at91: Refactor Stamp9G20 and PControl G20 board file
As PControl G20 is a carrier board for the Stamp9G20 SoM, some code can
be shared. Therefore board-stamp9g20.c is refactored to allow reusing the
SoM initialization and board-pcontrol-g20.c is modified to use it.
Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
diff --git a/arch/arm/mach-at91/board-pcontrol-g20.c b/arch/arm/mach-at91/board-pcontrol-g20.c
index bba5a56..feb6578 100644
--- a/arch/arm/mach-at91/board-pcontrol-g20.c
+++ b/arch/arm/mach-at91/board-pcontrol-g20.c
@@ -31,6 +31,7 @@
#include <mach/board.h>
#include <mach/at91sam9_smc.h>
+#include <mach/stamp9g20.h>
#include "sam9_smc.h"
#include "generic.h"
@@ -38,11 +39,7 @@
static void __init pcontrol_g20_map_io(void)
{
- /* Initialize processor: 18.432 MHz crystal */
- at91sam9260_initialize(18432000);
-
- /* DGBU on ttyS0. (Rx, Tx) only TTL -> JTAG connector X7 17,19 ) */
- at91_register_uart(0, 0, 0);
+ stamp9g20_map_io();
/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback A2 */
at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS
@@ -54,9 +51,6 @@
/* USART2 on ttyS3. (Rx, Tx) 9bit-Bus Multidrop-mode X4 */
at91_register_uart(AT91SAM9260_ID_US4, 3, 0);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
@@ -66,38 +60,6 @@
}
-/*
- * NAND flash 512MiB 1,8V 8-bit, sector size 128 KiB
- */
-static struct atmel_nand_data __initdata nand_data = {
- .ale = 21,
- .cle = 22,
- .rdy_pin = AT91_PIN_PC13,
- .enable_pin = AT91_PIN_PC14,
-};
-
-/*
- * Bus timings; unit = 7.57ns
- */
-static struct sam9_smc_config __initdata nand_smc_config = {
- .ncs_read_setup = 0,
- .nrd_setup = 2,
- .ncs_write_setup = 0,
- .nwe_setup = 2,
-
- .ncs_read_pulse = 4,
- .nrd_pulse = 4,
- .ncs_write_pulse = 4,
- .nwe_pulse = 4,
-
- .read_cycle = 7,
- .write_cycle = 7,
-
- .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE
- | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
- .tdf_cycles = 3,
-};
-
static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { {
.ncs_read_setup = 16,
.nrd_setup = 18,
@@ -138,14 +100,6 @@
.tdf_cycles = 1,
} };
-static void __init add_device_nand(void)
-{
- /* configure chip-select 3 (NAND) */
- sam9_smc_configure(3, &nand_smc_config);
- at91_add_device_nand(&nand_data);
-}
-
-
static void __init add_device_pcontrol(void)
{
/* configure chip-select 4 (IO compatible to 8051 X4 ) */
@@ -156,23 +110,6 @@
/*
- * MCI (SD/MMC)
- * det_pin, wp_pin and vcc_pin are not connected
- */
-#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
-static struct mci_platform_data __initdata mmc_data = {
- .slot[0] = {
- .bus_width = 4,
- },
-};
-#else
-static struct at91_mmc_data __initdata mmc_data = {
- .wire4 = 1,
-};
-#endif
-
-
-/*
* USB Host port
*/
static struct at91_usbh_data __initdata usbh_data = {
@@ -265,42 +202,13 @@
};
-/*
- * Dallas 1-Wire DS2431
- */
-static struct w1_gpio_platform_data w1_gpio_pdata = {
- .pin = AT91_PIN_PA29,
- .is_open_drain = 1,
-};
-
-static struct platform_device w1_device = {
- .name = "w1-gpio",
- .id = -1,
- .dev.platform_data = &w1_gpio_pdata,
-};
-
-static void add_wire1(void)
-{
- at91_set_GPIO_periph(w1_gpio_pdata.pin, 1);
- at91_set_multi_drive(w1_gpio_pdata.pin, 1);
- platform_device_register(&w1_device);
-}
-
-
static void __init pcontrol_g20_board_init(void)
{
- at91_add_device_serial();
- add_device_nand();
-#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
- at91_add_device_mci(0, &mmc_data);
-#else
- at91_add_device_mmc(0, &mmc_data);
-#endif
+ stamp9g20_board_init();
at91_add_device_usbh(&usbh_data);
at91_add_device_eth(&macb_data);
at91_add_device_i2c(pcontrol_g20_i2c_devices,
ARRAY_SIZE(pcontrol_g20_i2c_devices));
- add_wire1();
add_device_pcontrol();
at91_add_device_spi(pcontrol_g20_spi_devices,
ARRAY_SIZE(pcontrol_g20_spi_devices));