ixgb: add explicit state checking
In order to remove the irq_sem code we need to implement strict
adapter state checking to prevent accidental double up or downs
or resets. This code is largely copied from e1000/e1000e.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/net/ixgb/ixgb_main.c b/drivers/net/ixgb/ixgb_main.c
index 269e6f8..548c248 100644
--- a/drivers/net/ixgb/ixgb_main.c
+++ b/drivers/net/ixgb/ixgb_main.c
@@ -283,13 +283,15 @@
}
}
- mod_timer(&adapter->watchdog_timer, jiffies);
+ clear_bit(__IXGB_DOWN, &adapter->flags);
#ifdef CONFIG_IXGB_NAPI
napi_enable(&adapter->napi);
#endif
ixgb_irq_enable(adapter);
+ mod_timer(&adapter->watchdog_timer, jiffies);
+
return 0;
}
@@ -298,11 +300,14 @@
{
struct net_device *netdev = adapter->netdev;
+ /* prevent the interrupt handler from restarting watchdog */
+ set_bit(__IXGB_DOWN, &adapter->flags);
+
#ifdef CONFIG_IXGB_NAPI
napi_disable(&adapter->napi);
atomic_set(&adapter->irq_sem, 0);
#endif
-
+ /* waiting for NAPI to complete can re-enable interrupts */
ixgb_irq_disable(adapter);
free_irq(adapter->pdev->irq, netdev);
@@ -592,6 +597,7 @@
atomic_set(&adapter->irq_sem, 1);
spin_lock_init(&adapter->tx_lock);
+ set_bit(__IXGB_DOWN, &adapter->flags);
return 0;
}
@@ -1464,14 +1470,18 @@
int vlan_id = 0;
int tso;
+ if (test_bit(__IXGB_DOWN, &adapter->flags)) {
+ dev_kfree_skb(skb);
+ return NETDEV_TX_OK;
+ }
+
if(skb->len <= 0) {
dev_kfree_skb_any(skb);
return 0;
}
#ifdef NETIF_F_LLTX
- local_irq_save(flags);
- if (!spin_trylock(&adapter->tx_lock)) {
+ if (!spin_trylock_irqsave(&adapter->tx_lock, flags)) {
/* Collision - tell upper layer to requeue */
local_irq_restore(flags);
return NETDEV_TX_LOCKED;
@@ -1753,9 +1763,9 @@
if(unlikely(!icr))
return IRQ_NONE; /* Not our interrupt */
- if(unlikely(icr & (IXGB_INT_RXSEQ | IXGB_INT_LSC))) {
- mod_timer(&adapter->watchdog_timer, jiffies);
- }
+ if (unlikely(icr & (IXGB_INT_RXSEQ | IXGB_INT_LSC)))
+ if (!test_bit(__IXGB_DOWN, &adapter->flags))
+ mod_timer(&adapter->watchdog_timer, jiffies);
#ifdef CONFIG_IXGB_NAPI
if (netif_rx_schedule_prep(netdev, &adapter->napi)) {
@@ -2195,7 +2205,9 @@
IXGB_WRITE_REG(&adapter->hw, RCTL, rctl);
}
- ixgb_irq_enable(adapter);
+ /* don't enable interrupts unless we are UP */
+ if (adapter->netdev->flags & IFF_UP)
+ ixgb_irq_enable(adapter);
}
static void
@@ -2222,9 +2234,11 @@
vlan_group_set_device(adapter->vlgrp, vid, NULL);
- ixgb_irq_enable(adapter);
+ /* don't enable interrupts unless we are UP */
+ if (adapter->netdev->flags & IFF_UP)
+ ixgb_irq_enable(adapter);
- /* remove VID from filter table*/
+ /* remove VID from filter table */
index = (vid >> 5) & 0x7F;
vfta = IXGB_READ_REG_ARRAY(&adapter->hw, VFTA, index);