| # |
| # SATA/PATA driver configuration |
| # |
| |
| menuconfig ATA |
| tristate "Serial ATA (prod) and Parallel ATA (experimental) drivers" |
| depends on HAS_IOMEM |
| depends on BLOCK |
| depends on !(M32R || M68K) || BROKEN |
| select SCSI |
| ---help--- |
| If you want to use a ATA hard disk, ATA tape drive, ATA CD-ROM or |
| any other ATA device under Linux, say Y and make sure that you know |
| the name of your ATA host adapter (the card inside your computer |
| that "speaks" the ATA protocol, also called ATA controller), |
| because you will be asked for it. |
| |
| NOTE: ATA enables basic SCSI support; *however*, |
| 'SCSI disk support', 'SCSI tape support', or |
| 'SCSI CDROM support' may also be needed, |
| depending on your hardware configuration. |
| |
| if ATA |
| |
| config ATA_NONSTANDARD |
| bool |
| default n |
| |
| config ATA_ACPI |
| bool "ATA ACPI Support" |
| depends on ACPI && PCI |
| select ACPI_DOCK |
| default y |
| help |
| This option adds support for ATA-related ACPI objects. |
| These ACPI objects add the ability to retrieve taskfiles |
| from the ACPI BIOS and write them to the disk controller. |
| These objects may be related to performance, security, |
| power management, or other areas. |
| You can disable this at kernel boot time by using the |
| option libata.noacpi=1 |
| |
| config SATA_PMP |
| bool "SATA Port Multiplier support" |
| default y |
| help |
| This option adds support for SATA Port Multipliers |
| (the SATA version of an ethernet hub, or SAS expander). |
| |
| config SATA_AHCI |
| tristate "AHCI SATA support" |
| depends on PCI |
| help |
| This option enables support for AHCI Serial ATA. |
| |
| If unsure, say N. |
| |
| config SATA_SIL24 |
| tristate "Silicon Image 3124/3132 SATA support" |
| depends on PCI |
| help |
| This option enables support for Silicon Image 3124/3132 Serial ATA. |
| |
| If unsure, say N. |
| |
| config SATA_FSL |
| tristate "Freescale 3.0Gbps SATA support" |
| depends on FSL_SOC |
| help |
| This option enables support for Freescale 3.0Gbps SATA controller. |
| It can be found on MPC837x and MPC8315. |
| |
| If unsure, say N. |
| |
| config ATA_SFF |
| bool "ATA SFF support" |
| default y |
| help |
| This option adds support for ATA controllers with SFF |
| compliant or similar programming interface. |
| |
| SFF is the legacy IDE interface that has been around since |
| the dawn of time. Almost all PATA controllers have an |
| SFF interface. Many SATA controllers have an SFF interface |
| when configured into a legacy compatibility mode. |
| |
| For users with exclusively modern controllers like AHCI, |
| Silicon Image 3124, or Marvell 6440, you may choose to |
| disable this unneeded SFF support. |
| |
| If unsure, say Y. |
| |
| if ATA_SFF |
| |
| config SATA_SVW |
| tristate "ServerWorks Frodo / Apple K2 SATA support" |
| depends on PCI |
| help |
| This option enables support for Broadcom/Serverworks/Apple K2 |
| SATA support. |
| |
| If unsure, say N. |
| |
| config ATA_PIIX |
| tristate "Intel ESB, ICH, PIIX3, PIIX4 PATA/SATA support" |
| depends on PCI |
| help |
| This option enables support for ICH5/6/7/8 Serial ATA |
| and support for PATA on the Intel ESB/ICH/PIIX3/PIIX4 series |
| host controllers. |
| |
| If unsure, say N. |
| |
| config SATA_MV |
| tristate "Marvell SATA support" |
| help |
| This option enables support for the Marvell Serial ATA family. |
| Currently supports 88SX[56]0[48][01] PCI(-X) chips, |
