", "f8008000.timer", &tcb_clk),
CLKDEV_CON_DEV_ID("t0_clk", "f800c000.timer", &tcb_clk),
CLKDEV_CON_DEV_ID("mci_clk", "f0008000.mmc", &mmc_clk),
+ CLKDEV_CON_DEV_ID(NULL, "f0010000.ssc", &ssc_clk),
CLKDEV_CON_DEV_ID("dma_clk", "ffffec00.dma-controller", &dma_clk),
CLKDEV_CON_DEV_ID(NULL, "f8010000.i2c", &twi0_clk),
CLKDEV_CON_DEV_ID(NULL, "f8014000.i2c", &twi1_clk),
diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c
index 82d3ad8..f087b5f 100644
--- a/arch/arm/mach-kirkwood/board-dt.c
+++ b/arch/arm/mach-kirkwood/board-dt.c
@@ -92,7 +92,6 @@
writel(readl(CPU_CONFIG) & ~CPU_CONFIG_ERROR_PROP, CPU_CONFIG);
BUG_ON(mvebu_mbus_dt_init());
- kirkwood_setup_wins();
kirkwood_l2_init();
diff --git a/arch/arm/mach-mxs/mach-mxs.c b/arch/arm/mach-mxs/mach-mxs.c
index 98f6e2a..c0ceb17 100644
--- a/arch/arm/mach-mxs/mach-mxs.c
+++ b/arch/arm/mach-mxs/mach-mxs.c
@@ -332,6 +332,11 @@
update_fec_mac_prop(OUI_CRYSTALFONTZ);
}
+static void __init m28cu3_init(void)
+{
+ update_fec_mac_prop(OUI_DENX);
+}
+
static const char __init *mxs_get_soc_id(void)
{
struct device_node *np;
@@ -459,6 +464,8 @@
apx4devkit_init();
else if (of_machine_is_compatible("crystalfontz,cfa10036"))
crystalfontz_init();
+ else if (of_machine_is_compatible("msr,m28cu3"))
+ m28cu3_init();
of_platform_populate(NULL, of_default_bus_match_table,
NULL, parent);
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index b5fb5f7..68c9688 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -94,6 +94,7 @@
select GENERIC_CLOCKEVENTS
select GENERIC_IRQ_CHIP
select HAVE_CLK
+ select MACH_OMAP_GENERIC
select OMAP_DM_TIMER
select PINCTRL
select PROC_DEVICETREE if PROC_FS
@@ -187,16 +188,11 @@
config OMAP_PACKAGE_CBP
bool
-comment "OMAP Board Type"
+comment "OMAP Legacy Platform Data Board Type"
depends on ARCH_OMAP2PLUS
config MACH_OMAP_GENERIC
- bool "Generic OMAP2+ board"
- depends on ARCH_OMAP2PLUS
- default y
- help
- Support for generic TI OMAP2+ boards using Flattened Device Tree.
- More information at Documentation/devicetree
+ bool
config MACH_OMAP2_TUSB6010
bool
@@ -260,12 +256,6 @@
default y
select OMAP_PACKAGE_CBB
-config MACH_OMAP3EVM
- bool "OMAP 3530 EVM board"
- depends on ARCH_OMAP3
- default y
- select OMAP_PACKAGE_CBB
-
config MACH_OMAP3517EVM
bool "OMAP3517/ AM3517 EVM board"
depends on ARCH_OMAP3
@@ -314,33 +304,12 @@
select MACH_NOKIA_N810_WIMAX
select OMAP_PACKAGE_ZAC
-config MACH_NOKIA_RM680
- bool "Nokia N950 (RM-680) / N9 (RM-696) phones"
- depends on ARCH_OMAP3
- default y
- select MACH_NOKIA_RM696
- select OMAP_PACKAGE_CBB
-
config MACH_NOKIA_RX51
bool "Nokia N900 (RX-51) phone"
depends on ARCH_OMAP3
default y
select OMAP_PACKAGE_CBB
-config MACH_OMAP_ZOOM2
- bool "OMAP3 Zoom2 board"
- depends on ARCH_OMAP3
- default y
- select OMAP_PACKAGE_CBB
- select REGULATOR_FIXED_VOLTAGE if REGULATOR
-
-config MACH_OMAP_ZOOM3
- bool "OMAP3630 Zoom3 board"
- depends on ARCH_OMAP3
- default y
- select OMAP_PACKAGE_CBP
- select REGULATOR_FIXED_VOLTAGE if REGULATOR
-
config MACH_CM_T35
bool "CompuLab CM-T35/CM-T3730 modules"
depends on ARCH_OMAP3
@@ -357,31 +326,12 @@
config MACH_CM_T3730
bool
-config MACH_IGEP0020
- bool "IGEP v2 board"
- depends on ARCH_OMAP3
- default y
- select OMAP_PACKAGE_CBB
-
-config MACH_IGEP0030
- bool "IGEP OMAP3 module"
- depends on ARCH_OMAP3
- default y
- select MACH_IGEP0020
- select OMAP_PACKAGE_CBB
-
config MACH_SBC3530
bool "OMAP3 SBC STALKER board"
depends on ARCH_OMAP3
default y
select OMAP_PACKAGE_CUS
-config MACH_OMAP_3630SDP
- bool "OMAP3630 SDP board"
- depends on ARCH_OMAP3
- default y
- select OMAP_PACKAGE_CBP
-
config MACH_TI8168EVM
bool "TI8168 Evaluation Module"
depends on SOC_TI81XX
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index afb457c..096d6bb 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -233,7 +233,7 @@
endif
# Specific board support
-obj-$(CONFIG_MACH_OMAP_GENERIC) += board-generic.o
+obj-$(CONFIG_MACH_OMAP_GENERIC) += board-generic.o pdata-quirks.o
obj-$(CONFIG_MACH_OMAP_H4) += board-h4.o
obj-$(CONFIG_MACH_OMAP_2430SDP) += board-2430sdp.o
obj-$(CONFIG_MACH_OMAP3_BEAGLE) += board-omap3beagle.o
@@ -242,26 +242,14 @@
obj-$(CONFIG_MACH_OMAP3530_LV_SOM) += board-omap3logic.o
obj-$(CONFIG_MACH_OMAP3_TORPEDO) += board-omap3logic.o
obj-$(CONFIG_MACH_OVERO) += board-overo.o
-obj-$(CONFIG_MACH_OMAP3EVM) += board-omap3evm.o
obj-$(CONFIG_MACH_OMAP3_PANDORA) += board-omap3pandora.o
obj-$(CONFIG_MACH_OMAP_3430SDP) += board-3430sdp.o
obj-$(CONFIG_MACH_NOKIA_N8X0) += board-n8x0.o
-obj-$(CONFIG_MACH_NOKIA_RM680) += board-rm680.o sdram-nokia.o
obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51.o sdram-nokia.o
obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51-peripherals.o
obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51-video.o
-obj-$(CONFIG_MACH_OMAP_ZOOM2) += board-zoom.o board-zoom-peripherals.o
-obj-$(CONFIG_MACH_OMAP_ZOOM2) += board-zoom-display.o
-obj-$(CONFIG_MACH_OMAP_ZOOM2) += board-zoom-debugboard.o
-obj-$(CONFIG_MACH_OMAP_ZOOM3) += board-zoom.o board-zoom-peripherals.o
-obj-$(CONFIG_MACH_OMAP_ZOOM3) += board-zoom-display.o
-obj-$(CONFIG_MACH_OMAP_ZOOM3) += board-zoom-debugboard.o
-obj-$(CONFIG_MACH_OMAP_3630SDP) += board-3630sdp.o
-obj-$(CONFIG_MACH_OMAP_3630SDP) += board-zoom-peripherals.o
-obj-$(CONFIG_MACH_OMAP_3630SDP) += board-zoom-display.o
obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o
obj-$(CONFIG_MACH_CM_T3517) += board-cm-t3517.o
-obj-$(CONFIG_MACH_IGEP0020) += board-igep0020.o
obj-$(CONFIG_MACH_TOUCHBOOK) += board-omap3touchbook.o
obj-$(CONFIG_MACH_OMAP3517EVM) += board-am3517evm.o
diff --git a/arch/arm/mach-omap2/board-3630sdp.c b/arch/arm/mach-omap2/board-3630sdp.c
deleted file mode 100644
index 20d6d81..0000000
--- a/arch/arm/mach-omap2/board-3630sdp.c
+++ /dev/null
@@ -1,225 +0,0 @@
-/*
- * Copyright (C) 2009 Texas Instruments Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/input.h>
-#include <linux/gpio.h>
-#include <linux/mtd/nand.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include "common.h"
-#include "gpmc-smc91x.h"
-
-#include "board-zoom.h"
-
-#include "board-flash.h"
-#include "mux.h"
-#include "sdram-hynix-h8mbx00u0mer-0em.h"
-
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
-
-static struct omap_smc91x_platform_data board_smc91x_data = {
- .cs = 3,
- .flags = GPMC_MUX_ADD_DATA | IORESOURCE_IRQ_LOWLEVEL,
-};
-
-static void __init board_smc91x_init(void)
-{
- board_smc91x_data.gpio_irq = 158;
- gpmc_smc91x_init(&board_smc91x_data);
-}
-
-#else
-
-static inline void board_smc91x_init(void)
-{
-}
-
-#endif /* defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) */
-
-static void enable_board_wakeup_source(void)
-{
- /* T2 interrupt line (keypad) */
- omap_mux_init_signal("sys_nirq",
- OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
-}
-
-static struct usbhs_phy_data phy_data[] __initdata = {
- {
- .port = 1,
- .reset_gpio = 126,
- .vcc_gpio = -EINVAL,
- },
- {
- .port = 2,
- .reset_gpio = 61,
- .vcc_gpio = -EINVAL,
- },
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-
- .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
- { .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-/*
- * SDP3630 CS organization
- * See also the Switch S8 settings in the comments.
- */
-static char chip_sel_sdp[][GPMC_CS_NUM] = {
- {PDC_NOR, PDC_NAND, PDC_ONENAND, DBG_MPDB, 0, 0, 0, 0}, /* S8:1111 */
- {PDC_ONENAND, PDC_NAND, PDC_NOR, DBG_MPDB, 0, 0, 0, 0}, /* S8:1110 */
- {PDC_NAND, PDC_ONENAND, PDC_NOR, DBG_MPDB, 0, 0, 0, 0}, /* S8:1101 */
-};
-
-static struct mtd_partition sdp_nor_partitions[] = {
- /* bootloader (U-Boot, etc) in first sector */
- {
- .name = "Bootloader-NOR",
- .offset = 0,
- .size = SZ_256K,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- /* bootloader params in the next sector */
- {
- .name = "Params-NOR",
- .offset = MTDPART_OFS_APPEND,
- .size = SZ_256K,
- .mask_flags = 0,
- },
- /* kernel */
- {
- .name = "Kernel-NOR",
- .offset = MTDPART_OFS_APPEND,
- .size = SZ_2M,
- .mask_flags = 0
- },
- /* file system */
- {
- .name = "Filesystem-NOR",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL,
- .mask_flags = 0
- }
-};
-
-static struct mtd_partition sdp_onenand_partitions[] = {
- {
- .name = "X-Loader-OneNAND",
- .offset = 0,
- .size = 4 * (64 * 2048),
- .mask_flags = MTD_WRITEABLE /* force read-only */
- },
- {
- .name = "U-Boot-OneNAND",
- .offset = MTDPART_OFS_APPEND,
- .size = 2 * (64 * 2048),
- .mask_flags = MTD_WRITEABLE /* force read-only */
- },
- {
- .name = "U-Boot Environment-OneNAND",
- .offset = MTDPART_OFS_APPEND,
- .size = 1 * (64 * 2048),
- },
- {
- .name = "Kernel-OneNAND",
- .offset = MTDPART_OFS_APPEND,
- .size = 16 * (64 * 2048),
- },
- {
- .name = "File System-OneNAND",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static struct mtd_partition sdp_nand_partitions[] = {
- /* All the partition sizes are listed in terms of NAND block size */
- {
- .name = "X-Loader-NAND",
- .offset = 0,
- .size = 4 * (64 * 2048),
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "U-Boot-NAND",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
- .size = 10 * (64 * 2048),
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "Boot Env-NAND",
-
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x1c0000 */
- .size = 6 * (64 * 2048),
- },
- {
- .name = "Kernel-NAND",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
- .size = 40 * (64 * 2048),
- },
- {
- .name = "File System - NAND",
- .size = MTDPART_SIZ_FULL,
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x780000 */
- },
-};
-
-static struct flash_partitions sdp_flash_partitions[] = {
- {
- .parts = sdp_nor_partitions,
- .nr_parts = ARRAY_SIZE(sdp_nor_partitions),
- },
- {
- .parts = sdp_onenand_partitions,
- .nr_parts = ARRAY_SIZE(sdp_onenand_partitions),
- },
- {
- .parts = sdp_nand_partitions,
- .nr_parts = ARRAY_SIZE(sdp_nand_partitions),
- },
-};
-
-static void __init omap_sdp_init(void)
-{
- omap3_mux_init(board_mux, OMAP_PACKAGE_CBP);
- zoom_peripherals_init();
- omap_sdrc_init(h8mbx00u0mer0em_sdrc_params,
- h8mbx00u0mer0em_sdrc_params);
- zoom_display_init();
- board_smc91x_init();
- board_flash_init(sdp_flash_partitions, chip_sel_sdp, NAND_BUSWIDTH_16);
- enable_board_wakeup_source();
-
- usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
- usbhs_init(&usbhs_bdata);
-}
-
-MACHINE_START(OMAP_3630SDP, "OMAP 3630SDP board")
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap3630_init_early,
- .init_irq = omap3_init_irq,
- .handle_irq = omap3_intc_handle_irq,
- .init_machine = omap_sdp_init,
- .init_late = omap3630_init_late,
- .init_time = omap3_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c
index 39c7838..19f1652 100644
--- a/arch/arm/mach-omap2/board-generic.c
+++ b/arch/arm/mach-omap2/board-generic.c
@@ -15,13 +15,10 @@
#include <linux/of_irq.h>
#include <linux/of_platform.h>
#include <linux/irqdomain.h>
-#include <linux/clk.h>
#include <asm/mach/arch.h>
#include "common.h"
-#include "common-board-devices.h"
-#include "dss-common.h"
#if !(defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3))
#define intc_of_init NULL
@@ -36,40 +33,9 @@
{ }
};
-/*
- * Create alias for USB host PHY clock.
- * Remove this when clock phandle can be provided via DT
- */
-static void __init legacy_init_ehci_clk(char *clkname)
-{
- int ret;
-
- ret = clk_add_alias("main_clk", NULL, clkname, NULL);
- if (ret) {
- pr_err("%s:Failed to add main_clk alias to %s :%d\n",
- __func__, clkname, ret);
- }
-}
-
static void __init omap_generic_init(void)
{
- omap_sdrc_init(NULL, NULL);
-
- of_platform_populate(NULL, omap_dt_match_table, NULL, NULL);
-
- /*
- * HACK: call display setup code for selected boards to enable omapdss.
- * This will be removed when omapdss supports DT.
- */
- if (of_machine_is_compatible("ti,omap4-panda")) {
- omap4_panda_display_init_of();
- legacy_init_ehci_clk("auxclk3_ck");
-
- }
- else if (of_machine_is_compatible("ti,omap4-sdp"))
- omap_4430sdp_display_init_of();
- else if (of_machine_is_compatible("ti,omap5-uevm"))
- legacy_init_ehci_clk("auxclk1_ck");
+ pdata_quirks_init(omap_dt_match_table);
}
#ifdef CONFIG_SOC_OMAP2420
@@ -129,6 +95,24 @@
.restart = omap3xxx_restart,
MACHINE_END
+static const char *omap36xx_boards_compat[] __initdata = {
+ "ti,omap36xx",
+ NULL,
+};
+
+DT_MACHINE_START(OMAP36XX_DT, "Generic OMAP36xx (Flattened Device Tree)")
+ .reserve = omap_reserve,
+ .map_io = omap3_map_io,
+ .init_early = omap3630_init_early,
+ .init_irq = omap_intc_of_init,
+ .handle_irq = omap3_intc_handle_irq,
+ .init_machine = omap_generic_init,
+ .init_late = omap3_init_late,
+ .init_time = omap3_sync32k_timer_init,
+ .dt_compat = omap36xx_boards_compat,
+ .restart = omap3xxx_restart,
+MACHINE_END
+
static const char *omap3_gp_boards_compat[] __initdata = {
"ti,omap3-beagle",
"timll,omap3-devkit8000",
@@ -162,6 +146,7 @@
.init_irq = omap_intc_of_init,
.handle_irq = omap3_intc_handle_irq,
.init_machine = omap_generic_init,
+ .init_late = am33xx_init_late,
.init_time = omap3_gptimer_timer_init,
.dt_compat = am33xx_boards_compat,
.restart = am33xx_restart,
@@ -201,6 +186,7 @@
.init_early = omap5_init_early,
.init_irq = omap_gic_of_init,
.init_machine = omap_generic_init,
+ .init_late = omap5_init_late,
.init_time = omap5_realtime_timer_init,
.dt_compat = omap5_boards_compat,
.restart = omap44xx_restart,
@@ -216,6 +202,7 @@
DT_MACHINE_START(AM43_DT, "Generic AM43 (Flattened Device Tree)")
.map_io = am33xx_map_io,
.init_early = am43xx_init_early,
+ .init_late = am43xx_init_late,
.init_irq = omap_gic_of_init,
.init_machine = omap_generic_init,
.init_time = omap3_sync32k_timer_init,
@@ -234,6 +221,7 @@
.smp = smp_ops(omap4_smp_ops),
.map_io = omap5_map_io,
.init_early = dra7xx_init_early,
+ .init_late = dra7xx_init_late,
.init_irq = omap_gic_of_init,
.init_machine = omap_generic_init,
.init_time = omap5_realtime_timer_init,
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
deleted file mode 100644
index 06dbb2d..0000000
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ /dev/null
@@ -1,718 +0,0 @@
-/*
- * Copyright (C) 2009 Integration Software and Electronic Engineering.
- *
- * Modified from mach-omap2/board-generic.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/gpio.h>
-#include <linux/interrupt.h>
-#include <linux/input.h>
-#include <linux/usb/phy.h>
-
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-#include <linux/i2c/twl.h>
-#include <linux/mmc/host.h>
-
-#include <linux/mtd/nand.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-#include <linux/platform_data/mtd-onenand-omap2.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "sdram-numonyx-m65kxxxxam.h"
-#include "common-board-devices.h"
-#include "board-flash.h"
-#include "control.h"
-#include "gpmc-onenand.h"
-
-#define IGEP2_SMSC911X_CS 5
-#define IGEP2_SMSC911X_GPIO 176
-#define IGEP2_GPIO_USBH_NRESET 24
-#define IGEP2_GPIO_LED0_GREEN 26
-#define IGEP2_GPIO_LED0_RED 27
-#define IGEP2_GPIO_LED1_RED 28
-#define IGEP2_GPIO_DVI_PUP 170
-
-#define IGEP2_RB_GPIO_WIFI_NPD 94
-#define IGEP2_RB_GPIO_WIFI_NRESET 95
-#define IGEP2_RB_GPIO_BT_NRESET 137
-#define IGEP2_RC_GPIO_WIFI_NPD 138
-#define IGEP2_RC_GPIO_WIFI_NRESET 139
-#define IGEP2_RC_GPIO_BT_NRESET 137
-
-#define IGEP3_GPIO_LED0_GREEN 54
-#define IGEP3_GPIO_LED0_RED 53
-#define IGEP3_GPIO_LED1_RED 16
-#define IGEP3_GPIO_USBH_NRESET 183
-
-#define IGEP_SYSBOOT_MASK 0x1f
-#define IGEP_SYSBOOT_NAND 0x0f
-#define IGEP_SYSBOOT_ONENAND 0x10
-
-/*
- * IGEP2 Hardware Revision Table
- *
- * --------------------------------------------------------------------------
- * | Id. | Hw Rev. | HW0 (28) | WIFI_NPD | WIFI_NRESET | BT_NRESET |
- * --------------------------------------------------------------------------
- * | 0 | B | high | gpio94 | gpio95 | - |
- * | 0 | B/C (B-compatible) | high | gpio94 | gpio95 | gpio137 |
- * | 1 | C | low | gpio138 | gpio139 | gpio137 |
- * --------------------------------------------------------------------------
- */
-
-#define IGEP2_BOARD_HWREV_B 0
-#define IGEP2_BOARD_HWREV_C 1
-#define IGEP3_BOARD_HWREV 2
-
-static u8 hwrev;
-
-static void __init igep2_get_revision(void)
-{
- u8 ret;
-
- if (machine_is_igep0030()) {
- hwrev = IGEP3_BOARD_HWREV;
- return;
- }
-
- omap_mux_init_gpio(IGEP2_GPIO_LED1_RED, OMAP_PIN_INPUT);
-
- if (gpio_request_one(IGEP2_GPIO_LED1_RED, GPIOF_IN, "GPIO_HW0_REV")) {
- pr_warning("IGEP2: Could not obtain gpio GPIO_HW0_REV\n");
- pr_err("IGEP2: Unknown Hardware Revision\n");
- return;
- }
-
- ret = gpio_get_value(IGEP2_GPIO_LED1_RED);
- if (ret == 0) {
- pr_info("IGEP2: Hardware Revision C (B-NON compatible)\n");
- hwrev = IGEP2_BOARD_HWREV_C;
- } else if (ret == 1) {
- pr_info("IGEP2: Hardware Revision B/C (B compatible)\n");
- hwrev = IGEP2_BOARD_HWREV_B;
- } else {
- pr_err("IGEP2: Unknown Hardware Revision\n");
- hwrev = -1;
- }
-
- gpio_free(IGEP2_GPIO_LED1_RED);
-}
-
-#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
- defined(CONFIG_MTD_ONENAND_OMAP2_MODULE) || \
- defined(CONFIG_MTD_NAND_OMAP2) || \
- defined(CONFIG_MTD_NAND_OMAP2_MODULE)
-
-#define ONENAND_MAP 0x20000000
-
-/* NAND04GR4E1A ( x2 Flash built-in COMBO POP MEMORY )
- * Since the device is equipped with two DataRAMs, and two-plane NAND
- * Flash memory array, these two component enables simultaneous program
- * of 4KiB. Plane1 has only even blocks such as block0, block2, block4
- * while Plane2 has only odd blocks such as block1, block3, block5.
- * So MTD regards it as 4KiB page size and 256KiB block size 64*(2*2048)
- */
-
-static struct mtd_partition igep_flash_partitions[] = {
- {
- .name = "X-Loader",
- .offset = 0,
- .size = 2 * (64*(2*2048))
- },
- {
- .name = "U-Boot",
- .offset = MTDPART_OFS_APPEND,
- .size = 6 * (64*(2*2048)),
- },
- {
- .name = "Environment",
- .offset = MTDPART_OFS_APPEND,
- .size = 2 * (64*(2*2048)),
- },
- {
- .name = "Kernel",
- .offset = MTDPART_OFS_APPEND,
- .size = 12 * (64*(2*2048)),
- },
- {
- .name = "File System",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static inline u32 igep_get_sysboot_value(void)
-{
- return omap_ctrl_readl(OMAP343X_CONTROL_STATUS) & IGEP_SYSBOOT_MASK;
-}
-
-static void __init igep_flash_init(void)
-{
- u32 mux;
- mux = igep_get_sysboot_value();
-
- if (mux == IGEP_SYSBOOT_NAND) {
- pr_info("IGEP: initializing NAND memory device\n");
- board_nand_init(igep_flash_partitions,
- ARRAY_SIZE(igep_flash_partitions),
- 0, NAND_BUSWIDTH_16, nand_default_timings);
- } else if (mux == IGEP_SYSBOOT_ONENAND) {
- pr_info("IGEP: initializing OneNAND memory device\n");
- board_onenand_init(igep_flash_partitions,
- ARRAY_SIZE(igep_flash_partitions), 0);
- } else {
- pr_err("IGEP: Flash: unsupported sysboot sequence found\n");
- }
-}
-
-#else
-static void __init igep_flash_init(void) {}
-#endif
-
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
-
-#include <linux/smsc911x.h>
-#include "gpmc-smsc911x.h"
-
-static struct omap_smsc911x_platform_data smsc911x_cfg = {
- .cs = IGEP2_SMSC911X_CS,
- .gpio_irq = IGEP2_SMSC911X_GPIO,
- .gpio_reset = -EINVAL,
- .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
-};
-
-static inline void __init igep2_init_smsc911x(void)
-{
- gpmc_smsc911x_init(&smsc911x_cfg);
-}
-
-#else
-static inline void __init igep2_init_smsc911x(void) { }
-#endif
-
-static struct regulator_consumer_supply igep_vmmc1_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
-static struct regulator_init_data igep_vmmc1 = {
- .constraints = {
- .min_uV = 1850000,
- .max_uV = 3150000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(igep_vmmc1_supply),
- .consumer_supplies = igep_vmmc1_supply,
-};
-
-static struct regulator_consumer_supply igep_vio_supply[] = {
- REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.1"),
-};
-
-static struct regulator_init_data igep_vio = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .apply_uV = 1,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(igep_vio_supply),
- .consumer_supplies = igep_vio_supply,
-};
-
-static struct regulator_consumer_supply igep_vmmc2_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
-};
-
-static struct regulator_init_data igep_vmmc2 = {
- .constraints = {
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .always_on = 1,
- },
- .num_consumer_supplies = ARRAY_SIZE(igep_vmmc2_supply),
- .consumer_supplies = igep_vmmc2_supply,
-};
-
-static struct fixed_voltage_config igep_vwlan = {
- .supply_name = "vwlan",
- .microvolts = 3300000,
- .gpio = -EINVAL,
- .enabled_at_boot = 1,
- .init_data = &igep_vmmc2,
-};
-
-static struct platform_device igep_vwlan_device = {
- .name = "reg-fixed-voltage",
- .id = 0,
- .dev = {
- .platform_data = &igep_vwlan,
- },
-};
-
-static struct omap2_hsmmc_info mmc[] = {
- {
- .mmc = 1,
- .caps = MMC_CAP_4_BIT_DATA,
- .gpio_cd = -EINVAL,
- .gpio_wp = -EINVAL,
- .deferred = true,
- },
-#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
- {
- .mmc = 2,
- .caps = MMC_CAP_4_BIT_DATA,
- .gpio_cd = -EINVAL,
- .gpio_wp = -EINVAL,
- },
-#endif
- {} /* Terminator */
-};
-
-#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
-#include <linux/leds.h>
-
-static struct gpio_led igep_gpio_leds[] = {
- [0] = {
- .name = "omap3:red:user0",
- .default_state = 0,
- },
- [1] = {
- .name = "omap3:green:boot",
- .default_state = 1,
- },
- [2] = {
- .name = "omap3:red:user1",
- .default_state = 0,
- },
- [3] = {
- .name = "omap3:green:user1",
- .default_state = 0,
- .gpio = -EINVAL, /* gets replaced */
- .active_low = 1,
- },
-};
-
-static struct gpio_led_platform_data igep_led_pdata = {
- .leds = igep_gpio_leds,
- .num_leds = ARRAY_SIZE(igep_gpio_leds),
-};
-
-static struct platform_device igep_led_device = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &igep_led_pdata,
- },
-};
-
-static void __init igep_leds_init(void)
-{
- if (machine_is_igep0020()) {
- igep_gpio_leds[0].gpio = IGEP2_GPIO_LED0_RED;
- igep_gpio_leds[1].gpio = IGEP2_GPIO_LED0_GREEN;
- igep_gpio_leds[2].gpio = IGEP2_GPIO_LED1_RED;
- } else {
- igep_gpio_leds[0].gpio = IGEP3_GPIO_LED0_RED;
- igep_gpio_leds[1].gpio = IGEP3_GPIO_LED0_GREEN;
- igep_gpio_leds[2].gpio = IGEP3_GPIO_LED1_RED;
- }
-
- platform_device_register(&igep_led_device);
-}
-
-#else
-static struct gpio igep_gpio_leds[] __initdata = {
- { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:red:d0" },
- { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:green:d0" },
- { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:red:d1" },
-};
-
-static inline void igep_leds_init(void)
-{
- int i;
-
- if (machine_is_igep0020()) {
- igep_gpio_leds[0].gpio = IGEP2_GPIO_LED0_RED;
- igep_gpio_leds[1].gpio = IGEP2_GPIO_LED0_GREEN;
- igep_gpio_leds[2].gpio = IGEP2_GPIO_LED1_RED;
- } else {
- igep_gpio_leds[0].gpio = IGEP3_GPIO_LED0_RED;
- igep_gpio_leds[1].gpio = IGEP3_GPIO_LED0_GREEN;
- igep_gpio_leds[2].gpio = IGEP3_GPIO_LED1_RED;
- }
-
- if (gpio_request_array(igep_gpio_leds, ARRAY_SIZE(igep_gpio_leds))) {
- pr_warning("IGEP v2: Could not obtain leds gpios\n");
- return;
- }
-
- for (i = 0; i < ARRAY_SIZE(igep_gpio_leds); i++)
- gpio_export(igep_gpio_leds[i].gpio, 0);
-}
-#endif
-
-static struct gpio igep2_twl_gpios[] = {
- { -EINVAL, GPIOF_IN, "GPIO_EHCI_NOC" },
- { -EINVAL, GPIOF_OUT_INIT_LOW, "GPIO_USBH_CPEN" },
-};
-
-static int igep_twl_gpio_setup(struct device *dev,
- unsigned gpio, unsigned ngpio)
-{
- int ret;
-
- /* gpio + 0 is "mmc0_cd" (input/IRQ) */
- mmc[0].gpio_cd = gpio + 0;
- omap_hsmmc_late_init(mmc);
-
- /* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
-#if !defined(CONFIG_LEDS_GPIO) && !defined(CONFIG_LEDS_GPIO_MODULE)
- ret = gpio_request_one(gpio + TWL4030_GPIO_MAX + 1, GPIOF_OUT_INIT_HIGH,
- "gpio-led:green:d1");
- if (ret == 0)
- gpio_export(gpio + TWL4030_GPIO_MAX + 1, 0);
- else
- pr_warning("IGEP: Could not obtain gpio GPIO_LED1_GREEN\n");
-#else
- igep_gpio_leds[3].gpio = gpio + TWL4030_GPIO_MAX + 1;
-#endif
-
- if (machine_is_igep0030())
- return 0;
-
- /*
- * REVISIT: need ehci-omap hooks for external VBUS
- * power switch and overcurrent detect
- */
- igep2_twl_gpios[0].gpio = gpio + 1;
-
- /* TWL4030_GPIO_MAX + 0 == ledA, GPIO_USBH_CPEN (out, active low) */
- igep2_twl_gpios[1].gpio = gpio + TWL4030_GPIO_MAX;
-
- ret = gpio_request_array(igep2_twl_gpios, ARRAY_SIZE(igep2_twl_gpios));
- if (ret < 0)
- pr_err("IGEP2: Could not obtain gpio for USBH_CPEN");
-
- return 0;
-};
-
-static struct twl4030_gpio_platform_data igep_twl4030_gpio_pdata = {
- .use_leds = true,
- .setup = igep_twl_gpio_setup,
-};
-
-static struct connector_dvi_platform_data omap3stalker_dvi_connector_pdata = {
- .name = "dvi",
- .source = "tfp410.0",
- .i2c_bus_num = 3,
-};
-
-static struct platform_device omap3stalker_dvi_connector_device = {
- .name = "connector-dvi",
- .id = 0,
- .dev.platform_data = &omap3stalker_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data omap3stalker_tfp410_pdata = {
- .name = "tfp410.0",
- .source = "dpi.0",
- .data_lines = 24,
- .power_down_gpio = IGEP2_GPIO_DVI_PUP,
-};
-
-static struct platform_device omap3stalker_tfp410_device = {
- .name = "tfp410",
- .id = 0,
- .dev.platform_data = &omap3stalker_tfp410_pdata,
-};
-
-static struct omap_dss_board_info igep2_dss_data = {
- .default_display_name = "dvi",
-};
-
-static struct platform_device *igep_devices[] __initdata = {
- &igep_vwlan_device,
- &omap3stalker_tfp410_device,
- &omap3stalker_dvi_connector_device,
-};
-
-static int igep2_keymap[] = {
- KEY(0, 0, KEY_LEFT),
- KEY(0, 1, KEY_RIGHT),
- KEY(0, 2, KEY_A),
- KEY(0, 3, KEY_B),
- KEY(1, 0, KEY_DOWN),
- KEY(1, 1, KEY_UP),
- KEY(1, 2, KEY_E),
- KEY(1, 3, KEY_F),
- KEY(2, 0, KEY_ENTER),
- KEY(2, 1, KEY_I),
- KEY(2, 2, KEY_J),
- KEY(2, 3, KEY_K),
- KEY(3, 0, KEY_M),
- KEY(3, 1, KEY_N),
- KEY(3, 2, KEY_O),
- KEY(3, 3, KEY_P)
-};
-
-static struct matrix_keymap_data igep2_keymap_data = {
- .keymap = igep2_keymap,
- .keymap_size = ARRAY_SIZE(igep2_keymap),
-};
-
-static struct twl4030_keypad_data igep2_keypad_pdata = {
- .keymap_data = &igep2_keymap_data,
- .rows = 4,
- .cols = 4,
- .rep = 1,
-};
-
-static struct twl4030_platform_data igep_twldata = {
- /* platform_data for children goes here */
- .gpio = &igep_twl4030_gpio_pdata,
- .vmmc1 = &igep_vmmc1,
- .vio = &igep_vio,
-};
-
-static struct i2c_board_info __initdata igep2_i2c3_boardinfo[] = {
- {
- I2C_BOARD_INFO("eeprom", 0x50),
- },
-};
-
-static void __init igep_i2c_init(void)
-{
- int ret;
-
- omap3_pmic_get_config(&igep_twldata, TWL_COMMON_PDATA_USB,
- TWL_COMMON_REGULATOR_VPLL2);
- igep_twldata.vpll2->constraints.apply_uV = true;
- igep_twldata.vpll2->constraints.name = "VDVI";
-
- if (machine_is_igep0020()) {
- /*
- * Bus 3 is attached to the DVI port where devices like the
- * pico DLP projector don't work reliably with 400kHz
- */
- ret = omap_register_i2c_bus(3, 100, igep2_i2c3_boardinfo,
- ARRAY_SIZE(igep2_i2c3_boardinfo));
- if (ret)
- pr_warning("IGEP2: Could not register I2C3 bus (%d)\n", ret);
-
- igep_twldata.keypad = &igep2_keypad_pdata;
- /* Get common pmic data */
- omap3_pmic_get_config(&igep_twldata, TWL_COMMON_PDATA_AUDIO, 0);
- }
-
- omap3_pmic_init("twl4030", &igep_twldata);
-}
-
-static struct usbhs_phy_data igep2_phy_data[] __initdata = {
- {
- .port = 1,
- .reset_gpio = IGEP2_GPIO_USBH_NRESET,
- .vcc_gpio = -EINVAL,
- },
-};
-
-static struct usbhs_phy_data igep3_phy_data[] __initdata = {
- {
- .port = 2,
- .reset_gpio = IGEP3_GPIO_USBH_NRESET,
- .vcc_gpio = -EINVAL,
- },
-};
-
-static struct usbhs_omap_platform_data igep2_usbhs_bdata __initdata = {
- .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-static struct usbhs_omap_platform_data igep3_usbhs_bdata __initdata = {
- .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
- /* Display Sub System */
- OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA9, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA10, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA11, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA12, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA13, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA14, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA15, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA20, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- /* TFP410 PanelBus DVI Transmitte (GPIO_170) */
- OMAP3_MUX(HDQ_SIO, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
- /* SMSC9221 LAN Controller ETH IRQ (GPIO_176) */
- OMAP3_MUX(MCSPI1_CS2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
- { .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
-static struct gpio igep_wlan_bt_gpios[] __initdata = {
- { -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_WIFI_NPD" },
- { -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_WIFI_NRESET" },
- { -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_BT_NRESET" },
-};
-
-static void __init igep_wlan_bt_init(void)
-{
- int err;
-
- /* GPIO's for WLAN-BT combo depends on hardware revision */
- if (hwrev == IGEP2_BOARD_HWREV_B) {
- igep_wlan_bt_gpios[0].gpio = IGEP2_RB_GPIO_WIFI_NPD;
- igep_wlan_bt_gpios[1].gpio = IGEP2_RB_GPIO_WIFI_NRESET;
- igep_wlan_bt_gpios[2].gpio = IGEP2_RB_GPIO_BT_NRESET;
- } else if (hwrev == IGEP2_BOARD_HWREV_C || machine_is_igep0030()) {
- igep_wlan_bt_gpios[0].gpio = IGEP2_RC_GPIO_WIFI_NPD;
- igep_wlan_bt_gpios[1].gpio = IGEP2_RC_GPIO_WIFI_NRESET;
- igep_wlan_bt_gpios[2].gpio = IGEP2_RC_GPIO_BT_NRESET;
- } else
- return;
-
- /* Make sure that the GPIO pins are muxed correctly */
- omap_mux_init_gpio(igep_wlan_bt_gpios[0].gpio, OMAP_PIN_OUTPUT);
- omap_mux_init_gpio(igep_wlan_bt_gpios[1].gpio, OMAP_PIN_OUTPUT);
- omap_mux_init_gpio(igep_wlan_bt_gpios[2].gpio, OMAP_PIN_OUTPUT);
-
- err = gpio_request_array(igep_wlan_bt_gpios,
- ARRAY_SIZE(igep_wlan_bt_gpios));
- if (err) {
- pr_warning("IGEP2: Could not obtain WIFI/BT gpios\n");
- return;
- }
-
- gpio_export(igep_wlan_bt_gpios[0].gpio, 0);
- gpio_export(igep_wlan_bt_gpios[1].gpio, 0);
- gpio_export(igep_wlan_bt_gpios[2].gpio, 0);
-
- gpio_set_value(igep_wlan_bt_gpios[1].gpio, 0);
- udelay(10);
- gpio_set_value(igep_wlan_bt_gpios[1].gpio, 1);
-
-}
-#else
-static inline void __init igep_wlan_bt_init(void) { }
-#endif
-
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
- REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-static void __init igep_init(void)
-{
- regulator_register_fixed(1, dummy_supplies, ARRAY_SIZE(dummy_supplies));
- omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
-
- /* Get IGEP2 hardware revision */
- igep2_get_revision();
-
- omap_hsmmc_init(mmc);
-
- /* Register I2C busses and drivers */
- igep_i2c_init();
- platform_add_devices(igep_devices, ARRAY_SIZE(igep_devices));
- omap_serial_init();
- omap_sdrc_init(m65kxxxxam_sdrc_params,
- m65kxxxxam_sdrc_params);
- usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
- usb_musb_init(NULL);
-
- igep_flash_init();
- igep_leds_init();
- omap_twl4030_audio_init("igep2", NULL);
-
- /*
- * WLAN-BT combo module from MuRata which has a Marvell WLAN
- * (88W8686) + CSR Bluetooth chipset. Uses SDIO interface.
- */
- igep_wlan_bt_init();
-
- if (machine_is_igep0020()) {
- omap_display_init(&igep2_dss_data);
- igep2_init_smsc911x();
- usbhs_init_phys(igep2_phy_data, ARRAY_SIZE(igep2_phy_data));
- usbhs_init(&igep2_usbhs_bdata);
- } else {
- usbhs_init_phys(igep3_phy_data, ARRAY_SIZE(igep3_phy_data));
- usbhs_init(&igep3_usbhs_bdata);
- }
-}
-
-MACHINE_START(IGEP0020, "IGEP v2 board")
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap35xx_init_early,
- .init_irq = omap3_init_irq,
- .handle_irq = omap3_intc_handle_irq,
- .init_machine = igep_init,
- .init_late = omap35xx_init_late,
- .init_time = omap3_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
-
-MACHINE_START(IGEP0030, "IGEP OMAP3 module")
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap35xx_init_early,
- .init_irq = omap3_init_irq,
- .handle_irq = omap3_intc_handle_irq,
- .init_machine = igep_init,
- .init_late = omap35xx_init_late,
- .init_time = omap3_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c
index dd8da2c..4ec8d82 100644
--- a/arch/arm/mach-omap2/board-ldp.c
+++ b/arch/arm/mach-omap2/board-ldp.c
@@ -36,7 +36,6 @@
#include <asm/mach/map.h>
#include "common.h"
-#include "board-zoom.h"
#include "gpmc.h"
#include "gpmc-smsc911x.h"
@@ -406,7 +405,7 @@
usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
usb_musb_init(NULL);
board_nand_init(ldp_nand_partitions, ARRAY_SIZE(ldp_nand_partitions),
- ZOOM_NAND_CS, 0, nand_default_timings);
+ 0, 0, nand_default_timings);
omap_hsmmc_init(mmc);
ldp_display_init();
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
deleted file mode 100644
index 1814387..0000000
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ /dev/null
@@ -1,756 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-omap3evm.c
- *
- * Copyright (C) 2008 Texas Instruments
- *
- * Modified from mach-omap2/board-3430sdp.c
- *
- * Initial code: Syed Mohammed Khasim
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/leds.h>
-#include <linux/interrupt.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/nand.h>
-
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
-#include <linux/i2c/twl.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/musb.h>
-#include <linux/usb/usb_phy_gen_xceiv.h>
-#include <linux/smsc911x.h>
-
-#include <linux/wl12xx.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <linux/mmc/host.h>
-#include <linux/export.h>
-#include <linux/usb/phy.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <linux/platform_data/mtd-nand-omap2.h>
-#include "common.h"
-#include <linux/platform_data/spi-omap2-mcspi.h>
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include "soc.h"
-#include "mux.h"
-#include "sdram-micron-mt46h32m32lf-6.h"
-#include "hsmmc.h"
-#include "common-board-devices.h"
-#include "board-flash.h"
-
-#define NAND_CS 0
-
-#define OMAP3_EVM_TS_GPIO 175
-#define OMAP3_EVM_EHCI_VBUS 22
-#define OMAP3_EVM_EHCI_SELECT 61
-
-#define OMAP3EVM_ETHR_START 0x2c000000
-#define OMAP3EVM_ETHR_SIZE 1024
-#define OMAP3EVM_ETHR_ID_REV 0x50
-#define OMAP3EVM_ETHR_GPIO_IRQ 176
-#define OMAP3EVM_SMSC911X_CS 5
-/*
- * Eth Reset signal
- * 64 = Generation 1 (<=RevD)
- * 7 = Generation 2 (>=RevE)
- */
-#define OMAP3EVM_GEN1_ETHR_GPIO_RST 64
-#define OMAP3EVM_GEN2_ETHR_GPIO_RST 7
-
-/*
- * OMAP35x EVM revision
- * Run time detection of EVM revision is done by reading Ethernet
- * PHY ID -
- * GEN_1 = 0x01150000
- * GEN_2 = 0x92200000
- */
-enum {
- OMAP3EVM_BOARD_GEN_1 = 0, /* EVM Rev between A - D */
- OMAP3EVM_BOARD_GEN_2, /* EVM Rev >= Rev E */
-};
-
-static u8 omap3_evm_version;
-
-static u8 get_omap3_evm_rev(void)
-{
- return omap3_evm_version;
-}
-
-static void __init omap3_evm_get_revision(void)
-{
- void __iomem *ioaddr;
- unsigned int smsc_id;
-
- /* Ethernet PHY ID is stored at ID_REV register */
- ioaddr = ioremap_nocache(OMAP3EVM_ETHR_START, SZ_1K);
- if (!ioaddr)
- return;
- smsc_id = readl(ioaddr + OMAP3EVM_ETHR_ID_REV) & 0xFFFF0000;
- iounmap(ioaddr);
-
- switch (smsc_id) {
- /*SMSC9115 chipset*/
- case 0x01150000:
- omap3_evm_version = OMAP3EVM_BOARD_GEN_1;
- break;
- /*SMSC 9220 chipset*/
- case 0x92200000:
- default:
- omap3_evm_version = OMAP3EVM_BOARD_GEN_2;
- }
-}
-
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
-#include "gpmc-smsc911x.h"
-
-static struct omap_smsc911x_platform_data smsc911x_cfg = {
- .cs = OMAP3EVM_SMSC911X_CS,
- .gpio_irq = OMAP3EVM_ETHR_GPIO_IRQ,
- .gpio_reset = -EINVAL,
- .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
-};
-
-static inline void __init omap3evm_init_smsc911x(void)
-{
- /* Configure ethernet controller reset gpio */
- if (cpu_is_omap3430()) {
- if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1)
- smsc911x_cfg.gpio_reset = OMAP3EVM_GEN1_ETHR_GPIO_RST;
- else
- smsc911x_cfg.gpio_reset = OMAP3EVM_GEN2_ETHR_GPIO_RST;
- }
-
- gpmc_smsc911x_init(&smsc911x_cfg);
-}
-
-#else
-static inline void __init omap3evm_init_smsc911x(void) { return; }
-#endif
-
-/*
- * OMAP3EVM LCD Panel control signals
- */
-#define OMAP3EVM_LCD_PANEL_LR 2
-#define OMAP3EVM_LCD_PANEL_UD 3
-#define OMAP3EVM_LCD_PANEL_INI 152
-#define OMAP3EVM_LCD_PANEL_QVGA 154
-#define OMAP3EVM_LCD_PANEL_RESB 155
-
-#define OMAP3EVM_LCD_PANEL_ENVDD 153
-#define OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO 210
-
-/*
- * OMAP3EVM DVI control signals
- */
-#define OMAP3EVM_DVI_PANEL_EN_GPIO 199
-
-#ifdef CONFIG_BROKEN
-static void __init omap3_evm_display_init(void)
-{
- int r;
-
- r = gpio_request_one(OMAP3EVM_LCD_PANEL_ENVDD, GPIOF_OUT_INIT_LOW,
- "lcd_panel_envdd");
- if (r)
- pr_err("failed to get lcd_panel_envdd GPIO\n");
-
- r = gpio_request_one(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO,
- GPIOF_OUT_INIT_LOW, "lcd_panel_bklight");
- if (r)
- pr_err("failed to get lcd_panel_bklight GPIO\n");
-
- if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
- gpio_set_value_cansleep(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 0);
- else
- gpio_set_value_cansleep(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 1);
-}
-#endif
-
-static struct panel_sharp_ls037v7dw01_platform_data omap3_evm_lcd_pdata = {
- .name = "lcd",
- .source = "dpi.0",
-
- .data_lines = 18,
-
- .resb_gpio = OMAP3EVM_LCD_PANEL_RESB,
- .ini_gpio = OMAP3EVM_LCD_PANEL_INI,
- .mo_gpio = OMAP3EVM_LCD_PANEL_QVGA,
- .lr_gpio = OMAP3EVM_LCD_PANEL_LR,
- .ud_gpio = OMAP3EVM_LCD_PANEL_UD,
-};
-
-static struct platform_device omap3_evm_lcd_device = {
- .name = "panel-sharp-ls037v7dw01",
- .id = 0,
- .dev.platform_data = &omap3_evm_lcd_pdata,
-};
-
-static struct connector_dvi_platform_data omap3_evm_dvi_connector_pdata = {
- .name = "dvi",
- .source = "tfp410.0",
- .i2c_bus_num = -1,
-};
-
-static struct platform_device omap3_evm_dvi_connector_device = {
- .name = "connector-dvi",
- .id = 0,
- .dev.platform_data = &omap3_evm_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data omap3_evm_tfp410_pdata = {
- .name = "tfp410.0",
- .source = "dpi.0",
- .data_lines = 24,
- .power_down_gpio = OMAP3EVM_DVI_PANEL_EN_GPIO,
-};
-
-static struct platform_device omap3_evm_tfp410_device = {
- .name = "tfp410",
- .id = 0,
- .dev.platform_data = &omap3_evm_tfp410_pdata,
-};
-
-static struct connector_atv_platform_data omap3_evm_tv_pdata = {
- .name = "tv",
- .source = "venc.0",
- .connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
- .invert_polarity = false,
-};
-
-static struct platform_device omap3_evm_tv_connector_device = {
- .name = "connector-analog-tv",
- .id = 0,
- .dev.platform_data = &omap3_evm_tv_pdata,
-};
-
-static struct omap_dss_board_info omap3_evm_dss_data = {
- .default_display_name = "lcd",
-};
-
-static struct regulator_consumer_supply omap3evm_vmmc1_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply omap3evm_vsim_supply[] = {
- REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data omap3evm_vmmc1 = {
- .constraints = {
- .min_uV = 1850000,
- .max_uV = 3150000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap3evm_vmmc1_supply),
- .consumer_supplies = omap3evm_vmmc1_supply,
-};
-
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data omap3evm_vsim = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 3000000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap3evm_vsim_supply),
- .consumer_supplies = omap3evm_vsim_supply,
-};
-
-static struct omap2_hsmmc_info mmc[] = {
- {
- .mmc = 1,
- .caps = MMC_CAP_4_BIT_DATA,
- .gpio_cd = -EINVAL,
- .gpio_wp = 63,
- .deferred = true,
- },
-#ifdef CONFIG_WILINK_PLATFORM_DATA
- {
- .name = "wl1271",
- .mmc = 2,
- .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_POWER_OFF_CARD,
- .gpio_wp = -EINVAL,
- .gpio_cd = -EINVAL,
- .nonremovable = true,
- },
-#endif
- {} /* Terminator */
-};
-
-static struct gpio_led gpio_leds[] = {
- {
- .name = "omap3evm::ledb",
- /* normally not visible (board underside) */
- .default_trigger = "default-on",
- .gpio = -EINVAL, /* gets replaced */
- .active_low = true,
- },
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
- .leds = gpio_leds,
- .num_leds = ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &gpio_led_info,
- },
-};
-
-
-static int omap3evm_twl_gpio_setup(struct device *dev,
- unsigned gpio, unsigned ngpio)
-{
- int r, lcd_bl_en;
-
- /* gpio + 0 is "mmc0_cd" (input/IRQ) */
- mmc[0].gpio_cd = gpio + 0;
- omap_hsmmc_late_init(mmc);
-
- /*
- * Most GPIOs are for USB OTG. Some are mostly sent to
- * the P2 connector; notably LEDA for the LCD backlight.
- */
-
- /* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */
- lcd_bl_en = get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2 ?
- GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW;
- r = gpio_request_one(gpio + TWL4030_GPIO_MAX, lcd_bl_en, "EN_LCD_BKL");
- if (r)
- printk(KERN_ERR "failed to get/set lcd_bkl gpio\n");
-
- /* gpio + 7 == DVI Enable */
- gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
-
- /* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
- gpio_leds[0].gpio = gpio + TWL4030_GPIO_MAX + 1;
-
- platform_device_register(&leds_gpio);
-
- /* Enable VBUS switch by setting TWL4030.GPIO2DIR as output
- * for starting USB tranceiver
- */
-#ifdef CONFIG_TWL4030_CORE
- if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) {
- u8 val;
-
- twl_i2c_read_u8(TWL4030_MODULE_GPIO, &val, REG_GPIODATADIR1);
- val |= 0x04; /* TWL4030.GPIO2DIR BIT at GPIODATADIR1(0x9B) */
- twl_i2c_write_u8(TWL4030_MODULE_GPIO, val, REG_GPIODATADIR1);
- }
-#endif
-
- return 0;
-}
-
-static struct twl4030_gpio_platform_data omap3evm_gpio_data = {
- .use_leds = true,
- .setup = omap3evm_twl_gpio_setup,
-};
-
-static uint32_t board_keymap[] = {
- KEY(0, 0, KEY_LEFT),
- KEY(0, 1, KEY_DOWN),
- KEY(0, 2, KEY_ENTER),
- KEY(0, 3, KEY_M),
-
- KEY(1, 0, KEY_RIGHT),
- KEY(1, 1, KEY_UP),
- KEY(1, 2, KEY_I),
- KEY(1, 3, KEY_N),
-
- KEY(2, 0, KEY_A),
- KEY(2, 1, KEY_E),
- KEY(2, 2, KEY_J),
- KEY(2, 3, KEY_O),
-
- KEY(3, 0, KEY_B),
- KEY(3, 1, KEY_F),
- KEY(3, 2, KEY_K),
- KEY(3, 3, KEY_P)
-};
-
-static struct matrix_keymap_data board_map_data = {
- .keymap = board_keymap,
- .keymap_size = ARRAY_SIZE(board_keymap),
-};
-
-static struct twl4030_keypad_data omap3evm_kp_data = {
- .keymap_data = &board_map_data,
- .rows = 4,
- .cols = 4,
- .rep = 1,
-};
-
-/* ads7846 on SPI */
-static struct regulator_consumer_supply omap3evm_vio_supply[] = {
- REGULATOR_SUPPLY("vcc", "spi1.0"),
-};
-
-/* VIO for ads7846 */
-static struct regulator_init_data omap3evm_vio = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap3evm_vio_supply),
- .consumer_supplies = omap3evm_vio_supply,
-};
-
-#ifdef CONFIG_WILINK_PLATFORM_DATA
-
-#define OMAP3EVM_WLAN_PMENA_GPIO (150)
-#define OMAP3EVM_WLAN_IRQ_GPIO (149)
-
-static struct regulator_consumer_supply omap3evm_vmmc2_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
-};
-
-/* VMMC2 for driving the WL12xx module */
-static struct regulator_init_data omap3evm_vmmc2 = {
- .constraints = {
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap3evm_vmmc2_supply),
- .consumer_supplies = omap3evm_vmmc2_supply,
-};
-
-static struct fixed_voltage_config omap3evm_vwlan = {
- .supply_name = "vwl1271",
- .microvolts = 1800000, /* 1.80V */
- .gpio = OMAP3EVM_WLAN_PMENA_GPIO,
- .startup_delay = 70000, /* 70ms */
- .enable_high = 1,
- .enabled_at_boot = 0,
- .init_data = &omap3evm_vmmc2,
-};
-
-static struct platform_device omap3evm_wlan_regulator = {
- .name = "reg-fixed-voltage",
- .id = 1,
- .dev = {
- .platform_data = &omap3evm_vwlan,
- },
-};
-
-struct wl12xx_platform_data omap3evm_wlan_data __initdata = {
- .board_ref_clock = WL12XX_REFCLOCK_38, /* 38.4 MHz */
-};
-#endif
-
-/* VAUX2 for USB */
-static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = {
- REGULATOR_SUPPLY("VDD_CSIPHY1", "omap3isp"), /* OMAP ISP */
- REGULATOR_SUPPLY("VDD_CSIPHY2", "omap3isp"), /* OMAP ISP */
- REGULATOR_SUPPLY("vcc", "usb_phy_gen_xceiv.2"), /* hsusb port 2 */
- REGULATOR_SUPPLY("vaux2", NULL),
-};
-
-static struct regulator_init_data omap3evm_vaux2 = {
- .constraints = {
- .min_uV = 2800000,
- .max_uV = 2800000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap3evm_vaux2_supplies),
- .consumer_supplies = omap3evm_vaux2_supplies,
-};
-
-static struct twl4030_platform_data omap3evm_twldata = {
- /* platform_data for children goes here */
- .keypad = &omap3evm_kp_data,
- .gpio = &omap3evm_gpio_data,
- .vio = &omap3evm_vio,
- .vmmc1 = &omap3evm_vmmc1,
- .vsim = &omap3evm_vsim,
-};
-
-static int __init omap3_evm_i2c_init(void)
-{
- omap3_pmic_get_config(&omap3evm_twldata,
- TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
- TWL_COMMON_PDATA_AUDIO,
- TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
-
- omap3evm_twldata.vdac->constraints.apply_uV = true;
- omap3evm_twldata.vpll2->constraints.apply_uV = true;
-
- omap3_pmic_init("twl4030", &omap3evm_twldata);
- omap_register_i2c_bus(2, 400, NULL, 0);
- omap_register_i2c_bus(3, 400, NULL, 0);
- return 0;
-}
-
-static struct usbhs_phy_data phy_data[] __initdata = {
- {
- .port = 2,
- .reset_gpio = -1, /* set at runtime */
- .vcc_gpio = -EINVAL,
- },
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
- .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux omap35x_board_mux[] __initdata = {
- OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
- OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
- OMAP_PIN_OFF_WAKEUPENABLE),
- OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
- OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
- OMAP_PIN_OFF_WAKEUPENABLE),
- OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
- OMAP_PIN_OFF_NONE),
- OMAP3_MUX(GPMC_WAIT2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
- OMAP_PIN_OFF_NONE),
-#ifdef CONFIG_WILINK_PLATFORM_DATA
- /* WLAN IRQ - GPIO 149 */
- OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
-
- /* WLAN POWER ENABLE - GPIO 150 */
- OMAP3_MUX(UART1_CTS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-
- /* MMC2 SDIO pin muxes for WL12xx */
- OMAP3_MUX(SDMMC2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
- OMAP3_MUX(SDMMC2_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
- OMAP3_MUX(SDMMC2_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
- OMAP3_MUX(SDMMC2_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
- OMAP3_MUX(SDMMC2_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
- OMAP3_MUX(SDMMC2_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-#endif
- { .reg_offset = OMAP_MUX_TERMINATOR },
-};
-
-static struct omap_board_mux omap36x_board_mux[] __initdata = {
- OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
- OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
- OMAP_PIN_OFF_WAKEUPENABLE),
- OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
- OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
- OMAP_PIN_OFF_WAKEUPENABLE),
- /* AM/DM37x EVM: DSS data bus muxed with sys_boot */
- OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
- OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
- OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
- OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
- OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
- OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
- OMAP3_MUX(SYS_BOOT0, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
- OMAP3_MUX(SYS_BOOT1, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
- OMAP3_MUX(SYS_BOOT3, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
- OMAP3_MUX(SYS_BOOT4, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
- OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
- OMAP3_MUX(SYS_BOOT6, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
-#ifdef CONFIG_WILINK_PLATFORM_DATA
- /* WLAN IRQ - GPIO 149 */
- OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
-
- /* WLAN POWER ENABLE - GPIO 150 */
- OMAP3_MUX(UART1_CTS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-
- /* MMC2 SDIO pin muxes for WL12xx */
- OMAP3_MUX(SDMMC2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
- OMAP3_MUX(SDMMC2_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
- OMAP3_MUX(SDMMC2_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
- OMAP3_MUX(SDMMC2_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
- OMAP3_MUX(SDMMC2_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
- OMAP3_MUX(SDMMC2_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-#endif
-
- { .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#else
-#define omap35x_board_mux NULL
-#define omap36x_board_mux NULL
-#endif
-
-static struct omap_musb_board_data musb_board_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_OTG,
- .power = 100,
-};
-
-static struct gpio omap3_evm_ehci_gpios[] __initdata = {
- { OMAP3_EVM_EHCI_VBUS, GPIOF_OUT_INIT_HIGH, "enable EHCI VBUS" },
- { OMAP3_EVM_EHCI_SELECT, GPIOF_OUT_INIT_LOW, "select EHCI port" },
-};
-
-static void __init omap3_evm_wl12xx_init(void)
-{
-#ifdef CONFIG_WILINK_PLATFORM_DATA
- int ret;
-
- /* WL12xx WLAN Init */
- omap3evm_wlan_data.irq = gpio_to_irq(OMAP3EVM_WLAN_IRQ_GPIO);
- ret = wl12xx_set_platform_data(&omap3evm_wlan_data);
- if (ret)
- pr_err("error setting wl12xx data: %d\n", ret);
- ret = platform_device_register(&omap3evm_wlan_regulator);
- if (ret)
- pr_err("error registering wl12xx device: %d\n", ret);
-#endif
-}
-
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
- REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-static struct mtd_partition omap3evm_nand_partitions[] = {
- /* All the partition sizes are listed in terms of NAND block size */
- {
- .name = "X-Loader",
- .offset = 0,
- .size = 4*(SZ_128K),
- .mask_flags = MTD_WRITEABLE
- },
- {
- .name = "U-Boot",
- .offset = MTDPART_OFS_APPEND,
- .size = 14*(SZ_128K),
- .mask_flags = MTD_WRITEABLE
- },
- {
- .name = "U-Boot Env",
- .offset = MTDPART_OFS_APPEND,
- .size = 2*(SZ_128K)
- },
- {
- .name = "Kernel",
- .offset = MTDPART_OFS_APPEND,
- .size = 40*(SZ_128K)
- },
- {
- .name = "File system",
- .size = MTDPART_SIZ_FULL,
- .offset = MTDPART_OFS_APPEND,
- },
-};
-
-static void __init omap3_evm_init(void)
-{
- struct omap_board_mux *obm;
-
- omap3_evm_get_revision();
- regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-
- obm = (cpu_is_omap3630()) ? omap36x_board_mux : omap35x_board_mux;
- omap3_mux_init(obm, OMAP_PACKAGE_CBB);
-
- omap_mux_init_gpio(63, OMAP_PIN_INPUT);
- omap_hsmmc_init(mmc);
-
- if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
- omap3evm_twldata.vaux2 = &omap3evm_vaux2;
-
- omap3_evm_i2c_init();
-
- omap_display_init(&omap3_evm_dss_data);
- platform_device_register(&omap3_evm_lcd_device);
- platform_device_register(&omap3_evm_tfp410_device);
- platform_device_register(&omap3_evm_dvi_connector_device);
- platform_device_register(&omap3_evm_tv_connector_device);
-
- omap_serial_init();
- omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL);
-
- /* OMAP3EVM uses ISP1504 phy and so register nop transceiver */
- usb_nop_xceiv_register();
-
- if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) {
- /* enable EHCI VBUS using GPIO22 */
- omap_mux_init_gpio(OMAP3_EVM_EHCI_VBUS, OMAP_PIN_INPUT_PULLUP);
- /* Select EHCI port on main board */
- omap_mux_init_gpio(OMAP3_EVM_EHCI_SELECT,
- OMAP_PIN_INPUT_PULLUP);
- gpio_request_array(omap3_evm_ehci_gpios,
- ARRAY_SIZE(omap3_evm_ehci_gpios));
-
- /* setup EHCI phy reset config */
- omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
- phy_data[0].reset_gpio = 21;
-
- /* EVM REV >= E can supply 500mA with EXTVBUS programming */
- musb_board_data.power = 500;
- musb_board_data.extvbus = 1;
- } else {
- /* setup EHCI phy reset on MDC */
- omap_mux_init_gpio(135, OMAP_PIN_OUTPUT);
- phy_data[0].reset_gpio = 135;
- }
- usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
- usb_musb_init(&musb_board_data);
-
- usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
- usbhs_init(&usbhs_bdata);
- board_nand_init(omap3evm_nand_partitions,
- ARRAY_SIZE(omap3evm_nand_partitions), NAND_CS,
- NAND_BUSWIDTH_16, NULL);
-
- omap_ads7846_init(1, OMAP3_EVM_TS_GPIO, 310, NULL);
- omap3evm_init_smsc911x();
-#ifdef CONFIG_BROKEN
- omap3_evm_display_init();
-#endif
- omap3_evm_wl12xx_init();
- omap_twl4030_audio_init("omap3evm", NULL);
-}
-
-MACHINE_START(OMAP3EVM, "OMAP3 EVM")
- /* Maintainer: Syed Mohammed Khasim - Texas Instruments */
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap35xx_init_early,
- .init_irq = omap3_init_irq,
- .handle_irq = omap3_intc_handle_irq,
- .init_machine = omap3_evm_init,
- .init_late = omap35xx_init_late,
- .init_time = omap3_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-rm680.c b/arch/arm/mach-omap2/board-rm680.c
deleted file mode 100644
index 345e8c4..0000000
--- a/arch/arm/mach-omap2/board-rm680.c
+++ /dev/null
@@ -1,167 +0,0 @@
-/*
- * Board support file for Nokia N950 (RM-680) / N9 (RM-696).
