Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-bigbox-bootmem-v3
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-bigbox-bootmem-v3:
x86_64/mm: check and print vmemmap allocation continuous
x86_64: fix setup_node_bootmem to support big mem excluding with memmap
x86_64: make reserve_bootmem_generic() use new reserve_bootmem()
mm: allow reserve_bootmem() cross nodes
mm: offset align in alloc_bootmem()
mm: fix alloc_bootmem_core to use fast searching for all nodes
mm: make mem_map allocation continuous
diff --git a/Documentation/mips/AU1xxx_IDE.README b/Documentation/mips/AU1xxx_IDE.README
index 5c83341..25a6ed1 100644
--- a/Documentation/mips/AU1xxx_IDE.README
+++ b/Documentation/mips/AU1xxx_IDE.README
@@ -46,8 +46,6 @@
a) 'include/asm-mips/mach-au1x00/au1xxx_ide.h'
containes : struct _auide_hwif
- struct drive_list_entry dma_white_list
- struct drive_list_entry dma_black_list
timing parameters for PIO mode 0/1/2/3/4
timing parameters for MWDMA 0/1/2
@@ -63,12 +61,6 @@
CONFIG_BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ - maximum transfer size
per descriptor
-If MWDMA is enabled and the connected hard disc is not on the white list, the
-kernel switches to a "safe mwdma mode" at boot time. In this mode the IDE
-performance is substantial slower then in full speed mwdma. In this case
-please add your hard disc to the white list (follow instruction from 'ADD NEW
-HARD DISC TO WHITE OR BLACK LIST' section).
-
SUPPORTED IDE MODES
-------------------
@@ -120,44 +112,6 @@
Also undefine 'IDE_AU1XXX_BURSTMODE' in 'drivers/ide/mips/au1xxx-ide.c' to
disable the burst support on DBDMA controller.
-ADD NEW HARD DISC TO WHITE OR BLACK LIST
-----------------------------------------
-
-Step 1 : detect the model name of your hard disc
-
- a) connect your hard disc to the AU1XXX
-
- b) boot your kernel and get the hard disc model.
-
- Example boot log:
-
- --snipped--
- Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
- ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
- Au1xxx IDE(builtin) configured for MWDMA2
- Probing IDE interface ide0...
- hda: Maxtor 6E040L0, ATA DISK drive
- ide0 at 0xac800000-0xac800007,0xac8001c0 on irq 64
- hda: max request size: 64KiB
- hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=65535/16/63, (U)DMA
- --snipped--
-
- In this example 'Maxtor 6E040L0'.
-
-Step 2 : edit 'include/asm-mips/mach-au1x00/au1xxx_ide.h'
-
- Add your hard disc to the dma_white_list or dma_black_list structur.
-
-Step 3 : Recompile the kernel
-
- Enable MWDMA support in the kernel configuration. Recompile the kernel and
- reboot.
-
-Step 4 : Tests
-
- If you have add a hard disc to the white list, please run some stress tests
- for verification.
-
ACKNOWLEDGMENTS
---------------
diff --git a/arch/um/Kconfig.x86_64 b/arch/um/Kconfig.x86_64
index 3fbe69e..5696e7b 100644
--- a/arch/um/Kconfig.x86_64
+++ b/arch/um/Kconfig.x86_64
@@ -1,3 +1,10 @@
+
+menu "Host processor type and features"
+
+source "arch/x86/Kconfig.cpu"
+
+endmenu
+
config UML_X86
bool
default y
diff --git a/arch/um/os-Linux/helper.c b/arch/um/os-Linux/helper.c
index f4bd349..f25c29a 100644
--- a/arch/um/os-Linux/helper.c
+++ b/arch/um/os-Linux/helper.c
@@ -14,6 +14,7 @@
#include "os.h"
#include "um_malloc.h"
#include "user.h"
+#include <linux/limits.h>
struct helper_data {
void (*pre_exec)(void*);
diff --git a/arch/um/sys-i386/Makefile b/arch/um/sys-i386/Makefile
index 964dc1a0..598b5c1 100644
--- a/arch/um/sys-i386/Makefile
+++ b/arch/um/sys-i386/Makefile
@@ -6,7 +6,7 @@
ptrace_user.o setjmp.o signal.o stub.o stub_segv.o syscalls.o sysrq.o \
sys_call_table.o tls.o
-subarch-obj-y = lib/bitops_32.o lib/semaphore_32.o lib/string_32.o
+subarch-obj-y = lib/semaphore_32.o lib/string_32.o
subarch-obj-$(CONFIG_HIGHMEM) += mm/highmem_32.o
subarch-obj-$(CONFIG_MODULES) += kernel/module_32.o
diff --git a/arch/um/sys-x86_64/Makefile b/arch/um/sys-x86_64/Makefile
index 3c22de5..c8b4cce 100644
--- a/arch/um/sys-x86_64/Makefile
+++ b/arch/um/sys-x86_64/Makefile
@@ -10,7 +10,7 @@
obj-$(CONFIG_MODULES) += um_module.o
-subarch-obj-y = lib/bitops_64.o lib/csum-partial_64.o lib/memcpy_64.o lib/thunk_64.o
+subarch-obj-y = lib/csum-partial_64.o lib/memcpy_64.o lib/thunk_64.o
subarch-obj-$(CONFIG_MODULES) += kernel/module_64.o
ldt-y = ../sys-i386/ldt.o
diff --git a/arch/x86/Kconfig.cpu b/arch/x86/Kconfig.cpu
index 4da3cdb..7ef18b0 100644
--- a/arch/x86/Kconfig.cpu
+++ b/arch/x86/Kconfig.cpu
@@ -278,6 +278,11 @@
endchoice
+config X86_CPU
+ def_bool y
+ select GENERIC_FIND_FIRST_BIT
+ select GENERIC_FIND_NEXT_BIT
+
config X86_GENERIC
bool "Generic x86 support"
depends on X86_32
@@ -398,7 +403,7 @@
# generates cmov.
config X86_CMOV
def_bool y
- depends on (MK7 || MPENTIUM4 || MPENTIUMM || MPENTIUMIII || MPENTIUMII || M686 || MVIAC3_2 || MVIAC7)
+ depends on (MK7 || MPENTIUM4 || MPENTIUMM || MPENTIUMIII || MPENTIUMII || M686 || MVIAC3_2 || MVIAC7 || X86_64)
config X86_MINIMUM_CPU_FAMILY
int
diff --git a/arch/x86/lib/Makefile b/arch/x86/lib/Makefile
index 25df1c1..76f60f5 100644
--- a/arch/x86/lib/Makefile
+++ b/arch/x86/lib/Makefile
@@ -11,7 +11,7 @@
ifeq ($(CONFIG_X86_32),y)
lib-y += checksum_32.o
lib-y += strstr_32.o
- lib-y += bitops_32.o semaphore_32.o string_32.o
+ lib-y += semaphore_32.o string_32.o
lib-$(CONFIG_X86_USE_3DNOW) += mmx_32.o
else
@@ -21,7 +21,6 @@
lib-y += csum-partial_64.o csum-copy_64.o csum-wrappers_64.o
lib-y += thunk_64.o clear_page_64.o copy_page_64.o
- lib-y += bitops_64.o
lib-y += memmove_64.o memset_64.o
lib-y += copy_user_64.o rwlock_64.o copy_user_nocache_64.o
endif
diff --git a/arch/x86/lib/bitops_32.c b/arch/x86/lib/bitops_32.c
deleted file mode 100644
index b654404..0000000
--- a/arch/x86/lib/bitops_32.c
+++ /dev/null
@@ -1,70 +0,0 @@
-#include <linux/bitops.h>
-#include <linux/module.h>
-
-/**
- * find_next_bit - find the next set bit in a memory region
- * @addr: The address to base the search on
- * @offset: The bitnumber to start searching at
- * @size: The maximum size to search
- */
-int find_next_bit(const unsigned long *addr, int size, int offset)
-{
- const unsigned long *p = addr + (offset >> 5);
- int set = 0, bit = offset & 31, res;
-
- if (bit) {
- /*
- * Look for nonzero in the first 32 bits:
- */
- __asm__("bsfl %1,%0\n\t"
- "jne 1f\n\t"
- "movl $32, %0\n"
- "1:"
- : "=r" (set)
- : "r" (*p >> bit));
- if (set < (32 - bit))
- return set + offset;
- set = 32 - bit;
- p++;
- }
- /*
- * No set bit yet, search remaining full words for a bit
- */
- res = find_first_bit (p, size - 32 * (p - addr));
- return (offset + set + res);
-}
-EXPORT_SYMBOL(find_next_bit);
-
-/**
- * find_next_zero_bit - find the first zero bit in a memory region
- * @addr: The address to base the search on
- * @offset: The bitnumber to start searching at
- * @size: The maximum size to search
- */
-int find_next_zero_bit(const unsigned long *addr, int size, int offset)
-{
- const unsigned long *p = addr + (offset >> 5);
- int set = 0, bit = offset & 31, res;
-
- if (bit) {
- /*
- * Look for zero in the first 32 bits.
- */
- __asm__("bsfl %1,%0\n\t"
- "jne 1f\n\t"
- "movl $32, %0\n"
- "1:"
- : "=r" (set)
- : "r" (~(*p >> bit)));
- if (set < (32 - bit))
- return set + offset;
- set = 32 - bit;
- p++;
- }
- /*
- * No zero yet, search remaining full bytes for a zero
- */
- res = find_first_zero_bit(p, size - 32 * (p - addr));
- return (offset + set + res);
-}
-EXPORT_SYMBOL(find_next_zero_bit);
diff --git a/arch/x86/lib/bitops_64.c b/arch/x86/lib/bitops_64.c
deleted file mode 100644
index 0e8f491..0000000
--- a/arch/x86/lib/bitops_64.c
+++ /dev/null
@@ -1,175 +0,0 @@
-#include <linux/bitops.h>
-
-#undef find_first_zero_bit
-#undef find_next_zero_bit
-#undef find_first_bit
-#undef find_next_bit
-
-static inline long
-__find_first_zero_bit(const unsigned long * addr, unsigned long size)
-{
- long d0, d1, d2;
- long res;
-
- /*
- * We must test the size in words, not in bits, because
- * otherwise incoming sizes in the range -63..-1 will not run
- * any scasq instructions, and then the flags used by the je
- * instruction will have whatever random value was in place
- * before. Nobody should call us like that, but
- * find_next_zero_bit() does when offset and size are at the
- * same word and it fails to find a zero itself.
- */
- size += 63;
- size >>= 6;
- if (!size)
- return 0;
- asm volatile(
- " repe; scasq\n"
- " je 1f\n"
- " xorq -8(%%rdi),%%rax\n"
- " subq $8,%%rdi\n"
- " bsfq %%rax,%%rdx\n"
- "1: subq %[addr],%%rdi\n"
- " shlq $3,%%rdi\n"
- " addq %%rdi,%%rdx"
- :"=d" (res), "=&c" (d0), "=&D" (d1), "=&a" (d2)
- :"0" (0ULL), "1" (size), "2" (addr), "3" (-1ULL),
- [addr] "S" (addr) : "memory");
- /*
- * Any register would do for [addr] above, but GCC tends to
- * prefer rbx over rsi, even though rsi is readily available
- * and doesn't have to be saved.
- */
- return res;
-}
-
-/**
- * find_first_zero_bit - find the first zero bit in a memory region
- * @addr: The address to start the search at
- * @size: The maximum size to search
- *
- * Returns the bit-number of the first zero bit, not the number of the byte
- * containing a bit.
- */
-long find_first_zero_bit(const unsigned long * addr, unsigned long size)
-{
- return __find_first_zero_bit (addr, size);
-}
-
-/**
- * find_next_zero_bit - find the next zero bit in a memory region
- * @addr: The address to base the search on
- * @offset: The bitnumber to start searching at
- * @size: The maximum size to search
- */
-long find_next_zero_bit (const unsigned long * addr, long size, long offset)
-{
- const unsigned long * p = addr + (offset >> 6);
- unsigned long set = 0;
- unsigned long res, bit = offset&63;
-
- if (bit) {
- /*
- * Look for zero in first word
- */
- asm("bsfq %1,%0\n\t"
- "cmoveq %2,%0"
- : "=r" (set)
- : "r" (~(*p >> bit)), "r"(64L));
- if (set < (64 - bit))
- return set + offset;
- set = 64 - bit;
- p++;
- }
- /*
- * No zero yet, search remaining full words for a zero
- */
- res = __find_first_zero_bit (p, size - 64 * (p - addr));
-
- return (offset + set + res);
-}
-
-static inline long
-__find_first_bit(const unsigned long * addr, unsigned long size)
-{
- long d0, d1;
- long res;
-
- /*
- * We must test the size in words, not in bits, because
- * otherwise incoming sizes in the range -63..-1 will not run
- * any scasq instructions, and then the flags used by the jz
- * instruction will have whatever random value was in place
- * before. Nobody should call us like that, but
- * find_next_bit() does when offset and size are at the same
- * word and it fails to find a one itself.
- */
- size += 63;
- size >>= 6;
- if (!size)
- return 0;
- asm volatile(
- " repe; scasq\n"
- " jz 1f\n"
- " subq $8,%%rdi\n"
- " bsfq (%%rdi),%%rax\n"
- "1: subq %[addr],%%rdi\n"
- " shlq $3,%%rdi\n"
- " addq %%rdi,%%rax"
- :"=a" (res), "=&c" (d0), "=&D" (d1)
- :"0" (0ULL), "1" (size), "2" (addr),
- [addr] "r" (addr) : "memory");
- return res;
-}
-
-/**
- * find_first_bit - find the first set bit in a memory region
- * @addr: The address to start the search at
- * @size: The maximum size to search
- *
- * Returns the bit-number of the first set bit, not the number of the byte
- * containing a bit.
- */
-long find_first_bit(const unsigned long * addr, unsigned long size)
-{
- return __find_first_bit(addr,size);
-}
-
-/**
- * find_next_bit - find the first set bit in a memory region
- * @addr: The address to base the search on
- * @offset: The bitnumber to start searching at
- * @size: The maximum size to search
- */
-long find_next_bit(const unsigned long * addr, long size, long offset)
-{
- const unsigned long * p = addr + (offset >> 6);
- unsigned long set = 0, bit = offset & 63, res;
-
- if (bit) {
- /*
- * Look for nonzero in the first 64 bits:
- */
- asm("bsfq %1,%0\n\t"
- "cmoveq %2,%0\n\t"
- : "=r" (set)
- : "r" (*p >> bit), "r" (64L));
- if (set < (64 - bit))
- return set + offset;
- set = 64 - bit;
- p++;
- }
- /*
- * No set bit yet, search remaining full words for a bit
- */
- res = __find_first_bit (p, size - 64 * (p - addr));
- return (offset + set + res);
-}
-
-#include <linux/module.h>
-
-EXPORT_SYMBOL(find_next_bit);
-EXPORT_SYMBOL(find_first_bit);
-EXPORT_SYMBOL(find_first_zero_bit);
-EXPORT_SYMBOL(find_next_zero_bit);
diff --git a/drivers/ide/arm/bast-ide.c b/drivers/ide/arm/bast-ide.c
index a80b957..d158f57 100644
--- a/drivers/ide/arm/bast-ide.c
+++ b/drivers/ide/arm/bast-ide.c
@@ -55,8 +55,7 @@
ide_init_port_data(hwif, i);
ide_init_port_hw(hwif, &hw);
- hwif->mmio = 1;
- hwif->quirkproc = NULL;
+ hwif->port_ops = NULL;
idx[0] = i;
diff --git a/drivers/ide/arm/icside.c b/drivers/ide/arm/icside.c
index fd12bbe..7d642f4 100644
--- a/drivers/ide/arm/icside.c
+++ b/drivers/ide/arm/icside.c
@@ -191,6 +191,10 @@
local_irq_restore(flags);
}
+static const struct ide_port_ops icside_v6_no_dma_port_ops = {
+ .maskproc = icside_maskproc,
+};
+
#ifdef CONFIG_BLK_DEV_IDEDMA_ICS
/*
* SG-DMA support.
