m68knommu: platform setup for 532x ColdFire parts
Switch to platform style configuration for 532x ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/arch/m68knommu/platform/532x/config.c b/arch/m68knommu/platform/532x/config.c
index f77328b..758bc7a 100644
--- a/arch/m68knommu/platform/532x/config.c
+++ b/arch/m68knommu/platform/532x/config.c
@@ -21,10 +21,11 @@
#include <linux/param.h>
#include <linux/init.h>
#include <linux/interrupt.h>
-#include <asm/dma.h>
+#include <linux/io.h>
#include <asm/machdep.h>
#include <asm/coldfire.h>
#include <asm/mcfsim.h>
+#include <asm/mcfuart.h>
#include <asm/mcfdma.h>
#include <asm/mcfwdebug.h>
@@ -38,11 +39,60 @@
/***************************************************************************/
-/*
- * DMA channel base address table.
- */
-unsigned int dma_base_addr[MAX_M68K_DMA_CHANNELS] = { };
-unsigned int dma_device_address[MAX_M68K_DMA_CHANNELS];
+static struct mcf_platform_uart m532x_uart_platform[] = {
+ {
+ .mapbase = MCF_MBAR + MCFUART_BASE1,
+ .irq = MCFINT_VECBASE + MCFINT_UART0,
+ },
+ {
+ .mapbase = MCF_MBAR + MCFUART_BASE2,
+ .irq = MCFINT_VECBASE + MCFINT_UART1,
+ },
+ {
+ .mapbase = MCF_MBAR + MCFUART_BASE3,
+ .irq = MCFINT_VECBASE + MCFINT_UART2,
+ },
+ { },
+};
+
+static struct platform_device m532x_uart = {
+ .name = "mcfuart",
+ .id = 0,
+ .dev.platform_data = m532x_uart_platform,
+};
+
+static struct platform_device *m532x_devices[] __initdata = {
+ &m532x_uart,
+};
+
+/***************************************************************************/
+
+static void __init m532x_uart_init_line(int line, int irq)
+{
+ if (line == 0) {
+ MCF_INTC0_ICR26 = 0x3;
+ MCF_INTC0_CIMR = 26;
+ /* GPIO initialization */
+ MCF_GPIO_PAR_UART |= 0x000F;
+ } else if (line == 1) {
+ MCF_INTC0_ICR27 = 0x3;
+ MCF_INTC0_CIMR = 27;
+ /* GPIO initialization */
+ MCF_GPIO_PAR_UART |= 0x0FF0;
+ } else if (line == 2) {
+ MCF_INTC0_ICR28 = 0x3;
+ MCF_INTC0_CIMR = 28;
+ }
+}
+
+static void __init m532x_uarts_init(void)
+{
+ const int nrlines = ARRAY_SIZE(m532x_uart_platform);
+ int line;
+
+ for (line = 0; (line < nrlines); line++)
+ m532x_uart_init_line(line, m532x_uart_platform[line].irq);
+}
/***************************************************************************/
@@ -80,7 +130,7 @@
/***************************************************************************/
-void config_BSP(char *commandp, int size)
+void __init config_BSP(char *commandp, int size)
{
mcf_setimr(MCFSIM_IMR_MASKALL);
@@ -99,7 +149,7 @@
mcf_profilevector = 64+33;
mach_reset = coldfire_reset;
-#ifdef MCF_BDM_DISABLE
+#ifdef CONFIG_BDM_DISABLE
/*
* Disable the BDM clocking. This also turns off most of the rest of
* the BDM device. This is good for EMC reasons. This option is not
@@ -110,9 +160,19 @@
}
/***************************************************************************/
-/* Board initialization */
-/********************************************************************/
+static int __init init_BSP(void)
+{
+ m532x_uarts_init();
+ platform_add_devices(m532x_devices, ARRAY_SIZE(m532x_devices));
+ return 0;
+}
+
+arch_initcall(init_BSP);
+
+/***************************************************************************/
+/* Board initialization */
+/***************************************************************************/
/*
* PLL min/max specifications
*/