- *
- * Copyright (C) 2010 Nokia
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/io.h>
-#include <linux/i2c.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/i2c/twl.h>
-#include <linux/platform_device.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/consumer.h>
-#include <linux/platform_data/mtd-onenand-omap2.h>
-#include <linux/usb/phy.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach-types.h>
-
-#include "common.h"
-#include "mux.h"
-#include "gpmc.h"
-#include "mmc.h"
-#include "hsmmc.h"
-#include "sdram-nokia.h"
-#include "common-board-devices.h"
-#include "gpmc-onenand.h"
-
-static struct regulator_consumer_supply rm680_vemmc_consumers[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
-};
-
-/* Fixed regulator for internal eMMC */
-static struct regulator_init_data rm680_vemmc = {
- .constraints = {
- .name = "rm680_vemmc",
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_STATUS
- | REGULATOR_CHANGE_MODE,
- },
- .num_consumer_supplies = ARRAY_SIZE(rm680_vemmc_consumers),
- .consumer_supplies = rm680_vemmc_consumers,
-};
-
-static struct fixed_voltage_config rm680_vemmc_config = {
- .supply_name = "VEMMC",
- .microvolts = 2900000,
- .gpio = 157,
- .startup_delay = 150,
- .enable_high = 1,
- .init_data = &rm680_vemmc,
-};
-
-static struct platform_device rm680_vemmc_device = {
- .name = "reg-fixed-voltage",
- .dev = {
- .platform_data = &rm680_vemmc_config,
- },
-};
-
-static struct platform_device *rm680_peripherals_devices[] __initdata = {
- &rm680_vemmc_device,
-};
-
-/* TWL */
-static struct twl4030_gpio_platform_data rm680_gpio_data = {
- .pullups = BIT(0),
- .pulldowns = BIT(1) | BIT(2) | BIT(8) | BIT(15),
-};
-
-static struct twl4030_platform_data rm680_twl_data = {
- .gpio = &rm680_gpio_data,
- /* add rest of the children here */
-};
-
-static void __init rm680_i2c_init(void)
-{
- omap3_pmic_get_config(&rm680_twl_data, TWL_COMMON_PDATA_USB, 0);
- omap_pmic_init(1, 2900, "twl5031", 7 + OMAP_INTC_START, &rm680_twl_data);
- omap_register_i2c_bus(2, 400, NULL, 0);
- omap_register_i2c_bus(3, 400, NULL, 0);
-}
-
-#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
- defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
-static struct omap_onenand_platform_data board_onenand_data[] = {
- {
- .gpio_irq = 65,
- .flags = ONENAND_SYNC_READWRITE,
- }
-};
-#endif
-
-/* eMMC */
-static struct omap2_hsmmc_info mmc[] __initdata = {
- {
- .name = "internal",
- .mmc = 2,
- .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_MMC_HIGHSPEED,
- .gpio_cd = -EINVAL,
- .gpio_wp = -EINVAL,
- },
- { /* Terminator */ }
-};
-
-static void __init rm680_peripherals_init(void)
-{
- platform_add_devices(rm680_peripherals_devices,
- ARRAY_SIZE(rm680_peripherals_devices));
- rm680_i2c_init();
- gpmc_onenand_init(board_onenand_data);
- omap_hsmmc_init(mmc);
-}
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
- { .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static void __init rm680_init(void)
-{
- struct omap_sdrc_params *sdrc_params;
-
- omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
- omap_serial_init();
-
- sdrc_params = nokia_get_sdram_timings();
- omap_sdrc_init(sdrc_params, sdrc_params);
-
- usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
- usb_musb_init(NULL);
- rm680_peripherals_init();
-}
-
-MACHINE_START(NOKIA_RM680, "Nokia RM-680 board")
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap3630_init_early,
- .init_irq = omap3_init_irq,
- .handle_irq = omap3_intc_handle_irq,
- .init_machine = rm680_init,
- .init_late = omap3630_init_late,
- .init_time = omap3_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
-
-MACHINE_START(NOKIA_RM696, "Nokia RM-696 board")
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap3630_init_early,
- .init_irq = omap3_init_irq,
- .handle_irq = omap3_intc_handle_irq,
- .init_machine = rm680_init,
- .init_late = omap3630_init_late,
- .init_time = omap3_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c
index c3270c0..f6fe388 100644
--- a/arch/arm/mach-omap2/board-rx51-peripherals.c
+++ b/arch/arm/mach-omap2/board-rx51-peripherals.c
@@ -167,38 +167,47 @@
.name = "lp5523:kb1",
.chan_nr = 0,
.led_current = 50,
+ .max_current = 100,
}, {
.name = "lp5523:kb2",
.chan_nr = 1,
.led_current = 50,
+ .max_current = 100,
}, {
.name = "lp5523:kb3",
.chan_nr = 2,
.led_current = 50,
+ .max_current = 100,
}, {
.name = "lp5523:kb4",
.chan_nr = 3,
.led_current = 50,
+ .max_current = 100,
}, {
.name = "lp5523:b",
.chan_nr = 4,
.led_current = 50,
+ .max_current = 100,
}, {
.name = "lp5523:g",
.chan_nr = 5,
.led_current = 50,
+ .max_current = 100,
}, {
.name = "lp5523:r",
.chan_nr = 6,
.led_current = 50,
+ .max_current = 100,
}, {
.name = "lp5523:kb5",
.chan_nr = 7,
.led_current = 50,
+ .max_current = 100,
}, {
.name = "lp5523:kb6",
.chan_nr = 8,
.led_current = 50,
+ .max_current = 100,
}
};
diff --git a/arch/arm/mach-omap2/board-zoom-debugboard.c b/arch/arm/mach-omap2/board-zoom-debugboard.c
deleted file mode 100644
index 42e5f23..0000000
--- a/arch/arm/mach-omap2/board-zoom-debugboard.c
+++ /dev/null
@@ -1,139 +0,0 @@
-/*
- * Copyright (C) 2009 Texas Instruments Inc.
- * Mikkel Christensen <mlc@ti.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/gpio.h>
-#include <linux/serial_8250.h>
-#include <linux/smsc911x.h>
-#include <linux/interrupt.h>
-
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-
-#include "gpmc.h"
-#include "gpmc-smsc911x.h"
-
-#include "board-zoom.h"
-
-#include "soc.h"
-#include "common.h"
-
-#define ZOOM_SMSC911X_CS 7
-#define ZOOM_SMSC911X_GPIO 158
-#define ZOOM_QUADUART_CS 3
-#define ZOOM_QUADUART_GPIO 102
-#define ZOOM_QUADUART_RST_GPIO 152
-#define QUART_CLK 1843200
-#define DEBUG_BASE 0x08000000
-#define ZOOM_ETHR_START DEBUG_BASE
-
-static struct omap_smsc911x_platform_data zoom_smsc911x_cfg = {
- .cs = ZOOM_SMSC911X_CS,
- .gpio_irq = ZOOM_SMSC911X_GPIO,
- .gpio_reset = -EINVAL,
- .flags = SMSC911X_USE_32BIT,
-};
-
-static inline void __init zoom_init_smsc911x(void)
-{
- gpmc_smsc911x_init(&zoom_smsc911x_cfg);
-}
-
-static struct plat_serial8250_port serial_platform_data[] = {
- {
- .mapbase = ZOOM_UART_BASE,
- .flags = UPF_BOOT_AUTOCONF|UPF_IOREMAP|UPF_SHARE_IRQ,
- .irqflags = IRQF_SHARED | IRQF_TRIGGER_RISING,
- .iotype = UPIO_MEM,
- .regshift = 1,
- .uartclk = QUART_CLK,
- }, {
- .flags = 0
- }
-};
-
-static struct platform_device zoom_debugboard_serial_device = {
- .name = "serial8250",
- .id = PLAT8250_DEV_PLATFORM,
- .dev = {
- .platform_data = serial_platform_data,
- },
-};
-
-static inline void __init zoom_init_quaduart(void)
-{
- int quart_cs;
- unsigned long cs_mem_base;
- int quart_gpio = 0;
-
- if (gpio_request_one(ZOOM_QUADUART_RST_GPIO,
- GPIOF_OUT_INIT_LOW,
- "TL16CP754C GPIO") < 0) {
- pr_err("Failed to request GPIO%d for TL16CP754C\n",
- ZOOM_QUADUART_RST_GPIO);
- return;
- }
-
- quart_cs = ZOOM_QUADUART_CS;
-
- if (gpmc_cs_request(quart_cs, SZ_1M, &cs_mem_base) < 0) {
- pr_err("Failed to request GPMC mem for Quad UART(TL16CP754C)\n");
- return;
- }
-
- quart_gpio = ZOOM_QUADUART_GPIO;
-
- if (gpio_request_one(quart_gpio, GPIOF_IN, "TL16CP754C GPIO") < 0)
- printk(KERN_ERR "Failed to request GPIO%d for TL16CP754C\n",
- quart_gpio);
-
- serial_platform_data[0].irq = gpio_to_irq(102);
-}
-
-static inline int omap_zoom_debugboard_detect(void)
-{
- int debug_board_detect = 0;
- int ret = 1;
-
- debug_board_detect = ZOOM_SMSC911X_GPIO;
-
- if (gpio_request_one(debug_board_detect, GPIOF_IN,
- "Zoom debug board detect") < 0) {
- pr_err("Failed to request GPIO%d for Zoom debug board detect\n",
- debug_board_detect);
- return 0;
- }
-
- if (!gpio_get_value(debug_board_detect)) {
- ret = 0;
- }
- gpio_free(debug_board_detect);
- return ret;
-}
-
-static struct platform_device *zoom_devices[] __initdata = {
- &zoom_debugboard_serial_device,
-};
-
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
- REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-int __init zoom_debugboard_init(void)
-{
- if (!omap_zoom_debugboard_detect())
- return 0;
-
- regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
- zoom_init_smsc911x();
- zoom_init_quaduart();
- return platform_add_devices(zoom_devices, ARRAY_SIZE(zoom_devices));
-}
diff --git a/arch/arm/mach-omap2/board-zoom-display.c b/arch/arm/mach-omap2/board-zoom-display.c
deleted file mode 100644
index 3d8ecc1e..0000000
--- a/arch/arm/mach-omap2/board-zoom-display.c
+++ /dev/null
@@ -1,71 +0,0 @@
-/*
- * Copyright (C) 2010 Texas Instruments Inc.
- *
- * Modified from mach-omap2/board-zoom-peripherals.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/spi/spi.h>
-#include <linux/platform_data/spi-omap2-mcspi.h>
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include "board-zoom.h"
-#include "soc.h"
-#include "common.h"
-
-#define LCD_PANEL_RESET_GPIO_PROD 96
-#define LCD_PANEL_RESET_GPIO_PILOT 55
-#define LCD_PANEL_QVGA_GPIO 56
-
-static struct panel_nec_nl8048hl11_platform_data zoom_lcd_pdata = {
- .name = "lcd",
- .source = "dpi.0",
-
- .data_lines = 24,
-
- .res_gpio = -1, /* filled in code */
- .qvga_gpio = LCD_PANEL_QVGA_GPIO,
-};
-
-static struct omap_dss_board_info zoom_dss_data = {
- .default_display_name = "lcd",
-};
-
-static void __init zoom_lcd_panel_init(void)
-{
- zoom_lcd_pdata.res_gpio = (omap_rev() > OMAP3430_REV_ES3_0) ?
- LCD_PANEL_RESET_GPIO_PROD :
- LCD_PANEL_RESET_GPIO_PILOT;
-}
-
-static struct omap2_mcspi_device_config dss_lcd_mcspi_config = {
- .turbo_mode = 1,
-};
-
-static struct spi_board_info nec_8048_spi_board_info[] __initdata = {
- [0] = {
- .modalias = "panel-nec-nl8048hl11",
- .bus_num = 1,
- .chip_select = 2,
- .max_speed_hz = 375000,
- .controller_data = &dss_lcd_mcspi_config,
- .platform_data = &zoom_lcd_pdata,
- },
-};
-
-void __init zoom_display_init(void)
-{
- omap_display_init(&zoom_dss_data);
- zoom_lcd_panel_init();
- spi_register_board_info(nec_8048_spi_board_info,
- ARRAY_SIZE(nec_8048_spi_board_info));
-}
-
diff --git a/arch/arm/mach-omap2/board-zoom-peripherals.c b/arch/arm/mach-omap2/board-zoom-peripherals.c
deleted file mode 100644
index a90375d..0000000
--- a/arch/arm/mach-omap2/board-zoom-peripherals.c
+++ /dev/null
@@ -1,360 +0,0 @@
-/*
- * Copyright (C) 2009 Texas Instruments Inc.
- *
- * Modified from mach-omap2/board-zoom2.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/input.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/gpio.h>
-#include <linux/i2c/twl.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-#include <linux/wl12xx.h>
-#include <linux/mmc/host.h>
-#include <linux/platform_data/gpio-omap.h>
-#include <linux/platform_data/omap-twl4030.h>
-#include <linux/usb/phy.h>
-#include <linux/pwm.h>
-#include <linux/leds_pwm.h>
-#include <linux/pwm_backlight.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-
-#include "board-zoom.h"
-
-#include "mux.h"
-#include "hsmmc.h"
-#include "common-board-devices.h"
-
-#define OMAP_ZOOM_WLAN_PMENA_GPIO (101)
-#define OMAP_ZOOM_TSC2004_IRQ_GPIO (153)
-#define OMAP_ZOOM_WLAN_IRQ_GPIO (162)
-
-/* Zoom2 has Qwerty keyboard*/
-static uint32_t board_keymap[] = {
- KEY(0, 0, KEY_E),
- KEY(0, 1, KEY_R),
- KEY(0, 2, KEY_T),
- KEY(0, 3, KEY_HOME),
- KEY(0, 6, KEY_I),
- KEY(0, 7, KEY_LEFTSHIFT),
- KEY(1, 0, KEY_D),
- KEY(1, 1, KEY_F),
- KEY(1, 2, KEY_G),
- KEY(1, 3, KEY_SEND),
- KEY(1, 6, KEY_K),
- KEY(1, 7, KEY_ENTER),
- KEY(2, 0, KEY_X),
- KEY(2, 1, KEY_C),
- KEY(2, 2, KEY_V),
- KEY(2, 3, KEY_END),
- KEY(2, 6, KEY_DOT),
- KEY(2, 7, KEY_CAPSLOCK),
- KEY(3, 0, KEY_Z),
- KEY(3, 1, KEY_KPPLUS),
- KEY(3, 2, KEY_B),
- KEY(3, 3, KEY_F1),
- KEY(3, 6, KEY_O),
- KEY(3, 7, KEY_SPACE),
- KEY(4, 0, KEY_W),
- KEY(4, 1, KEY_Y),
- KEY(4, 2, KEY_U),
- KEY(4, 3, KEY_F2),
- KEY(4, 4, KEY_VOLUMEUP),
- KEY(4, 6, KEY_L),
- KEY(4, 7, KEY_LEFT),
- KEY(5, 0, KEY_S),
- KEY(5, 1, KEY_H),
- KEY(5, 2, KEY_J),
- KEY(5, 3, KEY_F3),
- KEY(5, 4, KEY_UNKNOWN),
- KEY(5, 5, KEY_VOLUMEDOWN),
- KEY(5, 6, KEY_M),
- KEY(5, 7, KEY_RIGHT),
- KEY(6, 0, KEY_Q),
- KEY(6, 1, KEY_A),
- KEY(6, 2, KEY_N),
- KEY(6, 3, KEY_BACKSPACE),
- KEY(6, 6, KEY_P),
- KEY(6, 7, KEY_UP),
- KEY(7, 0, KEY_PROG1), /*MACRO 1 <User defined> */
- KEY(7, 1, KEY_PROG2), /*MACRO 2 <User defined> */
- KEY(7, 2, KEY_PROG3), /*MACRO 3 <User defined> */
- KEY(7, 3, KEY_PROG4), /*MACRO 4 <User defined> */
- KEY(7, 6, KEY_SELECT),
- KEY(7, 7, KEY_DOWN)
-};
-
-static struct matrix_keymap_data board_map_data = {
- .keymap = board_keymap,
- .keymap_size = ARRAY_SIZE(board_keymap),
-};
-
-static struct twl4030_keypad_data zoom_kp_twl4030_data = {
- .keymap_data = &board_map_data,
- .rows = 8,
- .cols = 8,
- .rep = 1,
-};
-
-static struct regulator_consumer_supply zoom_vmmc1_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply zoom_vsim_supply[] = {
- REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply zoom_vmmc2_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
-};
-
-static struct regulator_consumer_supply zoom_vmmc3_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.2"),
-};
-
-/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
-static struct regulator_init_data zoom_vmmc1 = {
- .constraints = {
- .min_uV = 1850000,
- .max_uV = 3150000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(zoom_vmmc1_supply),
- .consumer_supplies = zoom_vmmc1_supply,
-};
-
-/* VMMC2 for MMC2 card */
-static struct regulator_init_data zoom_vmmc2 = {
- .constraints = {
- .min_uV = 1850000,
- .max_uV = 1850000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(zoom_vmmc2_supply),
- .consumer_supplies = zoom_vmmc2_supply,
-};
-
-/* VSIM for OMAP VDD_MMC1A (i/o for DAT4..DAT7) */
-static struct regulator_init_data zoom_vsim = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 3000000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(zoom_vsim_supply),
- .consumer_supplies = zoom_vsim_supply,
-};
-
-static struct regulator_init_data zoom_vmmc3 = {
- .constraints = {
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(zoom_vmmc3_supply),
- .consumer_supplies = zoom_vmmc3_supply,
-};
-
-static struct fixed_voltage_config zoom_vwlan = {
- .supply_name = "vwl1271",
- .microvolts = 1800000, /* 1.8V */
- .gpio = OMAP_ZOOM_WLAN_PMENA_GPIO,
- .startup_delay = 70000, /* 70msec */
- .enable_high = 1,
- .enabled_at_boot = 0,
- .init_data = &zoom_vmmc3,
-};
-
-static struct platform_device omap_vwlan_device = {
- .name = "reg-fixed-voltage",
- .id = 1,
- .dev = {
- .platform_data = &zoom_vwlan,
- },
-};
-
-static struct pwm_lookup zoom_pwm_lookup[] = {
- PWM_LOOKUP("twl-pwm", 0, "leds_pwm", "zoom::keypad"),
- PWM_LOOKUP("twl-pwm", 1, "pwm-backlight", "backlight"),
-};
-
-static struct led_pwm zoom_pwm_leds[] = {
- {
- .name = "zoom::keypad",
- .max_brightness = 127,
- .pwm_period_ns = 7812500,
- },
-};
-
-static struct led_pwm_platform_data zoom_pwm_data = {
- .num_leds = ARRAY_SIZE(zoom_pwm_leds),
- .leds = zoom_pwm_leds,
-};
-
-static struct platform_device zoom_leds_pwm = {
- .name = "leds_pwm",
- .id = -1,
- .dev = {
- .platform_data = &zoom_pwm_data,
- },
-};
-
-static struct platform_pwm_backlight_data zoom_backlight_data = {
- .pwm_id = 1,
- .max_brightness = 127,
- .dft_brightness = 127,
- .pwm_period_ns = 7812500,
-};
-
-static struct platform_device zoom_backlight_pwm = {
- .name = "pwm-backlight",
- .id = -1,
- .dev = {
- .platform_data = &zoom_backlight_data,
- },
-};
-
-static struct platform_device *zoom_devices[] __initdata = {
- &omap_vwlan_device,
- &zoom_leds_pwm,
- &zoom_backlight_pwm,
-};
-
-static struct wl12xx_platform_data omap_zoom_wlan_data __initdata = {
- .board_ref_clock = WL12XX_REFCLOCK_26, /* 26 MHz */
-};
-
-static struct omap2_hsmmc_info mmc[] = {
- {
- .name = "external",
- .mmc = 1,
- .caps = MMC_CAP_4_BIT_DATA,
- .gpio_wp = -EINVAL,
- .power_saving = true,
- .deferred = true,
- },
- {
- .name = "internal",
- .mmc = 2,
- .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
- .gpio_cd = -EINVAL,
- .gpio_wp = -EINVAL,
- .nonremovable = true,
- .power_saving = true,
- },
- {
- .name = "wl1271",
- .mmc = 3,
- .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_POWER_OFF_CARD,
- .gpio_wp = -EINVAL,
- .gpio_cd = -EINVAL,
- .nonremovable = true,
- },
- {} /* Terminator */
-};
-
-static struct omap_tw4030_pdata omap_twl4030_audio_data = {
- .voice_connected = true,
- .custom_routing = true,
-
- .has_hs = OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT,
- .has_hf = OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT,
-
- .has_mainmic = true,
- .has_submic = true,
- .has_hsmic = true,
- .has_linein = OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT,
-};
-
-static int zoom_twl_gpio_setup(struct device *dev,
- unsigned gpio, unsigned ngpio)
-{
- /* gpio + 0 is "mmc0_cd" (input/IRQ) */
- mmc[0].gpio_cd = gpio + 0;
- omap_hsmmc_late_init(mmc);
-
- /* Audio setup */
- omap_twl4030_audio_data.jack_detect = gpio + 2;
- omap_twl4030_audio_init("Zoom2", &omap_twl4030_audio_data);
-
- return 0;
-}
-
-static struct twl4030_gpio_platform_data zoom_gpio_data = {
- .setup = zoom_twl_gpio_setup,
-};
-
-static struct twl4030_platform_data zoom_twldata = {
- /* platform_data for children goes here */
- .gpio = &zoom_gpio_data,
- .keypad = &zoom_kp_twl4030_data,
- .vmmc1 = &zoom_vmmc1,
- .vmmc2 = &zoom_vmmc2,
- .vsim = &zoom_vsim,
-};
-
-static int __init omap_i2c_init(void)
-{
- omap3_pmic_get_config(&zoom_twldata,
- TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_BCI |
- TWL_COMMON_PDATA_MADC | TWL_COMMON_PDATA_AUDIO,
- TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
-
- if (machine_is_omap_zoom2())
- zoom_twldata.audio->codec->ramp_delay_value = 3; /* 161 ms */
-
- omap_pmic_init(1, 2400, "twl5030", 7 + OMAP_INTC_START, &zoom_twldata);
- omap_register_i2c_bus(2, 400, NULL, 0);
- omap_register_i2c_bus(3, 400, NULL, 0);
- return 0;
-}
-
-static void enable_board_wakeup_source(void)
-{
- /* T2 interrupt line (keypad) */
- omap_mux_init_signal("sys_nirq",
- OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
-}
-
-void __init zoom_peripherals_init(void)
-{
- int ret;
-
- omap_zoom_wlan_data.irq = gpio_to_irq(OMAP_ZOOM_WLAN_IRQ_GPIO);
- ret = wl12xx_set_platform_data(&omap_zoom_wlan_data);
-
- if (ret)
- pr_err("error setting wl12xx data: %d\n", ret);
-
- omap_hsmmc_init(mmc);
- omap_i2c_init();
- pwm_add_table(zoom_pwm_lookup, ARRAY_SIZE(zoom_pwm_lookup));
- platform_add_devices(zoom_devices, ARRAY_SIZE(zoom_devices));
- usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
- usb_musb_init(NULL);
- enable_board_wakeup_source();
- omap_serial_init();
-}
diff --git a/arch/arm/mach-omap2/board-zoom.c b/arch/arm/mach-omap2/board-zoom.c
deleted file mode 100644
index 1a3dd86..0000000
--- a/arch/arm/mach-omap2/board-zoom.c
+++ /dev/null
@@ -1,159 +0,0 @@
-/*
- * Copyright (C) 2009-2010 Texas Instruments Inc.
- * Mikkel Christensen <mlc@ti.com>
- * Felipe Balbi <balbi@ti.com>
- *
- * Modified from mach-omap2/board-ldp.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/input.h>
-#include <linux/gpio.h>
-#include <linux/i2c/twl.h>
-#include <linux/mtd/nand.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include "common.h"
-
-#include "board-zoom.h"
-
-#include "board-flash.h"
-#include "mux.h"
-#include "sdram-micron-mt46h32m32lf-6.h"
-#include "sdram-hynix-h8mbx00u0mer-0em.h"
-
-#define ZOOM3_EHCI_RESET_GPIO 64
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
- /* WLAN IRQ - GPIO 162 */
- OMAP3_MUX(MCBSP1_CLKX, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
- /* WLAN POWER ENABLE - GPIO 101 */
- OMAP3_MUX(CAM_D2, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
- /* WLAN SDIO: MMC3 CMD */
- OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE3 | OMAP_PIN_INPUT_PULLUP),
- /* WLAN SDIO: MMC3 CLK */
- OMAP3_MUX(ETK_CLK, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP),
- /* WLAN SDIO: MMC3 DAT[0-3] */
- OMAP3_MUX(ETK_D3, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP),
- OMAP3_MUX(ETK_D4, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP),
- OMAP3_MUX(ETK_D5, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP),
- OMAP3_MUX(ETK_D6, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP),
- { .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static struct mtd_partition zoom_nand_partitions[] = {
- /* All the partition sizes are listed in terms of NAND block size */
- {
- .name = "X-Loader-NAND",
- .offset = 0,
- .size = 4 * (64 * 2048), /* 512KB, 0x80000 */
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "U-Boot-NAND",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
- .size = 10 * (64 * 2048), /* 1.25MB, 0x140000 */
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "Boot Env-NAND",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x1c0000 */
- .size = 2 * (64 * 2048), /* 256KB, 0x40000 */
- },
- {
- .name = "Kernel-NAND",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x0200000*/
- .size = 240 * (64 * 2048), /* 30M, 0x1E00000 */
- },
- {
- .name = "system",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x2000000 */
- .size = 3328 * (64 * 2048), /* 416M, 0x1A000000 */
- },
- {
- .name = "userdata",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x1C000000*/
- .size = 256 * (64 * 2048), /* 32M, 0x2000000 */
- },
- {
- .name = "cache",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x1E000000*/
- .size = 256 * (64 * 2048), /* 32M, 0x2000000 */
- },
-};
-
-static struct usbhs_phy_data phy_data[] __initdata = {
- {
- .port = 2,
- .reset_gpio = ZOOM3_EHCI_RESET_GPIO,
- .vcc_gpio = -EINVAL,
- },
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
- .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-static void __init omap_zoom_init(void)
-{
- if (machine_is_omap_zoom2()) {
- omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
- } else if (machine_is_omap_zoom3()) {
- omap3_mux_init(board_mux, OMAP_PACKAGE_CBP);
- omap_mux_init_gpio(ZOOM3_EHCI_RESET_GPIO, OMAP_PIN_OUTPUT);
-
- usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
- usbhs_init(&usbhs_bdata);
- }
-
- board_nand_init(zoom_nand_partitions,
- ARRAY_SIZE(zoom_nand_partitions), ZOOM_NAND_CS,
- NAND_BUSWIDTH_16, nand_default_timings);
- zoom_debugboard_init();
- zoom_peripherals_init();
-
- if (machine_is_omap_zoom2())
- omap_sdrc_init(mt46h32m32lf6_sdrc_params,
- mt46h32m32lf6_sdrc_params);
- else if (machine_is_omap_zoom3())
- omap_sdrc_init(h8mbx00u0mer0em_sdrc_params,
- h8mbx00u0mer0em_sdrc_params);
-
- zoom_display_init();
-}
-
-MACHINE_START(OMAP_ZOOM2, "OMAP Zoom2 board")
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap3430_init_early,
- .init_irq = omap3_init_irq,
- .handle_irq = omap3_intc_handle_irq,
- .init_machine = omap_zoom_init,
- .init_late = omap3430_init_late,
- .init_time = omap3_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
-
-MACHINE_START(OMAP_ZOOM3, "OMAP Zoom3 board")
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap3630_init_early,
- .init_irq = omap3_init_irq,
- .handle_irq = omap3_intc_handle_irq,
- .init_machine = omap_zoom_init,
- .init_late = omap3630_init_late,
- .init_time = omap3_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-zoom.h b/arch/arm/mach-omap2/board-zoom.h
deleted file mode 100644
index 2e94869..0000000
--- a/arch/arm/mach-omap2/board-zoom.h
+++ /dev/null
@@ -1,10 +0,0 @@
-/*
- * Defines for zoom boards
- */
-#include <video/omapdss.h>
-
-#define ZOOM_NAND_CS 0
-
-extern int __init zoom_debugboard_init(void);
-extern void __init zoom_peripherals_init(void);
-extern void __init zoom_display_init(void);
diff --git a/arch/arm/mach-omap2/common.h b/arch/arm/mach-omap2/common.h
index 4a5684b..f7644fe 100644
--- a/arch/arm/mach-omap2/common.h
+++ b/arch/arm/mach-omap2/common.h
@@ -98,6 +98,7 @@
void ti81xx_init_early(void);
void am33xx_init_early(void);
void am43xx_init_early(void);
+void am43xx_init_late(void);
void omap4430_init_early(void);
void omap5_init_early(void);
void omap3_init_late(void); /* Do not use this one */
@@ -109,8 +110,11 @@
void omap3630_init_late(void);
void am35xx_init_late(void);
void ti81xx_init_late(void);
+void am33xx_init_late(void);
+void omap5_init_late(void);
int omap2_common_pm_late_init(void);
void dra7xx_init_early(void);
+void dra7xx_init_late(void);
#ifdef CONFIG_SOC_BUS
void omap_soc_device_init(void);
@@ -288,6 +292,9 @@
#endif
+void pdata_quirks_init(struct of_device_id *);
+void omap_pcs_legacy_init(int irq, void (*rearm)(void));
+
struct omap_sdrc_params;
extern void omap_sdrc_init(struct omap_sdrc_params *sdrc_cs0,
struct omap_sdrc_params *sdrc_cs1);
diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index 5c5315b..5336c75 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -19,7 +19,6 @@
#include <linux/of.h>
#include <linux/pinctrl/machine.h>
#include <linux/platform_data/omap4-keypad.h>
-#include <linux/wl12xx.h>
#include <linux/platform_data/mailbox-omap.h>
#include <asm/mach-types.h>
@@ -475,40 +474,6 @@
static inline void omap_init_vout(void) {}
#endif
-#if IS_ENABLED(CONFIG_WL12XX)
-
-static struct wl12xx_platform_data wl12xx __initdata;
-
-void __init omap_init_wl12xx_of(void)
-{
- int ret;
-
- if (!of_have_populated_dt())
- return;
-
- if (of_machine_is_compatible("ti,omap4-sdp")) {
- wl12xx.board_ref_clock = WL12XX_REFCLOCK_26;
- wl12xx.board_tcxo_clock = WL12XX_TCXOCLOCK_26;
- wl12xx.irq = gpio_to_irq(53);
- } else if (of_machine_is_compatible("ti,omap4-panda")) {
- wl12xx.board_ref_clock = WL12XX_REFCLOCK_38;
- wl12xx.irq = gpio_to_irq(53);
- } else {
- return;
- }
-
- ret = wl12xx_set_platform_data(&wl12xx);
- if (ret) {
- pr_err("error setting wl12xx data: %d\n", ret);
- return;
- }
-}
-#else
-static inline void omap_init_wl12xx_of(void)
-{
-}
-#endif
-
/*-------------------------------------------------------------------------*/
static int __init omap2_init_devices(void)
@@ -531,9 +496,6 @@
omap_init_sham();
omap_init_aes();
omap_init_rng();
- } else {
- /* These can be removed when bindings are done */
- omap_init_wl12xx_of();
}
omap_init_sti();
omap_init_vout();
diff --git a/arch/arm/mach-omap2/dss-common.c b/arch/arm/mach-omap2/dss-common.c
index bf89eff..365bfd3 100644
--- a/arch/arm/mach-omap2/dss-common.c
+++ b/arch/arm/mach-omap2/dss-common.c
@@ -213,3 +213,47 @@
platform_device_register(&sdp4430_tpd_device);
platform_device_register(&sdp4430_hdmi_connector_device);
}
+
+
+/* OMAP3 IGEPv2 data */
+
+#define IGEP2_DVI_TFP410_POWER_DOWN_GPIO 170
+
+/* DVI Connector */
+static struct connector_dvi_platform_data omap3_igep2_dvi_connector_pdata = {
+ .name = "dvi",
+ .source = "tfp410.0",
+ .i2c_bus_num = 3,
+};
+
+static struct platform_device omap3_igep2_dvi_connector_device = {
+ .name = "connector-dvi",
+ .id = 0,
+ .dev.platform_data = &omap3_igep2_dvi_connector_pdata,
+};
+
+/* TFP410 DPI-to-DVI chip */
+static struct encoder_tfp410_platform_data omap3_igep2_tfp410_pdata = {
+ .name = "tfp410.0",
+ .source = "dpi.0",
+ .data_lines = 24,
+ .power_down_gpio = IGEP2_DVI_TFP410_POWER_DOWN_GPIO,
+};
+
+static struct platform_device omap3_igep2_tfp410_device = {
+ .name = "tfp410",
+ .id = 0,
+ .dev.platform_data = &omap3_igep2_tfp410_pdata,
+};
+
+static struct omap_dss_board_info igep2_dss_data = {
+ .default_display_name = "dvi",
+};
+
+void __init omap3_igep2_display_init_of(void)
+{
+ omap_display_init(&igep2_dss_data);
+
+ platform_device_register(&omap3_igep2_tfp410_device);
+ platform_device_register(&omap3_igep2_dvi_connector_device);
+}
diff --git a/arch/arm/mach-omap2/dss-common.h b/arch/arm/mach-omap2/dss-common.h
index c28fe3c..a9becf0 100644
--- a/arch/arm/mach-omap2/dss-common.h
+++ b/arch/arm/mach-omap2/dss-common.h
@@ -8,5 +8,6 @@
void __init omap4_panda_display_init_of(void);
void __init omap_4430sdp_display_init_of(void);
+void __init omap3_igep2_display_init_of(void);
#endif
diff --git a/arch/arm/mach-omap2/gpmc-onenand.c b/arch/arm/mach-omap2/gpmc-onenand.c
index 64b5a83..8b6876c 100644
--- a/arch/arm/mach-omap2/gpmc-onenand.c
+++ b/arch/arm/mach-omap2/gpmc-onenand.c
@@ -272,9 +272,19 @@
struct gpmc_timings t;
int ret;
- if (gpmc_onenand_data->of_node)
+ if (gpmc_onenand_data->of_node) {
gpmc_read_settings_dt(gpmc_onenand_data->of_node,
&onenand_async);
+ if (onenand_async.sync_read || onenand_async.sync_write) {
+ if (onenand_async.sync_write)
+ gpmc_onenand_data->flags |=
+ ONENAND_SYNC_READWRITE;
+ else
+ gpmc_onenand_data->flags |= ONENAND_SYNC_READ;
+ onenand_async.sync_read = false;
+ onenand_async.sync_write = false;
+ }
+ }
omap2_onenand_set_async_mode(onenand_base);
diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c
index 579697a..51525fa 100644
--- a/arch/arm/mach-omap2/gpmc.c
+++ b/arch/arm/mach-omap2/gpmc.c
@@ -1521,6 +1521,42 @@
return ret;
}
+/*
+ * REVISIT: Add timing support from slls644g.pdf
+ */
+static int gpmc_probe_8250(struct platform_device *pdev,
+ struct device_node *child)
+{
+ struct resource res;
+ unsigned long base;
+ int ret, cs;
+
+ if (of_property_read_u32(child, "reg", &cs) < 0) {
+ dev_err(&pdev->dev, "%s has no 'reg' property\n",
+ child->full_name);
+ return -ENODEV;
+ }
+
+ if (of_address_to_resource(child, 0, &res) < 0) {
+ dev_err(&pdev->dev, "%s has malformed 'reg' property\n",
+ child->full_name);
+ return -ENODEV;
+ }
+
+ ret = gpmc_cs_request(cs, resource_size(&res), &base);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "cannot request GPMC CS %d\n", cs);
+ return ret;
+ }
+
+ if (of_platform_device_create(child, NULL, &pdev->dev))
+ return 0;
+
+ dev_err(&pdev->dev, "failed to create gpmc child %s\n", child->name);
+
+ return -ENODEV;
+}
+
static int gpmc_probe_dt(struct platform_device *pdev)
{
int ret;
@@ -1564,6 +1600,8 @@
else if (of_node_cmp(child->name, "ethernet") == 0 ||
of_node_cmp(child->name, "nor") == 0)
ret = gpmc_probe_generic_child(pdev, child);
+ else if (of_node_cmp(child->name, "8250") == 0)
+ ret = gpmc_probe_8250(pdev, child);
if (WARN(ret < 0, "%s: probing gpmc child %s failed\n",
__func__, child->full_name))
diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c
index ff2113c..a2cbb44 100644
--- a/arch/arm/mach-omap2/io.c
+++ b/arch/arm/mach-omap2/io.c
@@ -583,6 +583,11 @@
omap_hwmod_init_postsetup();
omap_clk_init = am33xx_clk_init;
}
+
+void __init am33xx_init_late(void)
+{
+ omap_common_late_init();
+}
#endif
#ifdef CONFIG_SOC_AM43XX
@@ -596,6 +601,11 @@
omap2_set_globals_cm(AM33XX_L4_WK_IO_ADDRESS(AM43XX_PRCM_BASE), NULL);
omap3xxx_check_revision();
}
+
+void __init am43xx_init_late(void)
+{
+ omap_common_late_init();
+}
#endif
#ifdef CONFIG_ARCH_OMAP4
@@ -651,6 +661,11 @@
omap54xx_hwmod_init();
omap_hwmod_init_postsetup();
}
+
+void __init omap5_init_late(void)
+{
+ omap_common_late_init();
+}
#endif
#ifdef CONFIG_SOC_DRA7XX
@@ -671,6 +686,11 @@
dra7xx_hwmod_init();
omap_hwmod_init_postsetup();
}
+
+void __init dra7xx_init_late(void)
+{
+ omap_common_late_init();
+}
#endif
diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c
index f82cf87..48094b5 100644
--- a/arch/arm/mach-omap2/mux.c
+++ b/arch/arm/mach-omap2/mux.c
@@ -811,6 +811,12 @@
}
}
+ omap_mux_dbg_init();
+
+ /* see pinctrl-single-omap for the wake-up interrupt handling */
+ if (of_have_populated_dt())
+ return 0;
+
ret = request_irq(omap_prcm_event_to_irq("io"),
omap_hwmod_mux_handle_irq, IRQF_SHARED | IRQF_NO_SUSPEND,
"hwmod_io", omap_mux_late_init);
@@ -818,8 +824,6 @@
if (ret)
pr_warning("mux: Failed to setup hwmod io irq %d\n", ret);
- omap_mux_dbg_init();
-
return 0;
}
diff --git a/arch/arm/mach-omap2/mux.h b/arch/arm/mach-omap2/mux.h
index 5d2080e..16f78a9 100644
--- a/arch/arm/mach-omap2/mux.h
+++ b/arch/arm/mach-omap2/mux.h
@@ -28,7 +28,7 @@
#define OMAP_PULL_UP (1 << 4)
#define OMAP_ALTELECTRICALSEL (1 << 5)
-/* 34xx specific mux bit defines */
+/* omap3/4/5 specific mux bit defines */
#define OMAP_INPUT_EN (1 << 8)
#define OMAP_OFF_EN (1 << 9)
#define OMAP_OFFOUT_EN (1 << 10)
@@ -36,8 +36,6 @@
#define OMAP_OFF_PULL_EN (1 << 12)
#define OMAP_OFF_PULL_UP (1 << 13)
#define OMAP_WAKEUP_EN (1 << 14)
-
-/* 44xx specific mux bit defines */
#define OMAP_WAKEUP_EVENT (1 << 15)
/* Active pin states */
diff --git a/arch/arm/mach-omap2/opp.c b/arch/arm/mach-omap2/opp.c
index bd41d59..82fd8c7 100644
--- a/arch/arm/mach-omap2/opp.c
+++ b/arch/arm/mach-omap2/opp.c
@@ -17,6 +17,7 @@
* GNU General Public License for more details.
*/
#include <linux/module.h>
+#include <linux/of.h>
#include <linux/opp.h>
#include <linux/cpu.h>
@@ -40,6 +41,9 @@
{
int i, r;
+ if (of_have_populated_dt())
+ return -EINVAL;
+
if (!opp_def || !opp_def_size) {
pr_err("%s: invalid params!\n", __func__);
return -EINVAL;
diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c
new file mode 100644
index 0000000..10c7145
--- /dev/null
+++ b/arch/arm/mach-omap2/pdata-quirks.c
@@ -0,0 +1,174 @@
+/*
+ * Legacy platform_data quirks
+ *
+ * Copyright (C) 2013 Texas Instruments
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/clk.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/of_platform.h>
+#include <linux/wl12xx.h>
+
+#include <linux/platform_data/pinctrl-single.h>
+
+#include "common.h"
+#include "common-board-devices.h"
+#include "dss-common.h"
+#include "control.h"
+
+struct pdata_init {
+ const char *compatible;
+ void (*fn)(void);
+};
+
+/*
+ * Create alias for USB host PHY clock.
+ * Remove this when clock phandle can be provided via DT
+ */
+static void __init __used legacy_init_ehci_clk(char *clkname)
+{
+ int ret;
+
+ ret = clk_add_alias("main_clk", NULL, clkname, NULL);
+ if (ret)
+ pr_err("%s:Failed to add main_clk alias to %s :%d\n",
+ __func__, clkname, ret);
+}
+
+#if IS_ENABLED(CONFIG_WL12XX)
+
+static struct wl12xx_platform_data wl12xx __initdata;
+
+static void __init __used legacy_init_wl12xx(unsigned ref_clock,
+ unsigned tcxo_clock,
+ int gpio)
+{
+ int res;
+
+ wl12xx.board_ref_clock = ref_clock;
+ wl12xx.board_tcxo_clock = tcxo_clock;
+ wl12xx.irq = gpio_to_irq(gpio);
+
+ res = wl12xx_set_platform_data(&wl12xx);
+ if (res) {
+ pr_err("error setting wl12xx data: %d\n", res);
+ return;
+ }
+}
+#else
+static inline void legacy_init_wl12xx(unsigned ref_clock,
+ unsigned tcxo_clock,
+ int gpio)
+{
+}
+#endif
+
+#ifdef CONFIG_ARCH_OMAP3
+static void __init hsmmc2_internal_input_clk(void)
+{
+ u32 reg;
+
+ reg = omap_ctrl_readl(OMAP343X_CONTROL_DEVCONF1);
+ reg |= OMAP2_MMCSDIO2ADPCLKISEL;
+ omap_ctrl_writel(reg, OMAP343X_CONTROL_DEVCONF1);
+}
+
+static void __init omap3_igep0020_legacy_init(void)
+{
+ omap3_igep2_display_init_of();
+}
+
+static void __init omap3_evm_legacy_init(void)
+{
+ legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 149);
+}
+
+static void __init omap3_zoom_legacy_init(void)
+{
+ legacy_init_wl12xx(WL12XX_REFCLOCK_26, 0, 162);
+}
+#endif /* CONFIG_ARCH_OMAP3 */
+
+#ifdef CONFIG_ARCH_OMAP4
+static void __init omap4_sdp_legacy_init(void)
+{
+ omap_4430sdp_display_init_of();
+ legacy_init_wl12xx(WL12XX_REFCLOCK_26,
+ WL12XX_TCXOCLOCK_26, 53);
+}
+
+static void __init omap4_panda_legacy_init(void)
+{
+ omap4_panda_display_init_of();
+ legacy_init_ehci_clk("auxclk3_ck");
+ legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 53);
+}
+#endif
+
+#ifdef CONFIG_SOC_OMAP5
+static void __init omap5_uevm_legacy_init(void)
+{
+ legacy_init_ehci_clk("auxclk1_ck");
+}
+#endif
+
+static struct pcs_pdata pcs_pdata;
+
+void omap_pcs_legacy_init(int irq, void (*rearm)(void))
+{
+ pcs_pdata.irq = irq;
+ pcs_pdata.rearm = rearm;
+}
+
+struct of_dev_auxdata omap_auxdata_lookup[] __initdata = {
+#ifdef CONFIG_ARCH_OMAP3
+ OF_DEV_AUXDATA("ti,omap3-padconf", 0x48002030, "48002030.pinmux", &pcs_pdata),
+ OF_DEV_AUXDATA("ti,omap3-padconf", 0x48002a00, "48002a00.pinmux", &pcs_pdata),
+#endif
+#ifdef CONFIG_ARCH_OMAP4
+ OF_DEV_AUXDATA("ti,omap4-padconf", 0x4a100040, "4a100040.pinmux", &pcs_pdata),
+ OF_DEV_AUXDATA("ti,omap4-padconf", 0x4a31e040, "4a31e040.pinmux", &pcs_pdata),
+#endif
+ { /* sentinel */ },
+};
+
+static struct pdata_init pdata_quirks[] __initdata = {
+#ifdef CONFIG_ARCH_OMAP3
+ { "nokia,omap3-n9", hsmmc2_internal_input_clk, },
+ { "nokia,omap3-n950", hsmmc2_internal_input_clk, },
+ { "isee,omap3-igep0020", omap3_igep0020_legacy_init, },
+ { "ti,omap3-evm-37xx", omap3_evm_legacy_init, },
+ { "ti,omap3-zoom3", omap3_zoom_legacy_init, },
+#endif
+#ifdef CONFIG_ARCH_OMAP4
+ { "ti,omap4-sdp", omap4_sdp_legacy_init, },
+ { "ti,omap4-panda", omap4_panda_legacy_init, },
+#endif
+#ifdef CONFIG_SOC_OMAP5
+ { "ti,omap5-uevm", omap5_uevm_legacy_init, },
+#endif
+ { /* sentinel */ },
+};
+
+void __init pdata_quirks_init(struct of_device_id *omap_dt_match_table)
+{
+ struct pdata_init *quirks = pdata_quirks;
+
+ omap_sdrc_init(NULL, NULL);
+ of_platform_populate(NULL, omap_dt_match_table,
+ omap_auxdata_lookup, NULL);
+
+ while (quirks->compatible) {
+ if (of_machine_is_compatible(quirks->compatible)) {
+ if (quirks->fn)
+ quirks->fn();
+ break;
+ }
+ quirks++;
+ }
+}
diff --git a/arch/arm/mach-omap2/pm.c b/arch/arm/mach-omap2/pm.c
index e742118..360b2da 100644
--- a/arch/arm/mach-omap2/pm.c
+++ b/arch/arm/mach-omap2/pm.c
@@ -266,7 +266,12 @@
static inline void omap_init_cpufreq(void)
{
- struct platform_device_info devinfo = { .name = "omap-cpufreq", };
+ struct platform_device_info devinfo = { };
+
+ if (!of_have_populated_dt())
+ devinfo.name = "omap-cpufreq";
+ else
+ devinfo.name = "cpufreq-cpu0";
platform_device_register_full(&devinfo);
}
@@ -300,10 +305,11 @@
/* Smartreflex device init */
omap_devinit_smartreflex();
- /* cpufreq dummy device instantiation */
- omap_init_cpufreq();
}
+ /* cpufreq dummy device instantiation */
+ omap_init_cpufreq();
+
#ifdef CONFIG_SUSPEND
suspend_set_ops(&omap_pm_ops);
#endif
diff --git a/arch/arm/mach-omap2/prm3xxx.h b/arch/arm/mach-omap2/prm3xxx.h
index 277f717..f8eb833 100644
--- a/arch/arm/mach-omap2/prm3xxx.h
+++ b/arch/arm/mach-omap2/prm3xxx.h
@@ -144,7 +144,13 @@
extern void omap3_prm_vcvp_write(u32 val, u8 offset);
extern u32 omap3_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset);
-extern void omap3xxx_prm_reconfigure_io_chain(void);
+#ifdef CONFIG_ARCH_OMAP3
+void omap3xxx_prm_reconfigure_io_chain(void);
+#else
+static inline void omap3xxx_prm_reconfigure_io_chain(void)
+{
+}
+#endif
/* PRM interrupt-related functions */
extern void omap3xxx_prm_read_pending_irqs(unsigned long *events);
diff --git a/arch/arm/mach-omap2/prm44xx_54xx.h b/arch/arm/mach-omap2/prm44xx_54xx.h
index 7cd22ab..a085d9c 100644
--- a/arch/arm/mach-omap2/prm44xx_54xx.h
+++ b/arch/arm/mach-omap2/prm44xx_54xx.h
@@ -42,7 +42,13 @@
extern void omap4_prm_vcvp_write(u32 val, u8 offset);
extern u32 omap4_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset);
-extern void omap44xx_prm_reconfigure_io_chain(void);
+#if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5)
+void omap44xx_prm_reconfigure_io_chain(void);
+#else
+static inline void omap44xx_prm_reconfigure_io_chain(void)
+{
+}
+#endif
/* PRM interrupt-related functions */
extern void omap44xx_prm_read_pending_irqs(unsigned long *events);
diff --git a/arch/arm/mach-omap2/prm_common.c b/arch/arm/mach-omap2/prm_common.c
index 228b850..a2e1174 100644
--- a/arch/arm/mach-omap2/prm_common.c
+++ b/arch/arm/mach-omap2/prm_common.c
@@ -24,6 +24,7 @@
#include <linux/interrupt.h>
#include <linux/slab.h>
+#include "soc.h"
#include "prm2xxx_3xxx.h"
#include "prm2xxx.h"
#include "prm3xxx.h"
@@ -322,6 +323,16 @@
prcm_irq_chips[i] = gc;
}
+ if (of_have_populated_dt()) {
+ int irq = omap_prcm_event_to_irq("io");
+ if (cpu_is_omap34xx())
+ omap_pcs_legacy_init(irq,
+ omap3xxx_prm_reconfigure_io_chain);
+ else
+ omap_pcs_legacy_init(irq,
+ omap44xx_prm_reconfigure_io_chain);
+ }
+
return 0;
err:
diff --git a/arch/arm/mach-omap2/timer.c b/arch/arm/mach-omap2/timer.c
index fa74a06..ead48fa 100644
--- a/arch/arm/mach-omap2/timer.c
+++ b/arch/arm/mach-omap2/timer.c
@@ -628,7 +628,7 @@
#endif /* CONFIG_HAVE_ARM_TWD */
#endif /* CONFIG_ARCH_OMAP4 */
-#ifdef CONFIG_SOC_OMAP5
+#if defined(CONFIG_SOC_OMAP5) || defined(CONFIG_SOC_DRA7XX)
void __init omap5_realtime_timer_init(void)
{
omap4_sync32k_timer_init();
@@ -636,7 +636,7 @@
clocksource_of_init();
}
-#endif /* CONFIG_SOC_OMAP5 */
+#endif /* CONFIG_SOC_OMAP5 || CONFIG_SOC_DRA7XX */
/**
* omap_timer_init - build and register timer device with an
diff --git a/arch/arm/mach-s3c64xx/Kconfig b/arch/arm/mach-s3c64xx/Kconfig
index 041da51..bd14e3a 100644
--- a/arch/arm/mach-s3c64xx/Kconfig
+++ b/arch/arm/mach-s3c64xx/Kconfig
@@ -306,3 +306,19 @@
select SAMSUNG_GPIO_EXTRA128
help
Machine support for the Wolfson Cragganmore S3C6410 variant.
+
+config MACH_S3C64XX_DT
+ bool "Samsung S3C6400/S3C6410 machine using Device Tree"
+ select CLKSRC_OF
+ select CPU_S3C6400
+ select CPU_S3C6410
+ select PINCTRL
+ select PINCTRL_S3C64XX
+ select USE_OF
+ help
+ Machine support for Samsung S3C6400/S3C6410 machines with Device Tree
+ enabled.
+ Select this if a fdt blob is available for your S3C64XX SoC based
+ board.
+ Note: This is under development and not all peripherals can be
+ supported with this machine file.
diff --git a/arch/arm/mach-s3c64xx/Makefile b/arch/arm/mach-s3c64xx/Makefile
index 31d0c91..6faedcf 100644
--- a/arch/arm/mach-s3c64xx/Makefile
+++ b/arch/arm/mach-s3c64xx/Makefile
@@ -12,7 +12,7 @@
# Core
-obj-y += common.o clock.o
+obj-y += common.o
# Core support
@@ -57,3 +57,4 @@
obj-$(CONFIG_MACH_SMDK6400) += mach-smdk6400.o
obj-$(CONFIG_MACH_SMDK6410) += mach-smdk6410.o
obj-$(CONFIG_MACH_WLF_CRAGG_6410) += mach-crag6410.o mach-crag6410-module.o
+obj-$(CONFIG_MACH_S3C64XX_DT) += mach-s3c64xx-dt.o
diff --git a/arch/arm/mach-s3c64xx/clock.c b/arch/arm/mach-s3c64xx/clock.c
deleted file mode 100644
index c1bcc4a6..0000000
--- a/arch/arm/mach-s3c64xx/clock.c
+++ /dev/null
@@ -1,1007 +0,0 @@
-/* linux/arch/arm/plat-s3c64xx/clock.c
- *
- * Copyright 2008 Openmoko, Inc.
- * Copyright 2008 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- * http://armlinux.simtec.co.uk/
- *
- * S3C64XX Base clock support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/io.h>
-
-#include <mach/hardware.h>
-#include <mach/map.h>
-
-#include <mach/regs-clock.h>
-
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/cpu-freq.h>
-#include <plat/clock.h>
-#include <plat/clock-clksrc.h>
-#include <plat/pll.h>
-
-#include "regs-sys.h"
-
-/* fin_apll, fin_mpll and fin_epll are all the same clock, which we call
- * ext_xtal_mux for want of an actual name from the manual.
