Au1[12]00 mmc driver. Only tested on the Au1200 at this point though
it should work on the Au1100 as well. Updated defconfig to include driver.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
diff --git a/drivers/mmc/au1xmmc.c b/drivers/mmc/au1xmmc.c
new file mode 100644
index 0000000..aaf0463
--- /dev/null
+++ b/drivers/mmc/au1xmmc.c
@@ -0,0 +1,1026 @@
+/*
+ * linux/drivers/mmc/au1xmmc.c - AU1XX0 MMC driver
+ *
+ * Copyright (c) 2005, Advanced Micro Devices, Inc.
+ *
+ * Developed with help from the 2.4.30 MMC AU1XXX controller including
+ * the following copyright notices:
+ * Copyright (c) 2003-2004 Embedded Edge, LLC.
+ * Portions Copyright (C) 2002 Embedix, Inc
+ * Copyright 2002 Hewlett-Packard Company
+
+ * 2.6 version of this driver inspired by:
+ * (drivers/mmc/wbsd.c) Copyright (C) 2004-2005 Pierre Ossman,
+ * All Rights Reserved.
+ * (drivers/mmc/pxa.c) Copyright (C) 2003 Russell King,
+ * All Rights Reserved.
+ *
+
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/* Why is a timer used to detect insert events?
+ *
+ * From the AU1100 MMC application guide:
+ * If the Au1100-based design is intended to support both MultiMediaCards
+ * and 1- or 4-data bit SecureDigital cards, then the solution is to
+ * connect a weak (560KOhm) pull-up resistor to connector pin 1.
+ * In doing so, a MMC card never enters SPI-mode communications,
+ * but now the SecureDigital card-detect feature of CD/DAT3 is ineffective
+ * (the low to high transition will not occur).
+ *
+ * So we use the timer to check the status manually.
+ */
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/mm.h>
+#include <linux/interrupt.h>
+#include <linux/dma-mapping.h>
+
+#include <linux/mmc/host.h>
+#include <linux/mmc/protocol.h>
+#include <asm/io.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/scatterlist.h>
+
+#include <au1xxx.h>
+#include "au1xmmc.h"
+
+#define DRIVER_NAME "au1xxx-mmc"
+
+/* Set this to enable special debugging macros */
+/* #define MMC_DEBUG */
+
+#ifdef MMC_DEBUG
+#define DEBUG(fmt, idx, args...) printk("au1xx(%d): DEBUG: " fmt, idx, ##args)
+#else
+#define DEBUG(fmt, idx, args...)
+#endif
+
+const struct {
+ u32 iobase;
+ u32 tx_devid, rx_devid;
+ u16 bcsrpwr;
+ u16 bcsrstatus;
+ u16 wpstatus;
+} au1xmmc_card_table[] = {
+ { SD0_BASE, DSCR_CMD0_SDMS_TX0, DSCR_CMD0_SDMS_RX0,
+ BCSR_BOARD_SD0PWR, BCSR_INT_SD0INSERT, BCSR_STATUS_SD0WP },
+#ifndef CONFIG_MIPS_DB1200
+ { SD1_BASE, DSCR_CMD0_SDMS_TX1, DSCR_CMD0_SDMS_RX1,
+ BCSR_BOARD_DS1PWR, BCSR_INT_SD1INSERT, BCSR_STATUS_SD1WP }
+#endif
+};
+
+#define AU1XMMC_CONTROLLER_COUNT \
+ (sizeof(au1xmmc_card_table) / sizeof(au1xmmc_card_table[0]))
+
+/* This array stores pointers for the hosts (used by the IRQ handler) */
+struct au1xmmc_host *au1xmmc_hosts[AU1XMMC_CONTROLLER_COUNT];
+static int dma = 1;
+
+#ifdef MODULE
+MODULE_PARM(dma, "i");
+MODULE_PARM_DESC(dma, "Use DMA engine for data transfers (0 = disabled)");
+#endif
+
+static inline void IRQ_ON(struct au1xmmc_host *host, u32 mask)
