ARM: OMAP: Remove old dead gpio expander code
This should be done with GPIO calls. Patches against the
mainline tree welcome to add the necessary working functionality
back.
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap1/board-h3.c b/arch/arm/mach-omap1/board-h3.c
index 4695965..f597968 100644
--- a/arch/arm/mach-omap1/board-h3.c
+++ b/arch/arm/mach-omap1/board-h3.c
@@ -39,12 +39,10 @@
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
-#include <mach/gpioexpander.h>
#include <mach/irqs.h>
#include <mach/mux.h>
#include <mach/tc.h>
#include <mach/nand.h>
-#include <mach/irda.h>
#include <mach/usb.h>
#include <mach/keypad.h>
#include <mach/dma.h>
@@ -276,104 +274,6 @@
.resource = h3_kp_resources,
};
-
-/* Select between the IrDA and aGPS module
- */
-static int h3_select_irda(struct device *dev, int state)
-{
- unsigned char expa;
- int err = 0;
-
- if ((err = read_gpio_expa(&expa, 0x26))) {
- printk(KERN_ERR "Error reading from I/O EXPANDER \n");
- return err;
- }
-
- /* 'P6' enable/disable IRDA_TX and IRDA_RX */
- if (state & IR_SEL) { /* IrDA */
- if ((err = write_gpio_expa(expa | 0x40, 0x26))) {
- printk(KERN_ERR "Error writing to I/O EXPANDER \n");
- return err;
- }
- } else {
- if ((err = write_gpio_expa(expa & ~0x40, 0x26))) {
- printk(KERN_ERR "Error writing to I/O EXPANDER \n");
- return err;
- }
- }
- return err;
-}
-
-static void set_trans_mode(struct work_struct *work)
-{
- struct omap_irda_config *irda_config =
- container_of(work, struct omap_irda_config, gpio_expa.work);
- int mode = irda_config->mode;
- unsigned char expa;
- int err = 0;
-
- if ((err = read_gpio_expa(&expa, 0x27)) != 0) {
- printk(KERN_ERR "Error reading from I/O expander\n");
- }
-
- expa &= ~0x03;
-
- if (mode & IR_SIRMODE) {
- expa |= 0x01;
- } else { /* MIR/FIR */
- expa |= 0x03;
- }
-
- if ((err = write_gpio_expa(expa, 0x27)) != 0) {
- printk(KERN_ERR "Error writing to I/O expander\n");
- }
-}
-
-static int h3_transceiver_mode(struct device *dev, int mode)
-{
- struct omap_irda_config *irda_config = dev->platform_data;
-
- irda_config->mode = mode;
- cancel_delayed_work(&irda_config->gpio_expa);
- PREPARE_DELAYED_WORK(&irda_config->gpio_expa, set_trans_mode);
- schedule_delayed_work(&irda_config->gpio_expa, 0);
-
- return 0;
-}
-
-static struct omap_irda_config h3_irda_data = {
- .transceiver_cap = IR_SIRMODE | IR_MIRMODE | IR_FIRMODE,
- .transceiver_mode = h3_transceiver_mode,
- .select_irda = h3_select_irda,
- .rx_channel = OMAP_DMA_UART3_RX,
- .tx_channel = OMAP_DMA_UART3_TX,
- .dest_start = UART3_THR,
- .src_start = UART3_RHR,
- .tx_trigger = 0,
- .rx_trigger = 0,
-};
-
-static struct resource h3_irda_resources[] = {
- [0] = {
- .start = INT_UART3,
- .end = INT_UART3,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static u64 irda_dmamask = 0xffffffff;
-
-static struct platform_device h3_irda_device = {
- .name = "omapirda",
- .id = 0,
- .dev = {
- .platform_data = &h3_irda_data,
- .dma_mask = &irda_dmamask,
- },
- .num_resources = ARRAY_SIZE(h3_irda_resources),
- .resource = h3_irda_resources,
-};
-
static struct platform_device h3_lcd_device = {
.name = "lcd_h3",
.id = -1,
@@ -395,7 +295,6 @@
&nand_device,
&smc91x_device,
&intlat_device,
- &h3_irda_device,
&h3_kp_device,
&h3_lcd_device,
};
diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c
index a0267a9..e7d017c 100644
--- a/arch/arm/mach-omap2/board-h4.c
+++ b/arch/arm/mach-omap2/board-h4.c
@@ -33,10 +33,8 @@
#include <mach/control.h>
#include <mach/gpio.h>
-#include <mach/gpioexpander.h>
#include <mach/mux.h>
#include <mach/usb.h>
-#include <mach/irda.h>
#include <mach/board.h>
#include <mach/common.h>
#include <mach/keypad.h>
@@ -138,98 +136,6 @@
.resource = &h4_flash_resource,
};
-/* Select between the IrDA and aGPS module
- */
-static int h4_select_irda(struct device *dev, int state)
-{
- unsigned char expa;
- int err = 0;
-
- if ((err = read_gpio_expa(&expa, 0x21))) {
