| /* |
| * linux/drivers/char/cd1865.h -- Definitions relating to the CD1865 |
| * for the Specialix IO8+ multiport serial driver. |
| * |
| * Copyright (C) 1997 Roger Wolff (R.E.Wolff@BitWizard.nl) |
| * Copyright (C) 1994-1996 Dmitry Gorodchanin (pgmdsg@ibi.com) |
| * |
| * Specialix pays for the development and support of this driver. |
| * Please DO contact io8-linux@specialix.co.uk if you require |
| * support. |
| * |
| * This driver was developped in the BitWizard linux device |
| * driver service. If you require a linux device driver for your |
| * product, please contact devices@BitWizard.nl for a quote. |
| * |
| */ |
| |
| /* |
| * Definitions for Driving CD180/CD1864/CD1865 based eightport serial cards. |
| */ |
| |
| |
| /* Values of choice for Interrupt ACKs */ |
| /* These values are "obligatory" if you use the register based |
| * interrupt acknowledgements. See page 99-101 of V2.0 of the CD1865 |
| * databook */ |
| #define SX_ACK_MINT 0x75 /* goes to PILR1 */ |
| #define SX_ACK_TINT 0x76 /* goes to PILR2 */ |
| #define SX_ACK_RINT 0x77 /* goes to PILR3 */ |
| |
| /* Chip ID (is used when chips ar daisy chained.) */ |
| #define SX_ID 0x10 |
| |
| /* Definitions for Cirrus Logic CL-CD186x 8-port async mux chip */ |
| |
| #define CD186x_NCH 8 /* Total number of channels */ |
| #define CD186x_TPC 16 /* Ticks per character */ |
| #define CD186x_NFIFO 8 /* TX FIFO size */ |
| |
| |
| /* Global registers */ |
| |
| #define CD186x_GIVR 0x40 /* Global Interrupt Vector Register */ |
| #define CD186x_GICR 0x41 /* Global Interrupting Channel Register */ |
| #define CD186x_PILR1 0x61 /* Priority Interrupt Level Register 1 */ |
| #define CD186x_PILR2 0x62 /* Priority Interrupt Level Register 2 */ |
| #define CD186x_PILR3 0x63 /* Priority Interrupt Level Register 3 */ |
| #define CD186x_CAR 0x64 /* Channel Access Register */ |
| #define CD186x_SRSR 0x65 /* Channel Access Register */ |
| #define CD186x_GFRCR 0x6b /* Global Firmware Revision Code Register */ |
| #define CD186x_PPRH 0x70 /* Prescaler Period Register High */ |
| #define CD186x_PPRL 0x71 /* Prescaler Period Register Low */ |
| #define CD186x_RDR 0x78 /* Receiver Data Register */ |
| #define CD186x_RCSR 0x7a /* Receiver Character Status Register */ |
| #define CD186x_TDR 0x7b /* Transmit Data Register */ |
| #define CD186x_EOIR 0x7f /* End of Interrupt Register */ |
| #define CD186x_MRAR 0x75 /* Modem Request Acknowledge register */ |
| #define CD186x_TRAR 0x76 /* Transmit Request Acknowledge register */ |
| #define CD186x_RRAR 0x77 /* Receive Request Acknowledge register */ |
| #define CD186x_SRCR 0x66 /* Service Request Configuration register */ |
| |
| /* Channel Registers */ |
| |
| #define CD186x_CCR 0x01 /* Channel Command Register */ |
| #define CD186x_IER 0x02 /* Interrupt Enable Register */ |
| #define CD186x_COR1 0x03 /* Channel Option Register 1 */ |
| #define CD186x_COR2 0x04 /* Channel Option Register 2 */ |
| #define CD186x_COR3 0x05 /* Channel Option Register 3 */ |
| #define CD186x_CCSR 0x06 /* Channel Control Status Register */ |
| #define CD186x_RDCR 0x07 /* Receive Data Count Register */ |
| #define CD186x_SCHR1 0x09 /* Special Character Register 1 */ |
| #define CD186x_SCHR2 0x0a /* Special Character Register 2 */ |
| #define CD186x_SCHR3 0x0b /* Special Character Register 3 */ |
| #define CD186x_SCHR4 0x0c /* Special Character Register 4 */ |
| #define CD186x_MCOR1 0x10 /* Modem Change Option 1 Register */ |
| #define CD186x_MCOR2 0x11 /* Modem Change Option 2 Register */ |
| #define CD186x_MCR 0x12 /* Modem Change Register */ |
| #define CD186x_RTPR 0x18 /* Receive Timeout Period Register */ |