+{
+ u32 val = au_readl(HOST_CONFIG(host));
+ val |= mask;
+ au_writel(val, HOST_CONFIG(host));
+ au_sync();
+}
+
+static inline void FLUSH_FIFO(struct au1xmmc_host *host)
+{
+ u32 val = au_readl(HOST_CONFIG2(host));
+
+ au_writel(val | SD_CONFIG2_FF, HOST_CONFIG2(host));
+ au_sync_delay(1);
+
+ /* SEND_STOP will turn off clock control - this re-enables it */
+ val &= ~SD_CONFIG2_DF;
+
+ au_writel(val, HOST_CONFIG2(host));
+ au_sync();
+}
+
+static inline void IRQ_OFF(struct au1xmmc_host *host, u32 mask)
+{
+ u32 val = au_readl(HOST_CONFIG(host));
+ val &= ~mask;
+ au_writel(val, HOST_CONFIG(host));
+ au_sync();
+}
+
+static inline void SEND_STOP(struct au1xmmc_host *host)
+{
+
+ /* We know the value of CONFIG2, so avoid a read we don't need */
+ u32 mask = SD_CONFIG2_EN;
+
+ WARN_ON(host->status != HOST_S_DATA);
+ host->status = HOST_S_STOP;
+
+ au_writel(mask | SD_CONFIG2_DF, HOST_CONFIG2(host));
+ au_sync();
+
+ /* Send the stop commmand */
+ au_writel(STOP_CMD, HOST_CMD(host));
+}
+
+static void au1xmmc_set_power(struct au1xmmc_host *host, int state)
+{
+
+ u32 val = au1xmmc_card_table[host->id].bcsrpwr;
+
+ bcsr->board &= ~val;
+ if (state) bcsr->board |= val;
+
+ au_sync_delay(1);
+}
+
+static inline int au1xmmc_card_inserted(struct au1xmmc_host *host)
+{
+ return (bcsr->sig_status & au1xmmc_card_table[host->id].bcsrstatus)
+ ? 1 : 0;
+}
+
+static inline int au1xmmc_card_readonly(struct au1xmmc_host *host)
+{
+ return (bcsr->status & au1xmmc_card_table[host->id].wpstatus)
+ ? 1 : 0;
+}
+
+static void au1xmmc_finish_request(struct au1xmmc_host *host)
+{
+
+ struct mmc_request *mrq = host->mrq;
+
+ host->mrq = NULL;
+ host->flags &= HOST_F_ACTIVE;
+
+ host->dma.len = 0;
+ host->dma.dir = 0;
+
+ host->pio.index = 0;
+ host->pio.offset = 0;
+ host->pio.len = 0;
+
+ host->status = HOST_S_IDLE;
+
+ bcsr->disk_leds |= (1 << 8);
+
+ mmc_request_done(host->mmc, mrq);
+}
+
+static void au1xmmc_tasklet_finish(unsigned long param)
+{
+ struct au1xmmc_host *host = (struct au1xmmc_host *) param;
+ au1xmmc_finish_request(host);
+}
+
+static int au1xmmc_send_command(struct au1xmmc_host *host, int wait,
+ struct mmc_command *cmd)
+{
+
+ u32 mmccmd = (cmd->opcode << SD_CMD_CI_SHIFT);
+
+ switch(cmd->flags) {
+ case MMC_RSP_R1:
+ mmccmd |= SD_CMD_RT_1;
+ break;
+ case MMC_RSP_R1B:
+ mmccmd |= SD_CMD_RT_1B;
+ break;
+ case MMC_RSP_R2:
+ mmccmd |= SD_CMD_RT_2;
+ break;
+ case MMC_RSP_R3:
+ mmccmd |= SD_CMD_RT_3;
+ break;
+ }
+
+ switch(cmd->opcode) {
+ case MMC_READ_SINGLE_BLOCK:
+ case SD_APP_SEND_SCR:
+ mmccmd |= SD_CMD_CT_2;
+ break;
+ case MMC_READ_MULTIPLE_BLOCK:
+ mmccmd |= SD_CMD_CT_4;
+ break;
+ case MMC_WRITE_BLOCK:
+ mmccmd |= SD_CMD_CT_1;
+ break;
+
+ case MMC_WRITE_MULTIPLE_BLOCK:
+ mmccmd |= SD_CMD_CT_3;
+ break;
+ case MMC_STOP_TRANSMISSION:
+ mmccmd |= SD_CMD_CT_7;
+ break;
+ }
+
+ au_writel(cmd->arg, HOST_CMDARG(host));
+ au_sync();
+
+ if (wait)
+ IRQ_OFF(host, SD_CONFIG_CR);
+
+ au_writel((mmccmd | SD_CMD_GO), HOST_CMD(host));
