drm/i915: Unduplicate CHV signal level code
The code for programming voltage swing and emphasis was duplicated
between DP and HDMI code. Move that to a new file, intel_dpio_phy.c.
v2: Keep the "Use 800mV-0dB" comment in the HDMI code. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461761065-21195-3-git-send-email-ander.conselvan.de.oliveira@intel.com
diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
index 718eba2..494e02e 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -1921,77 +1921,11 @@
/* Deassert data lane reset */
chv_data_lane_soft_reset(encoder, false);
- /* Clear calc init */
- val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW10(ch));
- val &= ~(DPIO_PCS_SWING_CALC_TX0_TX2 | DPIO_PCS_SWING_CALC_TX1_TX3);
- val &= ~(DPIO_PCS_TX1DEEMP_MASK | DPIO_PCS_TX2DEEMP_MASK);
- val |= DPIO_PCS_TX1DEEMP_9P5 | DPIO_PCS_TX2DEEMP_9P5;
- vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW10(ch), val);
-
- val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW10(ch));
- val &= ~(DPIO_PCS_SWING_CALC_TX0_TX2 | DPIO_PCS_SWING_CALC_TX1_TX3);
- val &= ~(DPIO_PCS_TX1DEEMP_MASK | DPIO_PCS_TX2DEEMP_MASK);
- val |= DPIO_PCS_TX1DEEMP_9P5 | DPIO_PCS_TX2DEEMP_9P5;
- vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW10(ch), val);
-
- val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW9(ch));
- val &= ~(DPIO_PCS_TX1MARGIN_MASK | DPIO_PCS_TX2MARGIN_MASK);
- val |= DPIO_PCS_TX1MARGIN_000 | DPIO_PCS_TX2MARGIN_000;
- vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW9(ch), val);
-
- val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW9(ch));
- val &= ~(DPIO_PCS_TX1MARGIN_MASK | DPIO_PCS_TX2MARGIN_MASK);
- val |= DPIO_PCS_TX1MARGIN_000 | DPIO_PCS_TX2MARGIN_000;
- vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW9(ch), val);
+ mutex_unlock(&dev_priv->sb_lock);
/* FIXME: Program the support xxx V-dB */
/* Use 800mV-0dB */
- for (i = 0; i < 4; i++) {
- val = vlv_dpio_read(dev_priv, pipe, CHV_TX_DW4(ch, i));
- val &= ~DPIO_SWING_DEEMPH9P5_MASK;
- val |= 128 << DPIO_SWING_DEEMPH9P5_SHIFT;
- vlv_dpio_write(dev_priv, pipe, CHV_TX_DW4(ch, i), val);
- }
-
- for (i = 0; i < 4; i++) {
- val = vlv_dpio_read(dev_priv, pipe, CHV_TX_DW2(ch, i));
-
- val &= ~DPIO_SWING_MARGIN000_MASK;
- val |= 102 << DPIO_SWING_MARGIN000_SHIFT;
-
- /*
- * Supposedly this value shouldn't matter when unique transition
- * scale is disabled, but in fact it does matter. Let's just
- * always program the same value and hope it's OK.
- */
- val &= ~(0xff << DPIO_UNIQ_TRANS_SCALE_SHIFT);
- val |= 0x9a << DPIO_UNIQ_TRANS_SCALE_SHIFT;
-
- vlv_dpio_write(dev_priv, pipe, CHV_TX_DW2(ch, i), val);
- }
-
- /*
- * The document said it needs to set bit 27 for ch0 and bit 26
- * for ch1. Might be a typo in the doc.
- * For now, for this unique transition scale selection, set bit
- * 27 for ch0 and ch1.
- */
- for (i = 0; i < 4; i++) {
- val = vlv_dpio_read(dev_priv, pipe, CHV_TX_DW3(ch, i));
- val &= ~DPIO_TX_UNIQ_TRANS_SCALE_EN;
- vlv_dpio_write(dev_priv, pipe, CHV_TX_DW3(ch, i), val);
- }
-
- /* Start swing calculation */
- val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW10(ch));
- val |= DPIO_PCS_SWING_CALC_TX0_TX2 | DPIO_PCS_SWING_CALC_TX1_TX3;
- vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW10(ch), val);
-
- val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW10(ch));
- val |= DPIO_PCS_SWING_CALC_TX0_TX2 | DPIO_PCS_SWING_CALC_TX1_TX3;
- vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW10(ch), val);
-
- mutex_unlock(&dev_priv->sb_lock);
+ chv_set_phy_signal_level(encoder, 128, 102, false);
intel_hdmi->set_infoframes(&encoder->base,
intel_crtc->config->has_hdmi_sink,