-*/
-
-static struct clk clk_ext_xtal_mux = {
- .name = "ext_xtal",
-};
-
-#define clk_fin_apll clk_ext_xtal_mux
-#define clk_fin_mpll clk_ext_xtal_mux
-#define clk_fin_epll clk_ext_xtal_mux
-
-#define clk_fout_mpll clk_mpll
-#define clk_fout_epll clk_epll
-
-struct clk clk_h2 = {
- .name = "hclk2",
- .rate = 0,
-};
-
-struct clk clk_27m = {
- .name = "clk_27m",
- .rate = 27000000,
-};
-
-static int clk_48m_ctrl(struct clk *clk, int enable)
-{
- unsigned long flags;
- u32 val;
-
- /* can't rely on clock lock, this register has other usages */
- local_irq_save(flags);
-
- val = __raw_readl(S3C64XX_OTHERS);
- if (enable)
- val |= S3C64XX_OTHERS_USBMASK;
- else
- val &= ~S3C64XX_OTHERS_USBMASK;
-
- __raw_writel(val, S3C64XX_OTHERS);
- local_irq_restore(flags);
-
- return 0;
-}
-
-struct clk clk_48m = {
- .name = "clk_48m",
- .rate = 48000000,
- .enable = clk_48m_ctrl,
-};
-
-struct clk clk_xusbxti = {
- .name = "xusbxti",
- .rate = 48000000,
-};
-
-static int inline s3c64xx_gate(void __iomem *reg,
- struct clk *clk,
- int enable)
-{
- unsigned int ctrlbit = clk->ctrlbit;
- u32 con;
-
- con = __raw_readl(reg);
-
- if (enable)
- con |= ctrlbit;
- else
- con &= ~ctrlbit;
-
- __raw_writel(con, reg);
- return 0;
-}
-
-static int s3c64xx_pclk_ctrl(struct clk *clk, int enable)
-{
- return s3c64xx_gate(S3C_PCLK_GATE, clk, enable);
-}
-
-static int s3c64xx_hclk_ctrl(struct clk *clk, int enable)
-{
- return s3c64xx_gate(S3C_HCLK_GATE, clk, enable);
-}
-
-int s3c64xx_sclk_ctrl(struct clk *clk, int enable)
-{
- return s3c64xx_gate(S3C_SCLK_GATE, clk, enable);
-}
-
-static struct clk init_clocks_off[] = {
- {
- .name = "nand",
- .parent = &clk_h,
- }, {
- .name = "rtc",
- .parent = &clk_p,
- .enable = s3c64xx_pclk_ctrl,
- .ctrlbit = S3C_CLKCON_PCLK_RTC,
- }, {
- .name = "adc",
- .parent = &clk_p,
- .enable = s3c64xx_pclk_ctrl,
- .ctrlbit = S3C_CLKCON_PCLK_TSADC,
- }, {
- .name = "i2c",
- .devname = "s3c2440-i2c.0",
- .parent = &clk_p,
- .enable = s3c64xx_pclk_ctrl,
- .ctrlbit = S3C_CLKCON_PCLK_IIC,
- }, {
- .name = "i2c",
- .devname = "s3c2440-i2c.1",
- .parent = &clk_p,
- .enable = s3c64xx_pclk_ctrl,
- .ctrlbit = S3C6410_CLKCON_PCLK_I2C1,
- }, {
- .name = "keypad",
- .parent = &clk_p,
- .enable = s3c64xx_pclk_ctrl,
- .ctrlbit = S3C_CLKCON_PCLK_KEYPAD,
- }, {
- .name = "spi",
- .devname = "s3c6410-spi.0",
- .parent = &clk_p,
- .enable = s3c64xx_pclk_ctrl,
- .ctrlbit = S3C_CLKCON_PCLK_SPI0,
- }, {
- .name = "spi",
- .devname = "s3c6410-spi.1",
- .parent = &clk_p,
- .enable = s3c64xx_pclk_ctrl,
- .ctrlbit = S3C_CLKCON_PCLK_SPI1,
- }, {
- .name = "48m",
- .devname = "s3c-sdhci.0",
- .parent = &clk_48m,
- .enable = s3c64xx_sclk_ctrl,
- .ctrlbit = S3C_CLKCON_SCLK_MMC0_48,
- }, {
- .name = "48m",
- .devname = "s3c-sdhci.1",
- .parent = &clk_48m,
- .enable = s3c64xx_sclk_ctrl,
- .ctrlbit = S3C_CLKCON_SCLK_MMC1_48,
- }, {
- .name = "48m",
- .devname = "s3c-sdhci.2",
- .parent = &clk_48m,
- .enable = s3c64xx_sclk_ctrl,
- .ctrlbit = S3C_CLKCON_SCLK_MMC2_48,
- }, {
- .name = "ac97",
- .parent = &clk_p,
- .ctrlbit = S3C_CLKCON_PCLK_AC97,
- }, {
- .name = "cfcon",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_IHOST,
- }, {
- .name = "dma0",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_DMA0,
- }, {
- .name = "dma1",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_DMA1,
- }, {
- .name = "3dse",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_3DSE,
- }, {
- .name = "hclk_secur",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_SECUR,
- }, {
- .name = "sdma1",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_SDMA1,
- }, {
- .name = "sdma0",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_SDMA0,
- }, {
- .name = "hclk_jpeg",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_JPEG,
- }, {
- .name = "camif",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_CAMIF,
- }, {
- .name = "hclk_scaler",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_SCALER,
- }, {
- .name = "2d",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_2D,
- }, {
- .name = "tv",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_TV,
- }, {
- .name = "post0",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_POST0,
- }, {
- .name = "rot",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_ROT,
- }, {
- .name = "hclk_mfc",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_MFC,
- }, {
- .name = "pclk_mfc",
- .parent = &clk_p,
- .enable = s3c64xx_pclk_ctrl,
- .ctrlbit = S3C_CLKCON_PCLK_MFC,
- }, {
- .name = "dac27",
- .enable = s3c64xx_sclk_ctrl,
- .ctrlbit = S3C_CLKCON_SCLK_DAC27,
- }, {
- .name = "tv27",
- .enable = s3c64xx_sclk_ctrl,
- .ctrlbit = S3C_CLKCON_SCLK_TV27,
- }, {
- .name = "scaler27",
- .enable = s3c64xx_sclk_ctrl,
- .ctrlbit = S3C_CLKCON_SCLK_SCALER27,
- }, {
- .name = "sclk_scaler",
- .enable = s3c64xx_sclk_ctrl,
- .ctrlbit = S3C_CLKCON_SCLK_SCALER,
- }, {
- .name = "post0_27",
- .enable = s3c64xx_sclk_ctrl,
- .ctrlbit = S3C_CLKCON_SCLK_POST0_27,
- }, {
- .name = "secur",
- .enable = s3c64xx_sclk_ctrl,
- .ctrlbit = S3C_CLKCON_SCLK_SECUR,
- }, {
- .name = "sclk_mfc",
- .enable = s3c64xx_sclk_ctrl,
- .ctrlbit = S3C_CLKCON_SCLK_MFC,
- }, {
- .name = "sclk_jpeg",
- .enable = s3c64xx_sclk_ctrl,
- .ctrlbit = S3C_CLKCON_SCLK_JPEG,
- },
-};
-
-static struct clk clk_48m_spi0 = {
- .name = "spi_48m",
- .devname = "s3c6410-spi.0",
- .parent = &clk_48m,
- .enable = s3c64xx_sclk_ctrl,
- .ctrlbit = S3C_CLKCON_SCLK_SPI0_48,
-};
-
-static struct clk clk_48m_spi1 = {
- .name = "spi_48m",
- .devname = "s3c6410-spi.1",
- .parent = &clk_48m,
- .enable = s3c64xx_sclk_ctrl,
- .ctrlbit = S3C_CLKCON_SCLK_SPI1_48,
-};
-
-static struct clk clk_i2s0 = {
- .name = "iis",
- .devname = "samsung-i2s.0",
- .parent = &clk_p,
- .enable = s3c64xx_pclk_ctrl,
- .ctrlbit = S3C_CLKCON_PCLK_IIS0,
-};
-
-static struct clk clk_i2s1 = {
- .name = "iis",
- .devname = "samsung-i2s.1",
- .parent = &clk_p,
- .enable = s3c64xx_pclk_ctrl,
- .ctrlbit = S3C_CLKCON_PCLK_IIS1,
-};
-
-#ifdef CONFIG_CPU_S3C6410
-static struct clk clk_i2s2 = {
- .name = "iis",
- .devname = "samsung-i2s.2",
- .parent = &clk_p,
- .enable = s3c64xx_pclk_ctrl,
- .ctrlbit = S3C6410_CLKCON_PCLK_IIS2,
-};
-#endif
-
-static struct clk init_clocks[] = {
- {
- .name = "lcd",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_LCD,
- }, {
- .name = "gpio",
- .parent = &clk_p,
- .enable = s3c64xx_pclk_ctrl,
- .ctrlbit = S3C_CLKCON_PCLK_GPIO,
- }, {
- .name = "usb-host",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_UHOST,
- }, {
- .name = "otg",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_USB,
- }, {
- .name = "timers",
- .parent = &clk_p,
- .enable = s3c64xx_pclk_ctrl,
- .ctrlbit = S3C_CLKCON_PCLK_PWM,
- }, {
- .name = "uart",
- .devname = "s3c6400-uart.0",
- .parent = &clk_p,
- .enable = s3c64xx_pclk_ctrl,
- .ctrlbit = S3C_CLKCON_PCLK_UART0,
- }, {
- .name = "uart",
- .devname = "s3c6400-uart.1",
- .parent = &clk_p,
- .enable = s3c64xx_pclk_ctrl,
- .ctrlbit = S3C_CLKCON_PCLK_UART1,
- }, {
- .name = "uart",
- .devname = "s3c6400-uart.2",
- .parent = &clk_p,
- .enable = s3c64xx_pclk_ctrl,
- .ctrlbit = S3C_CLKCON_PCLK_UART2,
- }, {
- .name = "uart",
- .devname = "s3c6400-uart.3",
- .parent = &clk_p,
- .enable = s3c64xx_pclk_ctrl,
- .ctrlbit = S3C_CLKCON_PCLK_UART3,
- }, {
- .name = "watchdog",
- .parent = &clk_p,
- .ctrlbit = S3C_CLKCON_PCLK_WDT,
- },
-};
-
-static struct clk clk_hsmmc0 = {
- .name = "hsmmc",
- .devname = "s3c-sdhci.0",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_HSMMC0,
-};
-
-static struct clk clk_hsmmc1 = {
- .name = "hsmmc",
- .devname = "s3c-sdhci.1",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_HSMMC1,
-};
-
-static struct clk clk_hsmmc2 = {
- .name = "hsmmc",
- .devname = "s3c-sdhci.2",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_HSMMC2,
-};
-
-static struct clk clk_fout_apll = {
- .name = "fout_apll",
-};
-
-static struct clk *clk_src_apll_list[] = {
- [0] = &clk_fin_apll,
- [1] = &clk_fout_apll,
-};
-
-static struct clksrc_sources clk_src_apll = {
- .sources = clk_src_apll_list,
- .nr_sources = ARRAY_SIZE(clk_src_apll_list),
-};
-
-static struct clksrc_clk clk_mout_apll = {
- .clk = {
- .name = "mout_apll",
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 0, .size = 1 },
- .sources = &clk_src_apll,
-};
-
-static struct clk *clk_src_epll_list[] = {
- [0] = &clk_fin_epll,
- [1] = &clk_fout_epll,
-};
-
-static struct clksrc_sources clk_src_epll = {
- .sources = clk_src_epll_list,
- .nr_sources = ARRAY_SIZE(clk_src_epll_list),
-};
-
-static struct clksrc_clk clk_mout_epll = {
- .clk = {
- .name = "mout_epll",
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 2, .size = 1 },
- .sources = &clk_src_epll,
-};
-
-static struct clk *clk_src_mpll_list[] = {
- [0] = &clk_fin_mpll,
- [1] = &clk_fout_mpll,
-};
-
-static struct clksrc_sources clk_src_mpll = {
- .sources = clk_src_mpll_list,
- .nr_sources = ARRAY_SIZE(clk_src_mpll_list),
-};
-
-static struct clksrc_clk clk_mout_mpll = {
- .clk = {
- .name = "mout_mpll",
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 1, .size = 1 },
- .sources = &clk_src_mpll,
-};
-
-static unsigned int armclk_mask;
-
-static unsigned long s3c64xx_clk_arm_get_rate(struct clk *clk)
-{
- unsigned long rate = clk_get_rate(clk->parent);
- u32 clkdiv;
-
- /* divisor mask starts at bit0, so no need to shift */
- clkdiv = __raw_readl(S3C_CLK_DIV0) & armclk_mask;
-
- return rate / (clkdiv + 1);
-}
-
-static unsigned long s3c64xx_clk_arm_round_rate(struct clk *clk,
- unsigned long rate)
-{
- unsigned long parent = clk_get_rate(clk->parent);
- u32 div;
-
- if (parent < rate)
- return parent;
-
- div = (parent / rate) - 1;
- if (div > armclk_mask)
- div = armclk_mask;
-
- return parent / (div + 1);
-}
-
-static int s3c64xx_clk_arm_set_rate(struct clk *clk, unsigned long rate)
-{
- unsigned long parent = clk_get_rate(clk->parent);
- u32 div;
- u32 val;
-
- if (rate < parent / (armclk_mask + 1))
- return -EINVAL;
-
- rate = clk_round_rate(clk, rate);
- div = clk_get_rate(clk->parent) / rate;
-
- val = __raw_readl(S3C_CLK_DIV0);
- val &= ~armclk_mask;
- val |= (div - 1);
- __raw_writel(val, S3C_CLK_DIV0);
-
- return 0;
-
-}
-
-static struct clk clk_arm = {
- .name = "armclk",
- .parent = &clk_mout_apll.clk,
- .ops = &(struct clk_ops) {
- .get_rate = s3c64xx_clk_arm_get_rate,
- .set_rate = s3c64xx_clk_arm_set_rate,
- .round_rate = s3c64xx_clk_arm_round_rate,
- },
-};
-
-static unsigned long s3c64xx_clk_doutmpll_get_rate(struct clk *clk)
-{
- unsigned long rate = clk_get_rate(clk->parent);
-
- printk(KERN_DEBUG "%s: parent is %ld\n", __func__, rate);
-
- if (__raw_readl(S3C_CLK_DIV0) & S3C6400_CLKDIV0_MPLL_MASK)
- rate /= 2;
-
- return rate;
-}
-
-static struct clk_ops clk_dout_ops = {
- .get_rate = s3c64xx_clk_doutmpll_get_rate,
-};
-
-static struct clk clk_dout_mpll = {
- .name = "dout_mpll",
- .parent = &clk_mout_mpll.clk,
- .ops = &clk_dout_ops,
-};
-
-static struct clk *clkset_spi_mmc_list[] = {
- &clk_mout_epll.clk,
- &clk_dout_mpll,
- &clk_fin_epll,
- &clk_27m,
-};
-
-static struct clksrc_sources clkset_spi_mmc = {
- .sources = clkset_spi_mmc_list,
- .nr_sources = ARRAY_SIZE(clkset_spi_mmc_list),
-};
-
-static struct clk *clkset_irda_list[] = {
- &clk_mout_epll.clk,
- &clk_dout_mpll,
- NULL,
- &clk_27m,
-};
-
-static struct clksrc_sources clkset_irda = {
- .sources = clkset_irda_list,
- .nr_sources = ARRAY_SIZE(clkset_irda_list),
-};
-
-static struct clk *clkset_uart_list[] = {
- &clk_mout_epll.clk,
- &clk_dout_mpll,
- NULL,
- NULL
-};
-
-static struct clksrc_sources clkset_uart = {
- .sources = clkset_uart_list,
- .nr_sources = ARRAY_SIZE(clkset_uart_list),
-};
-
-static struct clk *clkset_uhost_list[] = {
- &clk_48m,
- &clk_mout_epll.clk,
- &clk_dout_mpll,
- &clk_fin_epll,
-};
-
-static struct clksrc_sources clkset_uhost = {
- .sources = clkset_uhost_list,
- .nr_sources = ARRAY_SIZE(clkset_uhost_list),
-};
-
-/* The peripheral clocks are all controlled via clocksource followed
- * by an optional divider and gate stage. We currently roll this into
- * one clock which hides the intermediate clock from the mux.
- *
- * Note, the JPEG clock can only be an even divider...
- *
- * The scaler and LCD clocks depend on the S3C64XX version, and also
- * have a common parent divisor so are not included here.
- */
-
-/* clocks that feed other parts of the clock source tree */
-
-static struct clk clk_iis_cd0 = {
- .name = "iis_cdclk0",
-};
-
-static struct clk clk_iis_cd1 = {
- .name = "iis_cdclk1",
-};
-
-static struct clk clk_iisv4_cd = {
- .name = "iis_cdclk_v4",
-};
-
-static struct clk clk_pcm_cd = {
- .name = "pcm_cdclk",
-};
-
-static struct clk *clkset_audio0_list[] = {
- [0] = &clk_mout_epll.clk,
- [1] = &clk_dout_mpll,
- [2] = &clk_fin_epll,
- [3] = &clk_iis_cd0,
- [4] = &clk_pcm_cd,
-};
-
-static struct clksrc_sources clkset_audio0 = {
- .sources = clkset_audio0_list,
- .nr_sources = ARRAY_SIZE(clkset_audio0_list),
-};
-
-static struct clk *clkset_audio1_list[] = {
- [0] = &clk_mout_epll.clk,
- [1] = &clk_dout_mpll,
- [2] = &clk_fin_epll,
- [3] = &clk_iis_cd1,
- [4] = &clk_pcm_cd,
-};
-
-static struct clksrc_sources clkset_audio1 = {
- .sources = clkset_audio1_list,
- .nr_sources = ARRAY_SIZE(clkset_audio1_list),
-};
-
-#ifdef CONFIG_CPU_S3C6410
-static struct clk *clkset_audio2_list[] = {
- [0] = &clk_mout_epll.clk,
- [1] = &clk_dout_mpll,
- [2] = &clk_fin_epll,
- [3] = &clk_iisv4_cd,
- [4] = &clk_pcm_cd,
-};
-
-static struct clksrc_sources clkset_audio2 = {
- .sources = clkset_audio2_list,
- .nr_sources = ARRAY_SIZE(clkset_audio2_list),
-};
-#endif
-
-static struct clksrc_clk clksrcs[] = {
- {
- .clk = {
- .name = "usb-bus-host",
- .ctrlbit = S3C_CLKCON_SCLK_UHOST,
- .enable = s3c64xx_sclk_ctrl,
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 5, .size = 2 },
- .reg_div = { .reg = S3C_CLK_DIV1, .shift = 20, .size = 4 },
- .sources = &clkset_uhost,
- }, {
- .clk = {
- .name = "irda-bus",
- .ctrlbit = S3C_CLKCON_SCLK_IRDA,
- .enable = s3c64xx_sclk_ctrl,
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 24, .size = 2 },
- .reg_div = { .reg = S3C_CLK_DIV2, .shift = 20, .size = 4 },
- .sources = &clkset_irda,
- }, {
- .clk = {
- .name = "camera",
- .ctrlbit = S3C_CLKCON_SCLK_CAM,
- .enable = s3c64xx_sclk_ctrl,
- .parent = &clk_h2,
- },
- .reg_div = { .reg = S3C_CLK_DIV0, .shift = 20, .size = 4 },
- },
-};
-
-/* Where does UCLK0 come from? */
-static struct clksrc_clk clk_sclk_uclk = {
- .clk = {
- .name = "uclk1",
- .ctrlbit = S3C_CLKCON_SCLK_UART,
- .enable = s3c64xx_sclk_ctrl,
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 13, .size = 1 },
- .reg_div = { .reg = S3C_CLK_DIV2, .shift = 16, .size = 4 },
- .sources = &clkset_uart,
-};
-
-static struct clksrc_clk clk_sclk_mmc0 = {
- .clk = {
- .name = "mmc_bus",
- .devname = "s3c-sdhci.0",
- .ctrlbit = S3C_CLKCON_SCLK_MMC0,
- .enable = s3c64xx_sclk_ctrl,
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 18, .size = 2 },
- .reg_div = { .reg = S3C_CLK_DIV1, .shift = 0, .size = 4 },
- .sources = &clkset_spi_mmc,
-};
-
-static struct clksrc_clk clk_sclk_mmc1 = {
- .clk = {
- .name = "mmc_bus",
- .devname = "s3c-sdhci.1",
- .ctrlbit = S3C_CLKCON_SCLK_MMC1,
- .enable = s3c64xx_sclk_ctrl,
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 20, .size = 2 },
- .reg_div = { .reg = S3C_CLK_DIV1, .shift = 4, .size = 4 },
- .sources = &clkset_spi_mmc,
-};
-
-static struct clksrc_clk clk_sclk_mmc2 = {
- .clk = {
- .name = "mmc_bus",
- .devname = "s3c-sdhci.2",
- .ctrlbit = S3C_CLKCON_SCLK_MMC2,
- .enable = s3c64xx_sclk_ctrl,
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 22, .size = 2 },
- .reg_div = { .reg = S3C_CLK_DIV1, .shift = 8, .size = 4 },
- .sources = &clkset_spi_mmc,
-};
-
-static struct clksrc_clk clk_sclk_spi0 = {
- .clk = {
- .name = "spi-bus",
- .devname = "s3c6410-spi.0",
- .ctrlbit = S3C_CLKCON_SCLK_SPI0,
- .enable = s3c64xx_sclk_ctrl,
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 14, .size = 2 },
- .reg_div = { .reg = S3C_CLK_DIV2, .shift = 0, .size = 4 },
- .sources = &clkset_spi_mmc,
-};
-
-static struct clksrc_clk clk_sclk_spi1 = {
- .clk = {
- .name = "spi-bus",
- .devname = "s3c6410-spi.1",
- .ctrlbit = S3C_CLKCON_SCLK_SPI1,
- .enable = s3c64xx_sclk_ctrl,
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 16, .size = 2 },
- .reg_div = { .reg = S3C_CLK_DIV2, .shift = 4, .size = 4 },
- .sources = &clkset_spi_mmc,
-};
-
-static struct clksrc_clk clk_audio_bus0 = {
- .clk = {
- .name = "audio-bus",
- .devname = "samsung-i2s.0",
- .ctrlbit = S3C_CLKCON_SCLK_AUDIO0,
- .enable = s3c64xx_sclk_ctrl,
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 7, .size = 3 },
- .reg_div = { .reg = S3C_CLK_DIV2, .shift = 8, .size = 4 },
- .sources = &clkset_audio0,
-};
-
-static struct clksrc_clk clk_audio_bus1 = {
- .clk = {
- .name = "audio-bus",
- .devname = "samsung-i2s.1",
- .ctrlbit = S3C_CLKCON_SCLK_AUDIO1,
- .enable = s3c64xx_sclk_ctrl,
- },
- .reg_src = { .reg = S3C_CLK_SRC, .shift = 10, .size = 3 },
- .reg_div = { .reg = S3C_CLK_DIV2, .shift = 12, .size = 4 },
- .sources = &clkset_audio1,
-};
-
-#ifdef CONFIG_CPU_S3C6410
-static struct clksrc_clk clk_audio_bus2 = {
- .clk = {
- .name = "audio-bus",
- .devname = "samsung-i2s.2",
- .ctrlbit = S3C6410_CLKCON_SCLK_AUDIO2,
- .enable = s3c64xx_sclk_ctrl,
- },
- .reg_src = { .reg = S3C6410_CLK_SRC2, .shift = 0, .size = 3 },
- .reg_div = { .reg = S3C_CLK_DIV2, .shift = 24, .size = 4 },
- .sources = &clkset_audio2,
-};
-#endif
-/* Clock initialisation code */
-
-static struct clksrc_clk *init_parents[] = {
- &clk_mout_apll,
- &clk_mout_epll,
- &clk_mout_mpll,
-};
-
-static struct clksrc_clk *clksrc_cdev[] = {
- &clk_sclk_uclk,
- &clk_sclk_mmc0,
- &clk_sclk_mmc1,
- &clk_sclk_mmc2,
- &clk_sclk_spi0,
- &clk_sclk_spi1,
- &clk_audio_bus0,
- &clk_audio_bus1,
-};
-
-static struct clk *clk_cdev[] = {
- &clk_hsmmc0,
- &clk_hsmmc1,
- &clk_hsmmc2,
- &clk_48m_spi0,
- &clk_48m_spi1,
- &clk_i2s0,
- &clk_i2s1,
-};
-
-static struct clk_lookup s3c64xx_clk_lookup[] = {
- CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_p),
- CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_sclk_uclk.clk),
- CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.0", &clk_hsmmc0),
- CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.0", &clk_hsmmc1),
- CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.0", &clk_hsmmc2),
- CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.2", &clk_sclk_mmc0.clk),
- CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_sclk_mmc1.clk),
- CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.2", &clk_sclk_mmc2.clk),
- CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
- CLKDEV_INIT("s3c6410-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
- CLKDEV_INIT("s3c6410-spi.0", "spi_busclk2", &clk_48m_spi0),
- CLKDEV_INIT("s3c6410-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
- CLKDEV_INIT("s3c6410-spi.1", "spi_busclk2", &clk_48m_spi1),
- CLKDEV_INIT("samsung-i2s.0", "i2s_opclk0", &clk_i2s0),
- CLKDEV_INIT("samsung-i2s.0", "i2s_opclk1", &clk_audio_bus0.clk),
- CLKDEV_INIT("samsung-i2s.1", "i2s_opclk0", &clk_i2s1),
- CLKDEV_INIT("samsung-i2s.1", "i2s_opclk1", &clk_audio_bus1.clk),
-#ifdef CONFIG_CPU_S3C6410
- CLKDEV_INIT("samsung-i2s.2", "i2s_opclk0", &clk_i2s2),
- CLKDEV_INIT("samsung-i2s.2", "i2s_opclk1", &clk_audio_bus2.clk),
-#endif
-};
-
-#define GET_DIV(clk, field) ((((clk) & field##_MASK) >> field##_SHIFT) + 1)
-
-void __init_or_cpufreq s3c64xx_setup_clocks(void)
-{
- struct clk *xtal_clk;
- unsigned long xtal;
- unsigned long fclk;
- unsigned long hclk;
- unsigned long hclk2;
- unsigned long pclk;
- unsigned long epll;
- unsigned long apll;
- unsigned long mpll;
- unsigned int ptr;
- u32 clkdiv0;
-
- printk(KERN_DEBUG "%s: registering clocks\n", __func__);
-
- clkdiv0 = __raw_readl(S3C_CLK_DIV0);
- printk(KERN_DEBUG "%s: clkdiv0 = %08x\n", __func__, clkdiv0);
-
- xtal_clk = clk_get(NULL, "xtal");
- BUG_ON(IS_ERR(xtal_clk));
-
- xtal = clk_get_rate(xtal_clk);
- clk_put(xtal_clk);
-
- printk(KERN_DEBUG "%s: xtal is %ld\n", __func__, xtal);
-
- /* For now assume the mux always selects the crystal */
- clk_ext_xtal_mux.parent = xtal_clk;
-
- epll = s3c_get_pll6553x(xtal, __raw_readl(S3C_EPLL_CON0),
- __raw_readl(S3C_EPLL_CON1));
- mpll = s3c6400_get_pll(xtal, __raw_readl(S3C_MPLL_CON));
- apll = s3c6400_get_pll(xtal, __raw_readl(S3C_APLL_CON));
-
- fclk = mpll;
-
- printk(KERN_INFO "S3C64XX: PLL settings, A=%ld, M=%ld, E=%ld\n",
- apll, mpll, epll);
-
- if(__raw_readl(S3C64XX_OTHERS) & S3C64XX_OTHERS_SYNCMUXSEL)
- /* Synchronous mode */
- hclk2 = apll / GET_DIV(clkdiv0, S3C6400_CLKDIV0_HCLK2);
- else
- /* Asynchronous mode */
- hclk2 = mpll / GET_DIV(clkdiv0, S3C6400_CLKDIV0_HCLK2);
-
- hclk = hclk2 / GET_DIV(clkdiv0, S3C6400_CLKDIV0_HCLK);
- pclk = hclk2 / GET_DIV(clkdiv0, S3C6400_CLKDIV0_PCLK);
-
- printk(KERN_INFO "S3C64XX: HCLK2=%ld, HCLK=%ld, PCLK=%ld\n",
- hclk2, hclk, pclk);
-
- clk_fout_mpll.rate = mpll;
- clk_fout_epll.rate = epll;
- clk_fout_apll.rate = apll;
-
- clk_h2.rate = hclk2;
- clk_h.rate = hclk;
- clk_p.rate = pclk;
- clk_f.rate = fclk;
-
- for (ptr = 0; ptr < ARRAY_SIZE(init_parents); ptr++)
- s3c_set_clksrc(init_parents[ptr], true);
-
- for (ptr = 0; ptr < ARRAY_SIZE(clksrcs); ptr++)
- s3c_set_clksrc(&clksrcs[ptr], true);
-}
-
-static struct clk *clks1[] __initdata = {
- &clk_ext_xtal_mux,
- &clk_iis_cd0,
- &clk_iis_cd1,
- &clk_iisv4_cd,
- &clk_pcm_cd,
- &clk_mout_epll.clk,
- &clk_mout_mpll.clk,
- &clk_dout_mpll,
- &clk_arm,
-};
-
-static struct clk *clks[] __initdata = {
- &clk_ext,
- &clk_epll,
- &clk_27m,
- &clk_48m,
- &clk_h2,
- &clk_xusbxti,
-};
-
-/**
- * s3c64xx_register_clocks - register clocks for s3c6400 and s3c6410
- * @xtal: The rate for the clock crystal feeding the PLLs.
- * @armclk_divlimit: Divisor mask for ARMCLK.
- *
- * Register the clocks for the S3C6400 and S3C6410 SoC range, such
- * as ARMCLK as well as the necessary parent clocks.
- *
- * This call does not setup the clocks, which is left to the
- * s3c64xx_setup_clocks() call which may be needed by the cpufreq
- * or resume code to re-set the clocks if the bootloader has changed
- * them.
- */
-void __init s3c64xx_register_clocks(unsigned long xtal,
- unsigned armclk_divlimit)
-{
- unsigned int cnt;
-
- armclk_mask = armclk_divlimit;
-
- s3c24xx_register_baseclocks(xtal);
- s3c24xx_register_clocks(clks, ARRAY_SIZE(clks));
-
- s3c_register_clocks(init_clocks, ARRAY_SIZE(init_clocks));
-
- s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
- s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
-
- s3c24xx_register_clocks(clk_cdev, ARRAY_SIZE(clk_cdev));
- for (cnt = 0; cnt < ARRAY_SIZE(clk_cdev); cnt++)
- s3c_disable_clocks(clk_cdev[cnt], 1);
-
- s3c24xx_register_clocks(clks1, ARRAY_SIZE(clks1));
- s3c_register_clksrc(clksrcs, ARRAY_SIZE(clksrcs));
- for (cnt = 0; cnt < ARRAY_SIZE(clksrc_cdev); cnt++)
- s3c_register_clksrc(clksrc_cdev[cnt], 1);
- clkdev_add_table(s3c64xx_clk_lookup, ARRAY_SIZE(s3c64xx_clk_lookup));
-}
diff --git a/arch/arm/mach-s3c64xx/common.c b/arch/arm/mach-s3c64xx/common.c
index 73d79cf..7a3ce4c 100644
--- a/arch/arm/mach-s3c64xx/common.c
+++ b/arch/arm/mach-s3c64xx/common.c
@@ -14,9 +14,14 @@
* published by the Free Software Foundation.
*/
+/*
+ * NOTE: Code in this file is not used when booting with Device Tree support.
+ */
+
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/module.h>
+#include <linux/clk-provider.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
#include <linux/serial_core.h>
@@ -38,7 +43,6 @@
#include <mach/regs-gpio.h>
#include <plat/cpu.h>
-#include <plat/clock.h>
#include <plat/devs.h>
#include <plat/pm.h>
#include <plat/gpio-cfg.h>
@@ -50,6 +54,19 @@
#include "common.h"
+/* External clock frequency */
+static unsigned long xtal_f = 12000000, xusbxti_f = 48000000;
+
+void __init s3c64xx_set_xtal_freq(unsigned long freq)
+{
+ xtal_f = freq;
+}
+
+void __init s3c64xx_set_xusbxti_freq(unsigned long freq)
+{
+ xusbxti_f = freq;
+}
+
/* uart registration process */
static void __init s3c64xx_init_uarts(struct s3c2410_uartcfg *cfg, int no)
@@ -67,7 +84,6 @@
.idcode = S3C6400_CPU_ID,
.idmask = S3C64XX_CPU_MASK,
.map_io = s3c6400_map_io,
- .init_clocks = s3c6400_init_clocks,
.init_uarts = s3c64xx_init_uarts,
.init = s3c6400_init,
.name = name_s3c6400,
@@ -75,7 +91,6 @@
.idcode = S3C6410_CPU_ID,
.idmask = S3C64XX_CPU_MASK,
.map_io = s3c6410_map_io,
- .init_clocks = s3c6410_init_clocks,
.init_uarts = s3c64xx_init_uarts,
.init = s3c6410_init,
.name = name_s3c6410,
@@ -192,6 +207,10 @@
static __init int s3c64xx_dev_init(void)
{
+ /* Not applicable when using DT. */
+ if (of_have_populated_dt())
+ return 0;
+
subsys_system_register(&s3c64xx_subsys, NULL);
return device_register(&s3c64xx_dev);
}
@@ -213,8 +232,10 @@
{
/*
* FIXME: there is no better place to put this at the moment
- * (samsung_wdt_reset_init needs clocks)
+ * (s3c64xx_clk_init needs ioremap and must happen before init_time
+ * samsung_wdt_reset_init needs clocks)
*/
+ s3c64xx_clk_init(NULL, xtal_f, xusbxti_f, soc_is_s3c6400(), S3C_VA_SYS);
samsung_wdt_reset_init(S3C_VA_WATCHDOG);
printk(KERN_DEBUG "%s: initialising interrupts\n", __func__);
@@ -391,6 +412,10 @@
{
int irq;
+ /* On DT-enabled systems EINTs are handled by pinctrl-s3c64xx driver. */
+ if (of_have_populated_dt())
+ return -ENODEV;
+
for (irq = IRQ_EINT(0); irq <= IRQ_EINT(27); irq++) {
irq_set_chip_and_handler(irq, &s3c_irq_eint, handle_level_irq);
irq_set_chip_data(irq, (void *)eint_irq_to_bit(irq));
diff --git a/arch/arm/mach-s3c64xx/common.h b/arch/arm/mach-s3c64xx/common.h
index e8f990b..bd3bd56 100644
--- a/arch/arm/mach-s3c64xx/common.h
+++ b/arch/arm/mach-s3c64xx/common.h
@@ -22,21 +22,21 @@
void s3c64xx_init_irq(u32 vic0, u32 vic1);
void s3c64xx_init_io(struct map_desc *mach_desc, int size);
-void s3c64xx_register_clocks(unsigned long xtal, unsigned armclk_limit);
-void s3c64xx_setup_clocks(void);
-
void s3c64xx_restart(enum reboot_mode mode, const char *cmd);
void s3c64xx_init_late(void);
+void s3c64xx_clk_init(struct device_node *np, unsigned long xtal_f,
+ unsigned long xusbxti_f, bool is_s3c6400, void __iomem *reg_base);
+void s3c64xx_set_xtal_freq(unsigned long freq);
+void s3c64xx_set_xusbxti_freq(unsigned long freq);
+
#ifdef CONFIG_CPU_S3C6400
extern int s3c6400_init(void);
extern void s3c6400_init_irq(void);
extern void s3c6400_map_io(void);
-extern void s3c6400_init_clocks(int xtal);
#else
-#define s3c6400_init_clocks NULL
#define s3c6400_map_io NULL
#define s3c6400_init NULL
#endif
@@ -46,10 +46,8 @@
extern int s3c6410_init(void);
extern void s3c6410_init_irq(void);
extern void s3c6410_map_io(void);
-extern void s3c6410_init_clocks(int xtal);
#else
-#define s3c6410_init_clocks NULL
#define s3c6410_map_io NULL
#define s3c6410_init NULL
#endif
diff --git a/arch/arm/mach-s3c64xx/dma.c b/arch/arm/mach-s3c64xx/dma.c
index 759846c..7e22c21 100644
--- a/arch/arm/mach-s3c64xx/dma.c
+++ b/arch/arm/mach-s3c64xx/dma.c
@@ -12,6 +12,10 @@
* published by the Free Software Foundation.
*/
+/*
+ * NOTE: Code in this file is not used when booting with Device Tree support.
+ */
+
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/interrupt.h>
@@ -24,6 +28,7 @@
#include <linux/err.h>
#include <linux/io.h>
#include <linux/amba/pl080.h>
+#include <linux/of.h>
#include <mach/dma.h>
#include <mach/map.h>
@@ -677,7 +682,7 @@
goto err_map;
}
- clk_enable(dmac->clk);
+ clk_prepare_enable(dmac->clk);
dmac->regs = regs;
dmac->chanbase = chbase;
@@ -711,7 +716,7 @@
return 0;
err_clk:
- clk_disable(dmac->clk);
+ clk_disable_unprepare(dmac->clk);
clk_put(dmac->clk);
err_map:
iounmap(regs);
@@ -726,6 +731,10 @@
{
int ret;
+ /* This driver is not supported when booting with device tree. */
+ if (of_have_populated_dt())
+ return -ENODEV;
+
printk(KERN_INFO "%s: Registering DMA channels\n", __func__);
dma_pool = dma_pool_create("DMA-LLI", NULL, sizeof(struct pl080s_lli), 16, 0);
diff --git a/arch/arm/mach-s3c64xx/include/mach/regs-clock.h b/arch/arm/mach-s3c64xx/include/mach/regs-clock.h
index 05332b9..4f44aac 100644
--- a/arch/arm/mach-s3c64xx/include/mach/regs-clock.h
+++ b/arch/arm/mach-s3c64xx/include/mach/regs-clock.h
@@ -15,145 +15,21 @@
#ifndef __PLAT_REGS_CLOCK_H
#define __PLAT_REGS_CLOCK_H __FILE__
+/*
+ * FIXME: Remove remaining definitions
+ */
+
#define S3C_CLKREG(x) (S3C_VA_SYS + (x))
-#define S3C_APLL_LOCK S3C_CLKREG(0x00)
-#define S3C_MPLL_LOCK S3C_CLKREG(0x04)
-#define S3C_EPLL_LOCK S3C_CLKREG(0x08)
-#define S3C_APLL_CON S3C_CLKREG(0x0C)
-#define S3C_MPLL_CON S3C_CLKREG(0x10)
-#define S3C_EPLL_CON0 S3C_CLKREG(0x14)
-#define S3C_EPLL_CON1 S3C_CLKREG(0x18)
-#define S3C_CLK_SRC S3C_CLKREG(0x1C)
-#define S3C_CLK_DIV0 S3C_CLKREG(0x20)
-#define S3C_CLK_DIV1 S3C_CLKREG(0x24)
-#define S3C_CLK_DIV2 S3C_CLKREG(0x28)
-#define S3C_CLK_OUT S3C_CLKREG(0x2C)
-#define S3C_HCLK_GATE S3C_CLKREG(0x30)
#define S3C_PCLK_GATE S3C_CLKREG(0x34)
-#define S3C_SCLK_GATE S3C_CLKREG(0x38)
-#define S3C_MEM0_GATE S3C_CLKREG(0x3C)
#define S3C6410_CLK_SRC2 S3C_CLKREG(0x10C)
#define S3C_MEM_SYS_CFG S3C_CLKREG(0x120)
-/* CLKDIV0 */
-#define S3C6400_CLKDIV0_PCLK_MASK (0xf << 12)
-#define S3C6400_CLKDIV0_PCLK_SHIFT (12)
-#define S3C6400_CLKDIV0_HCLK2_MASK (0x7 << 9)
-#define S3C6400_CLKDIV0_HCLK2_SHIFT (9)
-#define S3C6400_CLKDIV0_HCLK_MASK (0x1 << 8)
-#define S3C6400_CLKDIV0_HCLK_SHIFT (8)
-#define S3C6400_CLKDIV0_MPLL_MASK (0x1 << 4)
-#define S3C6400_CLKDIV0_MPLL_SHIFT (4)
-
-#define S3C6400_CLKDIV0_ARM_MASK (0x7 << 0)
-#define S3C6410_CLKDIV0_ARM_MASK (0xf << 0)
-#define S3C6400_CLKDIV0_ARM_SHIFT (0)
-
-/* HCLK GATE Registers */
-#define S3C_CLKCON_HCLK_3DSE (1<<31)
-#define S3C_CLKCON_HCLK_UHOST (1<<29)
-#define S3C_CLKCON_HCLK_SECUR (1<<28)
-#define S3C_CLKCON_HCLK_SDMA1 (1<<27)
-#define S3C_CLKCON_HCLK_SDMA0 (1<<26)
-#define S3C_CLKCON_HCLK_IROM (1<<25)
-#define S3C_CLKCON_HCLK_DDR1 (1<<24)
-#define S3C_CLKCON_HCLK_DDR0 (1<<23)
-#define S3C_CLKCON_HCLK_MEM1 (1<<22)
-#define S3C_CLKCON_HCLK_MEM0 (1<<21)
-#define S3C_CLKCON_HCLK_USB (1<<20)
-#define S3C_CLKCON_HCLK_HSMMC2 (1<<19)
-#define S3C_CLKCON_HCLK_HSMMC1 (1<<18)
-#define S3C_CLKCON_HCLK_HSMMC0 (1<<17)
-#define S3C_CLKCON_HCLK_MDP (1<<16)
-#define S3C_CLKCON_HCLK_DHOST (1<<15)
-#define S3C_CLKCON_HCLK_IHOST (1<<14)
-#define S3C_CLKCON_HCLK_DMA1 (1<<13)
-#define S3C_CLKCON_HCLK_DMA0 (1<<12)
-#define S3C_CLKCON_HCLK_JPEG (1<<11)
-#define S3C_CLKCON_HCLK_CAMIF (1<<10)
-#define S3C_CLKCON_HCLK_SCALER (1<<9)
-#define S3C_CLKCON_HCLK_2D (1<<8)
-#define S3C_CLKCON_HCLK_TV (1<<7)
-#define S3C_CLKCON_HCLK_POST0 (1<<5)
-#define S3C_CLKCON_HCLK_ROT (1<<4)
-#define S3C_CLKCON_HCLK_LCD (1<<3)
-#define S3C_CLKCON_HCLK_TZIC (1<<2)
-#define S3C_CLKCON_HCLK_INTC (1<<1)
-#define S3C_CLKCON_HCLK_MFC (1<<0)
-
/* PCLK GATE Registers */
-#define S3C6410_CLKCON_PCLK_I2C1 (1<<27)
-#define S3C6410_CLKCON_PCLK_IIS2 (1<<26)
-#define S3C_CLKCON_PCLK_SKEY (1<<24)
-#define S3C_CLKCON_PCLK_CHIPID (1<<23)
-#define S3C_CLKCON_PCLK_SPI1 (1<<22)
-#define S3C_CLKCON_PCLK_SPI0 (1<<21)
-#define S3C_CLKCON_PCLK_HSIRX (1<<20)
-#define S3C_CLKCON_PCLK_HSITX (1<<19)
-#define S3C_CLKCON_PCLK_GPIO (1<<18)
-#define S3C_CLKCON_PCLK_IIC (1<<17)
-#define S3C_CLKCON_PCLK_IIS1 (1<<16)
-#define S3C_CLKCON_PCLK_IIS0 (1<<15)
-#define S3C_CLKCON_PCLK_AC97 (1<<14)
-#define S3C_CLKCON_PCLK_TZPC (1<<13)
-#define S3C_CLKCON_PCLK_TSADC (1<<12)
-#define S3C_CLKCON_PCLK_KEYPAD (1<<11)
-#define S3C_CLKCON_PCLK_IRDA (1<<10)
-#define S3C_CLKCON_PCLK_PCM1 (1<<9)
-#define S3C_CLKCON_PCLK_PCM0 (1<<8)
-#define S3C_CLKCON_PCLK_PWM (1<<7)
-#define S3C_CLKCON_PCLK_RTC (1<<6)
-#define S3C_CLKCON_PCLK_WDT (1<<5)
#define S3C_CLKCON_PCLK_UART3 (1<<4)
#define S3C_CLKCON_PCLK_UART2 (1<<3)
#define S3C_CLKCON_PCLK_UART1 (1<<2)
#define S3C_CLKCON_PCLK_UART0 (1<<1)
-#define S3C_CLKCON_PCLK_MFC (1<<0)
-
-/* SCLK GATE Registers */
-#define S3C_CLKCON_SCLK_UHOST (1<<30)
-#define S3C_CLKCON_SCLK_MMC2_48 (1<<29)
-#define S3C_CLKCON_SCLK_MMC1_48 (1<<28)
-#define S3C_CLKCON_SCLK_MMC0_48 (1<<27)
-#define S3C_CLKCON_SCLK_MMC2 (1<<26)
-#define S3C_CLKCON_SCLK_MMC1 (1<<25)
-#define S3C_CLKCON_SCLK_MMC0 (1<<24)
-#define S3C_CLKCON_SCLK_SPI1_48 (1<<23)
-#define S3C_CLKCON_SCLK_SPI0_48 (1<<22)
-#define S3C_CLKCON_SCLK_SPI1 (1<<21)
-#define S3C_CLKCON_SCLK_SPI0 (1<<20)
-#define S3C_CLKCON_SCLK_DAC27 (1<<19)
-#define S3C_CLKCON_SCLK_TV27 (1<<18)
-#define S3C_CLKCON_SCLK_SCALER27 (1<<17)
-#define S3C_CLKCON_SCLK_SCALER (1<<16)
-#define S3C_CLKCON_SCLK_LCD27 (1<<15)
-#define S3C_CLKCON_SCLK_LCD (1<<14)
-#define S3C6400_CLKCON_SCLK_POST1_27 (1<<13)
-#define S3C6410_CLKCON_FIMC (1<<13)
-#define S3C_CLKCON_SCLK_POST0_27 (1<<12)
-#define S3C6400_CLKCON_SCLK_POST1 (1<<11)
-#define S3C6410_CLKCON_SCLK_AUDIO2 (1<<11)
-#define S3C_CLKCON_SCLK_POST0 (1<<10)
-#define S3C_CLKCON_SCLK_AUDIO1 (1<<9)
-#define S3C_CLKCON_SCLK_AUDIO0 (1<<8)
-#define S3C_CLKCON_SCLK_SECUR (1<<7)
-#define S3C_CLKCON_SCLK_IRDA (1<<6)
-#define S3C_CLKCON_SCLK_UART (1<<5)
-#define S3C_CLKCON_SCLK_ONENAND (1<<4)
-#define S3C_CLKCON_SCLK_MFC (1<<3)
-#define S3C_CLKCON_SCLK_CAM (1<<2)
-#define S3C_CLKCON_SCLK_JPEG (1<<1)
-
-/* CLKSRC */
-
-#define S3C6400_CLKSRC_APLL_MOUT (1 << 0)
-#define S3C6400_CLKSRC_MPLL_MOUT (1 << 1)
-#define S3C6400_CLKSRC_EPLL_MOUT (1 << 2)
-#define S3C6400_CLKSRC_APLL_MOUT_SHIFT (0)
-#define S3C6400_CLKSRC_MPLL_MOUT_SHIFT (1)
-#define S3C6400_CLKSRC_EPLL_MOUT_SHIFT (2)
-#define S3C6400_CLKSRC_MFC (1 << 4)
/* MEM_SYS_CFG */
#define MEM_SYS_CFG_INDEP_CF 0x4000
diff --git a/arch/arm/mach-s3c64xx/irq-pm.c b/arch/arm/mach-s3c64xx/irq-pm.c
index c3da1b6..1649c0d 100644
--- a/arch/arm/mach-s3c64xx/irq-pm.c
+++ b/arch/arm/mach-s3c64xx/irq-pm.c
@@ -12,12 +12,17 @@
* published by the Free Software Foundation.
*/
+/*
+ * NOTE: Code in this file is not used when booting with Device Tree support.
+ */
+
#include <linux/kernel.h>
#include <linux/syscore_ops.h>
#include <linux/interrupt.h>
#include <linux/serial_core.h>
#include <linux/irq.h>
#include <linux/io.h>
+#include <linux/of.h>
#include <mach/map.h>
@@ -101,6 +106,10 @@
static __init int s3c64xx_syscore_init(void)
{
+ /* Appropriate drivers (pinctrl, uart) handle this when using DT. */
+ if (of_have_populated_dt())
+ return 0;
+
register_syscore_ops(&s3c64xx_irq_syscore_ops);
return 0;
diff --git a/arch/arm/mach-s3c64xx/mach-anw6410.c b/arch/arm/mach-s3c64xx/mach-anw6410.c
index 35e3f54..d266dd5 100644
--- a/arch/arm/mach-s3c64xx/mach-anw6410.c
+++ b/arch/arm/mach-s3c64xx/mach-anw6410.c
@@ -207,7 +207,7 @@
static void __init anw6410_map_io(void)
{
s3c64xx_init_io(anw6410_iodesc, ARRAY_SIZE(anw6410_iodesc));
- s3c24xx_init_clocks(12000000);
+ s3c64xx_set_xtal_freq(12000000);
s3c24xx_init_uarts(anw6410_uartcfgs, ARRAY_SIZE(anw6410_uartcfgs));
samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
diff --git a/arch/arm/mach-s3c64xx/mach-crag6410.c b/arch/arm/mach-s3c64xx/mach-crag6410.c
index eb8e5a1..1a911df 100644
--- a/arch/arm/mach-s3c64xx/mach-crag6410.c
+++ b/arch/arm/mach-s3c64xx/mach-crag6410.c
@@ -743,7 +743,7 @@
static void __init crag6410_map_io(void)
{
s3c64xx_init_io(NULL, 0);
- s3c24xx_init_clocks(12000000);
+ s3c64xx_set_xtal_freq(12000000);
s3c24xx_init_uarts(crag6410_uartcfgs, ARRAY_SIZE(crag6410_uartcfgs));
samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
diff --git a/arch/arm/mach-s3c64xx/mach-hmt.c b/arch/arm/mach-s3c64xx/mach-hmt.c
index f39569e..e806404 100644
--- a/arch/arm/mach-s3c64xx/mach-hmt.c
+++ b/arch/arm/mach-s3c64xx/mach-hmt.c
@@ -247,7 +247,7 @@
static void __init hmt_map_io(void)
{
s3c64xx_init_io(hmt_iodesc, ARRAY_SIZE(hmt_iodesc));
- s3c24xx_init_clocks(12000000);
+ s3c64xx_set_xtal_freq(12000000);
s3c24xx_init_uarts(hmt_uartcfgs, ARRAY_SIZE(hmt_uartcfgs));
samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
}
diff --git a/arch/arm/mach-s3c64xx/mach-mini6410.c b/arch/arm/mach-s3c64xx/mach-mini6410.c
index fc043e3..58d46a3 100644
--- a/arch/arm/mach-s3c64xx/mach-mini6410.c
+++ b/arch/arm/mach-s3c64xx/mach-mini6410.c
@@ -231,7 +231,7 @@
u32 tmp;
s3c64xx_init_io(NULL, 0);
- s3c24xx_init_clocks(12000000);
+ s3c64xx_set_xtal_freq(12000000);
s3c24xx_init_uarts(mini6410_uartcfgs, ARRAY_SIZE(mini6410_uartcfgs));
samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
diff --git a/arch/arm/mach-s3c64xx/mach-ncp.c b/arch/arm/mach-s3c64xx/mach-ncp.c
index 7e2c390..2067b0b 100644
--- a/arch/arm/mach-s3c64xx/mach-ncp.c
+++ b/arch/arm/mach-s3c64xx/mach-ncp.c
@@ -86,7 +86,7 @@
static void __init ncp_map_io(void)
{
s3c64xx_init_io(ncp_iodesc, ARRAY_SIZE(ncp_iodesc));
- s3c24xx_init_clocks(12000000);
+ s3c64xx_set_xtal_freq(12000000);
s3c24xx_init_uarts(ncp_uartcfgs, ARRAY_SIZE(ncp_uartcfgs));
samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
}
diff --git a/arch/arm/mach-s3c64xx/mach-s3c64xx-dt.c b/arch/arm/mach-s3c64xx/mach-s3c64xx-dt.c
new file mode 100644
index 0000000..7eb9a10
--- /dev/null
+++ b/arch/arm/mach-s3c64xx/mach-s3c64xx-dt.c
@@ -0,0 +1,85 @@
+/*
+ * Samsung's S3C64XX flattened device tree enabled machine
+ *
+ * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/clk-provider.h>
+#include <linux/irqchip.h>
+#include <linux/of_platform.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/system_misc.h>
+
+#include <plat/cpu.h>
+#include <plat/watchdog-reset.h>
+
+#include <mach/map.h>
+
+#include "common.h"
+
+/*
+ * IO mapping for shared system controller IP.
+ *
+ * FIXME: Make remaining drivers use dynamic mapping.
+ */
+static struct map_desc s3c64xx_dt_iodesc[] __initdata = {
+ {
+ .virtual = (unsigned long)S3C_VA_SYS,
+ .pfn = __phys_to_pfn(S3C64XX_PA_SYSCON),
+ .length = SZ_4K,
+ .type = MT_DEVICE,
+ },
+};
+
+static void __init s3c64xx_dt_map_io(void)
+{
+ debug_ll_io_init();
+ iotable_init(s3c64xx_dt_iodesc, ARRAY_SIZE(s3c64xx_dt_iodesc));
+
+ s3c64xx_init_cpu();
+
+ if (!soc_is_s3c64xx())
+ panic("SoC is not S3C64xx!");
+}
+
+static void __init s3c64xx_dt_init_irq(void)
+{
+ of_clk_init(NULL);
+ samsung_wdt_reset_of_init();
+ irqchip_init();
+};
+
+static void __init s3c64xx_dt_init_machine(void)
+{
+ of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+}
+
+static void s3c64xx_dt_restart(enum reboot_mode mode, const char *cmd)
+{
+ if (mode != REBOOT_SOFT)
+ samsung_wdt_reset();
+
+ /* if all else fails, or mode was for soft, jump to 0 */
+ soft_restart(0);
+}
+
+static char const *s3c64xx_dt_compat[] __initdata = {
+ "samsung,s3c6400",
+ "samsung,s3c6410",
+ NULL
+};
+
+DT_MACHINE_START(S3C6400_DT, "Samsung S3C64xx (Flattened Device Tree)")
+ /* Maintainer: Tomasz Figa <tomasz.figa@gmail.com> */
+ .dt_compat = s3c64xx_dt_compat,
+ .map_io = s3c64xx_dt_map_io,
+ .init_irq = s3c64xx_dt_init_irq,
+ .init_machine = s3c64xx_dt_init_machine,
+ .restart = s3c64xx_dt_restart,
+MACHINE_END
diff --git a/arch/arm/mach-s3c64xx/mach-smartq.c b/arch/arm/mach-s3c64xx/mach-smartq.c
index 86d980b..0f47237 100644
--- a/arch/arm/mach-s3c64xx/mach-smartq.c
+++ b/arch/arm/mach-s3c64xx/mach-smartq.c
@@ -337,13 +337,6 @@
return ret;
}
-static int __init smartq_usb_otg_init(void)
-{
- clk_xusbxti.rate = 12000000;
-
- return 0;
-}
-
static int __init smartq_wifi_init(void)
{
int ret;
@@ -377,7 +370,8 @@
void __init smartq_map_io(void)
{
s3c64xx_init_io(smartq_iodesc, ARRAY_SIZE(smartq_iodesc));
- s3c24xx_init_clocks(12000000);
+ s3c64xx_set_xtal_freq(12000000);
+ s3c64xx_set_xusbxti_freq(12000000);
s3c24xx_init_uarts(smartq_uartcfgs, ARRAY_SIZE(smartq_uartcfgs));
samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
@@ -399,7 +393,6 @@
WARN_ON(smartq_lcd_setup_gpio());
WARN_ON(smartq_power_off_init());
WARN_ON(smartq_usb_host_init());
- WARN_ON(smartq_usb_otg_init());
WARN_ON(smartq_wifi_init());
platform_add_devices(smartq_devices, ARRAY_SIZE(smartq_devices));
diff --git a/arch/arm/mach-s3c64xx/mach-smdk6400.c b/arch/arm/mach-s3c64xx/mach-smdk6400.c
index d70c084..27381cf 100644
--- a/arch/arm/mach-s3c64xx/mach-smdk6400.c
+++ b/arch/arm/mach-s3c64xx/mach-smdk6400.c
@@ -65,7 +65,7 @@
static void __init smdk6400_map_io(void)
{
s3c64xx_init_io(smdk6400_iodesc, ARRAY_SIZE(smdk6400_iodesc));
- s3c24xx_init_clocks(12000000);
+ s3c64xx_set_xtal_freq(12000000);
s3c24xx_init_uarts(smdk6400_uartcfgs, ARRAY_SIZE(smdk6400_uartcfgs));
samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
}
diff --git a/arch/arm/mach-s3c64xx/mach-smdk6410.c b/arch/arm/mach-s3c64xx/mach-smdk6410.c
index d90b450..2a7b32c 100644
--- a/arch/arm/mach-s3c64xx/mach-smdk6410.c
+++ b/arch/arm/mach-s3c64xx/mach-smdk6410.c
@@ -634,7 +634,7 @@
u32 tmp;
s3c64xx_init_io(smdk6410_iodesc, ARRAY_SIZE(smdk6410_iodesc));
- s3c24xx_init_clocks(12000000);
+ s3c64xx_set_xtal_freq(12000000);
s3c24xx_init_uarts(smdk6410_uartcfgs, ARRAY_SIZE(smdk6410_uartcfgs));
samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
diff --git a/arch/arm/mach-s3c64xx/pm.c b/arch/arm/mach-s3c64xx/pm.c
index 6a1f91f..8cdb824 100644
--- a/arch/arm/mach-s3c64xx/pm.c
+++ b/arch/arm/mach-s3c64xx/pm.c
@@ -194,29 +194,8 @@
#endif
static struct sleep_save core_save[] = {
- SAVE_ITEM(S3C_APLL_LOCK),
- SAVE_ITEM(S3C_MPLL_LOCK),
- SAVE_ITEM(S3C_EPLL_LOCK),
- SAVE_ITEM(S3C_CLK_SRC),
- SAVE_ITEM(S3C_CLK_DIV0),
- SAVE_ITEM(S3C_CLK_DIV1),
- SAVE_ITEM(S3C_CLK_DIV2),
- SAVE_ITEM(S3C_CLK_OUT),
- SAVE_ITEM(S3C_HCLK_GATE),
- SAVE_ITEM(S3C_PCLK_GATE),
- SAVE_ITEM(S3C_SCLK_GATE),
- SAVE_ITEM(S3C_MEM0_GATE),
-
- SAVE_ITEM(S3C_EPLL_CON1),
- SAVE_ITEM(S3C_EPLL_CON0),
-
SAVE_ITEM(S3C64XX_MEM0DRVCON),
SAVE_ITEM(S3C64XX_MEM1DRVCON),
-
-#ifndef CONFIG_CPU_FREQ
- SAVE_ITEM(S3C_APLL_CON),
- SAVE_ITEM(S3C_MPLL_CON),
-#endif
};
static struct sleep_save misc_save[] = {
diff --git a/arch/arm/mach-s3c64xx/s3c6400.c b/arch/arm/mach-s3c64xx/s3c6400.c
index 4869714..3db0c98 100644
--- a/arch/arm/mach-s3c64xx/s3c6400.c
+++ b/arch/arm/mach-s3c64xx/s3c6400.c
@@ -9,6 +9,10 @@
* published by the Free Software Foundation.
*/
+/*
+ * NOTE: Code in this file is not used when booting with Device Tree support.
+ */
+
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/interrupt.h>
@@ -20,6 +24,7 @@
#include <linux/device.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
+#include <linux/of.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -58,12 +63,6 @@
s3c64xx_onenand1_setname("s3c6400-onenand");
}
-void __init s3c6400_init_clocks(int xtal)
-{
- s3c64xx_register_clocks(xtal, S3C6400_CLKDIV0_ARM_MASK);
- s3c64xx_setup_clocks();
-}
-
void __init s3c6400_init_irq(void)
{
/* VIC0 does not have IRQS 5..7,
@@ -82,6 +81,10 @@
static int __init s3c6400_core_init(void)
{
+ /* Not applicable when using DT. */
+ if (of_have_populated_dt())
+ return 0;
+
return subsys_system_register(&s3c6400_subsys, NULL);
}
diff --git a/arch/arm/mach-s3c64xx/s3c6410.c b/arch/arm/mach-s3c64xx/s3c6410.c
index 31c29fd..72b2278 100644
--- a/arch/arm/mach-s3c64xx/s3c6410.c
+++ b/arch/arm/mach-s3c64xx/s3c6410.c
@@ -10,6 +10,10 @@
* published by the Free Software Foundation.
*/
+/*
+ * NOTE: Code in this file is not used when booting with Device Tree support.
+ */
+
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/interrupt.h>
@@ -21,6 +25,7 @@
#include <linux/device.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
+#include <linux/of.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -62,13 +67,6 @@
s3c_cfcon_setname("s3c64xx-pata");
}
-void __init s3c6410_init_clocks(int xtal)
-{
- printk(KERN_DEBUG "%s: initialising clocks\n", __func__);
- s3c64xx_register_clocks(xtal, S3C6410_CLKDIV0_ARM_MASK);
- s3c64xx_setup_clocks();
-}
-
void __init s3c6410_init_irq(void)
{
/* VIC0 is missing IRQ7, VIC1 is fully populated. */
@@ -86,6 +84,10 @@
static int __init s3c6410_core_init(void)
{
+ /* Not applicable when using DT. */
+ if (of_have_populated_dt())
+ return 0;
+
return subsys_system_register(&s3c6410_subsys, NULL);
}
diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index 1f94c31..b452405 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -101,6 +101,12 @@
select SH_CLK_CPG
select RENESAS_IRQC
+config ARCH_R8A7791
+ bool "R-Car M2 (R8A77910)"
+ select ARM_GIC
+ select CPU_V7
+ select SH_CLK_CPG
+
config ARCH_EMEV2
bool "Emma Mobile EV2"
select ARCH_WANT_OPTIONAL_GPIOLIB
diff --git a/arch/arm/mach-shmobile/Makefile b/arch/arm/mach-shmobile/Makefile
index 2705bfa..228193c 100644
--- a/arch/arm/mach-shmobile/Makefile
+++ b/arch/arm/mach-shmobile/Makefile
@@ -15,6 +15,7 @@
obj-$(CONFIG_ARCH_R8A7778) += setup-r8a7778.o
obj-$(CONFIG_ARCH_R8A7779) += setup-r8a7779.o
obj-$(CONFIG_ARCH_R8A7790) += setup-r8a7790.o
+obj-$(CONFIG_ARCH_R8A7791) += setup-r8a7791.o
obj-$(CONFIG_ARCH_EMEV2) += setup-emev2.o
# Clock objects
@@ -27,6 +28,7 @@
obj-$(CONFIG_ARCH_R8A7778) += clock-r8a7778.o
obj-$(CONFIG_ARCH_R8A7779) += clock-r8a7779.o
obj-$(CONFIG_ARCH_R8A7790) += clock-r8a7790.o
+obj-$(CONFIG_ARCH_R8A7791) += clock-r8a7791.o
obj-$(CONFIG_ARCH_EMEV2) += clock-emev2.o
endif
diff --git a/arch/arm/mach-shmobile/clock-r8a7778.c b/arch/arm/mach-shmobile/clock-r8a7778.c
index c4bf2d8..fb6af83 100644
--- a/arch/arm/mach-shmobile/clock-r8a7778.c
+++ b/arch/arm/mach-shmobile/clock-r8a7778.c
@@ -69,6 +69,15 @@
.mapping = &cpg_mapping,
};
+static struct clk audio_clk_a = {
+};
+
+static struct clk audio_clk_b = {
+};
+
+static struct clk audio_clk_c = {
+};
+
/*
* clock ratio of these clock will be updated
* on r8a7778_clock_init()
@@ -100,18 +109,23 @@
&p_clk,
&g_clk,
&z_clk,
+ &audio_clk_a,
+ &audio_clk_b,
+ &audio_clk_c,
};
enum {
MSTP331,
MSTP323, MSTP322, MSTP321,
+ MSTP311, MSTP310,
+ MSTP309, MSTP308, MSTP307,
MSTP114,
MSTP110, MSTP109,
MSTP100,
MSTP030,
MSTP029, MSTP028, MSTP027, MSTP026, MSTP025, MSTP024, MSTP023, MSTP022, MSTP021,
- MSTP016, MSTP015,
- MSTP007,
+ MSTP016, MSTP015, MSTP012, MSTP011, MSTP010,
+ MSTP009, MSTP008, MSTP007,
MSTP_NR };
static struct clk mstp_clks[MSTP_NR] = {
@@ -119,6 +133,11 @@
[MSTP323] = SH_CLK_MSTP32(&p_clk, MSTPCR3, 23, 0), /* SDHI0 */
[MSTP322] = SH_CLK_MSTP32(&p_clk, MSTPCR3, 22, 0), /* SDHI1 */
[MSTP321] = SH_CLK_MSTP32(&p_clk, MSTPCR3, 21, 0), /* SDHI2 */
+ [MSTP311] = SH_CLK_MSTP32(&p_clk, MSTPCR3, 11, 0), /* SSI4 */
+ [MSTP310] = SH_CLK_MSTP32(&p_clk, MSTPCR3, 10, 0), /* SSI5 */
+ [MSTP309] = SH_CLK_MSTP32(&p_clk, MSTPCR3, 9, 0), /* SSI6 */
+ [MSTP308] = SH_CLK_MSTP32(&p_clk, MSTPCR3, 8, 0), /* SSI7 */
+ [MSTP307] = SH_CLK_MSTP32(&p_clk, MSTPCR3, 7, 0), /* SSI8 */
[MSTP114] = SH_CLK_MSTP32(&p_clk, MSTPCR1, 14, 0), /* Ether */
[MSTP110] = SH_CLK_MSTP32(&s_clk, MSTPCR1, 10, 0), /* VIN0 */
[MSTP109] = SH_CLK_MSTP32(&s_clk, MSTPCR1, 9, 0), /* VIN1 */
@@ -135,11 +154,20 @@
[MSTP021] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 21, 0), /* SCIF5 */
[MSTP016] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 16, 0), /* TMU0 */
[MSTP015] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 15, 0), /* TMU1 */
+ [MSTP012] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 12, 0), /* SSI0 */
+ [MSTP011] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 11, 0), /* SSI1 */
+ [MSTP010] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 10, 0), /* SSI2 */
+ [MSTP009] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 9, 0), /* SSI3 */
+ [MSTP008] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 8, 0), /* SRU */
[MSTP007] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 7, 0), /* HSPI */
};
static struct clk_lookup lookups[] = {
/* main */
+ CLKDEV_CON_ID("audio_clk_a", &audio_clk_a),
+ CLKDEV_CON_ID("audio_clk_b", &audio_clk_b),
+ CLKDEV_CON_ID("audio_clk_c", &audio_clk_c),
+ CLKDEV_CON_ID("audio_clk_internal", &s1_clk),
CLKDEV_CON_ID("shyway_clk", &s_clk),
CLKDEV_CON_ID("peripheral_clk", &p_clk),
@@ -153,6 +181,7 @@
CLKDEV_DEV_ID("r8a7778-vin.1", &mstp_clks[MSTP109]), /* VIN1 */
CLKDEV_DEV_ID("ehci-platform", &mstp_clks[MSTP100]), /* USB EHCI port0/1 */
CLKDEV_DEV_ID("ohci-platform", &mstp_clks[MSTP100]), /* USB OHCI port0/1 */
+ CLKDEV_DEV_ID("renesas_usbhs", &mstp_clks[MSTP100]), /* USB FUNC */
CLKDEV_DEV_ID("i2c-rcar.0", &mstp_clks[MSTP030]), /* I2C0 */
CLKDEV_DEV_ID("i2c-rcar.1", &mstp_clks[MSTP029]), /* I2C1 */
CLKDEV_DEV_ID("i2c-rcar.2", &mstp_clks[MSTP028]), /* I2C2 */
@@ -168,6 +197,17 @@
CLKDEV_DEV_ID("sh-hspi.0", &mstp_clks[MSTP007]), /* HSPI0 */
CLKDEV_DEV_ID("sh-hspi.1", &mstp_clks[MSTP007]), /* HSPI1 */
CLKDEV_DEV_ID("sh-hspi.2", &mstp_clks[MSTP007]), /* HSPI2 */
+ CLKDEV_DEV_ID("rcar_sound", &mstp_clks[MSTP008]), /* SRU */
+
+ CLKDEV_ICK_ID("ssi.0", "rcar_sound", &mstp_clks[MSTP012]),
+ CLKDEV_ICK_ID("ssi.1", "rcar_sound", &mstp_clks[MSTP011]),
+ CLKDEV_ICK_ID("ssi.2", "rcar_sound", &mstp_clks[MSTP010]),
+ CLKDEV_ICK_ID("ssi.3", "rcar_sound", &mstp_clks[MSTP009]),
+ CLKDEV_ICK_ID("ssi.4", "rcar_sound", &mstp_clks[MSTP311]),
+ CLKDEV_ICK_ID("ssi.5", "rcar_sound", &mstp_clks[MSTP310]),
+ CLKDEV_ICK_ID("ssi.6", "rcar_sound", &mstp_clks[MSTP309]),
+ CLKDEV_ICK_ID("ssi.7", "rcar_sound", &mstp_clks[MSTP308]),
+ CLKDEV_ICK_ID("ssi.8", "rcar_sound", &mstp_clks[MSTP307]),
};
void __init r8a7778_clock_init(void)
diff --git a/arch/arm/mach-shmobile/clock-r8a7779.c b/arch/arm/mach-shmobile/clock-r8a7779.c
index bd6ad92..1f7080f 100644
--- a/arch/arm/mach-shmobile/clock-r8a7779.c
+++ b/arch/arm/mach-shmobile/clock-r8a7779.c
@@ -200,7 +200,7 @@
CLKDEV_DEV_ID("sh_mobile_sdhi.1", &mstp_clks[MSTP322]), /* SDHI1 */
CLKDEV_DEV_ID("sh_mobile_sdhi.2", &mstp_clks[MSTP321]), /* SDHI2 */
CLKDEV_DEV_ID("sh_mobile_sdhi.3", &mstp_clks[MSTP320]), /* SDHI3 */
- CLKDEV_DEV_ID("rcar-du.0", &mstp_clks[MSTP103]), /* DU */
+ CLKDEV_DEV_ID("rcar-du-r8a7779", &mstp_clks[MSTP103]), /* DU */
};
void __init r8a7779_clock_init(void)
diff --git a/arch/arm/mach-shmobile/clock-r8a7790.c b/arch/arm/mach-shmobile/clock-r8a7790.c
index fc36d3d..d99b87b 100644
--- a/arch/arm/mach-shmobile/clock-r8a7790.c
+++ b/arch/arm/mach-shmobile/clock-r8a7790.c
@@ -182,7 +182,7 @@
/* MSTP */
enum {
MSTP813,
- MSTP721, MSTP720,
+ MSTP726, MSTP725, MSTP724, MSTP723, MSTP722, MSTP721, MSTP720,
MSTP717, MSTP716,
MSTP522,
MSTP315, MSTP314, MSTP313, MSTP312, MSTP311, MSTP305, MSTP304,
@@ -193,6 +193,11 @@
static struct clk mstp_clks[MSTP_NR] = {
[MSTP813] = SH_CLK_MSTP32(&p_clk, SMSTPCR8, 13, 0), /* Ether */
+ [MSTP726] = SH_CLK_MSTP32(&zx_clk, SMSTPCR7, 26, 0), /* LVDS0 */
+ [MSTP725] = SH_CLK_MSTP32(&zx_clk, SMSTPCR7, 25, 0), /* LVDS1 */
+ [MSTP724] = SH_CLK_MSTP32(&zx_clk, SMSTPCR7, 24, 0), /* DU0 */
+ [MSTP723] = SH_CLK_MSTP32(&zx_clk, SMSTPCR7, 23, 0), /* DU1 */
+ [MSTP722] = SH_CLK_MSTP32(&zx_clk, SMSTPCR7, 22, 0), /* DU2 */
[MSTP721] = SH_CLK_MSTP32(&p_clk, SMSTPCR7, 21, 0), /* SCIF0 */
[MSTP720] = SH_CLK_MSTP32(&p_clk, SMSTPCR7, 20, 0), /* SCIF1 */
[MSTP717] = SH_CLK_MSTP32(&zs_clk, SMSTPCR7, 17, 0), /* HSCIF0 */
@@ -251,6 +256,11 @@
CLKDEV_CON_ID("ssprs", &div6_clks[DIV6_SSPRS]),
/* MSTP */
+ CLKDEV_ICK_ID("lvds.0", "rcar-du-r8a7790", &mstp_clks[MSTP726]),
+ CLKDEV_ICK_ID("lvds.1", "rcar-du-r8a7790", &mstp_clks[MSTP725]),
+ CLKDEV_ICK_ID("du.0", "rcar-du-r8a7790", &mstp_clks[MSTP724]),
+ CLKDEV_ICK_ID("du.1", "rcar-du-r8a7790", &mstp_clks[MSTP723]),
+ CLKDEV_ICK_ID("du.2", "rcar-du-r8a7790", &mstp_clks[MSTP722]),
CLKDEV_DEV_ID("sh-sci.0", &mstp_clks[MSTP204]),
CLKDEV_DEV_ID("sh-sci.1", &mstp_clks[MSTP203]),
CLKDEV_DEV_ID("sh-sci.2", &mstp_clks[MSTP206]),
diff --git a/arch/arm/mach-shmobile/clock-r8a7791.c b/arch/arm/mach-shmobile/clock-r8a7791.c
new file mode 100644
index 0000000..c9a26f1
--- /dev/null
+++ b/arch/arm/mach-shmobile/clock-r8a7791.c
@@ -0,0 +1,237 @@
+/*
+ * r8a7791 clock framework support
+ *
+ * Copyright (C) 2013 Renesas Electronics Corporation
+ * Copyright (C) 2013 Renesas Solutions Corp.