@@ -266,6 +270,11 @@
ide_xfer_verbose(xfer_mode), 2000 / drive->drive_data);
}
+static const struct ide_port_ops icside_v6_port_ops = {
+ .set_dma_mode = icside_set_dma_mode,
+ .maskproc = icside_maskproc,
+};
+
static void icside_dma_host_set(ide_drive_t *drive, int on)
{
}
@@ -375,25 +384,33 @@
printk(KERN_ERR "%s: IRQ lost\n", drive->name);
}
-static void icside_dma_init(ide_hwif_t *hwif)
+static int icside_dma_init(ide_hwif_t *hwif, const struct ide_port_info *d)
{
hwif->dmatable_cpu = NULL;
hwif->dmatable_dma = 0;
- hwif->set_dma_mode = icside_set_dma_mode;
- hwif->dma_host_set = icside_dma_host_set;
- hwif->dma_setup = icside_dma_setup;
- hwif->dma_exec_cmd = icside_dma_exec_cmd;
- hwif->dma_start = icside_dma_start;
- hwif->ide_dma_end = icside_dma_end;
- hwif->ide_dma_test_irq = icside_dma_test_irq;
- hwif->dma_timeout = icside_dma_timeout;
- hwif->dma_lost_irq = icside_dma_lost_irq;
+ return 0;
}
+
+static const struct ide_dma_ops icside_v6_dma_ops = {
+ .dma_host_set = icside_dma_host_set,
+ .dma_setup = icside_dma_setup,
+ .dma_exec_cmd = icside_dma_exec_cmd,
+ .dma_start = icside_dma_start,
+ .dma_end = icside_dma_end,
+ .dma_test_irq = icside_dma_test_irq,
+ .dma_timeout = icside_dma_timeout,
+ .dma_lost_irq = icside_dma_lost_irq,
+};
#else
-#define icside_dma_init(hwif) (0)
+#define icside_v6_dma_ops NULL
#endif
+static int icside_dma_off_init(ide_hwif_t *hwif, const struct ide_port_info *d)
+{
+ return -EOPNOTSUPP;
+}
+
static ide_hwif_t *
icside_setup(void __iomem *base, struct cardinfo *info, struct expansion_card *ec)
{
@@ -408,7 +425,6 @@
* Ensure we're using MMIO
*/
default_hwif_mmiops(hwif);
- hwif->mmio = 1;
for (i = IDE_DATA_OFFSET; i <= IDE_STATUS_OFFSET; i++) {
hwif->io_ports[i] = port;
@@ -416,7 +432,6 @@
}
hwif->io_ports[IDE_CONTROL_OFFSET] = (unsigned long)base + info->ctrloffset;
hwif->irq = ec->irq;
- hwif->noprobe = 0;
hwif->chipset = ide_acorn;
hwif->gendev.parent = &ec->dev;
hwif->dev = &ec->dev;
@@ -462,8 +477,10 @@
}
static const struct ide_port_info icside_v6_port_info __initdata = {
+ .init_dma = icside_dma_off_init,
+ .port_ops = &icside_v6_no_dma_port_ops,
+ .dma_ops = &icside_v6_dma_ops,
.host_flags = IDE_HFLAG_SERIALIZE |
- IDE_HFLAG_NO_DMA | /* no SFF-style DMA */
IDE_HFLAG_NO_AUTOTUNE,
.mwdma_mask = ATA_MWDMA2,
.swdma_mask = ATA_SWDMA2,
@@ -526,7 +543,6 @@
state->hwif[0] = hwif;
state->hwif[1] = mate;
- hwif->maskproc = icside_maskproc;
hwif->hwif_data = state;
hwif->config_data = (unsigned long)ioc_base;
hwif->select_data = sel;
@@ -537,10 +553,10 @@
mate->select_data = sel | 1;
if (ec->dma != NO_DMA && !request_dma(ec->dma, hwif->name)) {
- icside_dma_init(hwif);
- icside_dma_init(mate);
- } else
- d.mwdma_mask = d.swdma_mask = 0;
+ d.init_dma = icside_dma_init;
+ d.port_ops = &icside_v6_dma_port_ops;
+ d.dma_ops = NULL;
+ }
idx[0] = hwif->index;
idx[1] = mate->index;
diff --git a/drivers/ide/arm/ide_arm.c b/drivers/ide/arm/ide_arm.c
index 82643df..4263ffd 100644
--- a/drivers/ide/arm/ide_arm.c
+++ b/drivers/ide/arm/ide_arm.c
@@ -14,6 +14,8 @@
#include <asm/mach-types.h>
#include <asm/irq.h>
+#define DRV_NAME "ide_arm"
+
#ifdef CONFIG_ARCH_CLPS7500
# include <asm/arch/hardware.h>
#
@@ -28,10 +30,24 @@
{
ide_hwif_t *hwif;
hw_regs_t hw;
+ unsigned long base = IDE_ARM_IO, ctl = IDE_ARM_IO + 0x206;
u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
+ if (!request_region(base, 8, DRV_NAME)) {
+ printk(KERN_ERR "%s: I/O resource 0x%lX-0x%lX not free.\n",
+ DRV_NAME, base, base + 7);
+ return -EBUSY;
+ }
+
+ if (!request_region(ctl, 1, DRV_NAME)) {
+ printk(KERN_ERR "%s: I/O resource 0x%lX not free.\n",
+ DRV_NAME, ctl);
+ release_region(base, 8);
+ return -EBUSY;
+ }
+
memset(&hw, 0, sizeof(hw));
- ide_std_init_ports(&hw, IDE_ARM_IO, IDE_ARM_IO + 0x206);
+ ide_std_init_ports(&hw, base, ctl);
hw.irq = IDE_ARM_IRQ;
hwif = ide_find_port();
diff --git a/drivers/ide/arm/palm_bk3710.c b/drivers/ide/arm/palm_bk3710.c
index 666df77..8fa34e2 100644
--- a/drivers/ide/arm/palm_bk3710.c
+++ b/drivers/ide/arm/palm_bk3710.c
@@ -317,17 +317,31 @@
return ATA_CBL_PATA80;
}
-static void __devinit palm_bk3710_init_hwif(ide_hwif_t *hwif)
+static int __devinit palm_bk3710_init_dma(ide_hwif_t *hwif,
+ const struct ide_port_info *d)
{
- hwif->set_pio_mode = palm_bk3710_set_pio_mode;
- hwif->set_dma_mode = palm_bk3710_set_dma_mode;
+ unsigned long base =
+ hwif->io_ports[IDE_DATA_OFFSET] - IDE_PALM_ATA_PRI_REG_OFFSET;
- hwif->cable_detect = palm_bk3710_cable_detect;
+ printk(KERN_INFO " %s: MMIO-DMA\n", hwif->name);
+
+ if (ide_allocate_dma_engine(hwif))
+ return -1;
+
+ ide_setup_dma(hwif, base);
+
+ return 0;
}
+static const struct ide_port_ops palm_bk3710_ports_ops = {
+ .set_pio_mode = palm_bk3710_set_pio_mode,
+ .set_dma_mode = palm_bk3710_set_dma_mode,
+ .cable_detect = palm_bk3710_cable_detect,
+};
+
static const struct ide_port_info __devinitdata palm_bk3710_port_info = {
- .init_hwif = palm_bk3710_init_hwif,
- .host_flags = IDE_HFLAG_NO_DMA, /* hack (no PCI) */
+ .init_dma = palm_bk3710_init_dma,
+ .port_ops = &palm_bk3710_ports_ops,
.pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA4, /* (input clk 99MHz) */
.mwdma_mask = ATA_MWDMA2,
@@ -394,8 +408,6 @@
hwif->mmio = 1;
default_hwif_mmiops(hwif);
- ide_setup_dma(hwif, mem->start);
-
idx[0] = i;
ide_device_add(idx, &palm_bk3710_port_info);
diff --git a/drivers/ide/arm/rapide.c b/drivers/ide/arm/rapide.c
index 2c3d0ec..c0581bd 100644
--- a/drivers/ide/arm/rapide.c
+++ b/drivers/ide/arm/rapide.c
@@ -53,7 +53,6 @@
ide_init_port_hw(hwif, &hw);
- hwif->mmio = 1;
default_hwif_mmiops(hwif);
idx[0] = hwif->index;
diff --git a/drivers/ide/cris/ide-cris.c b/drivers/ide/cris/ide-cris.c
index 790a775..a62ca75 100644
--- a/drivers/ide/cris/ide-cris.c
+++ b/drivers/ide/cris/ide-cris.c
@@ -673,11 +673,6 @@
return (unsigned char)cris_ide_inw(reg);
}
-static int cris_dma_end (ide_drive_t *drive);
-static int cris_dma_setup (ide_drive_t *drive);
-static void cris_dma_exec_cmd (ide_drive_t *drive, u8 command);
-static int cris_dma_test_irq(ide_drive_t *drive);
-static void cris_dma_start(ide_drive_t *drive);
static void cris_ide_input_data (ide_drive_t *drive, void *, unsigned int);
static void cris_ide_output_data (ide_drive_t *drive, void *, unsigned int);
static void cris_atapi_input_bytes(ide_drive_t *drive, void *, unsigned int);
@@ -782,8 +777,17 @@
hw->ack_intr = cris_ide_ack_intr;
}
+static const struct ide_port_ops cris_port_ops = {
+ .set_pio_mode = cris_set_pio_mode,
+ .set_dma_mode = cris_set_dma_mode,
+};
+
+static const struct ide_dma_ops cris_dma_ops;
+
static const struct ide_port_info cris_port_info __initdata = {
.chipset = ide_etrax100,
+ .port_ops = &cris_port_ops,
+ .dma_ops = &cris_dma_ops,
.host_flags = IDE_HFLAG_NO_ATAPI_DMA |
IDE_HFLAG_NO_DMA, /* no SFF-style DMA */
.pio_mask = ATA_PIO4,
@@ -809,19 +813,11 @@
continue;
ide_init_port_data(hwif, hwif->index);
ide_init_port_hw(hwif, &hw);
- hwif->mmio = 1;
- hwif->set_pio_mode = &cris_set_pio_mode;
- hwif->set_dma_mode = &cris_set_dma_mode;
+
hwif->ata_input_data = &cris_ide_input_data;
hwif->ata_output_data = &cris_ide_output_data;
hwif->atapi_input_bytes = &cris_atapi_input_bytes;
hwif->atapi_output_bytes = &cris_atapi_output_bytes;
- hwif->dma_host_set = &cris_dma_host_set;
- hwif->ide_dma_end = &cris_dma_end;
- hwif->dma_setup = &cris_dma_setup;
- hwif->dma_exec_cmd = &cris_dma_exec_cmd;
- hwif->ide_dma_test_irq = &cris_dma_test_irq;
- hwif->dma_start = &cris_dma_start;
hwif->OUTB = &cris_ide_outb;
hwif->OUTW = &cris_ide_outw;
hwif->OUTBSYNC = &cris_ide_outbsync;
@@ -1076,6 +1072,15 @@
}
}
+static const struct ide_dma_ops cris_dma_ops = {
+ .dma_host_set = cris_dma_host_set,
+ .dma_setup = cris_dma_setup,
+ .dma_exec_cmd = cris_dma_exec_cmd,
+ .dma_start = cris_dma_start,
+ .dma_end = cris_dma_end,
+ .dma_test_irq = cris_dma_test_irq,
+};
+
module_init(init_e100_ide);
MODULE_LICENSE("GPL");
diff --git a/drivers/ide/h8300/ide-h8300.c b/drivers/ide/h8300/ide-h8300.c
index 92b02b9..0708b29 100644
--- a/drivers/ide/h8300/ide-h8300.c
+++ b/drivers/ide/h8300/ide-h8300.c
@@ -74,7 +74,6 @@
{
default_hwif_iops(hwif);
- hwif->mmio = 1;
hwif->OUTW = mm_outw;
hwif->OUTSW = mm_outsw;
hwif->INW = mm_inw;
diff --git a/drivers/ide/ide-acpi.c b/drivers/ide/ide-acpi.c
index 0f6fb6b7..e4ad26e 100644
--- a/drivers/ide/ide-acpi.c
+++ b/drivers/ide/ide-acpi.c
@@ -55,7 +55,7 @@
/* note: adds function name and KERN_DEBUG */
#ifdef DEBUGGING
#define DEBPRINT(fmt, args...) \
- printk(KERN_DEBUG "%s: " fmt, __FUNCTION__, ## args)
+ printk(KERN_DEBUG "%s: " fmt, __func__, ## args)
#else
#define DEBPRINT(fmt, args...) do {} while (0)
#endif /* DEBUGGING */
@@ -309,7 +309,7 @@
if (ACPI_FAILURE(status)) {
printk(KERN_DEBUG
"%s: Run _GTF error: status = 0x%x\n",
- __FUNCTION__, status);
+ __func__, status);
goto out;
}
@@ -335,7 +335,7 @@
out_obj->buffer.length % REGS_PER_GTF) {
printk(KERN_ERR
"%s: unexpected GTF length (%d) or addr (0x%p)\n",
- __FUNCTION__, out_obj->buffer.length,
+ __func__, out_obj->buffer.length,
out_obj->buffer.pointer);
err = -ENOENT;
kfree(output.pointer);
@@ -384,7 +384,7 @@
err = ide_no_data_taskfile(drive, &args);
if (err)
printk(KERN_ERR "%s: ide_no_data_taskfile failed: %u\n",
- __FUNCTION__, err);
+ __func__, err);
return err;
}
@@ -422,7 +422,7 @@
if (gtf_length % REGS_PER_GTF) {
printk(KERN_ERR "%s: unexpected GTF length (%d)\n",
- __FUNCTION__, gtf_length);
+ __func__, gtf_length);
goto out;
}
@@ -547,7 +547,7 @@
printk(KERN_ERR
"%s: unexpected _GTM length (0x%x)[should be 0x%zx] or "
"addr (0x%p)\n",
- __FUNCTION__, out_obj->buffer.length,
+ __func__, out_obj->buffer.length,
sizeof(struct GTM_buffer), out_obj->buffer.pointer);
return;
}
diff --git a/drivers/ide/ide-cd.c b/drivers/ide/ide-cd.c
index 1afd95a..ad98432 100644
--- a/drivers/ide/ide-cd.c
+++ b/drivers/ide/ide-cd.c
@@ -39,12 +39,13 @@
#include <linux/mutex.h>
#include <linux/bcd.h>
-#include <scsi/scsi.h> /* For SCSI -> ATAPI command conversion */
+/* For SCSI -> ATAPI command conversion */
+#include <scsi/scsi.h>
-#include <asm/irq.h>
-#include <asm/io.h>
+#include <linux/irq.h>
+#include <linux/io.h>
#include <asm/byteorder.h>
-#include <asm/uaccess.h>
+#include <linux/uaccess.h>
#include <asm/unaligned.h>
#include "ide-cd.h"
@@ -77,12 +78,11 @@
mutex_unlock(&idecd_ref_mutex);
}
-/****************************************************************************
+/*
* Generic packet command support and error handling routines.
*/
-/* Mark that we've seen a media change, and invalidate our internal
- buffers. */
+/* Mark that we've seen a media change and invalidate our internal buffers. */
static void cdrom_saw_media_change(ide_drive_t *drive)
{
struct cdrom_info *cd = drive->driver_data;
@@ -105,9 +105,8 @@
break;
case NOT_READY:
/*
- * don't care about tray state messages for
- * e.g. capacity commands or in-progress or
- * becoming ready
+ * don't care about tray state messages for e.g. capacity
+ * commands or in-progress or becoming ready
*/
if (sense->asc == 0x3a || sense->asc == 0x04)
break;
@@ -115,8 +114,8 @@
break;
case ILLEGAL_REQUEST:
/*
- * don't log START_STOP unit with LoEj set, since
- * we cannot reliably check if drive can auto-close
+ * don't log START_STOP unit with LoEj set, since we cannot
+ * reliably check if drive can auto-close
*/
if (rq->cmd[0] == GPCMD_START_STOP_UNIT && sense->asc == 0x24)
break;
@@ -124,9 +123,9 @@
break;
case UNIT_ATTENTION:
/*
- * Make good and sure we've seen this potential media
- * change. Some drives (i.e. Creative) fail to present
- * the correct sense key in the error register.
+ * Make good and sure we've seen this potential media change.
+ * Some drives (i.e. Creative) fail to present the correct sense
+ * key in the error register.
*/
cdrom_saw_media_change(drive);
break;
@@ -137,8 +136,7 @@
return log;
}
-static
-void cdrom_analyze_sense_data(ide_drive_t *drive,
+static void cdrom_analyze_sense_data(ide_drive_t *drive,
struct request *failed_command,
struct request_sense *sense)
{
@@ -151,15 +149,16 @@
return;
/*
- * If a read toc is executed for a CD-R or CD-RW medium where
- * the first toc has not been recorded yet, it will fail with
- * 05/24/00 (which is a confusing error)
+ * If a read toc is executed for a CD-R or CD-RW medium where the first
+ * toc has not been recorded yet, it will fail with 05/24/00 (which is a
+ * confusing error)
*/
if (failed_command && failed_command->cmd[0] == GPCMD_READ_TOC_PMA_ATIP)
if (sense->sense_key == 0x05 && sense->asc == 0x24)
return;
- if (sense->error_code == 0x70) { /* Current Error */
+ /* current error */
+ if (sense->error_code == 0x70) {
switch (sense->sense_key) {
case MEDIUM_ERROR:
case VOLUME_OVERFLOW:
@@ -178,25 +177,23 @@
if (bio_sectors < 4)
bio_sectors = 4;
if (drive->queue->hardsect_size == 2048)
- sector <<= 2; /* Device sector size is 2K */
+ /* device sector size is 2K */
+ sector <<= 2;
sector &= ~(bio_sectors - 1);
valid = (sector - failed_command->sector) << 9;
if (valid < 0)
valid = 0;
if (sector < get_capacity(info->disk) &&
- drive->probed_capacity - sector < 4 * 75) {
+ drive->probed_capacity - sector < 4 * 75)
set_capacity(info->disk, sector);
- }
}
}
ide_cd_log_error(drive->name, failed_command, sense);
}
-/*
- * Initialize a ide-cd packet command request
- */
+/* Initialize a ide-cd packet command request */
void ide_cd_init_rq(ide_drive_t *drive, struct request *rq)
{
struct cdrom_info *cd = drive->driver_data;
@@ -220,7 +217,8 @@
rq->data = sense;
rq->cmd[0] = GPCMD_REQUEST_SENSE;
- rq->cmd[4] = rq->data_len = 18;
+ rq->cmd[4] = 18;
+ rq->data_len = 18;
rq->cmd_type = REQ_TYPE_SENSE;
@@ -252,7 +250,7 @@
}
cdrom_analyze_sense_data(drive, failed, sense);
/*
- * now end failed request
+ * now end the failed request
*/
if (blk_fs_request(failed)) {
if (ide_end_dequeued_request(drive, failed, 0,
@@ -280,21 +278,24 @@
ide_end_request(drive, uptodate, nsectors);
}
-static void ide_dump_status_no_sense(ide_drive_t *drive, const char *msg, u8 stat)
+static void ide_dump_status_no_sense(ide_drive_t *drive, const char *msg, u8 st)
{
- if (stat & 0x80)
+ if (st & 0x80)
return;
- ide_dump_status(drive, msg, stat);
+ ide_dump_status(drive, msg, st);
}
-/* Returns 0 if the request should be continued.
