ARM: Remove mach-msm and associated ARM architecture code
The maintainers for mach-msm no longer have any plans to support
or test the platforms supported by this architecture[1]. Most likely
there aren't any active users of this code anyway, so let's
delete it.
[1] http://lkml.kernel.org/r/20150307031212.GA8434@fifo99.com
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 970de75..b010202 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -448,25 +448,6 @@
Say Y here if you want kernel low-level debugging support
on MMP UART3.
- config DEBUG_MSM_UART
- bool "Kernel low-level debugging messages via MSM UART"
- depends on ARCH_MSM
- help
- Say Y here if you want the debug print routines to direct
- their output to the serial port on MSM devices.
-
- ARCH DEBUG_UART_PHYS DEBUG_UART_VIRT #
- MSM7X00A, QSD8X50 0xa9a00000 0xe1000000 UART1
- MSM7X00A, QSD8X50 0xa9b00000 0xe1000000 UART2
- MSM7X00A, QSD8X50 0xa9c00000 0xe1000000 UART3
-
- MSM7X30 0xaca00000 0xe1000000 UART1
- MSM7X30 0xacb00000 0xe1000000 UART2
- MSM7X30 0xacc00000 0xe1000000 UART3
-
- Please adjust DEBUG_UART_PHYS and DEBUG_UART_BASE configuration
- options based on your needs.
-
config DEBUG_QCOM_UARTDM
bool "Kernel low-level debugging messages via QCOM UARTDM"
depends on ARCH_QCOM
@@ -1295,7 +1276,7 @@
DEBUG_IMX6SL_UART || \
DEBUG_IMX6SX_UART
default "debug/ks8695.S" if DEBUG_KS8695_UART
- default "debug/msm.S" if DEBUG_MSM_UART || DEBUG_QCOM_UARTDM
+ default "debug/msm.S" if DEBUG_QCOM_UARTDM
default "debug/netx.S" if DEBUG_NETX_UART
default "debug/omap2plus.S" if DEBUG_OMAP2PLUS_UART
default "debug/renesas-scif.S" if DEBUG_R7S72100_SCIF2
@@ -1388,7 +1369,6 @@
default 0x80230000 if DEBUG_PICOXCELL_UART
default 0x808c0000 if ARCH_EP93XX
default 0x90020000 if DEBUG_NSPIRE_CLASSIC_UART || DEBUG_NSPIRE_CX_UART
- default 0xa9a00000 if DEBUG_MSM_UART
default 0xb0060000 if DEBUG_SIRFPRIMA2_UART1
default 0xb0090000 if DEBUG_VEXPRESS_UART0_CRX
default 0xc0013000 if DEBUG_U300_UART
@@ -1433,7 +1413,7 @@
DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \
DEBUG_LL_UART_EFM32 || \
DEBUG_UART_8250 || DEBUG_UART_PL01X || DEBUG_MESON_UARTAO || \
- DEBUG_MSM_UART || DEBUG_NETX_UART || \
+ DEBUG_NETX_UART || \
DEBUG_QCOM_UARTDM || DEBUG_R7S72100_SCIF2 || \
DEBUG_RCAR_GEN1_SCIF0 || DEBUG_RCAR_GEN1_SCIF2 || \
DEBUG_RCAR_GEN2_SCIF0 || DEBUG_RCAR_GEN2_SCIF2 || \
@@ -1446,7 +1426,6 @@
hex "Virtual base address of debug UART"
default 0xe0000a00 if DEBUG_NETX_UART
default 0xe0010fe0 if ARCH_RPC
- default 0xe1000000 if DEBUG_MSM_UART
default 0xf0000be0 if ARCH_EBSA110
default 0xf0010000 if DEBUG_ASM9260_UART
default 0xf01fb000 if DEBUG_NOMADIK_UART
@@ -1526,7 +1505,7 @@
default DEBUG_UART_PHYS if !MMU
depends on DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \
DEBUG_UART_8250 || DEBUG_UART_PL01X || DEBUG_MESON_UARTAO || \
- DEBUG_MSM_UART || DEBUG_NETX_UART || \
+ DEBUG_NETX_UART || \
DEBUG_QCOM_UARTDM || DEBUG_S3C24XX_UART || \
DEBUG_UART_BCM63XX || DEBUG_ASM9260_UART || \
DEBUG_SIRFSOC_UART || DEBUG_DIGICOLOR_UA0
@@ -1556,7 +1535,7 @@
config DEBUG_UNCOMPRESS
bool
- depends on ARCH_MULTIPLATFORM || ARCH_MSM || PLAT_SAMSUNG
+ depends on ARCH_MULTIPLATFORM || PLAT_SAMSUNG
default y if DEBUG_LL && !DEBUG_OMAP2PLUS_UART && \
(!DEBUG_TEGRA_UART || !ZBOOT_ROM)
help