mac80211: make PID rate control algorithm the default
This makes the new PID TX rate control algorithm the default instead of the
rc80211_simple rate control algorithm. The simple algorithm was flawed in
several ways: it wasn't responsive at all and didn't age the information it was
relying on properly. The PID algorithm allows us to tune characteristics such
as responsiveness by adjusting parameters and was found to generally behave
better.
The default algorithm can be overridden to select simple instead. Which
ever algorithm is the default is included as part of the mac80211
module automatically. The other algorithm (simple vs. pid) can
be selected for inclusion as well. If EMBEDDED is selected then
the choice is available to have no default specified and neither
algorithm included in mac80211. The default algorithm can be set
through a modparam.
While at it, mark rc80211-simple as deprecated, and schedule it
for removal.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/net/mac80211/Kconfig b/net/mac80211/Kconfig
index 9f8663b..297f4d9 100644
--- a/net/mac80211/Kconfig
+++ b/net/mac80211/Kconfig
@@ -13,29 +13,75 @@
This option enables the hardware independent IEEE 802.11
networking stack.
-config MAC80211_RCSIMPLE
- bool "'simple' rate control algorithm" if EMBEDDED
+config MAC80211_RC_DEFAULT_CHOICE
+ bool "Choose default rate control algorithm" if EMBEDDED
default y
depends on MAC80211
- help
- This option allows you to turn off the 'simple' rate
- control algorithm in mac80211. If you do turn it off,
- you absolutely need another rate control algorithm.
+ ---help---
+ This options enables selection of a default rate control
+ algorithm to be built into the mac80211 module. Alternate
+ rate control algorithms might be built into the mac80211
+ module as well.
- Say Y unless you know you will have another algorithm
- available.
+choice
+ prompt "Default rate control algorithm"
+ default MAC80211_RC_DEFAULT_PID
+ depends on MAC80211 && MAC80211_RC_DEFAULT_CHOICE
+ ---help---
+ This option selects the default rate control algorithm
+ mac80211 will use. Note that this default can still be
+ overriden through the ieee80211_default_rc_algo module
+ parameter.
-config MAC80211_RCPID
- bool "'PID' rate control algorithm" if EMBEDDED
+config MAC80211_RC_DEFAULT_PID
+ bool "PID controller based rate control algorithm"
+ select MAC80211_RC_PID
+ ---help---
+ Select the PID controller based rate control as the
+ default rate control algorithm. You should choose
+ this unless you know what you are doing.
+
+config MAC80211_RC_DEFAULT_SIMPLE
+ bool "Simple rate control algorithm"
+ select MAC80211_RC_SIMPLE
+ ---help---
+ Select the simple rate control as the default rate
+ control algorithm. Note that this is a non-responsive,
+ dumb algorithm. You should choose the PID rate control
+ instead.
+
+endchoice
+
+config MAC80211_RC_DEFAULT
+ string
+ depends on MAC80211
+ default "pid" if MAC80211_RC_DEFAULT_PID
+ default "simple" if MAC80211_RC_DEFAULT_SIMPLE
+ default ""
+
+config MAC80211_RC_PID
+ bool "PID controller based rate control algorithm"
default y
depends on MAC80211
- help
+ ---help---
This option enables a TX rate control algorithm for
mac80211 that uses a PID controller to select the TX
rate.
- Say Y unless you're sure you want to use a different
- rate control algorithm.
+ Say Y or M unless you're sure you want to use a
+ different rate control algorithm.
+
+config MAC80211_RC_SIMPLE
+ bool "Simple rate control algorithm (DEPRECATED)"
+ default n
+ depends on MAC80211
+ ---help---
+ This option enables a very simple, non-responsive TX
+ rate control algorithm. This algorithm is deprecated
+ and will be removed from the kernel in near future.
+ It has been replaced by the PID algorithm.
+
+ Say N unless you know what you are doing.
config MAC80211_LEDS
bool "Enable LED triggers"