rtl8xxxu: Reorder parts of init code to match the 8192eu vendor code flow
In order to debug 8192eu support, reorder some init code to match the
flow of the vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index e36fda8..d67b886 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -7592,6 +7592,26 @@
if (ret)
goto exit;
+ /* RFSW Control - clear bit 14 ?? */
+ if (priv->rtl_chip != RTL8723B)
+ rtl8xxxu_write32(priv, REG_FPGA0_TX_INFO, 0x00000003);
+ /* 0x07000760 */
+ if (priv->rtl_chip == RTL8192E) {
+ val32 = 0;
+ } else {
+ val32 = FPGA0_RF_TRSW | FPGA0_RF_TRSWB | FPGA0_RF_ANTSW |
+ FPGA0_RF_ANTSWB | FPGA0_RF_PAPE |
+ ((FPGA0_RF_ANTSW | FPGA0_RF_ANTSWB | FPGA0_RF_PAPE) <<
+ FPGA0_RF_BD_CTRL_SHIFT);
+ }
+ rtl8xxxu_write32(priv, REG_FPGA0_XAB_RF_SW_CTRL, val32);
+ /* 0x860[6:5]= 00 - why? - this sets antenna B */
+ if (priv->rtl_chip != RTL8192E)
+ rtl8xxxu_write32(priv, REG_FPGA0_XA_RF_INT_OE, 0x66f60210);
+
+ priv->rf_mode_ag[0] = rtl8xxxu_read_rfreg(priv, RF_A,
+ RF6052_REG_MODE_AG);
+
/*
* Chip specific quirks
*/
@@ -7653,21 +7673,6 @@
if (ret)
goto exit;
- /* RFSW Control - clear bit 14 ?? */
- if (priv->rtl_chip != RTL8723B)
- rtl8xxxu_write32(priv, REG_FPGA0_TX_INFO, 0x00000003);
- /* 0x07000760 */
- val32 = FPGA0_RF_TRSW | FPGA0_RF_TRSWB | FPGA0_RF_ANTSW |
- FPGA0_RF_ANTSWB | FPGA0_RF_PAPE |
- ((FPGA0_RF_ANTSW | FPGA0_RF_ANTSWB | FPGA0_RF_PAPE) <<
- FPGA0_RF_BD_CTRL_SHIFT);
- rtl8xxxu_write32(priv, REG_FPGA0_XAB_RF_SW_CTRL, val32);
- /* 0x860[6:5]= 00 - why? - this sets antenna B */
- rtl8xxxu_write32(priv, REG_FPGA0_XA_RF_INT_OE, 0x66F60210);
-
- priv->rf_mode_ag[0] = rtl8xxxu_read_rfreg(priv, RF_A,
- RF6052_REG_MODE_AG);
-
/*
* Set RX page boundary
*/