+ au_sync();
+
+ /* Wait for the command to go on the line */
+
+ while(1) {
+ if (!(au_readl(HOST_CMD(host)) & SD_CMD_GO))
+ break;
+ }
+
+ /* Wait for the command to come back */
+
+ if (wait) {
+ u32 status = au_readl(HOST_STATUS(host));
+
+ while(!(status & SD_STATUS_CR))
+ status = au_readl(HOST_STATUS(host));
+
+ /* Clear the CR status */
+ au_writel(SD_STATUS_CR, HOST_STATUS(host));
+
+ IRQ_ON(host, SD_CONFIG_CR);
+ }
+
+ return MMC_ERR_NONE;
+}
+
+static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status)
+{
+
+ struct mmc_request *mrq = host->mrq;
+ struct mmc_data *data;
+ u32 crc;
+
+ WARN_ON(host->status != HOST_S_DATA && host->status != HOST_S_STOP);
+
+ if (host->mrq == NULL)
+ return;
+
+ data = mrq->cmd->data;
+
+ if (status == 0)
+ status = au_readl(HOST_STATUS(host));
+
+ /* The transaction is really over when the SD_STATUS_DB bit is clear */
+
+ while((host->flags & HOST_F_XMIT) && (status & SD_STATUS_DB))
+ status = au_readl(HOST_STATUS(host));
+
+ data->error = MMC_ERR_NONE;
+ dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, host->dma.dir);
+
+ /* Process any errors */
+
+ crc = (status & (SD_STATUS_WC | SD_STATUS_RC));
+ if (host->flags & HOST_F_XMIT)
+ crc |= ((status & 0x07) == 0x02) ? 0 : 1;
+
+ if (crc)
+ data->error = MMC_ERR_BADCRC;
+
+ /* Clear the CRC bits */
+ au_writel(SD_STATUS_WC | SD_STATUS_RC, HOST_STATUS(host));
+
+ data->bytes_xfered = 0;
+
+ if (data->error == MMC_ERR_NONE) {
+ if (host->flags & HOST_F_DMA) {
+ u32 chan = DMA_CHANNEL(host);
+
+ chan_tab_t *c = *((chan_tab_t **) chan);
+ au1x_dma_chan_t *cp = c->chan_ptr;
+ data->bytes_xfered = cp->ddma_bytecnt;
+ }
+ else
+ data->bytes_xfered =
+ (data->blocks * (1 << data->blksz_bits)) -
+ host->pio.len;
+ }
+
+ au1xmmc_finish_request(host);
+}
+
+static void au1xmmc_tasklet_data(unsigned long param)
+{
+ struct au1xmmc_host *host = (struct au1xmmc_host *) param;
+
+ u32 status = au_readl(HOST_STATUS(host));
+ au1xmmc_data_complete(host, status);
+}
+
+#define AU1XMMC_MAX_TRANSFER 8
+
+static void au1xmmc_send_pio(struct au1xmmc_host *host)
+{
+
+ struct mmc_data *data = 0;
+ int sg_len, max, count = 0;
+ unsigned char *sg_ptr;
+ u32 status = 0;
+ struct scatterlist *sg;
+
+ data = host->mrq->data;
+
+ if (!(host->flags & HOST_F_XMIT))
+ return;
+
+ /* This is the pointer to the data buffer */
+ sg = &data->sg[host->pio.index];
+ sg_ptr = page_address(sg->page) + sg->offset + host->pio.offset;
+
+ /* This is the space left inside the buffer */
+ sg_len = data->sg[host->pio.index].length - host->pio.offset;
+
+ /* Check to if we need less then the size of the sg_buffer */
+
+ max = (sg_len > host->pio.len) ? host->pio.len : sg_len;
+ if (max > AU1XMMC_MAX_TRANSFER) max = AU1XMMC_MAX_TRANSFER;
+
+ for(count = 0; count < max; count++ ) {
+ unsigned char val;
+
+ status = au_readl(HOST_STATUS(host));
+
+ if (!(status & SD_STATUS_TH))
+ break;
+
+ val = *sg_ptr++;
+
+ au_writel((unsigned long) val, HOST_TXPORT(host));
