ALSA: asoc: restrict sample rate and size in Freescale MPC8610 sound drivers
The Freescale MPC8610 SSI device has the option of using one clock for both
transmit and receive (synchronous mode), or independent clocks (asynchronous).
The SSI driver, however, programs the SSI into synchronous mode and then
tries to program the clock registers independently. The result is that the wrong
sample size is usually generated during recording.
This patch fixes the discrepancy by restricting the sample rate and sample size
of the playback and capture streams. The SSI driver remembers which stream
is opened first. When a second stream is opened, that stream is constrained
to the same sample rate and size as the first stream.
A future version of this driver will lift the sample size restriction.
Supporting independent sample rates is more difficult, because only certain
codecs provide dual independent clocks.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
diff --git a/sound/soc/fsl/fsl_dma.c b/sound/soc/fsl/fsl_dma.c
index da2bc59..7ceea2b 100644
--- a/sound/soc/fsl/fsl_dma.c
+++ b/sound/soc/fsl/fsl_dma.c
@@ -132,12 +132,17 @@
* Since each link descriptor has a 32-bit byte count field, we set
* period_bytes_max to the largest 32-bit number. We also have no maximum
* number of periods.
+ *
+ * Note that we specify SNDRV_PCM_INFO_JOINT_DUPLEX here, but only because a
+ * limitation in the SSI driver requires the sample rates for playback and
+ * capture to be the same.
*/
static const struct snd_pcm_hardware fsl_dma_hardware = {
.info = SNDRV_PCM_INFO_INTERLEAVED |
SNDRV_PCM_INFO_MMAP |
- SNDRV_PCM_INFO_MMAP_VALID,
+ SNDRV_PCM_INFO_MMAP_VALID |
+ SNDRV_PCM_INFO_JOINT_DUPLEX,
.formats = FSLDMA_PCM_FORMATS,
.rates = FSLDMA_PCM_RATES,
.rate_min = 5512,
diff --git a/sound/soc/fsl/fsl_ssi.c b/sound/soc/fsl/fsl_ssi.c
index 71bff33..157a789 100644
--- a/sound/soc/fsl/fsl_ssi.c
+++ b/sound/soc/fsl/fsl_ssi.c
@@ -67,6 +67,8 @@
* @ssi: pointer to the SSI's registers
* @ssi_phys: physical address of the SSI registers
* @irq: IRQ of this SSI
+ * @first_stream: pointer to the stream that was opened first
+ * @second_stream: pointer to second stream
* @dev: struct device pointer
* @playback: the number of playback streams opened
* @capture: the number of capture streams opened
@@ -79,6 +81,8 @@
struct ccsr_ssi __iomem *ssi;
dma_addr_t ssi_phys;
unsigned int irq;
+ struct snd_pcm_substream *first_stream;
+ struct snd_pcm_substream *second_stream;
struct device *dev;
unsigned int playback;
unsigned int capture;
@@ -342,6 +346,49 @@
*/
}
+ if (!ssi_private->first_stream)
+ ssi_private->first_stream = substream;
+ else {
+ /* This is the second stream open, so we need to impose sample
+ * rate and maybe sample size constraints. Note that this can
+ * cause a race condition if the second stream is opened before
+ * the first stream is fully initialized.
+ *
+ * We provide some protection by checking to make sure the first
+ * stream is initialized, but it's not perfect. ALSA sometimes
+ * re-initializes the driver with a different sample rate or
+ * size. If the second stream is opened before the first stream
+ * has received its final parameters, then the second stream may
+ * be constrained to the wrong sample rate or size.
+ *
+ * FIXME: This code does not handle opening and closing streams
+ * repeatedly. If you open two streams and then close the first
+ * one, you may not be able to open another stream until you
+ * close the second one as well.
+ */
+ struct snd_pcm_runtime *first_runtime =
+ ssi_private->first_stream->runtime;
+
+ if (!first_runtime->rate || !first_runtime->sample_bits) {
+ dev_err(substream->pcm->card->dev,
+ "set sample rate and size in %s stream first\n",
+ substream->stream == SNDRV_PCM_STREAM_PLAYBACK
+ ? "capture" : "playback");
+ return -EAGAIN;
+ }
+
+ snd_pcm_hw_constraint_minmax(substream->runtime,
+ SNDRV_PCM_HW_PARAM_RATE,
+ first_runtime->rate, first_runtime->rate);
+
+ snd_pcm_hw_constraint_minmax(substream->runtime,
+ SNDRV_PCM_HW_PARAM_SAMPLE_BITS,
+ first_runtime->sample_bits,
+ first_runtime->sample_bits);
+
+ ssi_private->second_stream = substream;
+ }
+
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
ssi_private->playback++;
@@ -371,18 +418,16 @@
struct fsl_ssi_private *ssi_private = rtd->dai->cpu_dai->private_data;
struct ccsr_ssi __iomem *ssi = ssi_private->ssi;
- u32 wl;
- wl = CCSR_SSI_SxCCR_WL(snd_pcm_format_width(runtime->format));
+ if (substream == ssi_private->first_stream) {
+ u32 wl;
- clrbits32(&ssi->scr, CCSR_SSI_SCR_SSIEN);
+ /* The SSI should always be disabled at this points (SSIEN=0) */
+ wl = CCSR_SSI_SxCCR_WL(snd_pcm_format_width(runtime->format));
- if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
+ /* In synchronous mode, the SSI uses STCCR for capture */
clrsetbits_be32(&ssi->stccr, CCSR_SSI_SxCCR_WL_MASK, wl);
- else
- clrsetbits_be32(&ssi->srccr, CCSR_SSI_SxCCR_WL_MASK, wl);
-
- setbits32(&ssi->scr, CCSR_SSI_SCR_SSIEN);
+ }
return 0;
}
@@ -407,9 +452,13 @@
case SNDRV_PCM_TRIGGER_RESUME:
case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
- setbits32(&ssi->scr, CCSR_SSI_SCR_TE);
+ clrbits32(&ssi->scr, CCSR_SSI_SCR_SSIEN);
+ setbits32(&ssi->scr,
+ CCSR_SSI_SCR_SSIEN | CCSR_SSI_SCR_TE);
} else {
- setbits32(&ssi->scr, CCSR_SSI_SCR_RE);
+ clrbits32(&ssi->scr, CCSR_SSI_SCR_SSIEN);
+ setbits32(&ssi->scr,
+ CCSR_SSI_SCR_SSIEN | CCSR_SSI_SCR_RE);
/*
* I think we need this delay to allow time for the SSI
@@ -452,6 +501,11 @@
if (substream->stream == SNDRV_PCM_STREAM_CAPTURE)
ssi_private->capture--;
+ if (ssi_private->first_stream == substream)
+ ssi_private->first_stream = ssi_private->second_stream;
+
+ ssi_private->second_stream = NULL;
+
/*
* If this is the last active substream, disable the SSI and release
* the IRQ.