- Returns 1 if the request was ended. */
+/*
+ * Returns:
+ * 0: if the request should be continued.
+ * 1: if the request was ended.
+ */
static int cdrom_decode_status(ide_drive_t *drive, int good_stat, int *stat_ret)
{
struct request *rq = HWGROUP(drive)->rq;
int stat, err, sense_key;
- /* Check for errors. */
+ /* check for errors */
stat = ide_read_status(drive);
if (stat_ret)
@@ -303,20 +304,22 @@
if (OK_STAT(stat, good_stat, BAD_R_STAT))
return 0;
- /* Get the IDE error register. */
+ /* get the IDE error register */
err = ide_read_error(drive);
sense_key = err >> 4;
if (rq == NULL) {
- printk("%s: missing rq in cdrom_decode_status\n", drive->name);
+ printk(KERN_ERR "%s: missing rq in %s\n",
+ drive->name, __func__);
return 1;
}
if (blk_sense_request(rq)) {
- /* We got an error trying to get sense info
- from the drive (probably while trying
- to recover from a former error). Just give up. */
-
+ /*
+ * We got an error trying to get sense info from the drive
+ * (probably while trying to recover from a former error).
+ * Just give up.
+ */
rq->cmd_flags |= REQ_FAILED;
cdrom_end_request(drive, 0);
ide_error(drive, "request sense failure", stat);
@@ -332,13 +335,12 @@
if (blk_pc_request(rq) && !rq->errors)
rq->errors = SAM_STAT_CHECK_CONDITION;
- /* Check for tray open. */
+ /* check for tray open */
if (sense_key == NOT_READY) {
cdrom_saw_media_change(drive);
} else if (sense_key == UNIT_ATTENTION) {
- /* Check for media change. */
+ /* check for media change */
cdrom_saw_media_change(drive);
- /*printk("%s: media changed\n",drive->name);*/
return 0;
} else if (sense_key == ILLEGAL_REQUEST &&
rq->cmd[0] == GPCMD_START_STOP_UNIT) {
@@ -350,7 +352,7 @@
* cdrom_log_sense() knows this!
*/
} else if (!(rq->cmd_flags & REQ_QUIET)) {
- /* Otherwise, print an error. */
+ /* otherwise, print an error */
ide_dump_status(drive, "packet command error", stat);
}
@@ -366,27 +368,30 @@
} else if (blk_fs_request(rq)) {
int do_end_request = 0;
- /* Handle errors from READ and WRITE requests. */
+ /* handle errors from READ and WRITE requests */
if (blk_noretry_request(rq))
do_end_request = 1;
if (sense_key == NOT_READY) {
- /* Tray open. */
+ /* tray open */
if (rq_data_dir(rq) == READ) {
cdrom_saw_media_change(drive);
- /* Fail the request. */
- printk("%s: tray open\n", drive->name);
+ /* fail the request */
+ printk(KERN_ERR "%s: tray open\n", drive->name);
do_end_request = 1;
} else {
struct cdrom_info *info = drive->driver_data;
- /* allow the drive 5 seconds to recover, some
+ /*
+ * Allow the drive 5 seconds to recover, some
* devices will return this error while flushing
- * data from cache */
+ * data from cache.
+ */
if (!rq->errors)
- info->write_timeout = jiffies + ATAPI_WAIT_WRITE_BUSY;
+ info->write_timeout = jiffies +
+ ATAPI_WAIT_WRITE_BUSY;
rq->errors = 1;
if (time_after(jiffies, info->write_timeout))
do_end_request = 1;
@@ -394,65 +399,68 @@
unsigned long flags;
/*
- * take a breather relying on the
- * unplug timer to kick us again
+ * take a breather relying on the unplug
+ * timer to kick us again
*/
spin_lock_irqsave(&ide_lock, flags);
blk_plug_device(drive->queue);
- spin_unlock_irqrestore(&ide_lock, flags);
+ spin_unlock_irqrestore(&ide_lock,
+ flags);
return 1;
}
}
} else if (sense_key == UNIT_ATTENTION) {
- /* Media change. */
- cdrom_saw_media_change (drive);
+ /* media change */
+ cdrom_saw_media_change(drive);
/*
- * Arrange to retry the request.
- * But be sure to give up if we've retried
- * too many times.
+ * Arrange to retry the request but be sure to give up
+ * if we've retried too many times.
*/
if (++rq->errors > ERROR_MAX)
do_end_request = 1;
} else if (sense_key == ILLEGAL_REQUEST ||
sense_key == DATA_PROTECT) {
/*
- * No point in retrying after an illegal
- * request or data protect error.
+ * No point in retrying after an illegal request or data
+ * protect error.
*/
ide_dump_status_no_sense(drive, "command error", stat);
do_end_request = 1;
} else if (sense_key == MEDIUM_ERROR) {
/*
* No point in re-trying a zillion times on a bad
- * sector... If we got here the error is not correctable
+ * sector. If we got here the error is not correctable.
*/
- ide_dump_status_no_sense(drive, "media error (bad sector)", stat);
+ ide_dump_status_no_sense(drive,
+ "media error (bad sector)",
+ stat);
do_end_request = 1;
} else if (sense_key == BLANK_CHECK) {
- /* Disk appears blank ?? */
- ide_dump_status_no_sense(drive, "media error (blank)", stat);
+ /* disk appears blank ?? */
+ ide_dump_status_no_sense(drive, "media error (blank)",
+ stat);
do_end_request = 1;
} else if ((err & ~ABRT_ERR) != 0) {
- /* Go to the default handler
- for other errors. */
+ /* go to the default handler for other errors */
ide_error(drive, "cdrom_decode_status", stat);
return 1;
} else if ((++rq->errors > ERROR_MAX)) {
- /* We've racked up too many retries. Abort. */
+ /* we've racked up too many retries, abort */
do_end_request = 1;
}
- /* End a request through request sense analysis when we have
- sense data. We need this in order to perform end of media
- processing */
-
+ /*
+ * End a request through request sense analysis when we have
+ * sense data. We need this in order to perform end of media
+ * processing.
+ */
if (do_end_request)
goto end_request;
/*
- * If we got a CHECK_CONDITION status,
- * queue a request sense command.
+ * If we got a CHECK_CONDITION status, queue
+ * a request sense command.
*/
if (stat & ERR_STAT)
cdrom_queue_request_sense(drive, NULL, NULL);
@@ -461,7 +469,7 @@
cdrom_end_request(drive, 0);
}
- /* Retry, or handle the next request. */
+ /* retry, or handle the next request */
return 1;
end_request:
@@ -486,10 +494,10 @@
unsigned long wait = 0;
/*
- * Some commands are *slow* and normally take a long time to
- * complete. Usually we can use the ATAPI "disconnect" to bypass
- * this, but not all commands/drives support that. Let
- * ide_timer_expiry keep polling us for these.
+ * Some commands are *slow* and normally take a long time to complete.
+ * Usually we can use the ATAPI "disconnect" to bypass this, but not all
+ * commands/drives support that. Let ide_timer_expiry keep polling us
+ * for these.
*/
switch (rq->cmd[0]) {
case GPCMD_BLANK:
@@ -501,20 +509,22 @@
break;
default:
if (!(rq->cmd_flags & REQ_QUIET))
- printk(KERN_INFO "ide-cd: cmd 0x%x timed out\n", rq->cmd[0]);
+ printk(KERN_INFO "ide-cd: cmd 0x%x timed out\n",
+ rq->cmd[0]);
wait = 0;
break;
}
return wait;
}
-/* Set up the device registers for transferring a packet command on DEV,
- expecting to later transfer XFERLEN bytes. HANDLER is the routine
- which actually transfers the command to the drive. If this is a
- drq_interrupt device, this routine will arrange for HANDLER to be
- called when the interrupt from the drive arrives. Otherwise, HANDLER
- will be called immediately after the drive is prepared for the transfer. */
-
+/*
+ * Set up the device registers for transferring a packet command on DEV,
+ * expecting to later transfer XFERLEN bytes. HANDLER is the routine
+ * which actually transfers the command to the drive. If this is a
+ * drq_interrupt device, this routine will arrange for HANDLER to be
+ * called when the interrupt from the drive arrives. Otherwise, HANDLER
+ * will be called immediately after the drive is prepared for the transfer.
+ */
static ide_startstop_t cdrom_start_packet_command(ide_drive_t *drive,
int xferlen,
ide_handler_t *handler)
@@ -523,15 +533,15 @@
struct cdrom_info *info = drive->driver_data;
ide_hwif_t *hwif = drive->hwif;
- /* Wait for the controller to be idle. */
+ /* wait for the controller to be idle */
if (ide_wait_stat(&startstop, drive, 0, BUSY_STAT, WAIT_READY))
return startstop;
/* FIXME: for Virtual DMA we must check harder */
if (info->dma)
- info->dma = !hwif->dma_setup(drive);
+ info->dma = !hwif->dma_ops->dma_setup(drive);
- /* Set up the controller registers. */
+ /* set up the controller registers */
ide_pktcmd_tf_load(drive, IDE_TFLAG_OUT_NSECT | IDE_TFLAG_OUT_LBAL |
IDE_TFLAG_NO_SELECT_MASK, xferlen, info->dma);
@@ -541,7 +551,8 @@
drive->waiting_for_dma = 0;
/* packet command */
- ide_execute_command(drive, WIN_PACKETCMD, handler, ATAPI_WAIT_PC, cdrom_timer_expiry);
+ ide_execute_command(drive, WIN_PACKETCMD, handler,
+ ATAPI_WAIT_PC, cdrom_timer_expiry);
return ide_started;
} else {
unsigned long flags;
@@ -557,11 +568,12 @@
}
}
-/* Send a packet command to DRIVE described by CMD_BUF and CMD_LEN.
- The device registers must have already been prepared
- by cdrom_start_packet_command.
- HANDLER is the interrupt handler to call when the command completes
- or there's data ready. */
+/*
+ * Send a packet command to DRIVE described by CMD_BUF and CMD_LEN. The device
+ * registers must have already been prepared by cdrom_start_packet_command.
+ * HANDLER is the interrupt handler to call when the command completes or
+ * there's data ready.
+ */
#define ATAPI_MIN_CDB_BYTES 12
static ide_startstop_t cdrom_transfer_packet_command(ide_drive_t *drive,
struct request *rq,
@@ -573,24 +585,26 @@
ide_startstop_t startstop;
if (info->cd_flags & IDE_CD_FLAG_DRQ_INTERRUPT) {
- /* Here we should have been called after receiving an interrupt
- from the device. DRQ should how be set. */
+ /*
+ * Here we should have been called after receiving an interrupt
+ * from the device. DRQ should how be set.
+ */
- /* Check for errors. */
+ /* check for errors */
if (cdrom_decode_status(drive, DRQ_STAT, NULL))
return ide_stopped;
- /* Ok, next interrupt will be DMA interrupt. */
+ /* ok, next interrupt will be DMA interrupt */
if (info->dma)
drive->waiting_for_dma = 1;
} else {
- /* Otherwise, we must wait for DRQ to get set. */
+ /* otherwise, we must wait for DRQ to get set */
if (ide_wait_stat(&startstop, drive, DRQ_STAT,
BUSY_STAT, WAIT_READY))
return startstop;
}
- /* Arm the interrupt handler. */
+ /* arm the interrupt handler */
ide_set_handler(drive, handler, rq->timeout, cdrom_timer_expiry);
/* ATAPI commands get padded out to 12 bytes minimum */
@@ -598,20 +612,19 @@
if (cmd_len < ATAPI_MIN_CDB_BYTES)
cmd_len = ATAPI_MIN_CDB_BYTES;
- /* Send the command to the device. */
+ /* send the command to the device */
HWIF(drive)->atapi_output_bytes(drive, rq->cmd, cmd_len);
- /* Start the DMA if need be */
+ /* start the DMA if need be */
if (info->dma)
- hwif->dma_start(drive);
+ hwif->dma_ops->dma_start(drive);
return ide_started;
}
-/****************************************************************************
+/*
* Block read functions.
*/
-
static void ide_cd_pad_transfer(ide_drive_t *drive, xfer_func_t *xf, int len)
{
while (len > 0) {
@@ -649,20 +662,21 @@
ide_hwif_t *hwif = drive->hwif;
xfer_func_t *xf;
- /* Whoops... */
+ /* whoops... */
printk(KERN_ERR "%s: %s: wrong transfer direction!\n",
drive->name, __func__);
xf = rw ? hwif->atapi_output_bytes : hwif->atapi_input_bytes;
ide_cd_pad_transfer(drive, xf, len);
} else if (rw == 0 && ireason == 1) {
- /* Some drives (ASUS) seem to tell us that status
- * info is available. just get it and ignore.
+ /*
+ * Some drives (ASUS) seem to tell us that status info is
+ * available. Just get it and ignore.
*/
(void)ide_read_status(drive);
return 0;
} else {
- /* Drive wants a command packet, or invalid ireason... */
+ /* drive wants a command packet, or invalid ireason... */
printk(KERN_ERR "%s: %s: bad interrupt reason 0x%02x\n",
drive->name, __func__, ireason);
}
@@ -702,10 +716,10 @@
static ide_startstop_t cdrom_newpc_intr(ide_drive_t *);
/*
- * Routine to send a read/write packet command to the drive.
- * This is usually called directly from cdrom_start_{read,write}().
- * However, for drq_interrupt devices, it is called from an interrupt
- * when the drive is ready to accept the command.
+ * Routine to send a read/write packet command to the drive. This is usually
+ * called directly from cdrom_start_{read,write}(). However, for drq_interrupt
+ * devices, it is called from an interrupt when the drive is ready to accept
+ * the command.
*/
static ide_startstop_t cdrom_start_rw_cont(ide_drive_t *drive)
{
@@ -727,7 +741,7 @@
* is larger than the buffer size.
*/
if (nskip > 0) {
- /* Sanity check... */
+ /* sanity check... */
if (rq->current_nr_sectors !=
bio_cur_sectors(rq->bio)) {
printk(KERN_ERR "%s: %s: buffer botch (%u)\n",
@@ -744,10 +758,10 @@
/* the immediate bit */
rq->cmd[1] = 1 << 3;
#endif
- /* Set up the command */
+ /* set up the command */
rq->timeout = ATAPI_WAIT_PC;
- /* Send the command to the drive and return. */
+ /* send the command to the drive and return */
return cdrom_transfer_packet_command(drive, rq, cdrom_newpc_intr);
}
@@ -767,14 +781,8 @@
info->cd_flags |= IDE_CD_FLAG_SEEKING;
if (retry && time_after(jiffies, info->start_seek + IDECD_SEEK_TIMER)) {
- if (--retry == 0) {
- /*
- * this condition is far too common, to bother
- * users about it
- */
- /* printk("%s: disabled DSC seek overlap\n", drive->name);*/
+ if (--retry == 0)
drive->dsc_overlap = 0;
- }
}
return ide_stopped;
}
@@ -800,32 +808,34 @@
info->dma = 0;
info->start_seek = jiffies;
- return cdrom_start_packet_command(drive, 0, cdrom_start_seek_continuation);
+ return cdrom_start_packet_command(drive, 0,
+ cdrom_start_seek_continuation);
}
/*
- * Fix up a possibly partially-processed request so that we can
- * start it over entirely, or even put it back on the request queue.
+ * Fix up a possibly partially-processed request so that we can start it over
+ * entirely, or even put it back on the request queue.
*/
static void restore_request(struct request *rq)
{
if (rq->buffer != bio_data(rq->bio)) {
- sector_t n = (rq->buffer - (char *) bio_data(rq->bio)) / SECTOR_SIZE;
+ sector_t n =
+ (rq->buffer - (char *)bio_data(rq->bio)) / SECTOR_SIZE;
rq->buffer = bio_data(rq->bio);
rq->nr_sectors += n;
rq->sector -= n;
}
- rq->hard_cur_sectors = rq->current_nr_sectors = bio_cur_sectors(rq->bio);
+ rq->current_nr_sectors = bio_cur_sectors(rq->bio);
+ rq->hard_cur_sectors = rq->current_nr_sectors;
rq->hard_nr_sectors = rq->nr_sectors;
rq->hard_sector = rq->sector;
rq->q->prep_rq_fn(rq->q, rq);
}
-/****************************************************************************
- * Execute all other packet commands.
+/*
+ * All other packet commands.
*/
-
static void ide_cd_request_sense_fixup(struct request *rq)
{
/*
@@ -849,7 +859,7 @@
if (rq->sense == NULL)
rq->sense = &sense;
- /* Start of retry loop. */
+ /* start of retry loop */
do {
int error;
unsigned long time = jiffies;
@@ -858,41 +868,45 @@
error = ide_do_drive_cmd(drive, rq, ide_wait);
time = jiffies - time;
- /* FIXME: we should probably abort/retry or something
- * in case of failure */
+ /*
+ * FIXME: we should probably abort/retry or something in case of
+ * failure.
+ */
if (rq->cmd_flags & REQ_FAILED) {
- /* The request failed. Retry if it was due to a unit
- attention status
- (usually means media was changed). */
+ /*
+ * The request failed. Retry if it was due to a unit
+ * attention status (usually means media was changed).