+ au_sync();
+ }
+
+ host->pio.len -= count;
+ host->pio.offset += count;
+
+ if (count == sg_len) {
+ host->pio.index++;
+ host->pio.offset = 0;
+ }
+
+ if (host->pio.len == 0) {
+ IRQ_OFF(host, SD_CONFIG_TH);
+
+ if (host->flags & HOST_F_STOP)
+ SEND_STOP(host);
+
+ tasklet_schedule(&host->data_task);
+ }
+}
+
+static void au1xmmc_receive_pio(struct au1xmmc_host *host)
+{
+
+ struct mmc_data *data = 0;
+ int sg_len = 0, max = 0, count = 0;
+ unsigned char *sg_ptr = 0;
+ u32 status = 0;
+ struct scatterlist *sg;
+
+ data = host->mrq->data;
+
+ if (!(host->flags & HOST_F_RECV))
+ return;
+
+ max = host->pio.len;
+
+ if (host->pio.index < host->dma.len) {
+ sg = &data->sg[host->pio.index];
+ sg_ptr = page_address(sg->page) + sg->offset + host->pio.offset;
+
+ /* This is the space left inside the buffer */
+ sg_len = sg_dma_len(&data->sg[host->pio.index]) - host->pio.offset;
+
+ /* Check to if we need less then the size of the sg_buffer */
+ if (sg_len < max) max = sg_len;
+ }
+
+ if (max > AU1XMMC_MAX_TRANSFER)
+ max = AU1XMMC_MAX_TRANSFER;
+
+ for(count = 0; count < max; count++ ) {
+ u32 val;
+ status = au_readl(HOST_STATUS(host));
+
+ if (!(status & SD_STATUS_NE))
+ break;
+
+ if (status & SD_STATUS_RC) {
+ DEBUG("RX CRC Error [%d + %d].\n", host->id,
+ host->pio.len, count);
+ break;
+ }
+
+ if (status & SD_STATUS_RO) {
+ DEBUG("RX Overrun [%d + %d]\n", host->id,
+ host->pio.len, count);
+ break;
+ }
+ else if (status & SD_STATUS_RU) {
+ DEBUG("RX Underrun [%d + %d]\n", host->id,
+ host->pio.len, count);
+ break;
+ }
+
+ val = au_readl(HOST_RXPORT(host));
+
+ if (sg_ptr)
+ *sg_ptr++ = (unsigned char) (val & 0xFF);
+ }
+
+ host->pio.len -= count;
+ host->pio.offset += count;
+
+ if (sg_len && count == sg_len) {
+ host->pio.index++;
+ host->pio.offset = 0;
+ }
+
+ if (host->pio.len == 0) {
+ //IRQ_OFF(host, SD_CONFIG_RA | SD_CONFIG_RF);
+ IRQ_OFF(host, SD_CONFIG_NE);
+
+ if (host->flags & HOST_F_STOP)
+ SEND_STOP(host);
+
+ tasklet_schedule(&host->data_task);
+ }
+}
+
+/* static void au1xmmc_cmd_complete
+ This is called when a command has been completed - grab the response
+ and check for errors. Then start the data transfer if it is indicated.
+*/
+
+static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status)
+{
+
+ struct mmc_request *mrq = host->mrq;
+ struct mmc_command *cmd;
+ int trans;
+
+ if (!host->mrq)
+ return;
+
+ cmd = mrq->cmd;
+ cmd->error = MMC_ERR_NONE;
+
+ if ((cmd->flags & MMC_RSP_MASK) == MMC_RSP_SHORT) {
+
+ /* Techincally, we should be getting all 48 bits of the response
+ * (SD_RESP1 + SD_RESP2), but because our response omits the CRC,
+ * our data ends up being shifted 8 bits to the right. In this case,
+ * that means that the OSR data starts at bit 31, so we can just
+ * read RESP0 and return that
+ */
+
+ cmd->resp[0] = au_readl(host->iobase + SD_RESP0);
+ }
+ else if ((cmd->flags & MMC_RSP_MASK) == MMC_RSP_LONG) {
+ u32 r[4];
+ int i;
+
+ r[0] = au_readl(host->iobase + SD_RESP3);
+ r[1] = au_readl(host->iobase + SD_RESP2);