| #define CD186x_MSVR 0x28 /* Modem Signal Value Register */ |
| #define CD186x_MSVRTS 0x29 /* Modem Signal Value Register */ |
| #define CD186x_MSVDTR 0x2a /* Modem Signal Value Register */ |
| #define CD186x_RBPRH 0x31 /* Receive Baud Rate Period Register High */ |
| #define CD186x_RBPRL 0x32 /* Receive Baud Rate Period Register Low */ |
| #define CD186x_TBPRH 0x39 /* Transmit Baud Rate Period Register High */ |
| #define CD186x_TBPRL 0x3a /* Transmit Baud Rate Period Register Low */ |
| |
| |
| /* Global Interrupt Vector Register (R/W) */ |
| |
| #define GIVR_ITMASK 0x07 /* Interrupt type mask */ |
| #define GIVR_IT_MODEM 0x01 /* Modem Signal Change Interrupt */ |
| #define GIVR_IT_TX 0x02 /* Transmit Data Interrupt */ |
| #define GIVR_IT_RCV 0x03 /* Receive Good Data Interrupt */ |
| #define GIVR_IT_REXC 0x07 /* Receive Exception Interrupt */ |
| |
| |
| /* Global Interrupt Channel Register (R/W) */ |
| |
| #define GICR_CHAN 0x1c /* Channel Number Mask */ |
| #define GICR_CHAN_OFF 2 /* Channel Number shift */ |
| |
| |
| /* Channel Address Register (R/W) */ |
| |
| #define CAR_CHAN 0x07 /* Channel Number Mask */ |
| #define CAR_A7 0x08 /* A7 Address Extension (unused) */ |
| |
| |
| /* Receive Character Status Register (R/O) */ |
| |
| #define RCSR_TOUT 0x80 /* Rx Timeout */ |
| #define RCSR_SCDET 0x70 /* Special Character Detected Mask */ |
| #define RCSR_NO_SC 0x00 /* No Special Characters Detected */ |
| #define RCSR_SC_1 0x10 /* Special Char 1 (or 1 & 3) Detected */ |
| #define RCSR_SC_2 0x20 /* Special Char 2 (or 2 & 4) Detected */ |
| #define RCSR_SC_3 0x30 /* Special Char 3 Detected */ |
| #define RCSR_SC_4 0x40 /* Special Char 4 Detected */ |
| #define RCSR_BREAK 0x08 /* Break has been detected */ |
| #define RCSR_PE 0x04 /* Parity Error */ |
| #define RCSR_FE 0x02 /* Frame Error */ |
| #define RCSR_OE 0x01 /* Overrun Error */ |
| |
| |
| /* Channel Command Register (R/W) (commands in groups can be OR-ed) */ |
| |
| #define CCR_HARDRESET 0x81 /* Reset the chip */ |
| |
| #define CCR_SOFTRESET 0x80 /* Soft Channel Reset */ |
| |
| #define CCR_CORCHG1 0x42 /* Channel Option Register 1 Changed */ |
| #define CCR_CORCHG2 0x44 /* Channel Option Register 2 Changed */ |
| #define CCR_CORCHG3 0x48 /* Channel Option Register 3 Changed */ |
| |
| #define CCR_SSCH1 0x21 /* Send Special Character 1 */ |
| |
| #define CCR_SSCH2 0x22 /* Send Special Character 2 */ |
| |
| #define CCR_SSCH3 0x23 /* Send Special Character 3 */ |
| |
| #define CCR_SSCH4 0x24 /* Send Special Character 4 */ |
| |
| #define CCR_TXEN 0x18 /* Enable Transmitter */ |
| #define CCR_RXEN 0x12 /* Enable Receiver */ |
| |
| #define CCR_TXDIS 0x14 /* Disable Transmitter */ |
| #define CCR_RXDIS 0x11 /* Disable Receiver */ |
| |
| |
| /* Interrupt Enable Register (R/W) */ |
| |
| #define IER_DSR 0x80 /* Enable interrupt on DSR change */ |
| #define IER_CD 0x40 /* Enable interrupt on CD change */ |
| #define IER_CTS 0x20 /* Enable interrupt on CTS change */ |
| #define IER_RXD 0x10 /* Enable interrupt on Receive Data */ |
| #define IER_RXSC 0x08 /* Enable interrupt on Receive Spec. Char */ |
| #define IER_TXRDY 0x04 /* Enable interrupt on TX FIFO empty */ |
| #define IER_TXEMPTY 0x02 /* Enable interrupt on TX completely empty */ |
| #define IER_RET 0x01 /* Enable interrupt on RX Exc. Timeout */ |
| |
| |
| /* Channel Option Register 1 (R/W) */ |
| |
| #define COR1_ODDP 0x80 /* Odd Parity */ |
| #define COR1_PARMODE 0x60 /* Parity Mode mask */ |
| #define COR1_NOPAR 0x00 /* No Parity */ |
| #define COR1_FORCEPAR 0x20 /* Force Parity */ |
| #define COR1_NORMPAR 0x40 /* Normal Parity */ |
| #define COR1_IGNORE 0x10 /* Ignore Parity on RX */ |