| as well as the newer [67]042 PCI-X/PCIe and SOC devices. |
| |
| If unsure, say N. |
| |
| config SATA_NV |
| tristate "NVIDIA SATA support" |
| depends on PCI |
| help |
| This option enables support for NVIDIA Serial ATA. |
| |
| If unsure, say N. |
| |
| config PDC_ADMA |
| tristate "Pacific Digital ADMA support" |
| depends on PCI |
| help |
| This option enables support for Pacific Digital ADMA controllers |
| |
| If unsure, say N. |
| |
| config SATA_QSTOR |
| tristate "Pacific Digital SATA QStor support" |
| depends on PCI |
| help |
| This option enables support for Pacific Digital Serial ATA QStor. |
| |
| If unsure, say N. |
| |
| config SATA_PROMISE |
| tristate "Promise SATA TX2/TX4 support" |
| depends on PCI |
| help |
| This option enables support for Promise Serial ATA TX2/TX4. |
| |
| If unsure, say N. |
| |
| config SATA_SX4 |
| tristate "Promise SATA SX4 support (Experimental)" |
| depends on PCI && EXPERIMENTAL |
| help |
| This option enables support for Promise Serial ATA SX4. |
| |
| If unsure, say N. |
| |
| config SATA_SIL |
| tristate "Silicon Image SATA support" |
| depends on PCI |
| help |
| This option enables support for Silicon Image Serial ATA. |
| |
| If unsure, say N. |
| |
| config SATA_SIS |
| tristate "SiS 964/965/966/180 SATA support" |
| depends on PCI |
| select PATA_SIS |
| help |
| This option enables support for SiS Serial ATA on |
| SiS 964/965/966/180 and Parallel ATA on SiS 180. |
| The PATA support for SiS 180 requires additionally to |
| enable the PATA_SIS driver in the config. |
| If unsure, say N. |
| |
| config SATA_ULI |
| tristate "ULi Electronics SATA support" |
| depends on PCI |
| help |
| This option enables support for ULi Electronics SATA. |
| |
| If unsure, say N. |
| |
| config SATA_VIA |
| tristate "VIA SATA support" |
| depends on PCI |
| help |
| This option enables support for VIA Serial ATA. |
| |
| If unsure, say N. |
| |
| config SATA_VITESSE |
| tristate "VITESSE VSC-7174 / INTEL 31244 SATA support" |
| depends on PCI |
| help |
| This option enables support for Vitesse VSC7174 and Intel 31244 Serial ATA. |
| |
| If unsure, say N. |
| |
| config SATA_INIC162X |
| tristate "Initio 162x SATA support" |
| depends on PCI |
| help |
| This option enables support for Initio 162x Serial ATA. |
| |
| config PATA_ACPI |
| tristate "ACPI firmware driver for PATA" |
| depends on ATA_ACPI |
| help |
| This option enables an ACPI method driver which drives |
| motherboard PATA controller interfaces through the ACPI |
| firmware in the BIOS. This driver can sometimes handle |
| otherwise unsupported hardware. |
| |
| config PATA_ALI |
| tristate "ALi PATA support" |
| depends on PCI |
| help |
| This option enables support for the ALi ATA interfaces |
| found on the many ALi chipsets. |
| |
| If unsure, say N. |
| |
| config PATA_AMD |
| tristate "AMD/NVidia PATA support" |
| depends on PCI |
| help |
| This option enables support for the AMD and NVidia PATA |
| interfaces found on the chipsets for Athlon/Athlon64. |
| |
| If unsure, say N. |
| |
| config PATA_ARTOP |
| tristate "ARTOP 6210/6260 PATA support" |
| depends on PCI |
| help |
| This option enables support for ARTOP PATA controllers. |
| |
| If unsure, say N. |
| |
| config PATA_AT32 |
| tristate "Atmel AVR32 PATA support (Experimental)" |
| depends on AVR32 && PLATFORM_AT32AP && EXPERIMENTAL |
| help |
