diff --git a/Documentation/hwmon/lm85 b/Documentation/hwmon/lm85
index b98e0e0..83cd5bb 100644
--- a/Documentation/hwmon/lm85
+++ b/Documentation/hwmon/lm85
@@ -14,6 +14,10 @@
     Prefix: 'adt7463'
     Addresses scanned: I2C 0x2c, 0x2d, 0x2e
     Datasheet: http://www.onsemi.com/PowerSolutions/product.do?id=ADT7463
+  * Analog Devices ADT7468
+    Prefix: 'adt7468'
+    Addresses scanned: I2C 0x2c, 0x2d, 0x2e
+    Datasheet: http://www.onsemi.com/PowerSolutions/product.do?id=ADT7468
   * SMSC EMC6D100, SMSC EMC6D101
     Prefix: 'emc6d100'
     Addresses scanned: I2C 0x2c, 0x2d, 0x2e
@@ -34,7 +38,7 @@
 -----------
 
 This driver implements support for the National Semiconductor LM85 and
-compatible chips including the Analog Devices ADM1027, ADT7463 and
+compatible chips including the Analog Devices ADM1027, ADT7463, ADT7468 and
 SMSC EMC6D10x chips family.
 
 The LM85 uses the 2-wire interface compatible with the SMBUS 2.0
@@ -87,14 +91,15 @@
 optional filter for smoothing temperatures. The ADM1027 has the same
 config option but uses it to rate limit the changes to fan speed instead.
 
-The ADM1027 and ADT7463 have a 10-bit ADC and can therefore measure
-temperatures with 0.25 degC resolution. They also provide an offset to the
-temperature readings that is automatically applied during measurement.
-This offset can be used to zero out any errors due to traces and placement.
-The documentation says that the offset is in 0.25 degC steps, but in
-initial testing of the ADM1027 it was 1.00 degC steps. Analog Devices has
-confirmed this "bug". The ADT7463 is reported to work as described in the
-documentation. The current lm85 driver does not show the offset register.
+The ADM1027, ADT7463 and ADT7468 have a 10-bit ADC and can therefore
+measure temperatures with 0.25 degC resolution. They also provide an offset
+to the temperature readings that is automatically applied during
+measurement. This offset can be used to zero out any errors due to traces
+and placement. The documentation says that the offset is in 0.25 degC
+steps, but in initial testing of the ADM1027 it was 1.00 degC steps. Analog
+Devices has confirmed this "bug". The ADT7463 is reported to work as
+described in the documentation. The current lm85 driver does not show the
+offset register.
 
 See the vendor datasheets for more information. There is application note
 from National (AN-1260) with some additional information about the LM85.
@@ -125,17 +130,17 @@
 identifying the chip, the driver behaves no differently with regard to
 these two chips. The LM85B is recommended for new designs.
 
-The ADM1027 and ADT7463 chips have an optional SMBALERT output that can be
-used to signal the chipset in case a limit is exceeded or the temperature
-sensors fail. Individual sensor interrupts can be masked so they won't
-trigger SMBALERT. The SMBALERT output if configured replaces one of the other
-functions (PWM2 or IN0). This functionality is not implemented in current
-driver.
+The ADM1027, ADT7463 and ADT7468 chips have an optional SMBALERT output
+that can be used to signal the chipset in case a limit is exceeded or the
+temperature sensors fail. Individual sensor interrupts can be masked so
+they won't trigger SMBALERT. The SMBALERT output if configured replaces one
+of the other functions (PWM2 or IN0). This functionality is not implemented
+in current driver.
 
-The ADT7463 also has an optional THERM output/input which can be connected
-to the processor PROC_HOT output. If available, the autofan control
-dynamic Tmin feature can be enabled to keep the system temperature within
-spec (just?!) with the least possible fan noise.
+The ADT7463 and ADT7468 also have an optional THERM output/input which can
+be connected to the processor PROC_HOT output. If available, the autofan
+control dynamic Tmin feature can be enabled to keep the system temperature
+within spec (just?!) with the least possible fan noise.
 
 Configuration Notes
 -------------------
@@ -201,8 +206,8 @@
 measurements. These features are not currently supported by the lm85
 driver.
 
-In addition to the ADM1027 features, the ADT7463 also has Tmin control
-and THERM asserted counts. Automatic Tmin control acts to adjust the
-Tmin value to maintain the measured temperature sensor at a specified
-temperature. There isn't much documentation on this feature in the
-ADT7463 data sheet. This is not supported by current driver.
+In addition to the ADM1027 features, the ADT7463 and ADT7468 also have
+Tmin control and THERM asserted counts. Automatic Tmin control acts to
+adjust the Tmin value to maintain the measured temperature sensor at a
+specified temperature. There isn't much documentation on this feature in
+the ADT7463 data sheet. This is not supported by current driver.