gs: use tty_port
Switch drivers using the old "generic serial" driver to use the tty_port
structures
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/drivers/char/sx.c b/drivers/char/sx.c
index b1a7a8c..b1239ee 100644
--- a/drivers/char/sx.c
+++ b/drivers/char/sx.c
@@ -1,4 +1,3 @@
-
/* sx.c -- driver for the Specialix SX series cards.
*
* This driver will also support the older SI, and XIO cards.
@@ -930,7 +929,7 @@
func_enter2();
- if (!port->gs.tty)
+ if (!port->gs.port.tty)
return 0;
/* What is this doing here? -- REW
@@ -941,19 +940,19 @@
sx_set_baud(port);
-#define CFLAG port->gs.tty->termios->c_cflag
+#define CFLAG port->gs.port.tty->termios->c_cflag
sx_write_channel_byte(port, hi_mr1,
- (C_PARENB(port->gs.tty) ? MR1_WITH : MR1_NONE) |
- (C_PARODD(port->gs.tty) ? MR1_ODD : MR1_EVEN) |
- (C_CRTSCTS(port->gs.tty) ? MR1_RTS_RXFLOW : 0) |
+ (C_PARENB(port->gs.port.tty) ? MR1_WITH : MR1_NONE) |
+ (C_PARODD(port->gs.port.tty) ? MR1_ODD : MR1_EVEN) |
+ (C_CRTSCTS(port->gs.port.tty) ? MR1_RTS_RXFLOW : 0) |
(((CFLAG & CSIZE) == CS8) ? MR1_8_BITS : 0) |
(((CFLAG & CSIZE) == CS7) ? MR1_7_BITS : 0) |
(((CFLAG & CSIZE) == CS6) ? MR1_6_BITS : 0) |
(((CFLAG & CSIZE) == CS5) ? MR1_5_BITS : 0));
sx_write_channel_byte(port, hi_mr2,
- (C_CRTSCTS(port->gs.tty) ? MR2_CTS_TXFLOW : 0) |
- (C_CSTOPB(port->gs.tty) ? MR2_2_STOP :
+ (C_CRTSCTS(port->gs.port.tty) ? MR2_CTS_TXFLOW : 0) |
+ (C_CSTOPB(port->gs.port.tty) ? MR2_2_STOP :
MR2_1_STOP));
switch (CFLAG & CSIZE) {
@@ -976,44 +975,44 @@
}
sx_write_channel_byte(port, hi_prtcl,
- (I_IXON(port->gs.tty) ? SP_TXEN : 0) |
- (I_IXOFF(port->gs.tty) ? SP_RXEN : 0) |
- (I_IXANY(port->gs.tty) ? SP_TANY : 0) | SP_DCEN);
+ (I_IXON(port->gs.port.tty) ? SP_TXEN : 0) |
+ (I_IXOFF(port->gs.port.tty) ? SP_RXEN : 0) |
+ (I_IXANY(port->gs.port.tty) ? SP_TANY : 0) | SP_DCEN);
sx_write_channel_byte(port, hi_break,
- (I_IGNBRK(port->gs.tty) ? BR_IGN : 0 |
- I_BRKINT(port->gs.tty) ? BR_INT : 0));
+ (I_IGNBRK(port->gs.port.tty) ? BR_IGN : 0 |
+ I_BRKINT(port->gs.port.tty) ? BR_INT : 0));
- sx_write_channel_byte(port, hi_txon, START_CHAR(port->gs.tty));
- sx_write_channel_byte(port, hi_rxon, START_CHAR(port->gs.tty));
- sx_write_channel_byte(port, hi_txoff, STOP_CHAR(port->gs.tty));
- sx_write_channel_byte(port, hi_rxoff, STOP_CHAR(port->gs.tty));
+ sx_write_channel_byte(port, hi_txon, START_CHAR(port->gs.port.tty));
+ sx_write_channel_byte(port, hi_rxon, START_CHAR(port->gs.port.tty));
+ sx_write_channel_byte(port, hi_txoff, STOP_CHAR(port->gs.port.tty));
+ sx_write_channel_byte(port, hi_rxoff, STOP_CHAR(port->gs.port.tty));
sx_reconfigure_port(port);
/* Tell line discipline whether we will do input cooking */
- if (I_OTHER(port->gs.tty)) {
- clear_bit(TTY_HW_COOK_IN, &port->gs.tty->flags);
+ if (I_OTHER(port->gs.port.tty)) {
+ clear_bit(TTY_HW_COOK_IN, &port->gs.port.tty->flags);
} else {
- set_bit(TTY_HW_COOK_IN, &port->gs.tty->flags);
+ set_bit(TTY_HW_COOK_IN, &port->gs.port.tty->flags);
}
sx_dprintk(SX_DEBUG_TERMIOS, "iflags: %x(%d) ",
- (unsigned int)port->gs.tty->termios->c_iflag,
- I_OTHER(port->gs.tty));
+ (unsigned int)port->gs.port.tty->termios->c_iflag,
+ I_OTHER(port->gs.port.tty));
/* Tell line discipline whether we will do output cooking.