| This option enables support for the IDE devices on the |
| Atmel AT32AP platform. |
| |
| If unsure, say N. |
| |
| config PATA_ATIIXP |
| tristate "ATI PATA support" |
| depends on PCI |
| help |
| This option enables support for the ATI ATA interfaces |
| found on the many ATI chipsets. |
| |
| If unsure, say N. |
| |
| config PATA_CMD640_PCI |
| tristate "CMD640 PCI PATA support (Experimental)" |
| depends on PCI && EXPERIMENTAL |
| help |
| This option enables support for the CMD640 PCI IDE |
| interface chip. Only the primary channel is currently |
| supported. |
| |
| If unsure, say N. |
| |
| config PATA_CMD64X |
| tristate "CMD64x PATA support" |
| depends on PCI |
| help |
| This option enables support for the CMD64x series chips |
| except for the CMD640. |
| |
| If unsure, say N. |
| |
| config PATA_CS5520 |
| tristate "CS5510/5520 PATA support" |
| depends on PCI |
| help |
| This option enables support for the Cyrix 5510/5520 |
| companion chip used with the MediaGX/Geode processor family. |
| |
| If unsure, say N. |
| |
| config PATA_CS5530 |
| tristate "CS5530 PATA support" |
| depends on PCI |
| help |
| This option enables support for the Cyrix/NatSemi/AMD CS5530 |
| companion chip used with the MediaGX/Geode processor family. |
| |
| If unsure, say N. |
| |
| config PATA_CS5535 |
| tristate "CS5535 PATA support (Experimental)" |
| depends on PCI && X86 && !X86_64 && EXPERIMENTAL |
| help |
| This option enables support for the NatSemi/AMD CS5535 |
| companion chip used with the Geode processor family. |
| |
| If unsure, say N. |
| |
| config PATA_CS5536 |
| tristate "CS5536 PATA support" |
| depends on PCI && X86 && !X86_64 |
| help |
| This option enables support for the AMD CS5536 |
| companion chip used with the Geode LX processor family. |
| |
| If unsure, say N. |
| |
| config PATA_CYPRESS |
| tristate "Cypress CY82C693 PATA support (Very Experimental)" |
| depends on PCI && EXPERIMENTAL |
| help |
| This option enables support for the Cypress/Contaq CY82C693 |
| chipset found in some Alpha systems |
| |
| If unsure, say N. |
| |
| config PATA_EFAR |
| tristate "EFAR SLC90E66 support" |
| depends on PCI |
| help |
| This option enables support for the EFAR SLC90E66 |
| IDE controller found on some older machines. |
| |
| If unsure, say N. |
| |
| config ATA_GENERIC |
| tristate "Generic ATA support" |
| depends on PCI |
| help |
| This option enables support for generic BIOS configured |
| ATA controllers via the new ATA layer |
| |
| If unsure, say N. |
| |
| config PATA_HPT366 |
| tristate "HPT 366/368 PATA support" |
| depends on PCI |
| help |
| This option enables support for the HPT 366 and 368 |
| PATA controllers via the new ATA layer. |
| |
| If unsure, say N. |
| |
| config PATA_HPT37X |
| tristate "HPT 370/370A/371/372/374/302 PATA support (Experimental)" |
| depends on PCI && EXPERIMENTAL |
| help |
| This option enables support for the majority of the later HPT |
| PATA controllers via the new ATA layer. |
| |
| If unsure, say N. |
| |
| config PATA_HPT3X2N |
| tristate "HPT 372N/302N PATA support (Experimental)" |
| depends on PCI && EXPERIMENTAL |
| help |
| This option enables support for the N variant HPT PATA |
| controllers via the new ATA layer |
| |
| If unsure, say N. |
| |
| config PATA_HPT3X3 |
| tristate "HPT 343/363 PATA support" |
| depends on PCI |
| help |
| This option enables support for the HPT 343/363 |
| PATA controllers via the new ATA layer |