+ * Copyright (C) 2013 Magnus Damm
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/sh_clk.h>
+#include <linux/clkdev.h>
+#include <mach/clock.h>
+#include <mach/common.h>
+
+/*
+ * MD EXTAL PLL0 PLL1 PLL3
+ * 14 13 19 (MHz) *1 *1
+ *---------------------------------------------------
+ * 0 0 0 15 x 1 x172/2 x208/2 x106
+ * 0 0 1 15 x 1 x172/2 x208/2 x88
+ * 0 1 0 20 x 1 x130/2 x156/2 x80
+ * 0 1 1 20 x 1 x130/2 x156/2 x66
+ * 1 0 0 26 / 2 x200/2 x240/2 x122
+ * 1 0 1 26 / 2 x200/2 x240/2 x102
+ * 1 1 0 30 / 2 x172/2 x208/2 x106
+ * 1 1 1 30 / 2 x172/2 x208/2 x88
+ *
+ * *1 : Table 7.6 indicates VCO ouput (PLLx = VCO/2)
+ * see "p1 / 2" on R8A7791_CLOCK_ROOT() below
+ */
+
+#define MD(nr) (1 << nr)
+
+#define CPG_BASE 0xe6150000
+#define CPG_LEN 0x1000
+
+#define SMSTPCR0 0xE6150130
+#define SMSTPCR1 0xE6150134
+#define SMSTPCR2 0xe6150138
+#define SMSTPCR3 0xE615013C
+#define SMSTPCR5 0xE6150144
+#define SMSTPCR7 0xe615014c
+#define SMSTPCR8 0xE6150990
+#define SMSTPCR9 0xE6150994
+#define SMSTPCR10 0xE6150998
+#define SMSTPCR11 0xE615099C
+
+#define MODEMR 0xE6160060
+#define SDCKCR 0xE6150074
+#define SD2CKCR 0xE6150078
+#define SD3CKCR 0xE615007C
+#define MMC0CKCR 0xE6150240
+#define MMC1CKCR 0xE6150244
+#define SSPCKCR 0xE6150248
+#define SSPRSCKCR 0xE615024C
+
+static struct clk_mapping cpg_mapping = {
+ .phys = CPG_BASE,
+ .len = CPG_LEN,
+};
+
+static struct clk extal_clk = {
+ /* .rate will be updated on r8a7791_clock_init() */
+ .mapping = &cpg_mapping,
+};
+
+static struct sh_clk_ops followparent_clk_ops = {
+ .recalc = followparent_recalc,
+};
+
+static struct clk main_clk = {
+ /* .parent will be set r8a73a4_clock_init */
+ .ops = &followparent_clk_ops,
+};
+
+/*
+ * clock ratio of these clock will be updated
+ * on r8a7791_clock_init()
+ */
+SH_FIXED_RATIO_CLK_SET(pll1_clk, main_clk, 1, 1);
+SH_FIXED_RATIO_CLK_SET(pll3_clk, main_clk, 1, 1);
+
+/* fixed ratio clock */
+SH_FIXED_RATIO_CLK_SET(extal_div2_clk, extal_clk, 1, 2);
+SH_FIXED_RATIO_CLK_SET(cp_clk, extal_clk, 1, 2);
+
+SH_FIXED_RATIO_CLK_SET(pll1_div2_clk, pll1_clk, 1, 2);
+SH_FIXED_RATIO_CLK_SET(hp_clk, pll1_clk, 1, 12);
+SH_FIXED_RATIO_CLK_SET(p_clk, pll1_clk, 1, 24);
+SH_FIXED_RATIO_CLK_SET(rclk_clk, pll1_clk, 1, (48 * 1024));
+SH_FIXED_RATIO_CLK_SET(mp_clk, pll1_div2_clk, 1, 15);
+
+static struct clk *main_clks[] = {
+ &extal_clk,
+ &extal_div2_clk,
+ &main_clk,
+ &pll1_clk,
+ &pll1_div2_clk,
+ &pll3_clk,
+ &hp_clk,
+ &p_clk,
+ &rclk_clk,
+ &mp_clk,
+ &cp_clk,
+};
+
+/* MSTP */
+enum {
+ MSTP721, MSTP720,
+ MSTP719, MSTP718, MSTP715, MSTP714,
+ MSTP216, MSTP207, MSTP206,
+ MSTP204, MSTP203, MSTP202, MSTP1105, MSTP1106, MSTP1107,
+ MSTP124,
+ MSTP_NR
+};
+
+static struct clk mstp_clks[MSTP_NR] = {
+ [MSTP721] = SH_CLK_MSTP32(&p_clk, SMSTPCR7, 21, 0), /* SCIF0 */
+ [MSTP720] = SH_CLK_MSTP32(&p_clk, SMSTPCR7, 20, 0), /* SCIF1 */
+ [MSTP719] = SH_CLK_MSTP32(&p_clk, SMSTPCR7, 19, 0), /* SCIF2 */
+ [MSTP718] = SH_CLK_MSTP32(&p_clk, SMSTPCR7, 18, 0), /* SCIF3 */
+ [MSTP715] = SH_CLK_MSTP32(&p_clk, SMSTPCR7, 15, 0), /* SCIF4 */
+ [MSTP714] = SH_CLK_MSTP32(&p_clk, SMSTPCR7, 14, 0), /* SCIF5 */
+ [MSTP216] = SH_CLK_MSTP32(&mp_clk, SMSTPCR2, 16, 0), /* SCIFB2 */
+ [MSTP207] = SH_CLK_MSTP32(&mp_clk, SMSTPCR2, 7, 0), /* SCIFB1 */
+ [MSTP206] = SH_CLK_MSTP32(&mp_clk, SMSTPCR2, 6, 0), /* SCIFB0 */
+ [MSTP204] = SH_CLK_MSTP32(&mp_clk, SMSTPCR2, 4, 0), /* SCIFA0 */
+ [MSTP203] = SH_CLK_MSTP32(&mp_clk, SMSTPCR2, 3, 0), /* SCIFA1 */
+ [MSTP202] = SH_CLK_MSTP32(&mp_clk, SMSTPCR2, 2, 0), /* SCIFA2 */
+ [MSTP1105] = SH_CLK_MSTP32(&mp_clk, SMSTPCR11, 5, 0), /* SCIFA3 */
+ [MSTP1106] = SH_CLK_MSTP32(&mp_clk, SMSTPCR11, 6, 0), /* SCIFA4 */
+ [MSTP1107] = SH_CLK_MSTP32(&mp_clk, SMSTPCR11, 7, 0), /* SCIFA5 */
+ [MSTP124] = SH_CLK_MSTP32(&rclk_clk, SMSTPCR1, 24, 0), /* CMT0 */
+};
+
+static struct clk_lookup lookups[] = {
+
+ /* main clocks */
+ CLKDEV_CON_ID("extal", &extal_clk),
+ CLKDEV_CON_ID("extal_div2", &extal_div2_clk),
+ CLKDEV_CON_ID("main", &main_clk),
+ CLKDEV_CON_ID("pll1", &pll1_clk),
+ CLKDEV_CON_ID("pll1_div2", &pll1_div2_clk),
+ CLKDEV_CON_ID("pll3", &pll3_clk),
+ CLKDEV_CON_ID("hp", &hp_clk),
+ CLKDEV_CON_ID("p", &p_clk),
+ CLKDEV_CON_ID("rclk", &rclk_clk),
+ CLKDEV_CON_ID("mp", &mp_clk),
+ CLKDEV_CON_ID("cp", &cp_clk),
+ CLKDEV_CON_ID("peripheral_clk", &hp_clk),
+
+ /* MSTP */
+ CLKDEV_DEV_ID("sh-sci.0", &mstp_clks[MSTP204]), /* SCIFA0 */
+ CLKDEV_DEV_ID("sh-sci.1", &mstp_clks[MSTP203]), /* SCIFA1 */
+ CLKDEV_DEV_ID("sh-sci.2", &mstp_clks[MSTP206]), /* SCIFB0 */
+ CLKDEV_DEV_ID("sh-sci.3", &mstp_clks[MSTP207]), /* SCIFB1 */
+ CLKDEV_DEV_ID("sh-sci.4", &mstp_clks[MSTP216]), /* SCIFB2 */
+ CLKDEV_DEV_ID("sh-sci.5", &mstp_clks[MSTP202]), /* SCIFA2 */
+ CLKDEV_DEV_ID("sh-sci.6", &mstp_clks[MSTP721]), /* SCIF0 */
+ CLKDEV_DEV_ID("sh-sci.7", &mstp_clks[MSTP720]), /* SCIF1 */
+ CLKDEV_DEV_ID("sh-sci.8", &mstp_clks[MSTP719]), /* SCIF2 */
+ CLKDEV_DEV_ID("sh-sci.9", &mstp_clks[MSTP718]), /* SCIF3 */
+ CLKDEV_DEV_ID("sh-sci.10", &mstp_clks[MSTP715]), /* SCIF4 */
+ CLKDEV_DEV_ID("sh-sci.11", &mstp_clks[MSTP714]), /* SCIF5 */
+ CLKDEV_DEV_ID("sh-sci.12", &mstp_clks[MSTP1105]), /* SCIFA3 */
+ CLKDEV_DEV_ID("sh-sci.13", &mstp_clks[MSTP1106]), /* SCIFA4 */
+ CLKDEV_DEV_ID("sh-sci.14", &mstp_clks[MSTP1107]), /* SCIFA5 */
+ CLKDEV_DEV_ID("sh_cmt.0", &mstp_clks[MSTP124]),
+};
+
+#define R8A7791_CLOCK_ROOT(e, m, p0, p1, p30, p31) \
+ extal_clk.rate = e * 1000 * 1000; \
+ main_clk.parent = m; \
+ SH_CLK_SET_RATIO(&pll1_clk_ratio, p1 / 2, 1); \
+ if (mode & MD(19)) \
+ SH_CLK_SET_RATIO(&pll3_clk_ratio, p31, 1); \
+ else \
+ SH_CLK_SET_RATIO(&pll3_clk_ratio, p30, 1)
+
+
+void __init r8a7791_clock_init(void)
+{
+ void __iomem *modemr = ioremap_nocache(MODEMR, PAGE_SIZE);
+ u32 mode;
+ int k, ret = 0;
+
+ BUG_ON(!modemr);
+ mode = ioread32(modemr);
+ iounmap(modemr);
+
+ switch (mode & (MD(14) | MD(13))) {
+ case 0:
+ R8A7791_CLOCK_ROOT(15, &extal_clk, 172, 208, 106, 88);
+ break;
+ case MD(13):
+ R8A7791_CLOCK_ROOT(20, &extal_clk, 130, 156, 80, 66);
+ break;
+ case MD(14):
+ R8A7791_CLOCK_ROOT(26, &extal_div2_clk, 200, 240, 122, 102);
+ break;
+ case MD(13) | MD(14):
+ R8A7791_CLOCK_ROOT(30, &extal_div2_clk, 172, 208, 106, 88);
+ break;
+ }
+
+ for (k = 0; !ret && (k < ARRAY_SIZE(main_clks)); k++)
+ ret = clk_register(main_clks[k]);
+
+ if (!ret)
+ ret = sh_clk_mstp_register(mstp_clks, MSTP_NR);
+
+ clkdev_add_table(lookups, ARRAY_SIZE(lookups));
+
+ if (!ret)
+ shmobile_clk_init();
+ else
+ goto epanic;
+
+ return;
+
+epanic:
+ panic("failed to setup r8a7791 clocks\n");
+}
diff --git a/arch/arm/mach-shmobile/include/mach/r8a7778.h b/arch/arm/mach-shmobile/include/mach/r8a7778.h
index adfcf51..ea1dca6 100644
--- a/arch/arm/mach-shmobile/include/mach/r8a7778.h
+++ b/arch/arm/mach-shmobile/include/mach/r8a7778.h
@@ -35,4 +35,6 @@
extern void r8a7778_init_irq_extpin(int irlm);
extern void r8a7778_pinmux_init(void);
+extern int r8a7778_usb_phy_power(bool enable);
+
#endif /* __ASM_R8A7778_H__ */
diff --git a/arch/arm/mach-shmobile/include/mach/r8a7791.h b/arch/arm/mach-shmobile/include/mach/r8a7791.h
new file mode 100644
index 0000000..2e6d661
--- /dev/null
+++ b/arch/arm/mach-shmobile/include/mach/r8a7791.h
@@ -0,0 +1,8 @@
+#ifndef __ASM_R8A7791_H__
+#define __ASM_R8A7791_H__
+
+void r8a7791_add_dt_devices(void);
+void r8a7791_clock_init(void);
+void r8a7791_init_early(void);
+
+#endif /* __ASM_R8A7791_H__ */
diff --git a/arch/arm/mach-shmobile/setup-r8a7778.c b/arch/arm/mach-shmobile/setup-r8a7778.c
index 6a2657e..e484d14 100644
--- a/arch/arm/mach-shmobile/setup-r8a7778.c
+++ b/arch/arm/mach-shmobile/setup-r8a7778.c
@@ -95,29 +95,46 @@
&sh_tmu##idx##_platform_data, \
sizeof(sh_tmu##idx##_platform_data))
-/* USB */
-static struct usb_phy *phy;
+int r8a7778_usb_phy_power(bool enable)
+{
+ static struct usb_phy *phy = NULL;
+ int ret = 0;
+ if (!phy)
+ phy = usb_get_phy(USB_PHY_TYPE_USB2);
+
+ if (IS_ERR(phy)) {
+ pr_err("kernel doesn't have usb phy driver\n");
+ return PTR_ERR(phy);
+ }
+
+ if (enable)
+ ret = usb_phy_init(phy);
+ else
+ usb_phy_shutdown(phy);
+
+ return ret;
+}
+
+/* USB */
static int usb_power_on(struct platform_device *pdev)
{
- if (IS_ERR(phy))
- return PTR_ERR(phy);
+ int ret = r8a7778_usb_phy_power(true);
+
+ if (ret)
+ return ret;
pm_runtime_enable(&pdev->dev);
pm_runtime_get_sync(&pdev->dev);
- usb_phy_init(phy);
-
return 0;
}
static void usb_power_off(struct platform_device *pdev)
{
- if (IS_ERR(phy))
+ if (r8a7778_usb_phy_power(false))
return;
- usb_phy_shutdown(phy);
-
pm_runtime_put_sync(&pdev->dev);
pm_runtime_disable(&pdev->dev);
}
@@ -353,8 +370,6 @@
void __init r8a7778_init_late(void)
{
- phy = usb_get_phy(USB_PHY_TYPE_USB2);
-
platform_device_register_full(&ehci_info);
platform_device_register_full(&ohci_info);
}
diff --git a/arch/arm/mach-shmobile/setup-r8a7791.c b/arch/arm/mach-shmobile/setup-r8a7791.c
new file mode 100644
index 0000000..b56399d
--- /dev/null
+++ b/arch/arm/mach-shmobile/setup-r8a7791.c
@@ -0,0 +1,149 @@
+/*
+ * r8a7791 processor support
+ *
+ * Copyright (C) 2013 Renesas Electronics Corporation
+ * Copyright (C) 2013 Renesas Solutions Corp.
+ * Copyright (C) 2013 Magnus Damm
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/of_platform.h>
+#include <linux/serial_sci.h>
+#include <linux/sh_timer.h>
+#include <mach/common.h>
+#include <mach/irqs.h>
+#include <mach/r8a7791.h>
+#include <asm/mach/arch.h>
+
+#define SCIF_COMMON(scif_type, baseaddr, irq) \
+ .type = scif_type, \
+ .mapbase = baseaddr, \
+ .flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP, \
+ .irqs = SCIx_IRQ_MUXED(irq)
+
+#define SCIFA_DATA(index, baseaddr, irq) \
+[index] = { \
+ SCIF_COMMON(PORT_SCIFA, baseaddr, irq), \
+ .scbrr_algo_id = SCBRR_ALGO_4, \
+ .scscr = SCSCR_RE | SCSCR_TE, \
+}
+
+#define SCIFB_DATA(index, baseaddr, irq) \
+[index] = { \
+ SCIF_COMMON(PORT_SCIFB, baseaddr, irq), \
+ .scbrr_algo_id = SCBRR_ALGO_4, \
+ .scscr = SCSCR_RE | SCSCR_TE, \
+}
+
+#define SCIF_DATA(index, baseaddr, irq) \
+[index] = { \
+ SCIF_COMMON(PORT_SCIF, baseaddr, irq), \
+ .scbrr_algo_id = SCBRR_ALGO_2, \
+ .scscr = SCSCR_RE | SCSCR_TE, \
+}
+
+#define HSCIF_DATA(index, baseaddr, irq) \
+[index] = { \
+ SCIF_COMMON(PORT_HSCIF, baseaddr, irq), \
+ .scbrr_algo_id = SCBRR_ALGO_6, \
+ .scscr = SCSCR_RE | SCSCR_TE, \
+}
+
+enum { SCIFA0, SCIFA1, SCIFB0, SCIFB1, SCIFB2, SCIFA2, SCIF0, SCIF1,
+ SCIF2, SCIF3, SCIF4, SCIF5, SCIFA3, SCIFA4, SCIFA5 };
+
+static const struct plat_sci_port scif[] __initconst = {
+ SCIFA_DATA(SCIFA0, 0xe6c40000, gic_spi(144)), /* SCIFA0 */
+ SCIFA_DATA(SCIFA1, 0xe6c50000, gic_spi(145)), /* SCIFA1 */
+ SCIFB_DATA(SCIFB0, 0xe6c20000, gic_spi(148)), /* SCIFB0 */
+ SCIFB_DATA(SCIFB1, 0xe6c30000, gic_spi(149)), /* SCIFB1 */
+ SCIFB_DATA(SCIFB2, 0xe6ce0000, gic_spi(150)), /* SCIFB2 */
+ SCIFA_DATA(SCIFA2, 0xe6c60000, gic_spi(151)), /* SCIFA2 */
+ SCIF_DATA(SCIF0, 0xe6e60000, gic_spi(152)), /* SCIF0 */
+ SCIF_DATA(SCIF1, 0xe6e68000, gic_spi(153)), /* SCIF1 */
+ SCIF_DATA(SCIF2, 0xe6e58000, gic_spi(22)), /* SCIF2 */
+ SCIF_DATA(SCIF3, 0xe6ea8000, gic_spi(23)), /* SCIF3 */
+ SCIF_DATA(SCIF4, 0xe6ee0000, gic_spi(24)), /* SCIF4 */
+ SCIF_DATA(SCIF5, 0xe6ee8000, gic_spi(25)), /* SCIF5 */
+ SCIFA_DATA(SCIFA3, 0xe6c70000, gic_spi(29)), /* SCIFA3 */
+ SCIFA_DATA(SCIFA4, 0xe6c78000, gic_spi(30)), /* SCIFA4 */
+ SCIFA_DATA(SCIFA5, 0xe6c80000, gic_spi(31)), /* SCIFA5 */
+};
+
+static inline void r8a7791_register_scif(int idx)
+{
+ platform_device_register_data(&platform_bus, "sh-sci", idx, &scif[idx],
+ sizeof(struct plat_sci_port));
+}
+
+static const struct sh_timer_config cmt00_platform_data __initconst = {
+ .name = "CMT00",
+ .timer_bit = 0,
+ .clockevent_rating = 80,
+};
+
+static const struct resource cmt00_resources[] __initconst = {
+ DEFINE_RES_MEM(0xffca0510, 0x0c),
+ DEFINE_RES_MEM(0xffca0500, 0x04),
+ DEFINE_RES_IRQ(gic_spi(142)), /* CMT0_0 */
+};
+
+#define r8a7791_register_cmt(idx) \
+ platform_device_register_resndata(&platform_bus, "sh_cmt", \
+ idx, cmt##idx##_resources, \
+ ARRAY_SIZE(cmt##idx##_resources), \
+ &cmt##idx##_platform_data, \
+ sizeof(struct sh_timer_config))
+
+void __init r8a7791_add_dt_devices(void)
+{
+ r8a7791_register_scif(SCIFA0);
+ r8a7791_register_scif(SCIFA1);
+ r8a7791_register_scif(SCIFB0);
+ r8a7791_register_scif(SCIFB1);
+ r8a7791_register_scif(SCIFB2);
+ r8a7791_register_scif(SCIFA2);
+ r8a7791_register_scif(SCIF0);
+ r8a7791_register_scif(SCIF1);
+ r8a7791_register_scif(SCIF2);
+ r8a7791_register_scif(SCIF3);
+ r8a7791_register_scif(SCIF4);
+ r8a7791_register_scif(SCIF5);
+ r8a7791_register_scif(SCIFA3);
+ r8a7791_register_scif(SCIFA4);
+ r8a7791_register_scif(SCIFA5);
+ r8a7791_register_cmt(00);
+}
+
+void __init r8a7791_init_early(void)
+{
+#ifndef CONFIG_ARM_ARCH_TIMER
+ shmobile_setup_delay(1300, 2, 4); /* Cortex-A15 @ 1300MHz */
+#endif
+}
+
+#ifdef CONFIG_USE_OF
+static const char *r8a7791_boards_compat_dt[] __initdata = {
+ "renesas,r8a7791",
+ NULL,
+};
+
+DT_MACHINE_START(R8A7791_DT, "Generic R8A7791 (Flattened Device Tree)")
+ .init_early = r8a7791_init_early,
+ .dt_compat = r8a7791_boards_compat_dt,
+MACHINE_END
+#endif /* CONFIG_USE_OF */
diff --git a/arch/arm/mach-ux500/Makefile b/arch/arm/mach-ux500/Makefile
index fe1f3e2..616b96e 100644
--- a/arch/arm/mach-ux500/Makefile
+++ b/arch/arm/mach-ux500/Makefile
@@ -2,14 +2,11 @@
# Makefile for the linux kernel, U8500 machine.
#
-obj-y := cpu.o devices.o devices-common.o \
- id.o usb.o timer.o pm.o
+obj-y := cpu.o devices.o id.o timer.o pm.o
obj-$(CONFIG_CACHE_L2X0) += cache-l2x0.o
obj-$(CONFIG_UX500_SOC_DB8500) += cpu-db8500.o devices-db8500.o
obj-$(CONFIG_MACH_MOP500) += board-mop500.o board-mop500-sdi.o \
board-mop500-regulators.o \
- board-mop500-uib.o board-mop500-stuib.o \
- board-mop500-u8500uib.o \
board-mop500-pins.o \
board-mop500-audio.o
obj-$(CONFIG_SMP) += platsmp.o headsmp.o
diff --git a/arch/arm/mach-ux500/board-mop500-audio.c b/arch/arm/mach-ux500/board-mop500-audio.c
index ec08072..154e15f 100644
--- a/arch/arm/mach-ux500/board-mop500-audio.c
+++ b/arch/arm/mach-ux500/board-mop500-audio.c
@@ -68,40 +68,6 @@
.phy_channel = 1,
};
-static struct platform_device *db8500_add_msp_i2s(struct device *parent,
- int id,
- resource_size_t base, int irq,
- struct msp_i2s_platform_data *pdata)
-{
- struct platform_device *pdev;
- struct resource res[] = {
- DEFINE_RES_MEM(base, SZ_4K),
- DEFINE_RES_IRQ(irq),
- };
-
- pr_info("Register platform-device 'ux500-msp-i2s', id %d, irq %d\n",
- id, irq);
- pdev = platform_device_register_resndata(parent, "ux500-msp-i2s", id,
- res, ARRAY_SIZE(res),
- pdata, sizeof(*pdata));
- if (!pdev) {
- pr_err("Failed to register platform-device 'ux500-msp-i2s.%d'!\n",
- id);
- return NULL;
- }
-
- return pdev;
-}
-
-/* Platform device for ASoC MOP500 machine */
-static struct platform_device snd_soc_mop500 = {
- .name = "snd-soc-mop500",
- .id = 0,
- .dev = {
- .platform_data = NULL,
- },
-};
-
struct msp_i2s_platform_data msp2_platform_data = {
.id = MSP_I2S_2,
.msp_i2s_dma_rx = &msp2_dma_rx,
@@ -113,19 +79,3 @@
.msp_i2s_dma_rx = &msp1_dma_rx,
.msp_i2s_dma_tx = NULL,
};
-
-void mop500_audio_init(struct device *parent)
-{
- pr_info("%s: Register platform-device 'snd-soc-mop500'.\n", __func__);
- platform_device_register(&snd_soc_mop500);
-
- pr_info("Initialize MSP I2S-devices.\n");
- db8500_add_msp_i2s(parent, 0, U8500_MSP0_BASE, IRQ_DB8500_MSP0,
- &msp0_platform_data);
- db8500_add_msp_i2s(parent, 1, U8500_MSP1_BASE, IRQ_DB8500_MSP1,
- &msp1_platform_data);
- db8500_add_msp_i2s(parent, 2, U8500_MSP2_BASE, IRQ_DB8500_MSP2,
- &msp2_platform_data);
- db8500_add_msp_i2s(parent, 3, U8500_MSP3_BASE, IRQ_DB8500_MSP1,
- &msp3_platform_data);
-}
diff --git a/arch/arm/mach-ux500/board-mop500-sdi.c b/arch/arm/mach-ux500/board-mop500-sdi.c
index b3e61a3..26600a1 100644
--- a/arch/arm/mach-ux500/board-mop500-sdi.c
+++ b/arch/arm/mach-ux500/board-mop500-sdi.c
@@ -65,18 +65,6 @@
#endif
};
-static void sdi0_configure(struct device *parent)
-{
- /* Add the device, force v2 to subrevision 1 */
- db8500_add_sdi0(parent, &mop500_sdi0_data, U8500_SDI_V2_PERIPHID);
-}
-
-void mop500_sdi_tc35892_init(struct device *parent)
-{
- mop500_sdi0_data.gpio_cd = GPIO_SDMMC_CD;
- sdi0_configure(parent);
-}
-
/*
* SDI1 (SDIO WLAN)
*/
@@ -178,42 +166,3 @@
.dma_tx_param = &mop500_sdi4_dma_cfg_tx,
#endif
};
-
-void __init mop500_sdi_init(struct device *parent)
-{
- /* PoP:ed eMMC */
- db8500_add_sdi2(parent, &mop500_sdi2_data, U8500_SDI_V2_PERIPHID);
- /* On-board eMMC */
- db8500_add_sdi4(parent, &mop500_sdi4_data, U8500_SDI_V2_PERIPHID);
-
- /*
- * On boards with the TC35892 GPIO expander, sdi0 will finally
- * be added when the TC35892 initializes and calls
- * mop500_sdi_tc35892_init() above.
- */
-}
-
-void __init snowball_sdi_init(struct device *parent)
-{
- /* On Snowball MMC_CAP_SD_HIGHSPEED isn't supported (Hardware issue?) */
- mop500_sdi0_data.capabilities &= ~MMC_CAP_SD_HIGHSPEED;
- /* On-board eMMC */
- db8500_add_sdi4(parent, &mop500_sdi4_data, U8500_SDI_V2_PERIPHID);
- /* External Micro SD slot */
- mop500_sdi0_data.gpio_cd = SNOWBALL_SDMMC_CD_GPIO;
- mop500_sdi0_data.cd_invert = true;
- sdi0_configure(parent);
-}
-
-void __init hrefv60_sdi_init(struct device *parent)
-{
- /* PoP:ed eMMC */
- db8500_add_sdi2(parent, &mop500_sdi2_data, U8500_SDI_V2_PERIPHID);
- /* On-board eMMC */
- db8500_add_sdi4(parent, &mop500_sdi4_data, U8500_SDI_V2_PERIPHID);
- /* External Micro SD slot */
- mop500_sdi0_data.gpio_cd = HREFV60_SDMMC_CD_GPIO;
- sdi0_configure(parent);
- /* WLAN SDIO channel */
- db8500_add_sdi1(parent, &mop500_sdi1_data, U8500_SDI_V2_PERIPHID);
-}
diff --git a/arch/arm/mach-ux500/board-mop500-stuib.c b/arch/arm/mach-ux500/board-mop500-stuib.c
deleted file mode 100644
index 7e1f294..0000000
--- a/arch/arm/mach-ux500/board-mop500-stuib.c
+++ /dev/null
@@ -1,120 +0,0 @@
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * License terms: GNU General Public License (GPL), version 2
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mfd/stmpe.h>
-#include <linux/input/bu21013.h>
-#include <linux/gpio.h>
-#include <linux/interrupt.h>
-#include <linux/i2c.h>
-#include <linux/input/matrix_keypad.h>
-#include <asm/mach-types.h>
-
-#include "board-mop500.h"
-
-/* STMPE/SKE keypad use this key layout */
-static const unsigned int mop500_keymap[] = {
- KEY(2, 5, KEY_END),
- KEY(4, 1, KEY_POWER),
- KEY(3, 5, KEY_VOLUMEDOWN),
- KEY(1, 3, KEY_3),
- KEY(5, 2, KEY_RIGHT),
- KEY(5, 0, KEY_9),
-
- KEY(0, 5, KEY_MENU),
- KEY(7, 6, KEY_ENTER),
- KEY(4, 5, KEY_0),
- KEY(6, 7, KEY_2),
- KEY(3, 4, KEY_UP),
- KEY(3, 3, KEY_DOWN),
-
- KEY(6, 4, KEY_SEND),
- KEY(6, 2, KEY_BACK),
- KEY(4, 2, KEY_VOLUMEUP),
- KEY(5, 5, KEY_1),
- KEY(4, 3, KEY_LEFT),
- KEY(3, 2, KEY_7),
-};
-
-static const struct matrix_keymap_data mop500_keymap_data = {
- .keymap = mop500_keymap,
- .keymap_size = ARRAY_SIZE(mop500_keymap),
-};
-/*
- * STMPE1601
- */
-static struct stmpe_keypad_platform_data stmpe1601_keypad_data = {
- .debounce_ms = 64,
- .scan_count = 8,
- .no_autorepeat = true,
- .keymap_data = &mop500_keymap_data,
-};
-
-static struct stmpe_platform_data stmpe1601_data = {
- .id = 1,
- .blocks = STMPE_BLOCK_KEYPAD,
- .irq_trigger = IRQF_TRIGGER_FALLING,
- .irq_base = MOP500_STMPE1601_IRQ(0),
- .keypad = &stmpe1601_keypad_data,
- .autosleep = true,
- .autosleep_timeout = 1024,
-};
-
-static struct i2c_board_info __initdata mop500_i2c0_devices_stuib[] = {
- {
- I2C_BOARD_INFO("stmpe1601", 0x40),
- .irq = NOMADIK_GPIO_TO_IRQ(218),
- .platform_data = &stmpe1601_data,
- .flags = I2C_CLIENT_WAKE,
- },
-};
-
-/*
- * BU21013 ROHM touchscreen interface on the STUIBs
- */
-
-#define TOUCH_GPIO_PIN 84
-
-#define TOUCH_XMAX 384
-#define TOUCH_YMAX 704
-
-#define PRCMU_CLOCK_OCR 0x1CC
-#define TSC_EXT_CLOCK_9_6MHZ 0x840000
-
-static struct bu21013_platform_device tsc_plat_device = {
- .touch_pin = TOUCH_GPIO_PIN,
- .touch_x_max = TOUCH_XMAX,
- .touch_y_max = TOUCH_YMAX,
- .ext_clk = false,
- .x_flip = false,
- .y_flip = true,
-};
-
-static struct i2c_board_info __initdata u8500_i2c3_devices_stuib[] = {
- {
- I2C_BOARD_INFO("bu21013_tp", 0x5C),
- .platform_data = &tsc_plat_device,
- },
- {
- I2C_BOARD_INFO("bu21013_tp", 0x5D),
- .platform_data = &tsc_plat_device,
- },
-};
-
-void __init mop500_stuib_init(void)
-{
- if (machine_is_hrefv60())
- tsc_plat_device.cs_pin = HREFV60_TOUCH_RST_GPIO;
- else
- tsc_plat_device.cs_pin = GPIO_BU21013_CS;
-
- mop500_uib_i2c_add(0, mop500_i2c0_devices_stuib,
- ARRAY_SIZE(mop500_i2c0_devices_stuib));
-
- mop500_uib_i2c_add(3, u8500_i2c3_devices_stuib,
- ARRAY_SIZE(u8500_i2c3_devices_stuib));
-}
diff --git a/arch/arm/mach-ux500/board-mop500-u8500uib.c b/arch/arm/mach-ux500/board-mop500-u8500uib.c
deleted file mode 100644
index d397c19..0000000
--- a/arch/arm/mach-ux500/board-mop500-u8500uib.c
+++ /dev/null
@@ -1,92 +0,0 @@
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Board data for the U8500 UIB, also known as the New UIB
- * License terms: GNU General Public License (GPL), version 2
- */
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/i2c.h>
-#include <linux/interrupt.h>
-#include <linux/mfd/tc3589x.h>
-#include <linux/input/matrix_keypad.h>
-
-#include "irqs.h"
-
-#include "board-mop500.h"
-
-static struct i2c_board_info __initdata mop500_i2c3_devices_u8500[] = {
- {
- I2C_BOARD_INFO("synaptics_rmi4_i2c", 0x4B),
- .irq = NOMADIK_GPIO_TO_IRQ(84),
- },
-};
-
-/*
- * TC35893
- */
-static const unsigned int u8500_keymap[] = {
- KEY(3, 1, KEY_END),
- KEY(4, 1, KEY_POWER),
- KEY(6, 4, KEY_VOLUMEDOWN),
- KEY(4, 2, KEY_EMAIL),
- KEY(3, 3, KEY_RIGHT),
- KEY(2, 5, KEY_BACKSPACE),
-
- KEY(6, 7, KEY_MENU),
- KEY(5, 0, KEY_ENTER),
- KEY(4, 3, KEY_0),
- KEY(3, 4, KEY_DOT),
- KEY(5, 2, KEY_UP),
- KEY(3, 5, KEY_DOWN),
-
- KEY(4, 5, KEY_SEND),
- KEY(0, 5, KEY_BACK),
- KEY(6, 2, KEY_VOLUMEUP),
- KEY(1, 3, KEY_SPACE),
- KEY(7, 6, KEY_LEFT),
- KEY(5, 5, KEY_SEARCH),
-};
-
-static struct matrix_keymap_data u8500_keymap_data = {
- .keymap = u8500_keymap,
- .keymap_size = ARRAY_SIZE(u8500_keymap),
-};
-
-static struct tc3589x_keypad_platform_data tc35893_data = {
- .krow = TC_KPD_ROWS,
- .kcol = TC_KPD_COLUMNS,
- .debounce_period = TC_KPD_DEBOUNCE_PERIOD,
- .settle_time = TC_KPD_SETTLE_TIME,
- .irqtype = IRQF_TRIGGER_FALLING,
- .enable_wakeup = true,
- .keymap_data = &u8500_keymap_data,
- .no_autorepeat = true,
-};
-
-static struct tc3589x_platform_data tc3589x_keypad_data = {
- .block = TC3589x_BLOCK_KEYPAD,
- .keypad = &tc35893_data,
- .irq_base = MOP500_EGPIO_IRQ_BASE,
-};
-
-static struct i2c_board_info __initdata mop500_i2c0_devices_u8500[] = {
- {
- I2C_BOARD_INFO("tc3589x", 0x44),
- .platform_data = &tc3589x_keypad_data,
- .irq = NOMADIK_GPIO_TO_IRQ(218),
- .flags = I2C_CLIENT_WAKE,
- },
-};
-
-
-void __init mop500_u8500uib_init(void)
-{
- mop500_uib_i2c_add(3, mop500_i2c3_devices_u8500,
- ARRAY_SIZE(mop500_i2c3_devices_u8500));
-
- mop500_uib_i2c_add(0, mop500_i2c0_devices_u8500,
- ARRAY_SIZE(mop500_i2c0_devices_u8500));
-
-}
diff --git a/arch/arm/mach-ux500/board-mop500-uib.c b/arch/arm/mach-ux500/board-mop500-uib.c
deleted file mode 100644
index bdaa422..0000000
--- a/arch/arm/mach-ux500/board-mop500-uib.c
+++ /dev/null
@@ -1,133 +0,0 @@
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
- * License terms: GNU General Public License (GPL), version 2
- */
-
-#define pr_fmt(fmt) "mop500-uib: " fmt
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/i2c.h>
-
-#include "board-mop500.h"
-#include "id.h"
-
-enum mop500_uib {
- STUIB,
- U8500UIB,
-};
-
-struct uib {
- const char *name;
- const char *option;
- void (*init)(void);
-};
-
-static struct uib __initdata mop500_uibs[] = {
- [STUIB] = {
- .name = "ST-UIB",
- .option = "stuib",
- .init = mop500_stuib_init,
- },
- [U8500UIB] = {
- .name = "U8500-UIB",
- .option = "u8500uib",
- .init = mop500_u8500uib_init,
- },
-};
-
-static struct uib *mop500_uib;
-
-static int __init mop500_uib_setup(char *str)
-{
- int i;
-
- for (i = 0; i < ARRAY_SIZE(mop500_uibs); i++) {
- struct uib *uib = &mop500_uibs[i];
-
- if (!strcmp(str, uib->option)) {
- mop500_uib = uib;
- break;
- }
- }
-
- if (i == ARRAY_SIZE(mop500_uibs))
- pr_err("invalid uib= option (%s)\n", str);
-
- return 1;
-}
-__setup("uib=", mop500_uib_setup);
-
-/*
- * The UIBs are detected after the I2C host controllers are registered, so
- * i2c_register_board_info() can't be used.
- */
-void mop500_uib_i2c_add(int busnum, struct i2c_board_info *info,
- unsigned n)
-{
- struct i2c_adapter *adap;
- struct i2c_client *client;
- int i;
-
- adap = i2c_get_adapter(busnum);
- if (!adap) {
- pr_err("failed to get adapter i2c%d\n", busnum);
- return;
- }
-
- for (i = 0; i < n; i++) {
- client = i2c_new_device(adap, &info[i]);
- if (!client)
- pr_err("failed to register %s to i2c%d\n",
- info[i].type, busnum);
- }
-
- i2c_put_adapter(adap);
-}
-
-static void __init __mop500_uib_init(struct uib *uib, const char *why)
-{
- pr_info("%s (%s)\n", uib->name, why);
- uib->init();
-}
-
-/*
- * Detect the UIB attached based on the presence or absence of i2c devices.
- */
-int __init mop500_uib_init(void)
-{
- struct uib *uib = mop500_uib;
- struct i2c_adapter *i2c0;
- int ret;
-
- if (!cpu_is_u8500_family())
- return -ENODEV;
-
- if (uib) {
- __mop500_uib_init(uib, "from uib= boot argument");
- return 0;
- }
-
- i2c0 = i2c_get_adapter(0);
- if (!i2c0) {
- __mop500_uib_init(&mop500_uibs[STUIB],
- "fallback, could not get i2c0");
- return -ENODEV;
- }
-
- /* U8500-UIB has the TC35893 at 0x44 on I2C0, the ST-UIB doesn't. */
- ret = i2c_smbus_xfer(i2c0, 0x44, 0, I2C_SMBUS_WRITE, 0,
- I2C_SMBUS_QUICK, NULL);
- i2c_put_adapter(i2c0);
-
- if (ret == 0)
- uib = &mop500_uibs[U8500UIB];
- else
- uib = &mop500_uibs[STUIB];
-
- __mop500_uib_init(uib, "detected");
-
- return 0;
-}
diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index ad0806e..514d40b 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -14,27 +14,16 @@
#include <linux/platform_device.h>
#include <linux/clk.h>
#include <linux/io.h>
-#include <linux/i2c.h>
-#include <linux/platform_data/i2c-nomadik.h>
#include <linux/platform_data/db8500_thermal.h>
-#include <linux/gpio.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl022.h>
-#include <linux/amba/serial.h>
-#include <linux/spi/spi.h>
#include <linux/mfd/abx500/ab8500.h>
#include <linux/regulator/ab8500.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/driver.h>
-#include <linux/regulator/gpio-regulator.h>
-#include <linux/mfd/tc3589x.h>
#include <linux/mfd/tps6105x.h>
-#include <linux/mfd/abx500/ab8500-gpio.h>
-#include <linux/mfd/abx500/ab8500-codec.h>
#include <linux/platform_data/leds-lp55xx.h>
#include <linux/input.h>
-#include <linux/smsc911x.h>
-#include <linux/gpio_keys.h>
#include <linux/delay.h>
#include <linux/leds.h>
#include <linux/pinctrl/consumer.h>
@@ -46,7 +35,6 @@
#include "setup.h"
#include "devices.h"
#include "irqs.h"
-#include <linux/platform_data/crypto-ux500.h>
#include "ste-dma40-db8500.h"
#include "db8500-regs.h"
@@ -54,401 +42,9 @@
#include "board-mop500.h"
#include "board-mop500-regulators.h"
-static struct gpio_led snowball_led_array[] = {
- {
- .name = "user_led",
- .default_trigger = "heartbeat",
- .gpio = 142,
- },
-};
-
-static struct gpio_led_platform_data snowball_led_data = {
- .leds = snowball_led_array,
- .num_leds = ARRAY_SIZE(snowball_led_array),
-};
-
-static struct platform_device snowball_led_dev = {
- .name = "leds-gpio",
- .dev = {
- .platform_data = &snowball_led_data,
- },
-};
-
-static struct fixed_voltage_config snowball_gpio_en_3v3_data = {
- .supply_name = "EN-3V3",
- .gpio = SNOWBALL_EN_3V3_ETH_GPIO,
- .microvolts = 3300000,
- .enable_high = 1,
- .init_data = &gpio_en_3v3_regulator,
- .startup_delay = 5000, /* 1200us */
-};
-
-static struct platform_device snowball_gpio_en_3v3_regulator_dev = {
- .name = "reg-fixed-voltage",
- .id = 1,
- .dev = {
- .platform_data = &snowball_gpio_en_3v3_data,
- },
-};
-
-/* Dynamically populated. */
-static struct gpio sdi0_reg_gpios[] = {
- { 0, GPIOF_OUT_INIT_LOW, "mmci_vsel" },
-};
-
-static struct gpio_regulator_state sdi0_reg_states[] = {
- { .value = 2900000, .gpios = (0 << 0) },
- { .value = 1800000, .gpios = (1 << 0) },
-};
-
-static struct gpio_regulator_config sdi0_reg_info = {
- .supply_name = "ext-mmc-level-shifter",
- .gpios = sdi0_reg_gpios,
- .nr_gpios = ARRAY_SIZE(sdi0_reg_gpios),
- .states = sdi0_reg_states,
- .nr_states = ARRAY_SIZE(sdi0_reg_states),
- .type = REGULATOR_VOLTAGE,
- .enable_high = 1,
- .enabled_at_boot = 0,
- .init_data = &sdi0_reg_init_data,
- .startup_delay = 100,
-};
-
-static struct platform_device sdi0_regulator = {
- .name = "gpio-regulator",
- .id = -1,
- .dev = {
- .platform_data = &sdi0_reg_info,
- },
-};
-
-static struct abx500_gpio_platform_data ab8500_gpio_pdata = {
- .gpio_base = MOP500_AB8500_PIN_GPIO(1),
-};
-
-/* ab8500-codec */
-static struct ab8500_codec_platform_data ab8500_codec_pdata = {
- .amics = {
- .mic1_type = AMIC_TYPE_DIFFERENTIAL,
- .mic2_type = AMIC_TYPE_DIFFERENTIAL,
- .mic1a_micbias = AMIC_MICBIAS_VAMIC1,
- .mic1b_micbias = AMIC_MICBIAS_VAMIC1,
- .mic2_micbias = AMIC_MICBIAS_VAMIC2
- },
- .ear_cmv = EAR_CMV_0_95V
-};
-
-static struct gpio_keys_button snowball_key_array[] = {
- {
- .gpio = 32,
- .type = EV_KEY,
- .code = KEY_1,
- .desc = "userpb",
- .active_low = 1,
- .debounce_interval = 50,
- .wakeup = 1,
- },
- {
- .gpio = 151,
- .type = EV_KEY,
- .code = KEY_2,
- .desc = "extkb1",
- .active_low = 1,
- .debounce_interval = 50,
- .wakeup = 1,
- },
- {
- .gpio = 152,
- .type = EV_KEY,
- .code = KEY_3,
- .desc = "extkb2",
- .active_low = 1,
- .debounce_interval = 50,
- .wakeup = 1,
- },
- {
- .gpio = 161,
- .type = EV_KEY,
- .code = KEY_4,
- .desc = "extkb3",
- .active_low = 1,
- .debounce_interval = 50,
- .wakeup = 1,
- },
- {
- .gpio = 162,
- .type = EV_KEY,
- .code = KEY_5,
- .desc = "extkb4",
- .active_low = 1,
- .debounce_interval = 50,
- .wakeup = 1,
- },
-};
-
-static struct gpio_keys_platform_data snowball_key_data = {
- .buttons = snowball_key_array,
- .nbuttons = ARRAY_SIZE(snowball_key_array),
-};
-
-static struct platform_device snowball_key_dev = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &snowball_key_data,
- }
-};
-
-static struct smsc911x_platform_config snowball_sbnet_cfg = {
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_HIGH,
- .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
- .flags = SMSC911X_USE_16BIT | SMSC911X_FORCE_INTERNAL_PHY,
- .shift = 1,
-};
-
-static struct resource sbnet_res[] = {
- {
- .name = "smsc911x-memory",
- .start = (0x5000 << 16),
- .end = (0x5000 << 16) + 0xffff,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = NOMADIK_GPIO_TO_IRQ(140),
- .end = NOMADIK_GPIO_TO_IRQ(140),
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
- },
-};
-
-static struct platform_device snowball_sbnet_dev = {
- .name = "smsc911x",
- .num_resources = ARRAY_SIZE(sbnet_res),
- .resource = sbnet_res,
- .dev = {
- .platform_data = &snowball_sbnet_cfg,
- },
-};
-
struct ab8500_platform_data ab8500_platdata = {
.irq_base = MOP500_AB8500_IRQ_BASE,
.regulator = &ab8500_regulator_plat_data,
- .gpio = &ab8500_gpio_pdata,
- .codec = &ab8500_codec_pdata,
-};
-
-static struct platform_device u8500_cpufreq_cooling_device = {
- .name = "db8500-cpufreq-cooling",
-};
-
-/*
- * TPS61052
- */
-
-static struct tps6105x_platform_data mop500_tps61052_data = {
- .mode = TPS6105X_MODE_VOLTAGE,
- .regulator_data = &tps61052_regulator,
-};
-
-/*
- * TC35892
- */
-
-static void mop500_tc35892_init(struct tc3589x *tc3589x, unsigned int base)
-{
- struct device *parent = NULL;
-#if 0
- /* FIXME: Is the sdi actually part of tc3589x? */
- parent = tc3589x->dev;
-#endif
- mop500_sdi_tc35892_init(parent);
-}
-
-static struct tc3589x_gpio_platform_data mop500_tc35892_gpio_data = {
- .gpio_base = MOP500_EGPIO(0),
- .setup = mop500_tc35892_init,
-};
-
-static struct tc3589x_platform_data mop500_tc35892_data = {
- .block = TC3589x_BLOCK_GPIO,
- .gpio = &mop500_tc35892_gpio_data,
- .irq_base = MOP500_EGPIO_IRQ_BASE,
-};
-
-static struct lp55xx_led_config lp5521_pri_led[] = {
- [0] = {
- .chan_nr = 0,
- .led_current = 0x2f,
- .max_current = 0x5f,
- },
- [1] = {
- .chan_nr = 1,
- .led_current = 0x2f,
- .max_current = 0x5f,
- },
- [2] = {
- .chan_nr = 2,
- .led_current = 0x2f,
- .max_current = 0x5f,
- },
-};
-
-static struct lp55xx_platform_data __initdata lp5521_pri_data = {
- .label = "lp5521_pri",
- .led_config = &lp5521_pri_led[0],
- .num_channels = 3,
- .clock_mode = LP55XX_CLOCK_EXT,
-};
-
-static struct lp55xx_led_config lp5521_sec_led[] = {
- [0] = {
- .chan_nr = 0,
- .led_current = 0x2f,
- .max_current = 0x5f,
- },
- [1] = {
- .chan_nr = 1,
- .led_current = 0x2f,
- .max_current = 0x5f,
- },
- [2] = {
- .chan_nr = 2,
- .led_current = 0x2f,
- .max_current = 0x5f,
- },
-};
-
-static struct lp55xx_platform_data __initdata lp5521_sec_data = {
- .label = "lp5521_sec",
- .led_config = &lp5521_sec_led[0],
- .num_channels = 3,
- .clock_mode = LP55XX_CLOCK_EXT,
-};
-
-/* I2C0 devices only available on the first HREF/MOP500 */
-static struct i2c_board_info __initdata mop500_i2c0_devices[] = {
- {
- I2C_BOARD_INFO("tc3589x", 0x42),
- .irq = NOMADIK_GPIO_TO_IRQ(217),
- .platform_data = &mop500_tc35892_data,
- },
- {
- I2C_BOARD_INFO("tps61052", 0x33),
- .platform_data = &mop500_tps61052_data,
- },
-};
-
-static struct i2c_board_info __initdata mop500_i2c2_devices[] = {
- {
- /* lp5521 LED driver, 1st device */
- I2C_BOARD_INFO("lp5521", 0x33),
- .platform_data = &lp5521_pri_data,
- },
- {
- /* lp5521 LED driver, 2st device */
- I2C_BOARD_INFO("lp5521", 0x34),
- .platform_data = &lp5521_sec_data,
- },
- {
- /* Light sensor Rohm BH1780GLI */
- I2C_BOARD_INFO("bh1780", 0x29),
- },
-};
-
-static int __init mop500_i2c_board_init(void)
-{
- if (machine_is_u8500())
- mop500_uib_i2c_add(0, mop500_i2c0_devices,
- ARRAY_SIZE(mop500_i2c0_devices));
- mop500_uib_i2c_add(2, mop500_i2c2_devices,
- ARRAY_SIZE(mop500_i2c2_devices));
- return 0;
-}
-device_initcall(mop500_i2c_board_init);
-
-static void __init mop500_i2c_init(struct device *parent)
-{
- db8500_add_i2c0(parent, NULL);
- db8500_add_i2c1(parent, NULL);
- db8500_add_i2c2(parent, NULL);
- db8500_add_i2c3(parent, NULL);
-}
-
-static struct gpio_keys_button mop500_gpio_keys[] = {
- {
- .desc = "SFH7741 Proximity Sensor",
- .type = EV_SW,
- .code = SW_FRONT_PROXIMITY,
- .active_low = 0,
- .can_disable = 1,
- }
-};
-
-static struct regulator *prox_regulator;
-static int mop500_prox_activate(struct device *dev);
-static void mop500_prox_deactivate(struct device *dev);
-
-static struct gpio_keys_platform_data mop500_gpio_keys_data = {
- .buttons = mop500_gpio_keys,
- .nbuttons = ARRAY_SIZE(mop500_gpio_keys),
- .enable = mop500_prox_activate,
- .disable = mop500_prox_deactivate,
-};
-
-static struct platform_device mop500_gpio_keys_device = {
- .name = "gpio-keys",
- .id = 0,
- .dev = {
- .platform_data = &mop500_gpio_keys_data,
- },
-};
-
-static int mop500_prox_activate(struct device *dev)
-{
- prox_regulator = regulator_get(&mop500_gpio_keys_device.dev,
- "vcc");
- if (IS_ERR(prox_regulator)) {
- dev_err(&mop500_gpio_keys_device.dev,
- "no regulator\n");
- return PTR_ERR(prox_regulator);
- }
-
- return regulator_enable(prox_regulator);
-}
-
-static void mop500_prox_deactivate(struct device *dev)
-{
- regulator_disable(prox_regulator);
- regulator_put(prox_regulator);
-}
-
-static struct cryp_platform_data u8500_cryp1_platform_data = {
- .mem_to_engine = {
- .dir = DMA_MEM_TO_DEV,
- .dev_type = DB8500_DMA_DEV48_CAC1,
- .mode = STEDMA40_MODE_LOGICAL,
- },
- .engine_to_mem = {
- .dir = DMA_DEV_TO_MEM,
- .dev_type = DB8500_DMA_DEV48_CAC1,
- .mode = STEDMA40_MODE_LOGICAL,
- }
-};
-
-static struct stedma40_chan_cfg u8500_hash_dma_cfg_tx = {
- .dir = DMA_MEM_TO_DEV,
- .dev_type = DB8500_DMA_DEV50_HAC1_TX,
- .mode = STEDMA40_MODE_LOGICAL,
-};
-
-static struct hash_platform_data u8500_hash1_platform_data = {
- .mem_to_engine = &u8500_hash_dma_cfg_tx,
- .dma_filter = stedma40_filter,
-};
-
-/* add any platform devices here - TODO */
-static struct platform_device *mop500_platform_devs[] __initdata = {
- &mop500_gpio_keys_device,
- &sdi0_regulator,
};
#ifdef CONFIG_STE_DMA40
@@ -480,236 +76,3 @@
*/
.num_chipselect = 5,
};
-
-static void __init mop500_spi_init(struct device *parent)
-{
- db8500_add_ssp0(parent, &ssp0_plat);
-}
-
-#ifdef CONFIG_STE_DMA40
-static struct stedma40_chan_cfg uart0_dma_cfg_rx = {
- .mode = STEDMA40_MODE_LOGICAL,
- .dir = DMA_DEV_TO_MEM,
- .dev_type = DB8500_DMA_DEV13_UART0,
-};
-
-static struct stedma40_chan_cfg uart0_dma_cfg_tx = {
- .mode = STEDMA40_MODE_LOGICAL,
- .dir = DMA_MEM_TO_DEV,
- .dev_type = DB8500_DMA_DEV13_UART0,
-};
-
-static struct stedma40_chan_cfg uart1_dma_cfg_rx = {
- .mode = STEDMA40_MODE_LOGICAL,
- .dir = DMA_DEV_TO_MEM,
- .dev_type = DB8500_DMA_DEV12_UART1,
-};
-
-static struct stedma40_chan_cfg uart1_dma_cfg_tx = {
- .mode = STEDMA40_MODE_LOGICAL,
- .dir = DMA_MEM_TO_DEV,
- .dev_type = DB8500_DMA_DEV12_UART1,
-};
-
-static struct stedma40_chan_cfg uart2_dma_cfg_rx = {
- .mode = STEDMA40_MODE_LOGICAL,
- .dir = DMA_DEV_TO_MEM,
- .dev_type = DB8500_DMA_DEV11_UART2,
-};
-
-static struct stedma40_chan_cfg uart2_dma_cfg_tx = {
- .mode = STEDMA40_MODE_LOGICAL,
- .dir = DMA_MEM_TO_DEV,
- .dev_type = DB8500_DMA_DEV11_UART2,
-};
-#endif
-
-struct amba_pl011_data uart0_plat = {
-#ifdef CONFIG_STE_DMA40
- .dma_filter = stedma40_filter,
- .dma_rx_param = &uart0_dma_cfg_rx,
- .dma_tx_param = &uart0_dma_cfg_tx,
-#endif
-};
-
-struct amba_pl011_data uart1_plat = {
-#ifdef CONFIG_STE_DMA40
- .dma_filter = stedma40_filter,
- .dma_rx_param = &uart1_dma_cfg_rx,
- .dma_tx_param = &uart1_dma_cfg_tx,
-#endif
-};
-
-struct amba_pl011_data uart2_plat = {
-#ifdef CONFIG_STE_DMA40
- .dma_filter = stedma40_filter,
- .dma_rx_param = &uart2_dma_cfg_rx,
- .dma_tx_param = &uart2_dma_cfg_tx,
-#endif
-};
-
-static void __init mop500_uart_init(struct device *parent)
-{
- db8500_add_uart0(parent, &uart0_plat);
- db8500_add_uart1(parent, &uart1_plat);
- db8500_add_uart2(parent, &uart2_plat);
-}
-
-static void __init u8500_cryp1_hash1_init(struct device *parent)
-{
- db8500_add_cryp1(parent, &u8500_cryp1_platform_data);
- db8500_add_hash1(parent, &u8500_hash1_platform_data);
-}
-
-static struct platform_device *snowball_platform_devs[] __initdata = {
- &snowball_led_dev,
- &snowball_key_dev,
- &snowball_sbnet_dev,
- &snowball_gpio_en_3v3_regulator_dev,
- &u8500_cpufreq_cooling_device,
- &sdi0_regulator,
-};
-
-static void __init mop500_init_machine(void)
-{
- struct device *parent = NULL;
- int i;
-
- platform_device_register(&db8500_prcmu_device);
- mop500_gpio_keys[0].gpio = GPIO_PROX_SENSOR;
-
- sdi0_reg_info.enable_gpio = GPIO_SDMMC_EN;
- sdi0_reg_info.gpios[0].gpio = GPIO_SDMMC_1V8_3V_SEL;
-
- mop500_pinmaps_init();
- parent = u8500_init_devices();
-
- for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++)
- mop500_platform_devs[i]->dev.parent = parent;
-
- platform_add_devices(mop500_platform_devs,
- ARRAY_SIZE(mop500_platform_devs));
-
- mop500_i2c_init(parent);
- mop500_sdi_init(parent);
- mop500_spi_init(parent);
- mop500_audio_init(parent);
- mop500_uart_init(parent);
- u8500_cryp1_hash1_init(parent);
-
- /* This board has full regulator constraints */
- regulator_has_full_constraints();
-}
-
-
-static void __init snowball_init_machine(void)
-{
- struct device *parent = NULL;
- int i;
-
- platform_device_register(&db8500_prcmu_device);
-
- sdi0_reg_info.enable_gpio = SNOWBALL_SDMMC_EN_GPIO;
- sdi0_reg_info.gpios[0].gpio = SNOWBALL_SDMMC_1V8_3V_GPIO;
-
- snowball_pinmaps_init();
- parent = u8500_init_devices();
-
- for (i = 0; i < ARRAY_SIZE(snowball_platform_devs); i++)
- snowball_platform_devs[i]->dev.parent = parent;
-
- platform_add_devices(snowball_platform_devs,
- ARRAY_SIZE(snowball_platform_devs));
-
- mop500_i2c_init(parent);
- snowball_sdi_init(parent);
- mop500_spi_init(parent);
- mop500_audio_init(parent);
- mop500_uart_init(parent);
-
- u8500_cryp1_hash1_init(parent);
-
- /* This board has full regulator constraints */
- regulator_has_full_constraints();
-}
-
-static void __init hrefv60_init_machine(void)
-{
- struct device *parent = NULL;
- int i;
-
- platform_device_register(&db8500_prcmu_device);
- /*
- * The HREFv60 board removed a GPIO expander and routed
- * all these GPIO pins to the internal GPIO controller
- * instead.