+ r[2] = au_readl(host->iobase + SD_RESP1);
+ r[3] = au_readl(host->iobase + SD_RESP0);
+
+ /* The CRC is omitted from the response, so really we only got
+ * 120 bytes, but the engine expects 128 bits, so we have to shift
+ * things up
+ */
+
+ for(i = 0; i < 4; i++) {
+ cmd->resp[i] = (r[i] & 0x00FFFFFF) << 8;
+ if (i != 3) cmd->resp[i] |= (r[i + 1] & 0xFF000000) >> 24;
+ }
+ }
+
+ /* Figure out errors */
+
+ if (status & (SD_STATUS_SC | SD_STATUS_WC | SD_STATUS_RC))
+ cmd->error = MMC_ERR_BADCRC;
+
+ trans = host->flags & (HOST_F_XMIT | HOST_F_RECV);
+
+ if (!trans || cmd->error != MMC_ERR_NONE) {
+
+ IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA|SD_CONFIG_RF);
+ tasklet_schedule(&host->finish_task);
+ return;
+ }
+
+ host->status = HOST_S_DATA;
+
+ if (host->flags & HOST_F_DMA) {
+ u32 channel = DMA_CHANNEL(host);
+
+ /* Start the DMA as soon as the buffer gets something in it */
+
+ if (host->flags & HOST_F_RECV) {
+ u32 mask = SD_STATUS_DB | SD_STATUS_NE;
+
+ while((status & mask) != mask)
+ status = au_readl(HOST_STATUS(host));
+ }
+
+ au1xxx_dbdma_start(channel);
+ }
+}
+
+static void au1xmmc_set_clock(struct au1xmmc_host *host, int rate)
+{
+
+ unsigned int pbus = get_au1x00_speed();
+ unsigned int divisor;
+ u32 config;
+
+ /* From databook:
+ divisor = ((((cpuclock / sbus_divisor) / 2) / mmcclock) / 2) - 1
+ */
+
+ pbus /= ((au_readl(SYS_POWERCTRL) & 0x3) + 2);
+ pbus /= 2;
+
+ divisor = ((pbus / rate) / 2) - 1;
+
+ config = au_readl(HOST_CONFIG(host));
+
+ config &= ~(SD_CONFIG_DIV);
+ config |= (divisor & SD_CONFIG_DIV) | SD_CONFIG_DE;
+
+ au_writel(config, HOST_CONFIG(host));
+ au_sync();
+}
+
+static int
+au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data)
+{
+
+ int datalen = data->blocks * (1 << data->blksz_bits);
+
+ if (dma != 0)
+ host->flags |= HOST_F_DMA;
+
+ if (data->flags & MMC_DATA_READ)
+ host->flags |= HOST_F_RECV;
+ else
+ host->flags |= HOST_F_XMIT;
+
+ if (host->mrq->stop)
+ host->flags |= HOST_F_STOP;
+
+ host->dma.dir = DMA_BIDIRECTIONAL;
+
+ host->dma.len = dma_map_sg(mmc_dev(host->mmc), data->sg,
+ data->sg_len, host->dma.dir);
+
+ if (host->dma.len == 0)
+ return MMC_ERR_TIMEOUT;
+
+ au_writel((1 << data->blksz_bits) - 1, HOST_BLKSIZE(host));
+
+ if (host->flags & HOST_F_DMA) {
+ int i;
+ u32 channel = DMA_CHANNEL(host);
+
+ au1xxx_dbdma_stop(channel);
+
+ for(i = 0; i < host->dma.len; i++) {
+ u32 ret = 0, flags = DDMA_FLAGS_NOIE;
+ struct scatterlist *sg = &data->sg[i];
+ int sg_len = sg->length;
+
+ int len = (datalen > sg_len) ? sg_len : datalen;
+
+ if (i == host->dma.len - 1)
+ flags = DDMA_FLAGS_IE;
+
+ if (host->flags & HOST_F_XMIT){
+ ret = au1xxx_dbdma_put_source_flags(channel,
+ (void *) (page_address(sg->page) +
+ sg->offset),
+ len, flags);
+ }
+ else {
+ ret = au1xxx_dbdma_put_dest_flags(channel,
+ (void *) (page_address(sg->page) +
+ sg->offset),
+ len, flags);
+ }
+
+ if (!ret)
+ goto dataerr;
+
+ datalen -= len;
+ }
+ }
+ else {
+ host->pio.index = 0;
