V4L/DVB (10957): cx231xx: Fix CodingStyle
Fixes several CodingStyle issues on the driver.
Signed-off-by: Srinivasa Deevi <srinivasa.deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
diff --git a/drivers/media/video/cx231xx/cx231xx-i2c.c b/drivers/media/video/cx231xx/cx231xx-i2c.c
index c250ad2..1af8757 100644
--- a/drivers/media/video/cx231xx/cx231xx-i2c.c
+++ b/drivers/media/video/cx231xx/cx231xx-i2c.c
@@ -2,8 +2,8 @@
cx231xx-i2c.c - driver for Conexant Cx23100/101/102 USB video capture devices
Copyright (C) 2008 <srinivasa.deevi at conexant dot com>
- Based on em28xx driver
- Based on Cx23885 driver
+ Based on em28xx driver
+ Based on Cx23885 driver
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
@@ -42,8 +42,8 @@
#define dprintk1(lvl, fmt, args...) \
do { \
if (i2c_debug >= lvl) { \
- printk(fmt, ##args); \
- } \
+ printk(fmt, ##args); \
+ } \
} while (0)
#define dprintk2(lvl, fmt, args...) \
@@ -78,8 +78,8 @@
if (size == 2) { /* register write sub addr */
- /* Just writing sub address will cause problem to XC5000
- So ignore the request */
+ /* Just writing sub address will cause problem to XC5000
+ So ignore the request */
return 0;
} else if (size == 4) { /* register write with sub addr */
@@ -92,7 +92,8 @@
switch (saddr) {
case 0x0000: /* start tuner calibration mode */
need_gpio = 1;
- dev->xc_fw_load_done = 1; /* FW Loading is done */
+ /* FW Loading is done */
+ dev->xc_fw_load_done = 1;
break;
case 0x000D: /* Set signal source */
case 0x0001: /* Set TV standard - Video */
@@ -108,8 +109,8 @@
if (need_gpio) {
dprintk1(1,
- " GPIO W R I T E : addr 0x%x, len %d, saddr 0x%x\n",
- msg->addr, msg->len, saddr);
+ "GPIO WRITE: addr 0x%x, len %d, saddr 0x%x\n",
+ msg->addr, msg->len, saddr);
return dev->cx231xx_gpio_i2c_write(dev,
msg->addr,
@@ -196,8 +197,8 @@
switch (saddr) {
case 0x0009: /* BUSY check */
dprintk1(1,
- " GPIO R E A D : Special case BUSY check \n");
- /* Try to read BUSY register, just set it to zero */
+ "GPIO R E A D: Special case BUSY check \n");
+ /*Try read BUSY register, just set it to zero*/
msg->buf[0] = 0;
if (msg->len == 2)
msg->buf[1] = 0;
@@ -209,12 +210,14 @@
}
if (need_gpio) {
- /* this is a special case to handle Xceive tuner clock stretch issue
- with gpio based I2C interface */
+ /* this is a special case to handle Xceive tuner
+ clock stretch issue with gpio based I2C */
+
dprintk1(1,
- " GPIO R E A D : addr 0x%x, len %d, saddr 0x%x\n",
- msg->addr, msg->len,
- msg->buf[0] << 8 | msg->buf[1]);
+ "GPIO R E A D: addr 0x%x, len %d, saddr 0x%x\n",
+ msg->addr, msg->len,
+ msg->buf[0] << 8 | msg->buf[1]);
+
status =
dev->cx231xx_gpio_i2c_write(dev, msg->addr,
msg->buf,
@@ -281,8 +284,8 @@
if ((msg2->len < 16)) {
dprintk1(1,
- " i2c_read : addr 0x%x, len %d, subaddr 0x%x, leng %d\n",
- msg2->addr, msg2->len, saddr, msg1->len);
+ "i2c_read: addr 0x%x, len %d, saddr 0x%x, len %d\n",
+ msg2->addr, msg2->len, saddr, msg1->len);
switch (saddr) {
case 0x0008: /* read FW load status */
@@ -368,7 +371,8 @@
dprintk2(2, "%s %s addr=%x len=%d:",
(msgs[i].flags & I2C_M_RD) ? "read" : "write",
i == num - 1 ? "stop" : "nonstop", addr, msgs[i].len);
- if (!msgs[i].len) { /* no len: check only for device presence */
+ if (!msgs[i].len) {
+ /* no len: check only for device presence */
rc = cx231xx_i2c_check_for_device(i2c_adap, &msgs[i]);
if (rc < 0) {
dprintk2(2, " no device\n");
@@ -409,7 +413,7 @@
}
return num;
- err:
+err:
dprintk2(2, " ERROR: %i\n", rc);
return rc;
}