* If OPOST is set and no other output flags are set then we can do output
* processing. Even if only *one* other flag in the O_OTHER group is set
* we do cooking in software.
*/
- if (O_OPOST(port->gs.tty) && !O_OTHER(port->gs.tty)) {
- set_bit(TTY_HW_COOK_OUT, &port->gs.tty->flags);
+ if (O_OPOST(port->gs.port.tty) && !O_OTHER(port->gs.port.tty)) {
+ set_bit(TTY_HW_COOK_OUT, &port->gs.port.tty->flags);
} else {
- clear_bit(TTY_HW_COOK_OUT, &port->gs.tty->flags);
+ clear_bit(TTY_HW_COOK_OUT, &port->gs.port.tty->flags);
}
sx_dprintk(SX_DEBUG_TERMIOS, "oflags: %x(%d)\n",
- (unsigned int)port->gs.tty->termios->c_oflag,
- O_OTHER(port->gs.tty));
+ (unsigned int)port->gs.port.tty->termios->c_oflag,
+ O_OTHER(port->gs.port.tty));
/* port->c_dcd = sx_get_CD (port); */
func_exit();
return 0;
@@ -1102,8 +1101,8 @@
sx_disable_tx_interrupts(port);
}
- if ((port->gs.xmit_cnt <= port->gs.wakeup_chars) && port->gs.tty) {
- tty_wakeup(port->gs.tty);
+ if ((port->gs.xmit_cnt <= port->gs.wakeup_chars) && port->gs.port.tty) {
+ tty_wakeup(port->gs.port.tty);
sx_dprintk(SX_DEBUG_TRANSMIT, "Waking up.... ldisc (%d)....\n",
port->gs.wakeup_chars);
}
@@ -1126,7 +1125,7 @@
unsigned char *rp;
func_enter2();
- tty = port->gs.tty;
+ tty = port->gs.port.tty;
while (1) {
rx_op = sx_read_channel_byte(port, hi_rxopos);
c = (sx_read_channel_byte(port, hi_rxipos) - rx_op) & 0xff;
@@ -1211,12 +1210,12 @@
/* DCD went UP */
if ((sx_read_channel_byte(port, hi_hstat) !=
HS_IDLE_CLOSED) &&
- !(port->gs.tty->termios->
+ !(port->gs.port.tty->termios->
c_cflag & CLOCAL)) {
/* Are we blocking in open? */
sx_dprintk(SX_DEBUG_MODEMSIGNALS, "DCD "
"active, unblocking open\n");
- wake_up_interruptible(&port->gs.
+ wake_up_interruptible(&port->gs.port.
open_wait);
} else {
sx_dprintk(SX_DEBUG_MODEMSIGNALS, "DCD "
@@ -1224,10 +1223,10 @@
}
} else {
/* DCD went down! */
- if (!(port->gs.tty->termios->c_cflag & CLOCAL)){
+ if (!(port->gs.port.tty->termios->c_cflag & CLOCAL)){
sx_dprintk(SX_DEBUG_MODEMSIGNALS, "DCD "
"dropped. hanging up....\n");
- tty_hangup(port->gs.tty);
+ tty_hangup(port->gs.port.tty);
} else {
sx_dprintk(SX_DEBUG_MODEMSIGNALS, "DCD "
"dropped. ignoring.\n");
@@ -1325,7 +1324,7 @@
for (i = 0; i < board->nports; i++) {
port = &board->ports[i];
- if (port->gs.flags & GS_ACTIVE) {
+ if (port->gs.port.flags & GS_ACTIVE) {
if (sx_read_channel_byte(port, hi_state)) {
sx_dprintk(SX_DEBUG_INTERRUPTS, "Port %d: "
"modem signal change?... \n",i);
@@ -1334,7 +1333,7 @@
if (port->gs.xmit_cnt) {
sx_transmit_chars(port);
}
- if (!(port->gs.flags & SX_RX_THROTTLE)) {
+ if (!(port->gs.port.flags & SX_RX_THROTTLE)) {
sx_receive_chars(port);
}
}
@@ -1373,7 +1372,7 @@
struct sx_port *port = ptr;
func_enter2();
- port->gs.flags &= ~GS_TX_INTEN;
+ port->gs.port.flags &= ~GS_TX_INTEN;
func_exit();
}
@@ -1394,7 +1393,7 @@
/* XXX Must be "HIGH_WATER" for SI card according to doc. */
if (data_in_buffer < LOW_WATER)
- port->gs.flags &= ~GS_TX_INTEN;
