mfd: Janz CMOD-IO PCI MODULbus Carrier Board support
The Janz CMOD-IO PCI MODULbus carrier board is a PCI to MODULbus bridge,
which may host many different types of MODULbus daughterboards, including
CAN and GPIO controllers.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Reviewed-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 93d0e31..05c137d 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -418,6 +418,16 @@
southbridge which provides access to GPIOs and Watchdog using the
southbridge PCI device configuration space.
+config MFD_JANZ_CMODIO
+ tristate "Support for Janz CMOD-IO PCI MODULbus Carrier Board"
+ select MFD_CORE
+ depends on PCI
+ help
+ This is the core driver for the Janz CMOD-IO PCI MODULbus
+ carrier board. This device is a PCI to MODULbus bridge which may
+ host many different types of MODULbus daughterboards, including
+ CAN and GPIO controllers.
+
endmenu
menu "Multimedia Capabilities Port drivers"
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index f177e06..21eff85 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -65,3 +65,4 @@
obj-$(CONFIG_PMIC_ADP5520) += adp5520.o
obj-$(CONFIG_LPC_SCH) += lpc_sch.o
obj-$(CONFIG_MFD_RDC321X) += rdc321x-southbridge.o
+obj-$(CONFIG_MFD_JANZ_CMODIO) += janz-cmodio.o
diff --git a/drivers/mfd/janz-cmodio.c b/drivers/mfd/janz-cmodio.c
new file mode 100644
index 0000000..9ed6307
--- /dev/null
+++ b/drivers/mfd/janz-cmodio.c
@@ -0,0 +1,304 @@
+/*
+ * Janz CMOD-IO MODULbus Carrier Board PCI Driver
+ *
+ * Copyright (c) 2010 Ira W. Snyder <iws@ovro.caltech.edu>
+ *
+ * Lots of inspiration and code was copied from drivers/mfd/sm501.c
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/core.h>
+
+#include <linux/mfd/janz.h>
+
+#define DRV_NAME "janz-cmodio"
+
+/* Size of each MODULbus module in PCI BAR4 */
+#define CMODIO_MODULBUS_SIZE 0x200
+
+/* Maximum number of MODULbus modules on a CMOD-IO carrier board */
+#define CMODIO_MAX_MODULES 4
+
+/* Module Parameters */
+static unsigned int num_modules = CMODIO_MAX_MODULES;
+static unsigned char *modules[CMODIO_MAX_MODULES] = {
+ "empty", "empty", "empty", "empty",
+};
+
+module_param_array(modules, charp, &num_modules, S_IRUGO);
+MODULE_PARM_DESC(modules, "MODULbus modules attached to the carrier board");
+
+/* Unique Device Id */
+static unsigned int cmodio_id;
+
+struct cmodio_device {
+ /* Parent PCI device */
+ struct pci_dev *pdev;
+
+ /* PLX control registers */
+ struct janz_cmodio_onboard_regs __iomem *ctrl;
+
+ /* hex switch position */
+ u8 hex;
+
+ /* mfd-core API */
+ struct mfd_cell cells[CMODIO_MAX_MODULES];
+ struct resource resources[3 * CMODIO_MAX_MODULES];
+ struct janz_platform_data pdata[CMODIO_MAX_MODULES];
+};
+
+/*
+ * Subdevices using the mfd-core API
+ */
+
+static int __devinit cmodio_setup_subdevice(struct cmodio_device *priv,
+ char *name, unsigned int devno,
+ unsigned int modno)
+{
+ struct janz_platform_data *pdata;
+ struct mfd_cell *cell;
+ struct resource *res;
+ struct pci_dev *pci;
+
+ pci = priv->pdev;
+ cell = &priv->cells[devno];
+ res = &priv->resources[devno * 3];
+ pdata = &priv->pdata[devno];
+
+ cell->name = name;
+ cell->resources = res;
+ cell->num_resources = 3;
+
+ /* Setup the subdevice ID -- must be unique */
+ cell->id = cmodio_id++;
+
+ /* Add platform data */
+ pdata->modno = modno;
+ cell->platform_data = pdata;
+ cell->data_size = sizeof(*pdata);
+
+ /* MODULbus registers -- PCI BAR3 is big-endian MODULbus access */
+ res->flags = IORESOURCE_MEM;
+ res->parent = &pci->resource[3];
+ res->start = pci->resource[3].start + (CMODIO_MODULBUS_SIZE * modno);
+ res->end = res->start + CMODIO_MODULBUS_SIZE - 1;
+ res++;
+
+ /* PLX Control Registers -- PCI BAR4 is interrupt and other registers */
+ res->flags = IORESOURCE_MEM;
+ res->parent = &pci->resource[4];
+ res->start = pci->resource[4].start;
+ res->end = pci->resource[4].end;
+ res++;
+
+ /*
+ * IRQ
+ *
+ * The start and end fields are used as an offset to the irq_base
+ * parameter passed into the mfd_add_devices() function call. All
+ * devices share the same IRQ.
