bnx2x: Warpcore HW reset following fan failure
Put Warpcore in low power mode in case of fan failure to reduce heat.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
index de03730..7eabcee 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
@@ -8216,7 +8216,15 @@
static void bnx2x_warpcore_hw_reset(struct bnx2x_phy *phy,
struct link_params *params)
{
+ struct bnx2x *bp = params->bp;
bnx2x_warpcore_power_module(params, phy, 0);
+ /* Put Warpcore in low power mode */
+ REG_WR(bp, MISC_REG_WC0_RESET, 0x0c0e);
+
+ /* Put LCPLL in low power mode */
+ REG_WR(bp, MISC_REG_LCPLL_E40_PWRDWN, 1);
+ REG_WR(bp, MISC_REG_LCPLL_E40_RESETB_ANA, 0);
+ REG_WR(bp, MISC_REG_LCPLL_E40_RESETB_DIG, 0);
}
static void bnx2x_power_sfp_module(struct link_params *params,
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h
index 92584d3..d5a0dde 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h
@@ -1622,6 +1622,14 @@
register bits. */
#define MISC_REG_LCPLL_CTRL_1 0xa2a4
#define MISC_REG_LCPLL_CTRL_REG_2 0xa2a8
+/* [RW 1] LCPLL power down. Global register. Active High. Reset on POR
+ * reset. */
+#define MISC_REG_LCPLL_E40_PWRDWN 0xaa74
+/* [RW 1] LCPLL VCO reset. Global register. Active Low Reset on POR reset. */
+#define MISC_REG_LCPLL_E40_RESETB_ANA 0xaa78
+/* [RW 1] LCPLL post-divider reset. Global register. Active Low Reset on POR
+ * reset. */
+#define MISC_REG_LCPLL_E40_RESETB_DIG 0xaa7c
/* [RW 4] Interrupt mask register #0 read/write */
#define MISC_REG_MISC_INT_MASK 0xa388
/* [RW 1] Parity mask register #0 read/write */
@@ -1757,6 +1765,7 @@
* is compared to the value on ctrl_md_devad. Drives output
* misc_xgxs0_phy_addr. Global register. */
#define MISC_REG_WC0_CTRL_PHY_ADDR 0xa9cc
+#define MISC_REG_WC0_RESET 0xac30
/* [RW 2] XMAC Core port mode. Indicates the number of ports on the system
side. This should be less than or equal to phy_port_mode; if some of the
ports are not used. This enables reduction of frequency on the core side.