Thermal: exynos: Add sysfs node supporting exynos's emulation mode.
This patch supports exynos's emulation mode with newly created sysfs node.
Exynos 4x12 (4212, 4412) and 5 series provide emulation mode for thermal
management unit. Thermal emulation mode supports software debug for TMU's
operation. User can set temperature manually with software code and TMU
will read current temperature from user value not from sensor's value.
This patch includes also documentary placed under Documentation/thermal/.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
diff --git a/Documentation/thermal/exynos_thermal_emulation b/Documentation/thermal/exynos_thermal_emulation
new file mode 100644
index 0000000..b73bbfb
--- /dev/null
+++ b/Documentation/thermal/exynos_thermal_emulation
@@ -0,0 +1,53 @@
+EXYNOS EMULATION MODE
+========================
+
+Copyright (C) 2012 Samsung Electronics
+
+Written by Jonghwa Lee <jonghwa3.lee@samsung.com>
+
+Description
+-----------
+
+Exynos 4x12 (4212, 4412) and 5 series provide emulation mode for thermal management unit.
+Thermal emulation mode supports software debug for TMU's operation. User can set temperature
+manually with software code and TMU will read current temperature from user value not from
+sensor's value.
+
+Enabling CONFIG_EXYNOS_THERMAL_EMUL option will make this support in available.
+When it's enabled, sysfs node will be created under
+/sys/bus/platform/devices/'exynos device name'/ with name of 'emulation'.
+
+The sysfs node, 'emulation', will contain value 0 for the initial state. When you input any
+temperature you want to update to sysfs node, it automatically enable emulation mode and
+current temperature will be changed into it.
+(Exynos also supports user changable delay time which would be used to delay of
+ changing temperature. However, this node only uses same delay of real sensing time, 938us.)
+
+Exynos emulation mode requires synchronous of value changing and enabling. It means when you
+want to update the any value of delay or next temperature, then you have to enable emulation
+mode at the same time. (Or you have to keep the mode enabling.) If you don't, it fails to
+change the value to updated one and just use last succeessful value repeatedly. That's why
+this node gives users the right to change termerpature only. Just one interface makes it more
+simply to use.
+
+Disabling emulation mode only requires writing value 0 to sysfs node.
+
+
+TEMP 120 |
+ |
+ 100 |
+ |
+ 80 |
+ | +-----------
+ 60 | | |
+ | +-------------| |
+ 40 | | | |
+ | | | |
+ 20 | | | +----------
+ | | | | |
+ 0 |______________|_____________|__________|__________|_________
+ A A A A TIME
+ |<----->| |<----->| |<----->| |
+ | 938us | | | | | |
+emulation : 0 50 | 70 | 20 | 0
+current temp : sensor 50 70 20 sensor
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index c2c77d1..c31b9e4 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -101,6 +101,15 @@
If you say yes here you get support for TMU (Thermal Management
Unit) on SAMSUNG EXYNOS series of SoC.
+config EXYNOS_THERMAL_EMUL
+ bool "EXYNOS TMU emulation mode support"
+ depends on EXYNOS_THERMAL
+ help
+ Exynos 4412 and 4414 and 5 series has emulation mode on TMU.
+ Enable this option will be make sysfs node in exynos thermal platform
+ device directory to support emulation mode. With emulation mode sysfs
+ node, you can manually input temperature to TMU for simulation purpose.