- */
- mop500_gpio_keys[0].gpio = HREFV60_PROX_SENSE_GPIO;
-
- sdi0_reg_info.enable_gpio = HREFV60_SDMMC_EN_GPIO;
- sdi0_reg_info.gpios[0].gpio = HREFV60_SDMMC_1V8_3V_GPIO;
-
- hrefv60_pinmaps_init();
- parent = u8500_init_devices();
-
- for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++)
- mop500_platform_devs[i]->dev.parent = parent;
-
- platform_add_devices(mop500_platform_devs,
- ARRAY_SIZE(mop500_platform_devs));
-
- mop500_i2c_init(parent);
- hrefv60_sdi_init(parent);
- mop500_spi_init(parent);
- mop500_audio_init(parent);
- mop500_uart_init(parent);
-
- /* This board has full regulator constraints */
- regulator_has_full_constraints();
-}
-
-MACHINE_START(U8500, "ST-Ericsson MOP500 platform")
- /* Maintainer: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> */
- .atag_offset = 0x100,
- .smp = smp_ops(ux500_smp_ops),
- .map_io = u8500_map_io,
- .init_irq = ux500_init_irq,
- /* we re-use nomadik timer here */
- .init_time = ux500_timer_init,
- .init_machine = mop500_init_machine,
- .init_late = ux500_init_late,
- .restart = ux500_restart,
-MACHINE_END
-
-MACHINE_START(U8520, "ST-Ericsson U8520 Platform HREFP520")
- .atag_offset = 0x100,
- .map_io = u8500_map_io,
- .init_irq = ux500_init_irq,
- .init_time = ux500_timer_init,
- .init_machine = mop500_init_machine,
- .init_late = ux500_init_late,
- .restart = ux500_restart,
-MACHINE_END
-
-MACHINE_START(HREFV60, "ST-Ericsson U8500 Platform HREFv60+")
- .atag_offset = 0x100,
- .smp = smp_ops(ux500_smp_ops),
- .map_io = u8500_map_io,
- .init_irq = ux500_init_irq,
- .init_time = ux500_timer_init,
- .init_machine = hrefv60_init_machine,
- .init_late = ux500_init_late,
- .restart = ux500_restart,
-MACHINE_END
-
-MACHINE_START(SNOWBALL, "Calao Systems Snowball platform")
- .atag_offset = 0x100,
- .smp = smp_ops(ux500_smp_ops),
- .map_io = u8500_map_io,
- .init_irq = ux500_init_irq,
- /* we re-use nomadik timer here */
- .init_time = ux500_timer_init,
- .init_machine = snowball_init_machine,
- .init_late = NULL,
- .restart = ux500_restart,
-MACHINE_END
diff --git a/arch/arm/mach-ux500/board-mop500.h b/arch/arm/mach-ux500/board-mop500.h
index d6fab16..511d6fe 100644
--- a/arch/arm/mach-ux500/board-mop500.h
+++ b/arch/arm/mach-ux500/board-mop500.h
@@ -79,7 +79,6 @@
#define SNOWBALL_EN_3V3_ETH_GPIO MOP500_AB8500_PIN_GPIO(26) /* GPIO26 */
struct device;
-struct i2c_board_info;
extern struct mmci_platform_data mop500_sdi0_data;
extern struct mmci_platform_data mop500_sdi1_data;
extern struct mmci_platform_data mop500_sdi2_data;
@@ -88,25 +87,10 @@
extern struct msp_i2s_platform_data msp1_platform_data;
extern struct msp_i2s_platform_data msp2_platform_data;
extern struct msp_i2s_platform_data msp3_platform_data;
-extern struct arm_pmu_platdata db8500_pmu_platdata;
-extern struct amba_pl011_data uart0_plat;
-extern struct amba_pl011_data uart1_plat;
-extern struct amba_pl011_data uart2_plat;
extern struct pl022_ssp_controller ssp0_plat;
-extern struct stedma40_platform_data dma40_plat_data;
-extern void mop500_sdi_init(struct device *parent);
-extern void snowball_sdi_init(struct device *parent);
-extern void hrefv60_sdi_init(struct device *parent);
-extern void mop500_sdi_tc35892_init(struct device *parent);
-void __init mop500_u8500uib_init(void);
-void __init mop500_stuib_init(void);
void __init mop500_pinmaps_init(void);
void __init snowball_pinmaps_init(void);
void __init hrefv60_pinmaps_init(void);
-void mop500_audio_init(struct device *parent);
-int __init mop500_uib_init(void);
-void mop500_uib_i2c_add(int busnum, struct i2c_board_info *info,
- unsigned n);
#endif
diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c
index 301c346..2e85c1e 100644
--- a/arch/arm/mach-ux500/cpu-db8500.c
+++ b/arch/arm/mach-ux500/cpu-db8500.c
@@ -32,7 +32,6 @@
#include "irqs.h"
#include "devices-db8500.h"
-#include "ste-dma40-db8500.h"
#include "db8500-regs.h"
#include "board-mop500.h"
#include "id.h"
@@ -93,14 +92,6 @@
iotable_init(u8500_io_desc, ARRAY_SIZE(u8500_io_desc));
}
-static struct resource db8500_pmu_resources[] = {
- [0] = {
- .start = IRQ_DB8500_PMU,
- .end = IRQ_DB8500_PMU,
- .flags = IORESOURCE_IRQ,
- },
-};
-
/*
* The PMU IRQ lines of two cores are wired together into a single interrupt.
* Bounce the interrupt to the other core if it's not ours.
@@ -125,54 +116,6 @@
.handle_irq = db8500_pmu_handler,
};
-static struct platform_device db8500_pmu_device = {
- .name = "arm-pmu",
- .id = -1,
- .num_resources = ARRAY_SIZE(db8500_pmu_resources),
- .resource = db8500_pmu_resources,
- .dev.platform_data = &db8500_pmu_platdata,
-};
-
-static struct platform_device *platform_devs[] __initdata = {
- &u8500_dma40_device,
- &db8500_pmu_device,
-};
-
-static resource_size_t __initdata db8500_gpio_base[] = {
- U8500_GPIOBANK0_BASE,
- U8500_GPIOBANK1_BASE,
- U8500_GPIOBANK2_BASE,
- U8500_GPIOBANK3_BASE,
- U8500_GPIOBANK4_BASE,
- U8500_GPIOBANK5_BASE,
- U8500_GPIOBANK6_BASE,
- U8500_GPIOBANK7_BASE,
- U8500_GPIOBANK8_BASE,
-};
-
-static void __init db8500_add_gpios(struct device *parent)
-{
- struct nmk_gpio_platform_data pdata = {
- .supports_sleepmode = true,
- };
-
- dbx500_add_gpios(parent, db8500_gpio_base,
- ARRAY_SIZE(db8500_gpio_base),
- IRQ_DB8500_GPIO0, &pdata);
- dbx500_add_pinctrl(parent, "pinctrl-db8500", U8500_PRCMU_BASE);
-}
-
-static int usb_db8500_dma_cfg[] = {
- DB8500_DMA_DEV38_USB_OTG_IEP_AND_OEP_1_9,
- DB8500_DMA_DEV37_USB_OTG_IEP_AND_OEP_2_10,
- DB8500_DMA_DEV36_USB_OTG_IEP_AND_OEP_3_11,
- DB8500_DMA_DEV19_USB_OTG_IEP_AND_OEP_4_12,
- DB8500_DMA_DEV18_USB_OTG_IEP_AND_OEP_5_13,
- DB8500_DMA_DEV17_USB_OTG_IEP_AND_OEP_6_14,
- DB8500_DMA_DEV16_USB_OTG_IEP_AND_OEP_7_15,
- DB8500_DMA_DEV39_USB_OTG_IEP_AND_OEP_8
-};
-
static const char *db8500_read_soc_id(void)
{
void __iomem *uid = __io_address(U8500_BB_UID_BASE);
@@ -192,60 +135,22 @@
return ux500_soc_device_init(soc_id);
}
-/*
- * This function is called from the board init
- */
-struct device * __init u8500_init_devices(void)
-{
- struct device *parent;
- int i;
-
- parent = db8500_soc_device_init();
-
- db8500_add_rtc(parent);
- db8500_add_gpios(parent);
- db8500_add_usb(parent, usb_db8500_dma_cfg, usb_db8500_dma_cfg);
-
- for (i = 0; i < ARRAY_SIZE(platform_devs); i++)
- platform_devs[i]->dev.parent = parent;
-
- platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs));
-
- return parent;
-}
-
#ifdef CONFIG_MACH_UX500_DT
static struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = {
/* Requires call-back bindings. */
OF_DEV_AUXDATA("arm,cortex-a9-pmu", 0, "arm-pmu", &db8500_pmu_platdata),
/* Requires DMA bindings. */
- OF_DEV_AUXDATA("arm,pl011", 0x80120000, "uart0", NULL),
- OF_DEV_AUXDATA("arm,pl011", 0x80121000, "uart1", NULL),
- OF_DEV_AUXDATA("arm,pl011", 0x80007000, "uart2", NULL),
- OF_DEV_AUXDATA("arm,pl022", 0x80002000, "ssp0", &ssp0_plat),
- OF_DEV_AUXDATA("arm,pl18x", 0x80126000, "sdi0", NULL),
- OF_DEV_AUXDATA("arm,pl18x", 0x80118000, "sdi1", NULL),
- OF_DEV_AUXDATA("arm,pl18x", 0x80005000, "sdi2", NULL),
- OF_DEV_AUXDATA("arm,pl18x", 0x80114000, "sdi4", NULL),
- /* Requires clock name bindings. */
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8012e000, "gpio.0", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8012e080, "gpio.1", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e000, "gpio.2", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e080, "gpio.3", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e100, "gpio.4", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e180, "gpio.5", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8011e000, "gpio.6", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8011e080, "gpio.7", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0xa03fe000, "gpio.8", NULL),
- OF_DEV_AUXDATA("st,nomadik-i2c", 0x80004000, "nmk-i2c.0", NULL),
- OF_DEV_AUXDATA("st,nomadik-i2c", 0x80122000, "nmk-i2c.1", NULL),
- OF_DEV_AUXDATA("st,nomadik-i2c", 0x80128000, "nmk-i2c.2", NULL),
- OF_DEV_AUXDATA("st,nomadik-i2c", 0x80110000, "nmk-i2c.3", NULL),
- OF_DEV_AUXDATA("st,nomadik-i2c", 0x8012a000, "nmk-i2c.4", NULL),
- OF_DEV_AUXDATA("stericsson,db8500-musb", 0xa03e0000, "musb-ux500.0", NULL),
+ OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80123000,
+ "ux500-msp-i2s.0", &msp0_platform_data),
+ OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80124000,
+ "ux500-msp-i2s.1", &msp1_platform_data),
+ OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80117000,
+ "ux500-msp-i2s.2", &msp2_platform_data),
+ OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80125000,
+ "ux500-msp-i2s.3", &msp3_platform_data),
+ /* Requires non-DT:able platform data. */
OF_DEV_AUXDATA("stericsson,db8500-prcmu", 0x80157000, "db8500-prcmu",
&db8500_prcmu_pdata),
- OF_DEV_AUXDATA("smsc,lan9115", 0x50000000, "smsc911x.0", NULL),
OF_DEV_AUXDATA("stericsson,ux500-cryp", 0xa03cb000, "cryp1", NULL),
OF_DEV_AUXDATA("stericsson,ux500-hash", 0xa03c2000, "hash1", NULL),
OF_DEV_AUXDATA("stericsson,snd-soc-mop500", 0, "snd-soc-mop500.0",
@@ -253,17 +158,6 @@
/* Requires device name bindings. */
OF_DEV_AUXDATA("stericsson,db8500-pinctrl", U8500_PRCMU_BASE,
"pinctrl-db8500", NULL),
- /* Requires clock name and DMA bindings. */
- OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80123000,
- "ux500-msp-i2s.0", &msp0_platform_data),
- OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80124000,
- "ux500-msp-i2s.1", &msp1_platform_data),
- OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80117000,
- "ux500-msp-i2s.2", &msp2_platform_data),
- OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80125000,
- "ux500-msp-i2s.3", &msp3_platform_data),
- /* Requires clock name bindings and channel address lookup table. */
- OF_DEV_AUXDATA("stericsson,db8500-dma40", 0x801C0000, "dma40.0", NULL),
{},
};
diff --git a/arch/arm/mach-ux500/cpu.c b/arch/arm/mach-ux500/cpu.c
index 5d7eebc..f84d439 100644
--- a/arch/arm/mach-ux500/cpu.c
+++ b/arch/arm/mach-ux500/cpu.c
@@ -78,9 +78,17 @@
if (cpu_is_u8500_family()) {
prcmu_early_init(U8500_PRCMU_BASE, SZ_8K - 1);
ux500_pm_init(U8500_PRCMU_BASE, SZ_8K - 1);
- u8500_clk_init(U8500_CLKRST1_BASE, U8500_CLKRST2_BASE,
- U8500_CLKRST3_BASE, U8500_CLKRST5_BASE,
- U8500_CLKRST6_BASE);
+
+ if (of_have_populated_dt())
+ u8500_of_clk_init(U8500_CLKRST1_BASE,
+ U8500_CLKRST2_BASE,
+ U8500_CLKRST3_BASE,
+ U8500_CLKRST5_BASE,
+ U8500_CLKRST6_BASE);
+ else
+ u8500_clk_init(U8500_CLKRST1_BASE, U8500_CLKRST2_BASE,
+ U8500_CLKRST3_BASE, U8500_CLKRST5_BASE,
+ U8500_CLKRST6_BASE);
} else if (cpu_is_u9540()) {
prcmu_early_init(U8500_PRCMU_BASE, SZ_8K - 1);
ux500_pm_init(U8500_PRCMU_BASE, SZ_8K - 1);
@@ -96,11 +104,6 @@
}
}
-void __init ux500_init_late(void)
-{
- mop500_uib_init();
-}
-
static const char * __init ux500_get_machine(void)
{
return kasprintf(GFP_KERNEL, "DB%4x", dbx500_partnumber());
diff --git a/arch/arm/mach-ux500/devices-common.c b/arch/arm/mach-ux500/devices-common.c
deleted file mode 100644
index f71b3d7..0000000
--- a/arch/arm/mach-ux500/devices-common.c
+++ /dev/null
@@ -1,60 +0,0 @@
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
- * License terms: GNU General Public License (GPL), version 2.
- */
-
-#include <linux/kernel.h>
-#include <linux/dma-mapping.h>
-#include <linux/err.h>
-#include <linux/irq.h>
-#include <linux/slab.h>
-#include <linux/platform_device.h>
-#include <linux/platform_data/pinctrl-nomadik.h>
-
-#include "irqs.h"
-
-#include "devices-common.h"
-
-static struct platform_device *
-dbx500_add_gpio(struct device *parent, int id, resource_size_t addr, int irq,
- struct nmk_gpio_platform_data *pdata)
-{
- struct resource resources[] = {
- {
- .start = addr,
- .end = addr + 127,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = irq,
- .end = irq,
- .flags = IORESOURCE_IRQ,
- }
- };
-
- return platform_device_register_resndata(
- parent,
- "gpio",
- id,
- resources,
- ARRAY_SIZE(resources),
- pdata,
- sizeof(*pdata));
-}
-
-void dbx500_add_gpios(struct device *parent, resource_size_t *base, int num,
- int irq, struct nmk_gpio_platform_data *pdata)
-{
- int first = 0;
- int i;
-
- for (i = 0; i < num; i++, first += 32, irq++) {
- pdata->first_gpio = first;
- pdata->first_irq = NOMADIK_GPIO_TO_IRQ(first);
- pdata->num_gpio = 32;
-
- dbx500_add_gpio(parent, i, base[i], irq, pdata);
- }
-}
diff --git a/arch/arm/mach-ux500/devices-common.h b/arch/arm/mach-ux500/devices-common.h
deleted file mode 100644
index 96fa4ac..0000000
--- a/arch/arm/mach-ux500/devices-common.h
+++ /dev/null
@@ -1,149 +0,0 @@
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
- * License terms: GNU General Public License (GPL), version 2.
- */
-
-#ifndef __DEVICES_COMMON_H
-#define __DEVICES_COMMON_H
-
-#include <linux/platform_device.h>
-#include <linux/dma-mapping.h>
-#include <linux/sys_soc.h>
-#include <linux/amba/bus.h>
-#include <linux/platform_data/i2c-nomadik.h>
-#include <linux/platform_data/crypto-ux500.h>
-
-struct spi_master_cntlr;
-
-static inline struct amba_device *
-dbx500_add_msp_spi(struct device *parent, const char *name,
- resource_size_t base, int irq,
- struct spi_master_cntlr *pdata)
-{
- return amba_ahb_device_add(parent, name, base, SZ_4K, irq, 0,
- pdata, 0);
-}
-
-static inline struct amba_device *
-dbx500_add_spi(struct device *parent, const char *name, resource_size_t base,
- int irq, struct spi_master_cntlr *pdata,
- u32 periphid)
-{
- return amba_ahb_device_add(parent, name, base, SZ_4K, irq, 0,
- pdata, periphid);
-}
-
-struct mmci_platform_data;
-
-static inline struct amba_device *
-dbx500_add_sdi(struct device *parent, const char *name, resource_size_t base,
- int irq, struct mmci_platform_data *pdata, u32 periphid)
-{
- return amba_ahb_device_add(parent, name, base, SZ_4K, irq, 0,
- pdata, periphid);
-}
-
-struct amba_pl011_data;
-
-static inline struct amba_device *
-dbx500_add_uart(struct device *parent, const char *name, resource_size_t base,
- int irq, struct amba_pl011_data *pdata)
-{
- return amba_ahb_device_add(parent, name, base, SZ_4K, irq, 0, pdata, 0);
-}
-
-struct nmk_i2c_controller;
-
-static inline struct amba_device *
-dbx500_add_i2c(struct device *parent, int id, resource_size_t base, int irq,
- struct nmk_i2c_controller *data)
-{
- /* Conjure a name similar to what the platform device used to have */
- char name[16];
-
- snprintf(name, sizeof(name), "nmk-i2c.%d", id);
- return amba_apb_device_add(parent, name, base, SZ_4K, irq, 0, data, 0);
-}
-
-static inline struct amba_device *
-dbx500_add_rtc(struct device *parent, resource_size_t base, int irq)
-{
- return amba_apb_device_add(parent, "rtc-pl031", base, SZ_4K, irq,
- 0, NULL, 0);
-}
-
-struct cryp_platform_data;
-
-static inline struct platform_device *
-dbx500_add_cryp1(struct device *parent, int id, resource_size_t base, int irq,
- struct cryp_platform_data *pdata)
-{
- struct resource res[] = {
- DEFINE_RES_MEM(base, SZ_4K),
- DEFINE_RES_IRQ(irq),
- };
-
- struct platform_device_info pdevinfo = {
- .parent = parent,
- .name = "cryp1",
- .id = id,
- .res = res,
- .num_res = ARRAY_SIZE(res),
- .data = pdata,
- .size_data = sizeof(*pdata),
- .dma_mask = DMA_BIT_MASK(32),
- };
-
- return platform_device_register_full(&pdevinfo);
-}
-
-struct hash_platform_data;
-
-static inline struct platform_device *
-dbx500_add_hash1(struct device *parent, int id, resource_size_t base,
- struct hash_platform_data *pdata)
-{
- struct resource res[] = {
- DEFINE_RES_MEM(base, SZ_4K),
- };
-
- struct platform_device_info pdevinfo = {
- .parent = parent,
- .name = "hash1",
- .id = id,
- .res = res,
- .num_res = ARRAY_SIZE(res),
- .data = pdata,
- .size_data = sizeof(*pdata),
- .dma_mask = DMA_BIT_MASK(32),
- };
-
- return platform_device_register_full(&pdevinfo);
-}
-
-struct nmk_gpio_platform_data;
-
-void dbx500_add_gpios(struct device *parent, resource_size_t *base, int num,
- int irq, struct nmk_gpio_platform_data *pdata);
-
-static inline void
-dbx500_add_pinctrl(struct device *parent, const char *name,
- resource_size_t base)
-{
- struct resource res[] = {
- DEFINE_RES_MEM(base, SZ_8K),
- };
- struct platform_device_info pdevinfo = {
- .parent = parent,
- .name = name,
- .id = -1,
- .res = res,
- .num_res = ARRAY_SIZE(res),
- };
-
- platform_device_register_full(&pdevinfo);
-}
-
-#endif
diff --git a/arch/arm/mach-ux500/devices-db8500.c b/arch/arm/mach-ux500/devices-db8500.c
index bc31606..c59f89d 100644
--- a/arch/arm/mach-ux500/devices-db8500.c
+++ b/arch/arm/mach-ux500/devices-db8500.c
@@ -9,10 +9,8 @@
#include <linux/platform_device.h>
#include <linux/interrupt.h>
#include <linux/io.h>
-#include <linux/gpio.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl022.h>
-#include <linux/platform_data/dma-ste-dma40.h>
#include <linux/mfd/dbx500-prcmu.h>
#include "setup.h"
@@ -20,62 +18,6 @@
#include "db8500-regs.h"
#include "devices-db8500.h"
-#include "ste-dma40-db8500.h"
-
-static struct resource dma40_resources[] = {
- [0] = {
- .start = U8500_DMA_BASE,
- .end = U8500_DMA_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- .name = "base",
- },
- [1] = {
- .start = U8500_DMA_LCPA_BASE,
- .end = U8500_DMA_LCPA_BASE + 2 * SZ_1K - 1,
- .flags = IORESOURCE_MEM,
- .name = "lcpa",
- },
- [2] = {
- .start = IRQ_DB8500_DMA,
- .end = IRQ_DB8500_DMA,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-struct stedma40_platform_data dma40_plat_data = {
- .disabled_channels = {-1},
-};
-
-struct platform_device u8500_dma40_device = {
- .dev = {
- .platform_data = &dma40_plat_data,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .name = "dma40",
- .id = 0,
- .num_resources = ARRAY_SIZE(dma40_resources),
- .resource = dma40_resources
-};
-
-struct resource keypad_resources[] = {
- [0] = {
- .start = U8500_SKE_BASE,
- .end = U8500_SKE_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_DB8500_KB,
- .end = IRQ_DB8500_KB,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device u8500_ske_keypad_device = {
- .name = "nmk-ske-keypad",
- .id = -1,
- .num_resources = ARRAY_SIZE(keypad_resources),
- .resource = keypad_resources,
-};
struct prcmu_pdata db8500_prcmu_pdata = {
.ab_platdata = &ab8500_platdata,
@@ -84,39 +26,3 @@
.version_offset = DB8500_PRCMU_FW_VERSION_OFFSET,
.legacy_offset = DB8500_PRCMU_LEGACY_OFFSET,
};
-
-static struct resource db8500_prcmu_res[] = {
- {
- .name = "prcmu",
- .start = U8500_PRCMU_BASE,
- .end = U8500_PRCMU_BASE + SZ_8K - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- .name = "prcmu-tcdm",
- .start = U8500_PRCMU_TCDM_BASE,
- .end = U8500_PRCMU_TCDM_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- .name = "irq",
- .start = IRQ_DB8500_PRCMU1,
- .end = IRQ_DB8500_PRCMU1,
- .flags = IORESOURCE_IRQ,
- },
- {
- .name = "prcmu-tcpm",
- .start = U8500_PRCMU_TCPM_BASE,
- .end = U8500_PRCMU_TCPM_BASE + SZ_32K - 1,
- .flags = IORESOURCE_MEM,
- },
-};
-
-struct platform_device db8500_prcmu_device = {
- .name = "db8500-prcmu",
- .resource = db8500_prcmu_res,
- .num_resources = ARRAY_SIZE(db8500_prcmu_res),
- .dev = {
- .platform_data = &db8500_prcmu_pdata,
- },
-};
diff --git a/arch/arm/mach-ux500/devices-db8500.h b/arch/arm/mach-ux500/devices-db8500.h
index 3219983..b8ffc99 100644
--- a/arch/arm/mach-ux500/devices-db8500.h
+++ b/arch/arm/mach-ux500/devices-db8500.h
@@ -8,122 +8,12 @@
#ifndef __DEVICES_DB8500_H
#define __DEVICES_DB8500_H
-#include <linux/platform_data/usb-musb-ux500.h>
#include "irqs.h"
#include "db8500-regs.h"
-#include "devices-common.h"
-struct ske_keypad_platform_data;
-struct pl022_ssp_controller;
struct platform_device;
extern struct ab8500_platform_data ab8500_platdata;
extern struct prcmu_pdata db8500_prcmu_pdata;
-extern struct platform_device db8500_prcmu_device;
-static inline struct platform_device *
-db8500_add_ske_keypad(struct device *parent,
- struct ske_keypad_platform_data *pdata,
- size_t size)
-{
- struct resource resources[] = {
- DEFINE_RES_MEM(U8500_SKE_BASE, SZ_4K),
- DEFINE_RES_IRQ(IRQ_DB8500_KB),
- };
-
- return platform_device_register_resndata(parent, "nmk-ske-keypad", -1,
- resources, 2, pdata, size);
-}
-
-static inline struct amba_device *
-db8500_add_ssp(struct device *parent, const char *name, resource_size_t base,
- int irq, struct pl022_ssp_controller *pdata)
-{
- return amba_ahb_device_add(parent, name, base, SZ_4K, irq, 0, pdata, 0);
-}
-
-#define db8500_add_i2c0(parent, pdata) \
- dbx500_add_i2c(parent, 0, U8500_I2C0_BASE, IRQ_DB8500_I2C0, pdata)
-#define db8500_add_i2c1(parent, pdata) \
- dbx500_add_i2c(parent, 1, U8500_I2C1_BASE, IRQ_DB8500_I2C1, pdata)
-#define db8500_add_i2c2(parent, pdata) \
- dbx500_add_i2c(parent, 2, U8500_I2C2_BASE, IRQ_DB8500_I2C2, pdata)
-#define db8500_add_i2c3(parent, pdata) \
- dbx500_add_i2c(parent, 3, U8500_I2C3_BASE, IRQ_DB8500_I2C3, pdata)
-#define db8500_add_i2c4(parent, pdata) \
- dbx500_add_i2c(parent, 4, U8500_I2C4_BASE, IRQ_DB8500_I2C4, pdata)
-
-#define db8500_add_msp0_spi(parent, pdata) \
- dbx500_add_msp_spi(parent, "msp0", U8500_MSP0_BASE, \
- IRQ_DB8500_MSP0, pdata)
-#define db8500_add_msp1_spi(parent, pdata) \
- dbx500_add_msp_spi(parent, "msp1", U8500_MSP1_BASE, \
- IRQ_DB8500_MSP1, pdata)
-#define db8500_add_msp2_spi(parent, pdata) \
- dbx500_add_msp_spi(parent, "msp2", U8500_MSP2_BASE, \
- IRQ_DB8500_MSP2, pdata)
-#define db8500_add_msp3_spi(parent, pdata) \
- dbx500_add_msp_spi(parent, "msp3", U8500_MSP3_BASE, \
- IRQ_DB8500_MSP1, pdata)
-
-#define db8500_add_rtc(parent) \
- dbx500_add_rtc(parent, U8500_RTC_BASE, IRQ_DB8500_RTC);
-
-#define db8500_add_usb(parent, rx_cfg, tx_cfg) \
- ux500_add_usb(parent, U8500_USBOTG_BASE, \
- IRQ_DB8500_USBOTG, rx_cfg, tx_cfg)
-
-#define db8500_add_sdi0(parent, pdata, pid) \
- dbx500_add_sdi(parent, "sdi0", U8500_SDI0_BASE, \
- IRQ_DB8500_SDMMC0, pdata, pid)
-#define db8500_add_sdi1(parent, pdata, pid) \
- dbx500_add_sdi(parent, "sdi1", U8500_SDI1_BASE, \
- IRQ_DB8500_SDMMC1, pdata, pid)
-#define db8500_add_sdi2(parent, pdata, pid) \
- dbx500_add_sdi(parent, "sdi2", U8500_SDI2_BASE, \
- IRQ_DB8500_SDMMC2, pdata, pid)
-#define db8500_add_sdi3(parent, pdata, pid) \
- dbx500_add_sdi(parent, "sdi3", U8500_SDI3_BASE, \
- IRQ_DB8500_SDMMC3, pdata, pid)
-#define db8500_add_sdi4(parent, pdata, pid) \
- dbx500_add_sdi(parent, "sdi4", U8500_SDI4_BASE, \
- IRQ_DB8500_SDMMC4, pdata, pid)
-#define db8500_add_sdi5(parent, pdata, pid) \
- dbx500_add_sdi(parent, "sdi5", U8500_SDI5_BASE, \
- IRQ_DB8500_SDMMC5, pdata, pid)
-
-#define db8500_add_ssp0(parent, pdata) \
- db8500_add_ssp(parent, "ssp0", U8500_SSP0_BASE, \
- IRQ_DB8500_SSP0, pdata)
-#define db8500_add_ssp1(parent, pdata) \
- db8500_add_ssp(parent, "ssp1", U8500_SSP1_BASE, \
- IRQ_DB8500_SSP1, pdata)
-
-#define db8500_add_spi0(parent, pdata) \
- dbx500_add_spi(parent, "spi0", U8500_SPI0_BASE, \
- IRQ_DB8500_SPI0, pdata, 0)
-#define db8500_add_spi1(parent, pdata) \
- dbx500_add_spi(parent, "spi1", U8500_SPI1_BASE, \
- IRQ_DB8500_SPI1, pdata, 0)
-#define db8500_add_spi2(parent, pdata) \
- dbx500_add_spi(parent, "spi2", U8500_SPI2_BASE, \
- IRQ_DB8500_SPI2, pdata, 0)
-#define db8500_add_spi3(parent, pdata) \
- dbx500_add_spi(parent, "spi3", U8500_SPI3_BASE, \
- IRQ_DB8500_SPI3, pdata, 0)
-
-#define db8500_add_uart0(parent, pdata) \
- dbx500_add_uart(parent, "uart0", U8500_UART0_BASE, \
- IRQ_DB8500_UART0, pdata)
-#define db8500_add_uart1(parent, pdata) \
- dbx500_add_uart(parent, "uart1", U8500_UART1_BASE, \
- IRQ_DB8500_UART1, pdata)
-#define db8500_add_uart2(parent, pdata) \
- dbx500_add_uart(parent, "uart2", U8500_UART2_BASE, \
- IRQ_DB8500_UART2, pdata)
-
-#define db8500_add_cryp1(parent, pdata) \
- dbx500_add_cryp1(parent, -1, U8500_CRYP1_BASE, IRQ_DB8500_CRYP1, pdata)
-#define db8500_add_hash1(parent, pdata) \
- dbx500_add_hash1(parent, -1, U8500_HASH1_BASE, pdata)
#endif
diff --git a/arch/arm/mach-ux500/devices.h b/arch/arm/mach-ux500/devices.h
index cbc6f1e..5bca7c6 100644
--- a/arch/arm/mach-ux500/devices.h
+++ b/arch/arm/mach-ux500/devices.h
@@ -10,14 +10,6 @@
struct platform_device;
struct amba_device;
-extern struct platform_device u8500_gpio_devs[];
-
extern struct amba_device ux500_pl031_device;
-extern struct platform_device ux500_hash1_device;
-extern struct platform_device ux500_cryp1_device;
-
-extern struct platform_device u8500_dma40_device;
-extern struct platform_device ux500_ske_keypad_device;
-
#endif
diff --git a/arch/arm/mach-ux500/setup.h b/arch/arm/mach-ux500/setup.h
index 656324a..bdb3564 100644
--- a/arch/arm/mach-ux500/setup.h
+++ b/arch/arm/mach-ux500/setup.h
@@ -24,7 +24,6 @@
extern struct device * __init u8500_init_devices(void);
extern void __init ux500_init_irq(void);
-extern void __init ux500_init_late(void);
extern struct device *ux500_soc_device_init(const char *soc_id);
diff --git a/arch/arm/mach-ux500/timer.c b/arch/arm/mach-ux500/timer.c
index b6bd0ef..05a4ff7 100644
--- a/arch/arm/mach-ux500/timer.c
+++ b/arch/arm/mach-ux500/timer.c
@@ -97,8 +97,8 @@
* sched_clock with higher rating then MTU since is always-on.
*
*/
-
- nmdk_timer_init(mtu_timer_base, IRQ_MTU0);
+ if (!of_have_populated_dt())
+ nmdk_timer_init(mtu_timer_base, IRQ_MTU0);
clksrc_dbx500_prcmu_init(prcmu_timer_base);
ux500_twd_init();
}
diff --git a/arch/arm/mach-ux500/usb.c b/arch/arm/mach-ux500/usb.c
deleted file mode 100644
index b7bd8d3..0000000
--- a/arch/arm/mach-ux500/usb.c
+++ /dev/null
@@ -1,135 +0,0 @@
-/*
- * Copyright (C) ST-Ericsson SA 2011
- *
- * Author: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
- * License terms: GNU General Public License (GPL) version 2
- */
-#include <linux/platform_device.h>
-#include <linux/usb/musb.h>
-#include <linux/dma-mapping.h>
-#include <linux/platform_data/usb-musb-ux500.h>
-#include <linux/platform_data/dma-ste-dma40.h>
-
-#include "db8500-regs.h"
-
-#define MUSB_DMA40_RX_CH { \
- .mode = STEDMA40_MODE_LOGICAL, \
- .dir = DMA_DEV_TO_MEM, \
- }
-
-#define MUSB_DMA40_TX_CH { \
- .mode = STEDMA40_MODE_LOGICAL, \
- .dir = DMA_MEM_TO_DEV, \
- }
-
-static struct stedma40_chan_cfg musb_dma_rx_ch[UX500_MUSB_DMA_NUM_RX_TX_CHANNELS]
- = {
- MUSB_DMA40_RX_CH,
- MUSB_DMA40_RX_CH,
- MUSB_DMA40_RX_CH,
- MUSB_DMA40_RX_CH,
- MUSB_DMA40_RX_CH,
- MUSB_DMA40_RX_CH,
- MUSB_DMA40_RX_CH,
- MUSB_DMA40_RX_CH
-};
-
-static struct stedma40_chan_cfg musb_dma_tx_ch[UX500_MUSB_DMA_NUM_RX_TX_CHANNELS]
- = {
- MUSB_DMA40_TX_CH,
- MUSB_DMA40_TX_CH,
- MUSB_DMA40_TX_CH,
- MUSB_DMA40_TX_CH,
- MUSB_DMA40_TX_CH,
- MUSB_DMA40_TX_CH,
- MUSB_DMA40_TX_CH,
- MUSB_DMA40_TX_CH,
-};
-
-static void *ux500_dma_rx_param_array[UX500_MUSB_DMA_NUM_RX_TX_CHANNELS] = {
- &musb_dma_rx_ch[0],
- &musb_dma_rx_ch[1],
- &musb_dma_rx_ch[2],
- &musb_dma_rx_ch[3],
- &musb_dma_rx_ch[4],
- &musb_dma_rx_ch[5],
- &musb_dma_rx_ch[6],
- &musb_dma_rx_ch[7]
-};
-
-static void *ux500_dma_tx_param_array[UX500_MUSB_DMA_NUM_RX_TX_CHANNELS] = {
- &musb_dma_tx_ch[0],
- &musb_dma_tx_ch[1],
- &musb_dma_tx_ch[2],
- &musb_dma_tx_ch[3],
- &musb_dma_tx_ch[4],
- &musb_dma_tx_ch[5],
- &musb_dma_tx_ch[6],
- &musb_dma_tx_ch[7]
-};
-
-static struct ux500_musb_board_data musb_board_data = {
- .dma_rx_param_array = ux500_dma_rx_param_array,
- .dma_tx_param_array = ux500_dma_tx_param_array,
- .dma_filter = stedma40_filter,
-};
-
-static struct musb_hdrc_platform_data musb_platform_data = {
- .mode = MUSB_OTG,
- .board_data = &musb_board_data,
-};
-
-static struct resource usb_resources[] = {
- [0] = {
- .name = "usb-mem",
- .flags = IORESOURCE_MEM,
- },
-
- [1] = {
- .name = "mc", /* hard-coded in musb */
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device ux500_musb_device = {
- .name = "musb-ux500",
- .id = 0,
- .dev = {
- .platform_data = &musb_platform_data,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(usb_resources),
- .resource = usb_resources,
-};
-
-static inline void ux500_usb_dma_update_rx_ch_config(int *dev_type)
-{
- u32 idx;
-
- for (idx = 0; idx < UX500_MUSB_DMA_NUM_RX_TX_CHANNELS; idx++)
- musb_dma_rx_ch[idx].dev_type = dev_type[idx];
-}
-
-static inline void ux500_usb_dma_update_tx_ch_config(int *dev_type)
-{
- u32 idx;
-
- for (idx = 0; idx < UX500_MUSB_DMA_NUM_RX_TX_CHANNELS; idx++)
- musb_dma_tx_ch[idx].dev_type = dev_type[idx];
-}
-
-void ux500_add_usb(struct device *parent, resource_size_t base, int irq,
- int *dma_rx_cfg, int *dma_tx_cfg)
-{
- ux500_musb_device.resource[0].start = base;
- ux500_musb_device.resource[0].end = base + SZ_64K - 1;
- ux500_musb_device.resource[1].start = irq;
- ux500_musb_device.resource[1].end = irq;
-
- ux500_usb_dma_update_rx_ch_config(dma_rx_cfg);
- ux500_usb_dma_update_tx_ch_config(dma_tx_cfg);
-
- ux500_musb_device.dev.parent = parent;
-
- platform_device_register(&ux500_musb_device);
-}
diff --git a/arch/arm/plat-samsung/include/plat/cpu.h b/arch/arm/plat-samsung/include/plat/cpu.h
index 4fb1f03..335beb3 100644
--- a/arch/arm/plat-samsung/include/plat/cpu.h
+++ b/arch/arm/plat-samsung/include/plat/cpu.h
@@ -87,8 +87,12 @@
#endif
#if defined(CONFIG_CPU_S3C6400) || defined(CONFIG_CPU_S3C6410)
+# define soc_is_s3c6400() is_samsung_s3c6400()
+# define soc_is_s3c6410() is_samsung_s3c6410()
# define soc_is_s3c64xx() (is_samsung_s3c6400() || is_samsung_s3c6410())
#else
+# define soc_is_s3c6400() 0
+# define soc_is_s3c6410() 0
# define soc_is_s3c64xx() 0
#endif
diff --git a/arch/arm/plat-samsung/init.c b/arch/arm/plat-samsung/init.c
index 50a3ea0..aa9511b 100644
--- a/arch/arm/plat-samsung/init.c
+++ b/arch/arm/plat-samsung/init.c
@@ -11,12 +11,18 @@
* published by the Free Software Foundation.
*/
+/*
+ * NOTE: Code in this file is not used on S3C64xx when booting with
+ * Device Tree support.
+ */
+
#include <linux/init.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
+#include <linux/of.h>
#include <mach/hardware.h>
@@ -148,8 +154,12 @@
// do the correct init for cpu
- if (cpu == NULL)
+ if (cpu == NULL) {
+ /* Not needed when booting with device tree. */
+ if (of_have_populated_dt())
+ return 0;
panic("s3c_arch_init: NULL cpu\n");
+ }
ret = (cpu->init)();
if (ret != 0)
diff --git a/arch/mips/include/asm/jump_label.h b/arch/mips/include/asm/jump_label.h
index 4d6d77e..e194f95 100644
--- a/arch/mips/include/asm/jump_label.h
+++ b/arch/mips/include/asm/jump_label.h
@@ -22,7 +22,7 @@
static __always_inline bool arch_static_branch(struct static_key *key)
{
- asm goto("1:\tnop\n\t"
+ asm_volatile_goto("1:\tnop\n\t"
"nop\n\t"
".pushsection __jump_table, \"aw\"\n\t"
WORD_INSN " 1b, %l[l_yes], %0\n\t"
diff --git a/arch/mips/kernel/octeon_switch.S b/arch/mips/kernel/octeon_switch.S
index 4204d76..029e002 100644
--- a/arch/mips/kernel/octeon_switch.S
+++ b/arch/mips/kernel/octeon_switch.S
@@ -73,7 +73,7 @@
3:
#if defined(CONFIG_CC_STACKPROTECTOR) && !defined(CONFIG_SMP)
- PTR_L t8, __stack_chk_guard
+ PTR_LA t8, __stack_chk_guard
LONG_L t9, TASK_STACK_CANARY(a1)
LONG_S t9, 0(t8)
#endif
diff --git a/arch/mips/kernel/r2300_switch.S b/arch/mips/kernel/r2300_switch.S
index 38af83f..20b7b04 100644
--- a/arch/mips/kernel/r2300_switch.S
+++ b/arch/mips/kernel/r2300_switch.S
@@ -67,7 +67,7 @@
1:
#if defined(CONFIG_CC_STACKPROTECTOR) && !defined(CONFIG_SMP)
- PTR_L t8, __stack_chk_guard
+ PTR_LA t8, __stack_chk_guard
LONG_L t9, TASK_STACK_CANARY(a1)
LONG_S t9, 0(t8)
#endif
diff --git a/arch/mips/kernel/r4k_switch.S b/arch/mips/kernel/r4k_switch.S
index 921238a..078de5ea 100644
--- a/arch/mips/kernel/r4k_switch.S
+++ b/arch/mips/kernel/r4k_switch.S
@@ -69,7 +69,7 @@
1:
#if defined(CONFIG_CC_STACKPROTECTOR) && !defined(CONFIG_SMP)
- PTR_L t8, __stack_chk_guard
+ PTR_LA t8, __stack_chk_guard
LONG_L t9, TASK_STACK_CANARY(a1)
LONG_S t9, 0(t8)
#endif
diff --git a/arch/parisc/include/asm/traps.h b/arch/parisc/include/asm/traps.h
index 1945f99..4736020 100644
--- a/arch/parisc/include/asm/traps.h
+++ b/arch/parisc/include/asm/traps.h
@@ -6,7 +6,7 @@
/* traps.c */
void parisc_terminate(char *msg, struct pt_regs *regs,
- int code, unsigned long offset);
+ int code, unsigned long offset) __noreturn __cold;
/* mm/fault.c */
void do_page_fault(struct pt_regs *regs, unsigned long code,
diff --git a/arch/parisc/kernel/cache.c b/arch/parisc/kernel/cache.c
index c035673..b521c0a 100644
--- a/arch/parisc/kernel/cache.c
+++ b/arch/parisc/kernel/cache.c
@@ -602,6 +602,7 @@
__flush_cache_page(vma, vmaddr, PFN_PHYS(pfn));
}
}
+EXPORT_SYMBOL_GPL(flush_cache_page);
#ifdef CONFIG_PARISC_TMPALIAS
diff --git a/arch/parisc/kernel/smp.c b/arch/parisc/kernel/smp.c
index 8a252f2..2b96602 100644
--- a/arch/parisc/kernel/smp.c
+++ b/arch/parisc/kernel/smp.c
@@ -72,7 +72,6 @@
IPI_NOP=0,
IPI_RESCHEDULE=1,
IPI_CALL_FUNC,
- IPI_CALL_FUNC_SINGLE,
IPI_CPU_START,
IPI_CPU_STOP,
IPI_CPU_TEST
@@ -164,11 +163,6 @@
generic_smp_call_function_interrupt();
break;
- case IPI_CALL_FUNC_SINGLE:
- smp_debug(100, KERN_DEBUG "CPU%d IPI_CALL_FUNC_SINGLE\n", this_cpu);
- generic_smp_call_function_single_interrupt();
- break;
-
case IPI_CPU_START:
smp_debug(100, KERN_DEBUG "CPU%d IPI_CPU_START\n", this_cpu);
break;
@@ -260,7 +254,7 @@
void arch_send_call_function_single_ipi(int cpu)
{
- send_IPI_single(cpu, IPI_CALL_FUNC_SINGLE);
+ send_IPI_single(cpu, IPI_CALL_FUNC);
}
/*
diff --git a/arch/parisc/kernel/traps.c b/arch/parisc/kernel/traps.c
index 04e47c6..1cd1d0c 100644
--- a/arch/parisc/kernel/traps.c
+++ b/arch/parisc/kernel/traps.c
@@ -291,11 +291,6 @@
do_exit(SIGSEGV);
}
-int syscall_ipi(int (*syscall) (struct pt_regs *), struct pt_regs *regs)
-{
- return syscall(regs);
-}
-
/* gdb uses break 4,8 */
#define GDB_BREAK_INSN 0x10004
static void handle_gdb_break(struct pt_regs *regs, int wot)
@@ -805,14 +800,14 @@
else {
/*
- * The kernel should never fault on its own address space.
+ * The kernel should never fault on its own address space,
+ * unless pagefault_disable() was called before.
*/
- if (fault_space == 0)
+ if (fault_space == 0 && !in_atomic())
{
pdc_chassis_send_status(PDC_CHASSIS_DIRECT_PANIC);
parisc_terminate("Kernel Fault", regs, code, fault_address);
-
}
}
diff --git a/arch/parisc/lib/memcpy.c b/arch/parisc/lib/memcpy.c
index ac4370b..b5507ec 100644
--- a/arch/parisc/lib/memcpy.c
+++ b/arch/parisc/lib/memcpy.c
@@ -56,7 +56,7 @@
#ifdef __KERNEL__
#include <linux/module.h>
#include <linux/compiler.h>
-#include <asm/uaccess.h>
+#include <linux/uaccess.h>
#define s_space "%%sr1"
#define d_space "%%sr2"
#else
@@ -524,4 +524,17 @@
EXPORT_SYMBOL(copy_from_user);
EXPORT_SYMBOL(copy_in_user);
EXPORT_SYMBOL(memcpy);
+
+long probe_kernel_read(void *dst, const void *src, size_t size)
+{
+ unsigned long addr = (unsigned long)src;
+
+ if (size < 0 || addr < PAGE_SIZE)
+ return -EFAULT;
+
+ /* check for I/O space F_EXTEND(0xfff00000) access as well? */
+
+ return __probe_kernel_read(dst, src, size);
+}
+
#endif
diff --git a/arch/parisc/mm/fault.c b/arch/parisc/mm/fault.c
index 00c0ed3..0293588 100644
--- a/arch/parisc/mm/fault.c
+++ b/arch/parisc/mm/fault.c
@@ -171,20 +171,25 @@
unsigned long address)
{
struct vm_area_struct *vma, *prev_vma;
- struct task_struct *tsk = current;
- struct mm_struct *mm = tsk->mm;
+ struct task_struct *tsk;
+ struct mm_struct *mm;
unsigned long acc_type;
int fault;
- unsigned int flags = FAULT_FLAG_ALLOW_RETRY | FAULT_FLAG_KILLABLE;
+ unsigned int flags;
- if (in_atomic() || !mm)
+ if (in_atomic())
goto no_context;
+ tsk = current;
+ mm = tsk->mm;
+ if (!mm)
+ goto no_context;
+
+ flags = FAULT_FLAG_ALLOW_RETRY | FAULT_FLAG_KILLABLE;
if (user_mode(regs))
flags |= FAULT_FLAG_USER;
acc_type = parisc_acctyp(code, regs->iir);
-
if (acc_type & VM_WRITE)
flags |= FAULT_FLAG_WRITE;
retry:
diff --git a/arch/powerpc/include/asm/jump_label.h b/arch/powerpc/include/asm/jump_label.h
index ae098c4..f016bb6 100644
--- a/arch/powerpc/include/asm/jump_label.h
+++ b/arch/powerpc/include/asm/jump_label.h
@@ -19,7 +19,7 @@
static __always_inline bool arch_static_branch(struct static_key *key)
{
- asm goto("1:\n\t"
+ asm_volatile_goto("1:\n\t"
"nop\n\t"
".pushsection __jump_table, \"aw\"\n\t"
JUMP_ENTRY_TYPE "1b, %l[l_yes], %c0\n\t"
diff --git a/arch/powerpc/kernel/irq.c b/arch/powerpc/kernel/irq.c
index 57d286a..c7cb8c2 100644
--- a/arch/powerpc/kernel/irq.c
+++ b/arch/powerpc/kernel/irq.c
@@ -495,14 +495,15 @@
void do_IRQ(struct pt_regs *regs)
{
struct pt_regs *old_regs = set_irq_regs(regs);
- struct thread_info *curtp, *irqtp;
+ struct thread_info *curtp, *irqtp, *sirqtp;
/* Switch to the irq stack to handle this */
curtp = current_thread_info();
irqtp = hardirq_ctx[raw_smp_processor_id()];
+ sirqtp = softirq_ctx[raw_smp_processor_id()];
/* Already there ? */
- if (unlikely(curtp == irqtp)) {
+ if (unlikely(curtp == irqtp || curtp == sirqtp)) {
__do_irq(regs);
set_irq_regs(old_regs);
return;
diff --git a/arch/powerpc/kvm/book3s_hv_rmhandlers.S b/arch/powerpc/kvm/book3s_hv_rmhandlers.S
index 294b7af..c71103b 100644
--- a/arch/powerpc/kvm/book3s_hv_rmhandlers.S
+++ b/arch/powerpc/kvm/book3s_hv_rmhandlers.S
@@ -1066,7 +1066,7 @@
BEGIN_FTR_SECTION
mfspr r8, SPRN_DSCR
ld r7, HSTATE_DSCR(r13)
- std r8, VCPU_DSCR(r7)
+ std r8, VCPU_DSCR(r9)
mtspr SPRN_DSCR, r7
END_FTR_SECTION_IFSET(CPU_FTR_ARCH_206)
diff --git a/arch/powerpc/kvm/e500_mmu_host.c b/arch/powerpc/kvm/e500_mmu_host.c
index 1c6a9d72..c65593a 100644
--- a/arch/powerpc/kvm/e500_mmu_host.c
+++ b/arch/powerpc/kvm/e500_mmu_host.c
@@ -332,6 +332,13 @@
unsigned long hva;
int pfnmap = 0;
int tsize = BOOK3E_PAGESZ_4K;
+ int ret = 0;
+ unsigned long mmu_seq;
+ struct kvm *kvm = vcpu_e500->vcpu.kvm;
+
+ /* used to check for invalidations in progress */
+ mmu_seq = kvm->mmu_notifier_seq;
+ smp_rmb();
/*
* Translate guest physical to true physical, acquiring
@@ -449,6 +456,12 @@
gvaddr &= ~((tsize_pages << PAGE_SHIFT) - 1);
}
+ spin_lock(&kvm->mmu_lock);
+ if (mmu_notifier_retry(kvm, mmu_seq)) {
+ ret = -EAGAIN;
+ goto out;
+ }
+
kvmppc_e500_ref_setup(ref, gtlbe, pfn);
kvmppc_e500_setup_stlbe(&vcpu_e500->vcpu, gtlbe, tsize,
@@ -457,10 +470,13 @@
/* Clear i-cache for new pages */
kvmppc_mmu_flush_icache(pfn);
+out:
+ spin_unlock(&kvm->mmu_lock);
+
/* Drop refcount on page, so that mmu notifiers can clear it */
kvm_release_pfn_clean(pfn);
- return 0;
+ return ret;
}
/* XXX only map the one-one case, for now use TLB0 */
diff --git a/arch/s390/include/asm/jump_label.h b/arch/s390/include/asm/jump_label.h
index 6c32190..346b1c8 100644
--- a/arch/s390/include/asm/jump_label.h
+++ b/arch/s390/include/asm/jump_label.h
@@ -15,7 +15,7 @@
static __always_inline bool arch_static_branch(struct static_key *key)
{
- asm goto("0: brcl 0,0\n"
+ asm_volatile_goto("0: brcl 0,0\n"
".pushsection __jump_table, \"aw\"\n"
ASM_ALIGN "\n"
ASM_PTR " 0b, %l[label], %0\n"
diff --git a/arch/s390/kernel/crash_dump.c b/arch/s390/kernel/crash_dump.c
index c84f33d..7dd2172 100644
--- a/arch/s390/kernel/crash_dump.c
+++ b/arch/s390/kernel/crash_dump.c
@@ -40,28 +40,26 @@
}
/*
- * Copy up to one page to vmalloc or real memory
+ * Copy real to virtual or real memory
*/
-static ssize_t copy_page_real(void *buf, void *src, size_t csize)
+static int copy_from_realmem(void *dest, void *src, size_t count)
{
- size_t size;
+ unsigned long size;
+ int rc;
- if (is_vmalloc_addr(buf)) {
- BUG_ON(csize >= PAGE_SIZE);
- /* If buf is not page aligned, copy first part */
- size = min(roundup(__pa(buf), PAGE_SIZE) - __pa(buf), csize);
- if (size) {
- if (memcpy_real(load_real_addr(buf), src, size))
- return -EFAULT;
- buf += size;
- src += size;
- }
- /* Copy second part */
- size = csize - size;
- return (size) ? memcpy_real(load_real_addr(buf), src, size) : 0;
- } else {
- return memcpy_real(buf, src, csize);
- }
+ if (!count)
+ return 0;
+ if (!is_vmalloc_or_module_addr(dest))
+ return memcpy_real(dest, src, count);
+ do {
+ size = min(count, PAGE_SIZE - (__pa(dest) & ~PAGE_MASK));
+ if (memcpy_real(load_real_addr(dest), src, size))
+ return -EFAULT;
+ count -= size;
+ dest += size;
+ src += size;
+ } while (count);
+ return 0;
}
/*
@@ -114,7 +112,7 @@
rc = copy_to_user_real((void __force __user *) buf,
(void *) src, csize);
else
- rc = copy_page_real(buf, (void *) src, csize);
+ rc = copy_from_realmem(buf, (void *) src, csize);
return (rc == 0) ? rc : csize;
}
@@ -210,7 +208,7 @@
if (OLDMEM_BASE) {
if ((unsigned long) src < OLDMEM_SIZE) {
copied = min(count, OLDMEM_SIZE - (unsigned long) src);
- rc = memcpy_real(dest, src + OLDMEM_BASE, copied);
+ rc = copy_from_realmem(dest, src + OLDMEM_BASE, copied);
if (rc)
return rc;
}
@@ -223,7 +221,7 @@
return rc;
}
}
- return memcpy_real(dest + copied, src + copied, count - copied);
+ return copy_from_realmem(dest + copied, src + copied, count - copied);
}
/*
diff --git a/arch/s390/kernel/entry.S b/arch/s390/kernel/entry.S
index cc30d1f..0dc2b6d 100644
--- a/arch/s390/kernel/entry.S
+++ b/arch/s390/kernel/entry.S
@@ -266,6 +266,7 @@
tm __TI_flags+3(%r12),_TIF_SYSCALL
jno sysc_return
lm %r2,%r7,__PT_R2(%r11) # load svc arguments
+ l %r10,__TI_sysc_table(%r12) # 31 bit system call table
xr %r8,%r8 # svc 0 returns -ENOSYS
clc __PT_INT_CODE+2(2,%r11),BASED(.Lnr_syscalls+2)
jnl sysc_nr_ok # invalid svc number -> do svc 0
diff --git a/arch/s390/kernel/entry64.S b/arch/s390/kernel/entry64.S
index 2b2188b..e5b43c9 100644
--- a/arch/s390/kernel/entry64.S
+++ b/arch/s390/kernel/entry64.S
@@ -297,6 +297,7 @@
tm __TI_flags+7(%r12),_TIF_SYSCALL
jno sysc_return
lmg %r2,%r7,__PT_R2(%r11) # load svc arguments
+ lg %r10,__TI_sysc_table(%r12) # address of system call table
lghi %r8,0 # svc 0 returns -ENOSYS
llgh %r1,__PT_INT_CODE+2(%r11) # load new svc number
cghi %r1,NR_syscalls
diff --git a/arch/s390/kernel/kprobes.c b/arch/s390/kernel/kprobes.c
index 0ce9fb2..d86e64e 100644
--- a/arch/s390/kernel/kprobes.c
+++ b/arch/s390/kernel/kprobes.c
@@ -67,6 +67,11 @@
case 0xac: /* stnsm */
case 0xad: /* stosm */
return -EINVAL;
+ case 0xc6:
+ switch (insn[0] & 0x0f) {
+ case 0x00: /* exrl */
+ return -EINVAL;
+ }
}
switch (insn[0]) {
case 0x0101: /* pr */
@@ -180,7 +185,6 @@
break;
case 0xc6:
switch (insn[0] & 0x0f) {
- case 0x00: /* exrl */
case 0x02: /* pfdrl */
case 0x04: /* cghrl */
case 0x05: /* chrl */
diff --git a/arch/sparc/include/asm/jump_label.h b/arch/sparc/include/asm/jump_label.h
index 5080d16..ec2e2e2 100644
--- a/arch/sparc/include/asm/jump_label.h
+++ b/arch/sparc/include/asm/jump_label.h
@@ -9,7 +9,7 @@
static __always_inline bool arch_static_branch(struct static_key *key)
{
- asm goto("1:\n\t"
+ asm_volatile_goto("1:\n\t"
"nop\n\t"
"nop\n\t"
".pushsection __jump_table, \"aw\"\n\t"
diff --git a/arch/tile/include/asm/atomic.h b/arch/tile/include/asm/atomic.h
index d385eaa..7097984 100644
--- a/arch/tile/include/asm/atomic.h
+++ b/arch/tile/include/asm/atomic.h
@@ -166,7 +166,7 @@
*
* Atomically sets @v to @i and returns old @v
*/
-static inline u64 atomic64_xchg(atomic64_t *v, u64 n)
+static inline long long atomic64_xchg(atomic64_t *v, long long n)
{
return xchg64(&v->counter, n);
}
@@ -180,7 +180,8 @@
* Atomically checks if @v holds @o and replaces it with @n if so.
* Returns the old value at @v.
*/
-static inline u64 atomic64_cmpxchg(atomic64_t *v, u64 o, u64 n)
+static inline long long atomic64_cmpxchg(atomic64_t *v, long long o,
+ long long n)
{
return cmpxchg64(&v->counter, o, n);
}
diff --git a/arch/tile/include/asm/atomic_32.h b/arch/tile/include/asm/atomic_32.h
index 0d0395b..1ad4a1f 100644
--- a/arch/tile/include/asm/atomic_32.h
+++ b/arch/tile/include/asm/atomic_32.h
@@ -80,7 +80,7 @@
/* A 64bit atomic type */
typedef struct {
- u64 __aligned(8) counter;
+ long long counter;
} atomic64_t;
#define ATOMIC64_INIT(val) { (val) }
@@ -91,14 +91,14 @@
*
* Atomically reads the value of @v.
*/
-static inline u64 atomic64_read(const atomic64_t *v)
+static inline long long atomic64_read(const atomic64_t *v)
{
/*
* Requires an atomic op to read both 32-bit parts consistently.
* Casting away const is safe since the atomic support routines
* do not write to memory if the value has not been modified.
*/
- return _atomic64_xchg_add((u64 *)&v->counter, 0);
+ return _atomic64_xchg_add((long long *)&v->counter, 0);
}
/**
@@ -108,7 +108,7 @@
*
* Atomically adds @i to @v.
*/
-static inline void atomic64_add(u64 i, atomic64_t *v)
+static inline void atomic64_add(long long i, atomic64_t *v)
{
_atomic64_xchg_add(&v->counter, i);
}
@@ -120,7 +120,7 @@
*
* Atomically adds @i to @v and returns @i + @v
*/
-static inline u64 atomic64_add_return(u64 i, atomic64_t *v)
+static inline long long atomic64_add_return(long long i, atomic64_t *v)
{
smp_mb(); /* barrier for proper semantics */
return _atomic64_xchg_add(&v->counter, i) + i;
@@ -135,7 +135,8 @@
* Atomically adds @a to @v, so long as @v was not already @u.
* Returns non-zero if @v was not @u, and zero otherwise.
*/
-static inline u64 atomic64_add_unless(atomic64_t *v, u64 a, u64 u)
+static inline long long atomic64_add_unless(atomic64_t *v, long long a,
+ long long u)
{
smp_mb(); /* barrier for proper semantics */
return _atomic64_xchg_add_unless(&v->counter, a, u) != u;
@@ -151,7 +152,7 @@
* atomic64_set() can't be just a raw store, since it would be lost if it
* fell between the load and store of one of the other atomic ops.