+ */
struct request_sense *reqbuf = rq->sense;
if (reqbuf->sense_key == UNIT_ATTENTION)
cdrom_saw_media_change(drive);
else if (reqbuf->sense_key == NOT_READY &&
reqbuf->asc == 4 && reqbuf->ascq != 4) {
- /* The drive is in the process of loading
- a disk. Retry, but wait a little to give
- the drive time to complete the load. */
+ /*
+ * The drive is in the process of loading
+ * a disk. Retry, but wait a little to give
+ * the drive time to complete the load.
+ */
ssleep(2);
} else {
- /* Otherwise, don't retry. */
+ /* otherwise, don't retry */
retries = 0;
}
--retries;
}
- /* End of retry loop. */
+ /* end of retry loop */
} while ((rq->cmd_flags & REQ_FAILED) && retries >= 0);
- /* Return an error if the command failed. */
+ /* return an error if the command failed */
return (rq->cmd_flags & REQ_FAILED) ? -EIO : 0;
}
/*
- * Called from blk_end_request_callback() after the data of the request
- * is completed and before the request is completed.
- * By returning value '1', blk_end_request_callback() returns immediately
- * without completing the request.
+ * Called from blk_end_request_callback() after the data of the request is
+ * completed and before the request itself is completed. By returning value '1',
+ * blk_end_request_callback() returns immediately without completing it.
*/
static int cdrom_newpc_intr_dummy_cb(struct request *rq)
{
@@ -911,11 +925,11 @@
unsigned int timeout;
u8 lowcyl, highcyl;
- /* Check for errors. */
+ /* check for errors */
dma = info->dma;
if (dma) {
info->dma = 0;
- dma_error = HWIF(drive)->ide_dma_end(drive);
+ dma_error = hwif->dma_ops->dma_end(drive);
if (dma_error) {
printk(KERN_ERR "%s: DMA %s error\n", drive->name,
write ? "write" : "read");
@@ -926,9 +940,7 @@
if (cdrom_decode_status(drive, 0, &stat))
return ide_stopped;
- /*
- * using dma, transfer is complete now
- */
+ /* using dma, transfer is complete now */
if (dma) {
if (dma_error)
return ide_error(drive, "dma error", stat);
@@ -939,9 +951,7 @@
goto end_request;
}
- /*
- * ok we fall to pio :/
- */
+ /* ok we fall to pio :/ */
ireason = hwif->INB(hwif->io_ports[IDE_IREASON_OFFSET]) & 0x3;
lowcyl = hwif->INB(hwif->io_ports[IDE_BCOUNTL_OFFSET]);
highcyl = hwif->INB(hwif->io_ports[IDE_BCOUNTH_OFFSET]);
@@ -952,9 +962,7 @@
if (thislen > len)
thislen = len;
- /*
- * If DRQ is clear, the command has completed.
- */
+ /* If DRQ is clear, the command has completed. */
if ((stat & DRQ_STAT) == 0) {
if (blk_fs_request(rq)) {
/*
@@ -975,15 +983,13 @@
return ide_stopped;
} else if (!blk_pc_request(rq)) {
ide_cd_request_sense_fixup(rq);
- /* Complain if we still have data left to transfer. */
+ /* complain if we still have data left to transfer */
uptodate = rq->data_len ? 0 : 1;
}
goto end_request;
}
- /*
- * check which way to transfer data
- */
+ /* check which way to transfer data */
if (ide_cd_check_ireason(drive, rq, len, ireason, write))
return ide_stopped;
@@ -1019,16 +1025,12 @@
xferfunc = HWIF(drive)->atapi_input_bytes;
}
- /*
- * transfer data
- */
+ /* transfer data */
while (thislen > 0) {
u8 *ptr = blk_fs_request(rq) ? NULL : rq->data;
int blen = rq->data_len;
- /*
- * bio backed?
- */
+ /* bio backed? */
if (rq->bio) {
if (blk_fs_request(rq)) {
ptr = rq->buffer;
@@ -1043,7 +1045,8 @@
if (blk_fs_request(rq) && !write)
/*
* If the buffers are full, pipe the rest into
- * oblivion. */
+ * oblivion.
+ */
ide_cd_drain_data(drive, thislen >> 9);
else {
printk(KERN_ERR "%s: confused, missing data\n",
@@ -1090,9 +1093,7 @@
rq->sense_len += blen;
}
- /*
- * pad, if necessary
- */
+ /* pad, if necessary */
if (!blk_fs_request(rq) && len > 0)
ide_cd_pad_transfer(drive, xferfunc, len);
@@ -1136,9 +1137,7 @@
queue_hardsect_size(drive->queue) >> SECTOR_BITS;
if (write) {
- /*
- * disk has become write protected
- */
+ /* disk has become write protected */
if (cd->disk->policy) {
cdrom_end_request(drive, 0);
return ide_stopped;
@@ -1151,9 +1150,7 @@
restore_request(rq);
}
- /*
- * use DMA, if possible / writes *must* be hardware frame aligned
- */
+ /* use DMA, if possible / writes *must* be hardware frame aligned */
if ((rq->nr_sectors & (sectors_per_frame - 1)) ||
(rq->sector & (sectors_per_frame - 1))) {
if (write) {
@@ -1167,7 +1164,7 @@
if (write)
cd->devinfo.media_written = 1;
- /* Start sending the read/write request to the drive. */
+ /* start sending the read/write request to the drive */
return cdrom_start_packet_command(drive, 32768, cdrom_start_rw_cont);
}
@@ -1192,12 +1189,11 @@
info->dma = 0;
- /*
- * sg request
- */
+ /* sg request */
if (rq->bio) {
int mask = drive->queue->dma_alignment;
- unsigned long addr = (unsigned long) page_address(bio_page(rq->bio));
+ unsigned long addr =
+ (unsigned long)page_address(bio_page(rq->bio));
info->dma = drive->using_dma;
@@ -1211,15 +1207,16 @@
info->dma = 0;
}
- /* Start sending the command to the drive. */
- return cdrom_start_packet_command(drive, rq->data_len, cdrom_do_newpc_cont);
+ /* start sending the command to the drive */
+ return cdrom_start_packet_command(drive, rq->data_len,
+ cdrom_do_newpc_cont);
}
-/****************************************************************************
+/*
* cdrom driver request routine.
*/
-static ide_startstop_t
-ide_do_rw_cdrom(ide_drive_t *drive, struct request *rq, sector_t block)
+static ide_startstop_t ide_do_rw_cdrom(ide_drive_t *drive, struct request *rq,
+ sector_t block)
{
ide_startstop_t action;
struct cdrom_info *info = drive->driver_data;
@@ -1231,14 +1228,19 @@
if ((stat & SEEK_STAT) != SEEK_STAT) {
if (elapsed < IDECD_SEEK_TIMEOUT) {
- ide_stall_queue(drive, IDECD_SEEK_TIMER);
+ ide_stall_queue(drive,
+ IDECD_SEEK_TIMER);
return ide_stopped;
}
- printk(KERN_ERR "%s: DSC timeout\n", drive->name);
+ printk(KERN_ERR "%s: DSC timeout\n",
+ drive->name);
}
info->cd_flags &= ~IDE_CD_FLAG_SEEKING;
}
- if ((rq_data_dir(rq) == READ) && IDE_LARGE_SEEK(info->last_block, block, IDECD_SEEK_THRESHOLD) && drive->dsc_overlap)
+ if (rq_data_dir(rq) == READ &&
+ IDE_LARGE_SEEK(info->last_block, block,
+ IDECD_SEEK_THRESHOLD) &&
+ drive->dsc_overlap)
action = cdrom_start_seek(drive, block);
else
action = cdrom_start_rw(drive, rq);
@@ -1248,9 +1250,7 @@
rq->cmd_type == REQ_TYPE_ATA_PC) {
return cdrom_do_block_pc(drive, rq);
} else if (blk_special_request(rq)) {
- /*
- * right now this can only be a reset...
- */
+ /* right now this can only be a reset... */
cdrom_end_request(drive, 1);
return ide_stopped;
}
@@ -1262,18 +1262,16 @@
-/****************************************************************************
+/*
* Ioctl handling.
*
- * Routines which queue packet commands take as a final argument a pointer
- * to a request_sense struct. If execution of the command results
- * in an error with a CHECK CONDITION status, this structure will be filled
- * with the results of the subsequent request sense command. The pointer
- * can also be NULL, in which case no sense information is returned.
+ * Routines which queue packet commands take as a final argument a pointer to a
+ * request_sense struct. If execution of the command results in an error with a
+ * CHECK CONDITION status, this structure will be filled with the results of the
+ * subsequent request sense command. The pointer can also be NULL, in which case
+ * no sense information is returned.
*/
-
-static
-void msf_from_bcd(struct atapi_msf *msf)
+static void msf_from_bcd(struct atapi_msf *msf)
{
msf->minute = BCD2BIN(msf->minute);
msf->second = BCD2BIN(msf->second);
@@ -1293,8 +1291,8 @@
req.cmd_flags |= REQ_QUIET;
/*
- * Sanyo 3 CD changer uses byte 7 of TEST_UNIT_READY to
- * switch CDs instead of supporting the LOAD_UNLOAD opcode.
+ * Sanyo 3 CD changer uses byte 7 of TEST_UNIT_READY to switch CDs
+ * instead of supporting the LOAD_UNLOAD opcode.
*/
req.cmd[7] = cdi->sanyo_slot % 3;
@@ -1370,36 +1368,39 @@
unsigned long sectors_per_frame = SECTORS_PER_FRAME;
if (toc == NULL) {
- /* Try to allocate space. */
+ /* try to allocate space */
toc = kmalloc(sizeof(struct atapi_toc), GFP_KERNEL);
if (toc == NULL) {
- printk(KERN_ERR "%s: No cdrom TOC buffer!\n", drive->name);
+ printk(KERN_ERR "%s: No cdrom TOC buffer!\n",
+ drive->name);
return -ENOMEM;
}
info->toc = toc;
}
- /* Check to see if the existing data is still valid.
- If it is, just return. */
+ /*
+ * Check to see if the existing data is still valid. If it is,
+ * just return.
+ */
(void) cdrom_check_status(drive, sense);
if (info->cd_flags & IDE_CD_FLAG_TOC_VALID)
return 0;
- /* Try to get the total cdrom capacity and sector size. */
+ /* try to get the total cdrom capacity and sector size */
stat = cdrom_read_capacity(drive, &toc->capacity, §ors_per_frame,
sense);
if (stat)
toc->capacity = 0x1fffff;
set_capacity(info->disk, toc->capacity * sectors_per_frame);
- /* Save a private copy of te TOC capacity for error handling */
+ /* save a private copy of the TOC capacity for error handling */
drive->probed_capacity = toc->capacity * sectors_per_frame;
blk_queue_hardsect_size(drive->queue,
sectors_per_frame << SECTOR_BITS);
- /* First read just the header, so we know how long the TOC is. */
+ /* first read just the header, so we know how long the TOC is */
stat = cdrom_read_tocentry(drive, 0, 1, 0, (char *) &toc->hdr,
sizeof(struct atapi_toc_header), sense);
if (stat)
@@ -1416,7 +1417,7 @@
if (ntracks > MAX_TRACKS)
ntracks = MAX_TRACKS;
- /* Now read the whole schmeer. */
+ /* now read the whole schmeer */
stat = cdrom_read_tocentry(drive, toc->hdr.first_track, 1, 0,
(char *)&toc->hdr,
sizeof(struct atapi_toc_header) +
@@ -1424,15 +1425,18 @@
sizeof(struct atapi_toc_entry), sense);
if (stat && toc->hdr.first_track > 1) {
- /* Cds with CDI tracks only don't have any TOC entries,
- despite of this the returned values are
- first_track == last_track = number of CDI tracks + 1,
- so that this case is indistinguishable from the same
- layout plus an additional audio track.
- If we get an error for the regular case, we assume
- a CDI without additional audio tracks. In this case
- the readable TOC is empty (CDI tracks are not included)
- and only holds the Leadout entry. Heiko Eißfeldt */
+ /*
+ * Cds with CDI tracks only don't have any TOC entries, despite
+ * of this the returned values are
+ * first_track == last_track = number of CDI tracks + 1,
+ * so that this case is indistinguishable from the same layout
+ * plus an additional audio track. If we get an error for the
+ * regular case, we assume a CDI without additional audio
+ * tracks. In this case the readable TOC is empty (CDI tracks
+ * are not included) and only holds the Leadout entry.
+ *
+ * Heiko Eißfeldt.
+ */
ntracks = 0;
stat = cdrom_read_tocentry(drive, CDROM_LEADOUT, 1, 0,
(char *)&toc->hdr,
@@ -1473,9 +1477,8 @@
toc->ent[i].addr.msf.frame);
}
- /* Read the multisession information. */
if (toc->hdr.first_track != CDROM_LEADOUT) {
- /* Read the multisession information. */
+ /* read the multisession information */
stat = cdrom_read_tocentry(drive, 0, 0, 1, (char *)&ms_tmp,
sizeof(ms_tmp), sense);
if (stat)
@@ -1483,12 +1486,13 @@
toc->last_session_lba = be32_to_cpu(ms_tmp.ent.addr.lba);
} else {
- ms_tmp.hdr.first_track = ms_tmp.hdr.last_track = CDROM_LEADOUT;
+ ms_tmp.hdr.last_track = CDROM_LEADOUT;
+ ms_tmp.hdr.first_track = ms_tmp.hdr.last_track;
toc->last_session_lba = msf_to_lba(0, 2, 0); /* 0m 2s 0f */
}
if (info->cd_flags & IDE_CD_FLAG_TOCADDR_AS_BCD) {
- /* Re-read multisession information using MSF format */
+ /* re-read multisession information using MSF format */
stat = cdrom_read_tocentry(drive, 0, 1, 1, (char *)&ms_tmp,
sizeof(ms_tmp), sense);
if (stat)
@@ -1502,7 +1506,7 @@
toc->xa_flag = (ms_tmp.hdr.first_track != ms_tmp.hdr.last_track);
- /* Now try to get the total cdrom capacity. */
+ /* now try to get the total cdrom capacity */
stat = cdrom_get_last_written(cdi, &last_written);
if (!stat && (last_written > toc->capacity)) {
toc->capacity = last_written;
@@ -1527,7 +1531,8 @@
size -= ATAPI_CAPABILITIES_PAGE_PAD_SIZE;
init_cdrom_command(&cgc, buf, size, CGC_DATA_UNKNOWN);
- do { /* we seem to get stat=0x01,err=0x00 the first time (??) */
+ do {
+ /* we seem to get stat=0x01,err=0x00 the first time (??) */
stat = cdrom_mode_sense(cdi, &cgc, GPMODE_CAPABILITIES_PAGE, 0);
if (!stat)
break;
@@ -1596,8 +1601,7 @@
return register_cdrom(devinfo);
}
-static
-int ide_cdrom_probe_capabilities(ide_drive_t *drive)
+static int ide_cdrom_probe_capabilities(ide_drive_t *drive)
{
struct cdrom_info *cd = drive->driver_data;
struct cdrom_device_info *cdi = &cd->devinfo;
@@ -1611,7 +1615,8 @@
if (drive->media == ide_optical) {
cdi->mask &= ~(CDC_MO_DRIVE | CDC_RAM);
- printk(KERN_ERR "%s: ATAPI magneto-optical drive\n", drive->name);
+ printk(KERN_ERR "%s: ATAPI magneto-optical drive\n",
+ drive->name);
return nslots;
}
@@ -1622,11 +1627,10 @@
}
/*
- * we have to cheat a little here. the packet will eventually
- * be queued with ide_cdrom_packet(), which extracts the
- * drive from cdi->handle. Since this device hasn't been
- * registered with the Uniform layer yet, it can't do this.
- * Same goes for cdi->ops.
+ * We have to cheat a little here. the packet will eventually be queued
+ * with ide_cdrom_packet(), which extracts the drive from cdi->handle.
+ * Since this device hasn't been registered with the Uniform layer yet,
+ * it can't do this. Same goes for cdi->ops.