+
config DB8500_THERMAL
bool "DB8500 thermal management"
depends on ARCH_U8500
diff --git a/drivers/thermal/exynos_thermal.c b/drivers/thermal/exynos_thermal.c
index 7772d16..e2ef8a3 100644
--- a/drivers/thermal/exynos_thermal.c
+++ b/drivers/thermal/exynos_thermal.c
@@ -99,6 +99,14 @@
#define IDLE_INTERVAL 10000
#define MCELSIUS 1000
+#ifdef CONFIG_EXYNOS_THERMAL_EMUL
+#define EXYNOS_EMUL_TIME 0x57F0
+#define EXYNOS_EMUL_TIME_SHIFT 16
+#define EXYNOS_EMUL_DATA_SHIFT 8
+#define EXYNOS_EMUL_DATA_MASK 0xFF
+#define EXYNOS_EMUL_ENABLE 0x1
+#endif /* CONFIG_EXYNOS_THERMAL_EMUL */
+
/* CPU Zone information */
#define PANIC_ZONE 4
#define WARN_ZONE 3
@@ -832,6 +840,94 @@
return (struct exynos_tmu_platform_data *)
platform_get_device_id(pdev)->driver_data;
}
+
+#ifdef CONFIG_EXYNOS_THERMAL_EMUL
+static ssize_t exynos_tmu_emulation_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct platform_device *pdev = container_of(dev,
+ struct platform_device, dev);
+ struct exynos_tmu_data *data = platform_get_drvdata(pdev);
+ unsigned int reg;
+ u8 temp_code;
+ int temp = 0;
+
+ if (data->soc == SOC_ARCH_EXYNOS4210)
+ goto out;
+
+ mutex_lock(&data->lock);
+ clk_enable(data->clk);
+ reg = readl(data->base + EXYNOS_EMUL_CON);
+ clk_disable(data->clk);
+ mutex_unlock(&data->lock);
+
+ if (reg & EXYNOS_EMUL_ENABLE) {
+ reg >>= EXYNOS_EMUL_DATA_SHIFT;
+ temp_code = reg & EXYNOS_EMUL_DATA_MASK;
+ temp = code_to_temp(data, temp_code);
+ }
+out:
+ return sprintf(buf, "%d\n", temp * MCELSIUS);
+}
+
+static ssize_t exynos_tmu_emulation_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct platform_device *pdev = container_of(dev,
+ struct platform_device, dev);
+ struct exynos_tmu_data *data = platform_get_drvdata(pdev);
+ unsigned int reg;
+ int temp;
+
+ if (data->soc == SOC_ARCH_EXYNOS4210)
+ goto out;
+
+ if (!sscanf(buf, "%d\n", &temp) || temp < 0)
+ return -EINVAL;
+
+ mutex_lock(&data->lock);
+ clk_enable(data->clk);
+
+ reg = readl(data->base + EXYNOS_EMUL_CON);
+
+ if (temp) {
+ /* Both CELSIUS and MCELSIUS type are available for input */
+ if (temp > MCELSIUS)
+ temp /= MCELSIUS;
+
+ reg = (EXYNOS_EMUL_TIME << EXYNOS_EMUL_TIME_SHIFT) |
+ (temp_to_code(data, (temp / MCELSIUS))
+ << EXYNOS_EMUL_DATA_SHIFT) | EXYNOS_EMUL_ENABLE;
+ } else {
+ reg &= ~EXYNOS_EMUL_ENABLE;
+ }
+
+ writel(reg, data->base + EXYNOS_EMUL_CON);
+
+ clk_disable(data->clk);
+ mutex_unlock(&data->lock);
+
+out:
+ return count;
+}
+
+static DEVICE_ATTR(emulation, 0644, exynos_tmu_emulation_show,
+ exynos_tmu_emulation_store);
+static int create_emulation_sysfs(struct device *dev)
+{
+ return device_create_file(dev, &dev_attr_emulation);
+}
+static void remove_emulation_sysfs(struct device *dev)
+{
+ device_remove_file(dev, &dev_attr_emulation);
+}
+#else
+static inline int create_emulation_sysfs(struct device *dev) { return 0; }
+static inline void remove_emulation_sysfs(struct device *dev) {}
+#endif
+
static int __devinit exynos_tmu_probe(struct platform_device *pdev)
{
struct exynos_tmu_data *data;
@@ -930,6 +1026,11 @@
dev_err(&pdev->dev, "Failed to register thermal interface\n");
goto err_clk;
}
+
+ ret = create_emulation_sysfs(&pdev->dev);
+ if (ret)
+ dev_err(&pdev->dev, "Failed to create emulation mode sysfs node\n");
+
return 0;
err_clk:
platform_set_drvdata(pdev, NULL);
@@ -941,6 +1042,8 @@
{
struct exynos_tmu_data *data = platform_get_drvdata(pdev);
+ remove_emulation_sysfs(&pdev->dev);
+
exynos_tmu_control(pdev, false);
exynos_unregister_thermal();