*/
-static inline void atomic64_set(atomic64_t *v, u64 n)
+static inline void atomic64_set(atomic64_t *v, long long n)
{
_atomic64_xchg(&v->counter, n);
}
@@ -236,11 +237,13 @@
extern struct __get_user __atomic_or(volatile int *p, int *lock, int n);
extern struct __get_user __atomic_andn(volatile int *p, int *lock, int n);
extern struct __get_user __atomic_xor(volatile int *p, int *lock, int n);
-extern u64 __atomic64_cmpxchg(volatile u64 *p, int *lock, u64 o, u64 n);
-extern u64 __atomic64_xchg(volatile u64 *p, int *lock, u64 n);
-extern u64 __atomic64_xchg_add(volatile u64 *p, int *lock, u64 n);
-extern u64 __atomic64_xchg_add_unless(volatile u64 *p,
- int *lock, u64 o, u64 n);
+extern long long __atomic64_cmpxchg(volatile long long *p, int *lock,
+ long long o, long long n);
+extern long long __atomic64_xchg(volatile long long *p, int *lock, long long n);
+extern long long __atomic64_xchg_add(volatile long long *p, int *lock,
+ long long n);
+extern long long __atomic64_xchg_add_unless(volatile long long *p,
+ int *lock, long long o, long long n);
/* Return failure from the atomic wrappers. */
struct __get_user __atomic_bad_address(int __user *addr);
diff --git a/arch/tile/include/asm/cmpxchg.h b/arch/tile/include/asm/cmpxchg.h
index 4001d5e..0ccda3c 100644
--- a/arch/tile/include/asm/cmpxchg.h
+++ b/arch/tile/include/asm/cmpxchg.h
@@ -35,10 +35,10 @@
int _atomic_xchg_add(int *v, int i);
int _atomic_xchg_add_unless(int *v, int a, int u);
int _atomic_cmpxchg(int *ptr, int o, int n);
-u64 _atomic64_xchg(u64 *v, u64 n);
-u64 _atomic64_xchg_add(u64 *v, u64 i);
-u64 _atomic64_xchg_add_unless(u64 *v, u64 a, u64 u);
-u64 _atomic64_cmpxchg(u64 *v, u64 o, u64 n);
+long long _atomic64_xchg(long long *v, long long n);
+long long _atomic64_xchg_add(long long *v, long long i);
+long long _atomic64_xchg_add_unless(long long *v, long long a, long long u);
+long long _atomic64_cmpxchg(long long *v, long long o, long long n);
#define xchg(ptr, n) \
({ \
@@ -53,7 +53,8 @@
if (sizeof(*(ptr)) != 4) \
__cmpxchg_called_with_bad_pointer(); \
smp_mb(); \
- (typeof(*(ptr)))_atomic_cmpxchg((int *)ptr, (int)o, (int)n); \
+ (typeof(*(ptr)))_atomic_cmpxchg((int *)ptr, (int)o, \
+ (int)n); \
})
#define xchg64(ptr, n) \
@@ -61,7 +62,8 @@
if (sizeof(*(ptr)) != 8) \
__xchg_called_with_bad_pointer(); \
smp_mb(); \
- (typeof(*(ptr)))_atomic64_xchg((u64 *)(ptr), (u64)(n)); \
+ (typeof(*(ptr)))_atomic64_xchg((long long *)(ptr), \
+ (long long)(n)); \
})
#define cmpxchg64(ptr, o, n) \
@@ -69,7 +71,8 @@
if (sizeof(*(ptr)) != 8) \
__cmpxchg_called_with_bad_pointer(); \
smp_mb(); \
- (typeof(*(ptr)))_atomic64_cmpxchg((u64 *)ptr, (u64)o, (u64)n); \
+ (typeof(*(ptr)))_atomic64_cmpxchg((long long *)ptr, \
+ (long long)o, (long long)n); \
})
#else
@@ -81,10 +84,11 @@
switch (sizeof(*(ptr))) { \
case 4: \
__x = (typeof(__x))(unsigned long) \
- __insn_exch4((ptr), (u32)(unsigned long)(n)); \
+ __insn_exch4((ptr), \
+ (u32)(unsigned long)(n)); \
break; \
case 8: \
- __x = (typeof(__x)) \
+ __x = (typeof(__x)) \
__insn_exch((ptr), (unsigned long)(n)); \
break; \
default: \
@@ -103,10 +107,12 @@
switch (sizeof(*(ptr))) { \
case 4: \
__x = (typeof(__x))(unsigned long) \
- __insn_cmpexch4((ptr), (u32)(unsigned long)(n)); \
+ __insn_cmpexch4((ptr), \
+ (u32)(unsigned long)(n)); \
break; \
case 8: \
- __x = (typeof(__x))__insn_cmpexch((ptr), (u64)(n)); \
+ __x = (typeof(__x))__insn_cmpexch((ptr), \
+ (long long)(n)); \
break; \
default: \
__cmpxchg_called_with_bad_pointer(); \
diff --git a/arch/tile/include/asm/percpu.h b/arch/tile/include/asm/percpu.h
index 63294f5..4f7ae39 100644
--- a/arch/tile/include/asm/percpu.h
+++ b/arch/tile/include/asm/percpu.h
@@ -15,9 +15,37 @@
#ifndef _ASM_TILE_PERCPU_H
#define _ASM_TILE_PERCPU_H
-register unsigned long __my_cpu_offset __asm__("tp");
-#define __my_cpu_offset __my_cpu_offset
-#define set_my_cpu_offset(tp) (__my_cpu_offset = (tp))
+register unsigned long my_cpu_offset_reg asm("tp");
+
+#ifdef CONFIG_PREEMPT
+/*
+ * For full preemption, we can't just use the register variable
+ * directly, since we need barrier() to hazard against it, causing the
+ * compiler to reload anything computed from a previous "tp" value.
+ * But we also don't want to use volatile asm, since we'd like the
+ * compiler to be able to cache the value across multiple percpu reads.
+ * So we use a fake stack read as a hazard against barrier().
+ * The 'U' constraint is like 'm' but disallows postincrement.
+ */
+static inline unsigned long __my_cpu_offset(void)
+{
+ unsigned long tp;
+ register unsigned long *sp asm("sp");
+ asm("move %0, tp" : "=r" (tp) : "U" (*sp));
+ return tp;
+}
+#define __my_cpu_offset __my_cpu_offset()
+#else
+/*
+ * We don't need to hazard against barrier() since "tp" doesn't ever
+ * change with PREEMPT_NONE, and with PREEMPT_VOLUNTARY it only
+ * changes at function call points, at which we are already re-reading
+ * the value of "tp" due to "my_cpu_offset_reg" being a global variable.
+ */
+#define __my_cpu_offset my_cpu_offset_reg
+#endif
+
+#define set_my_cpu_offset(tp) (my_cpu_offset_reg = (tp))
#include <asm-generic/percpu.h>
diff --git a/arch/tile/kernel/hardwall.c b/arch/tile/kernel/hardwall.c
index df27a1f..531f4c3 100644
--- a/arch/tile/kernel/hardwall.c
+++ b/arch/tile/kernel/hardwall.c
@@ -66,7 +66,7 @@
0,
"udn",
LIST_HEAD_INIT(hardwall_types[HARDWALL_UDN].list),
- __SPIN_LOCK_INITIALIZER(hardwall_types[HARDWALL_UDN].lock),
+ __SPIN_LOCK_UNLOCKED(hardwall_types[HARDWALL_UDN].lock),
NULL
},
#ifndef __tilepro__
@@ -77,7 +77,7 @@
1, /* disabled pending hypervisor support */
"idn",
LIST_HEAD_INIT(hardwall_types[HARDWALL_IDN].list),
- __SPIN_LOCK_INITIALIZER(hardwall_types[HARDWALL_IDN].lock),
+ __SPIN_LOCK_UNLOCKED(hardwall_types[HARDWALL_IDN].lock),
NULL
},
{ /* access to user-space IPI */
@@ -87,7 +87,7 @@
0,
"ipi",
LIST_HEAD_INIT(hardwall_types[HARDWALL_IPI].list),
- __SPIN_LOCK_INITIALIZER(hardwall_types[HARDWALL_IPI].lock),
+ __SPIN_LOCK_UNLOCKED(hardwall_types[HARDWALL_IPI].lock),
NULL
},
#endif
diff --git a/arch/tile/kernel/intvec_32.S b/arch/tile/kernel/intvec_32.S
index 088d5c1..2cbe6d5 100644
--- a/arch/tile/kernel/intvec_32.S
+++ b/arch/tile/kernel/intvec_32.S
@@ -815,6 +815,9 @@
}
bzt r28, 1f
bnz r29, 1f
+ /* Disable interrupts explicitly for preemption. */
+ IRQ_DISABLE(r20,r21)
+ TRACE_IRQS_OFF
jal preempt_schedule_irq
FEEDBACK_REENTER(interrupt_return)
1:
diff --git a/arch/tile/kernel/intvec_64.S b/arch/tile/kernel/intvec_64.S
index ec755d3..b8fc497 100644
--- a/arch/tile/kernel/intvec_64.S
+++ b/arch/tile/kernel/intvec_64.S
@@ -841,6 +841,9 @@
}
beqzt r28, 1f
bnez r29, 1f
+ /* Disable interrupts explicitly for preemption. */
+ IRQ_DISABLE(r20,r21)
+ TRACE_IRQS_OFF
jal preempt_schedule_irq
FEEDBACK_REENTER(interrupt_return)
1:
diff --git a/arch/tile/kernel/stack.c b/arch/tile/kernel/stack.c
index 362284a..c93977a 100644
--- a/arch/tile/kernel/stack.c
+++ b/arch/tile/kernel/stack.c
@@ -23,6 +23,7 @@
#include <linux/mmzone.h>
#include <linux/dcache.h>
#include <linux/fs.h>
+#include <linux/string.h>
#include <asm/backtrace.h>
#include <asm/page.h>
#include <asm/ucontext.h>
@@ -332,21 +333,18 @@
}
if (vma->vm_file) {
- char *s;
p = d_path(&vma->vm_file->f_path, buf, bufsize);
if (IS_ERR(p))
p = "?";
- s = strrchr(p, '/');
- if (s)
- p = s+1;
+ name = kbasename(p);
} else {
- p = "anon";
+ name = "anon";
}
/* Generate a string description of the vma info. */
- namelen = strlen(p);
+ namelen = strlen(name);
remaining = (bufsize - 1) - namelen;
- memmove(buf, p, namelen);
+ memmove(buf, name, namelen);
snprintf(buf + namelen, remaining, "[%lx+%lx] ",
vma->vm_start, vma->vm_end - vma->vm_start);
}
diff --git a/arch/tile/lib/atomic_32.c b/arch/tile/lib/atomic_32.c
index 759efa3..c89b211 100644
--- a/arch/tile/lib/atomic_32.c
+++ b/arch/tile/lib/atomic_32.c
@@ -107,19 +107,19 @@
EXPORT_SYMBOL(_atomic_xor);
-u64 _atomic64_xchg(u64 *v, u64 n)
+long long _atomic64_xchg(long long *v, long long n)
{
return __atomic64_xchg(v, __atomic_setup(v), n);
}
EXPORT_SYMBOL(_atomic64_xchg);
-u64 _atomic64_xchg_add(u64 *v, u64 i)
+long long _atomic64_xchg_add(long long *v, long long i)
{
return __atomic64_xchg_add(v, __atomic_setup(v), i);
}
EXPORT_SYMBOL(_atomic64_xchg_add);
-u64 _atomic64_xchg_add_unless(u64 *v, u64 a, u64 u)
+long long _atomic64_xchg_add_unless(long long *v, long long a, long long u)
{
/*
* Note: argument order is switched here since it is easier
@@ -130,7 +130,7 @@
}
EXPORT_SYMBOL(_atomic64_xchg_add_unless);
-u64 _atomic64_cmpxchg(u64 *v, u64 o, u64 n)
+long long _atomic64_cmpxchg(long long *v, long long o, long long n)
{
return __atomic64_cmpxchg(v, __atomic_setup(v), o, n);
}
diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index ee2fb9d..145d703 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -860,7 +860,7 @@
config X86_UP_APIC
bool "Local APIC support on uniprocessors"
- depends on X86_32 && !SMP && !X86_32_NON_STANDARD
+ depends on X86_32 && !SMP && !X86_32_NON_STANDARD && !PCI_MSI
---help---
A local APIC (Advanced Programmable Interrupt Controller) is an
integrated interrupt controller in the CPU. If you have a single-CPU
@@ -885,11 +885,11 @@
config X86_LOCAL_APIC
def_bool y
- depends on X86_64 || SMP || X86_32_NON_STANDARD || X86_UP_APIC
+ depends on X86_64 || SMP || X86_32_NON_STANDARD || X86_UP_APIC || PCI_MSI
config X86_IO_APIC
def_bool y
- depends on X86_64 || SMP || X86_32_NON_STANDARD || X86_UP_IOAPIC
+ depends on X86_64 || SMP || X86_32_NON_STANDARD || X86_UP_IOAPIC || PCI_MSI
config X86_VISWS_APIC
def_bool y
diff --git a/arch/x86/include/asm/cpufeature.h b/arch/x86/include/asm/cpufeature.h
index d3f5c63..89270b43 100644
--- a/arch/x86/include/asm/cpufeature.h
+++ b/arch/x86/include/asm/cpufeature.h
@@ -374,7 +374,7 @@
* Catch too early usage of this before alternatives
* have run.
*/
- asm goto("1: jmp %l[t_warn]\n"
+ asm_volatile_goto("1: jmp %l[t_warn]\n"
"2:\n"
".section .altinstructions,\"a\"\n"
" .long 1b - .\n"
@@ -388,7 +388,7 @@
#endif
- asm goto("1: jmp %l[t_no]\n"
+ asm_volatile_goto("1: jmp %l[t_no]\n"
"2:\n"
".section .altinstructions,\"a\"\n"
" .long 1b - .\n"
@@ -453,7 +453,7 @@
* have. Thus, we force the jump to the widest, 4-byte, signed relative
* offset even though the last would often fit in less bytes.
*/
- asm goto("1: .byte 0xe9\n .long %l[t_dynamic] - 2f\n"
+ asm_volatile_goto("1: .byte 0xe9\n .long %l[t_dynamic] - 2f\n"
"2:\n"
".section .altinstructions,\"a\"\n"
" .long 1b - .\n" /* src offset */
diff --git a/arch/x86/include/asm/jump_label.h b/arch/x86/include/asm/jump_label.h
index 64507f3..6a2cefb 100644
--- a/arch/x86/include/asm/jump_label.h
+++ b/arch/x86/include/asm/jump_label.h
@@ -18,7 +18,7 @@
static __always_inline bool arch_static_branch(struct static_key *key)
{
- asm goto("1:"
+ asm_volatile_goto("1:"
".byte " __stringify(STATIC_KEY_INIT_NOP) "\n\t"
".pushsection __jump_table, \"aw\" \n\t"
_ASM_ALIGN "\n\t"
diff --git a/arch/x86/include/asm/mutex_64.h b/arch/x86/include/asm/mutex_64.h
index e7e6751..07537a4 100644
--- a/arch/x86/include/asm/mutex_64.h
+++ b/arch/x86/include/asm/mutex_64.h
@@ -20,7 +20,7 @@
static inline void __mutex_fastpath_lock(atomic_t *v,
void (*fail_fn)(atomic_t *))
{
- asm volatile goto(LOCK_PREFIX " decl %0\n"
+ asm_volatile_goto(LOCK_PREFIX " decl %0\n"
" jns %l[exit]\n"
: : "m" (v->counter)
: "memory", "cc"
@@ -75,7 +75,7 @@
static inline void __mutex_fastpath_unlock(atomic_t *v,
void (*fail_fn)(atomic_t *))
{
- asm volatile goto(LOCK_PREFIX " incl %0\n"
+ asm_volatile_goto(LOCK_PREFIX " incl %0\n"
" jg %l[exit]\n"
: : "m" (v->counter)
: "memory", "cc"
diff --git a/arch/x86/kernel/cpu/perf_event.c b/arch/x86/kernel/cpu/perf_event.c
index 897783b..9d84491 100644
--- a/arch/x86/kernel/cpu/perf_event.c
+++ b/arch/x86/kernel/cpu/perf_event.c
@@ -1888,10 +1888,7 @@
userpg->cap_user_rdpmc = x86_pmu.attr_rdpmc;
userpg->pmc_width = x86_pmu.cntval_bits;
- if (!boot_cpu_has(X86_FEATURE_CONSTANT_TSC))
- return;
-
- if (!boot_cpu_has(X86_FEATURE_NONSTOP_TSC))
+ if (!sched_clock_stable)
return;
userpg->cap_user_time = 1;
@@ -1899,10 +1896,8 @@
userpg->time_shift = CYC2NS_SCALE_FACTOR;
userpg->time_offset = this_cpu_read(cyc2ns_offset) - now;
- if (sched_clock_stable && !check_tsc_disabled()) {
- userpg->cap_user_time_zero = 1;
- userpg->time_zero = this_cpu_read(cyc2ns_offset);
- }
+ userpg->cap_user_time_zero = 1;
+ userpg->time_zero = this_cpu_read(cyc2ns_offset);
}
/*
diff --git a/arch/x86/kernel/reboot.c b/arch/x86/kernel/reboot.c
index e643e74..7e920bf 100644
--- a/arch/x86/kernel/reboot.c
+++ b/arch/x86/kernel/reboot.c
@@ -326,6 +326,14 @@
DMI_MATCH(DMI_PRODUCT_NAME, "Latitude E6320"),
},
},
+ { /* Handle problems with rebooting on the Latitude E5410. */
+ .callback = set_pci_reboot,
+ .ident = "Dell Latitude E5410",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "Latitude E5410"),
+ },
+ },
{ /* Handle problems with rebooting on the Latitude E5420. */
.callback = set_pci_reboot,
.ident = "Dell Latitude E5420",
diff --git a/arch/x86/kvm/vmx.c b/arch/x86/kvm/vmx.c
index 3b8e745..2b2fce1 100644
--- a/arch/x86/kvm/vmx.c
+++ b/arch/x86/kvm/vmx.c
@@ -3255,25 +3255,29 @@
static void ept_load_pdptrs(struct kvm_vcpu *vcpu)
{
+ struct kvm_mmu *mmu = vcpu->arch.walk_mmu;
+
if (!test_bit(VCPU_EXREG_PDPTR,
(unsigned long *)&vcpu->arch.regs_dirty))
return;
if (is_paging(vcpu) && is_pae(vcpu) && !is_long_mode(vcpu)) {
- vmcs_write64(GUEST_PDPTR0, vcpu->arch.mmu.pdptrs[0]);
- vmcs_write64(GUEST_PDPTR1, vcpu->arch.mmu.pdptrs[1]);
- vmcs_write64(GUEST_PDPTR2, vcpu->arch.mmu.pdptrs[2]);
- vmcs_write64(GUEST_PDPTR3, vcpu->arch.mmu.pdptrs[3]);
+ vmcs_write64(GUEST_PDPTR0, mmu->pdptrs[0]);
+ vmcs_write64(GUEST_PDPTR1, mmu->pdptrs[1]);
+ vmcs_write64(GUEST_PDPTR2, mmu->pdptrs[2]);
+ vmcs_write64(GUEST_PDPTR3, mmu->pdptrs[3]);
}
}
static void ept_save_pdptrs(struct kvm_vcpu *vcpu)
{
+ struct kvm_mmu *mmu = vcpu->arch.walk_mmu;
+
if (is_paging(vcpu) && is_pae(vcpu) && !is_long_mode(vcpu)) {
- vcpu->arch.mmu.pdptrs[0] = vmcs_read64(GUEST_PDPTR0);
- vcpu->arch.mmu.pdptrs[1] = vmcs_read64(GUEST_PDPTR1);
- vcpu->arch.mmu.pdptrs[2] = vmcs_read64(GUEST_PDPTR2);
- vcpu->arch.mmu.pdptrs[3] = vmcs_read64(GUEST_PDPTR3);
+ mmu->pdptrs[0] = vmcs_read64(GUEST_PDPTR0);
+ mmu->pdptrs[1] = vmcs_read64(GUEST_PDPTR1);
+ mmu->pdptrs[2] = vmcs_read64(GUEST_PDPTR2);
+ mmu->pdptrs[3] = vmcs_read64(GUEST_PDPTR3);
}
__set_bit(VCPU_EXREG_PDPTR,
@@ -7777,10 +7781,6 @@
vmcs_write64(GUEST_PDPTR1, vmcs12->guest_pdptr1);
vmcs_write64(GUEST_PDPTR2, vmcs12->guest_pdptr2);
vmcs_write64(GUEST_PDPTR3, vmcs12->guest_pdptr3);
- __clear_bit(VCPU_EXREG_PDPTR,
- (unsigned long *)&vcpu->arch.regs_avail);
- __clear_bit(VCPU_EXREG_PDPTR,
- (unsigned long *)&vcpu->arch.regs_dirty);
}
kvm_register_write(vcpu, VCPU_REGS_RSP, vmcs12->guest_rsp);
diff --git a/drivers/char/random.c b/drivers/char/random.c
index 7737b5b..7a744d3 100644
--- a/drivers/char/random.c
+++ b/drivers/char/random.c
@@ -640,7 +640,7 @@
*/
void add_device_randomness(const void *buf, unsigned int size)
{
- unsigned long time = get_cycles() ^ jiffies;
+ unsigned long time = random_get_entropy() ^ jiffies;
mix_pool_bytes(&input_pool, buf, size, NULL);
mix_pool_bytes(&input_pool, &time, sizeof(time), NULL);
@@ -677,7 +677,7 @@
goto out;
sample.jiffies = jiffies;
- sample.cycles = get_cycles();
+ sample.cycles = random_get_entropy();
sample.num = num;
mix_pool_bytes(&input_pool, &sample, sizeof(sample), NULL);
@@ -744,7 +744,7 @@
struct fast_pool *fast_pool = &__get_cpu_var(irq_randomness);
struct pt_regs *regs = get_irq_regs();
unsigned long now = jiffies;
- __u32 input[4], cycles = get_cycles();
+ __u32 input[4], cycles = random_get_entropy();
input[0] = cycles ^ jiffies;
input[1] = irq;
@@ -1459,12 +1459,11 @@
static u32 random_int_secret[MD5_MESSAGE_BYTES / 4] ____cacheline_aligned;
-static int __init random_int_secret_init(void)
+int random_int_secret_init(void)
{
get_random_bytes(random_int_secret, sizeof(random_int_secret));
return 0;
}
-late_initcall(random_int_secret_init);
/*
* Get a random word for internal kernel use only. Similar to urandom but
@@ -1483,7 +1482,7 @@
hash = get_cpu_var(get_random_int_hash);
- hash[0] += current->pid + jiffies + get_cycles();
+ hash[0] += current->pid + jiffies + random_get_entropy();
md5_transform(hash, random_int_secret);
ret = hash[0];
put_cpu_var(get_random_int_hash);
diff --git a/drivers/clk/samsung/Makefile b/drivers/clk/samsung/Makefile
index 3413380..8eb4799 100644
--- a/drivers/clk/samsung/Makefile
+++ b/drivers/clk/samsung/Makefile
@@ -8,6 +8,4 @@
obj-$(CONFIG_SOC_EXYNOS5420) += clk-exynos5420.o
obj-$(CONFIG_SOC_EXYNOS5440) += clk-exynos5440.o
obj-$(CONFIG_ARCH_EXYNOS) += clk-exynos-audss.o
-ifdef CONFIG_COMMON_CLK
obj-$(CONFIG_ARCH_S3C64XX) += clk-s3c64xx.o
-endif
diff --git a/drivers/clk/ux500/Makefile b/drivers/clk/ux500/Makefile
index c6a806e..521483f 100644
--- a/drivers/clk/ux500/Makefile
+++ b/drivers/clk/ux500/Makefile
@@ -8,6 +8,7 @@
obj-y += clk-sysctrl.o
# Clock definitions
+obj-y += u8500_of_clk.o
obj-y += u8500_clk.o
obj-y += u9540_clk.o
obj-y += u8540_clk.o
diff --git a/drivers/clk/ux500/u8500_of_clk.c b/drivers/clk/ux500/u8500_of_clk.c
new file mode 100644
index 0000000..cdeff29
--- /dev/null
+++ b/drivers/clk/ux500/u8500_of_clk.c
@@ -0,0 +1,559 @@
+/*
+ * Clock definitions for u8500 platform.
+ *
+ * Copyright (C) 2012 ST-Ericsson SA
+ * Author: Ulf Hansson <ulf.hansson@linaro.org>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#include <linux/of.h>
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/clk-provider.h>
+#include <linux/mfd/dbx500-prcmu.h>
+#include <linux/platform_data/clk-ux500.h>
+#include "clk.h"
+
+#define PRCC_NUM_PERIPH_CLUSTERS 6
+#define PRCC_PERIPHS_PER_CLUSTER 32
+
+static struct clk *prcmu_clk[PRCMU_NUM_CLKS];
+static struct clk *prcc_pclk[(PRCC_NUM_PERIPH_CLUSTERS + 1) * PRCC_PERIPHS_PER_CLUSTER];
+static struct clk *prcc_kclk[(PRCC_NUM_PERIPH_CLUSTERS + 1) * PRCC_PERIPHS_PER_CLUSTER];
+
+#define PRCC_SHOW(clk, base, bit) \
+ clk[(base * PRCC_PERIPHS_PER_CLUSTER) + bit]
+#define PRCC_PCLK_STORE(clk, base, bit) \
+ prcc_pclk[(base * PRCC_PERIPHS_PER_CLUSTER) + bit] = clk
+#define PRCC_KCLK_STORE(clk, base, bit) \
+ prcc_kclk[(base * PRCC_PERIPHS_PER_CLUSTER) + bit] = clk
+
+struct clk *ux500_twocell_get(struct of_phandle_args *clkspec, void *data)
+{
+ struct clk **clk_data = data;
+ unsigned int base, bit;
+
+ if (clkspec->args_count != 2)
+ return ERR_PTR(-EINVAL);
+
+ base = clkspec->args[0];
+ bit = clkspec->args[1];
+
+ if (base != 1 && base != 2 && base != 3 && base != 5 && base != 6) {
+ pr_err("%s: invalid PRCC base %d\n", __func__, base);
+ return ERR_PTR(-EINVAL);
+ }
+
+ return PRCC_SHOW(clk_data, base, bit);
+}
+
+static const struct of_device_id u8500_clk_of_match[] = {
+ { .compatible = "stericsson,u8500-clks", },
+ { },
+};
+
+void u8500_of_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base,
+ u32 clkrst5_base, u32 clkrst6_base)
+{
+ struct prcmu_fw_version *fw_version;
+ struct device_node *np = NULL;
+ struct device_node *child = NULL;
+ const char *sgaclk_parent = NULL;
+ struct clk *clk, *rtc_clk, *twd_clk;
+
+ if (of_have_populated_dt())
+ np = of_find_matching_node(NULL, u8500_clk_of_match);
+ if (!np) {
+ pr_err("Either DT or U8500 Clock node not found\n");
+ return;
+ }
+
+ /* Clock sources */
+ clk = clk_reg_prcmu_gate("soc0_pll", NULL, PRCMU_PLLSOC0,
+ CLK_IS_ROOT|CLK_IGNORE_UNUSED);
+ prcmu_clk[PRCMU_PLLSOC0] = clk;
+
+ clk = clk_reg_prcmu_gate("soc1_pll", NULL, PRCMU_PLLSOC1,
+ CLK_IS_ROOT|CLK_IGNORE_UNUSED);
+ prcmu_clk[PRCMU_PLLSOC1] = clk;
+
+ clk = clk_reg_prcmu_gate("ddr_pll", NULL, PRCMU_PLLDDR,
+ CLK_IS_ROOT|CLK_IGNORE_UNUSED);
+ prcmu_clk[PRCMU_PLLDDR] = clk;
+
+ /* FIXME: Add sys, ulp and int clocks here. */
+
+ rtc_clk = clk_register_fixed_rate(NULL, "rtc32k", "NULL",
+ CLK_IS_ROOT|CLK_IGNORE_UNUSED,
+ 32768);
+
+ /* PRCMU clocks */
+ fw_version = prcmu_get_fw_version();
+ if (fw_version != NULL) {
+ switch (fw_version->project) {
+ case PRCMU_FW_PROJECT_U8500_C2:
+ case PRCMU_FW_PROJECT_U8520:
+ case PRCMU_FW_PROJECT_U8420:
+ sgaclk_parent = "soc0_pll";
+ break;
+ default:
+ break;
+ }
+ }
+
+ if (sgaclk_parent)
+ clk = clk_reg_prcmu_gate("sgclk", sgaclk_parent,
+ PRCMU_SGACLK, 0);
+ else
+ clk = clk_reg_prcmu_gate("sgclk", NULL,
+ PRCMU_SGACLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_SGACLK] = clk;
+
+ clk = clk_reg_prcmu_gate("uartclk", NULL, PRCMU_UARTCLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_UARTCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("msp02clk", NULL, PRCMU_MSP02CLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_MSP02CLK] = clk;
+
+ clk = clk_reg_prcmu_gate("msp1clk", NULL, PRCMU_MSP1CLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_MSP1CLK] = clk;
+
+ clk = clk_reg_prcmu_gate("i2cclk", NULL, PRCMU_I2CCLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_I2CCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("slimclk", NULL, PRCMU_SLIMCLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_SLIMCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("per1clk", NULL, PRCMU_PER1CLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_PER1CLK] = clk;
+
+ clk = clk_reg_prcmu_gate("per2clk", NULL, PRCMU_PER2CLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_PER2CLK] = clk;
+
+ clk = clk_reg_prcmu_gate("per3clk", NULL, PRCMU_PER3CLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_PER3CLK] = clk;
+
+ clk = clk_reg_prcmu_gate("per5clk", NULL, PRCMU_PER5CLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_PER5CLK] = clk;
+
+ clk = clk_reg_prcmu_gate("per6clk", NULL, PRCMU_PER6CLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_PER6CLK] = clk;
+
+ clk = clk_reg_prcmu_gate("per7clk", NULL, PRCMU_PER7CLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_PER7CLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("lcdclk", NULL, PRCMU_LCDCLK, 0,
+ CLK_IS_ROOT|CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_LCDCLK] = clk;
+
+ clk = clk_reg_prcmu_opp_gate("bmlclk", NULL, PRCMU_BMLCLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_BMLCLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("hsitxclk", NULL, PRCMU_HSITXCLK, 0,
+ CLK_IS_ROOT|CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_HSITXCLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("hsirxclk", NULL, PRCMU_HSIRXCLK, 0,
+ CLK_IS_ROOT|CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_HSIRXCLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("hdmiclk", NULL, PRCMU_HDMICLK, 0,
+ CLK_IS_ROOT|CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_HDMICLK] = clk;
+
+ clk = clk_reg_prcmu_gate("apeatclk", NULL, PRCMU_APEATCLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_APEATCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("apetraceclk", NULL, PRCMU_APETRACECLK,
+ CLK_IS_ROOT);
+ prcmu_clk[PRCMU_APETRACECLK] = clk;
+
+ clk = clk_reg_prcmu_gate("mcdeclk", NULL, PRCMU_MCDECLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_MCDECLK] = clk;
+
+ clk = clk_reg_prcmu_opp_gate("ipi2cclk", NULL, PRCMU_IPI2CCLK,
+ CLK_IS_ROOT);
+ prcmu_clk[PRCMU_IPI2CCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("dsialtclk", NULL, PRCMU_DSIALTCLK,
+ CLK_IS_ROOT);
+ prcmu_clk[PRCMU_DSIALTCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("dmaclk", NULL, PRCMU_DMACLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_DMACLK] = clk;
+
+ clk = clk_reg_prcmu_gate("b2r2clk", NULL, PRCMU_B2R2CLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_B2R2CLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("tvclk", NULL, PRCMU_TVCLK, 0,
+ CLK_IS_ROOT|CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_TVCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("sspclk", NULL, PRCMU_SSPCLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_SSPCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("rngclk", NULL, PRCMU_RNGCLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_RNGCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("uiccclk", NULL, PRCMU_UICCCLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_UICCCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("timclk", NULL, PRCMU_TIMCLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_TIMCLK] = clk;
+
+ clk = clk_reg_prcmu_opp_volt_scalable("sdmmcclk", NULL, PRCMU_SDMMCCLK,
+ 100000000,
+ CLK_IS_ROOT|CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_SDMMCCLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("dsi_pll", "hdmiclk",
+ PRCMU_PLLDSI, 0, CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_PLLDSI] = clk;
+
+ clk = clk_reg_prcmu_scalable("dsi0clk", "dsi_pll",
+ PRCMU_DSI0CLK, 0, CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_DSI0CLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("dsi1clk", "dsi_pll",
+ PRCMU_DSI1CLK, 0, CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_DSI1CLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("dsi0escclk", "tvclk",
+ PRCMU_DSI0ESCCLK, 0, CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_DSI0ESCCLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("dsi1escclk", "tvclk",
+ PRCMU_DSI1ESCCLK, 0, CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_DSI1ESCCLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("dsi2escclk", "tvclk",
+ PRCMU_DSI2ESCCLK, 0, CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_DSI2ESCCLK] = clk;
+
+ clk = clk_reg_prcmu_scalable_rate("armss", NULL,
+ PRCMU_ARMSS, 0, CLK_IS_ROOT|CLK_IGNORE_UNUSED);
+ prcmu_clk[PRCMU_ARMSS] = clk;
+
+ twd_clk = clk_register_fixed_factor(NULL, "smp_twd", "armss",
+ CLK_IGNORE_UNUSED, 1, 2);
+
+ /*
+ * FIXME: Add special handled PRCMU clocks here:
+ * 1. clkout0yuv, use PRCMU as parent + need regulator + pinctrl.
+ * 2. ab9540_clkout1yuv, see clkout0yuv
+ */
+
+ /* PRCC P-clocks */
+ clk = clk_reg_prcc_pclk("p1_pclk0", "per1clk", clkrst1_base,
+ BIT(0), 0);
+ PRCC_PCLK_STORE(clk, 1, 0);
+
+ clk = clk_reg_prcc_pclk("p1_pclk1", "per1clk", clkrst1_base,
+ BIT(1), 0);
+ PRCC_PCLK_STORE(clk, 1, 1);
+
+ clk = clk_reg_prcc_pclk("p1_pclk2", "per1clk", clkrst1_base,
+ BIT(2), 0);
+ PRCC_PCLK_STORE(clk, 1, 2);
+
+ clk = clk_reg_prcc_pclk("p1_pclk3", "per1clk", clkrst1_base,
+ BIT(3), 0);
+ PRCC_PCLK_STORE(clk, 1, 3);
+
+ clk = clk_reg_prcc_pclk("p1_pclk4", "per1clk", clkrst1_base,
+ BIT(4), 0);
+ PRCC_PCLK_STORE(clk, 1, 4);
+
+ clk = clk_reg_prcc_pclk("p1_pclk5", "per1clk", clkrst1_base,
+ BIT(5), 0);
+ PRCC_PCLK_STORE(clk, 1, 5);
+
+ clk = clk_reg_prcc_pclk("p1_pclk6", "per1clk", clkrst1_base,
+ BIT(6), 0);
+ PRCC_PCLK_STORE(clk, 1, 6);
+
+ clk = clk_reg_prcc_pclk("p1_pclk7", "per1clk", clkrst1_base,
+ BIT(7), 0);
+ PRCC_PCLK_STORE(clk, 1, 7);
+
+ clk = clk_reg_prcc_pclk("p1_pclk8", "per1clk", clkrst1_base,
+ BIT(8), 0);
+ PRCC_PCLK_STORE(clk, 1, 8);
+
+ clk = clk_reg_prcc_pclk("p1_pclk9", "per1clk", clkrst1_base,
+ BIT(9), 0);
+ PRCC_PCLK_STORE(clk, 1, 9);
+
+ clk = clk_reg_prcc_pclk("p1_pclk10", "per1clk", clkrst1_base,
+ BIT(10), 0);
+ PRCC_PCLK_STORE(clk, 1, 10);
+
+ clk = clk_reg_prcc_pclk("p1_pclk11", "per1clk", clkrst1_base,
+ BIT(11), 0);
+ PRCC_PCLK_STORE(clk, 1, 11);
+
+ clk = clk_reg_prcc_pclk("p2_pclk0", "per2clk", clkrst2_base,
+ BIT(0), 0);
+ PRCC_PCLK_STORE(clk, 2, 0);
+
+ clk = clk_reg_prcc_pclk("p2_pclk1", "per2clk", clkrst2_base,
+ BIT(1), 0);
+ PRCC_PCLK_STORE(clk, 2, 1);
+
+ clk = clk_reg_prcc_pclk("p2_pclk2", "per2clk", clkrst2_base,
+ BIT(2), 0);
+ PRCC_PCLK_STORE(clk, 2, 2);
+
+ clk = clk_reg_prcc_pclk("p2_pclk3", "per2clk", clkrst2_base,
+ BIT(3), 0);
+ PRCC_PCLK_STORE(clk, 2, 3);
+
+ clk = clk_reg_prcc_pclk("p2_pclk4", "per2clk", clkrst2_base,
+ BIT(4), 0);
+ PRCC_PCLK_STORE(clk, 2, 4);
+
+ clk = clk_reg_prcc_pclk("p2_pclk5", "per2clk", clkrst2_base,
+ BIT(5), 0);
+ PRCC_PCLK_STORE(clk, 2, 5);
+
+ clk = clk_reg_prcc_pclk("p2_pclk6", "per2clk", clkrst2_base,
+ BIT(6), 0);
+ PRCC_PCLK_STORE(clk, 2, 6);
+
+ clk = clk_reg_prcc_pclk("p2_pclk7", "per2clk", clkrst2_base,
+ BIT(7), 0);
+ PRCC_PCLK_STORE(clk, 2, 7);
+
+ clk = clk_reg_prcc_pclk("p2_pclk8", "per2clk", clkrst2_base,
+ BIT(8), 0);
+ PRCC_PCLK_STORE(clk, 2, 8);
+
+ clk = clk_reg_prcc_pclk("p2_pclk9", "per2clk", clkrst2_base,
+ BIT(9), 0);
+ PRCC_PCLK_STORE(clk, 2, 9);
+
+ clk = clk_reg_prcc_pclk("p2_pclk10", "per2clk", clkrst2_base,
+ BIT(10), 0);
+ PRCC_PCLK_STORE(clk, 2, 10);
+
+ clk = clk_reg_prcc_pclk("p2_pclk11", "per2clk", clkrst2_base,
+ BIT(11), 0);
+ PRCC_PCLK_STORE(clk, 2, 11);
+
+ clk = clk_reg_prcc_pclk("p2_pclk12", "per2clk", clkrst2_base,
+ BIT(12), 0);
+ PRCC_PCLK_STORE(clk, 2, 12);
+
+ clk = clk_reg_prcc_pclk("p3_pclk0", "per3clk", clkrst3_base,
+ BIT(0), 0);
+ PRCC_PCLK_STORE(clk, 3, 0);
+
+ clk = clk_reg_prcc_pclk("p3_pclk1", "per3clk", clkrst3_base,
+ BIT(1), 0);
+ PRCC_PCLK_STORE(clk, 3, 1);
+
+ clk = clk_reg_prcc_pclk("p3_pclk2", "per3clk", clkrst3_base,
+ BIT(2), 0);
+ PRCC_PCLK_STORE(clk, 3, 2);
+
+ clk = clk_reg_prcc_pclk("p3_pclk3", "per3clk", clkrst3_base,
+ BIT(3), 0);
+ PRCC_PCLK_STORE(clk, 3, 3);
+
+ clk = clk_reg_prcc_pclk("p3_pclk4", "per3clk", clkrst3_base,
+ BIT(4), 0);
+ PRCC_PCLK_STORE(clk, 3, 4);
+
+ clk = clk_reg_prcc_pclk("p3_pclk5", "per3clk", clkrst3_base,
+ BIT(5), 0);
+ PRCC_PCLK_STORE(clk, 3, 5);
+
+ clk = clk_reg_prcc_pclk("p3_pclk6", "per3clk", clkrst3_base,
+ BIT(6), 0);
+ PRCC_PCLK_STORE(clk, 3, 6);
+
+ clk = clk_reg_prcc_pclk("p3_pclk7", "per3clk", clkrst3_base,
+ BIT(7), 0);
+ PRCC_PCLK_STORE(clk, 3, 7);
+
+ clk = clk_reg_prcc_pclk("p3_pclk8", "per3clk", clkrst3_base,
+ BIT(8), 0);
+ PRCC_PCLK_STORE(clk, 3, 8);
+
+ clk = clk_reg_prcc_pclk("p5_pclk0", "per5clk", clkrst5_base,
+ BIT(0), 0);
+ PRCC_PCLK_STORE(clk, 5, 0);
+
+ clk = clk_reg_prcc_pclk("p5_pclk1", "per5clk", clkrst5_base,
+ BIT(1), 0);
+ PRCC_PCLK_STORE(clk, 5, 1);
+
+ clk = clk_reg_prcc_pclk("p6_pclk0", "per6clk", clkrst6_base,
+ BIT(0), 0);
+ PRCC_PCLK_STORE(clk, 6, 0);
+
+ clk = clk_reg_prcc_pclk("p6_pclk1", "per6clk", clkrst6_base,
+ BIT(1), 0);
+ PRCC_PCLK_STORE(clk, 6, 1);
+
+ clk = clk_reg_prcc_pclk("p6_pclk2", "per6clk", clkrst6_base,
+ BIT(2), 0);
+ PRCC_PCLK_STORE(clk, 6, 2);
+
+ clk = clk_reg_prcc_pclk("p6_pclk3", "per6clk", clkrst6_base,
+ BIT(3), 0);
+ PRCC_PCLK_STORE(clk, 6, 3);
+
+ clk = clk_reg_prcc_pclk("p6_pclk4", "per6clk", clkrst6_base,
+ BIT(4), 0);
+ PRCC_PCLK_STORE(clk, 6, 4);
+
+ clk = clk_reg_prcc_pclk("p6_pclk5", "per6clk", clkrst6_base,
+ BIT(5), 0);
+ PRCC_PCLK_STORE(clk, 6, 5);
+
+ clk = clk_reg_prcc_pclk("p6_pclk6", "per6clk", clkrst6_base,
+ BIT(6), 0);
+ PRCC_PCLK_STORE(clk, 6, 6);
+
+ clk = clk_reg_prcc_pclk("p6_pclk7", "per6clk", clkrst6_base,
+ BIT(7), 0);
+ PRCC_PCLK_STORE(clk, 6, 7);
+
+ /* PRCC K-clocks
+ *
+ * FIXME: Some drivers requires PERPIH[n| to be automatically enabled
+ * by enabling just the K-clock, even if it is not a valid parent to
+ * the K-clock. Until drivers get fixed we might need some kind of
+ * "parent muxed join".
+ */
+
+ /* Periph1 */
+ clk = clk_reg_prcc_kclk("p1_uart0_kclk", "uartclk",
+ clkrst1_base, BIT(0), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 0);
+
+ clk = clk_reg_prcc_kclk("p1_uart1_kclk", "uartclk",
+ clkrst1_base, BIT(1), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 1);
+
+ clk = clk_reg_prcc_kclk("p1_i2c1_kclk", "i2cclk",
+ clkrst1_base, BIT(2), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 2);
+
+ clk = clk_reg_prcc_kclk("p1_msp0_kclk", "msp02clk",
+ clkrst1_base, BIT(3), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 3);
+
+ clk = clk_reg_prcc_kclk("p1_msp1_kclk", "msp1clk",
+ clkrst1_base, BIT(4), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 4);
+
+ clk = clk_reg_prcc_kclk("p1_sdi0_kclk", "sdmmcclk",
+ clkrst1_base, BIT(5), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 5);
+
+ clk = clk_reg_prcc_kclk("p1_i2c2_kclk", "i2cclk",
+ clkrst1_base, BIT(6), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 6);
+
+ clk = clk_reg_prcc_kclk("p1_slimbus0_kclk", "slimclk",
+ clkrst1_base, BIT(8), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 8);
+
+ clk = clk_reg_prcc_kclk("p1_i2c4_kclk", "i2cclk",
+ clkrst1_base, BIT(9), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 9);
+
+ clk = clk_reg_prcc_kclk("p1_msp3_kclk", "msp1clk",
+ clkrst1_base, BIT(10), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 10);
+
+ /* Periph2 */
+ clk = clk_reg_prcc_kclk("p2_i2c3_kclk", "i2cclk",
+ clkrst2_base, BIT(0), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 2, 0);
+
+ clk = clk_reg_prcc_kclk("p2_sdi4_kclk", "sdmmcclk",
+ clkrst2_base, BIT(2), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 2, 2);
+
+ clk = clk_reg_prcc_kclk("p2_msp2_kclk", "msp02clk",
+ clkrst2_base, BIT(3), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 2, 3);
+
+ clk = clk_reg_prcc_kclk("p2_sdi1_kclk", "sdmmcclk",
+ clkrst2_base, BIT(4), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 2, 4);
+
+ clk = clk_reg_prcc_kclk("p2_sdi3_kclk", "sdmmcclk",
+ clkrst2_base, BIT(5), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 2, 5);
+
+ /* Note that rate is received from parent. */
+ clk = clk_reg_prcc_kclk("p2_ssirx_kclk", "hsirxclk",
+ clkrst2_base, BIT(6),
+ CLK_SET_RATE_GATE|CLK_SET_RATE_PARENT);
+ PRCC_KCLK_STORE(clk, 2, 6);
+
+ clk = clk_reg_prcc_kclk("p2_ssitx_kclk", "hsitxclk",
+ clkrst2_base, BIT(7),
+ CLK_SET_RATE_GATE|CLK_SET_RATE_PARENT);
+ PRCC_KCLK_STORE(clk, 2, 7);
+
+ /* Periph3 */
+ clk = clk_reg_prcc_kclk("p3_ssp0_kclk", "sspclk",
+ clkrst3_base, BIT(1), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 3, 1);
+
+ clk = clk_reg_prcc_kclk("p3_ssp1_kclk", "sspclk",
+ clkrst3_base, BIT(2), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 3, 2);
+
+ clk = clk_reg_prcc_kclk("p3_i2c0_kclk", "i2cclk",
+ clkrst3_base, BIT(3), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 3, 3);
+
+ clk = clk_reg_prcc_kclk("p3_sdi2_kclk", "sdmmcclk",
+ clkrst3_base, BIT(4), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 3, 4);
+
+ clk = clk_reg_prcc_kclk("p3_ske_kclk", "rtc32k",
+ clkrst3_base, BIT(5), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 3, 5);
+
+ clk = clk_reg_prcc_kclk("p3_uart2_kclk", "uartclk",
+ clkrst3_base, BIT(6), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 3, 6);
+
+ clk = clk_reg_prcc_kclk("p3_sdi5_kclk", "sdmmcclk",
+ clkrst3_base, BIT(7), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 3, 7);
+
+ /* Periph6 */
+ clk = clk_reg_prcc_kclk("p3_rng_kclk", "rngclk",
+ clkrst6_base, BIT(0), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 6, 0);
+
+ for_each_child_of_node(np, child) {
+ static struct clk_onecell_data clk_data;
+
+ if (!of_node_cmp(child->name, "prcmu-clock")) {
+ clk_data.clks = prcmu_clk;
+ clk_data.clk_num = ARRAY_SIZE(prcmu_clk);
+ of_clk_add_provider(child, of_clk_src_onecell_get, &clk_data);
+ }
+ if (!of_node_cmp(child->name, "prcc-periph-clock"))
+ of_clk_add_provider(child, ux500_twocell_get, prcc_pclk);
+
+ if (!of_node_cmp(child->name, "prcc-kernel-clock"))
+ of_clk_add_provider(child, ux500_twocell_get, prcc_kclk);
+
+ if (!of_node_cmp(child->name, "rtc32k-clock"))
+ of_clk_add_provider(child, of_clk_src_simple_get, rtc_clk);
+
+ if (!of_node_cmp(child->name, "smp-twd-clock"))
+ of_clk_add_provider(child, of_clk_src_simple_get, twd_clk);
+ }
+}
diff --git a/drivers/clk/ux500/u8540_clk.c b/drivers/clk/ux500/u8540_clk.c
index f262588..20c8add 100644
--- a/drivers/clk/ux500/u8540_clk.c
+++ b/drivers/clk/ux500/u8540_clk.c
@@ -83,7 +83,7 @@
clk_register_clkdev(clk, NULL, "lcd");
clk_register_clkdev(clk, "lcd", "mcde");
- clk = clk_reg_prcmu_opp_gate("bmlclk", NULL, PRCMU_BML8580CLK,
+ clk = clk_reg_prcmu_opp_gate("bmlclk", NULL, PRCMU_BMLCLK,
CLK_IS_ROOT);
clk_register_clkdev(clk, NULL, "bml");
diff --git a/drivers/dma/edma.c b/drivers/dma/edma.c
index 098a8da..3519111 100644
--- a/drivers/dma/edma.c
+++ b/drivers/dma/edma.c
@@ -306,6 +306,7 @@
EDMA_SLOT_ANY);
if (echan->slot[i] < 0) {
dev_err(dev, "Failed to allocate slot\n");
+ kfree(edesc);
return NULL;
}
}
diff --git a/drivers/dma/sh/rcar-hpbdma.c b/drivers/dma/sh/rcar-hpbdma.c
index 45a5202..ebad845 100644
--- a/drivers/dma/sh/rcar-hpbdma.c
+++ b/drivers/dma/sh/rcar-hpbdma.c
@@ -93,6 +93,7 @@
void __iomem *base;
const struct hpb_dmae_slave_config *cfg;
char dev_id[16]; /* unique name per DMAC of channel */
+ dma_addr_t slave_addr;
};
struct hpb_dmae_device {
@@ -432,7 +433,6 @@
hpb_chan->xfer_mode = XFER_DOUBLE;
} else {
dev_err(hpb_chan->shdma_chan.dev, "DCR setting error");
- shdma_free_irq(&hpb_chan->shdma_chan);
return -EINVAL;
}
@@ -446,7 +446,8 @@
return 0;
}
-static int hpb_dmae_set_slave(struct shdma_chan *schan, int slave_id, bool try)
+static int hpb_dmae_set_slave(struct shdma_chan *schan, int slave_id,
+ dma_addr_t slave_addr, bool try)
{
struct hpb_dmae_chan *chan = to_chan(schan);
const struct hpb_dmae_slave_config *sc =
@@ -457,6 +458,7 @@
if (try)
return 0;
chan->cfg = sc;
+ chan->slave_addr = slave_addr ? : sc->addr;
return hpb_dmae_alloc_chan_resources(chan, sc);
}
@@ -468,7 +470,7 @@
{
struct hpb_dmae_chan *chan = to_chan(schan);
- return chan->cfg->addr;
+ return chan->slave_addr;
}
static struct shdma_desc *hpb_dmae_embedded_desc(void *buf, int i)
@@ -614,7 +616,6 @@
shdma_for_each_chan(schan, &hpbdev->shdma_dev, i) {
BUG_ON(!schan);
- shdma_free_irq(schan);
shdma_chan_remove(schan);
}
dma_dev->chancnt = 0;
diff --git a/drivers/gpio/gpio-samsung.c b/drivers/gpio/gpio-samsung.c
index 358a21c..29b5d67 100644
--- a/drivers/gpio/gpio-samsung.c
+++ b/drivers/gpio/gpio-samsung.c
@@ -2082,34 +2082,14 @@
int i, nr_chips;
int group = 0;
-#if defined(CONFIG_PINCTRL_EXYNOS) || defined(CONFIG_PINCTRL_EXYNOS5440)
/*
- * This gpio driver includes support for device tree support and there
- * are platforms using it. In order to maintain compatibility with those
- * platforms, and to allow non-dt Exynos4210 platforms to use this
- * gpiolib support, a check is added to find out if there is a active
- * pin-controller driver support available. If it is available, this
- * gpiolib support is ignored and the gpiolib support available in
- * pin-controller driver is used. This is a temporary check and will go
- * away when all of the Exynos4210 platforms have switched to using
- * device tree and the pin-ctrl driver.
- */
- struct device_node *pctrl_np;
- static const struct of_device_id exynos_pinctrl_ids[] = {
- { .compatible = "samsung,s3c2412-pinctrl", },
- { .compatible = "samsung,s3c2416-pinctrl", },
- { .compatible = "samsung,s3c2440-pinctrl", },
- { .compatible = "samsung,s3c2450-pinctrl", },
- { .compatible = "samsung,exynos4210-pinctrl", },
- { .compatible = "samsung,exynos4x12-pinctrl", },
- { .compatible = "samsung,exynos5250-pinctrl", },
- { .compatible = "samsung,exynos5440-pinctrl", },
- { }
- };
- for_each_matching_node(pctrl_np, exynos_pinctrl_ids)
- if (pctrl_np && of_device_is_available(pctrl_np))
- return -ENODEV;
-#endif
+ * Currently there are two drivers that can provide GPIO support for
+ * Samsung SoCs. For device tree enabled platforms, the new
+ * pinctrl-samsung driver is used, providing both GPIO and pin control
+ * interfaces. For legacy (non-DT) platforms this driver is used.
+ */
+ if (of_have_populated_dt())
+ return -ENODEV;
samsung_gpiolib_set_cfg(samsung_gpio_cfgs, ARRAY_SIZE(samsung_gpio_cfgs));
diff --git a/drivers/gpu/drm/drm_edid.c b/drivers/gpu/drm/drm_edid.c
index 1688ff5..830f750 100644
--- a/drivers/gpu/drm/drm_edid.c
+++ b/drivers/gpu/drm/drm_edid.c
@@ -2925,6 +2925,8 @@
/* Speaker Allocation Data Block */
if (dbl == 3) {
*sadb = kmalloc(dbl, GFP_KERNEL);
+ if (!*sadb)
+ return -ENOMEM;
memcpy(*sadb, &db[1], dbl);
count = dbl;
break;
diff --git a/drivers/gpu/drm/drm_fb_helper.c b/drivers/gpu/drm/drm_fb_helper.c
index f6f6cc7..3d13ca6e2 100644
--- a/drivers/gpu/drm/drm_fb_helper.c
+++ b/drivers/gpu/drm/drm_fb_helper.c
@@ -416,14 +416,6 @@
return;
/*
- * fbdev->blank can be called from irq context in case of a panic.
- * Since we already have our own special panic handler which will
- * restore the fbdev console mode completely, just bail out early.
- */
- if (oops_in_progress)
- return;
-
- /*
* For each CRTC in this fb, turn the connectors on/off.
*/
drm_modeset_lock_all(dev);
diff --git a/drivers/gpu/drm/gma500/gtt.c b/drivers/gpu/drm/gma500/gtt.c
index 92babac..2db731f 100644
--- a/drivers/gpu/drm/gma500/gtt.c
+++ b/drivers/gpu/drm/gma500/gtt.c
@@ -204,6 +204,7 @@
if (IS_ERR(pages))
return PTR_ERR(pages);
+ gt->npage = gt->gem.size / PAGE_SIZE;
gt->pages = pages;
return 0;
diff --git a/drivers/gpu/drm/i915/i915_dma.c b/drivers/gpu/drm/i915/i915_dma.c
index c27a210..d5c784d 100644
--- a/drivers/gpu/drm/i915/i915_dma.c
+++ b/drivers/gpu/drm/i915/i915_dma.c
@@ -1290,12 +1290,9 @@
* then we do not take part in VGA arbitration and the
* vga_client_register() fails with -ENODEV.
*/
- if (!HAS_PCH_SPLIT(dev)) {
- ret = vga_client_register(dev->pdev, dev, NULL,
- i915_vga_set_decode);
- if (ret && ret != -ENODEV)
- goto out;
- }
+ ret = vga_client_register(dev->pdev, dev, NULL, i915_vga_set_decode);
+ if (ret && ret != -ENODEV)
+ goto out;
intel_register_dsm_handler();
@@ -1351,12 +1348,6 @@
*/
intel_fbdev_initial_config(dev);
- /*
- * Must do this after fbcon init so that
- * vgacon_save_screen() works during the handover.
