diff --git a/drivers/tty/Kconfig b/drivers/tty/Kconfig
new file mode 100644
index 0000000..9cfbdb3
--- /dev/null
+++ b/drivers/tty/Kconfig
@@ -0,0 +1,150 @@
+config VT
+	bool "Virtual terminal" if EXPERT
+	depends on !S390
+	select INPUT
+	default y
+	---help---
+	  If you say Y here, you will get support for terminal devices with
+	  display and keyboard devices. These are called "virtual" because you
+	  can run several virtual terminals (also called virtual consoles) on
+	  one physical terminal. This is rather useful, for example one
+	  virtual terminal can collect system messages and warnings, another
+	  one can be used for a text-mode user session, and a third could run
+	  an X session, all in parallel. Switching between virtual terminals
+	  is done with certain key combinations, usually Alt-<function key>.
+
+	  The setterm command ("man setterm") can be used to change the
+	  properties (such as colors or beeping) of a virtual terminal. The
+	  man page console_codes(4) ("man console_codes") contains the special
+	  character sequences that can be used to change those properties
+	  directly. The fonts used on virtual terminals can be changed with
+	  the setfont ("man setfont") command and the key bindings are defined
+	  with the loadkeys ("man loadkeys") command.
+
+	  You need at least one virtual terminal device in order to make use
+	  of your keyboard and monitor. Therefore, only people configuring an
+	  embedded system would want to say N here in order to save some
+	  memory; the only way to log into such a system is then via a serial
+	  or network connection.
+
+	  If unsure, say Y, or else you won't be able to do much with your new
+	  shiny Linux system :-)
+
+config CONSOLE_TRANSLATIONS
+	depends on VT
+	default y
+	bool "Enable character translations in console" if EXPERT
+	---help---
+	  This enables support for font mapping and Unicode translation
+	  on virtual consoles.
+
+config VT_CONSOLE
+	bool "Support for console on virtual terminal" if EXPERT
+	depends on VT
+	default y
+	---help---
+	  The system console is the device which receives all kernel messages
+	  and warnings and which allows logins in single user mode. If you
+	  answer Y here, a virtual terminal (the device used to interact with
+	  a physical terminal) can be used as system console. This is the most
+	  common mode of operations, so you should say Y here unless you want
+	  the kernel messages be output only to a serial port (in which case
+	  you should say Y to "Console on serial port", below).
+
+	  If you do say Y here, by default the currently visible virtual
+	  terminal (/dev/tty0) will be used as system console. You can change
+	  that with a kernel command line option such as "console=tty3" which
+	  would use the third virtual terminal as system console. (Try "man
+	  bootparam" or see the documentation of your boot loader (lilo or
+	  loadlin) about how to pass options to the kernel at boot time.)
+
+	  If unsure, say Y.
+
+config HW_CONSOLE
+	bool
+	depends on VT && !S390 && !UML
+	default y
+
+config VT_HW_CONSOLE_BINDING
+       bool "Support for binding and unbinding console drivers"
+       depends on HW_CONSOLE
+       default n
+       ---help---
+         The virtual terminal is the device that interacts with the physical
+         terminal through console drivers. On these systems, at least one
+         console driver is loaded. In other configurations, additional console
+         drivers may be enabled, such as the framebuffer console. If more than
+         1 console driver is enabled, setting this to 'y' will allow you to
+         select the console driver that will serve as the backend for the
+         virtual terminals.
+
+	 See <file:Documentation/console/console.txt> for more
+	 information. For framebuffer console users, please refer to
+	 <file:Documentation/fb/fbcon.txt>.
+
+config UNIX98_PTYS
+	bool "Unix98 PTY support" if EXPERT
+	default y
+	---help---
+	  A pseudo terminal (PTY) is a software device consisting of two
+	  halves: a master and a slave. The slave device behaves identical to
+	  a physical terminal; the master device is used by a process to
+	  read data from and write data to the slave, thereby emulating a
+	  terminal. Typical programs for the master side are telnet servers
+	  and xterms.
+
+	  Linux has traditionally used the BSD-like names /dev/ptyxx for
+	  masters and /dev/ttyxx for slaves of pseudo terminals. This scheme
+	  has a number of problems. The GNU C library glibc 2.1 and later,
+	  however, supports the Unix98 naming standard: in order to acquire a
+	  pseudo terminal, a process opens /dev/ptmx; the number of the pseudo
+	  terminal is then made available to the process and the pseudo
+	  terminal slave can be accessed as /dev/pts/<number>. What was
+	  traditionally /dev/ttyp2 will then be /dev/pts/2, for example.
+
+	  All modern Linux systems use the Unix98 ptys.  Say Y unless
+	  you're on an embedded system and want to conserve memory.
+
+config DEVPTS_MULTIPLE_INSTANCES
+	bool "Support multiple instances of devpts"
+	depends on UNIX98_PTYS
+	default n
+	---help---
+	  Enable support for multiple instances of devpts filesystem.
+	  If you want to have isolated PTY namespaces (eg: in containers),
+	  say Y here.  Otherwise, say N. If enabled, each mount of devpts
+	  filesystem with the '-o newinstance' option will create an
+	  independent PTY namespace.
+
+config LEGACY_PTYS
+	bool "Legacy (BSD) PTY support"
+	default y
+	---help---
+	  A pseudo terminal (PTY) is a software device consisting of two
+	  halves: a master and a slave. The slave device behaves identical to
+	  a physical terminal; the master device is used by a process to
+	  read data from and write data to the slave, thereby emulating a
+	  terminal. Typical programs for the master side are telnet servers
+	  and xterms.
+
+	  Linux has traditionally used the BSD-like names /dev/ptyxx
+	  for masters and /dev/ttyxx for slaves of pseudo
+	  terminals. This scheme has a number of problems, including
+	  security.  This option enables these legacy devices; on most
+	  systems, it is safe to say N.
+
+
+config LEGACY_PTY_COUNT
+	int "Maximum number of legacy PTY in use"
+	depends on LEGACY_PTYS
+	range 0 256
+	default "256"
+	---help---
+	  The maximum number of legacy PTYs that can be used at any one time.
+	  The default is 256, and should be more than enough.  Embedded
+	  systems may want to reduce this to save memory.
+
+	  When not in use, each legacy PTY occupies 12 bytes on 32-bit
+	  architectures and 24 bytes on 64-bit architectures.
+
+