+ */
+ res->flags = IORESOURCE_IRQ;
+ res->parent = NULL;
+ res->start = 0;
+ res->end = 0;
+ res++;
+
+ return 0;
+}
+
+/* Probe each submodule using kernel parameters */
+static int __devinit cmodio_probe_submodules(struct cmodio_device *priv)
+{
+ struct pci_dev *pdev = priv->pdev;
+ unsigned int num_probed = 0;
+ char *name;
+ int i;
+
+ for (i = 0; i < num_modules; i++) {
+ name = modules[i];
+ if (!strcmp(name, "") || !strcmp(name, "empty"))
+ continue;
+
+ dev_dbg(&priv->pdev->dev, "MODULbus %d: name %s\n", i, name);
+ cmodio_setup_subdevice(priv, name, num_probed, i);
+ num_probed++;
+ }
+
+ /* print an error message if no modules were probed */
+ if (num_probed == 0) {
+ dev_err(&priv->pdev->dev, "no MODULbus modules specified, "
+ "please set the ``modules'' kernel "
+ "parameter according to your "
+ "hardware configuration\n");
+ return -ENODEV;
+ }
+
+ return mfd_add_devices(&pdev->dev, 0, priv->cells,
+ num_probed, NULL, pdev->irq);
+}
+
+/*
+ * SYSFS Attributes
+ */
+
+static ssize_t mbus_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct cmodio_device *priv = dev_get_drvdata(dev);
+
+ return snprintf(buf, PAGE_SIZE, "%x\n", priv->hex);
+}
+
+static DEVICE_ATTR(modulbus_number, S_IRUGO, mbus_show, NULL);
+
+static struct attribute *cmodio_sysfs_attrs[] = {
+ &dev_attr_modulbus_number.attr,
+ NULL,
+};
+
+static const struct attribute_group cmodio_sysfs_attr_group = {
+ .attrs = cmodio_sysfs_attrs,
+};
+
+/*
+ * PCI Driver
+ */
+
+static int __devinit cmodio_pci_probe(struct pci_dev *dev,
+ const struct pci_device_id *id)
+{
+ struct cmodio_device *priv;
+ int ret;
+
+ priv = kzalloc(sizeof(*priv), GFP_KERNEL);
+ if (!priv) {
+ dev_err(&dev->dev, "unable to allocate private data\n");
+ ret = -ENOMEM;
+ goto out_return;
+ }
+
+ pci_set_drvdata(dev, priv);
+ priv->pdev = dev;
+
+ /* Hardware Initialization */
+ ret = pci_enable_device(dev);
+ if (ret) {
+ dev_err(&dev->dev, "unable to enable device\n");
+ goto out_free_priv;
+ }
+
+ pci_set_master(dev);
+ ret = pci_request_regions(dev, DRV_NAME);
+ if (ret) {
+ dev_err(&dev->dev, "unable to request regions\n");
+ goto out_pci_disable_device;
+ }
+
+ /* Onboard configuration registers */
+ priv->ctrl = pci_ioremap_bar(dev, 4);
+ if (!priv->ctrl) {
+ dev_err(&dev->dev, "unable to remap onboard regs\n");
+ ret = -ENOMEM;
+ goto out_pci_release_regions;
+ }
+
+ /* Read the hex switch on the carrier board */
+ priv->hex = ioread8(&priv->ctrl->int_enable);
+
+ /* Add the MODULbus number (hex switch value) to the device's sysfs */
+ ret = sysfs_create_group(&dev->dev.kobj, &cmodio_sysfs_attr_group);
+ if (ret) {
+ dev_err(&dev->dev, "unable to create sysfs attributes\n");
+ goto out_unmap_ctrl;
+ }
+
+ /*
+ * Disable all interrupt lines, each submodule will enable its
+ * own interrupt line if needed
+ */
+ iowrite8(0xf, &priv->ctrl->int_disable);
+