- */
- i915_disable_vga_mem(dev);
-
/* Only enable hotplug handling once the fbdev is fully set up. */
dev_priv->enable_hotplug_processing = true;
diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index c159e1a..38f96f6 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -3881,6 +3881,9 @@
#define GEN7_SQ_CHICKEN_MBCUNIT_CONFIG 0x9030
#define GEN7_SQ_CHICKEN_MBCUNIT_SQINTMOB (1<<11)
+#define HSW_SCRATCH1 0xb038
+#define HSW_SCRATCH1_L3_DATA_ATOMICS_DISABLE (1<<27)
+
#define HSW_FUSE_STRAP 0x42014
#define HSW_CDCLK_LIMIT (1 << 24)
@@ -4728,6 +4731,9 @@
#define GEN7_ROW_CHICKEN2_GT2 0xf4f4
#define DOP_CLOCK_GATING_DISABLE (1<<0)
+#define HSW_ROW_CHICKEN3 0xe49c
+#define HSW_ROW_CHICKEN3_L3_GLOBAL_ATOMICS_DISABLE (1 << 6)
+
#define G4X_AUD_VID_DID (dev_priv->info->display_mmio_offset + 0x62020)
#define INTEL_AUDIO_DEVCL 0x808629FB
#define INTEL_AUDIO_DEVBLC 0x80862801
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index e5822e7..581fb4b 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -3941,8 +3941,6 @@
* consider. */
void intel_connector_dpms(struct drm_connector *connector, int mode)
{
- struct intel_encoder *encoder = intel_attached_encoder(connector);
-
/* All the simple cases only support two dpms states. */
if (mode != DRM_MODE_DPMS_ON)
mode = DRM_MODE_DPMS_OFF;
@@ -3953,10 +3951,8 @@
connector->dpms = mode;
/* Only need to change hw state when actually enabled */
- if (encoder->base.crtc)
- intel_encoder_dpms(encoder, mode);
- else
- WARN_ON(encoder->connectors_active != false);
+ if (connector->encoder)
+ intel_encoder_dpms(to_intel_encoder(connector->encoder), mode);
intel_modeset_check_state(connector->dev);
}
@@ -10049,33 +10045,6 @@
POSTING_READ(vga_reg);
}
-static void i915_enable_vga_mem(struct drm_device *dev)
-{
- /* Enable VGA memory on Intel HD */
- if (HAS_PCH_SPLIT(dev)) {
- vga_get_uninterruptible(dev->pdev, VGA_RSRC_LEGACY_IO);
- outb(inb(VGA_MSR_READ) | VGA_MSR_MEM_EN, VGA_MSR_WRITE);
- vga_set_legacy_decoding(dev->pdev, VGA_RSRC_LEGACY_IO |
- VGA_RSRC_LEGACY_MEM |
- VGA_RSRC_NORMAL_IO |
- VGA_RSRC_NORMAL_MEM);
- vga_put(dev->pdev, VGA_RSRC_LEGACY_IO);
- }
-}
-
-void i915_disable_vga_mem(struct drm_device *dev)
-{
- /* Disable VGA memory on Intel HD */
- if (HAS_PCH_SPLIT(dev)) {
- vga_get_uninterruptible(dev->pdev, VGA_RSRC_LEGACY_IO);
- outb(inb(VGA_MSR_READ) & ~VGA_MSR_MEM_EN, VGA_MSR_WRITE);
- vga_set_legacy_decoding(dev->pdev, VGA_RSRC_LEGACY_IO |
- VGA_RSRC_NORMAL_IO |
- VGA_RSRC_NORMAL_MEM);
- vga_put(dev->pdev, VGA_RSRC_LEGACY_IO);
- }
-}
-
void intel_modeset_init_hw(struct drm_device *dev)
{
intel_init_power_well(dev);
@@ -10354,7 +10323,6 @@
if (I915_READ(vga_reg) != VGA_DISP_DISABLE) {
DRM_DEBUG_KMS("Something enabled VGA plane, disabling it\n");
i915_disable_vga(dev);
- i915_disable_vga_mem(dev);
}
}
@@ -10568,8 +10536,6 @@
intel_disable_fbc(dev);
- i915_enable_vga_mem(dev);
-
intel_disable_gt_powersave(dev);
ironlake_teardown_rc6(dev);
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index 79c14e2..2c555f9 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -1467,7 +1467,7 @@
/* Avoid continuous PSR exit by masking memup and hpd */
I915_WRITE(EDP_PSR_DEBUG_CTL, EDP_PSR_DEBUG_MASK_MEMUP |
- EDP_PSR_DEBUG_MASK_HPD);
+ EDP_PSR_DEBUG_MASK_HPD | EDP_PSR_DEBUG_MASK_LPSP);
intel_dp->psr_setup_done = true;
}
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
index 28cae80..9b7b68f 100644
--- a/drivers/gpu/drm/i915/intel_drv.h
+++ b/drivers/gpu/drm/i915/intel_drv.h
@@ -793,6 +793,5 @@
extern void hsw_pc8_restore_interrupts(struct drm_device *dev);
extern void intel_aux_display_runtime_get(struct drm_i915_private *dev_priv);
extern void intel_aux_display_runtime_put(struct drm_i915_private *dev_priv);
-extern void i915_disable_vga_mem(struct drm_device *dev);
#endif /* __INTEL_DRV_H__ */
diff --git a/drivers/gpu/drm/i915/intel_pm.c b/drivers/gpu/drm/i915/intel_pm.c
index dd176b7..f4c5e95 100644
--- a/drivers/gpu/drm/i915/intel_pm.c
+++ b/drivers/gpu/drm/i915/intel_pm.c
@@ -3864,8 +3864,6 @@
dev_priv->rps.rpe_delay),
dev_priv->rps.rpe_delay);
- INIT_DELAYED_WORK(&dev_priv->rps.vlv_work, vlv_rps_timer_work);
-
valleyview_set_rps(dev_priv->dev, dev_priv->rps.rpe_delay);
gen6_enable_rps_interrupts(dev);
@@ -4955,6 +4953,11 @@
I915_WRITE(GEN7_L3_CHICKEN_MODE_REGISTER,
GEN7_WA_L3_CHICKEN_MODE);
+ /* L3 caching of data atomics doesn't work -- disable it. */
+ I915_WRITE(HSW_SCRATCH1, HSW_SCRATCH1_L3_DATA_ATOMICS_DISABLE);
+ I915_WRITE(HSW_ROW_CHICKEN3,
+ _MASKED_BIT_ENABLE(HSW_ROW_CHICKEN3_L3_GLOBAL_ATOMICS_DISABLE));
+
/* This is required by WaCatErrorRejectionIssue:hsw */
I915_WRITE(GEN7_SQ_CHICKEN_MBCUNIT_CONFIG,
I915_READ(GEN7_SQ_CHICKEN_MBCUNIT_CONFIG) |
@@ -5681,5 +5684,7 @@
INIT_DELAYED_WORK(&dev_priv->rps.delayed_resume_work,
intel_gen6_powersave_work);
+
+ INIT_DELAYED_WORK(&dev_priv->rps.vlv_work, vlv_rps_timer_work);
}
diff --git a/drivers/gpu/drm/nouveau/core/subdev/mc/base.c b/drivers/gpu/drm/nouveau/core/subdev/mc/base.c
index 37712a6..e290cfa 100644
--- a/drivers/gpu/drm/nouveau/core/subdev/mc/base.c
+++ b/drivers/gpu/drm/nouveau/core/subdev/mc/base.c
@@ -113,7 +113,7 @@
pmc->use_msi = false;
break;
default:
- pmc->use_msi = nouveau_boolopt(device->cfgopt, "NvMSI", true);
+ pmc->use_msi = nouveau_boolopt(device->cfgopt, "NvMSI", false);
if (pmc->use_msi) {
pmc->use_msi = pci_enable_msi(device->pdev) == 0;
if (pmc->use_msi) {
diff --git a/drivers/gpu/drm/radeon/btc_dpm.c b/drivers/gpu/drm/radeon/btc_dpm.c
index b162e98..9b6950d 100644
--- a/drivers/gpu/drm/radeon/btc_dpm.c
+++ b/drivers/gpu/drm/radeon/btc_dpm.c
@@ -1930,7 +1930,7 @@
}
j++;
- if (j > SMC_EVERGREEN_MC_REGISTER_ARRAY_SIZE)
+ if (j >= SMC_EVERGREEN_MC_REGISTER_ARRAY_SIZE)
return -EINVAL;
tmp = RREG32(MC_PMG_CMD_MRS);
@@ -1945,7 +1945,7 @@
}
j++;
- if (j > SMC_EVERGREEN_MC_REGISTER_ARRAY_SIZE)
+ if (j >= SMC_EVERGREEN_MC_REGISTER_ARRAY_SIZE)
return -EINVAL;
break;
case MC_SEQ_RESERVE_M >> 2:
@@ -1959,7 +1959,7 @@
}
j++;
- if (j > SMC_EVERGREEN_MC_REGISTER_ARRAY_SIZE)
+ if (j >= SMC_EVERGREEN_MC_REGISTER_ARRAY_SIZE)
return -EINVAL;
break;
default:
diff --git a/drivers/gpu/drm/radeon/cik.c b/drivers/gpu/drm/radeon/cik.c
index d02fd1c..b874ccd 100644
--- a/drivers/gpu/drm/radeon/cik.c
+++ b/drivers/gpu/drm/radeon/cik.c
@@ -77,6 +77,8 @@
static void cik_program_aspm(struct radeon_device *rdev);
static void cik_init_pg(struct radeon_device *rdev);
static void cik_init_cg(struct radeon_device *rdev);
+static void cik_fini_pg(struct radeon_device *rdev);
+static void cik_fini_cg(struct radeon_device *rdev);
static void cik_enable_gui_idle_interrupt(struct radeon_device *rdev,
bool enable);
@@ -4185,6 +4187,10 @@
dev_info(rdev->dev, " VM_CONTEXT1_PROTECTION_FAULT_STATUS 0x%08X\n",
RREG32(VM_CONTEXT1_PROTECTION_FAULT_STATUS));
+ /* disable CG/PG */
+ cik_fini_pg(rdev);
+ cik_fini_cg(rdev);
+
/* stop the rlc */
cik_rlc_stop(rdev);
diff --git a/drivers/gpu/drm/radeon/evergreen.c b/drivers/gpu/drm/radeon/evergreen.c
index 555164e..b5c67a9 100644
--- a/drivers/gpu/drm/radeon/evergreen.c
+++ b/drivers/gpu/drm/radeon/evergreen.c
@@ -3131,7 +3131,7 @@
rdev->config.evergreen.sx_max_export_size = 256;
rdev->config.evergreen.sx_max_export_pos_size = 64;
rdev->config.evergreen.sx_max_export_smx_size = 192;
- rdev->config.evergreen.max_hw_contexts = 8;
+ rdev->config.evergreen.max_hw_contexts = 4;
rdev->config.evergreen.sq_num_cf_insts = 2;
rdev->config.evergreen.sc_prim_fifo_size = 0x40;
diff --git a/drivers/gpu/drm/radeon/evergreen_hdmi.c b/drivers/gpu/drm/radeon/evergreen_hdmi.c
index f71ce39..f815c20 100644
--- a/drivers/gpu/drm/radeon/evergreen_hdmi.c
+++ b/drivers/gpu/drm/radeon/evergreen_hdmi.c
@@ -288,8 +288,7 @@
/* fglrx clears sth in AFMT_AUDIO_PACKET_CONTROL2 here */
WREG32(HDMI_ACR_PACKET_CONTROL + offset,
- HDMI_ACR_AUTO_SEND | /* allow hw to sent ACR packets when required */
- HDMI_ACR_SOURCE); /* select SW CTS value */
+ HDMI_ACR_AUTO_SEND); /* allow hw to sent ACR packets when required */
evergreen_hdmi_update_ACR(encoder, mode->clock);
diff --git a/drivers/gpu/drm/radeon/evergreend.h b/drivers/gpu/drm/radeon/evergreend.h
index 8768fd6..4f6d296 100644
--- a/drivers/gpu/drm/radeon/evergreend.h
+++ b/drivers/gpu/drm/radeon/evergreend.h
@@ -1501,7 +1501,7 @@
* 6. COMMAND [29:22] | BYTE_COUNT [20:0]
*/
# define PACKET3_CP_DMA_DST_SEL(x) ((x) << 20)
- /* 0 - SRC_ADDR
+ /* 0 - DST_ADDR
* 1 - GDS
*/
# define PACKET3_CP_DMA_ENGINE(x) ((x) << 27)
@@ -1516,7 +1516,7 @@
# define PACKET3_CP_DMA_CP_SYNC (1 << 31)
/* COMMAND */
# define PACKET3_CP_DMA_DIS_WC (1 << 21)
-# define PACKET3_CP_DMA_CMD_SRC_SWAP(x) ((x) << 23)
+# define PACKET3_CP_DMA_CMD_SRC_SWAP(x) ((x) << 22)
/* 0 - none
* 1 - 8 in 16
* 2 - 8 in 32
diff --git a/drivers/gpu/drm/radeon/r600_hdmi.c b/drivers/gpu/drm/radeon/r600_hdmi.c
index b0fa600..5b72931 100644
--- a/drivers/gpu/drm/radeon/r600_hdmi.c
+++ b/drivers/gpu/drm/radeon/r600_hdmi.c
@@ -57,15 +57,15 @@
static const struct radeon_hdmi_acr r600_hdmi_predefined_acr[] = {
/* 32kHz 44.1kHz 48kHz */
/* Clock N CTS N CTS N CTS */
- { 25174, 4576, 28125, 7007, 31250, 6864, 28125 }, /* 25,20/1.001 MHz */
+ { 25175, 4576, 28125, 7007, 31250, 6864, 28125 }, /* 25,20/1.001 MHz */
{ 25200, 4096, 25200, 6272, 28000, 6144, 25200 }, /* 25.20 MHz */
{ 27000, 4096, 27000, 6272, 30000, 6144, 27000 }, /* 27.00 MHz */
{ 27027, 4096, 27027, 6272, 30030, 6144, 27027 }, /* 27.00*1.001 MHz */
{ 54000, 4096, 54000, 6272, 60000, 6144, 54000 }, /* 54.00 MHz */
{ 54054, 4096, 54054, 6272, 60060, 6144, 54054 }, /* 54.00*1.001 MHz */
- { 74175, 11648, 210937, 17836, 234375, 11648, 140625 }, /* 74.25/1.001 MHz */
+ { 74176, 11648, 210937, 17836, 234375, 11648, 140625 }, /* 74.25/1.001 MHz */
{ 74250, 4096, 74250, 6272, 82500, 6144, 74250 }, /* 74.25 MHz */
- { 148351, 11648, 421875, 8918, 234375, 5824, 140625 }, /* 148.50/1.001 MHz */
+ { 148352, 11648, 421875, 8918, 234375, 5824, 140625 }, /* 148.50/1.001 MHz */
{ 148500, 4096, 148500, 6272, 165000, 6144, 148500 }, /* 148.50 MHz */
{ 0, 4096, 0, 6272, 0, 6144, 0 } /* Other */
};
@@ -75,8 +75,15 @@
*/
static void r600_hdmi_calc_cts(uint32_t clock, int *CTS, int N, int freq)
{
- if (*CTS == 0)
- *CTS = clock * N / (128 * freq) * 1000;
+ u64 n;
+ u32 d;
+
+ if (*CTS == 0) {
+ n = (u64)clock * (u64)N * 1000ULL;
+ d = 128 * freq;
+ do_div(n, d);
+ *CTS = n;
+ }
DRM_DEBUG("Using ACR timing N=%d CTS=%d for frequency %d\n",
N, *CTS, freq);
}
@@ -444,8 +451,8 @@
}
WREG32(HDMI0_ACR_PACKET_CONTROL + offset,
- HDMI0_ACR_AUTO_SEND | /* allow hw to sent ACR packets when required */
- HDMI0_ACR_SOURCE); /* select SW CTS value */
+ HDMI0_ACR_SOURCE | /* select SW CTS value - XXX verify that hw CTS works on all families */
+ HDMI0_ACR_AUTO_SEND); /* allow hw to sent ACR packets when required */
WREG32(HDMI0_VBI_PACKET_CONTROL + offset,
HDMI0_NULL_SEND | /* send null packets when required */
diff --git a/drivers/gpu/drm/radeon/r600d.h b/drivers/gpu/drm/radeon/r600d.h
index e673fe2..7b3c7b5 100644
--- a/drivers/gpu/drm/radeon/r600d.h
+++ b/drivers/gpu/drm/radeon/r600d.h
@@ -1523,7 +1523,7 @@
*/
# define PACKET3_CP_DMA_CP_SYNC (1 << 31)
/* COMMAND */
-# define PACKET3_CP_DMA_CMD_SRC_SWAP(x) ((x) << 23)
+# define PACKET3_CP_DMA_CMD_SRC_SWAP(x) ((x) << 22)
/* 0 - none
* 1 - 8 in 16
* 2 - 8 in 32
diff --git a/drivers/gpu/drm/radeon/radeon_pm.c b/drivers/gpu/drm/radeon/radeon_pm.c
index ac07ad1..4f6b7fc 100644
--- a/drivers/gpu/drm/radeon/radeon_pm.c
+++ b/drivers/gpu/drm/radeon/radeon_pm.c
@@ -945,6 +945,8 @@
if (enable) {
mutex_lock(&rdev->pm.mutex);
rdev->pm.dpm.uvd_active = true;
+ /* disable this for now */
+#if 0
if ((rdev->pm.dpm.sd == 1) && (rdev->pm.dpm.hd == 0))
dpm_state = POWER_STATE_TYPE_INTERNAL_UVD_SD;
else if ((rdev->pm.dpm.sd == 2) && (rdev->pm.dpm.hd == 0))
@@ -954,6 +956,7 @@
else if ((rdev->pm.dpm.sd == 0) && (rdev->pm.dpm.hd == 2))
dpm_state = POWER_STATE_TYPE_INTERNAL_UVD_HD2;
else
+#endif
dpm_state = POWER_STATE_TYPE_INTERNAL_UVD;
rdev->pm.dpm.state = dpm_state;
mutex_unlock(&rdev->pm.mutex);
diff --git a/drivers/gpu/drm/radeon/radeon_test.c b/drivers/gpu/drm/radeon/radeon_test.c
index f4d6bce..12e8099 100644
--- a/drivers/gpu/drm/radeon/radeon_test.c
+++ b/drivers/gpu/drm/radeon/radeon_test.c
@@ -36,8 +36,8 @@
struct radeon_bo *vram_obj = NULL;
struct radeon_bo **gtt_obj = NULL;
uint64_t gtt_addr, vram_addr;
- unsigned i, n, size;
- int r, ring;
+ unsigned n, size;
+ int i, r, ring;
switch (flag) {
case RADEON_TEST_COPY_DMA:
diff --git a/drivers/gpu/drm/radeon/radeon_uvd.c b/drivers/gpu/drm/radeon/radeon_uvd.c
index a0f1185..4f2e73f 100644
--- a/drivers/gpu/drm/radeon/radeon_uvd.c
+++ b/drivers/gpu/drm/radeon/radeon_uvd.c
@@ -798,7 +798,8 @@
(rdev->pm.dpm.hd != hd)) {
rdev->pm.dpm.sd = sd;
rdev->pm.dpm.hd = hd;
- streams_changed = true;
+ /* disable this for now */
+ /*streams_changed = true;*/
}
}
diff --git a/drivers/gpu/drm/radeon/si.c b/drivers/gpu/drm/radeon/si.c
index c354c10..d4652af 100644
--- a/drivers/gpu/drm/radeon/si.c
+++ b/drivers/gpu/drm/radeon/si.c
@@ -85,6 +85,9 @@
uint32_t incr, uint32_t flags);
static void si_enable_gui_idle_interrupt(struct radeon_device *rdev,
bool enable);
+static void si_fini_pg(struct radeon_device *rdev);
+static void si_fini_cg(struct radeon_device *rdev);
+static void si_rlc_stop(struct radeon_device *rdev);
static const u32 verde_rlc_save_restore_register_list[] =
{
@@ -3608,6 +3611,13 @@
dev_info(rdev->dev, " VM_CONTEXT1_PROTECTION_FAULT_STATUS 0x%08X\n",
RREG32(VM_CONTEXT1_PROTECTION_FAULT_STATUS));
+ /* disable PG/CG */
+ si_fini_pg(rdev);
+ si_fini_cg(rdev);
+
+ /* stop the rlc */
+ si_rlc_stop(rdev);
+
/* Disable CP parsing/prefetching */
WREG32(CP_ME_CNTL, CP_ME_HALT | CP_PFP_HALT | CP_CE_HALT);
diff --git a/drivers/gpu/drm/radeon/si_dpm.c b/drivers/gpu/drm/radeon/si_dpm.c
index 9ace287..2332aa1 100644
--- a/drivers/gpu/drm/radeon/si_dpm.c
+++ b/drivers/gpu/drm/radeon/si_dpm.c
@@ -5208,7 +5208,7 @@
table->mc_reg_table_entry[k].mc_data[j] |= 0x100;
}
j++;
- if (j > SMC_SISLANDS_MC_REGISTER_ARRAY_SIZE)
+ if (j >= SMC_SISLANDS_MC_REGISTER_ARRAY_SIZE)
return -EINVAL;
if (!pi->mem_gddr5) {
@@ -5218,7 +5218,7 @@
table->mc_reg_table_entry[k].mc_data[j] =
(table->mc_reg_table_entry[k].mc_data[i] & 0xffff0000) >> 16;
j++;
- if (j > SMC_SISLANDS_MC_REGISTER_ARRAY_SIZE)
+ if (j >= SMC_SISLANDS_MC_REGISTER_ARRAY_SIZE)
return -EINVAL;
}
break;
@@ -5231,7 +5231,7 @@
(temp_reg & 0xffff0000) |
(table->mc_reg_table_entry[k].mc_data[i] & 0x0000ffff);
j++;
- if (j > SMC_SISLANDS_MC_REGISTER_ARRAY_SIZE)
+ if (j >= SMC_SISLANDS_MC_REGISTER_ARRAY_SIZE)
return -EINVAL;
break;
default:
diff --git a/drivers/gpu/drm/radeon/sid.h b/drivers/gpu/drm/radeon/sid.h
index 52d2ab6..7e2e0ea 100644
--- a/drivers/gpu/drm/radeon/sid.h
+++ b/drivers/gpu/drm/radeon/sid.h
@@ -1553,7 +1553,7 @@
* 6. COMMAND [30:21] | BYTE_COUNT [20:0]
*/
# define PACKET3_CP_DMA_DST_SEL(x) ((x) << 20)
- /* 0 - SRC_ADDR
+ /* 0 - DST_ADDR
* 1 - GDS
*/
# define PACKET3_CP_DMA_ENGINE(x) ((x) << 27)
@@ -1568,7 +1568,7 @@
# define PACKET3_CP_DMA_CP_SYNC (1 << 31)
/* COMMAND */
# define PACKET3_CP_DMA_DIS_WC (1 << 21)
-# define PACKET3_CP_DMA_CMD_SRC_SWAP(x) ((x) << 23)
+# define PACKET3_CP_DMA_CMD_SRC_SWAP(x) ((x) << 22)
/* 0 - none
* 1 - 8 in 16
* 2 - 8 in 32
diff --git a/drivers/gpu/drm/radeon/trinity_dpm.c b/drivers/gpu/drm/radeon/trinity_dpm.c
index 7f998bf..9364129 100644
--- a/drivers/gpu/drm/radeon/trinity_dpm.c
+++ b/drivers/gpu/drm/radeon/trinity_dpm.c
@@ -1868,7 +1868,7 @@
for (i = 0; i < SUMO_MAX_HARDWARE_POWERLEVELS; i++)
pi->at[i] = TRINITY_AT_DFLT;
- pi->enable_bapm = true;
+ pi->enable_bapm = false;
pi->enable_nbps_policy = true;
pi->enable_sclk_ds = true;
pi->enable_gfx_power_gating = true;
diff --git a/drivers/hid/Kconfig b/drivers/hid/Kconfig
index 71b70e3..c91d547 100644
--- a/drivers/hid/Kconfig
+++ b/drivers/hid/Kconfig
@@ -241,6 +241,7 @@
- Sharkoon Drakonia / Perixx MX-2000 gaming mice
- Tracer Sniper TRM-503 / NOVA Gaming Slider X200 /
Zalman ZM-GM1
+ - SHARKOON DarkGlider Gaming mouse
config HOLTEK_FF
bool "Holtek On Line Grip force feedback support"
diff --git a/drivers/hid/hid-core.c b/drivers/hid/hid-core.c
index b8470b1..5a8c011 100644
--- a/drivers/hid/hid-core.c
+++ b/drivers/hid/hid-core.c
@@ -1715,6 +1715,7 @@
{ HID_USB_DEVICE(USB_VENDOR_ID_HOLTEK_ALT, USB_DEVICE_ID_HOLTEK_ALT_KEYBOARD) },
{ HID_USB_DEVICE(USB_VENDOR_ID_HOLTEK_ALT, USB_DEVICE_ID_HOLTEK_ALT_MOUSE_A04A) },
{ HID_USB_DEVICE(USB_VENDOR_ID_HOLTEK_ALT, USB_DEVICE_ID_HOLTEK_ALT_MOUSE_A067) },
+ { HID_USB_DEVICE(USB_VENDOR_ID_HOLTEK_ALT, USB_DEVICE_ID_HOLTEK_ALT_MOUSE_A081) },
{ HID_USB_DEVICE(USB_VENDOR_ID_HUION, USB_DEVICE_ID_HUION_580) },
{ HID_USB_DEVICE(USB_VENDOR_ID_JESS2, USB_DEVICE_ID_JESS2_COLOR_RUMBLE_PAD) },
{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_ION, USB_DEVICE_ID_ICADE) },
diff --git a/drivers/hid/hid-holtek-mouse.c b/drivers/hid/hid-holtek-mouse.c
index 7e6db3c..e696566 100644
--- a/drivers/hid/hid-holtek-mouse.c
+++ b/drivers/hid/hid-holtek-mouse.c
@@ -27,6 +27,7 @@
* - USB ID 04d9:a067, sold as Sharkoon Drakonia and Perixx MX-2000
* - USB ID 04d9:a04a, sold as Tracer Sniper TRM-503, NOVA Gaming Slider X200
* and Zalman ZM-GM1
+ * - USB ID 04d9:a081, sold as SHARKOON DarkGlider Gaming mouse
*/
static __u8 *holtek_mouse_report_fixup(struct hid_device *hdev, __u8 *rdesc,
@@ -46,6 +47,7 @@
}
break;
case USB_DEVICE_ID_HOLTEK_ALT_MOUSE_A04A:
+ case USB_DEVICE_ID_HOLTEK_ALT_MOUSE_A081:
if (*rsize >= 113 && rdesc[106] == 0xff && rdesc[107] == 0x7f
&& rdesc[111] == 0xff && rdesc[112] == 0x7f) {
hid_info(hdev, "Fixing up report descriptor\n");
@@ -63,6 +65,8 @@
USB_DEVICE_ID_HOLTEK_ALT_MOUSE_A067) },
{ HID_USB_DEVICE(USB_VENDOR_ID_HOLTEK_ALT,
USB_DEVICE_ID_HOLTEK_ALT_MOUSE_A04A) },
+ { HID_USB_DEVICE(USB_VENDOR_ID_HOLTEK_ALT,
+ USB_DEVICE_ID_HOLTEK_ALT_MOUSE_A081) },
{ }
};
MODULE_DEVICE_TABLE(hid, holtek_mouse_devices);
diff --git a/drivers/hid/hid-ids.h b/drivers/hid/hid-ids.h
index e60e8d5..9cbc7ab 100644
--- a/drivers/hid/hid-ids.h
+++ b/drivers/hid/hid-ids.h
@@ -450,6 +450,7 @@
#define USB_DEVICE_ID_HOLTEK_ALT_KEYBOARD 0xa055
#define USB_DEVICE_ID_HOLTEK_ALT_MOUSE_A067 0xa067
#define USB_DEVICE_ID_HOLTEK_ALT_MOUSE_A04A 0xa04a
+#define USB_DEVICE_ID_HOLTEK_ALT_MOUSE_A081 0xa081
#define USB_VENDOR_ID_IMATION 0x0718
#define USB_DEVICE_ID_DISC_STAKKA 0xd000
diff --git a/drivers/hid/hid-roccat-kone.c b/drivers/hid/hid-roccat-kone.c
index 602c188..6101816 100644
--- a/drivers/hid/hid-roccat-kone.c
+++ b/drivers/hid/hid-roccat-kone.c
@@ -382,7 +382,7 @@
}
#define PROFILE_ATTR(number) \
static struct bin_attribute bin_attr_profile##number = { \
- .attr = { .name = "profile##number", .mode = 0660 }, \
+ .attr = { .name = "profile" #number, .mode = 0660 }, \
.size = sizeof(struct kone_profile), \
.read = kone_sysfs_read_profilex, \
.write = kone_sysfs_write_profilex, \
diff --git a/drivers/hid/hid-roccat-koneplus.c b/drivers/hid/hid-roccat-koneplus.c
index 5ddf605..5e99fcd 100644
--- a/drivers/hid/hid-roccat-koneplus.c
+++ b/drivers/hid/hid-roccat-koneplus.c
@@ -229,13 +229,13 @@
#define PROFILE_ATTR(number) \
static struct bin_attribute bin_attr_profile##number##_settings = { \
- .attr = { .name = "profile##number##_settings", .mode = 0440 }, \
+ .attr = { .name = "profile" #number "_settings", .mode = 0440 }, \
.size = KONEPLUS_SIZE_PROFILE_SETTINGS, \
.read = koneplus_sysfs_read_profilex_settings, \
.private = &profile_numbers[number-1], \
}; \
static struct bin_attribute bin_attr_profile##number##_buttons = { \
- .attr = { .name = "profile##number##_buttons", .mode = 0440 }, \
+ .attr = { .name = "profile" #number "_buttons", .mode = 0440 }, \
.size = KONEPLUS_SIZE_PROFILE_BUTTONS, \
.read = koneplus_sysfs_read_profilex_buttons, \
.private = &profile_numbers[number-1], \
diff --git a/drivers/hid/hid-roccat-kovaplus.c b/drivers/hid/hid-roccat-kovaplus.c
index 515bc03..0c8e1ef 100644
--- a/drivers/hid/hid-roccat-kovaplus.c
+++ b/drivers/hid/hid-roccat-kovaplus.c
@@ -257,13 +257,13 @@
#define PROFILE_ATTR(number) \
static struct bin_attribute bin_attr_profile##number##_settings = { \
- .attr = { .name = "profile##number##_settings", .mode = 0440 }, \
+ .attr = { .name = "profile" #number "_settings", .mode = 0440 }, \
.size = KOVAPLUS_SIZE_PROFILE_SETTINGS, \
.read = kovaplus_sysfs_read_profilex_settings, \
.private = &profile_numbers[number-1], \
}; \
static struct bin_attribute bin_attr_profile##number##_buttons = { \
- .attr = { .name = "profile##number##_buttons", .mode = 0440 }, \
+ .attr = { .name = "profile" #number "_buttons", .mode = 0440 }, \
.size = KOVAPLUS_SIZE_PROFILE_BUTTONS, \
.read = kovaplus_sysfs_read_profilex_buttons, \
.private = &profile_numbers[number-1], \
diff --git a/drivers/hid/hid-roccat-pyra.c b/drivers/hid/hid-roccat-pyra.c
index 5a6dbbe..1a07e07 100644
--- a/drivers/hid/hid-roccat-pyra.c
+++ b/drivers/hid/hid-roccat-pyra.c
@@ -225,13 +225,13 @@
#define PROFILE_ATTR(number) \
static struct bin_attribute bin_attr_profile##number##_settings = { \
- .attr = { .name = "profile##number##_settings", .mode = 0440 }, \
+ .attr = { .name = "profile" #number "_settings", .mode = 0440 }, \
.size = PYRA_SIZE_PROFILE_SETTINGS, \
.read = pyra_sysfs_read_profilex_settings, \
.private = &profile_numbers[number-1], \
}; \
static struct bin_attribute bin_attr_profile##number##_buttons = { \
- .attr = { .name = "profile##number##_buttons", .mode = 0440 }, \
+ .attr = { .name = "profile" #number "_buttons", .mode = 0440 }, \
.size = PYRA_SIZE_PROFILE_BUTTONS, \
.read = pyra_sysfs_read_profilex_buttons, \
.private = &profile_numbers[number-1], \
diff --git a/drivers/hid/hid-wiimote-modules.c b/drivers/hid/hid-wiimote-modules.c
index 2e7d644..71adf9e 100644
--- a/drivers/hid/hid-wiimote-modules.c
+++ b/drivers/hid/hid-wiimote-modules.c
@@ -119,12 +119,22 @@
* the rumble motor, this flag shouldn't be set.
*/
+/* used by wiimod_rumble and wiipro_rumble */
+static void wiimod_rumble_worker(struct work_struct *work)
+{
+ struct wiimote_data *wdata = container_of(work, struct wiimote_data,
+ rumble_worker);
+
+ spin_lock_irq(&wdata->state.lock);
+ wiiproto_req_rumble(wdata, wdata->state.cache_rumble);
+ spin_unlock_irq(&wdata->state.lock);
+}
+
static int wiimod_rumble_play(struct input_dev *dev, void *data,
struct ff_effect *eff)
{
struct wiimote_data *wdata = input_get_drvdata(dev);
__u8 value;
- unsigned long flags;
/*
* The wiimote supports only a single rumble motor so if any magnitude
@@ -137,9 +147,10 @@
else
value = 0;
- spin_lock_irqsave(&wdata->state.lock, flags);
- wiiproto_req_rumble(wdata, value);
- spin_unlock_irqrestore(&wdata->state.lock, flags);
+ /* Locking state.lock here might deadlock with input_event() calls.
+ * schedule_work acts as barrier. Merging multiple changes is fine. */
+ wdata->state.cache_rumble = value;
+ schedule_work(&wdata->rumble_worker);
return 0;
}
@@ -147,6 +158,8 @@
static int wiimod_rumble_probe(const struct wiimod_ops *ops,
struct wiimote_data *wdata)
{
+ INIT_WORK(&wdata->rumble_worker, wiimod_rumble_worker);
+
set_bit(FF_RUMBLE, wdata->input->ffbit);
if (input_ff_create_memless(wdata->input, NULL, wiimod_rumble_play))
return -ENOMEM;
@@ -159,6 +172,8 @@
{
unsigned long flags;
+ cancel_work_sync(&wdata->rumble_worker);
+
spin_lock_irqsave(&wdata->state.lock, flags);
wiiproto_req_rumble(wdata, 0);
spin_unlock_irqrestore(&wdata->state.lock, flags);
@@ -1731,7 +1746,6 @@
{
struct wiimote_data *wdata = input_get_drvdata(dev);
__u8 value;
- unsigned long flags;
/*
* The wiimote supports only a single rumble motor so if any magnitude
@@ -1744,9 +1758,10 @@
else
value = 0;
- spin_lock_irqsave(&wdata->state.lock, flags);
- wiiproto_req_rumble(wdata, value);
- spin_unlock_irqrestore(&wdata->state.lock, flags);
+ /* Locking state.lock here might deadlock with input_event() calls.
+ * schedule_work acts as barrier. Merging multiple changes is fine. */
+ wdata->state.cache_rumble = value;
+ schedule_work(&wdata->rumble_worker);
return 0;
}
@@ -1756,6 +1771,8 @@
{
int ret, i;
+ INIT_WORK(&wdata->rumble_worker, wiimod_rumble_worker);
+
wdata->extension.input = input_allocate_device();
if (!wdata->extension.input)
return -ENOMEM;
@@ -1817,12 +1834,13 @@
if (!wdata->extension.input)
return;
+ input_unregister_device(wdata->extension.input);
+ wdata->extension.input = NULL;
+ cancel_work_sync(&wdata->rumble_worker);
+
spin_lock_irqsave(&wdata->state.lock, flags);
wiiproto_req_rumble(wdata, 0);
spin_unlock_irqrestore(&wdata->state.lock, flags);
-
- input_unregister_device(wdata->extension.input);
- wdata->extension.input = NULL;
}
static const struct wiimod_ops wiimod_pro = {
diff --git a/drivers/hid/hid-wiimote.h b/drivers/hid/hid-wiimote.h
index f1474f3..75db0c4 100644
--- a/drivers/hid/hid-wiimote.h
+++ b/drivers/hid/hid-wiimote.h
@@ -133,13 +133,15 @@
__u8 *cmd_read_buf;
__u8 cmd_read_size;
- /* calibration data */
+ /* calibration/cache data */
__u16 calib_bboard[4][3];
+ __u8 cache_rumble;
};
struct wiimote_data {
struct hid_device *hdev;
struct input_dev *input;
+ struct work_struct rumble_worker;
struct led_classdev *leds[4];
struct input_dev *accel;
struct input_dev *ir;
diff --git a/drivers/hid/hidraw.c b/drivers/hid/hidraw.c
index 8918dd1..6a6dd5c 100644
--- a/drivers/hid/hidraw.c
+++ b/drivers/hid/hidraw.c
@@ -308,18 +308,25 @@
static void drop_ref(struct hidraw *hidraw, int exists_bit)
{
if (exists_bit) {
- hid_hw_close(hidraw->hid);
hidraw->exist = 0;
- if (hidraw->open)
+ if (hidraw->open) {
+ hid_hw_close(hidraw->hid);
wake_up_interruptible(&hidraw->wait);
+ }
} else {
--hidraw->open;
}
-
- if (!hidraw->open && !hidraw->exist) {
- device_destroy(hidraw_class, MKDEV(hidraw_major, hidraw->minor));
- hidraw_table[hidraw->minor] = NULL;
- kfree(hidraw);
+ if (!hidraw->open) {
+ if (!hidraw->exist) {
+ device_destroy(hidraw_class,
+ MKDEV(hidraw_major, hidraw->minor));
+ hidraw_table[hidraw->minor] = NULL;
+ kfree(hidraw);
+ } else {
+ /* close device for last reader */
+ hid_hw_power(hidraw->hid, PM_HINT_NORMAL);
+ hid_hw_close(hidraw->hid);
+ }
}
}
diff --git a/drivers/hid/uhid.c b/drivers/hid/uhid.c
index 5bf2fb7..93b00d7 100644
--- a/drivers/hid/uhid.c
+++ b/drivers/hid/uhid.c
@@ -615,7 +615,7 @@
static struct miscdevice uhid_misc = {
.fops = &uhid_fops,
- .minor = MISC_DYNAMIC_MINOR,
+ .minor = UHID_MINOR,
.name = UHID_NAME,
};
@@ -634,4 +634,5 @@
MODULE_LICENSE("GPL");
MODULE_AUTHOR("David Herrmann <dh.herrmann@gmail.com>");
MODULE_DESCRIPTION("User-space I/O driver support for HID subsystem");
+MODULE_ALIAS_MISCDEV(UHID_MINOR);
MODULE_ALIAS("devname:" UHID_NAME);
diff --git a/drivers/hwmon/applesmc.c b/drivers/hwmon/applesmc.c
index 98814d1..3288f13 100644
--- a/drivers/hwmon/applesmc.c
+++ b/drivers/hwmon/applesmc.c
@@ -230,6 +230,7 @@
static int read_smc(u8 cmd, const char *key, u8 *buffer, u8 len)
{
+ u8 status, data = 0;
int i;
if (send_command(cmd) || send_argument(key)) {
@@ -237,6 +238,7 @@
return -EIO;
}
+ /* This has no effect on newer (2012) SMCs */
if (send_byte(len, APPLESMC_DATA_PORT)) {
pr_warn("%.4s: read len fail\n", key);
return -EIO;
@@ -250,6 +252,17 @@
buffer[i] = inb(APPLESMC_DATA_PORT);
}
+ /* Read the data port until bit0 is cleared */
+ for (i = 0; i < 16; i++) {
+ udelay(APPLESMC_MIN_WAIT);
+ status = inb(APPLESMC_CMD_PORT);
+ if (!(status & 0x01))
+ break;
+ data = inb(APPLESMC_DATA_PORT);
+ }
+ if (i)
+ pr_warn("flushed %d bytes, last value is: %d\n", i, data);
+
return 0;
}
diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c
index 4c1b605..0aa0113 100644
--- a/drivers/i2c/busses/i2c-designware-platdrv.c
+++ b/drivers/i2c/busses/i2c-designware-platdrv.c
@@ -270,7 +270,8 @@
MODULE_ALIAS("platform:i2c_designware");
static struct platform_driver dw_i2c_driver = {
- .remove = dw_i2c_remove,
+ .probe = dw_i2c_probe,
+ .remove = dw_i2c_remove,
.driver = {
.name = "i2c_designware",
.owner = THIS_MODULE,
@@ -282,7 +283,7 @@
static int __init dw_i2c_init_driver(void)
{
- return platform_driver_probe(&dw_i2c_driver, dw_i2c_probe);
+ return platform_driver_register(&dw_i2c_driver);
}
subsys_initcall(dw_i2c_init_driver);
diff --git a/drivers/i2c/busses/i2c-imx.c b/drivers/i2c/busses/i2c-imx.c
index ccf4665..1d7efa3 100644
--- a/drivers/i2c/busses/i2c-imx.c
+++ b/drivers/i2c/busses/i2c-imx.c
@@ -365,7 +365,7 @@
clk_disable_unprepare(i2c_imx->clk);
}
-static void __init i2c_imx_set_clk(struct imx_i2c_struct *i2c_imx,
+static void i2c_imx_set_clk(struct imx_i2c_struct *i2c_imx,
unsigned int rate)
{
struct imx_i2c_clk_pair *i2c_clk_div = i2c_imx->hwdata->clk_div;
@@ -589,7 +589,7 @@
.functionality = i2c_imx_func,
};
-static int __init i2c_imx_probe(struct platform_device *pdev)
+static int i2c_imx_probe(struct platform_device *pdev)
{
const struct of_device_id *of_id = of_match_device(i2c_imx_dt_ids,
&pdev->dev);
@@ -697,7 +697,7 @@
return 0; /* Return OK */
}
-static int __exit i2c_imx_remove(struct platform_device *pdev)
+static int i2c_imx_remove(struct platform_device *pdev)
{
struct imx_i2c_struct *i2c_imx = platform_get_drvdata(pdev);
@@ -715,7 +715,8 @@
}
static struct platform_driver i2c_imx_driver = {
- .remove = __exit_p(i2c_imx_remove),
+ .probe = i2c_imx_probe,
+ .remove = i2c_imx_remove,
.driver = {
.name = DRIVER_NAME,
.owner = THIS_MODULE,
@@ -726,7 +727,7 @@
static int __init i2c_adap_imx_init(void)
{
- return platform_driver_probe(&i2c_imx_driver, i2c_imx_probe);
+ return platform_driver_register(&i2c_imx_driver);
}
subsys_initcall(i2c_adap_imx_init);
diff --git a/drivers/i2c/busses/i2c-mxs.c b/drivers/i2c/busses/i2c-mxs.c
index f4a0167..b7c8577 100644
--- a/drivers/i2c/busses/i2c-mxs.c
+++ b/drivers/i2c/busses/i2c-mxs.c
@@ -780,12 +780,13 @@
.owner = THIS_MODULE,
.of_match_table = mxs_i2c_dt_ids,
},
+ .probe = mxs_i2c_probe,
.remove = mxs_i2c_remove,
};
static int __init mxs_i2c_init(void)
{
- return platform_driver_probe(&mxs_i2c_driver, mxs_i2c_probe);
+ return platform_driver_register(&mxs_i2c_driver);
}
subsys_initcall(mxs_i2c_init);
diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 6d8308d..9967a6f 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -939,6 +939,9 @@
/*
* ProDB0017052: Clear ARDY bit twice
*/
+ if (stat & OMAP_I2C_STAT_ARDY)
+ omap_i2c_ack_stat(dev, OMAP_I2C_STAT_ARDY);
+
if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK |
OMAP_I2C_STAT_AL)) {
omap_i2c_ack_stat(dev, (OMAP_I2C_STAT_RRDY |
diff --git a/drivers/i2c/busses/i2c-stu300.c b/drivers/i2c/busses/i2c-stu300.c
index f8f6f2e..04a17b9 100644
--- a/drivers/i2c/busses/i2c-stu300.c
+++ b/drivers/i2c/busses/i2c-stu300.c
@@ -859,8 +859,7 @@
.functionality = stu300_func,
};
-static int __init
-stu300_probe(struct platform_device *pdev)
+static int stu300_probe(struct platform_device *pdev)
{
struct stu300_dev *dev;
struct i2c_adapter *adap;
@@ -966,8 +965,7 @@
#define STU300_I2C_PM NULL
#endif
-static int __exit
-stu300_remove(struct platform_device *pdev)
+static int stu300_remove(struct platform_device *pdev)
{
struct stu300_dev *dev = platform_get_drvdata(pdev);
@@ -989,13 +987,14 @@
.pm = STU300_I2C_PM,
.of_match_table = stu300_dt_match,
},
- .remove = __exit_p(stu300_remove),
+ .probe = stu300_probe,
+ .remove = stu300_remove,
};
static int __init stu300_init(void)
{
- return platform_driver_probe(&stu300_i2c_driver, stu300_probe);
+ return platform_driver_register(&stu300_i2c_driver);
}
static void __exit stu300_exit(void)
diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c
index 29d3f04..3be58f8 100644
--- a/drivers/i2c/i2c-core.c
+++ b/drivers/i2c/i2c-core.c
@@ -1134,6 +1134,9 @@
acpi_handle handle;
acpi_status status;
+ if (!adap->dev.parent)
+ return;
+
handle = ACPI_HANDLE(adap->dev.parent);
if (!handle)
return;
diff --git a/drivers/i2c/muxes/i2c-arb-gpio-challenge.c b/drivers/i2c/muxes/i2c-arb-gpio-challenge.c
index 74b41ae..928656e 100644
--- a/drivers/i2c/muxes/i2c-arb-gpio-challenge.c
+++ b/drivers/i2c/muxes/i2c-arb-gpio-challenge.c
@@ -200,7 +200,7 @@
arb->parent = of_find_i2c_adapter_by_node(parent_np);
if (!arb->parent) {
dev_err(dev, "Cannot find parent bus\n");
- return -EINVAL;
+ return -EPROBE_DEFER;
}
/* Actually add the mux adapter */
diff --git a/drivers/i2c/muxes/i2c-mux-gpio.c b/drivers/i2c/muxes/i2c-mux-gpio.c
index 5d4a99b..a764da7 100644
--- a/drivers/i2c/muxes/i2c-mux-gpio.c
+++ b/drivers/i2c/muxes/i2c-mux-gpio.c
@@ -66,7 +66,7 @@
struct device_node *adapter_np, *child;
struct i2c_adapter *adapter;
unsigned *values, *gpios;
- int i = 0;
+ int i = 0, ret;
if (!np)
return -ENODEV;
@@ -79,7 +79,7 @@
adapter = of_find_i2c_adapter_by_node(adapter_np);
if (!adapter) {
dev_err(&pdev->dev, "Cannot find parent bus\n");
- return -ENODEV;
+ return -EPROBE_DEFER;
}
mux->data.parent = i2c_adapter_id(adapter);
put_device(&adapter->dev);
@@ -116,8 +116,12 @@
return -ENOMEM;
}
- for (i = 0; i < mux->data.n_gpios; i++)
- gpios[i] = of_get_named_gpio(np, "mux-gpios", i);
+ for (i = 0; i < mux->data.n_gpios; i++) {
+ ret = of_get_named_gpio(np, "mux-gpios", i);
+ if (ret < 0)
+ return ret;
+ gpios[i] = ret;
+ }
mux->data.gpios = gpios;
@@ -177,7 +181,7 @@
if (!parent) {
dev_err(&pdev->dev, "Parent adapter (%d) not found\n",
mux->data.parent);
- return -ENODEV;
+ return -EPROBE_DEFER;
}
mux->parent = parent;
diff --git a/drivers/i2c/muxes/i2c-mux-pinctrl.c b/drivers/i2c/muxes/i2c-mux-pinctrl.c
index 69a9173..68a3715 100644
--- a/drivers/i2c/muxes/i2c-mux-pinctrl.c
+++ b/drivers/i2c/muxes/i2c-mux-pinctrl.c
@@ -113,7 +113,7 @@
adapter = of_find_i2c_adapter_by_node(adapter_np);
if (!adapter) {
dev_err(mux->dev, "Cannot find parent bus\n");
- return -ENODEV;
+ return -EPROBE_DEFER;
}
mux->pdata->parent_bus_num = i2c_adapter_id(adapter);
put_device(&adapter->dev);
@@ -211,7 +211,7 @@
if (!mux->parent) {
dev_err(&pdev->dev, "Parent adapter (%d) not found\n",
mux->pdata->parent_bus_num);
- ret = -ENODEV;
+ ret = -EPROBE_DEFER;
goto err;
}
diff --git a/drivers/iommu/Kconfig b/drivers/iommu/Kconfig
index fe302e3..c880eba 100644
--- a/drivers/iommu/Kconfig
+++ b/drivers/iommu/Kconfig
@@ -52,7 +52,7 @@
select PCI_PRI
select PCI_PASID
select IOMMU_API
- depends on X86_64 && PCI && ACPI && X86_IO_APIC
+ depends on X86_64 && PCI && ACPI
---help---
With this option you can enable support for AMD IOMMU hardware in
your system. An IOMMU is a hardware component which provides
diff --git a/drivers/irqchip/irq-vic.c b/drivers/irqchip/irq-vic.c
index 2bbb004..8e21ae0 100644
--- a/drivers/irqchip/irq-vic.c
+++ b/drivers/irqchip/irq-vic.c
@@ -469,6 +469,8 @@
int __init vic_of_init(struct device_node *node, struct device_node *parent)
{
void __iomem *regs;
+ u32 interrupt_mask = ~0;
+ u32 wakeup_mask = ~0;
if (WARN(parent, "non-root VICs are not supported"))
return -EINVAL;
@@ -477,10 +479,13 @@
if (WARN_ON(!regs))
return -EIO;
+ of_property_read_u32(node, "valid-mask", &interrupt_mask);
+ of_property_read_u32(node, "valid-wakeup-mask", &wakeup_mask);
+
/*
* Passing 0 as first IRQ makes the simple domain allocate descriptors
*/
- __vic_init(regs, 0, ~0, ~0, node);
+ __vic_init(regs, 0, interrupt_mask, wakeup_mask, node);
return 0;
}
diff --git a/drivers/md/bcache/request.c b/drivers/md/bcache/request.c
index 71eb233..b6a74bc 100644
--- a/drivers/md/bcache/request.c
+++ b/drivers/md/bcache/request.c
@@ -996,6 +996,7 @@
closure_bio_submit(bio, cl, s->d);
} else {
bch_writeback_add(dc);
+ s->op.cache_bio = bio;
if (bio->bi_rw & REQ_FLUSH) {
/* Also need to send a flush to the backing device */
@@ -1008,8 +1009,6 @@
flush->bi_private = cl;
closure_bio_submit(flush, cl, s->d);
- } else {
- s->op.cache_bio = bio;
}
}
out:
diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c
index 53f371d..b9ce60c 100644
--- a/drivers/mfd/db8500-prcmu.c
+++ b/drivers/mfd/db8500-prcmu.c
@@ -480,7 +480,6 @@
CLK_MGT_ENTRY(PER6CLK, PLL_DIV, true),
CLK_MGT_ENTRY(PER7CLK, PLL_DIV, true),
CLK_MGT_ENTRY(LCDCLK, PLL_FIX, true),
- CLK_MGT_ENTRY(BML8580CLK, PLL_DIV, true),
CLK_MGT_ENTRY(BMLCLK, PLL_DIV, true),
CLK_MGT_ENTRY(HSITXCLK, PLL_DIV, true),
CLK_MGT_ENTRY(HSIRXCLK, PLL_DIV, true),
diff --git a/drivers/mfd/dbx500-prcmu-regs.h b/drivers/mfd/dbx500-prcmu-regs.h
index 4f6f0fa..7cc32a8 100644
--- a/drivers/mfd/dbx500-prcmu-regs.h
+++ b/drivers/mfd/dbx500-prcmu-regs.h
@@ -32,7 +32,6 @@
#define PRCM_PER7CLK_MGT (0x040)
#define PRCM_LCDCLK_MGT (0x044)
#define PRCM_BMLCLK_MGT (0x04C)
-#define PRCM_BML8580CLK_MGT (0x108)
#define PRCM_HSITXCLK_MGT (0x050)
#define PRCM_HSIRXCLK_MGT (0x054)
#define PRCM_HDMICLK_MGT (0x058)
diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c
index 26b14f9..6bc9618 100644
--- a/drivers/mtd/devices/m25p80.c
+++ b/drivers/mtd/devices/m25p80.c
@@ -168,12 +168,25 @@
*/
static inline int set_4byte(struct m25p *flash, u32 jedec_id, int enable)
{
+ int status;
+ bool need_wren = false;
+
switch (JEDEC_MFR(jedec_id)) {
- case CFI_MFR_MACRONIX:
case CFI_MFR_ST: /* Micron, actually */
+ /* Some Micron need WREN command; all will accept it */
+ need_wren = true;
+ case CFI_MFR_MACRONIX:
case 0xEF /* winbond */:
+ if (need_wren)
+ write_enable(flash);
+
flash->command[0] = enable ? OPCODE_EN4B : OPCODE_EX4B;
- return spi_write(flash->spi, flash->command, 1);
+ status = spi_write(flash->spi, flash->command, 1);
+
+ if (need_wren)
+ write_disable(flash);
+
+ return status;
default:
/* Spansion style */
flash->command[0] = OPCODE_BRWR;
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
index 7ed4841..d340b2f 100644
--- a/drivers/mtd/nand/nand_base.c
+++ b/drivers/mtd/nand/nand_base.c
@@ -2869,10 +2869,8 @@
len = le16_to_cpu(p->ext_param_page_length) * 16;
ep = kmalloc(len, GFP_KERNEL);
- if (!ep) {
- ret = -ENOMEM;
- goto ext_out;
- }
+ if (!ep)
+ return -ENOMEM;
/* Send our own NAND_CMD_PARAM. */
chip->cmdfunc(mtd, NAND_CMD_PARAM, 0, -1);
@@ -2920,7 +2918,7 @@
}
pr_info("ONFI extended param page detected.\n");
- return 0;
+ ret = 0;
ext_out:
kfree(ep);
diff --git a/drivers/pinctrl/pinctrl-single.c b/drivers/pinctrl/pinctrl-single.c
index a82ace4..0846922 100644
--- a/drivers/pinctrl/pinctrl-single.c
+++ b/drivers/pinctrl/pinctrl-single.c
@@ -15,15 +15,21 @@
#include <linux/slab.h>
#include <linux/err.h>
#include <linux/list.h>
+#include <linux/interrupt.h>
+
+#include <linux/irqchip/chained_irq.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/of_address.h>
+#include <linux/of_irq.h>
#include <linux/pinctrl/pinctrl.h>
#include <linux/pinctrl/pinmux.h>
#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/platform_data/pinctrl-single.h>
+
#include "core.h"
#include "pinconf.h"
@@ -150,19 +156,36 @@
};
/**
+ * struct pcs_soc_data - SoC specific settings
+ * @flags: initial SoC specific PCS_FEAT_xxx values
+ * @irq: optional interrupt for the controller
+ * @irq_enable_mask: optional SoC specific interrupt enable mask
+ * @irq_status_mask: optional SoC specific interrupt status mask
+ * @rearm: optional SoC specific wake-up rearm function
+ */
+struct pcs_soc_data {
+ unsigned flags;
+ int irq;
+ unsigned irq_enable_mask;
+ unsigned irq_status_mask;
+ void (*rearm)(void);
+};
+
+/**
* struct pcs_device - pinctrl device instance
* @res: resources
* @base: virtual address of the controller
* @size: size of the ioremapped area
* @dev: device entry
* @pctl: pin controller device
+ * @flags: mask of PCS_FEAT_xxx values
+ * @lock: spinlock for register access
* @mutex: mutex protecting the lists
* @width: bits per mux register
* @fmask: function register mask
* @fshift: function register shift
* @foff: value to turn mux off
* @fmax: max number of functions in fmask
- * @is_pinconf: whether supports pinconf
* @bits_per_pin:number of bits per pin
* @names: array of register names for pins
* @pins: physical pins on the SoC
@@ -171,6 +194,9 @@
* @pingroups: list of pingroups
* @functions: list of functions
* @gpiofuncs: list of gpio functions
+ * @irqs: list of interrupt registers
+ * @chip: chip container for this instance
+ * @domain: IRQ domain for this instance
* @ngroups: number of pingroups
* @nfuncs: number of functions
* @desc: pin controller descriptor
@@ -183,6 +209,12 @@
unsigned size;
struct device *dev;
struct pinctrl_dev *pctl;
+ unsigned flags;
+#define PCS_QUIRK_SHARED_IRQ (1 << 2)
+#define PCS_FEAT_IRQ (1 << 1)
+#define PCS_FEAT_PINCONF (1 << 0)
+ struct pcs_soc_data socdata;
+ raw_spinlock_t lock;
struct mutex mutex;
unsigned width;
unsigned fmask;
@@ -190,7 +222,6 @@
unsigned foff;
unsigned fmax;
bool bits_per_mux;
- bool is_pinconf;
unsigned bits_per_pin;
struct pcs_name *names;
struct pcs_data pins;
@@ -199,6 +230,9 @@
struct list_head pingroups;
struct list_head functions;
struct list_head gpiofuncs;
+ struct list_head irqs;
+ struct irq_chip chip;
+ struct irq_domain *domain;
unsigned ngroups;
unsigned nfuncs;
struct pinctrl_desc desc;
@@ -206,6 +240,10 @@
void (*write)(unsigned val, void __iomem *reg);
};
+#define PCS_QUIRK_HAS_SHARED_IRQ (pcs->flags & PCS_QUIRK_SHARED_IRQ)
+#define PCS_HAS_IRQ (pcs->flags & PCS_FEAT_IRQ)
+#define PCS_HAS_PINCONF (pcs->flags & PCS_FEAT_PINCONF)
+
static int pcs_pinconf_get(struct pinctrl_dev *pctldev, unsigned pin,
unsigned long *config);
static int pcs_pinconf_set(struct pinctrl_dev *pctldev, unsigned pin,
@@ -429,9 +467,11 @@
for (i = 0; i < func->nvals; i++) {
struct pcs_func_vals *vals;
+ unsigned long flags;
unsigned val, mask;
vals = &func->vals[i];
+ raw_spin_lock_irqsave(&pcs->lock, flags);
val = pcs->read(vals->reg);
if (pcs->bits_per_mux)
@@ -442,6 +482,7 @@
val &= ~mask;
val |= (vals->val & mask);
pcs->write(val, vals->reg);
+ raw_spin_unlock_irqrestore(&pcs->lock, flags);
}
return 0;
@@ -483,13 +524,16 @@
for (i = 0; i < func->nvals; i++) {
struct pcs_func_vals *vals;
+ unsigned long flags;
unsigned val;
vals = &func->vals[i];
+ raw_spin_lock_irqsave(&pcs->lock, flags);
val = pcs->read(vals->reg);
val &= ~pcs->fmask;
val |= pcs->foff << pcs->fshift;
pcs->write(val, vals->reg);
+ raw_spin_unlock_irqrestore(&pcs->lock, flags);
}
}
@@ -1060,7 +1104,7 @@
};
/* If pinconf isn't supported, don't parse properties in below. */
- if (!pcs->is_pinconf)
+ if (!PCS_HAS_PINCONF)
return 0;
/* cacluate how much properties are supported in current node */
@@ -1184,7 +1228,7 @@
(*map)->data.mux.group = np->name;
(*map)->data.mux.function = np->name;
- if (pcs->is_pinconf) {
+ if (PCS_HAS_PINCONF) {
res = pcs_parse_pinconf(pcs, np, function, map);
if (res)
goto free_pingroups;
@@ -1305,7 +1349,7 @@
(*map)->data.mux.group = np->name;
(*map)->data.mux.function = np->name;
- if (pcs->is_pinconf) {
+ if (PCS_HAS_PINCONF) {
dev_err(pcs->dev, "pinconf not supported\n");
goto free_pingroups;
}
@@ -1440,11 +1484,33 @@
}
/**
+ * pcs_irq_free() - free interrupt
+ * @pcs: pcs driver instance
+ */
+static void pcs_irq_free(struct pcs_device *pcs)
+{
+ struct pcs_soc_data *pcs_soc = &pcs->socdata;
+
+ if (pcs_soc->irq < 0)
+ return;
+
+ if (pcs->domain)
+ irq_domain_remove(pcs->domain);
+
+ if (PCS_QUIRK_HAS_SHARED_IRQ)
+ free_irq(pcs_soc->irq, pcs_soc);
+ else
+ irq_set_chained_handler(pcs_soc->irq, NULL);
+}
+
+/**
* pcs_free_resources() - free memory used by this driver
* @pcs: pcs driver instance
*/
static void pcs_free_resources(struct pcs_device *pcs)
{
+ pcs_irq_free(pcs);
+
if (pcs->pctl)
pinctrl_unregister(pcs->pctl);
@@ -1493,6 +1559,268 @@
}
return ret;
}
+/**
+ * @reg: virtual address of interrupt register
+ * @hwirq: hardware irq number
+ * @irq: virtual irq number
+ * @node: list node
+ */
+struct pcs_interrupt {
+ void __iomem *reg;
+ irq_hw_number_t hwirq;
+ unsigned int irq;
+ struct list_head node;
+};
+
+/**
+ * pcs_irq_set() - enables or disables an interrupt
+ *
+ * Note that this currently assumes one interrupt per pinctrl
+ * register that is typically used for wake-up events.
+ */
+static inline void pcs_irq_set(struct pcs_soc_data *pcs_soc,
+ int irq, const bool enable)
+{
+ struct pcs_device *pcs;
+ struct list_head *pos;
+ unsigned mask;
+
+ pcs = container_of(pcs_soc, struct pcs_device, socdata);
+ list_for_each(pos, &pcs->irqs) {
+ struct pcs_interrupt *pcswi;
+ unsigned soc_mask;
+
+ pcswi = list_entry(pos, struct pcs_interrupt, node);
+ if (irq != pcswi->irq)
+ continue;
+
+ soc_mask = pcs_soc->irq_enable_mask;
+ raw_spin_lock(&pcs->lock);
+ mask = pcs->read(pcswi->reg);
+ if (enable)
+ mask |= soc_mask;
+ else
+ mask &= ~soc_mask;
+ pcs->write(mask, pcswi->reg);
+ raw_spin_unlock(&pcs->lock);
+ }
+}
+
+/**
+ * pcs_irq_mask() - mask pinctrl interrupt
+ * @d: interrupt data
+ */
+static void pcs_irq_mask(struct irq_data *d)
+{
+ struct pcs_soc_data *pcs_soc = irq_data_get_irq_chip_data(d);
+
+ pcs_irq_set(pcs_soc, d->irq, false);
+}
+
+/**
+ * pcs_irq_unmask() - unmask pinctrl interrupt
+ * @d: interrupt data
+ */
+static void pcs_irq_unmask(struct irq_data *d)
+{
+ struct pcs_soc_data *pcs_soc = irq_data_get_irq_chip_data(d);
+
+ pcs_irq_set(pcs_soc, d->irq, true);
+ if (pcs_soc->rearm)
+ pcs_soc->rearm();
+}
+
+/**
+ * pcs_irq_set_wake() - toggle the suspend and resume wake up
+ * @d: interrupt data
+ * @state: wake-up state
+ *
+ * Note that this should be called only for suspend and resume.
+ * For runtime PM, the wake-up events should be enabled by default.
+ */
+static int pcs_irq_set_wake(struct irq_data *d, unsigned int state)
+{
+ if (state)
+ pcs_irq_unmask(d);
+ else
+ pcs_irq_mask(d);
+
+ return 0;
+}
+
+/**
+ * pcs_irq_handle() - common interrupt handler
+ * @pcs_irq: interrupt data
+ *
+ * Note that this currently assumes we have one interrupt bit per
+ * mux register. This interrupt is typically used for wake-up events.
+ * For more complex interrupts different handlers can be specified.
+ */
+static int pcs_irq_handle(struct pcs_soc_data *pcs_soc)
+{
+ struct pcs_device *pcs;
+ struct list_head *pos;
+ int count = 0;
+
+ pcs = container_of(pcs_soc, struct pcs_device, socdata);
+ list_for_each(pos, &pcs->irqs) {
+ struct pcs_interrupt *pcswi;
+ unsigned mask;
+
+ pcswi = list_entry(pos, struct pcs_interrupt, node);
+ raw_spin_lock(&pcs->lock);
+ mask = pcs->read(pcswi->reg);
+ raw_spin_unlock(&pcs->lock);
+ if (mask & pcs_soc->irq_status_mask) {
+ generic_handle_irq(irq_find_mapping(pcs->domain,
+ pcswi->hwirq));
+ count++;
+ }
+ }
+
+ /*
+ * For debugging on omaps, you may want to call pcs_soc->rearm()
+ * here to see wake-up interrupts during runtime also.
+ */
+
+ return count;
+}
+
+/**
+ * pcs_irq_handler() - handler for the shared interrupt case
+ * @irq: interrupt
+ * @d: data
+ *
+ * Use this for cases where multiple instances of
+ * pinctrl-single share a single interrupt like on omaps.
+ */
+static irqreturn_t pcs_irq_handler(int irq, void *d)
+{
+ struct pcs_soc_data *pcs_soc = d;
+
+ return pcs_irq_handle(pcs_soc) ? IRQ_HANDLED : IRQ_NONE;
+}
+
+/**
+ * pcs_irq_handle() - handler for the dedicated chained interrupt case
+ * @irq: interrupt
+ * @desc: interrupt descriptor
+ *
+ * Use this if you have a separate interrupt for each
+ * pinctrl-single instance.
+ */
+static void pcs_irq_chain_handler(unsigned int irq, struct irq_desc *desc)
+{
+ struct pcs_soc_data *pcs_soc = irq_desc_get_handler_data(desc);
+ struct irq_chip *chip;
+ int res;
+
+ chip = irq_get_chip(irq);
+ chained_irq_enter(chip, desc);
+ res = pcs_irq_handle(pcs_soc);
+ /* REVISIT: export and add handle_bad_irq(irq, desc)? */
+ chained_irq_exit(chip, desc);
+
+ return;
+}
+
+static int pcs_irqdomain_map(struct irq_domain *d, unsigned int irq,
+ irq_hw_number_t hwirq)
+{
+ struct pcs_soc_data *pcs_soc = d->host_data;
+ struct pcs_device *pcs;
+ struct pcs_interrupt *pcswi;
+
+ pcs = container_of(pcs_soc, struct pcs_device, socdata);
+ pcswi = devm_kzalloc(pcs->dev, sizeof(*pcswi), GFP_KERNEL);
+ if (!pcswi)
+ return -ENOMEM;
+
+ pcswi->reg = pcs->base + hwirq;
+ pcswi->hwirq = hwirq;
+ pcswi->irq = irq;
+
+ mutex_lock(&pcs->mutex);
+ list_add_tail(&pcswi->node, &pcs->irqs);
+ mutex_unlock(&pcs->mutex);
+
+ irq_set_chip_data(irq, pcs_soc);
+ irq_set_chip_and_handler(irq, &pcs->chip,
+ handle_level_irq);
+
+#ifdef CONFIG_ARM
+ set_irq_flags(irq, IRQF_VALID);
+#else
+ irq_set_noprobe(irq);
+#endif
+
+ return 0;
+}
+
+static struct irq_domain_ops pcs_irqdomain_ops = {
+ .map = pcs_irqdomain_map,
+ .xlate = irq_domain_xlate_onecell,
+};
+
+/**
+ * pcs_irq_init_chained_handler() - set up a chained interrupt handler
+ * @pcs: pcs driver instance
+ * @np: device node pointer
+ */
+static int pcs_irq_init_chained_handler(struct pcs_device *pcs,
+ struct device_node *np)
+{
+ struct pcs_soc_data *pcs_soc = &pcs->socdata;
+ const char *name = "pinctrl";
+ int num_irqs;
+
+ if (!pcs_soc->irq_enable_mask ||
+ !pcs_soc->irq_status_mask) {
+ pcs_soc->irq = -1;
+ return -EINVAL;
+ }
+
+ INIT_LIST_HEAD(&pcs->irqs);
+ pcs->chip.name = name;
+ pcs->chip.irq_ack = pcs_irq_mask;
+ pcs->chip.irq_mask = pcs_irq_mask;
+ pcs->chip.irq_unmask = pcs_irq_unmask;
+ pcs->chip.irq_set_wake = pcs_irq_set_wake;
+
+ if (PCS_QUIRK_HAS_SHARED_IRQ) {
+ int res;
+
+ res = request_irq(pcs_soc->irq, pcs_irq_handler,
+ IRQF_SHARED | IRQF_NO_SUSPEND,
+ name, pcs_soc);
+ if (res) {
+ pcs_soc->irq = -1;
+ return res;
+ }
+ } else {
+ irq_set_handler_data(pcs_soc->irq, pcs_soc);
+ irq_set_chained_handler(pcs_soc->irq,
+ pcs_irq_chain_handler);
+ }
+
+ /*
+ * We can use the register offset as the hardirq
+ * number as irq_domain_add_simple maps them lazily.
+ * This way we can easily support more than one
+ * interrupt per function if needed.