+ port->gs.port.flags &= ~GS_TX_INTEN;
func_exit();
}
@@ -1442,8 +1441,8 @@
func_enter();
- port->gs.flags &= ~GS_ACTIVE;
- if (port->gs.tty && (port->gs.tty->termios->c_cflag & HUPCL)) {
+ port->gs.port.flags &= ~GS_ACTIVE;
+ if (port->gs.port.tty && (port->gs.port.tty->termios->c_cflag & HUPCL)) {
sx_setsignals(port, 0, 0);
sx_reconfigure_port(port);
}
@@ -1485,8 +1484,8 @@
spin_lock_irqsave(&port->gs.driver_lock, flags);
tty->driver_data = port;
- port->gs.tty = tty;
- port->gs.count++;
+ port->gs.port.tty = tty;
+ port->gs.port.count++;
spin_unlock_irqrestore(&port->gs.driver_lock, flags);
sx_dprintk(SX_DEBUG_OPEN, "starting port\n");
@@ -1497,12 +1496,12 @@
retval = gs_init_port(&port->gs);
sx_dprintk(SX_DEBUG_OPEN, "done gs_init\n");
if (retval) {
- port->gs.count--;
+ port->gs.port.count--;
return retval;
}
- port->gs.flags |= GS_ACTIVE;
- if (port->gs.count <= 1)
+ port->gs.port.flags |= GS_ACTIVE;
+ if (port->gs.port.count <= 1)
sx_setsignals(port, 1, 1);
#if 0
@@ -1513,12 +1512,12 @@
my_hd_io(port->board->base + port->ch_base, sizeof(*port));
#endif
- if (port->gs.count <= 1) {
+ if (port->gs.port.count <= 1) {
if (sx_send_command(port, HS_LOPEN, -1, HS_IDLE_OPEN) != 1) {
printk(KERN_ERR "sx: Card didn't respond to LOPEN "
"command.\n");
spin_lock_irqsave(&port->gs.driver_lock, flags);
- port->gs.count--;
+ port->gs.port.count--;
spin_unlock_irqrestore(&port->gs.driver_lock, flags);
return -EIO;
}
@@ -1526,11 +1525,11 @@
retval = gs_block_til_ready(port, filp);
sx_dprintk(SX_DEBUG_OPEN, "Block til ready returned %d. Count=%d\n",
- retval, port->gs.count);
+ retval, port->gs.port.count);
if (retval) {
/*
- * Don't lower gs.count here because sx_close() will be called later
+ * Don't lower gs.port.count here because sx_close() will be called later
*/
return retval;
@@ -1571,14 +1570,14 @@
}
sx_dprintk(SX_DEBUG_CLOSE, "waited %d jiffies for close. count=%d\n",
- 5 * HZ - to - 1, port->gs.count);
+ 5 * HZ - to - 1, port->gs.port.count);
- if (port->gs.count) {
+ if (port->gs.port.count) {
sx_dprintk(SX_DEBUG_CLOSE, "WARNING port count:%d\n",
- port->gs.count);
+ port->gs.port.count);
/*printk("%s SETTING port count to zero: %p count: %d\n",
- __func__, port, port->gs.count);
- port->gs.count = 0;*/
+ __func__, port, port->gs.port.count);
+ port->gs.port.count = 0;*/
}
func_exit();
@@ -1939,7 +1938,7 @@
* control then throttle the port.
*/
if ((tty->termios->c_cflag & CRTSCTS) || (I_IXOFF(tty))) {
- port->gs.flags |= SX_RX_THROTTLE;
+ port->gs.port.flags |= SX_RX_THROTTLE;
}
func_exit();
}
@@ -1953,7 +1952,7 @@
* this port in case we disabled flow control while the port
* was throttled
*/
- port->gs.flags &= ~SX_RX_THROTTLE;
+ port->gs.port.flags &= ~SX_RX_THROTTLE;
func_exit();
return;
}
@@ -2408,9 +2407,7 @@
/*
* Initializing wait queue
*/
- init_waitqueue_head(&port->gs.open_wait);
- init_waitqueue_head(&port->gs.close_wait);
-
+ tty_port_init(&port->gs.port);
port++;
}
}