Au1[12]00 mmc driver. Only tested on the Au1200 at this point though
it should work on the Au1100 as well. Updated defconfig to include driver.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
diff --git a/drivers/mmc/au1xmmc.h b/drivers/mmc/au1xmmc.h
new file mode 100644
index 0000000..341cbdf
--- /dev/null
+++ b/drivers/mmc/au1xmmc.h
@@ -0,0 +1,96 @@
+#ifndef _AU1XMMC_H_
+#define _AU1XMMC_H_
+
+/* Hardware definitions */
+
+#define AU1XMMC_DESCRIPTOR_COUNT 1
+#define AU1XMMC_DESCRIPTOR_SIZE 2048
+
+#define AU1XMMC_OCR ( MMC_VDD_27_28 | MMC_VDD_28_29 | MMC_VDD_29_30 | \
+ MMC_VDD_30_31 | MMC_VDD_31_32 | MMC_VDD_32_33 | \
+ MMC_VDD_33_34 | MMC_VDD_34_35 | MMC_VDD_35_36)
+
+/* Easy access macros */
+
+#define HOST_STATUS(h) ((h)->iobase + SD_STATUS)
+#define HOST_CONFIG(h) ((h)->iobase + SD_CONFIG)
+#define HOST_ENABLE(h) ((h)->iobase + SD_ENABLE)
+#define HOST_TXPORT(h) ((h)->iobase + SD_TXPORT)
+#define HOST_RXPORT(h) ((h)->iobase + SD_RXPORT)
+#define HOST_CMDARG(h) ((h)->iobase + SD_CMDARG)
+#define HOST_BLKSIZE(h) ((h)->iobase + SD_BLKSIZE)
+#define HOST_CMD(h) ((h)->iobase + SD_CMD)
+#define HOST_CONFIG2(h) ((h)->iobase + SD_CONFIG2)
+#define HOST_TIMEOUT(h) ((h)->iobase + SD_TIMEOUT)
+#define HOST_DEBUG(h) ((h)->iobase + SD_DEBUG)
+
+#define DMA_CHANNEL(h) \
+ ( ((h)->flags & HOST_F_XMIT) ? (h)->tx_chan : (h)->rx_chan)
+
+/* This gives us a hard value for the stop command that we can write directly
+ * to the command register
+ */
+
+#define STOP_CMD (SD_CMD_RT_1B|SD_CMD_CT_7|(0xC << SD_CMD_CI_SHIFT)|SD_CMD_GO)
+
+/* This is the set of interrupts that we configure by default */
+
+#if 0
+#define AU1XMMC_INTERRUPTS (SD_CONFIG_SC | SD_CONFIG_DT | SD_CONFIG_DD | \
+ SD_CONFIG_RAT | SD_CONFIG_CR | SD_CONFIG_I)
+#endif
+
+#define AU1XMMC_INTERRUPTS (SD_CONFIG_SC | SD_CONFIG_DT | \
+ SD_CONFIG_RAT | SD_CONFIG_CR | SD_CONFIG_I)
+/* The poll event (looking for insert/remove events runs twice a second */
+#define AU1XMMC_DETECT_TIMEOUT (HZ/2)
+
+struct au1xmmc_host {
+ struct mmc_host *mmc;
+ struct mmc_request *mrq;
+
+ u32 id;
+
+ u32 flags;
+ u32 iobase;
+ u32 clock;
+ u32 bus_width;
+ u32 power_mode;
+
+ int status;
+
+ struct {
+ int len;
+ int dir;
+ } dma;
+
+ struct {
+ int index;
+ int offset;
+ int len;
+ } pio;
+
+ u32 tx_chan;
+ u32 rx_chan;
+
+ struct timer_list timer;
+ struct tasklet_struct finish_task;
+ struct tasklet_struct data_task;
+
+ spinlock_t lock;
+};
+
+/* Status flags used by the host structure */
+
+#define HOST_F_XMIT 0x0001
+#define HOST_F_RECV 0x0002
+#define HOST_F_DMA 0x0010
+#define HOST_F_ACTIVE 0x0100
+#define HOST_F_STOP 0x1000
+
+#define HOST_S_IDLE 0x0001
+#define HOST_S_CMD 0x0002
+#define HOST_S_DATA 0x0003
+#define HOST_S_STOP 0x0004
+
+#endif