| #define COR1_STOPBITS 0x0c /* Number of Stop Bits */ |
| #define COR1_1SB 0x00 /* 1 Stop Bit */ |
| #define COR1_15SB 0x04 /* 1.5 Stop Bits */ |
| #define COR1_2SB 0x08 /* 2 Stop Bits */ |
| #define COR1_CHARLEN 0x03 /* Character Length */ |
| #define COR1_5BITS 0x00 /* 5 bits */ |
| #define COR1_6BITS 0x01 /* 6 bits */ |
| #define COR1_7BITS 0x02 /* 7 bits */ |
| #define COR1_8BITS 0x03 /* 8 bits */ |
| |
| |
| /* Channel Option Register 2 (R/W) */ |
| |
| #define COR2_IXM 0x80 /* Implied XON mode */ |
| #define COR2_TXIBE 0x40 /* Enable In-Band (XON/XOFF) Flow Control */ |
| #define COR2_ETC 0x20 /* Embedded Tx Commands Enable */ |
| #define COR2_LLM 0x10 /* Local Loopback Mode */ |
| #define COR2_RLM 0x08 /* Remote Loopback Mode */ |
| #define COR2_RTSAO 0x04 /* RTS Automatic Output Enable */ |
| #define COR2_CTSAE 0x02 /* CTS Automatic Enable */ |
| #define COR2_DSRAE 0x01 /* DSR Automatic Enable */ |
| |
| |
| /* Channel Option Register 3 (R/W) */ |
| |
| #define COR3_XONCH 0x80 /* XON is a pair of characters (1 & 3) */ |
| #define COR3_XOFFCH 0x40 /* XOFF is a pair of characters (2 & 4) */ |
| #define COR3_FCT 0x20 /* Flow-Control Transparency Mode */ |
| #define COR3_SCDE 0x10 /* Special Character Detection Enable */ |
| #define COR3_RXTH 0x0f /* RX FIFO Threshold value (1-8) */ |
| |
| |
| /* Channel Control Status Register (R/O) */ |
| |
| #define CCSR_RXEN 0x80 /* Receiver Enabled */ |
| #define CCSR_RXFLOFF 0x40 /* Receive Flow Off (XOFF was sent) */ |
| #define CCSR_RXFLON 0x20 /* Receive Flow On (XON was sent) */ |
| #define CCSR_TXEN 0x08 /* Transmitter Enabled */ |
| #define CCSR_TXFLOFF 0x04 /* Transmit Flow Off (got XOFF) */ |
| #define CCSR_TXFLON 0x02 /* Transmit Flow On (got XON) */ |
| |
| |
| /* Modem Change Option Register 1 (R/W) */ |
| |
| #define MCOR1_DSRZD 0x80 /* Detect 0->1 transition of DSR */ |
| #define MCOR1_CDZD 0x40 /* Detect 0->1 transition of CD */ |
| #define MCOR1_CTSZD 0x20 /* Detect 0->1 transition of CTS */ |
| #define MCOR1_DTRTH 0x0f /* Auto DTR flow control Threshold (1-8) */ |
| #define MCOR1_NODTRFC 0x0 /* Automatic DTR flow control disabled */ |
| |
| |
| /* Modem Change Option Register 2 (R/W) */ |
| |
| #define MCOR2_DSROD 0x80 /* Detect 1->0 transition of DSR */ |
| #define MCOR2_CDOD 0x40 /* Detect 1->0 transition of CD */ |
| #define MCOR2_CTSOD 0x20 /* Detect 1->0 transition of CTS */ |
| |
| /* Modem Change Register (R/W) */ |
| |
| #define MCR_DSRCHG 0x80 /* DSR Changed */ |
| #define MCR_CDCHG 0x40 /* CD Changed */ |
| #define MCR_CTSCHG 0x20 /* CTS Changed */ |
| |
| |
| /* Modem Signal Value Register (R/W) */ |
| |
| #define MSVR_DSR 0x80 /* Current state of DSR input */ |
| #define MSVR_CD 0x40 /* Current state of CD input */ |
| #define MSVR_CTS 0x20 /* Current state of CTS input */ |
| #define MSVR_DTR 0x02 /* Current state of DTR output */ |
| #define MSVR_RTS 0x01 /* Current state of RTS output */ |
| |
| |
| /* Escape characters */ |
| |
| #define CD186x_C_ESC 0x00 /* Escape character */ |
| #define CD186x_C_SBRK 0x81 /* Start sending BREAK */ |
| #define CD186x_C_DELAY 0x82 /* Delay output */ |
| #define CD186x_C_EBRK 0x83 /* Stop sending BREAK */ |
| |
| #define SRSR_RREQint 0x10 /* This chip wants "rec" serviced */ |
| #define SRSR_TREQint 0x04 /* This chip wants "transmit" serviced */ |
| #define SRSR_MREQint 0x01 /* This chip wants "mdm change" serviced */ |
| |
| |
| |
| #define SRCR_PKGTYPE 0x80 |
| #define SRCR_REGACKEN 0x40 |
| #define SRCR_DAISYEN 0x20 |
| #define SRCR_GLOBPRI 0x10 |
| #define SRCR_UNFAIR 0x08 |
| #define SRCR_AUTOPRI 0x02 |
| #define SRCR_PRISEL 0x01 |
| |
| |