+ host->pio.offset = 0;
+ host->pio.len = datalen;
+
+ if (host->flags & HOST_F_XMIT)
+ IRQ_ON(host, SD_CONFIG_TH);
+ else
+ IRQ_ON(host, SD_CONFIG_NE);
+ //IRQ_ON(host, SD_CONFIG_RA|SD_CONFIG_RF);
+ }
+
+ return MMC_ERR_NONE;
+
+ dataerr:
+ dma_unmap_sg(mmc_dev(host->mmc),data->sg,data->sg_len,host->dma.dir);
+ return MMC_ERR_TIMEOUT;
+}
+
+/* static void au1xmmc_request
+ This actually starts a command or data transaction
+*/
+
+static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq)
+{
+
+ struct au1xmmc_host *host = mmc_priv(mmc);
+ int ret = MMC_ERR_NONE;
+
+ WARN_ON(irqs_disabled());
+ WARN_ON(host->status != HOST_S_IDLE);
+
+ host->mrq = mrq;
+ host->status = HOST_S_CMD;
+
+ bcsr->disk_leds &= ~(1 << 8);
+
+ if (mrq->data) {
+ FLUSH_FIFO(host);
+ ret = au1xmmc_prepare_data(host, mrq->data);
+ }
+
+ if (ret == MMC_ERR_NONE)
+ ret = au1xmmc_send_command(host, 0, mrq->cmd);
+
+ if (ret != MMC_ERR_NONE) {
+ mrq->cmd->error = ret;
+ au1xmmc_finish_request(host);
+ }
+}
+
+static void au1xmmc_reset_controller(struct au1xmmc_host *host)
+{
+
+ /* Apply the clock */
+ au_writel(SD_ENABLE_CE, HOST_ENABLE(host));
+ au_sync_delay(1);
+
+ au_writel(SD_ENABLE_R | SD_ENABLE_CE, HOST_ENABLE(host));
+ au_sync_delay(5);
+
+ au_writel(~0, HOST_STATUS(host));
+ au_sync();
+
+ au_writel(0, HOST_BLKSIZE(host));
+ au_writel(0x001fffff, HOST_TIMEOUT(host));
+ au_sync();
+
+ au_writel(SD_CONFIG2_EN, HOST_CONFIG2(host));
+ au_sync();
+
+ au_writel(SD_CONFIG2_EN | SD_CONFIG2_FF, HOST_CONFIG2(host));
+ au_sync_delay(1);
+
+ au_writel(SD_CONFIG2_EN, HOST_CONFIG2(host));
+ au_sync();
+
+ /* Configure interrupts */
+ au_writel(AU1XMMC_INTERRUPTS, HOST_CONFIG(host));
+ au_sync();
+}
+
+
+static void au1xmmc_set_ios(struct mmc_host* mmc, struct mmc_ios* ios)
+{
+ struct au1xmmc_host *host = mmc_priv(mmc);
+
+ DEBUG("set_ios (power=%u, clock=%uHz, vdd=%u, mode=%u)\n",
+ host->id, ios->power_mode, ios->clock, ios->vdd,
+ ios->bus_mode);
+
+ if (ios->power_mode == MMC_POWER_OFF)
+ au1xmmc_set_power(host, 0);
+ else if (ios->power_mode == MMC_POWER_ON) {
+ au1xmmc_set_power(host, 1);
+ }
+
+ if (ios->clock && ios->clock != host->clock) {
+ au1xmmc_set_clock(host, ios->clock);
+ host->clock = ios->clock;
+ }
+}
+
+static void au1xmmc_dma_callback(int irq, void *dev_id, struct pt_regs *regs)
+{
+ struct au1xmmc_host *host = (struct au1xmmc_host *) dev_id;
+ u32 status;
+
+ /* Avoid spurious interrupts */
+
+ if (!host->mrq)
+ return;
+
+ if (host->flags & HOST_F_STOP)
+ SEND_STOP(host);
+
+ tasklet_schedule(&host->data_task);
+}
+
+#define STATUS_TIMEOUT (SD_STATUS_RAT | SD_STATUS_DT)
+#define STATUS_DATA_IN (SD_STATUS_NE)
+#define STATUS_DATA_OUT (SD_STATUS_TH)
+
+static irqreturn_t au1xmmc_irq(int irq, void *dev_id, struct pt_regs *regs)
+{
+
+ u32 status;
+ int i, ret = 0;
+
+ disable_irq(AU1100_SD_IRQ);
+
+ for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) {
+ struct au1xmmc_host * host = au1xmmc_hosts[i];
+ u32 handled = 1;
+
