| if ARCH_TEGRA |
| |
| comment "NVIDIA Tegra options" |
| |
| config ARCH_TEGRA_2x_SOC |
| bool "Enable support for Tegra20 family" |
| select CPU_V7 |
| select ARM_GIC |
| select ARCH_REQUIRE_GPIOLIB |
| select PINCTRL |
| select PINCTRL_TEGRA20 |
| select USB_ARCH_HAS_EHCI if USB_SUPPORT |
| select USB_ULPI if USB |
| select USB_ULPI_VIEWPORT if USB_SUPPORT |
| select ARM_ERRATA_720789 |
| select ARM_ERRATA_742230 |
| select ARM_ERRATA_751472 |
| select ARM_ERRATA_754327 |
| select ARM_ERRATA_764369 |
| select PL310_ERRATA_727915 if CACHE_L2X0 |
| select PL310_ERRATA_769419 if CACHE_L2X0 |
| select CPU_FREQ_TABLE if CPU_FREQ |
| help |
| Support for NVIDIA Tegra AP20 and T20 processors, based on the |
| ARM CortexA9MP CPU and the ARM PL310 L2 cache controller |
| |
| config ARCH_TEGRA_3x_SOC |
| bool "Enable support for Tegra30 family" |
| select CPU_V7 |
| select ARM_GIC |
| select ARCH_REQUIRE_GPIOLIB |
| select PINCTRL |
| select PINCTRL_TEGRA30 |
| select USB_ARCH_HAS_EHCI if USB_SUPPORT |
| select USB_ULPI if USB |
| select USB_ULPI_VIEWPORT if USB_SUPPORT |
| select ARM_ERRATA_743622 |
| select ARM_ERRATA_751472 |
| select ARM_ERRATA_754322 |
| select ARM_ERRATA_764369 |
| select PL310_ERRATA_769419 if CACHE_L2X0 |
| select CPU_FREQ_TABLE if CPU_FREQ |
| help |
| Support for NVIDIA Tegra T30 processor family, based on the |
| ARM CortexA9MP CPU and the ARM PL310 L2 cache controller |
| |
| config TEGRA_PCI |
| bool "PCI Express support" |
| depends on ARCH_TEGRA_2x_SOC |
| select PCI |
| |
| config TEGRA_AHB |
| bool "Enable AHB driver for NVIDIA Tegra SoCs" |
| default y |
| help |
| Adds AHB configuration functionality for NVIDIA Tegra SoCs, |
| which controls AHB bus master arbitration and some |
| perfomance parameters(priority, prefech size). |
| |
| comment "Tegra board type" |
| |
| choice |
| prompt "Default low-level debug console UART" |
| default TEGRA_DEBUG_UART_NONE |
| |
| config TEGRA_DEBUG_UART_NONE |
| bool "None" |
| |
| config TEGRA_DEBUG_UARTA |
| bool "UART-A" |
| |
| config TEGRA_DEBUG_UARTB |
| bool "UART-B" |
| |
| config TEGRA_DEBUG_UARTC |
| bool "UART-C" |
| |
| config TEGRA_DEBUG_UARTD |
| bool "UART-D" |
| |
| config TEGRA_DEBUG_UARTE |
| bool "UART-E" |
| |
| endchoice |
| |
| choice |
| prompt "Automatic low-level debug console UART" |
| default TEGRA_DEBUG_UART_AUTO_NONE |
| |
| config TEGRA_DEBUG_UART_AUTO_NONE |
| bool "None" |
| |
| config TEGRA_DEBUG_UART_AUTO_ODMDATA |
| bool "Via ODMDATA" |
| help |
| Automatically determines which UART to use for low-level debug based |
| on the ODMDATA value. This value is part of the BCT, and is written |
| to the boot memory device using nvflash, or other flashing tool. |
| When bits 19:18 are 3, then bits 17:15 indicate which UART to use; |
| 0/1/2/3/4 are UART A/B/C/D/E. |
| |
| config TEGRA_DEBUG_UART_AUTO_SCRATCH |
| bool "Via UART scratch register" |
| help |
| Automatically determines which UART to use for low-level debug based |
| on the UART scratch register value. Some bootloaders put ASCII 'D' |
| in this register when they initialize their own console UART output. |
| Using this option allows the kernel to automatically pick the same |
| UART. |
| |
| endchoice |
| |
| config TEGRA_SYSTEM_DMA |
| bool "Enable system DMA driver for NVIDIA Tegra SoCs" |
| default y |
| help |
| Adds system DMA functionality for NVIDIA Tegra SoCs, used by |
| several Tegra device drivers |
| |
| config TEGRA_EMC_SCALING_ENABLE |
| bool "Enable scaling the memory frequency" |
| |
| endif |