+ /* Register drivers for all submodules */
+ ret = cmodio_probe_submodules(priv);
+ if (ret) {
+ dev_err(&dev->dev, "unable to probe submodules\n");
+ goto out_sysfs_remove_group;
+ }
+
+ return 0;
+
+out_sysfs_remove_group:
+ sysfs_remove_group(&dev->dev.kobj, &cmodio_sysfs_attr_group);
+out_unmap_ctrl:
+ iounmap(priv->ctrl);
+out_pci_release_regions:
+ pci_release_regions(dev);
+out_pci_disable_device:
+ pci_disable_device(dev);
+out_free_priv:
+ kfree(priv);
+out_return:
+ return ret;
+}
+
+static void __devexit cmodio_pci_remove(struct pci_dev *dev)
+{
+ struct cmodio_device *priv = pci_get_drvdata(dev);
+
+ mfd_remove_devices(&dev->dev);
+ sysfs_remove_group(&dev->dev.kobj, &cmodio_sysfs_attr_group);
+ iounmap(priv->ctrl);
+ pci_release_regions(dev);
+ pci_disable_device(dev);
+ kfree(priv);
+}
+
+#define PCI_VENDOR_ID_JANZ 0x13c3
+
+/* The list of devices that this module will support */
+static DEFINE_PCI_DEVICE_TABLE(cmodio_pci_ids) = {
+ { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030, PCI_VENDOR_ID_JANZ, 0x0101 },
+ { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050, PCI_VENDOR_ID_JANZ, 0x0100 },
+ { 0, }
+};
+MODULE_DEVICE_TABLE(pci, cmodio_pci_ids);
+
+static struct pci_driver cmodio_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = cmodio_pci_ids,
+ .probe = cmodio_pci_probe,
+ .remove = __devexit_p(cmodio_pci_remove),
+};
+
+/*
+ * Module Init / Exit
+ */
+
+static int __init cmodio_init(void)
+{
+ return pci_register_driver(&cmodio_pci_driver);
+}
+
+static void __exit cmodio_exit(void)
+{
+ pci_unregister_driver(&cmodio_pci_driver);
+}
+
+MODULE_AUTHOR("Ira W. Snyder <iws@ovro.caltech.edu>");
+MODULE_DESCRIPTION("Janz CMOD-IO PCI MODULbus Carrier Board Driver");
+MODULE_LICENSE("GPL");
+
+module_init(cmodio_init);
+module_exit(cmodio_exit);
diff --git a/include/linux/mfd/janz.h b/include/linux/mfd/janz.h
new file mode 100644
index 0000000..e9994c4
--- /dev/null
+++ b/include/linux/mfd/janz.h
@@ -0,0 +1,54 @@
+/*
+ * Common Definitions for Janz MODULbus devices
+ *
+ * Copyright (c) 2010 Ira W. Snyder <iws@ovro.caltech.edu>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#ifndef JANZ_H
+#define JANZ_H
+
+struct janz_platform_data {
+ /* MODULbus Module Number */
+ unsigned int modno;
+};
+
+/* PLX bridge chip onboard registers */
+struct janz_cmodio_onboard_regs {
+ u8 unused1;
+
+ /*
+ * Read access: interrupt status
+ * Write access: interrupt disable
+ */
+ u8 int_disable;
+ u8 unused2;
+
+ /*
+ * Read access: MODULbus number (hex switch)
+ * Write access: interrupt enable
+ */
+ u8 int_enable;
+ u8 unused3;
+
+ /* write-only */
+ u8 reset_assert;
+ u8 unused4;
+
+ /* write-only */
+ u8 reset_deassert;
+ u8 unused5;
+
+ /* read-write access to serial EEPROM */
+ u8 eep;
+ u8 unused6;
+
+ /* write-only access to EEPROM chip select */
+ u8 enid;
+};
+
+#endif /* JANZ_H */