| |
| If unsure, say N. |
| |
| config PATA_HPT3X3_DMA |
| bool "HPT 343/363 DMA support (Experimental)" |
| depends on PATA_HPT3X3 |
| help |
| This option enables DMA support for the HPT343/363 |
| controllers. Enable with care as there are still some |
| problems with DMA on this chipset. |
| |
| config PATA_ISAPNP |
| tristate "ISA Plug and Play PATA support" |
| depends on ISAPNP |
| help |
| This option enables support for ISA plug & play ATA |
| controllers such as those found on old soundcards. |
| |
| If unsure, say N. |
| |
| config PATA_IT821X |
| tristate "IT8211/2 PATA support" |
| depends on PCI |
| help |
| This option enables support for the ITE 8211 and 8212 |
| PATA controllers via the new ATA layer, including RAID |
| mode. |
| |
| If unsure, say N. |
| |
| config PATA_IT8213 |
| tristate "IT8213 PATA support (Experimental)" |
| depends on PCI && EXPERIMENTAL |
| help |
| This option enables support for the ITE 821 PATA |
| controllers via the new ATA layer. |
| |
| If unsure, say N. |
| |
| config PATA_JMICRON |
| tristate "JMicron PATA support" |
| depends on PCI |
| help |
| Enable support for the JMicron IDE controller, via the new |
| ATA layer. |
| |
| If unsure, say N. |
| |
| config PATA_LEGACY |
| tristate "Legacy ISA PATA support (Experimental)" |
| depends on ISA && EXPERIMENTAL |
| help |
| This option enables support for ISA/VLB bus legacy PATA |
| ports and allows them to be accessed via the new ATA layer. |
| |
| If unsure, say N. |
| |
| config PATA_TRIFLEX |
| tristate "Compaq Triflex PATA support" |
| depends on PCI |
| help |
| Enable support for the Compaq 'Triflex' IDE controller as found |
| on many Compaq Pentium-Pro systems, via the new ATA layer. |
| |
| If unsure, say N. |
| |
| config PATA_MARVELL |
| tristate "Marvell PATA support via legacy mode" |
| depends on PCI |
| help |
| This option enables limited support for the Marvell 88SE61xx ATA |
| controllers. If you wish to use only the SATA ports then select |
| the AHCI driver alone. If you wish to the use the PATA port or |
| both SATA and PATA include this driver. |
| |
| If unsure, say N. |
| |
| config PATA_MPC52xx |
| tristate "Freescale MPC52xx SoC internal IDE" |
| depends on PPC_MPC52xx && PPC_BESTCOMM |
| select PPC_BESTCOMM_ATA |
| help |
| This option enables support for integrated IDE controller |
| of the Freescale MPC52xx SoC. |
| |
| If unsure, say N. |
| |
| config PATA_MPIIX |
| tristate "Intel PATA MPIIX support" |
| depends on PCI |
| help |
| This option enables support for MPIIX PATA support. |
| |
| If unsure, say N. |
| |
| config PATA_OLDPIIX |
| tristate "Intel PATA old PIIX support" |
| depends on PCI |
| help |
| This option enables support for early PIIX PATA support. |
| |
| If unsure, say N. |
| |
| config PATA_NETCELL |
| tristate "NETCELL Revolution RAID support" |
| depends on PCI |
| help |
| This option enables support for the Netcell Revolution RAID |
| PATA controller. |
| |
| If unsure, say N. |
| |
| config PATA_NINJA32 |
| tristate "Ninja32/Delkin Cardbus ATA support (Experimental)" |
| depends on PCI && EXPERIMENTAL |
| help |
| This option enables support for the Ninja32, Delkin and |
| possibly other brands of Cardbus ATA adapter |
| |
| If unsure, say N. |
| |
| config PATA_NS87410 |
| tristate "Nat Semi NS87410 PATA support" |
| depends on PCI |
| help |
| This option enables support for the National Semiconductor |
| NS87410 PCI-IDE controller. |
