b43: adjust code to compile without SSB
Users of new (BCMA based) wireless chipsets may not want to enable SSB.
This is hopefully the last code patch for dropping SSB dependency.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/b43/main.c b/drivers/net/wireless/b43/main.c
index 32e08d3..558abe7 100644
--- a/drivers/net/wireless/b43/main.c
+++ b/drivers/net/wireless/b43/main.c
@@ -1208,6 +1208,7 @@
}
#endif
+#ifdef CONFIG_B43_SSB
static void b43_ssb_wireless_core_reset(struct b43_wldev *dev, bool gmode)
{
struct ssb_device *sdev = dev->dev->sdev;
@@ -1235,6 +1236,7 @@
ssb_read32(sdev, SSB_TMSLOW); /* flush */
msleep(1);
}
+#endif
void b43_wireless_core_reset(struct b43_wldev *dev, bool gmode)
{
@@ -2735,6 +2737,8 @@
/* Initialize the GPIOs
* http://bcm-specs.sipsolutions.net/GPIO
*/
+
+#ifdef CONFIG_B43_SSB
static struct ssb_device *b43_ssb_gpio_dev(struct b43_wldev *dev)
{
struct ssb_bus *bus = dev->dev->sdev->bus;
@@ -2745,10 +2749,13 @@
return bus->chipco.dev;
#endif
}
+#endif
static int b43_gpio_init(struct b43_wldev *dev)
{
+#ifdef CONFIG_B43_SSB
struct ssb_device *gpiodev;
+#endif
u32 mask, set;
b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_GPOUTSMSK, 0);
@@ -2807,7 +2814,9 @@
/* Turn off all GPIO stuff. Call this on module unload, for example. */
static void b43_gpio_cleanup(struct b43_wldev *dev)
{
+#ifdef CONFIG_B43_SSB
struct ssb_device *gpiodev;
+#endif
switch (dev->dev->bus_type) {
#ifdef CONFIG_B43_BCMA
@@ -3692,7 +3701,9 @@
static void b43_put_phy_into_reset(struct b43_wldev *dev)
{
+#ifdef CONFIG_B43_SSB
u32 tmp;
+#endif
switch (dev->dev->bus_type) {
#ifdef CONFIG_B43_BCMA
@@ -4582,8 +4593,12 @@
struct ssb_bus *bus;
u32 tmp;
+#ifdef CONFIG_B43_SSB
if (dev->dev->bus_type != B43_BUS_SSB)
return;
+#else
+ return;
+#endif
bus = dev->dev->sdev->bus;
@@ -4738,7 +4753,7 @@
}
if (sprom->boardflags_lo & B43_BFL_XTAL_NOSLOW)
hf |= B43_HF_DSCRQ; /* Disable slowclock requests from ucode. */
-#ifdef CONFIG_SSB_DRIVER_PCICORE
+#if defined(CONFIG_B43_SSB) && defined(CONFIG_SSB_DRIVER_PCICORE)
if (dev->dev->bus_type == B43_BUS_SSB &&
dev->dev->sdev->bus->bustype == SSB_BUSTYPE_PCI &&
dev->dev->sdev->bus->pcicore.dev->id.revision <= 10)
@@ -5310,6 +5325,7 @@
(pdev->subsystem_vendor == PCI_VENDOR_ID_##_subvendor) && \
(pdev->subsystem_device == _subdevice) )
+#ifdef CONFIG_B43_SSB
static void b43_sprom_fixup(struct ssb_bus *bus)
{
struct pci_dev *pdev;
@@ -5341,6 +5357,7 @@
ssb_set_devtypedata(dev->sdev, NULL);
ieee80211_free_hw(hw);
}
+#endif
static struct b43_wl *b43_wireless_init(struct b43_bus_dev *dev)
{