*/
cdi->handle = drive;
cdi->ops = &ide_cdrom_dops;
@@ -1695,18 +1699,7 @@
return nslots;
}
-#ifdef CONFIG_IDE_PROC_FS
-static void ide_cdrom_add_settings(ide_drive_t *drive)
-{
- ide_add_setting(drive, "dsc_overlap", SETTING_RW, TYPE_BYTE, 0, 1, 1, 1, &drive->dsc_overlap, NULL);
-}
-#else
-static inline void ide_cdrom_add_settings(ide_drive_t *drive) { ; }
-#endif
-
-/*
- * standard prep_rq_fn that builds 10 byte cmds
- */
+/* standard prep_rq_fn that builds 10 byte cmds */
static int ide_cdrom_prep_fs(struct request_queue *q, struct request *rq)
{
int hard_sect = queue_hardsect_size(q);
@@ -1745,9 +1738,7 @@
{
u8 *c = rq->cmd;
- /*
- * Transform 6-byte read/write commands to the 10-byte version
- */
+ /* transform 6-byte read/write commands to the 10-byte version */
if (c[0] == READ_6 || c[0] == WRITE_6) {
c[8] = c[4];
c[5] = c[3];
@@ -1789,6 +1780,41 @@
unsigned int cd_flags;
};
+#ifdef CONFIG_IDE_PROC_FS
+static sector_t ide_cdrom_capacity(ide_drive_t *drive)
+{
+ unsigned long capacity, sectors_per_frame;
+
+ if (cdrom_read_capacity(drive, &capacity, §ors_per_frame, NULL))
+ return 0;
+
+ return capacity * sectors_per_frame;
+}
+
+static int proc_idecd_read_capacity(char *page, char **start, off_t off,
+ int count, int *eof, void *data)
+{
+ ide_drive_t *drive = data;
+ int len;
+
+ len = sprintf(page, "%llu\n", (long long)ide_cdrom_capacity(drive));
+ PROC_IDE_READ_RETURN(page, start, off, count, eof, len);
+}
+
+static ide_proc_entry_t idecd_proc[] = {
+ { "capacity", S_IFREG|S_IRUGO, proc_idecd_read_capacity, NULL },
+ { NULL, 0, NULL, NULL }
+};
+
+static void ide_cdrom_add_settings(ide_drive_t *drive)
+{
+ ide_add_setting(drive, "dsc_overlap", SETTING_RW, TYPE_BYTE, 0, 1, 1, 1,
+ &drive->dsc_overlap, NULL);
+}
+#else
+static inline void ide_cdrom_add_settings(ide_drive_t *drive) { ; }
+#endif
+
static const struct cd_list_entry ide_cd_quirks_list[] = {
/* Limit transfer size per interrupt. */
{ "SAMSUNG CD-ROM SCR-2430", NULL, IDE_CD_FLAG_LIMIT_NFRAMES },
@@ -1846,8 +1872,7 @@
return 0;
}
-static
-int ide_cdrom_setup(ide_drive_t *drive)
+static int ide_cdrom_setup(ide_drive_t *drive)
{
struct cdrom_info *cd = drive->driver_data;
struct cdrom_device_info *cdi = &cd->devinfo;
@@ -1876,13 +1901,12 @@
id->fw_rev[4] == '1' && id->fw_rev[6] <= '2')
cd->cd_flags |= IDE_CD_FLAG_TOCTRACKS_AS_BCD;
else if (cd->cd_flags & IDE_CD_FLAG_SANYO_3CD)
- cdi->sanyo_slot = 3; /* 3 => use CD in slot 0 */
+ /* 3 => use CD in slot 0 */
+ cdi->sanyo_slot = 3;
nslots = ide_cdrom_probe_capabilities(drive);
- /*
- * set correct block size
- */
+ /* set correct block size */
blk_queue_hardsect_size(drive->queue, CD_FRAMESIZE);
if (drive->autotune == IDE_TUNE_DEFAULT ||
@@ -1890,7 +1914,8 @@
drive->dsc_overlap = (drive->next != drive);
if (ide_cdrom_register(drive, nslots)) {
- printk(KERN_ERR "%s: ide_cdrom_setup failed to register device with the cdrom driver.\n", drive->name);
+ printk(KERN_ERR "%s: %s failed to register device with the"
+ " cdrom driver.\n", drive->name, __func__);
cd->devinfo.handle = NULL;
return 1;
}
@@ -1929,33 +1954,6 @@
static int ide_cd_probe(ide_drive_t *);
-#ifdef CONFIG_IDE_PROC_FS
-static sector_t ide_cdrom_capacity(ide_drive_t *drive)
-{
- unsigned long capacity, sectors_per_frame;
-
- if (cdrom_read_capacity(drive, &capacity, §ors_per_frame, NULL))
- return 0;
-
- return capacity * sectors_per_frame;
-}
-
-static int proc_idecd_read_capacity
- (char *page, char **start, off_t off, int count, int *eof, void *data)
-{
- ide_drive_t *drive = data;
- int len;
-
- len = sprintf(page, "%llu\n", (long long)ide_cdrom_capacity(drive));
- PROC_IDE_READ_RETURN(page, start, off, count, eof, len);
-}
-
-static ide_proc_entry_t idecd_proc[] = {
- { "capacity", S_IFREG|S_IRUGO, proc_idecd_read_capacity, NULL },
- { NULL, 0, NULL, NULL }
-};
-#endif
-
static ide_driver_t ide_cdrom_driver = {
.gen_driver = {
.owner = THIS_MODULE,
@@ -2093,7 +2091,7 @@
.revalidate_disk = idecd_revalidate_disk
};
-/* options */
+/* module options */
static char *ignore;
module_param(ignore, charp, 0400);
@@ -2114,17 +2112,20 @@
/* skip drives that we were told to ignore */
if (ignore != NULL) {
if (strstr(ignore, drive->name)) {
- printk(KERN_INFO "ide-cd: ignoring drive %s\n", drive->name);
+ printk(KERN_INFO "ide-cd: ignoring drive %s\n",
+ drive->name);
goto failed;
}
}
if (drive->scsi) {
- printk(KERN_INFO "ide-cd: passing drive %s to ide-scsi emulation.\n", drive->name);
+ printk(KERN_INFO "ide-cd: passing drive %s to ide-scsi "
+ "emulation.\n", drive->name);
goto failed;
}
info = kzalloc(sizeof(struct cdrom_info), GFP_KERNEL);
if (info == NULL) {
- printk(KERN_ERR "%s: Can't allocate a cdrom structure\n", drive->name);
+ printk(KERN_ERR "%s: Can't allocate a cdrom structure\n",
+ drive->name);
goto failed;
}
diff --git a/drivers/ide/ide-dma.c b/drivers/ide/ide-dma.c
index 8757e5e..c352cf2 100644
--- a/drivers/ide/ide-dma.c
+++ b/drivers/ide/ide-dma.c
@@ -102,7 +102,7 @@
{
u8 stat = 0, dma_stat = 0;
- dma_stat = HWIF(drive)->ide_dma_end(drive);
+ dma_stat = drive->hwif->dma_ops->dma_end(drive);
stat = ide_read_status(drive);
if (OK_STAT(stat,DRIVE_READY,drive->bad_wstat|DRQ_STAT)) {
@@ -394,7 +394,7 @@
drive->using_dma = 0;
ide_toggle_bounce(drive, 0);
- drive->hwif->dma_host_set(drive, 0);
+ drive->hwif->dma_ops->dma_host_set(drive, 0);
}
EXPORT_SYMBOL(ide_dma_off_quietly);
@@ -427,7 +427,7 @@
drive->using_dma = 1;
ide_toggle_bounce(drive, 1);
- drive->hwif->dma_host_set(drive, 1);
+ drive->hwif->dma_ops->dma_host_set(drive, 1);
}
#ifdef CONFIG_BLK_DEV_IDEDMA_SFF
@@ -482,11 +482,12 @@
EXPORT_SYMBOL_GPL(ide_dma_setup);
-static void ide_dma_exec_cmd(ide_drive_t *drive, u8 command)
+void ide_dma_exec_cmd(ide_drive_t *drive, u8 command)
{
/* issue cmd to drive */
ide_execute_command(drive, command, &ide_dma_intr, 2*WAIT_CMD, dma_timer_expiry);
}
+EXPORT_SYMBOL_GPL(ide_dma_exec_cmd);
void ide_dma_start(ide_drive_t *drive)
{
@@ -532,7 +533,7 @@
EXPORT_SYMBOL(__ide_dma_end);
/* returns 1 if dma irq issued, 0 otherwise */
-static int __ide_dma_test_irq(ide_drive_t *drive)
+int ide_dma_test_irq(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
u8 dma_stat = hwif->INB(hwif->dma_status);
@@ -542,9 +543,10 @@
return 1;
if (!drive->waiting_for_dma)
printk(KERN_WARNING "%s: (%s) called while not waiting\n",
- drive->name, __FUNCTION__);
+ drive->name, __func__);
return 0;
}
+EXPORT_SYMBOL_GPL(ide_dma_test_irq);
#else
static inline int config_drive_for_dma(ide_drive_t *drive) { return 0; }
#endif /* CONFIG_BLK_DEV_IDEDMA_SFF */
@@ -574,6 +576,7 @@
{
struct hd_driveid *id = drive->id;
ide_hwif_t *hwif = drive->hwif;
+ const struct ide_port_ops *port_ops = hwif->port_ops;
unsigned int mask = 0;
switch(base) {
@@ -581,8 +584,8 @@
if ((id->field_valid & 4) == 0)
break;
- if (hwif->udma_filter)
- mask = hwif->udma_filter(drive);
+ if (port_ops && port_ops->udma_filter)
+ mask = port_ops->udma_filter(drive);
else
mask = hwif->ultra_mask;
mask &= id->dma_ultra;
@@ -598,8 +601,8 @@
case XFER_MW_DMA_0:
if ((id->field_valid & 2) == 0)
break;
- if (hwif->mdma_filter)
- mask = hwif->mdma_filter(drive);
+ if (port_ops && port_ops->mdma_filter)
+ mask = port_ops->mdma_filter(drive);
else
mask = hwif->mwdma_mask;
mask &= id->dma_mword;
@@ -801,15 +804,15 @@
printk(KERN_ERR "%s: timeout waiting for DMA\n", drive->name);
- if (hwif->ide_dma_test_irq(drive))
+ if (hwif->dma_ops->dma_test_irq(drive))
return;
- hwif->ide_dma_end(drive);
+ hwif->dma_ops->dma_end(drive);
}
EXPORT_SYMBOL(ide_dma_timeout);
-static void ide_release_dma_engine(ide_hwif_t *hwif)
+void ide_release_dma_engine(ide_hwif_t *hwif)
{
if (hwif->dmatable_cpu) {
struct pci_dev *pdev = to_pci_dev(hwif->dev);
@@ -820,28 +823,7 @@
}
}
-static int ide_release_iomio_dma(ide_hwif_t *hwif)
-{
- release_region(hwif->dma_base, 8);
- if (hwif->extra_ports)
- release_region(hwif->extra_base, hwif->extra_ports);
- return 1;
-}
-
-/*
- * Needed for allowing full modular support of ide-driver
- */
-int ide_release_dma(ide_hwif_t *hwif)
-{
- ide_release_dma_engine(hwif);
-
- if (hwif->mmio)
- return 1;
- else
- return ide_release_iomio_dma(hwif);
-}
-
-static int ide_allocate_dma_engine(ide_hwif_t *hwif)
+int ide_allocate_dma_engine(ide_hwif_t *hwif)
{
struct pci_dev *pdev = to_pci_dev(hwif->dev);
@@ -853,65 +835,25 @@
return 0;
printk(KERN_ERR "%s: -- Error, unable to allocate DMA table.\n",
- hwif->cds->name);
+ hwif->name);
return 1;
}
+EXPORT_SYMBOL_GPL(ide_allocate_dma_engine);
-static int ide_mapped_mmio_dma(ide_hwif_t *hwif, unsigned long base)
-{
- printk(KERN_INFO " %s: MMIO-DMA ", hwif->name);
-
- return 0;
-}
-
-static int ide_iomio_dma(ide_hwif_t *hwif, unsigned long base)
-{
- printk(KERN_INFO " %s: BM-DMA at 0x%04lx-0x%04lx",
- hwif->name, base, base + 7);
-
- if (!request_region(base, 8, hwif->name)) {
- printk(" -- Error, ports in use.\n");
- return 1;
- }
-
- if (hwif->cds->extra) {
- hwif->extra_base = base + (hwif->channel ? 8 : 16);
-
- if (!hwif->mate || !hwif->mate->extra_ports) {
- if (!request_region(hwif->extra_base,
- hwif->cds->extra, hwif->cds->name)) {
- printk(" -- Error, extra ports in use.\n");
- release_region(base, 8);
- return 1;
- }
- hwif->extra_ports = hwif->cds->extra;
- }
- }
-
- return 0;
-}
-
-static int ide_dma_iobase(ide_hwif_t *hwif, unsigned long base)
-{
- if (hwif->mmio)
- return ide_mapped_mmio_dma(hwif, base);
-
- return ide_iomio_dma(hwif, base);
-}
+static const struct ide_dma_ops sff_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ide_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = ide_dma_start,
+ .dma_end = __ide_dma_end,
+ .dma_test_irq = ide_dma_test_irq,
+ .dma_timeout = ide_dma_timeout,
+ .dma_lost_irq = ide_dma_lost_irq,
+};
void ide_setup_dma(ide_hwif_t *hwif, unsigned long base)
{
- u8 dma_stat;
-
- if (ide_dma_iobase(hwif, base))
- return;
-
- if (ide_allocate_dma_engine(hwif)) {
- ide_release_dma(hwif);
- return;
- }
-
hwif->dma_base = base;
if (!hwif->dma_command)
@@ -925,27 +867,7 @@
if (!hwif->dma_prdtable)
hwif->dma_prdtable = hwif->dma_base + 4;
- if (!hwif->dma_host_set)
- hwif->dma_host_set = &ide_dma_host_set;
- if (!hwif->dma_setup)
- hwif->dma_setup = &ide_dma_setup;
- if (!hwif->dma_exec_cmd)
- hwif->dma_exec_cmd = &ide_dma_exec_cmd;
- if (!hwif->dma_start)
- hwif->dma_start = &ide_dma_start;
- if (!hwif->ide_dma_end)
- hwif->ide_dma_end = &__ide_dma_end;
- if (!hwif->ide_dma_test_irq)
- hwif->ide_dma_test_irq = &__ide_dma_test_irq;
- if (!hwif->dma_timeout)
- hwif->dma_timeout = &ide_dma_timeout;
- if (!hwif->dma_lost_irq)
- hwif->dma_lost_irq = &ide_dma_lost_irq;
-
- dma_stat = hwif->INB(hwif->dma_status);
- printk(KERN_CONT ", BIOS settings: %s:%s, %s:%s\n",
- hwif->drives[0].name, (dma_stat & 0x20) ? "DMA" : "PIO",
- hwif->drives[1].name, (dma_stat & 0x40) ? "DMA" : "PIO");
+ hwif->dma_ops = &sff_dma_ops;
}
EXPORT_SYMBOL_GPL(ide_setup_dma);
diff --git a/drivers/ide/ide-floppy.c b/drivers/ide/ide-floppy.c
index ed19a8b..6e891bc 100644
--- a/drivers/ide/ide-floppy.c
+++ b/drivers/ide/ide-floppy.c
@@ -411,7 +411,7 @@
debug_log("Reached %s interrupt handler\n", __func__);
if (pc->flags & PC_FLAG_DMA_IN_PROGRESS) {
- dma_error = hwif->ide_dma_end(drive);
+ dma_error = hwif->dma_ops->dma_end(drive);
if (dma_error) {
printk(KERN_ERR "%s: DMA %s error\n", drive->name,
rq_data_dir(rq) ? "write" : "read");
@@ -663,7 +663,7 @@
dma = 0;
if ((pc->flags & PC_FLAG_DMA_RECOMMENDED) && drive->using_dma)
- dma = !hwif->dma_setup(drive);
+ dma = !hwif->dma_ops->dma_setup(drive);
ide_pktcmd_tf_load(drive, IDE_TFLAG_NO_SELECT_MASK |
IDE_TFLAG_OUT_DEVICE, bcount, dma);
@@ -671,7 +671,7 @@
if (dma) {
/* Begin DMA, if necessary */
pc->flags |= PC_FLAG_DMA_IN_PROGRESS;
- hwif->dma_start(drive);
+ hwif->dma_ops->dma_start(drive);
}
/* Can we transfer the packet when we get the interrupt or wait? */
diff --git a/drivers/ide/ide-generic.c b/drivers/ide/ide-generic.c
index 19f63e3..a6073e2 100644
--- a/drivers/ide/ide-generic.c
+++ b/drivers/ide/ide-generic.c
@@ -94,7 +94,24 @@
unsigned long io_addr = ide_default_io_base(i);
hw_regs_t hw;
+ idx[i] = 0xff;
+
if (io_addr) {
+ if (!request_region(io_addr, 8, DRV_NAME)) {
+ printk(KERN_ERR "%s: I/O resource 0x%lX-0x%lX "
+ "not free.\n",
+ DRV_NAME, io_addr, io_addr + 7);
+ continue;
+ }
+
+ if (!request_region(io_addr + 0x206, 1, DRV_NAME)) {
+ printk(KERN_ERR "%s: I/O resource 0x%lX "
+ "not free.\n",
+ DRV_NAME, io_addr + 0x206);
+ release_region(io_addr, 8);
+ continue;
+ }
+
/*
* Skip probing if the corresponding
* slot is already occupied.
@@ -111,8 +128,7 @@
ide_init_port_hw(hwif, &hw);
idx[i] = i;
- } else
- idx[i] = 0xff;
+ }
}
ide_device_add_all(idx, NULL);
diff --git a/drivers/ide/ide-io.c b/drivers/ide/ide-io.c
index 51d181e..0fe89a5 100644
--- a/drivers/ide/ide-io.c
+++ b/drivers/ide/ide-io.c
@@ -218,7 +218,7 @@
* we could be smarter and check for current xfer_speed
* in struct drive etc...