+ */
+ num_irqs = pcs->size;
+
+ pcs->domain = irq_domain_add_simple(np, num_irqs, 0,
+ &pcs_irqdomain_ops,
+ pcs_soc);
+ if (!pcs->domain) {
+ irq_set_chained_handler(pcs_soc->irq, NULL);
+ return -EINVAL;
+ }
+
+ return 0;
+}
#ifdef CONFIG_PM
static int pinctrl_single_suspend(struct platform_device *pdev,
@@ -1523,8 +1851,10 @@
{
struct device_node *np = pdev->dev.of_node;
const struct of_device_id *match;
+ struct pcs_pdata *pdata;
struct resource *res;
struct pcs_device *pcs;
+ const struct pcs_soc_data *soc;
int ret;
match = of_match_device(pcs_of_match, &pdev->dev);
@@ -1537,11 +1867,14 @@
return -ENOMEM;
}
pcs->dev = &pdev->dev;
+ raw_spin_lock_init(&pcs->lock);
mutex_init(&pcs->mutex);
INIT_LIST_HEAD(&pcs->pingroups);
INIT_LIST_HEAD(&pcs->functions);
INIT_LIST_HEAD(&pcs->gpiofuncs);
- pcs->is_pinconf = match->data;
+ soc = match->data;
+ pcs->flags = soc->flags;
+ memcpy(&pcs->socdata, soc, sizeof(*soc));
PCS_GET_PROP_U32("pinctrl-single,register-width", &pcs->width,
"register width not specified\n");
@@ -1610,7 +1943,7 @@
pcs->desc.name = DRIVER_NAME;
pcs->desc.pctlops = &pcs_pinctrl_ops;
pcs->desc.pmxops = &pcs_pinmux_ops;
- if (pcs->is_pinconf)
+ if (PCS_HAS_PINCONF)
pcs->desc.confops = &pcs_pinconf_ops;
pcs->desc.owner = THIS_MODULE;
@@ -1629,6 +1962,27 @@
if (ret < 0)
goto free;
+ pcs->socdata.irq = irq_of_parse_and_map(np, 0);
+ if (pcs->socdata.irq)
+ pcs->flags |= PCS_FEAT_IRQ;
+
+ /* We still need auxdata for some omaps for PRM interrupts */
+ pdata = dev_get_platdata(&pdev->dev);
+ if (pdata) {
+ if (pdata->rearm)
+ pcs->socdata.rearm = pdata->rearm;
+ if (pdata->irq) {
+ pcs->socdata.irq = pdata->irq;
+ pcs->flags |= PCS_FEAT_IRQ;
+ }
+ }
+
+ if (PCS_HAS_IRQ) {
+ ret = pcs_irq_init_chained_handler(pcs, np);
+ if (ret < 0)
+ dev_warn(pcs->dev, "initialized with no interrupts\n");
+ }
+
dev_info(pcs->dev, "%i pins at pa %p size %u\n",
pcs->desc.npins, pcs->base, pcs->size);
@@ -1652,9 +2006,25 @@
return 0;
}
+static const struct pcs_soc_data pinctrl_single_omap_wkup = {
+ .flags = PCS_QUIRK_SHARED_IRQ,
+ .irq_enable_mask = (1 << 14), /* OMAP_WAKEUP_EN */
+ .irq_status_mask = (1 << 15), /* OMAP_WAKEUP_EVENT */
+};
+
+static const struct pcs_soc_data pinctrl_single = {
+};
+
+static const struct pcs_soc_data pinconf_single = {
+ .flags = PCS_FEAT_PINCONF,
+};
+
static struct of_device_id pcs_of_match[] = {
- { .compatible = "pinctrl-single", .data = (void *)false },
- { .compatible = "pinconf-single", .data = (void *)true },
+ { .compatible = "ti,omap3-padconf", .data = &pinctrl_single_omap_wkup },
+ { .compatible = "ti,omap4-padconf", .data = &pinctrl_single_omap_wkup },
+ { .compatible = "ti,omap5-padconf", .data = &pinctrl_single_omap_wkup },
+ { .compatible = "pinctrl-single", .data = &pinctrl_single },
+ { .compatible = "pinconf-single", .data = &pinconf_single },
{ },
};
MODULE_DEVICE_TABLE(of, pcs_of_match);
diff --git a/drivers/s390/char/sclp_cmd.c b/drivers/s390/char/sclp_cmd.c
index 8cd34bf..77df9cb 100644
--- a/drivers/s390/char/sclp_cmd.c
+++ b/drivers/s390/char/sclp_cmd.c
@@ -145,9 +145,11 @@
if (sccb->header.response_code != 0x20)
return 0;
- if (sccb->sclp_send_mask & (EVTYP_MSG_MASK | EVTYP_PMSGCMD_MASK))
- return 1;
- return 0;
+ if (!(sccb->sclp_send_mask & (EVTYP_OPCMD_MASK | EVTYP_PMSGCMD_MASK)))
+ return 0;
+ if (!(sccb->sclp_receive_mask & (EVTYP_MSG_MASK | EVTYP_PMSGCMD_MASK)))
+ return 0;
+ return 1;
}
bool __init sclp_has_vt220(void)
diff --git a/drivers/s390/char/tty3270.c b/drivers/s390/char/tty3270.c
index a0f47c8..3f4ca4e 100644
--- a/drivers/s390/char/tty3270.c
+++ b/drivers/s390/char/tty3270.c
@@ -810,7 +810,7 @@
struct winsize ws;
screen = tty3270_alloc_screen(tp->n_rows, tp->n_cols);
- if (!screen)
+ if (IS_ERR(screen))
return;
/* Switch to new output size */
spin_lock_bh(&tp->view.lock);
diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c
index fd7cc56..d4ac60b 100644
--- a/drivers/spi/spi-atmel.c
+++ b/drivers/spi/spi-atmel.c
@@ -1583,7 +1583,7 @@
/* Initialize the hardware */
ret = clk_prepare_enable(clk);
if (ret)
- goto out_unmap_regs;
+ goto out_free_irq;
spi_writel(as, CR, SPI_BIT(SWRST));
spi_writel(as, CR, SPI_BIT(SWRST)); /* AT91SAM9263 Rev B workaround */
if (as->caps.has_wdrbt) {
@@ -1614,6 +1614,7 @@
spi_writel(as, CR, SPI_BIT(SWRST));
spi_writel(as, CR, SPI_BIT(SWRST)); /* AT91SAM9263 Rev B workaround */
clk_disable_unprepare(clk);
+out_free_irq:
free_irq(irq, master);
out_unmap_regs:
iounmap(as->regs);
diff --git a/drivers/spi/spi-clps711x.c b/drivers/spi/spi-clps711x.c
index 5655acf..6416798 100644
--- a/drivers/spi/spi-clps711x.c
+++ b/drivers/spi/spi-clps711x.c
@@ -226,7 +226,6 @@
dev_name(&pdev->dev), hw);
if (ret) {
dev_err(&pdev->dev, "Can't request IRQ\n");
- clk_put(hw->spi_clk);
goto clk_out;
}
@@ -247,7 +246,6 @@
gpio_free(hw->chipselect[i]);
spi_master_put(master);
- kfree(master);
return ret;
}
@@ -263,7 +261,6 @@
gpio_free(hw->chipselect[i]);
spi_unregister_master(master);
- kfree(master);
return 0;
}
diff --git a/drivers/spi/spi-fsl-dspi.c b/drivers/spi/spi-fsl-dspi.c
index 6cd07d1..4e44575 100644
--- a/drivers/spi/spi-fsl-dspi.c
+++ b/drivers/spi/spi-fsl-dspi.c
@@ -476,15 +476,9 @@
master->bus_num = bus_num;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!res) {
- dev_err(&pdev->dev, "can't get platform resource\n");
- ret = -EINVAL;
- goto out_master_put;
- }
-
dspi->base = devm_ioremap_resource(&pdev->dev, res);
- if (!dspi->base) {
- ret = -EINVAL;
+ if (IS_ERR(dspi->base)) {
+ ret = PTR_ERR(dspi->base);
goto out_master_put;
}
diff --git a/drivers/spi/spi-mpc512x-psc.c b/drivers/spi/spi-mpc512x-psc.c
index dbc5e99..6adf4e3 100644
--- a/drivers/spi/spi-mpc512x-psc.c
+++ b/drivers/spi/spi-mpc512x-psc.c
@@ -522,8 +522,10 @@
psc_num = master->bus_num;
snprintf(clk_name, sizeof(clk_name), "psc%d_mclk", psc_num);
clk = devm_clk_get(dev, clk_name);
- if (IS_ERR(clk))
+ if (IS_ERR(clk)) {
+ ret = PTR_ERR(clk);
goto free_irq;
+ }
ret = clk_prepare_enable(clk);
if (ret)
goto free_irq;
diff --git a/drivers/spi/spi-pxa2xx.c b/drivers/spi/spi-pxa2xx.c
index 2eb06ee..c1a5067 100644
--- a/drivers/spi/spi-pxa2xx.c
+++ b/drivers/spi/spi-pxa2xx.c
@@ -546,8 +546,17 @@
if (pm_runtime_suspended(&drv_data->pdev->dev))
return IRQ_NONE;
- sccr1_reg = read_SSCR1(reg);
+ /*
+ * If the device is not yet in RPM suspended state and we get an
+ * interrupt that is meant for another device, check if status bits
+ * are all set to one. That means that the device is already
+ * powered off.
+ */
status = read_SSSR(reg);
+ if (status == ~0)
+ return IRQ_NONE;
+
+ sccr1_reg = read_SSCR1(reg);
/* Ignore possible writes if we don't need to write */
if (!(sccr1_reg & SSCR1_TIE))
diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c
index 512b8893..a80376d 100644
--- a/drivers/spi/spi-s3c64xx.c
+++ b/drivers/spi/spi-s3c64xx.c
@@ -1428,6 +1428,8 @@
S3C64XX_SPI_INT_TX_OVERRUN_EN | S3C64XX_SPI_INT_TX_UNDERRUN_EN,
sdd->regs + S3C64XX_SPI_INT_EN);
+ pm_runtime_enable(&pdev->dev);
+
if (spi_register_master(master)) {
dev_err(&pdev->dev, "cannot register SPI master\n");
ret = -EBUSY;
@@ -1440,8 +1442,6 @@
mem_res,
sdd->rx_dma.dmach, sdd->tx_dma.dmach);
- pm_runtime_enable(&pdev->dev);
-
return 0;
err3:
diff --git a/drivers/spi/spi-sh-hspi.c b/drivers/spi/spi-sh-hspi.c
index 0b68cb5..e488a90 100644
--- a/drivers/spi/spi-sh-hspi.c
+++ b/drivers/spi/spi-sh-hspi.c
@@ -296,6 +296,8 @@
goto error1;
}
+ pm_runtime_enable(&pdev->dev);
+
master->num_chipselect = 1;
master->bus_num = pdev->id;
master->setup = hspi_setup;
@@ -309,8 +311,6 @@
goto error1;
}
- pm_runtime_enable(&pdev->dev);
-
return 0;
error1:
diff --git a/drivers/usb/host/ohci-s3c2410.c b/drivers/usb/host/ohci-s3c2410.c
index 4919afa..1adff32 100644
--- a/drivers/usb/host/ohci-s3c2410.c
+++ b/drivers/usb/host/ohci-s3c2410.c
@@ -47,10 +47,10 @@
dev_dbg(&dev->dev, "s3c2410_start_hc:\n");
- clk_enable(usb_clk);
+ clk_prepare_enable(usb_clk);
mdelay(2); /* let the bus clock stabilise */
- clk_enable(clk);
+ clk_prepare_enable(clk);
if (info != NULL) {
info->hcd = hcd;
@@ -75,8 +75,8 @@
(info->enable_oc)(info, 0);
}
- clk_disable(clk);
- clk_disable(usb_clk);
+ clk_disable_unprepare(clk);
+ clk_disable_unprepare(usb_clk);
}
/* ohci_s3c2410_hub_status_data
diff --git a/drivers/usb/musb/ux500.c b/drivers/usb/musb/ux500.c
index 59256b1..c844499 100644
--- a/drivers/usb/musb/ux500.c
+++ b/drivers/usb/musb/ux500.c
@@ -259,7 +259,7 @@
goto err1;
}
- clk = clk_get(&pdev->dev, "usb");
+ clk = clk_get(&pdev->dev, NULL);
if (IS_ERR(clk)) {
dev_err(&pdev->dev, "failed to get clock\n");
ret = PTR_ERR(clk);
diff --git a/drivers/watchdog/hpwdt.c b/drivers/watchdog/hpwdt.c
index 5be5e3d..19f3c3f 100644
--- a/drivers/watchdog/hpwdt.c
+++ b/drivers/watchdog/hpwdt.c
@@ -802,6 +802,12 @@
return -ENODEV;
}
+ /*
+ * Ignore all auxilary iLO devices with the following PCI ID
+ */
+ if (dev->subsystem_device == 0x1979)
+ return -ENODEV;
+
if (pci_enable_device(dev)) {
dev_warn(&dev->dev,
"Not possible to enable PCI Device: 0x%x:0x%x.\n",
diff --git a/drivers/watchdog/kempld_wdt.c b/drivers/watchdog/kempld_wdt.c
index 491419e..5c3d4df 100644
--- a/drivers/watchdog/kempld_wdt.c
+++ b/drivers/watchdog/kempld_wdt.c
@@ -35,7 +35,7 @@
#define KEMPLD_WDT_STAGE_TIMEOUT(x) (0x1b + (x) * 4)
#define KEMPLD_WDT_STAGE_CFG(x) (0x18 + (x))
#define STAGE_CFG_GET_PRESCALER(x) (((x) & 0x30) >> 4)
-#define STAGE_CFG_SET_PRESCALER(x) (((x) & 0x30) << 4)
+#define STAGE_CFG_SET_PRESCALER(x) (((x) & 0x3) << 4)
#define STAGE_CFG_PRESCALER_MASK 0x30
#define STAGE_CFG_ACTION_MASK 0x7
#define STAGE_CFG_ASSERT (1 << 3)
diff --git a/drivers/watchdog/sunxi_wdt.c b/drivers/watchdog/sunxi_wdt.c
index 1f94b42..f6caa771 100644
--- a/drivers/watchdog/sunxi_wdt.c
+++ b/drivers/watchdog/sunxi_wdt.c
@@ -146,7 +146,7 @@
.set_timeout = sunxi_wdt_set_timeout,
};
-static int __init sunxi_wdt_probe(struct platform_device *pdev)
+static int sunxi_wdt_probe(struct platform_device *pdev)
{
struct sunxi_wdt_dev *sunxi_wdt;
struct resource *res;
@@ -187,7 +187,7 @@
return 0;
}
-static int __exit sunxi_wdt_remove(struct platform_device *pdev)
+static int sunxi_wdt_remove(struct platform_device *pdev)
{
struct sunxi_wdt_dev *sunxi_wdt = platform_get_drvdata(pdev);
diff --git a/drivers/watchdog/ts72xx_wdt.c b/drivers/watchdog/ts72xx_wdt.c
index 42913f1..c9b0c62 100644
--- a/drivers/watchdog/ts72xx_wdt.c
+++ b/drivers/watchdog/ts72xx_wdt.c
@@ -310,7 +310,8 @@
case WDIOC_GETSTATUS:
case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
+ error = put_user(0, p);
+ break;
case WDIOC_KEEPALIVE:
ts72xx_wdt_kick(wdt);
diff --git a/fs/btrfs/disk-io.c b/fs/btrfs/disk-io.c
index 4ae17ed..62176ad8 100644
--- a/fs/btrfs/disk-io.c
+++ b/fs/btrfs/disk-io.c
@@ -1561,8 +1561,9 @@
return ret;
}
-struct btrfs_root *btrfs_read_fs_root_no_name(struct btrfs_fs_info *fs_info,
- struct btrfs_key *location)
+struct btrfs_root *btrfs_get_fs_root(struct btrfs_fs_info *fs_info,
+ struct btrfs_key *location,
+ bool check_ref)
{
struct btrfs_root *root;
int ret;
@@ -1586,7 +1587,7 @@
again:
root = btrfs_lookup_fs_root(fs_info, location->objectid);
if (root) {
- if (btrfs_root_refs(&root->root_item) == 0)
+ if (check_ref && btrfs_root_refs(&root->root_item) == 0)
return ERR_PTR(-ENOENT);
return root;
}
@@ -1595,7 +1596,7 @@
if (IS_ERR(root))
return root;
- if (btrfs_root_refs(&root->root_item) == 0) {
+ if (check_ref && btrfs_root_refs(&root->root_item) == 0) {
ret = -ENOENT;
goto fail;
}
diff --git a/fs/btrfs/disk-io.h b/fs/btrfs/disk-io.h
index b71acd6e..5ce2a7d 100644
--- a/fs/btrfs/disk-io.h
+++ b/fs/btrfs/disk-io.h
@@ -68,8 +68,17 @@
int btrfs_init_fs_root(struct btrfs_root *root);
int btrfs_insert_fs_root(struct btrfs_fs_info *fs_info,
struct btrfs_root *root);
-struct btrfs_root *btrfs_read_fs_root_no_name(struct btrfs_fs_info *fs_info,
- struct btrfs_key *location);
+
+struct btrfs_root *btrfs_get_fs_root(struct btrfs_fs_info *fs_info,
+ struct btrfs_key *key,
+ bool check_ref);
+static inline struct btrfs_root *
+btrfs_read_fs_root_no_name(struct btrfs_fs_info *fs_info,
+ struct btrfs_key *location)
+{
+ return btrfs_get_fs_root(fs_info, location, true);
+}
+
int btrfs_cleanup_fs_roots(struct btrfs_fs_info *fs_info);
void btrfs_btree_balance_dirty(struct btrfs_root *root);
void btrfs_btree_balance_dirty_nodelay(struct btrfs_root *root);
diff --git a/fs/btrfs/extent_io.c b/fs/btrfs/extent_io.c
index 22bda32..51731b7 100644
--- a/fs/btrfs/extent_io.c
+++ b/fs/btrfs/extent_io.c
@@ -1490,10 +1490,8 @@
cur_start = state->end + 1;
node = rb_next(node);
total_bytes += state->end - state->start + 1;
- if (total_bytes >= max_bytes) {
- *end = *start + max_bytes - 1;
+ if (total_bytes >= max_bytes)
break;
- }
if (!node)
break;
}
@@ -1635,10 +1633,9 @@
/*
* make sure to limit the number of pages we try to lock down
- * if we're looping.
*/
- if (delalloc_end + 1 - delalloc_start > max_bytes && loops)
- delalloc_end = delalloc_start + PAGE_CACHE_SIZE - 1;
+ if (delalloc_end + 1 - delalloc_start > max_bytes)
+ delalloc_end = delalloc_start + max_bytes - 1;
/* step two, lock all the pages after the page that has start */
ret = lock_delalloc_pages(inode, locked_page,
@@ -1649,8 +1646,7 @@
*/
free_extent_state(cached_state);
if (!loops) {
- unsigned long offset = (*start) & (PAGE_CACHE_SIZE - 1);
- max_bytes = PAGE_CACHE_SIZE - offset;
+ max_bytes = PAGE_CACHE_SIZE;
loops = 1;
goto again;
} else {
diff --git a/fs/btrfs/inode.c b/fs/btrfs/inode.c
index 22ebc13..b0ef7b0 100644
--- a/fs/btrfs/inode.c
+++ b/fs/btrfs/inode.c
@@ -7986,7 +7986,7 @@
/* check for collisions, even if the name isn't there */
- ret = btrfs_check_dir_item_collision(root, new_dir->i_ino,
+ ret = btrfs_check_dir_item_collision(dest, new_dir->i_ino,
new_dentry->d_name.name,
new_dentry->d_name.len);
diff --git a/fs/btrfs/relocation.c b/fs/btrfs/relocation.c
index a5a2632..4a35572 100644
--- a/fs/btrfs/relocation.c
+++ b/fs/btrfs/relocation.c
@@ -588,7 +588,7 @@
else
key.offset = (u64)-1;
- return btrfs_read_fs_root_no_name(fs_info, &key);
+ return btrfs_get_fs_root(fs_info, &key, false);
}
#ifdef BTRFS_COMPAT_EXTENT_TREE_V0
diff --git a/fs/btrfs/root-tree.c b/fs/btrfs/root-tree.c
index 0b1f4ef..ec71ea4 100644
--- a/fs/btrfs/root-tree.c
+++ b/fs/btrfs/root-tree.c
@@ -299,11 +299,6 @@
continue;
}
- if (btrfs_root_refs(&root->root_item) == 0) {
- btrfs_add_dead_root(root);
- continue;
- }
-
err = btrfs_init_fs_root(root);
if (err) {
btrfs_free_fs_root(root);
@@ -318,6 +313,9 @@
btrfs_free_fs_root(root);
break;
}
+
+ if (btrfs_root_refs(&root->root_item) == 0)
+ btrfs_add_dead_root(root);
}
btrfs_free_path(path);
diff --git a/fs/ext4/inode.c b/fs/ext4/inode.c
index 0d424d7..e274e9c 100644
--- a/fs/ext4/inode.c
+++ b/fs/ext4/inode.c
@@ -2563,7 +2563,7 @@
break;
}
blk_finish_plug(&plug);
- if (!ret && !cycled) {
+ if (!ret && !cycled && wbc->nr_to_write > 0) {
cycled = 1;
mpd.last_page = writeback_index - 1;
mpd.first_page = 0;
diff --git a/fs/ext4/xattr.c b/fs/ext4/xattr.c
index c081e34..03e9beb 100644
--- a/fs/ext4/xattr.c
+++ b/fs/ext4/xattr.c
@@ -1350,6 +1350,8 @@
s_min_extra_isize) {
tried_min_extra_isize++;
new_extra_isize = s_min_extra_isize;
+ kfree(is); is = NULL;
+ kfree(bs); bs = NULL;
goto retry;
}
error = -1;
diff --git a/fs/statfs.c b/fs/statfs.c
index c219e733..083dc0a 100644
--- a/fs/statfs.c
+++ b/fs/statfs.c
@@ -94,7 +94,7 @@
int fd_statfs(int fd, struct kstatfs *st)
{
- struct fd f = fdget(fd);
+ struct fd f = fdget_raw(fd);
int error = -EBADF;
if (f.file) {
error = vfs_statfs(&f.file->f_path, st);
diff --git a/include/dt-bindings/mfd/dbx500-prcmu.h b/include/dt-bindings/mfd/dbx500-prcmu.h
new file mode 100644
index 0000000..552a2d1
--- /dev/null
+++ b/include/dt-bindings/mfd/dbx500-prcmu.h
@@ -0,0 +1,83 @@
+/*
+ * This header provides constants for the PRCMU bindings.
+ *
+ */
+
+#ifndef _DT_BINDINGS_MFD_PRCMU_H
+#define _DT_BINDINGS_MFD_PRCMU_H
+
+/*
+ * Clock identifiers.
+ */
+#define ARMCLK 0
+#define PRCMU_ACLK 1
+#define PRCMU_SVAMMCSPCLK 2
+#define PRCMU_SDMMCHCLK 2 /* DBx540 only. */
+#define PRCMU_SIACLK 3
+#define PRCMU_SIAMMDSPCLK 3 /* DBx540 only. */
+#define PRCMU_SGACLK 4
+#define PRCMU_UARTCLK 5
+#define PRCMU_MSP02CLK 6
+#define PRCMU_MSP1CLK 7
+#define PRCMU_I2CCLK 8
+#define PRCMU_SDMMCCLK 9
+#define PRCMU_SLIMCLK 10
+#define PRCMU_CAMCLK 10 /* DBx540 only. */
+#define PRCMU_PER1CLK 11
+#define PRCMU_PER2CLK 12
+#define PRCMU_PER3CLK 13
+#define PRCMU_PER5CLK 14
+#define PRCMU_PER6CLK 15
+#define PRCMU_PER7CLK 16
+#define PRCMU_LCDCLK 17
+#define PRCMU_BMLCLK 18
+#define PRCMU_HSITXCLK 19
+#define PRCMU_HSIRXCLK 20
+#define PRCMU_HDMICLK 21
+#define PRCMU_APEATCLK 22
+#define PRCMU_APETRACECLK 23
+#define PRCMU_MCDECLK 24
+#define PRCMU_IPI2CCLK 25
+#define PRCMU_DSIALTCLK 26
+#define PRCMU_DMACLK 27
+#define PRCMU_B2R2CLK 28
+#define PRCMU_TVCLK 29
+#define SPARE_UNIPROCLK 30
+#define PRCMU_SSPCLK 31
+#define PRCMU_RNGCLK 32
+#define PRCMU_UICCCLK 33
+#define PRCMU_G1CLK 34 /* DBx540 only. */
+#define PRCMU_HVACLK 35 /* DBx540 only. */
+#define PRCMU_SPARE1CLK 36
+#define PRCMU_SPARE2CLK 37
+
+#define PRCMU_NUM_REG_CLOCKS 38
+
+#define PRCMU_RTCCLK PRCMU_NUM_REG_CLOCKS
+#define PRCMU_SYSCLK 39
+#define PRCMU_CDCLK 40
+#define PRCMU_TIMCLK 41
+#define PRCMU_PLLSOC0 42
+#define PRCMU_PLLSOC1 43
+#define PRCMU_ARMSS 44
+#define PRCMU_PLLDDR 45
+
+/* DSI Clocks */
+#define PRCMU_PLLDSI 46
+#define PRCMU_DSI0CLK 47
+#define PRCMU_DSI1CLK 48
+#define PRCMU_DSI0ESCCLK 49
+#define PRCMU_DSI1ESCCLK 50
+#define PRCMU_DSI2ESCCLK 51
+
+/* LCD DSI PLL - Ux540 only */
+#define PRCMU_PLLDSI_LCD 52
+#define PRCMU_DSI0CLK_LCD 53
+#define PRCMU_DSI1CLK_LCD 54
+#define PRCMU_DSI0ESCCLK_LCD 55
+#define PRCMU_DSI1ESCCLK_LCD 56
+#define PRCMU_DSI2ESCCLK_LCD 57
+
+#define PRCMU_NUM_CLKS 58
+
+#endif
diff --git a/include/dt-bindings/pinctrl/am43xx.h b/include/dt-bindings/pinctrl/am43xx.h
new file mode 100644
index 0000000..eb6c366a
--- /dev/null
+++ b/include/dt-bindings/pinctrl/am43xx.h
@@ -0,0 +1,31 @@
+/*
+ * This header provides constants specific to AM43XX pinctrl bindings.
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_AM43XX_H
+#define _DT_BINDINGS_PINCTRL_AM43XX_H
+
+#define MUX_MODE0 0
+#define MUX_MODE1 1
+#define MUX_MODE2 2
+#define MUX_MODE3 3
+#define MUX_MODE4 4
+#define MUX_MODE5 5
+#define MUX_MODE6 6
+#define MUX_MODE7 7
+
+#define PULL_DISABLE (1 << 16)
+#define PULL_UP (1 << 17)
+#define INPUT_EN (1 << 18)
+#define SLEWCTRL_FAST (1 << 19)
+#define DS0_PULL_UP_DOWN_EN (1 << 27)
+
+#define PIN_OUTPUT (PULL_DISABLE)
+#define PIN_OUTPUT_PULLUP (PULL_UP)
+#define PIN_OUTPUT_PULLDOWN 0
+#define PIN_INPUT (INPUT_EN | PULL_DISABLE)
+#define PIN_INPUT_PULLUP (INPUT_EN | PULL_UP)
+#define PIN_INPUT_PULLDOWN (INPUT_EN)
+
+#endif
+
diff --git a/include/dt-bindings/pinctrl/dra.h b/include/dt-bindings/pinctrl/dra.h
new file mode 100644
index 0000000..002a285
--- /dev/null
+++ b/include/dt-bindings/pinctrl/dra.h
@@ -0,0 +1,50 @@
+/*
+ * This header provides constants for DRA pinctrl bindings.
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ * Author: Rajendra Nayak <rnayak@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_DRA_H
+#define _DT_BINDINGS_PINCTRL_DRA_H
+
+/* DRA7 mux mode options for each pin. See TRM for options */
+#define MUX_MODE0 0x0
+#define MUX_MODE1 0x1
+#define MUX_MODE2 0x2
+#define MUX_MODE3 0x3
+#define MUX_MODE4 0x4
+#define MUX_MODE5 0x5
+#define MUX_MODE6 0x6
+#define MUX_MODE7 0x7
+#define MUX_MODE8 0x8
+#define MUX_MODE9 0x9
+#define MUX_MODE10 0xa
+#define MUX_MODE11 0xb
+#define MUX_MODE12 0xc
+#define MUX_MODE13 0xd
+#define MUX_MODE14 0xe
+#define MUX_MODE15 0xf
+
+#define PULL_ENA (1 << 16)
+#define PULL_UP (1 << 17)
+#define INPUT_EN (1 << 18)
+#define SLEWCONTROL (1 << 19)
+#define WAKEUP_EN (1 << 24)
+#define WAKEUP_EVENT (1 << 25)
+
+/* Active pin states */
+#define PIN_OUTPUT 0
+#define PIN_OUTPUT_PULLUP (PIN_OUTPUT | PULL_ENA | PULL_UP)
+#define PIN_OUTPUT_PULLDOWN (PIN_OUTPUT | PULL_ENA)
+#define PIN_INPUT INPUT_EN
+#define PIN_INPUT_SLEW (INPUT_EN | SLEWCONTROL)
+#define PIN_INPUT_PULLUP (PULL_ENA | INPUT_EN | PULL_UP)
+#define PIN_INPUT_PULLDOWN (PULL_ENA | INPUT_EN)
+
+#endif
+
diff --git a/include/dt-bindings/pinctrl/omap.h b/include/dt-bindings/pinctrl/omap.h
index edbd250..bed35e3 100644
--- a/include/dt-bindings/pinctrl/omap.h
+++ b/include/dt-bindings/pinctrl/omap.h
@@ -23,7 +23,7 @@
#define PULL_UP (1 << 4)
#define ALTELECTRICALSEL (1 << 5)
-/* 34xx specific mux bit defines */
+/* omap3/4/5 specific mux bit defines */
#define INPUT_EN (1 << 8)
#define OFF_EN (1 << 9)
#define OFFOUT_EN (1 << 10)
@@ -31,8 +31,6 @@
#define OFF_PULL_EN (1 << 12)
#define OFF_PULL_UP (1 << 13)
#define WAKEUP_EN (1 << 14)
-
-/* 44xx specific mux bit defines */
#define WAKEUP_EVENT (1 << 15)
/* Active pin states */
diff --git a/include/linux/compiler-gcc4.h b/include/linux/compiler-gcc4.h
index 842de22..ded4299 100644
--- a/include/linux/compiler-gcc4.h
+++ b/include/linux/compiler-gcc4.h
@@ -65,6 +65,21 @@
#define __visible __attribute__((externally_visible))
#endif
+/*
+ * GCC 'asm goto' miscompiles certain code sequences:
+ *
+ * http://gcc.gnu.org/bugzilla/show_bug.cgi?id=58670
+ *
+ * Work it around via a compiler barrier quirk suggested by Jakub Jelinek.
+ * Fixed in GCC 4.8.2 and later versions.
+ *
+ * (asm goto is automatically volatile - the naming reflects this.)
+ */
+#if GCC_VERSION <= 40801
+# define asm_volatile_goto(x...) do { asm goto(x); asm (""); } while (0)
+#else
+# define asm_volatile_goto(x...) do { asm goto(x); } while (0)
+#endif
#ifdef CONFIG_ARCH_USE_BUILTIN_BSWAP
#if GCC_VERSION >= 40400
diff --git a/include/linux/mfd/dbx500-prcmu.h b/include/linux/mfd/dbx500-prcmu.h
index ca0790f..060e112 100644
--- a/include/linux/mfd/dbx500-prcmu.h
+++ b/include/linux/mfd/dbx500-prcmu.h
@@ -12,6 +12,8 @@
#include <linux/notifier.h>
#include <linux/err.h>
+#include <dt-bindings/mfd/dbx500-prcmu.h> /* For clock identifiers */
+
/* Offset for the firmware version within the TCPM */
#define DB8500_PRCMU_FW_VERSION_OFFSET 0xA4
#define DBX540_PRCMU_FW_VERSION_OFFSET 0xA8
@@ -94,74 +96,6 @@
#define PRCMU_CLKSRC_ARMCLKFIX 0x46
#define PRCMU_CLKSRC_HDMICLK 0x47
-/*
- * Clock identifiers.
- */
-enum prcmu_clock {
- PRCMU_SGACLK,
- PRCMU_UARTCLK,
- PRCMU_MSP02CLK,
- PRCMU_MSP1CLK,
- PRCMU_I2CCLK,
- PRCMU_SDMMCCLK,
- PRCMU_SPARE1CLK,
- PRCMU_SLIMCLK,
- PRCMU_PER1CLK,
- PRCMU_PER2CLK,
- PRCMU_PER3CLK,
- PRCMU_PER5CLK,
- PRCMU_PER6CLK,
- PRCMU_PER7CLK,
- PRCMU_LCDCLK,
- PRCMU_BMLCLK,
- PRCMU_HSITXCLK,
- PRCMU_HSIRXCLK,
- PRCMU_HDMICLK,
- PRCMU_APEATCLK,
- PRCMU_APETRACECLK,
- PRCMU_MCDECLK,
- PRCMU_IPI2CCLK,
- PRCMU_DSIALTCLK,
- PRCMU_DMACLK,
- PRCMU_B2R2CLK,
- PRCMU_TVCLK,
- PRCMU_SSPCLK,
- PRCMU_RNGCLK,
- PRCMU_UICCCLK,
- PRCMU_PWMCLK,
- PRCMU_IRDACLK,
- PRCMU_IRRCCLK,
- PRCMU_SIACLK,
- PRCMU_SVACLK,
- PRCMU_ACLK,
- PRCMU_HVACLK, /* Ux540 only */
- PRCMU_G1CLK, /* Ux540 only */
- PRCMU_SDMMCHCLK,
- PRCMU_CAMCLK,
- PRCMU_BML8580CLK,
- PRCMU_NUM_REG_CLOCKS,
- PRCMU_SYSCLK = PRCMU_NUM_REG_CLOCKS,
- PRCMU_CDCLK,
- PRCMU_TIMCLK,
- PRCMU_PLLSOC0,
- PRCMU_PLLSOC1,
- PRCMU_ARMSS,
- PRCMU_PLLDDR,
- PRCMU_PLLDSI,
- PRCMU_DSI0CLK,
- PRCMU_DSI1CLK,
- PRCMU_DSI0ESCCLK,
- PRCMU_DSI1ESCCLK,
- PRCMU_DSI2ESCCLK,
- /* LCD DSI PLL - Ux540 only */
- PRCMU_PLLDSI_LCD,
- PRCMU_DSI0CLK_LCD,
- PRCMU_DSI1CLK_LCD,
- PRCMU_DSI0ESCCLK_LCD,
- PRCMU_DSI1ESCCLK_LCD,
- PRCMU_DSI2ESCCLK_LCD,
-};
-
/**
* enum prcmu_wdog_id - PRCMU watchdog IDs
* @PRCMU_WDOG_ALL: use all timers
diff --git a/include/linux/miscdevice.h b/include/linux/miscdevice.h
index 09c2300..cb35835 100644
--- a/include/linux/miscdevice.h
+++ b/include/linux/miscdevice.h
@@ -45,6 +45,7 @@
#define MAPPER_CTRL_MINOR 236
#define LOOP_CTRL_MINOR 237
#define VHOST_NET_MINOR 238
+#define UHID_MINOR 239
#define MISC_DYNAMIC_MINOR 255
struct device;
diff --git a/include/linux/perf_event.h b/include/linux/perf_event.h
index 866e85c..c8ba627 100644
--- a/include/linux/perf_event.h
+++ b/include/linux/perf_event.h
@@ -294,9 +294,31 @@
*/
struct perf_event {
#ifdef CONFIG_PERF_EVENTS
- struct list_head group_entry;
+ /*
+ * entry onto perf_event_context::event_list;
+ * modifications require ctx->lock
+ * RCU safe iterations.
+ */
struct list_head event_entry;
+
+ /*
+ * XXX: group_entry and sibling_list should be mutually exclusive;
+ * either you're a sibling on a group, or you're the group leader.
+ * Rework the code to always use the same list element.
+ *
+ * Locked for modification by both ctx->mutex and ctx->lock; holding
+ * either sufficies for read.
+ */
+ struct list_head group_entry;
struct list_head sibling_list;
+
+ /*
+ * We need storage to track the entries in perf_pmu_migrate_context; we
+ * cannot use the event_entry because of RCU and we want to keep the
+ * group in tact which avoids us using the other two entries.
+ */
+ struct list_head migrate_entry;
+
struct hlist_node hlist_entry;
int nr_siblings;
int group_flags;
diff --git a/include/linux/platform_data/clk-ux500.h b/include/linux/platform_data/clk-ux500.h
index 9d98f3a..97baf83 100644
--- a/include/linux/platform_data/clk-ux500.h
+++ b/include/linux/platform_data/clk-ux500.h
@@ -10,6 +10,9 @@
#ifndef __CLK_UX500_H
#define __CLK_UX500_H
+void u8500_of_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base,
+ u32 clkrst5_base, u32 clkrst6_base);
+
void u8500_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base,
u32 clkrst5_base, u32 clkrst6_base);
void u9540_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base,
diff --git a/include/linux/platform_data/pinctrl-single.h b/include/linux/platform_data/pinctrl-single.h
new file mode 100644
index 0000000..72eacda
--- /dev/null
+++ b/include/linux/platform_data/pinctrl-single.h
@@ -0,0 +1,12 @@
+/**
+ * irq: optional wake-up interrupt
+ * rearm: optional soc specific rearm function
+ *
+ * Note that the irq and rearm setup should come from device
+ * tree except for omap where there are still some dependencies
+ * to the legacy PRM code.
+ */
+struct pcs_pdata {
+ int irq;
+ void (*rearm)(void);
+};
diff --git a/include/linux/random.h b/include/linux/random.h
index 3b9377d..6312dd9 100644
--- a/include/linux/random.h
+++ b/include/linux/random.h
@@ -17,6 +17,7 @@
extern void get_random_bytes(void *buf, int nbytes);
extern void get_random_bytes_arch(void *buf, int nbytes);
void generate_random_uuid(unsigned char uuid_out[16]);
+extern int random_int_secret_init(void);
#ifndef MODULE
extern const struct file_operations random_fops, urandom_fops;
diff --git a/include/linux/timex.h b/include/linux/timex.h
index dd3edd7..9d3f1a5 100644
--- a/include/linux/timex.h
+++ b/include/linux/timex.h
@@ -64,6 +64,20 @@
#include <asm/timex.h>
+#ifndef random_get_entropy
+/*
+ * The random_get_entropy() function is used by the /dev/random driver
+ * in order to extract entropy via the relative unpredictability of
+ * when an interrupt takes places versus a high speed, fine-grained
+ * timing source or cycle counter. Since it will be occurred on every
+ * single interrupt, it must have a very low cost/overhead.
+ *
+ * By default we use get_cycles() for this purpose, but individual
+ * architectures may override this in their asm/timex.h header file.
+ */
+#define random_get_entropy() get_cycles()
+#endif
+
/*
* SHIFT_PLL is used as a dampening factor to define how much we
* adjust the frequency correction for a given offset in PLL mode.
diff --git a/include/linux/vgaarb.h b/include/linux/vgaarb.h
index 80cf817..2c02f3a 100644
--- a/include/linux/vgaarb.h
+++ b/include/linux/vgaarb.h
@@ -65,15 +65,8 @@
* out of the arbitration process (and can be safe to take
* interrupts at any time.
*/
-#if defined(CONFIG_VGA_ARB)
extern void vga_set_legacy_decoding(struct pci_dev *pdev,
unsigned int decodes);
-#else
-static inline void vga_set_legacy_decoding(struct pci_dev *pdev,
- unsigned int decodes)
-{
-}
-#endif
/**
* vga_get - acquire & locks VGA resources
diff --git a/init/main.c b/init/main.c
index af310af..63d3e8f 100644
--- a/init/main.c
+++ b/init/main.c
@@ -76,6 +76,7 @@
#include <linux/elevator.h>
#include <linux/sched_clock.h>
#include <linux/context_tracking.h>
+#include <linux/random.h>
#include <asm/io.h>
#include <asm/bugs.h>
@@ -780,6 +781,7 @@
do_ctors();
usermodehelper_enable();
do_initcalls();
+ random_int_secret_init();
}
static void __init do_pre_smp_initcalls(void)
diff --git a/kernel/events/core.c b/kernel/events/core.c
index cb4238e..d49a9d2 100644
--- a/kernel/events/core.c
+++ b/kernel/events/core.c
@@ -7234,15 +7234,15 @@
perf_remove_from_context(event);
unaccount_event_cpu(event, src_cpu);
put_ctx(src_ctx);
- list_add(&event->event_entry, &events);
+ list_add(&event->migrate_entry, &events);
}
mutex_unlock(&src_ctx->mutex);
synchronize_rcu();
mutex_lock(&dst_ctx->mutex);
- list_for_each_entry_safe(event, tmp, &events, event_entry) {
- list_del(&event->event_entry);
+ list_for_each_entry_safe(event, tmp, &events, migrate_entry) {
+ list_del(&event->migrate_entry);
if (event->state >= PERF_EVENT_STATE_OFF)
event->state = PERF_EVENT_STATE_INACTIVE;
account_event_cpu(event, dst_cpu);
diff --git a/lib/kobject.c b/lib/kobject.c
index 669bf19..084f7b1 100644
--- a/lib/kobject.c
+++ b/lib/kobject.c
@@ -592,7 +592,7 @@
{
struct kobject *kobj = container_of(kref, struct kobject, kref);
#ifdef CONFIG_DEBUG_KOBJECT_RELEASE
- pr_debug("kobject: '%s' (%p): %s, parent %p (delayed)\n",
+ pr_info("kobject: '%s' (%p): %s, parent %p (delayed)\n",
kobject_name(kobj), kobj, __func__, kobj->parent);
INIT_DELAYED_WORK(&kobj->release, kobject_delayed_cleanup);
schedule_delayed_work(&kobj->release, HZ);
diff --git a/sound/pci/hda/patch_hdmi.c b/sound/pci/hda/patch_hdmi.c
index 7ea0245..50173d4 100644
--- a/sound/pci/hda/patch_hdmi.c
+++ b/sound/pci/hda/patch_hdmi.c
@@ -937,6 +937,14 @@
}
/*
+ * always configure channel mapping, it may have been changed by the
+ * user in the meantime
+ */
+ hdmi_setup_channel_mapping(codec, pin_nid, non_pcm, ca,
+ channels, per_pin->chmap,
+ per_pin->chmap_set);
+
+ /*
* sizeof(ai) is used instead of sizeof(*hdmi_ai) or
* sizeof(*dp_ai) to avoid partial match/update problems when
* the user switches between HDMI/DP monitors.
@@ -947,20 +955,10 @@
"pin=%d channels=%d\n",
pin_nid,
channels);
- hdmi_setup_channel_mapping(codec, pin_nid, non_pcm, ca,
- channels, per_pin->chmap,
- per_pin->chmap_set);
hdmi_stop_infoframe_trans(codec, pin_nid);
hdmi_fill_audio_infoframe(codec, pin_nid,
ai.bytes, sizeof(ai));
hdmi_start_infoframe_trans(codec, pin_nid);
- } else {
- /* For non-pcm audio switch, setup new channel mapping
- * accordingly */
- if (per_pin->non_pcm != non_pcm)
- hdmi_setup_channel_mapping(codec, pin_nid, non_pcm, ca,
- channels, per_pin->chmap,
- per_pin->chmap_set);
}
per_pin->non_pcm = non_pcm;
diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index 0e303b9..bf313bea 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -2819,6 +2819,15 @@
alc_write_coef_idx(codec, 0x1e, coef | 0x80);
}
+static void alc269_fixup_headset_mic(struct hda_codec *codec,
+ const struct hda_fixup *fix, int action)
+{
+ struct alc_spec *spec = codec->spec;
+
+ if (action == HDA_FIXUP_ACT_PRE_PROBE)
+ spec->parse_flags |= HDA_PINCFG_HEADSET_MIC;
+}
+
static void alc271_fixup_dmic(struct hda_codec *codec,
const struct hda_fixup *fix, int action)
{
@@ -3496,6 +3505,15 @@
}
}
+static void alc290_fixup_mono_speakers(struct hda_codec *codec,
+ const struct hda_fixup *fix, int action)
+{
+ if (action == HDA_FIXUP_ACT_PRE_PROBE)
+ /* Remove DAC node 0x03, as it seems to be
+ giving mono output */
+ snd_hda_override_wcaps(codec, 0x03, 0);
+}
+
enum {
ALC269_FIXUP_SONY_VAIO,
ALC275_FIXUP_SONY_VAIO_GPIO2,
@@ -3507,6 +3525,7 @@
ALC271_FIXUP_DMIC,
ALC269_FIXUP_PCM_44K,
ALC269_FIXUP_STEREO_DMIC,
+ ALC269_FIXUP_HEADSET_MIC,
ALC269_FIXUP_QUANTA_MUTE,
ALC269_FIXUP_LIFEBOOK,
ALC269_FIXUP_AMIC,
@@ -3519,9 +3538,11 @@
ALC269_FIXUP_HP_GPIO_LED,
ALC269_FIXUP_INV_DMIC,
ALC269_FIXUP_LENOVO_DOCK,
+ ALC286_FIXUP_SONY_MIC_NO_PRESENCE,
ALC269_FIXUP_PINCFG_NO_HP_TO_LINEOUT,
ALC269_FIXUP_DELL1_MIC_NO_PRESENCE,
ALC269_FIXUP_DELL2_MIC_NO_PRESENCE,
+ ALC269_FIXUP_DELL3_MIC_NO_PRESENCE,
ALC269_FIXUP_HEADSET_MODE,
ALC269_FIXUP_HEADSET_MODE_NO_HP_MIC,
ALC269_FIXUP_ASUS_X101_FUNC,
@@ -3535,6 +3556,7 @@
ALC283_FIXUP_CHROME_BOOK,
ALC282_FIXUP_ASUS_TX300,
ALC283_FIXUP_INT_MIC,
+ ALC290_FIXUP_MONO_SPEAKERS,
};
static const struct hda_fixup alc269_fixups[] = {
@@ -3603,6 +3625,10 @@
.type = HDA_FIXUP_FUNC,
.v.func = alc269_fixup_stereo_dmic,
},
+ [ALC269_FIXUP_HEADSET_MIC] = {
+ .type = HDA_FIXUP_FUNC,
+ .v.func = alc269_fixup_headset_mic,
+ },
[ALC269_FIXUP_QUANTA_MUTE] = {
.type = HDA_FIXUP_FUNC,
.v.func = alc269_fixup_quanta_mute,
@@ -3712,6 +3738,15 @@
.chained = true,
.chain_id = ALC269_FIXUP_HEADSET_MODE_NO_HP_MIC
},
+ [ALC269_FIXUP_DELL3_MIC_NO_PRESENCE] = {
+ .type = HDA_FIXUP_PINS,
+ .v.pins = (const struct hda_pintbl[]) {
+ { 0x1a, 0x01a1913c }, /* use as headset mic, without its own jack detect */
+ { }
+ },
+ .chained = true,
+ .chain_id = ALC269_FIXUP_HEADSET_MODE_NO_HP_MIC
+ },
[ALC269_FIXUP_HEADSET_MODE] = {
.type = HDA_FIXUP_FUNC,
.v.func = alc_fixup_headset_mode,
@@ -3720,6 +3755,15 @@
.type = HDA_FIXUP_FUNC,
.v.func = alc_fixup_headset_mode_no_hp_mic,
},
+ [ALC286_FIXUP_SONY_MIC_NO_PRESENCE] = {
+ .type = HDA_FIXUP_PINS,
+ .v.pins = (const struct hda_pintbl[]) {
+ { 0x18, 0x01a1913c }, /* use as headset mic, without its own jack detect */
+ { }
+ },
+ .chained = true,
+ .chain_id = ALC269_FIXUP_HEADSET_MIC
+ },
[ALC269_FIXUP_ASUS_X101_FUNC] = {
.type = HDA_FIXUP_FUNC,
.v.func = alc269_fixup_x101_headset_mic,
@@ -3804,6 +3848,12 @@
.chained = true,
.chain_id = ALC269_FIXUP_LIMIT_INT_MIC_BOOST
},
+ [ALC290_FIXUP_MONO_SPEAKERS] = {
+ .type = HDA_FIXUP_FUNC,
+ .v.func = alc290_fixup_mono_speakers,
+ .chained = true,
+ .chain_id = ALC269_FIXUP_DELL3_MIC_NO_PRESENCE,
+ },
};
static const struct snd_pci_quirk alc269_fixup_tbl[] = {
@@ -3845,6 +3895,7 @@
SND_PCI_QUIRK(0x1028, 0x0608, "Dell", ALC269_FIXUP_DELL1_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x0609, "Dell", ALC269_FIXUP_DELL1_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x0613, "Dell", ALC269_FIXUP_DELL1_MIC_NO_PRESENCE),
+ SND_PCI_QUIRK(0x1028, 0x0616, "Dell Vostro 5470", ALC290_FIXUP_MONO_SPEAKERS),
SND_PCI_QUIRK(0x1028, 0x15cc, "Dell X5 Precision", ALC269_FIXUP_DELL2_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x15cd, "Dell X5 Precision", ALC269_FIXUP_DELL2_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x103c, 0x1586, "HP", ALC269_FIXUP_HP_MUTE_LED_MIC2),
@@ -3867,6 +3918,7 @@
SND_PCI_QUIRK(0x1043, 0x8398, "ASUS P1005", ALC269_FIXUP_STEREO_DMIC),
SND_PCI_QUIRK(0x1043, 0x83ce, "ASUS P1005", ALC269_FIXUP_STEREO_DMIC),
SND_PCI_QUIRK(0x1043, 0x8516, "ASUS X101CH", ALC269_FIXUP_ASUS_X101),
+ SND_PCI_QUIRK(0x104d, 0x90b6, "Sony VAIO Pro 13", ALC286_FIXUP_SONY_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x104d, 0x9073, "Sony VAIO", ALC275_FIXUP_SONY_VAIO_GPIO2),
SND_PCI_QUIRK(0x104d, 0x907b, "Sony VAIO", ALC275_FIXUP_SONY_HWEQ),
SND_PCI_QUIRK(0x104d, 0x9084, "Sony VAIO", ALC275_FIXUP_SONY_HWEQ),
@@ -3952,6 +4004,7 @@
{.id = ALC269_FIXUP_STEREO_DMIC, .name = "alc269-dmic"},
{.id = ALC271_FIXUP_DMIC, .name = "alc271-dmic"},
{.id = ALC269_FIXUP_INV_DMIC, .name = "inv-dmic"},
+ {.id = ALC269_FIXUP_HEADSET_MIC, .name = "headset-mic"},
{.id = ALC269_FIXUP_LENOVO_DOCK, .name = "lenovo-dock"},
{.id = ALC269_FIXUP_HP_GPIO_LED, .name = "hp-gpio-led"},
{.id = ALC269_FIXUP_DELL1_MIC_NO_PRESENCE, .name = "dell-headset-multi"},
@@ -4569,6 +4622,7 @@
SND_PCI_QUIRK(0x1028, 0x05d8, "Dell", ALC668_FIXUP_DELL_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x05db, "Dell", ALC668_FIXUP_DELL_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x103c, 0x1632, "HP RP5800", ALC662_FIXUP_HP_RP5800),
+ SND_PCI_QUIRK(0x1043, 0x1477, "ASUS N56VZ", ALC662_FIXUP_ASUS_MODE4),
SND_PCI_QUIRK(0x1043, 0x8469, "ASUS mobo", ALC662_FIXUP_NO_JACK_DETECT),
SND_PCI_QUIRK(0x105b, 0x0cd6, "Foxconn", ALC662_FIXUP_ASUS_MODE2),
SND_PCI_QUIRK(0x144d, 0xc051, "Samsung R720", ALC662_FIXUP_IDEAPAD),
diff --git a/sound/usb/usx2y/usbusx2yaudio.c b/sound/usb/usx2y/usbusx2yaudio.c
index 63fb521..6234a51 100644
--- a/sound/usb/usx2y/usbusx2yaudio.c
+++ b/sound/usb/usx2y/usbusx2yaudio.c
@@ -299,19 +299,6 @@
usX2Y_clients_stop(usX2Y);
}
-static void usX2Y_error_sequence(struct usX2Ydev *usX2Y,
- struct snd_usX2Y_substream *subs, struct urb *urb)
-{
- snd_printk(KERN_ERR
-"Sequence Error!(hcd_frame=%i ep=%i%s;wait=%i,frame=%i).\n"
-"Most probably some urb of usb-frame %i is still missing.\n"
-"Cause could be too long delays in usb-hcd interrupt handling.\n",
- usb_get_current_frame_number(usX2Y->dev),
- subs->endpoint, usb_pipein(urb->pipe) ? "in" : "out",
- usX2Y->wait_iso_frame, urb->start_frame, usX2Y->wait_iso_frame);
- usX2Y_clients_stop(usX2Y);
-}
-
static void i_usX2Y_urb_complete(struct urb *urb)
{
struct snd_usX2Y_substream *subs = urb->context;
@@ -328,12 +315,9 @@
usX2Y_error_urb_status(usX2Y, subs, urb);
return;
}
- if (likely((urb->start_frame & 0xFFFF) == (usX2Y->wait_iso_frame & 0xFFFF)))
- subs->completed_urb = urb;
- else {
- usX2Y_error_sequence(usX2Y, subs, urb);
- return;
- }
+
+ subs->completed_urb = urb;
+
{
struct snd_usX2Y_substream *capsubs = usX2Y->subs[SNDRV_PCM_STREAM_CAPTURE],
*playbacksubs = usX2Y->subs[SNDRV_PCM_STREAM_PLAYBACK];
diff --git a/sound/usb/usx2y/usx2yhwdeppcm.c b/sound/usb/usx2y/usx2yhwdeppcm.c
index f2a1acd..814d0e8 100644
--- a/sound/usb/usx2y/usx2yhwdeppcm.c
+++ b/sound/usb/usx2y/usx2yhwdeppcm.c
@@ -244,13 +244,8 @@
usX2Y_error_urb_status(usX2Y, subs, urb);
return;
}
- if (likely((urb->start_frame & 0xFFFF) == (usX2Y->wait_iso_frame & 0xFFFF)))
- subs->completed_urb = urb;
- else {
- usX2Y_error_sequence(usX2Y, subs, urb);
- return;
- }
+ subs->completed_urb = urb;
capsubs = usX2Y->subs[SNDRV_PCM_STREAM_CAPTURE];
capsubs2 = usX2Y->subs[SNDRV_PCM_STREAM_CAPTURE + 2];
playbacksubs = usX2Y->subs[SNDRV_PCM_STREAM_PLAYBACK];
diff --git a/tools/perf/Makefile b/tools/perf/Makefile
index 3a0ff7f..64c043b 100644
--- a/tools/perf/Makefile
+++ b/tools/perf/Makefile
@@ -770,6 +770,7 @@
install-bin: all
$(INSTALL) -d -m 755 '$(DESTDIR_SQ)$(bindir_SQ)'
$(INSTALL) $(OUTPUT)perf '$(DESTDIR_SQ)$(bindir_SQ)'
+ $(INSTALL) -d -m 755 '$(DESTDIR_SQ)$(perfexec_instdir_SQ)'
$(INSTALL) $(OUTPUT)perf-archive -t '$(DESTDIR_SQ)$(perfexec_instdir_SQ)'
ifndef NO_LIBPERL
$(INSTALL) -d -m 755 '$(DESTDIR_SQ)$(perfexec_instdir_SQ)/scripts/perl/Perf-Trace-Util/lib/Perf/Trace'
diff --git a/tools/perf/builtin-stat.c b/tools/perf/builtin-stat.c
index f686d5f..5098f14 100644
--- a/tools/perf/builtin-stat.c
+++ b/tools/perf/builtin-stat.c
@@ -457,6 +457,7 @@
perror("failed to prepare workload");
return -1;
}
+ child_pid = evsel_list->workload.pid;
}
if (group)
diff --git a/tools/perf/config/feature-tests.mak b/tools/perf/config/feature-tests.mak
index d5a8dd4..f793057 100644
--- a/tools/perf/config/feature-tests.mak
+++ b/tools/perf/config/feature-tests.mak
@@ -219,7 +219,7 @@
int main(void)
{
- printf(\"error message: %s\n\", audit_errno_to_name(0));
+ printf(\"error message: %s\", audit_errno_to_name(0));
return audit_open();
}
endef
diff --git a/tools/perf/util/dwarf-aux.c b/tools/perf/util/dwarf-aux.c
index e23bde1..7defd77 100644
--- a/tools/perf/util/dwarf-aux.c
+++ b/tools/perf/util/dwarf-aux.c
@@ -426,7 +426,7 @@
* @die_mem: a buffer for result DIE
*
* Search a non-inlined function DIE which includes @addr. Stores the
- * DIE to @die_mem and returns it if found. Returns NULl if failed.
+ * DIE to @die_mem and returns it if found. Returns NULL if failed.
*/
Dwarf_Die *die_find_realfunc(Dwarf_Die *cu_die, Dwarf_Addr addr,
Dwarf_Die *die_mem)
@@ -454,15 +454,32 @@
}
/**
- * die_find_inlinefunc - Search an inlined function at given address
- * @cu_die: a CU DIE which including @addr
+ * die_find_top_inlinefunc - Search the top inlined function at given address
+ * @sp_die: a subprogram DIE which including @addr
* @addr: target address
* @die_mem: a buffer for result DIE
*
* Search an inlined function DIE which includes @addr. Stores the
- * DIE to @die_mem and returns it if found. Returns NULl if failed.
+ * DIE to @die_mem and returns it if found. Returns NULL if failed.
+ * Even if several inlined functions are expanded recursively, this
+ * doesn't trace it down, and returns the topmost one.
+ */
+Dwarf_Die *die_find_top_inlinefunc(Dwarf_Die *sp_die, Dwarf_Addr addr,
+ Dwarf_Die *die_mem)
+{
+ return die_find_child(sp_die, __die_find_inline_cb, &addr, die_mem);
+}
+
+/**
+ * die_find_inlinefunc - Search an inlined function at given address
+ * @sp_die: a subprogram DIE which including @addr
+ * @addr: target address
+ * @die_mem: a buffer for result DIE
+ *
+ * Search an inlined function DIE which includes @addr. Stores the
+ * DIE to @die_mem and returns it if found. Returns NULL if failed.
* If several inlined functions are expanded recursively, this trace
- * it and returns deepest one.
+ * it down and returns deepest one.
*/
Dwarf_Die *die_find_inlinefunc(Dwarf_Die *sp_die, Dwarf_Addr addr,
Dwarf_Die *die_mem)
diff --git a/tools/perf/util/dwarf-aux.h b/tools/perf/util/dwarf-aux.h
index 8658d41..b4fe90c 100644
--- a/tools/perf/util/dwarf-aux.h
+++ b/tools/perf/util/dwarf-aux.h
@@ -79,7 +79,11 @@
extern Dwarf_Die *die_find_realfunc(Dwarf_Die *cu_die, Dwarf_Addr addr,
Dwarf_Die *die_mem);
-/* Search an inlined function including given address */
+/* Search the top inlined function including given address */
+extern Dwarf_Die *die_find_top_inlinefunc(Dwarf_Die *sp_die, Dwarf_Addr addr,
+ Dwarf_Die *die_mem);
+
+/* Search the deepest inlined function including given address */
extern Dwarf_Die *die_find_inlinefunc(Dwarf_Die *sp_die, Dwarf_Addr addr,
Dwarf_Die *die_mem);
diff --git a/tools/perf/util/header.c b/tools/perf/util/header.c
index ce69901..c3e5a3b 100644
--- a/tools/perf/util/header.c
+++ b/tools/perf/util/header.c
@@ -2768,6 +2768,18 @@
if (perf_file_header__read(&f_header, header, fd) < 0)
return -EINVAL;
+ /*
+ * Sanity check that perf.data was written cleanly; data size is
+ * initialized to 0 and updated only if the on_exit function is run.
+ * If data size is still 0 then the file contains only partial
+ * information. Just warn user and process it as much as it can.
+ */
+ if (f_header.data.size == 0) {
+ pr_warning("WARNING: The %s file's data size field is 0 which is unexpected.\n"
+ "Was the 'perf record' command properly terminated?\n",
+ session->filename);
+ }
+
nr_attrs = f_header.attrs.size / f_header.attr_size;
lseek(fd, f_header.attrs.offset, SEEK_SET);
diff --git a/tools/perf/util/probe-finder.c b/tools/perf/util/probe-finder.c
index 371476c..c09e0a9 100644
--- a/tools/perf/util/probe-finder.c
+++ b/tools/perf/util/probe-finder.c
@@ -1327,8 +1327,8 @@
struct perf_probe_point *ppt)
{
Dwarf_Die cudie, spdie, indie;
- Dwarf_Addr _addr, baseaddr;
- const char *fname = NULL, *func = NULL, *tmp;
+ Dwarf_Addr _addr = 0, baseaddr = 0;
+ const char *fname = NULL, *func = NULL, *basefunc = NULL, *tmp;
int baseline = 0, lineno = 0, ret = 0;
/* Adjust address with bias */
@@ -1349,27 +1349,36 @@
/* Find a corresponding function (name, baseline and baseaddr) */
if (die_find_realfunc(&cudie, (Dwarf_Addr)addr, &spdie)) {
/* Get function entry information */
- tmp = dwarf_diename(&spdie);
- if (!tmp ||
+ func = basefunc = dwarf_diename(&spdie);
+ if (!func ||
dwarf_entrypc(&spdie, &baseaddr) != 0 ||
- dwarf_decl_line(&spdie, &baseline) != 0)
+ dwarf_decl_line(&spdie, &baseline) != 0) {
+ lineno = 0;
goto post;
- func = tmp;
+ }
- if (addr == (unsigned long)baseaddr)
+ if (addr == (unsigned long)baseaddr) {
/* Function entry - Relative line number is 0 */
lineno = baseline;
- else if (die_find_inlinefunc(&spdie, (Dwarf_Addr)addr,
- &indie)) {
+ fname = dwarf_decl_file(&spdie);
+ goto post;
+ }
+
+ /* Track down the inline functions step by step */
+ while (die_find_top_inlinefunc(&spdie, (Dwarf_Addr)addr,
+ &indie)) {
+ /* There is an inline function */
if (dwarf_entrypc(&indie, &_addr) == 0 &&
- _addr == addr)
+ _addr == addr) {
/*
* addr is at an inline function entry.
* In this case, lineno should be the call-site
- * line number.
+ * line number. (overwrite lineinfo)
*/
lineno = die_get_call_lineno(&indie);
- else {
+ fname = die_get_call_file(&indie);
+ break;
+ } else {
/*
* addr is in an inline function body.
* Since lineno points one of the lines
@@ -1377,19 +1386,27 @@
* be the entry line of the inline function.
*/
tmp = dwarf_diename(&indie);
- if (tmp &&
- dwarf_decl_line(&spdie, &baseline) == 0)
- func = tmp;
+ if (!tmp ||
+ dwarf_decl_line(&indie, &baseline) != 0)
+ break;
+ func = tmp;
+ spdie = indie;
}
}
+ /* Verify the lineno and baseline are in a same file */
+ tmp = dwarf_decl_file(&spdie);
+ if (!tmp || strcmp(tmp, fname) != 0)
+ lineno = 0;
}
post:
/* Make a relative line number or an offset */
if (lineno)
ppt->line = lineno - baseline;
- else if (func)
+ else if (basefunc) {
ppt->offset = addr - (unsigned long)baseaddr;
+ func = basefunc;
+ }
/* Duplicate strings */
if (func) {
diff --git a/tools/perf/util/session.c b/tools/perf/util/session.c
index 70ffa41..568b750 100644
--- a/tools/perf/util/session.c
+++ b/tools/perf/util/session.c
@@ -256,6 +256,8 @@
tool->sample = process_event_sample_stub;
if (tool->mmap == NULL)
tool->mmap = process_event_stub;
+ if (tool->mmap2 == NULL)
+ tool->mmap2 = process_event_stub;
if (tool->comm == NULL)
tool->comm = process_event_stub;
if (tool->fork == NULL)
@@ -1310,7 +1312,7 @@
file_offset = page_offset;
head = data_offset - page_offset;
- if (data_offset + data_size < file_size)
+ if (data_size && (data_offset + data_size < file_size))
file_size = data_offset + data_size;
progress_next = file_size / 16;