+ status = au_readl(HOST_STATUS(host));
+
+ if (host->mrq && (status & STATUS_TIMEOUT)) {
+ if (status & SD_STATUS_RAT)
+ host->mrq->cmd->error = MMC_ERR_TIMEOUT;
+
+ else if (status & SD_STATUS_DT)
+ host->mrq->data->error = MMC_ERR_TIMEOUT;
+
+ /* In PIO mode, interrupts might still be enabled */
+ IRQ_OFF(host, SD_CONFIG_NE | SD_CONFIG_TH);
+
+ //IRQ_OFF(host, SD_CONFIG_TH|SD_CONFIG_RA|SD_CONFIG_RF);
+ tasklet_schedule(&host->finish_task);
+ }
+#if 0
+ else if (status & SD_STATUS_DD) {
+
+ /* Sometimes we get a DD before a NE in PIO mode */
+
+ if (!(host->flags & HOST_F_DMA) &&
+ (status & SD_STATUS_NE))
+ au1xmmc_receive_pio(host);
+ else {
+ au1xmmc_data_complete(host, status);
+ //tasklet_schedule(&host->data_task);
+ }
+ }
+#endif
+ else if (status & (SD_STATUS_CR)) {
+ if (host->status == HOST_S_CMD)
+ au1xmmc_cmd_complete(host,status);
+ }
+ else if (!(host->flags & HOST_F_DMA)) {
+ if ((host->flags & HOST_F_XMIT) &&
+ (status & STATUS_DATA_OUT))
+ au1xmmc_send_pio(host);
+ else if ((host->flags & HOST_F_RECV) &&
+ (status & STATUS_DATA_IN))
+ au1xmmc_receive_pio(host);
+ }
+ else if (status & 0x203FBC70) {
+ DEBUG("Unhandled status %8.8x\n", host->id, status);
+ handled = 0;
+ }
+
+ au_writel(status, HOST_STATUS(host));
+ au_sync();
+
+ ret |= handled;
+ }
+
+ enable_irq(AU1100_SD_IRQ);
+ return ret;
+}
+
+static void au1xmmc_poll_event(unsigned long arg)
+{
+ struct au1xmmc_host *host = (struct au1xmmc_host *) arg;
+
+ int card = au1xmmc_card_inserted(host);
+ int controller = (host->flags & HOST_F_ACTIVE) ? 1 : 0;
+
+ if (card != controller) {
+ host->flags &= ~HOST_F_ACTIVE;
+ if (card) host->flags |= HOST_F_ACTIVE;
+ mmc_detect_change(host->mmc, 0);
+ }
+
+ if (host->mrq != NULL) {
+ u32 status = au_readl(HOST_STATUS(host));
+ DEBUG("PENDING - %8.8x\n", host->id, status);
+ }
+
+ mod_timer(&host->timer, jiffies + AU1XMMC_DETECT_TIMEOUT);
+}
+
+static dbdev_tab_t au1xmmc_mem_dbdev =
+{
+ DSCR_CMD0_ALWAYS, DEV_FLAGS_ANYUSE, 0, 8, 0x00000000, 0, 0
+};
+
+static void au1xmmc_init_dma(struct au1xmmc_host *host)
+{
+
+ u32 rxchan, txchan;
+
+ int txid = au1xmmc_card_table[host->id].tx_devid;
+ int rxid = au1xmmc_card_table[host->id].rx_devid;
+
+ /* DSCR_CMD0_ALWAYS has a stride of 32 bits, we need a stride
+ of 8 bits. And since devices are shared, we need to create
+ our own to avoid freaking out other devices
+ */
+
+ int memid = au1xxx_ddma_add_device(&au1xmmc_mem_dbdev);
+
+ txchan = au1xxx_dbdma_chan_alloc(memid, txid,
+ au1xmmc_dma_callback, (void *) host);
+
+ rxchan = au1xxx_dbdma_chan_alloc(rxid, memid,
+ au1xmmc_dma_callback, (void *) host);
+
+ au1xxx_dbdma_set_devwidth(txchan, 8);
+ au1xxx_dbdma_set_devwidth(rxchan, 8);
+
+ au1xxx_dbdma_ring_alloc(txchan, AU1XMMC_DESCRIPTOR_COUNT);
+ au1xxx_dbdma_ring_alloc(rxchan, AU1XMMC_DESCRIPTOR_COUNT);
+
+ host->tx_chan = txchan;
+ host->rx_chan = rxchan;
+}
+
+struct mmc_host_ops au1xmmc_ops = {
+ .request = au1xmmc_request,
+ .set_ios = au1xmmc_set_ios,
+};
+
