ath9k: merge noisefloor load implementations
AR5008+ and AR9003 currently use two separate implementations of the
ath9k_hw_loadnf function. There are three main differences:
- PHY registers for AR9003 are different
- AR9003 always uses 3 chains, earlier versions are more selective
- The AR9003 variant contains a fix for NF load timeouts
This patch merges the two implementations into one, storing the
register array in the ath_hw struct. The fix for NF load timeouts is
not just relevant for AR9003, but also important for earlier hardware,
so it's better to just keep one common implementation.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.c b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
index 868b24a..7c93338 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_phy.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
@@ -1050,106 +1050,6 @@
}
/*
- * Find out which of the RX chains are enabled
- */
-static u32 ar9003_hw_get_rx_chainmask(struct ath_hw *ah)
-{
- u32 chain = REG_READ(ah, AR_PHY_RX_CHAINMASK);
- /*
- * The bits [2:0] indicate the rx chain mask and are to be
- * interpreted as follows:
- * 00x => Only chain 0 is enabled
- * 01x => Chain 1 and 0 enabled
- * 1xx => Chain 2,1 and 0 enabled
- */
- return chain & 0x7;
-}
-
-static void ar9003_hw_loadnf(struct ath_hw *ah, struct ath9k_channel *chan)
-{
- struct ath9k_nfcal_hist *h;
- unsigned i, j;
- int32_t val;
- const u32 ar9300_cca_regs[6] = {
- AR_PHY_CCA_0,
- AR_PHY_CCA_1,
- AR_PHY_CCA_2,
- AR_PHY_EXT_CCA,
- AR_PHY_EXT_CCA_1,
- AR_PHY_EXT_CCA_2,
- };
- u8 chainmask, rx_chain_status;
- struct ath_common *common = ath9k_hw_common(ah);
-
- rx_chain_status = ar9003_hw_get_rx_chainmask(ah);
-
- chainmask = 0x3F;
- h = ah->nfCalHist;
-
- for (i = 0; i < NUM_NF_READINGS; i++) {
- if (chainmask & (1 << i)) {
- val = REG_READ(ah, ar9300_cca_regs[i]);
- val &= 0xFFFFFE00;
- val |= (((u32) (h[i].privNF) << 1) & 0x1ff);
- REG_WRITE(ah, ar9300_cca_regs[i], val);
- }
- }
-
- /*
- * Load software filtered NF value into baseband internal minCCApwr
- * variable.
- */
- REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL,
- AR_PHY_AGC_CONTROL_ENABLE_NF);
- REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL,
- AR_PHY_AGC_CONTROL_NO_UPDATE_NF);
- REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);
-
- /*
- * Wait for load to complete, should be fast, a few 10s of us.
- * The max delay was changed from an original 250us to 10000us
- * since 250us often results in NF load timeout and causes deaf
- * condition during stress testing 12/12/2009
- */
- for (j = 0; j < 1000; j++) {
- if ((REG_READ(ah, AR_PHY_AGC_CONTROL) &
- AR_PHY_AGC_CONTROL_NF) == 0)
- break;
- udelay(10);
- }
-
- /*
- * We timed out waiting for the noisefloor to load, probably due to an
- * in-progress rx. Simply return here and allow the load plenty of time
- * to complete before the next calibration interval. We need to avoid
- * trying to load -50 (which happens below) while the previous load is
- * still in progress as this can cause rx deafness. Instead by returning
- * here, the baseband nf cal will just be capped by our present
- * noisefloor until the next calibration timer.
- */
- if (j == 1000) {
- ath_print(common, ATH_DBG_ANY, "Timeout while waiting for nf "
- "to load: AR_PHY_AGC_CONTROL=0x%x\n",
- REG_READ(ah, AR_PHY_AGC_CONTROL));
- return;
- }
-
- /*
- * Restore maxCCAPower register parameter again so that we're not capped
- * by the median we just loaded. This will be initial (and max) value
- * of next noise floor calibration the baseband does.
- */
- for (i = 0; i < NUM_NF_READINGS; i++) {
- if (chainmask & (1 << i)) {
- val = REG_READ(ah, ar9300_cca_regs[i]);
- val &= 0xFFFFFE00;
- val |= (((u32) (-50) << 1) & 0x1ff);
- REG_WRITE(ah, ar9300_cca_regs[i], val);
- }
- }
-}
-
-/*
* Initialize the ANI register values with default (ini) values.
* This routine is called during a (full) hardware reset after
* all the registers are initialised from the INI.
@@ -1216,6 +1116,14 @@
void ar9003_hw_attach_phy_ops(struct ath_hw *ah)
{
struct ath_hw_private_ops *priv_ops = ath9k_hw_private_ops(ah);
+ const u32 ar9300_cca_regs[6] = {
+ AR_PHY_CCA_0,
+ AR_PHY_CCA_1,
+ AR_PHY_CCA_2,
+ AR_PHY_EXT_CCA,
+ AR_PHY_EXT_CCA_1,
+ AR_PHY_EXT_CCA_2,
+ };
priv_ops->rf_set_freq = ar9003_hw_set_channel;
priv_ops->spur_mitigate_freq = ar9003_hw_spur_mitigate;
@@ -1232,10 +1140,10 @@
priv_ops->set_diversity = ar9003_hw_set_diversity;
priv_ops->ani_control = ar9003_hw_ani_control;
priv_ops->do_getnf = ar9003_hw_do_getnf;
- priv_ops->loadnf = ar9003_hw_loadnf;
priv_ops->ani_cache_ini_regs = ar9003_hw_ani_cache_ini_regs;
ar9003_hw_set_nf_limits(ah);
+ memcpy(ah->nf_regs, ar9300_cca_regs, sizeof(ah->nf_regs));
}
void ar9003_hw_bb_watchdog_config(struct ath_hw *ah)