hwmon: (w83627hf) Stop using globals for I/O port numbers
Stop using global variables REG and VAL for I/O port numbers. This is
ugly and unsafe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rodolfo Giometti <giometti@linux.it>
diff --git a/drivers/hwmon/w83627hf.c b/drivers/hwmon/w83627hf.c
index d67407d..b257c72 100644
--- a/drivers/hwmon/w83627hf.c
+++ b/drivers/hwmon/w83627hf.c
@@ -59,6 +59,11 @@
#define DRVNAME "w83627hf"
enum chips { w83627hf, w83627thf, w83697hf, w83637hf, w83687thf };
+struct w83627hf_sio_data {
+ enum chips type;
+ int sioaddr;
+};
+
static u8 force_i2c = 0x1f;
module_param(force_i2c, byte, 0);
MODULE_PARM_DESC(force_i2c,
@@ -73,9 +78,7 @@
MODULE_PARM_DESC(force_id, "Override the detected device ID");
/* modified from kernel/include/traps.c */
-static int REG; /* The register to read/write */
#define DEV 0x07 /* Register: Logical device select */
-static int VAL; /* The value to read/write */
/* logical device numbers for superio_select (below) */
#define W83627HF_LD_FDC 0x00
@@ -105,37 +108,37 @@
#define W83687THF_VID_DATA 0xF1 /* w83687thf only */
static inline void
-superio_outb(int reg, int val)
+superio_outb(struct w83627hf_sio_data *sio, int reg, int val)
{
- outb(reg, REG);
- outb(val, VAL);
+ outb(reg, sio->sioaddr);
+ outb(val, sio->sioaddr + 1);
}
static inline int
-superio_inb(int reg)
+superio_inb(struct w83627hf_sio_data *sio, int reg)
{
- outb(reg, REG);
- return inb(VAL);
+ outb(reg, sio->sioaddr);
+ return inb(sio->sioaddr + 1);
}
static inline void
-superio_select(int ld)
+superio_select(struct w83627hf_sio_data *sio, int ld)
{
- outb(DEV, REG);
- outb(ld, VAL);
+ outb(DEV, sio->sioaddr);
+ outb(ld, sio->sioaddr + 1);
}
static inline void
-superio_enter(void)
+superio_enter(struct w83627hf_sio_data *sio)
{
- outb(0x87, REG);
- outb(0x87, REG);
+ outb(0x87, sio->sioaddr);
+ outb(0x87, sio->sioaddr);
}
static inline void
-superio_exit(void)
+superio_exit(struct w83627hf_sio_data *sio)
{
- outb(0xAA, REG);
+ outb(0xAA, sio->sioaddr);
}
#define W627_DEVID 0x52
@@ -376,10 +379,6 @@
u8 vrm_ovt; /* Register value, 627THF/637HF/687THF only */
};
-struct w83627hf_sio_data {
- enum chips type;
-};
-
static int w83627hf_probe(struct platform_device *pdev);
static int __devexit w83627hf_remove(struct platform_device *pdev);
@@ -1136,11 +1135,8 @@
"W83687THF",
};
- REG = sioaddr;
- VAL = sioaddr + 1;
-
- superio_enter();
- val = force_id ? force_id : superio_inb(DEVID);
+ superio_enter(sio_data);
+ val = force_id ? force_id : superio_inb(sio_data, DEVID);
switch (val) {
case W627_DEVID:
sio_data->type = w83627hf;
@@ -1164,9 +1160,9 @@
goto exit;
}
- superio_select(W83627HF_LD_HWM);
- val = (superio_inb(WINB_BASE_REG) << 8) |
- superio_inb(WINB_BASE_REG + 1);
+ superio_select(sio_data, W83627HF_LD_HWM);
+ val = (superio_inb(sio_data, WINB_BASE_REG) << 8) |
+ superio_inb(sio_data, WINB_BASE_REG + 1);
*addr = val & WINB_ALIGNMENT;
if (*addr == 0) {
printk(KERN_WARNING DRVNAME ": Base address not set, "
@@ -1174,18 +1170,19 @@
goto exit;
}
- val = superio_inb(WINB_ACT_REG);
+ val = superio_inb(sio_data, WINB_ACT_REG);
if (!(val & 0x01)) {
printk(KERN_WARNING DRVNAME ": Enabling HWM logical device\n");
- superio_outb(WINB_ACT_REG, val | 0x01);
+ superio_outb(sio_data, WINB_ACT_REG, val | 0x01);
}
err = 0;
+ sio_data->sioaddr = sioaddr;
pr_info(DRVNAME ": Found %s chip at %#x\n",
names[sio_data->type], *addr);
exit:
- superio_exit();
+ superio_exit(sio_data);
return err;
}
@@ -1500,20 +1497,21 @@
static int __devinit w83627thf_read_gpio5(struct platform_device *pdev)
{
+ struct w83627hf_sio_data *sio_data = pdev->dev.platform_data;
int res = 0xff, sel;
- superio_enter();
- superio_select(W83627HF_LD_GPIO5);
+ superio_enter(sio_data);
+ superio_select(sio_data, W83627HF_LD_GPIO5);
/* Make sure these GPIO pins are enabled */
- if (!(superio_inb(W83627THF_GPIO5_EN) & (1<<3))) {
+ if (!(superio_inb(sio_data, W83627THF_GPIO5_EN) & (1<<3))) {
dev_dbg(&pdev->dev, "GPIO5 disabled, no VID function\n");
goto exit;
}
/* Make sure the pins are configured for input
There must be at least five (VRM 9), and possibly 6 (VRM 10) */
- sel = superio_inb(W83627THF_GPIO5_IOSR) & 0x3f;
+ sel = superio_inb(sio_data, W83627THF_GPIO5_IOSR) & 0x3f;
if ((sel & 0x1f) != 0x1f) {
dev_dbg(&pdev->dev, "GPIO5 not configured for VID "
"function\n");
@@ -1521,37 +1519,38 @@
}
dev_info(&pdev->dev, "Reading VID from GPIO5\n");
- res = superio_inb(W83627THF_GPIO5_DR) & sel;
+ res = superio_inb(sio_data, W83627THF_GPIO5_DR) & sel;
exit:
- superio_exit();
+ superio_exit(sio_data);
return res;
}
static int __devinit w83687thf_read_vid(struct platform_device *pdev)
{
+ struct w83627hf_sio_data *sio_data = pdev->dev.platform_data;
int res = 0xff;
- superio_enter();
- superio_select(W83627HF_LD_HWM);
+ superio_enter(sio_data);
+ superio_select(sio_data, W83627HF_LD_HWM);
/* Make sure these GPIO pins are enabled */
- if (!(superio_inb(W83687THF_VID_EN) & (1 << 2))) {
+ if (!(superio_inb(sio_data, W83687THF_VID_EN) & (1 << 2))) {
dev_dbg(&pdev->dev, "VID disabled, no VID function\n");
goto exit;
}
/* Make sure the pins are configured for input */
- if (!(superio_inb(W83687THF_VID_CFG) & (1 << 4))) {
+ if (!(superio_inb(sio_data, W83687THF_VID_CFG) & (1 << 4))) {
dev_dbg(&pdev->dev, "VID configured as output, "
"no VID function\n");
goto exit;
}
- res = superio_inb(W83687THF_VID_DATA) & 0x3f;
+ res = superio_inb(sio_data, W83687THF_VID_DATA) & 0x3f;
exit:
- superio_exit();
+ superio_exit(sio_data);
return res;
}