+static int au1xmmc_probe(struct device *dev)
+{
+
+ int i, ret = 0;
+
+ /* THe interrupt is shared among all controllers */
+ ret = request_irq(AU1100_SD_IRQ, au1xmmc_irq, SA_INTERRUPT, "MMC", 0);
+
+ if (ret) {
+ printk(DRIVER_NAME "ERROR: Couldn't get int %d: %d\n",
+ AU1100_SD_IRQ, ret);
+ return -ENXIO;
+ }
+
+ disable_irq(AU1100_SD_IRQ);
+
+ for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) {
+ struct mmc_host *mmc = mmc_alloc_host(sizeof(struct au1xmmc_host), dev);
+ struct au1xmmc_host *host = 0;
+
+ if (!mmc) {
+ printk(DRIVER_NAME "ERROR: no mem for host %d\n", i);
+ au1xmmc_hosts[i] = 0;
+ continue;
+ }
+
+ mmc->ops = &au1xmmc_ops;
+
+ mmc->f_min = 450000;
+ mmc->f_max = 24000000;
+
+ mmc->max_seg_size = AU1XMMC_DESCRIPTOR_SIZE;
+ mmc->max_phys_segs = AU1XMMC_DESCRIPTOR_COUNT;
+
+ mmc->ocr_avail = AU1XMMC_OCR;
+
+ host = mmc_priv(mmc);
+ host->mmc = mmc;
+
+ host->id = i;
+ host->iobase = au1xmmc_card_table[host->id].iobase;
+ host->clock = 0;
+ host->power_mode = MMC_POWER_OFF;
+
+ host->flags = au1xmmc_card_inserted(host) ? HOST_F_ACTIVE : 0;
+ host->status = HOST_S_IDLE;
+
+ init_timer(&host->timer);
+
+ host->timer.function = au1xmmc_poll_event;
+ host->timer.data = (unsigned long) host;
+ host->timer.expires = jiffies + AU1XMMC_DETECT_TIMEOUT;
+
+ tasklet_init(&host->data_task, au1xmmc_tasklet_data,
+ (unsigned long) host);
+
+ tasklet_init(&host->finish_task, au1xmmc_tasklet_finish,
+ (unsigned long) host);
+
+ spin_lock_init(&host->lock);
+
+ if (dma != 0)
+ au1xmmc_init_dma(host);
+
+ au1xmmc_reset_controller(host);
+
+ mmc_add_host(mmc);
+ au1xmmc_hosts[i] = host;
+
+ add_timer(&host->timer);
+
+ printk(KERN_INFO DRIVER_NAME ": MMC Controller %d set up at %8.8X (mode=%s)\n",
+ host->id, host->iobase, dma ? "dma" : "pio");
+ }
+
+ enable_irq(AU1100_SD_IRQ);
+
+ return 0;
+}
+
+static int au1xmmc_remove(struct device *dev)
+{
+
+ int i;
+
+ disable_irq(AU1100_SD_IRQ);
+
+ for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) {
+ struct au1xmmc_host *host = au1xmmc_hosts[i];
+ if (!host) continue;
+
+ tasklet_kill(&host->data_task);
+ tasklet_kill(&host->finish_task);
+
+ del_timer_sync(&host->timer);
+ au1xmmc_set_power(host, 0);
+
+ mmc_remove_host(host->mmc);
+
+ au1xxx_dbdma_chan_free(host->tx_chan);
+ au1xxx_dbdma_chan_free(host->rx_chan);
+
+ au_writel(0x0, HOST_ENABLE(host));
+ au_sync();
+ }
+
+ free_irq(AU1100_SD_IRQ, 0);
+ return 0;
+}
+
+static struct device_driver au1xmmc_driver = {
+ .name = DRIVER_NAME,
+ .bus = &platform_bus_type,
+ .probe = au1xmmc_probe,
+ .remove = au1xmmc_remove,
+ .suspend = NULL,
+ .resume = NULL
+};
+
+static int __init au1xmmc_init(void)
+{
+ return driver_register(&au1xmmc_driver);
+}
+
+static void __exit au1xmmc_exit(void)
+{
+ driver_unregister(&au1xmmc_driver);
+}
+
+module_init(au1xmmc_init);
+module_exit(au1xmmc_exit);
+
+#ifdef MODULE
+MODULE_AUTHOR("Advanced Micro Devices, Inc");
+MODULE_DESCRIPTION("MMC/SD driver for the Alchemy Au1XXX");
+MODULE_LICENSE("GPL");
+#endif
+