*/
- if (drive->hwif->dma_host_set == NULL)
+ if (drive->hwif->dma_ops == NULL)
break;
/*
* TODO: respect ->using_dma setting
@@ -721,6 +721,7 @@
#endif
if (s->b.set_tune) {
ide_hwif_t *hwif = drive->hwif;
+ const struct ide_port_ops *port_ops = hwif->port_ops;
u8 req_pio = drive->tune_req;
s->b.set_tune = 0;
@@ -733,10 +734,10 @@
unsigned long flags;
spin_lock_irqsave(&ide_lock, flags);
- hwif->set_pio_mode(drive, req_pio);
+ port_ops->set_pio_mode(drive, req_pio);
spin_unlock_irqrestore(&ide_lock, flags);
} else
- hwif->set_pio_mode(drive, req_pio);
+ port_ops->set_pio_mode(drive, req_pio);
} else {
int keep_dma = drive->using_dma;
@@ -1237,12 +1238,12 @@
if (error < 0) {
printk(KERN_WARNING "%s: DMA timeout error\n", drive->name);
- (void)HWIF(drive)->ide_dma_end(drive);
+ (void)hwif->dma_ops->dma_end(drive);
ret = ide_error(drive, "dma timeout error",
ide_read_status(drive));
} else {
printk(KERN_WARNING "%s: DMA timeout retry\n", drive->name);
- hwif->dma_timeout(drive);
+ hwif->dma_ops->dma_timeout(drive);
}
/*
@@ -1354,7 +1355,7 @@
startstop = handler(drive);
} else if (drive_is_ready(drive)) {
if (drive->waiting_for_dma)
- hwgroup->hwif->dma_lost_irq(drive);
+ hwif->dma_ops->dma_lost_irq(drive);
(void)ide_ack_intr(hwif);
printk(KERN_WARNING "%s: lost interrupt\n", drive->name);
startstop = handler(drive);
diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c
index 4594421..9c646bd 100644
--- a/drivers/ide/ide-iops.c
+++ b/drivers/ide/ide-iops.c
@@ -159,17 +159,20 @@
void SELECT_DRIVE (ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
+ const struct ide_port_ops *port_ops = hwif->port_ops;
- if (hwif->selectproc)
- hwif->selectproc(drive);
+ if (port_ops && port_ops->selectproc)
+ port_ops->selectproc(drive);
hwif->OUTB(drive->select.all, hwif->io_ports[IDE_SELECT_OFFSET]);
}
void SELECT_MASK (ide_drive_t *drive, int mask)
{
- if (HWIF(drive)->maskproc)
- HWIF(drive)->maskproc(drive, mask);
+ const struct ide_port_ops *port_ops = drive->hwif->port_ops;
+
+ if (port_ops && port_ops->maskproc)
+ port_ops->maskproc(drive, mask);
}
/*
@@ -429,7 +432,7 @@
u8 stat = 0;
if (drive->waiting_for_dma)
- return hwif->ide_dma_test_irq(drive);
+ return hwif->dma_ops->dma_test_irq(drive);
#if 0
/* need to guarantee 400ns since last command was issued */
@@ -700,8 +703,8 @@
// msleep(50);
#ifdef CONFIG_BLK_DEV_IDEDMA
- if (hwif->dma_host_set) /* check if host supports DMA */
- hwif->dma_host_set(drive, 0);
+ if (hwif->dma_ops) /* check if host supports DMA */
+ hwif->dma_ops->dma_host_set(drive, 0);
#endif
/* Skip setting PIO flow-control modes on pre-EIDE drives */
@@ -759,8 +762,8 @@
#ifdef CONFIG_BLK_DEV_IDEDMA
if ((speed >= XFER_SW_DMA_0 || (hwif->host_flags & IDE_HFLAG_VDMA)) &&
drive->using_dma)
- hwif->dma_host_set(drive, 1);
- else if (hwif->dma_host_set) /* check if host supports DMA */
+ hwif->dma_ops->dma_host_set(drive, 1);
+ else if (hwif->dma_ops) /* check if host supports DMA */
ide_dma_off_quietly(drive);
#endif
@@ -905,10 +908,11 @@
{
ide_hwgroup_t *hwgroup = HWGROUP(drive);
ide_hwif_t *hwif = HWIF(drive);
+ const struct ide_port_ops *port_ops = hwif->port_ops;
u8 tmp;
- if (hwif->reset_poll != NULL) {
- if (hwif->reset_poll(drive)) {
+ if (port_ops && port_ops->reset_poll) {
+ if (port_ops->reset_poll(drive)) {
printk(KERN_ERR "%s: host reset_poll failure for %s.\n",
hwif->name, drive->name);
return ide_stopped;
@@ -974,6 +978,8 @@
static void pre_reset(ide_drive_t *drive)
{
+ const struct ide_port_ops *port_ops = drive->hwif->port_ops;
+
if (drive->media == ide_disk)
ide_disk_pre_reset(drive);
else
@@ -994,8 +1000,8 @@
return;
}
- if (HWIF(drive)->pre_reset != NULL)
- HWIF(drive)->pre_reset(drive);
+ if (port_ops && port_ops->pre_reset)
+ port_ops->pre_reset(drive);
if (drive->current_speed != 0xff)
drive->desired_speed = drive->current_speed;
@@ -1023,6 +1029,7 @@
unsigned long flags;
ide_hwif_t *hwif;
ide_hwgroup_t *hwgroup;
+ const struct ide_port_ops *port_ops;
u8 ctl;
spin_lock_irqsave(&ide_lock, flags);
@@ -1089,8 +1096,9 @@
* state when the disks are reset this way. At least, the Winbond
* 553 documentation says that
*/
- if (hwif->resetproc)
- hwif->resetproc(drive);
+ port_ops = hwif->port_ops;
+ if (port_ops && port_ops->resetproc)
+ port_ops->resetproc(drive);
spin_unlock_irqrestore(&ide_lock, flags);
return ide_started;
diff --git a/drivers/ide/ide-lib.c b/drivers/ide/ide-lib.c
index c859de7..6f04ea3 100644
--- a/drivers/ide/ide-lib.c
+++ b/drivers/ide/ide-lib.c
@@ -85,7 +85,7 @@
mode = XFER_PIO_4;
}
-// printk("%s: mode 0x%02x, speed 0x%02x\n", __FUNCTION__, mode, speed);
+/* printk("%s: mode 0x%02x, speed 0x%02x\n", __func__, mode, speed); */
return min(speed, mode);
}
@@ -288,9 +288,10 @@
void ide_set_pio(ide_drive_t *drive, u8 req_pio)
{
ide_hwif_t *hwif = drive->hwif;
+ const struct ide_port_ops *port_ops = hwif->port_ops;
u8 host_pio, pio;
- if (hwif->set_pio_mode == NULL ||
+ if (port_ops == NULL || port_ops->set_pio_mode == NULL ||
(hwif->host_flags & IDE_HFLAG_NO_SET_MODE))
return;
@@ -343,29 +344,30 @@
int ide_set_pio_mode(ide_drive_t *drive, const u8 mode)
{
ide_hwif_t *hwif = drive->hwif;
+ const struct ide_port_ops *port_ops = hwif->port_ops;
if (hwif->host_flags & IDE_HFLAG_NO_SET_MODE)
return 0;
- if (hwif->set_pio_mode == NULL)
+ if (port_ops == NULL || port_ops->set_pio_mode == NULL)
return -1;
/*
* TODO: temporary hack for some legacy host drivers that didn't
* set transfer mode on the device in ->set_pio_mode method...
*/
- if (hwif->set_dma_mode == NULL) {
- hwif->set_pio_mode(drive, mode - XFER_PIO_0);
+ if (port_ops->set_dma_mode == NULL) {
+ port_ops->set_pio_mode(drive, mode - XFER_PIO_0);
return 0;
}
if (hwif->host_flags & IDE_HFLAG_POST_SET_MODE) {
if (ide_config_drive_speed(drive, mode))
return -1;
- hwif->set_pio_mode(drive, mode - XFER_PIO_0);
+ port_ops->set_pio_mode(drive, mode - XFER_PIO_0);
return 0;
} else {
- hwif->set_pio_mode(drive, mode - XFER_PIO_0);
+ port_ops->set_pio_mode(drive, mode - XFER_PIO_0);
return ide_config_drive_speed(drive, mode);
}
}
@@ -373,20 +375,21 @@
int ide_set_dma_mode(ide_drive_t *drive, const u8 mode)
{
ide_hwif_t *hwif = drive->hwif;
+ const struct ide_port_ops *port_ops = hwif->port_ops;
if (hwif->host_flags & IDE_HFLAG_NO_SET_MODE)
return 0;
- if (hwif->set_dma_mode == NULL)
+ if (port_ops == NULL || port_ops->set_dma_mode == NULL)
return -1;
if (hwif->host_flags & IDE_HFLAG_POST_SET_MODE) {
if (ide_config_drive_speed(drive, mode))
return -1;
- hwif->set_dma_mode(drive, mode);
+ port_ops->set_dma_mode(drive, mode);
return 0;
} else {
- hwif->set_dma_mode(drive, mode);
+ port_ops->set_dma_mode(drive, mode);
return ide_config_drive_speed(drive, mode);
}
}
@@ -406,8 +409,9 @@
int ide_set_xfer_rate(ide_drive_t *drive, u8 rate)
{
ide_hwif_t *hwif = drive->hwif;
+ const struct ide_port_ops *port_ops = hwif->port_ops;
- if (hwif->set_dma_mode == NULL ||
+ if (port_ops == NULL || port_ops->set_dma_mode == NULL ||
(hwif->host_flags & IDE_HFLAG_NO_SET_MODE))
return -1;
diff --git a/drivers/ide/ide-pnp.c b/drivers/ide/ide-pnp.c
index 8a178a5..10c20e9 100644
--- a/drivers/ide/ide-pnp.c
+++ b/drivers/ide/ide-pnp.c
@@ -18,6 +18,8 @@
#include <linux/pnp.h>
#include <linux/ide.h>
+#define DRV_NAME "ide-pnp"
+
/* Add your devices here :)) */
static struct pnp_device_id idepnp_devices[] = {
/* Generic ESDI/IDE/ATA compatible hard disk controller */
@@ -29,13 +31,29 @@
{
hw_regs_t hw;
ide_hwif_t *hwif;
+ unsigned long base, ctl;
if (!(pnp_port_valid(dev, 0) && pnp_port_valid(dev, 1) && pnp_irq_valid(dev, 0)))
return -1;
+ base = pnp_port_start(dev, 0);
+ ctl = pnp_port_start(dev, 1);
+
+ if (!request_region(base, 8, DRV_NAME)) {
+ printk(KERN_ERR "%s: I/O resource 0x%lX-0x%lX not free.\n",
+ DRV_NAME, base, base + 7);
+ return -EBUSY;
+ }
+
+ if (!request_region(ctl, 1, DRV_NAME)) {
+ printk(KERN_ERR "%s: I/O resource 0x%lX not free.\n",
+ DRV_NAME, ctl);
+ release_region(base, 8);
+ return -EBUSY;
+ }
+
memset(&hw, 0, sizeof(hw));
- ide_std_init_ports(&hw, pnp_port_start(dev, 0),
- pnp_port_start(dev, 1));
+ ide_std_init_ports(&hw, base, ctl);
hw.irq = pnp_irq(dev, 0);
hwif = ide_find_port();
@@ -54,6 +72,9 @@
return 0;
}
+ release_region(ctl, 1);
+ release_region(base, 8);
+
return -1;
}
@@ -65,6 +86,9 @@
ide_unregister(hwif->index);
else
printk(KERN_ERR "idepnp: Unable to remove device, please report.\n");
+
+ release_region(pnp_port_start(dev, 1), 1);
+ release_region(pnp_port_start(dev, 0), 8);
}
static struct pnp_driver idepnp_driver = {
diff --git a/drivers/ide/ide-probe.c b/drivers/ide/ide-probe.c
index 8754297..a4b65b3 100644
--- a/drivers/ide/ide-probe.c
+++ b/drivers/ide/ide-probe.c
@@ -644,7 +644,7 @@
ret = device_register(&hwif->gendev);
if (ret < 0) {
printk(KERN_WARNING "IDE: %s: device_register error: %d\n",
- __FUNCTION__, ret);
+ __func__, ret);
goto out;
}
@@ -773,8 +773,7 @@
BUG_ON(hwif->present);
- if (hwif->noprobe ||
- (hwif->drives[0].noprobe && hwif->drives[1].noprobe))
+ if (hwif->drives[0].noprobe && hwif->drives[1].noprobe)
return -EACCES;
/*
@@ -821,13 +820,14 @@
static void ide_port_tune_devices(ide_hwif_t *hwif)
{
+ const struct ide_port_ops *port_ops = hwif->port_ops;
int unit;
for (unit = 0; unit < MAX_DRIVES; unit++) {
ide_drive_t *drive = &hwif->drives[unit];
- if (drive->present && hwif->quirkproc)
- hwif->quirkproc(drive);
+ if (drive->present && port_ops && port_ops->quirkproc)
+ port_ops->quirkproc(drive);
}
for (unit = 0; unit < MAX_DRIVES; ++unit) {
@@ -843,7 +843,7 @@
drive->nice1 = 1;
- if (hwif->dma_host_set)
+ if (hwif->dma_ops)
ide_set_dma(drive);
}
}
@@ -1324,6 +1324,7 @@
static void ide_port_init_devices(ide_hwif_t *hwif)
{
+ const struct ide_port_ops *port_ops = hwif->port_ops;
int i;
for (i = 0; i < MAX_DRIVES; i++) {
@@ -1339,8 +1340,8 @@
drive->autotune = 1;
}
- if (hwif->port_init_devs)
- hwif->port_init_devs(hwif);
+ if (port_ops && port_ops->port_init_devs)
+ port_ops->port_init_devs(hwif);
}
static void ide_init_port(ide_hwif_t *hwif, unsigned int port,
@@ -1355,9 +1356,6 @@
if (d->init_iops)
d->init_iops(hwif);
- if ((d->host_flags & IDE_HFLAG_NO_DMA) == 0)
- ide_hwif_setup_dma(hwif, d);
-
if ((!hwif->irq && (d->host_flags & IDE_HFLAG_LEGACY_IRQS)) ||
(d->host_flags & IDE_HFLAG_FORCE_LEGACY_IRQS))
hwif->irq = port ? 15 : 14;
@@ -1365,16 +1363,36 @@
hwif->host_flags = d->host_flags;
hwif->pio_mask = d->pio_mask;
- if ((d->host_flags & IDE_HFLAG_SERIALIZE) && hwif->mate)
- hwif->mate->serialized = hwif->serialized = 1;
+ /* ->set_pio_mode for DTC2278 is currently limited to port 0 */
+ if (hwif->chipset != ide_dtc2278 || hwif->channel == 0)
+ hwif->port_ops = d->port_ops;
+
+ if ((d->host_flags & IDE_HFLAG_SERIALIZE) ||
+ ((d->host_flags & IDE_HFLAG_SERIALIZE_DMA) && hwif->dma_base)) {
+ if (hwif->mate)
+ hwif->mate->serialized = hwif->serialized = 1;
+ }
hwif->swdma_mask = d->swdma_mask;
hwif->mwdma_mask = d->mwdma_mask;
hwif->ultra_mask = d->udma_mask;
- /* reset DMA masks only for SFF-style DMA controllers */
- if ((d->host_flags & IDE_HFLAG_NO_DMA) == 0 && hwif->dma_base == 0)
- hwif->swdma_mask = hwif->mwdma_mask = hwif->ultra_mask = 0;
+ if ((d->host_flags & IDE_HFLAG_NO_DMA) == 0) {
+ int rc;
+
+ if (d->init_dma)
+ rc = d->init_dma(hwif, d);
+ else
+ rc = ide_hwif_setup_dma(hwif, d);
+
+ if (rc < 0) {
+ printk(KERN_INFO "%s: DMA disabled\n", hwif->name);
+ hwif->swdma_mask = 0;
+ hwif->mwdma_mask = 0;
+ hwif->ultra_mask = 0;
+ } else if (d->dma_ops)
+ hwif->dma_ops = d->dma_ops;
+ }
if (d->host_flags & IDE_HFLAG_RQSIZE_256)
hwif->rqsize = 256;
@@ -1386,9 +1404,11 @@
static void ide_port_cable_detect(ide_hwif_t *hwif)
{
- if (hwif->cable_detect && (hwif->ultra_mask & 0x78)) {
+ const struct ide_port_ops *port_ops = hwif->port_ops;
+
+ if (port_ops && port_ops->cable_detect && (hwif->ultra_mask & 0x78)) {
if (hwif->cbl != ATA_CBL_PATA40_SHORT)
- hwif->cbl = hwif->cable_detect(hwif);
+ hwif->cbl = port_ops->cable_detect(hwif);
}
}
@@ -1523,25 +1543,15 @@
hwif = &ide_hwifs[idx[i]];
- if ((hwif->chipset != ide_4drives || !hwif->mate ||
- !hwif->mate->present) && ide_hwif_request_regions(hwif)) {
- printk(KERN_ERR "%s: ports already in use, "