| |
| If unsure, say N. |
| |
| config PATA_NS87415 |
| tristate "Nat Semi NS87415 PATA support" |
| depends on PCI |
| help |
| This option enables support for the National Semiconductor |
| NS87415 PCI-IDE controller. |
| |
| If unsure, say N. |
| |
| config PATA_OPTI |
| tristate "OPTI621/6215 PATA support (Very Experimental)" |
| depends on PCI && EXPERIMENTAL |
| help |
| This option enables full PIO support for the early Opti ATA |
| controllers found on some old motherboards. |
| |
| If unsure, say N. |
| |
| config PATA_OPTIDMA |
| tristate "OPTI FireStar PATA support (Very Experimental)" |
| depends on PCI && EXPERIMENTAL |
| help |
| This option enables DMA/PIO support for the later OPTi |
| controllers found on some old motherboards and in some |
| laptops. |
| |
| If unsure, say N. |
| |
| config PATA_PALMLD |
| tristate "Palm LifeDrive PATA support" |
| depends on MACH_PALMLD |
| help |
| This option enables support for Palm LifeDrive's internal ATA |
| port via the new ATA layer. |
| |
| If unsure, say N. |
| |
| config PATA_PCMCIA |
| tristate "PCMCIA PATA support" |
| depends on PCMCIA |
| help |
| This option enables support for PCMCIA ATA interfaces, including |
| compact flash card adapters via the new ATA layer. |
| |
| If unsure, say N. |
| |
| config PATA_PDC_OLD |
| tristate "Older Promise PATA controller support" |
| depends on PCI |
| help |
| This option enables support for the Promise 20246, 20262, 20263, |
| 20265 and 20267 adapters. |
| |
| If unsure, say N. |
| |
| config PATA_QDI |
| tristate "QDI VLB PATA support" |
| depends on ISA |
| help |
| Support for QDI 6500 and 6580 PATA controllers on VESA local bus. |
| |
| config PATA_RADISYS |
| tristate "RADISYS 82600 PATA support (Experimental)" |
| depends on PCI && EXPERIMENTAL |
| help |
| This option enables support for the RADISYS 82600 |
| PATA controllers via the new ATA layer |
| |
| If unsure, say N. |
| |
| config PATA_RB532 |
| tristate "RouterBoard 532 PATA CompactFlash support" |
| depends on MIKROTIK_RB532 |
| help |
| This option enables support for the RouterBoard 532 |
| PATA CompactFlash controller. |
| |
| If unsure, say N. |
| |
| config PATA_RZ1000 |
| tristate "PC Tech RZ1000 PATA support" |
| depends on PCI |
| help |
| This option enables basic support for the PC Tech RZ1000/1 |
| PATA controllers via the new ATA layer |
| |
| If unsure, say N. |
| |
| config PATA_SC1200 |
| tristate "SC1200 PATA support" |
| depends on PCI |
| help |
| This option enables support for the NatSemi/AMD SC1200 SoC |
| companion chip used with the Geode processor family. |
| |
| If unsure, say N. |
| |
| config PATA_SERVERWORKS |
| tristate "SERVERWORKS OSB4/CSB5/CSB6/HT1000 PATA support" |
| depends on PCI |
| help |
| This option enables support for the Serverworks OSB4/CSB5/CSB6 and |
| HT1000 PATA controllers, via the new ATA layer. |
| |
| If unsure, say N. |
| |
| config PATA_PDC2027X |
| tristate "Promise PATA 2027x support" |
| depends on PCI |
| help |
| This option enables support for Promise PATA pdc20268 to pdc20277 host adapters. |
| |
| If unsure, say N. |
| |
| config PATA_SIL680 |
| tristate "CMD / Silicon Image 680 PATA support" |
| depends on PCI |
| help |
| This option enables support for CMD / Silicon Image 680 PATA. |
| |
| If unsure, say N. |
| |
| config PATA_SIS |
| tristate "SiS PATA support" |
| depends on PCI |
| help |
| This option enables support for SiS PATA controllers |