- printk(KERN_ERR "Error reading from I/O expander\n");
- return err;
- }
-
- /* 'P6' enable/disable IRDA_TX and IRDA_RX */
- if (state & IR_SEL) { /* IrDa */
- if ((err = write_gpio_expa(expa | 0x01, 0x21))) {
- printk(KERN_ERR "Error writing to I/O expander\n");
- return err;
- }
- } else {
- if ((err = write_gpio_expa(expa & ~0x01, 0x21))) {
- printk(KERN_ERR "Error writing to I/O expander\n");
- return err;
- }
- }
- return err;
-}
-
-static void set_trans_mode(struct work_struct *work)
-{
- struct omap_irda_config *irda_config =
- container_of(work, struct omap_irda_config, gpio_expa.work);
- int mode = irda_config->mode;
- unsigned char expa;
- int err = 0;
-
- if ((err = read_gpio_expa(&expa, 0x20)) != 0) {
- printk(KERN_ERR "Error reading from I/O expander\n");
- }
-
- expa &= ~0x01;
-
- if (!(mode & IR_SIRMODE)) { /* MIR/FIR */
- expa |= 0x01;
- }
-
- if ((err = write_gpio_expa(expa, 0x20)) != 0) {
- printk(KERN_ERR "Error writing to I/O expander\n");
- }
-}
-
-static int h4_transceiver_mode(struct device *dev, int mode)
-{
- struct omap_irda_config *irda_config = dev->platform_data;
-
- irda_config->mode = mode;
- cancel_delayed_work(&irda_config->gpio_expa);
- PREPARE_DELAYED_WORK(&irda_config->gpio_expa, set_trans_mode);
- schedule_delayed_work(&irda_config->gpio_expa, 0);
-
- return 0;
-}
-
-static struct omap_irda_config h4_irda_data = {
- .transceiver_cap = IR_SIRMODE | IR_MIRMODE | IR_FIRMODE,
- .transceiver_mode = h4_transceiver_mode,
- .select_irda = h4_select_irda,
- .rx_channel = OMAP24XX_DMA_UART3_RX,
- .tx_channel = OMAP24XX_DMA_UART3_TX,
- .dest_start = OMAP_UART3_BASE,
- .src_start = OMAP_UART3_BASE,
- .tx_trigger = OMAP24XX_DMA_UART3_TX,
- .rx_trigger = OMAP24XX_DMA_UART3_RX,
-};
-
-static struct resource h4_irda_resources[] = {
- [0] = {
- .start = INT_24XX_UART3_IRQ,
- .end = INT_24XX_UART3_IRQ,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device h4_irda_device = {
- .name = "omapirda",
- .id = -1,
- .dev = {
- .platform_data = &h4_irda_data,
- },
- .num_resources = 1,
- .resource = h4_irda_resources,
-};
-
static struct omap_kp_platform_data h4_kp_data = {
.rows = 6,
.cols = 7,
@@ -255,7 +161,6 @@
static struct platform_device *h4_devices[] __initdata = {
&h4_flash_device,
- &h4_irda_device,
&h4_kp_device,
&h4_lcd_device,
};
diff --git a/arch/arm/plat-omap/include/mach/gpioexpander.h b/arch/arm/plat-omap/include/mach/gpioexpander.h
deleted file mode 100644
index 90444a0..0000000
--- a/arch/arm/plat-omap/include/mach/gpioexpander.h
+++ /dev/null
@@ -1,35 +0,0 @@
-/*
- * arch/arm/plat-omap/include/mach/gpioexpander.h
- *
- *
- * Copyright (C) 2004 Texas Instruments, Inc.
- *
- * This package is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * THIS PACKAGE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
- * WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE.
- */
-
-#ifndef __ASM_ARCH_OMAP_GPIOEXPANDER_H
-#define __ASM_ARCH_OMAP_GPIOEXPANDER_H
-
-/* Function Prototypes for GPIO Expander functions */
-
-#ifdef CONFIG_GPIOEXPANDER_OMAP
-int read_gpio_expa(u8 *, int);
-int write_gpio_expa(u8 , int);
-#else
-static inline int read_gpio_expa(u8 *val, int addr)
-{
- return 0;
-}
-static inline int write_gpio_expa(u8 val, int addr)
-{
- return 0;
-}
-#endif
-
-#endif /* __ASM_ARCH_OMAP_GPIOEXPANDER_H */
diff --git a/arch/arm/plat-omap/include/mach/irda.h b/arch/arm/plat-omap/include/mach/irda.h
index 8372a00..40f6033 100644
--- a/arch/arm/plat-omap/include/mach/irda.h
+++ b/arch/arm/plat-omap/include/mach/irda.h
@@ -21,10 +21,6 @@
int transceiver_cap;
int (*transceiver_mode)(struct device *dev, int mode);
int (*select_irda)(struct device *dev, int state);
- /* Very specific to the needs of some platforms (h3,h4)
- * having calls which can sleep in irda_set_speed.
- */
- struct delayed_work gpio_expa;
int rx_channel;
int tx_channel;
unsigned long dest_start;