- "skipping probe\n", hwif->name);
- continue;
- }
-
- if (ide_probe_port(hwif) < 0) {
- ide_hwif_release_regions(hwif);
- continue;
- }
-
- hwif->present = 1;
+ if (ide_probe_port(hwif) == 0)
+ hwif->present = 1;
if (hwif->chipset != ide_4drives || !hwif->mate ||
!hwif->mate->present)
ide_register_port(hwif);
- ide_port_tune_devices(hwif);
+ if (hwif->present)
+ ide_port_tune_devices(hwif);
}
for (i = 0; i < MAX_HWIFS; i++) {
@@ -1550,9 +1560,6 @@
hwif = &ide_hwifs[idx[i]];
- if (!hwif->present)
- continue;
-
if (hwif_init(hwif) == 0) {
printk(KERN_INFO "%s: failed to initialize IDE "
"interface\n", hwif->name);
@@ -1561,10 +1568,13 @@
continue;
}
- ide_port_setup_devices(hwif);
+ if (hwif->present)
+ ide_port_setup_devices(hwif);
ide_acpi_init(hwif);
- ide_acpi_port_init_devices(hwif);
+
+ if (hwif->present)
+ ide_acpi_port_init_devices(hwif);
}
for (i = 0; i < MAX_HWIFS; i++) {
@@ -1573,11 +1583,11 @@
hwif = &ide_hwifs[idx[i]];
- if (hwif->present) {
- if (hwif->chipset == ide_unknown)
- hwif->chipset = ide_generic;
+ if (hwif->chipset == ide_unknown)
+ hwif->chipset = ide_generic;
+
+ if (hwif->present)
hwif_register_devices(hwif);
- }
}
for (i = 0; i < MAX_HWIFS; i++) {
@@ -1586,11 +1596,11 @@
hwif = &ide_hwifs[idx[i]];
- if (hwif->present) {
- ide_sysfs_register_port(hwif);
- ide_proc_register_port(hwif);
+ ide_sysfs_register_port(hwif);
+ ide_proc_register_port(hwif);
+
+ if (hwif->present)
ide_proc_port_register_devices(hwif);
- }
}
return rc;
@@ -1626,3 +1636,67 @@
ide_proc_port_register_devices(hwif);
}
EXPORT_SYMBOL_GPL(ide_port_scan);
+
+static void ide_legacy_init_one(u8 *idx, hw_regs_t *hw, u8 port_no,
+ const struct ide_port_info *d,
+ unsigned long config)
+{
+ ide_hwif_t *hwif;
+ unsigned long base, ctl;
+ int irq;
+
+ if (port_no == 0) {
+ base = 0x1f0;
+ ctl = 0x3f6;
+ irq = 14;
+ } else {
+ base = 0x170;
+ ctl = 0x376;
+ irq = 15;
+ }
+
+ if (!request_region(base, 8, d->name)) {
+ printk(KERN_ERR "%s: I/O resource 0x%lX-0x%lX not free.\n",
+ d->name, base, base + 7);
+ return;
+ }
+
+ if (!request_region(ctl, 1, d->name)) {
+ printk(KERN_ERR "%s: I/O resource 0x%lX not free.\n",
+ d->name, ctl);
+ release_region(base, 8);
+ return;
+ }
+
+ ide_std_init_ports(hw, base, ctl);
+ hw->irq = irq;
+
+ hwif = ide_find_port_slot(d);
+ if (hwif) {
+ ide_init_port_hw(hwif, hw);
+ if (config)
+ hwif->config_data = config;
+ idx[port_no] = hwif->index;
+ }
+}
+
+int ide_legacy_device_add(const struct ide_port_info *d, unsigned long config)
+{
+ u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
+ hw_regs_t hw[2];
+
+ memset(&hw, 0, sizeof(hw));
+
+ if ((d->host_flags & IDE_HFLAG_QD_2ND_PORT) == 0)
+ ide_legacy_init_one(idx, &hw[0], 0, d, config);
+ ide_legacy_init_one(idx, &hw[1], 1, d, config);
+
+ if (idx[0] == 0xff && idx[1] == 0xff &&
+ (d->host_flags & IDE_HFLAG_SINGLE))
+ return -ENOENT;
+
+ ide_device_add(idx, d);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ide_legacy_device_add);
diff --git a/drivers/ide/ide-proc.c b/drivers/ide/ide-proc.c
index 5d3562b..d9d98ac 100644
--- a/drivers/ide/ide-proc.c
+++ b/drivers/ide/ide-proc.c
@@ -599,14 +599,14 @@
err = device_attach(dev);
if (err < 0)
printk(KERN_WARNING "IDE: %s: device_attach error: %d\n",
- __FUNCTION__, err);
+ __func__, err);
drive->driver_req[0] = 0;
if (dev->driver == NULL) {
err = device_attach(dev);
if (err < 0)
printk(KERN_WARNING
"IDE: %s: device_attach(2) error: %d\n",
- __FUNCTION__, err);
+ __func__, err);
}
if (dev->driver && !strcmp(dev->driver->name, driver))
ret = 0;
@@ -820,7 +820,7 @@
err = bus_for_each_drv(&ide_bus_type, NULL, s, proc_print_driver);
if (err < 0)
printk(KERN_WARNING "IDE: %s: bus_for_each_drv error: %d\n",
- __FUNCTION__, err);
+ __func__, err);
return 0;
}
diff --git a/drivers/ide/ide-scan-pci.c b/drivers/ide/ide-scan-pci.c
index 98888da..0e79eff 100644
--- a/drivers/ide/ide-scan-pci.c
+++ b/drivers/ide/ide-scan-pci.c
@@ -102,7 +102,7 @@
if (__pci_register_driver(d, d->driver.owner,
d->driver.mod_name))
printk(KERN_ERR "%s: failed to register %s driver\n",
- __FUNCTION__, d->driver.mod_name);
+ __func__, d->driver.mod_name);
}
return 0;
diff --git a/drivers/ide/ide-tape.c b/drivers/ide/ide-tape.c
index f43fd07..d3d8b8d 100644
--- a/drivers/ide/ide-tape.c
+++ b/drivers/ide/ide-tape.c
@@ -993,7 +993,7 @@
stat = ide_read_status(drive);
if (pc->flags & PC_FLAG_DMA_IN_PROGRESS) {
- if (hwif->ide_dma_end(drive) || (stat & ERR_STAT)) {
+ if (hwif->dma_ops->dma_end(drive) || (stat & ERR_STAT)) {
/*
* A DMA error is sometimes expected. For example,
* if the tape is crossing a filemark during a
@@ -1213,7 +1213,7 @@
#ifdef CONFIG_BLK_DEV_IDEDMA
/* Begin DMA, if necessary */
if (pc->flags & PC_FLAG_DMA_IN_PROGRESS)
- hwif->dma_start(drive);
+ hwif->dma_ops->dma_start(drive);
#endif
/* Send the actual packet */
HWIF(drive)->atapi_output_bytes(drive, pc->c, 12);
@@ -1279,7 +1279,7 @@
ide_dma_off(drive);
}
if ((pc->flags & PC_FLAG_DMA_RECOMMENDED) && drive->using_dma)
- dma_ok = !hwif->dma_setup(drive);
+ dma_ok = !hwif->dma_ops->dma_setup(drive);
ide_pktcmd_tf_load(drive, IDE_TFLAG_NO_SELECT_MASK |
IDE_TFLAG_OUT_DEVICE, bcount, dma_ok);
@@ -1605,14 +1605,6 @@
}
/* Pipeline related functions */
-static inline int idetape_pipeline_active(idetape_tape_t *tape)
-{
- int rc1, rc2;
-
- rc1 = test_bit(IDETAPE_FLAG_PIPELINE_ACTIVE, &tape->flags);
- rc2 = (tape->active_data_rq != NULL);
- return rc1;
-}
/*
* The function below uses __get_free_page to allocate a pipeline stage, along
@@ -2058,7 +2050,7 @@
spin_lock_irqsave(&tape->lock, flags);
tape->next_stage = NULL;
- if (idetape_pipeline_active(tape))
+ if (test_bit(IDETAPE_FLAG_PIPELINE_ACTIVE, &tape->flags))
idetape_wait_for_request(drive, tape->active_data_rq);
spin_unlock_irqrestore(&tape->lock, flags);
@@ -2131,7 +2123,7 @@
debug_log(DBG_SENSE, "%s: cmd=%d\n", __func__, cmd);
- if (idetape_pipeline_active(tape)) {
+ if (test_bit(IDETAPE_FLAG_PIPELINE_ACTIVE, &tape->flags)) {
printk(KERN_ERR "ide-tape: bug: the pipeline is active in %s\n",
__func__);
return (0);
@@ -2162,8 +2154,7 @@
if (tape->next_stage == NULL)
return;
- if (!idetape_pipeline_active(tape)) {
- set_bit(IDETAPE_FLAG_PIPELINE_ACTIVE, &tape->flags);
+ if (!test_and_set_bit(IDETAPE_FLAG_PIPELINE_ACTIVE, &tape->flags)) {
idetape_activate_next_stage(drive);
(void) ide_do_drive_cmd(drive, tape->active_data_rq, ide_end);
}
@@ -2242,13 +2233,14 @@
/* Attempt to allocate a new stage. Beware possible race conditions. */
while ((new_stage = idetape_kmalloc_stage(tape)) == NULL) {
spin_lock_irqsave(&tape->lock, flags);
- if (idetape_pipeline_active(tape)) {
+ if (test_bit(IDETAPE_FLAG_PIPELINE_ACTIVE, &tape->flags)) {
idetape_wait_for_request(drive, tape->active_data_rq);
spin_unlock_irqrestore(&tape->lock, flags);
} else {
spin_unlock_irqrestore(&tape->lock, flags);
idetape_plug_pipeline(drive);
- if (idetape_pipeline_active(tape))
+ if (test_bit(IDETAPE_FLAG_PIPELINE_ACTIVE,
+ &tape->flags))
continue;
/*
* The machine is short on memory. Fallback to non-
@@ -2277,7 +2269,7 @@
* starting to service requests, so that we will be able to keep up with
* the higher speeds of the tape.
*/
- if (!idetape_pipeline_active(tape)) {
+ if (!test_bit(IDETAPE_FLAG_PIPELINE_ACTIVE, &tape->flags)) {
if (tape->nr_stages >= tape->max_stages * 9 / 10 ||
tape->nr_stages >= tape->max_stages -
tape->uncontrolled_pipeline_head_speed * 3 * 1024 /
@@ -2304,10 +2296,11 @@
idetape_tape_t *tape = drive->driver_data;
unsigned long flags;
- while (tape->next_stage || idetape_pipeline_active(tape)) {
+ while (tape->next_stage || test_bit(IDETAPE_FLAG_PIPELINE_ACTIVE,
+ &tape->flags)) {
idetape_plug_pipeline(drive);
spin_lock_irqsave(&tape->lock, flags);
- if (idetape_pipeline_active(tape))
+ if (test_bit(IDETAPE_FLAG_PIPELINE_ACTIVE, &tape->flags))
idetape_wait_for_request(drive, tape->active_data_rq);
spin_unlock_irqrestore(&tape->lock, flags);
}
@@ -2464,7 +2457,7 @@
new_stage = idetape_kmalloc_stage(tape);
}
}
- if (!idetape_pipeline_active(tape)) {
+ if (!test_bit(IDETAPE_FLAG_PIPELINE_ACTIVE, &tape->flags)) {
if (tape->nr_pending_stages >= 3 * max_stages / 4) {
tape->measure_insert_time = 1;
tape->insert_time = jiffies;
diff --git a/drivers/ide/ide-taskfile.c b/drivers/ide/ide-taskfile.c
index 155cc90..a317ca9 100644
--- a/drivers/ide/ide-taskfile.c
+++ b/drivers/ide/ide-taskfile.c
@@ -135,6 +135,7 @@
ide_hwif_t *hwif = HWIF(drive);
struct ide_taskfile *tf = &task->tf;
ide_handler_t *handler = NULL;
+ const struct ide_dma_ops *dma_ops = hwif->dma_ops;
if (task->data_phase == TASKFILE_MULTI_IN ||
task->data_phase == TASKFILE_MULTI_OUT) {
@@ -178,10 +179,10 @@
return ide_started;
default:
if (task_dma_ok(task) == 0 || drive->using_dma == 0 ||
- hwif->dma_setup(drive))
+ dma_ops->dma_setup(drive))
return ide_stopped;
- hwif->dma_exec_cmd(drive, tf->command);
- hwif->dma_start(drive);
+ dma_ops->dma_exec_cmd(drive, tf->command);
+ dma_ops->dma_start(drive);
return ide_started;
}
}
@@ -455,7 +456,7 @@
/* Error? */
if (stat & ERR_STAT)
- return task_error(drive, rq, __FUNCTION__, stat);
+ return task_error(drive, rq, __func__, stat);
/* Didn't want any data? Odd. */
if (!(stat & DRQ_STAT))
@@ -467,7 +468,7 @@
if (!hwif->nleft) {
stat = wait_drive_not_busy(drive);
if (!OK_STAT(stat, 0, BAD_STAT))
- return task_error(drive, rq, __FUNCTION__, stat);
+ return task_error(drive, rq, __func__, stat);
task_end_request(drive, rq, stat);
return ide_stopped;
}
@@ -488,11 +489,11 @@
u8 stat = ide_read_status(drive);
if (!OK_STAT(stat, DRIVE_READY, drive->bad_wstat))
- return task_error(drive, rq, __FUNCTION__, stat);
+ return task_error(drive, rq, __func__, stat);
/* Deal with unexpected ATA data phase. */
if (((stat & DRQ_STAT) == 0) ^ !hwif->nleft)
- return task_error(drive, rq, __FUNCTION__, stat);
+ return task_error(drive, rq, __func__, stat);
if (!hwif->nleft) {
task_end_request(drive, rq, stat);
@@ -675,7 +676,7 @@
/* (hs): give up if multcount is not set */
printk(KERN_ERR "%s: %s Multimode Write " \
"multcount is not set\n",
- drive->name, __FUNCTION__);
+ drive->name, __func__);
err = -EPERM;
goto abort;
}
@@ -692,7 +693,7 @@
/* (hs): give up if multcount is not set */
printk(KERN_ERR "%s: %s Multimode Read failure " \
"multcount is not set\n",
- drive->name, __FUNCTION__);
+ drive->name, __func__);
err = -EPERM;
goto abort;
}
diff --git a/drivers/ide/ide.c b/drivers/ide/ide.c
index d868ca4..bced02f 100644
--- a/drivers/ide/ide.c
+++ b/drivers/ide/ide.c
@@ -227,79 +227,6 @@
return pci_dev_present(pci_default) ? 33 : 50;
}
-static struct resource* hwif_request_region(ide_hwif_t *hwif,
- unsigned long addr, int num)
-{
- struct resource *res = request_region(addr, num, hwif->name);
-
- if (!res)
- printk(KERN_ERR "%s: I/O resource 0x%lX-0x%lX not free.\n",
- hwif->name, addr, addr+num-1);
- return res;
-}
-
-/**
- * ide_hwif_request_regions - request resources for IDE
- * @hwif: interface to use
- *
- * Requests all the needed resources for an interface.
- * Right now core IDE code does this work which is deeply wrong.
- * MMIO leaves it to the controller driver,
- * PIO will migrate this way over time.
- */
-
-int ide_hwif_request_regions(ide_hwif_t *hwif)
-{
- unsigned long addr;
-
- if (hwif->mmio)
- return 0;
-
- addr = hwif->io_ports[IDE_CONTROL_OFFSET];
-
- if (addr && !hwif_request_region(hwif, addr, 1))
- goto control_region_busy;
-
- addr = hwif->io_ports[IDE_DATA_OFFSET];
- BUG_ON((addr | 7) != hwif->io_ports[IDE_STATUS_OFFSET]);
-
- if (!hwif_request_region(hwif, addr, 8))
- goto data_region_busy;
-
- return 0;
-
-data_region_busy:
- addr = hwif->io_ports[IDE_CONTROL_OFFSET];
- if (addr)
- release_region(addr, 1);
-control_region_busy:
- /* If any errors are return, we drop the hwif interface. */
- return -EBUSY;
-}
-
-/**
- * ide_hwif_release_regions - free IDE resources
- *
- * Note that we only release the standard ports,
- * and do not even try to handle any extra ports
- * allocated for weird IDE interface chipsets.
- *
- * Note also that we don't yet handle mmio resources here. More
- * importantly our caller should be doing this so we need to
- * restructure this as a helper function for drivers.