| |
| If unsure, say N. |
| |
| config PATA_VIA |
| tristate "VIA PATA support" |
| depends on PCI |
| help |
| This option enables support for the VIA PATA interfaces |
| found on the many VIA chipsets. |
| |
| If unsure, say N. |
| |
| config PATA_WINBOND |
| tristate "Winbond SL82C105 PATA support" |
| depends on PCI |
| help |
| This option enables support for SL82C105 PATA devices found in the |
| Netwinder and some other systems |
| |
| If unsure, say N. |
| |
| config PATA_WINBOND_VLB |
| tristate "Winbond W83759A VLB PATA support (Experimental)" |
| depends on ISA && EXPERIMENTAL |
| help |
| Support for the Winbond W83759A controller on Vesa Local Bus |
| systems. |
| |
| config HAVE_PATA_PLATFORM |
| bool |
| help |
| This is an internal configuration node for any machine that |
| uses pata-platform driver to enable the relevant driver in the |
| configuration structure without having to submit endless patches |
| to update the PATA_PLATFORM entry. |
| |
| config PATA_PLATFORM |
| tristate "Generic platform device PATA support" |
| depends on EMBEDDED || PPC || HAVE_PATA_PLATFORM |
| help |
| This option enables support for generic directly connected ATA |
| devices commonly found on embedded systems. |
| |
| If unsure, say N. |
| |
| config PATA_AT91 |
| tristate "PATA support for AT91SAM9260" |
| depends on ARM && ARCH_AT91 |
| help |
| This option enables support for IDE devices on the Atmel AT91SAM9260 SoC. |
| |
| If unsure, say N. |
| |
| config PATA_OF_PLATFORM |
| tristate "OpenFirmware platform device PATA support" |
| depends on PATA_PLATFORM && PPC_OF |
| help |
| This option enables support for generic directly connected ATA |
| devices commonly found on embedded systems with OpenFirmware |
| bindings. |
| |
| If unsure, say N. |
| |
| config PATA_ICSIDE |
| tristate "Acorn ICS PATA support" |
| depends on ARM && ARCH_ACORN |
| help |
| On Acorn systems, say Y here if you wish to use the ICS PATA |
| interface card. This is not required for ICS partition support. |
| If you are unsure, say N to this. |
| |
| config PATA_IXP4XX_CF |
| tristate "IXP4XX Compact Flash support" |
| depends on ARCH_IXP4XX |
| help |
| This option enables support for a Compact Flash connected on |
| the ixp4xx expansion bus. This driver had been written for |
| Loft/Avila boards in mind but can work with others. |
| |
| If unsure, say N. |
| |
| config PATA_OCTEON_CF |
| tristate "OCTEON Boot Bus Compact Flash support" |
| depends on CPU_CAVIUM_OCTEON |
| help |
| This option enables a polled compact flash driver for use with |
| compact flash cards attached to the OCTEON boot bus. |
| |
| If unsure, say N. |
| |
| config PATA_SCC |
| tristate "Toshiba's Cell Reference Set IDE support" |
| depends on PCI && PPC_CELLEB |
| help |
| This option enables support for the built-in IDE controller on |
| Toshiba Cell Reference Board. |
| |
| If unsure, say N. |
| |
| config PATA_SCH |
| tristate "Intel SCH PATA support" |
| depends on PCI |
| help |
| This option enables support for Intel SCH PATA on the Intel |
| SCH (US15W, US15L, UL11L) series host controllers. |
| |
| If unsure, say N. |
| |
| config PATA_BF54X |
| tristate "Blackfin 54x ATAPI support" |
| depends on BF542 || BF548 || BF549 |
| help |
| This option enables support for the built-in ATAPI controller on |
| Blackfin 54x family chips. |
| |
| If unsure, say N. |
| |
| endif # ATA_SFF |
| endif # ATA |