e1000: Fix MSI only interrupt handler routine
Unfortunately the read-free MSI interrupt handler needs to flush write
the icr register and thus we can't be read-free. Our MSI irq routine
thus becomes a lot more simpler since we don't need to track link state
anymore.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
diff --git a/drivers/net/e1000/e1000.h b/drivers/net/e1000/e1000.h
index f091042..8e7acb0 100644
--- a/drivers/net/e1000/e1000.h
+++ b/drivers/net/e1000/e1000.h
@@ -257,7 +257,6 @@
spinlock_t tx_queue_lock;
#endif
atomic_t irq_sem;
- unsigned int detect_link;
unsigned int total_tx_bytes;
unsigned int total_tx_packets;
unsigned int total_rx_bytes;
diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c
index c6259c7..d408949 100644
--- a/drivers/net/e1000/e1000_main.c
+++ b/drivers/net/e1000/e1000_main.c
@@ -3765,8 +3765,8 @@
* @data: pointer to a network interface device structure
**/
-static
-irqreturn_t e1000_intr_msi(int irq, void *data)
+static irqreturn_t
+e1000_intr_msi(int irq, void *data)
{
struct net_device *netdev = data;
struct e1000_adapter *adapter = netdev_priv(netdev);
@@ -3774,49 +3774,27 @@
#ifndef CONFIG_E1000_NAPI
int i;
#endif
+ uint32_t icr = E1000_READ_REG(hw, ICR);
- /* this code avoids the read of ICR but has to get 1000 interrupts
- * at every link change event before it will notice the change */
- if (++adapter->detect_link >= 1000) {
- uint32_t icr = E1000_READ_REG(hw, ICR);
#ifdef CONFIG_E1000_NAPI
- /* read ICR disables interrupts using IAM, so keep up with our
- * enable/disable accounting */
- atomic_inc(&adapter->irq_sem);
+ /* read ICR disables interrupts using IAM, so keep up with our
+ * enable/disable accounting */
+ atomic_inc(&adapter->irq_sem);
#endif
- adapter->detect_link = 0;
- if ((icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC)) &&
- (icr & E1000_ICR_INT_ASSERTED)) {
- hw->get_link_status = 1;
- /* 80003ES2LAN workaround--
- * For packet buffer work-around on link down event;
- * disable receives here in the ISR and
- * reset adapter in watchdog
- */
- if (netif_carrier_ok(netdev) &&
- (adapter->hw.mac_type == e1000_80003es2lan)) {
- /* disable receives */
- uint32_t rctl = E1000_READ_REG(hw, RCTL);
- E1000_WRITE_REG(hw, RCTL, rctl & ~E1000_RCTL_EN);
- }
- /* guard against interrupt when we're going down */
- if (!test_bit(__E1000_DOWN, &adapter->flags))
- mod_timer(&adapter->watchdog_timer,
- jiffies + 1);
+ if (icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC)) {
+ hw->get_link_status = 1;
+ /* 80003ES2LAN workaround-- For packet buffer work-around on
+ * link down event; disable receives here in the ISR and reset
+ * adapter in watchdog */
+ if (netif_carrier_ok(netdev) &&
+ (adapter->hw.mac_type == e1000_80003es2lan)) {
+ /* disable receives */
+ uint32_t rctl = E1000_READ_REG(hw, RCTL);
+ E1000_WRITE_REG(hw, RCTL, rctl & ~E1000_RCTL_EN);
}
- } else {
- E1000_WRITE_REG(hw, ICR, (0xffffffff & ~(E1000_ICR_RXSEQ |
- E1000_ICR_LSC)));
- /* bummer we have to flush here, but things break otherwise as
- * some event appears to be lost or delayed and throughput
- * drops. In almost all tests this flush is un-necessary */
- E1000_WRITE_FLUSH(hw);
-#ifdef CONFIG_E1000_NAPI
- /* Interrupt Auto-Mask (IAM)...upon writing ICR, interrupts are
- * masked. No need for the IMC write, but it does mean we
- * should account for it ASAP. */
- atomic_inc(&adapter->irq_sem);
-#endif
+ /* guard against interrupt when we're going down */
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ mod_timer(&adapter->watchdog_timer, jiffies + 1);
}
#ifdef CONFIG_E1000_NAPI