- */
-
-void ide_hwif_release_regions(ide_hwif_t *hwif)
-{
- if (hwif->mmio)
- return;
-
- if (hwif->io_ports[IDE_CONTROL_OFFSET])
- release_region(hwif->io_ports[IDE_CONTROL_OFFSET], 1);
-
- release_region(hwif->io_ports[IDE_DATA_OFFSET], 8);
-}
-
void ide_remove_port_from_hwgroup(ide_hwif_t *hwif)
{
ide_hwgroup_t *hwgroup = hwif->hwgroup;
@@ -436,9 +363,7 @@
spin_lock_irq(&ide_lock);
if (hwif->dma_base)
- (void)ide_release_dma(hwif);
-
- ide_hwif_release_regions(hwif);
+ ide_release_dma_engine(hwif);
/* restore hwif data to pristine status */
ide_init_port_data(hwif, index);
@@ -454,7 +379,6 @@
{
memcpy(hwif->io_ports, hw->io_ports, sizeof(hwif->io_ports));
hwif->irq = hw->irq;
- hwif->noprobe = 0;
hwif->chipset = hw->chipset;
hwif->gendev.parent = hw->dev;
hwif->ack_intr = hw->ack_intr;
@@ -545,7 +469,7 @@
if (!drive->id || !(drive->id->capability & 1))
goto out;
- if (hwif->dma_host_set == NULL)
+ if (hwif->dma_ops == NULL)
goto out;
err = -EBUSY;
@@ -585,11 +509,12 @@
{
struct request rq;
ide_hwif_t *hwif = drive->hwif;
+ const struct ide_port_ops *port_ops = hwif->port_ops;
if (arg < 0 || arg > 255)
return -EINVAL;
- if (hwif->set_pio_mode == NULL ||
+ if (port_ops == NULL || port_ops->set_pio_mode == NULL ||
(hwif->host_flags & IDE_HFLAG_NO_SET_MODE))
return -ENOSYS;
@@ -1005,14 +930,12 @@
goto done;
case -3: /* "nowerr" */
drive->bad_wstat = BAD_R_STAT;
- hwif->noprobe = 0;
goto done;
case -4: /* "cdrom" */
drive->present = 1;
drive->media = ide_cdrom;
/* an ATAPI device ignores DRDY */
drive->ready_stat = 0;
- hwif->noprobe = 0;
goto done;
case -5: /* nodma */
drive->nodma = 1;
@@ -1043,7 +966,6 @@
drive->sect = drive->bios_sect = vals[2];
drive->present = 1;
drive->forced_geom = 1;
- hwif->noprobe = 0;
goto done;
default:
goto bad_option;
diff --git a/drivers/ide/legacy/ali14xx.c b/drivers/ide/legacy/ali14xx.c
index 33bb7b8..6efbf94 100644
--- a/drivers/ide/legacy/ali14xx.c
+++ b/drivers/ide/legacy/ali14xx.c
@@ -49,6 +49,8 @@
#include <asm/io.h>
+#define DRV_NAME "ali14xx"
+
/* port addresses for auto-detection */
#define ALI_NUM_PORTS 4
static const int ports[ALI_NUM_PORTS] __initdata =
@@ -192,18 +194,20 @@
return t;
}
+static const struct ide_port_ops ali14xx_port_ops = {
+ .set_pio_mode = ali14xx_set_pio_mode,
+};
+
static const struct ide_port_info ali14xx_port_info = {
+ .name = DRV_NAME,
.chipset = ide_ali14xx,
+ .port_ops = &ali14xx_port_ops,
.host_flags = IDE_HFLAG_NO_DMA | IDE_HFLAG_NO_AUTOTUNE,
.pio_mask = ATA_PIO4,
};
static int __init ali14xx_probe(void)
{
- ide_hwif_t *hwif, *mate;
- static u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
- hw_regs_t hw[2];
-
printk(KERN_DEBUG "ali14xx: base=0x%03x, regOn=0x%02x.\n",
basePort, regOn);
@@ -213,31 +217,7 @@
return 1;
}
- memset(&hw, 0, sizeof(hw));
-
- ide_std_init_ports(&hw[0], 0x1f0, 0x3f6);
- hw[0].irq = 14;
-
- ide_std_init_ports(&hw[1], 0x170, 0x376);
- hw[1].irq = 15;
-
- hwif = ide_find_port();
- if (hwif) {
- ide_init_port_hw(hwif, &hw[0]);
- hwif->set_pio_mode = &ali14xx_set_pio_mode;
- idx[0] = hwif->index;
- }
-
- mate = ide_find_port();
- if (mate) {
- ide_init_port_hw(mate, &hw[1]);
- mate->set_pio_mode = &ali14xx_set_pio_mode;
- idx[1] = mate->index;
- }
-
- ide_device_add(idx, &ali14xx_port_info);
-
- return 0;
+ return ide_legacy_device_add(&ali14xx_port_info, 0);
}
int probe_ali14xx;
diff --git a/drivers/ide/legacy/buddha.c b/drivers/ide/legacy/buddha.c
index 6956eb8..f51433b 100644
--- a/drivers/ide/legacy/buddha.c
+++ b/drivers/ide/legacy/buddha.c
@@ -228,8 +228,6 @@
ide_init_port_data(hwif, index);
ide_init_port_hw(hwif, &hw);
- hwif->mmio = 1;
-
idx[i] = index;
}
}
diff --git a/drivers/ide/legacy/dtc2278.c b/drivers/ide/legacy/dtc2278.c
index 9c6b324..f7c4ad1 100644
--- a/drivers/ide/legacy/dtc2278.c
+++ b/drivers/ide/legacy/dtc2278.c
@@ -16,6 +16,8 @@
#include <asm/io.h>
+#define DRV_NAME "dtc2278"
+
/*
* Changing this #undef to #define may solve start up problems in some systems.
*/
@@ -86,8 +88,14 @@
}
}
+static const struct ide_port_ops dtc2278_port_ops = {
+ .set_pio_mode = dtc2278_set_pio_mode,
+};
+
static const struct ide_port_info dtc2278_port_info __initdata = {
+ .name = DRV_NAME,
.chipset = ide_dtc2278,
+ .port_ops = &dtc2278_port_ops,
.host_flags = IDE_HFLAG_SERIALIZE |
IDE_HFLAG_NO_UNMASK_IRQS |
IDE_HFLAG_IO_32BIT |
@@ -101,9 +109,6 @@
static int __init dtc2278_probe(void)
{
unsigned long flags;
- ide_hwif_t *hwif, *mate;
- static u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
- hw_regs_t hw[2];
local_irq_save(flags);
/*
@@ -123,30 +128,7 @@
#endif
local_irq_restore(flags);
- memset(&hw, 0, sizeof(hw));
-
- ide_std_init_ports(&hw[0], 0x1f0, 0x3f6);
- hw[0].irq = 14;
-
- ide_std_init_ports(&hw[1], 0x170, 0x376);
- hw[1].irq = 15;
-
- hwif = ide_find_port();
- if (hwif) {
- ide_init_port_hw(hwif, &hw[0]);
- hwif->set_pio_mode = dtc2278_set_pio_mode;
- idx[0] = hwif->index;
- }
-
- mate = ide_find_port();
- if (mate) {
- ide_init_port_hw(mate, &hw[1]);
- idx[1] = mate->index;
- }
-
- ide_device_add(idx, &dtc2278_port_info);
-
- return 0;
+ return ide_legacy_device_add(&dtc2278_port_info, 0);
}
int probe_dtc2278 = 0;
diff --git a/drivers/ide/legacy/falconide.c b/drivers/ide/legacy/falconide.c
index 8c9c9f7..5c19c42 100644
--- a/drivers/ide/legacy/falconide.c
+++ b/drivers/ide/legacy/falconide.c
@@ -89,7 +89,6 @@
ide_init_port_data(hwif, index);
ide_init_port_hw(hwif, &hw);
- hwif->mmio = 1;
ide_get_lock(NULL, NULL);
ide_device_add(idx, NULL);
diff --git a/drivers/ide/legacy/gayle.c b/drivers/ide/legacy/gayle.c
index fcc8d52..a0c9601 100644
--- a/drivers/ide/legacy/gayle.c
+++ b/drivers/ide/legacy/gayle.c
@@ -182,8 +182,6 @@
ide_init_port_data(hwif, index);
ide_init_port_hw(hwif, &hw);
- hwif->mmio = 1;
-
idx[i] = index;
} else
release_mem_region(res_start, res_n);
diff --git a/drivers/ide/legacy/ht6560b.c b/drivers/ide/legacy/ht6560b.c
index 60f52f5..702d8de 100644
--- a/drivers/ide/legacy/ht6560b.c
+++ b/drivers/ide/legacy/ht6560b.c
@@ -328,8 +328,16 @@
module_param_named(probe, probe_ht6560b, bool, 0);
MODULE_PARM_DESC(probe, "probe for HT6560B chipset");
+static const struct ide_port_ops ht6560b_port_ops = {
+ .port_init_devs = ht6560b_port_init_devs,
+ .set_pio_mode = ht6560b_set_pio_mode,
+ .selectproc = ht6560b_selectproc,
+};
+
static const struct ide_port_info ht6560b_port_info __initdata = {
+ .name = DRV_NAME,
.chipset = ide_ht6560b,
+ .port_ops = &ht6560b_port_ops,
.host_flags = IDE_HFLAG_SERIALIZE | /* is this needed? */
IDE_HFLAG_NO_DMA |
IDE_HFLAG_NO_AUTOTUNE |
@@ -339,53 +347,21 @@
static int __init ht6560b_init(void)
{
- ide_hwif_t *hwif, *mate;
- static u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
- hw_regs_t hw[2];
-
if (probe_ht6560b == 0)
return -ENODEV;
if (!request_region(HT_CONFIG_PORT, 1, DRV_NAME)) {
printk(KERN_NOTICE "%s: HT_CONFIG_PORT not found\n",
- __FUNCTION__);
+ __func__);
return -ENODEV;
}
if (!try_to_init_ht6560b()) {
- printk(KERN_NOTICE "%s: HBA not found\n", __FUNCTION__);
+ printk(KERN_NOTICE "%s: HBA not found\n", __func__);
goto release_region;
}
- memset(&hw, 0, sizeof(hw));
-
- ide_std_init_ports(&hw[0], 0x1f0, 0x3f6);
- hw[0].irq = 14;
-
- ide_std_init_ports(&hw[1], 0x170, 0x376);
- hw[1].irq = 15;
-
- hwif = ide_find_port();
- if (hwif) {
- ide_init_port_hw(hwif, &hw[0]);
- hwif->selectproc = ht6560b_selectproc;
- hwif->set_pio_mode = ht6560b_set_pio_mode;
- hwif->port_init_devs = ht6560b_port_init_devs;
- idx[0] = hwif->index;
- }
-
- mate = ide_find_port();
- if (mate) {
- ide_init_port_hw(mate, &hw[1]);
- mate->selectproc = ht6560b_selectproc;
- mate->set_pio_mode = ht6560b_set_pio_mode;
- mate->port_init_devs = ht6560b_port_init_devs;
- idx[1] = mate->index;
- }
-
- ide_device_add(idx, &ht6560b_port_info);
-
- return 0;
+ return ide_legacy_device_add(&ht6560b_port_info, 0);
release_region:
release_region(HT_CONFIG_PORT, 1);
diff --git a/drivers/ide/legacy/ide-4drives.c b/drivers/ide/legacy/ide-4drives.c
index c352f12..17f94d0 100644
--- a/drivers/ide/legacy/ide-4drives.c
+++ b/drivers/ide/legacy/ide-4drives.c
@@ -4,6 +4,8 @@
#include <linux/module.h>
#include <linux/ide.h>
+#define DRV_NAME "ide-4drives"
+
int probe_4drives;
module_param_named(probe, probe_4drives, bool, 0);
@@ -12,15 +14,29 @@
static int __init ide_4drives_init(void)
{
ide_hwif_t *hwif, *mate;
+ unsigned long base = 0x1f0, ctl = 0x3f6;
u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
hw_regs_t hw;
if (probe_4drives == 0)
return -ENODEV;
+ if (!request_region(base, 8, DRV_NAME)) {
+ printk(KERN_ERR "%s: I/O resource 0x%lX-0x%lX not free.\n",
+ DRV_NAME, base, base + 7);
+ return -EBUSY;
+ }
+
+ if (!request_region(ctl, 1, DRV_NAME)) {
+ printk(KERN_ERR "%s: I/O resource 0x%lX not free.\n",
+ DRV_NAME, ctl);
+ release_region(base, 8);
+ return -EBUSY;
+ }
+
memset(&hw, 0, sizeof(hw));
- ide_std_init_ports(&hw, 0x1f0, 0x3f6);
+ ide_std_init_ports(&hw, base, ctl);
hw.irq = 14;
hw.chipset = ide_4drives;
diff --git a/drivers/ide/legacy/ide-cs.c b/drivers/ide/legacy/ide-cs.c
index b97b8d51..855e157 100644
--- a/drivers/ide/legacy/ide-cs.c
+++ b/drivers/ide/legacy/ide-cs.c
@@ -51,6 +51,8 @@
#include <pcmcia/cisreg.h>
#include <pcmcia/ciscode.h>
+#define DRV_NAME "ide-cs"
+
/*====================================================================*/
/* Module parameters */
@@ -72,16 +74,11 @@
/*====================================================================*/
-static const char ide_major[] = {
- IDE0_MAJOR, IDE1_MAJOR, IDE2_MAJOR, IDE3_MAJOR,
- IDE4_MAJOR, IDE5_MAJOR
-};
-
typedef struct ide_info_t {
struct pcmcia_device *p_dev;
+ ide_hwif_t *hwif;
int ndev;
dev_node_t node;
- int hd;
} ide_info_t;
static void ide_release(struct pcmcia_device *);
@@ -136,20 +133,44 @@
static void ide_detach(struct pcmcia_device *link)
{
+ ide_info_t *info = link->priv;
+ ide_hwif_t *hwif = info->hwif;
+
DEBUG(0, "ide_detach(0x%p)\n", link);
ide_release(link);
- kfree(link->priv);
+ release_region(hwif->io_ports[IDE_CONTROL_OFFSET], 1);
+ release_region(hwif->io_ports[IDE_DATA_OFFSET], 8);
+
+ kfree(info);
} /* ide_detach */
-static int idecs_register(unsigned long io, unsigned long ctl, unsigned long irq, struct pcmcia_device *handle)
+static const struct ide_port_ops idecs_port_ops = {
+ .quirkproc = ide_undecoded_slave,
+};
+
+static ide_hwif_t *idecs_register(unsigned long io, unsigned long ctl,
+ unsigned long irq, struct pcmcia_device *handle)
{
ide_hwif_t *hwif;
hw_regs_t hw;
int i;
u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
+ if (!request_region(io, 8, DRV_NAME)) {
+ printk(KERN_ERR "%s: I/O resource 0x%lX-0x%lX not free.\n",
+ DRV_NAME, io, io + 7);
+ return NULL;
+ }
+
+ if (!request_region(ctl, 1, DRV_NAME)) {
+ printk(KERN_ERR "%s: I/O resource 0x%lX not free.\n",
+ DRV_NAME, ctl);
+ release_region(io, 8);
+ return NULL;
+ }
+
memset(&hw, 0, sizeof(hw));
ide_std_init_ports(&hw, io, ctl);
hw.irq = irq;
@@ -158,7 +179,7 @@
hwif = ide_find_port();
if (hwif == NULL)
- return -1;
+ goto out_release;
i = hwif->index;
@@ -168,13 +189,19 @@
ide_init_port_data(hwif, i);
ide_init_port_hw(hwif, &hw);
- hwif->quirkproc = &ide_undecoded_slave;
+ hwif->port_ops = &idecs_port_ops;
idx[0] = i;
ide_device_add(idx, NULL);
- return hwif->present ? i : -1;
+ if (hwif->present)
+ return hwif;
+
+out_release:
+ release_region(ctl, 1);
+ release_region(io, 8);
+ return NULL;
}
/*======================================================================
@@ -199,8 +226,9 @@
cistpl_cftable_entry_t dflt;
} *stk = NULL;
cistpl_cftable_entry_t *cfg;
- int i, pass, last_ret = 0, last_fn = 0, hd, is_kme = 0;
+ int i, pass, last_ret = 0, last_fn = 0, is_kme = 0;
unsigned long io_base, ctl_base;
+ ide_hwif_t *hwif;
DEBUG(0, "ide_config(0x%p)\n", link);
@@ -296,14 +324,15 @@
outb(0x81, ctl_base+1);
/* retry registration in case device is still spinning up */
- for (hd = -1, i = 0; i < 10; i++) {
- hd = idecs_register(io_base, ctl_base, link->irq.AssignedIRQ, link);
- if (hd >= 0) break;
+ for (i = 0; i < 10; i++) {
+ hwif = idecs_register(io_base, ctl_base, link->irq.AssignedIRQ, link);
+ if (hwif)
+ break;
if (link->io.NumPorts1 == 0x20) {
outb(0x02, ctl_base + 0x10);
- hd = idecs_register(io_base + 0x10, ctl_base + 0x10,
- link->irq.AssignedIRQ, link);
- if (hd >= 0) {
+ hwif = idecs_register(io_base + 0x10, ctl_base + 0x10,
+ link->irq.AssignedIRQ, link);
+ if (hwif) {
io_base += 0x10;
ctl_base += 0x10;
break;
@@ -312,7 +341,7 @@
msleep(100);
}
- if (hd < 0) {
+ if (hwif == NULL) {
printk(KERN_NOTICE "ide-cs: ide_register() at 0x%3lx & 0x%3lx"
", irq %u failed\n", io_base, ctl_base,
link->irq.AssignedIRQ);
@@ -320,10 +349,10 @@
}
info->ndev = 1;
- sprintf(info->node.dev_name, "hd%c", 'a' + (hd * 2));
- info->node.major = ide_major[hd];
+ sprintf(info->node.dev_name, "hd%c", 'a' + hwif->index * 2);
+ info->node.major = hwif->major;
info->node.minor = 0;
- info->hd = hd;
+ info->hwif = hwif;
link->dev_node = &info->node;
printk(KERN_INFO "ide-cs: %s: Vpp = %d.%d\n",
info->node.dev_name, link->conf.Vpp / 10, link->conf.Vpp % 10);
@@ -354,13 +383,14 @@
void ide_release(struct pcmcia_device *link)
{
ide_info_t *info = link->priv;
+ ide_hwif_t *hwif = info->hwif;
DEBUG(0, "ide_release(0x%p)\n", link);
if (info->ndev) {
/* FIXME: if this fails we need to queue the cleanup somehow
-- need to investigate the required PCMCIA magic */
- ide_unregister(info->hd);
+ ide_unregister(hwif->index);
}
info->ndev = 0;
diff --git a/drivers/ide/legacy/ide_platform.c b/drivers/ide/legacy/ide_platform.c
index bf24077..822f48b 100644
--- a/drivers/ide/legacy/ide_platform.c
+++ b/drivers/ide/legacy/ide_platform.c
@@ -100,7 +100,6 @@
hw.dev = &pdev->dev;
ide_init_port_hw(hwif, &hw);
- hwif->mmio = 1;
if (mmio)
default_hwif_mmiops(hwif);
diff --git a/drivers/ide/legacy/macide.c b/drivers/ide/legacy/macide.c
index 7429b80..26546d0 100644
--- a/drivers/ide/legacy/macide.c
+++ b/drivers/ide/legacy/macide.c
@@ -128,8 +128,6 @@
ide_init_port_data(hwif, index);
ide_init_port_hw(hwif, &hw);
- hwif->mmio = 1;
-
ide_device_add(idx, NULL);
}
diff --git a/drivers/ide/legacy/q40ide.c b/drivers/ide/legacy/q40ide.c
index fcbff0e..f23999d 100644
--- a/drivers/ide/legacy/q40ide.c
+++ b/drivers/ide/legacy/q40ide.c
@@ -141,7 +141,6 @@
if (hwif) {
ide_init_port_data(hwif, hwif->index);
ide_init_port_hw(hwif, &hw);
- hwif->mmio = 1;
idx[i] = hwif->index;
}
diff --git a/drivers/ide/legacy/qd65xx.c b/drivers/ide/legacy/qd65xx.c
index 6e820c7..15a99aa 100644
--- a/drivers/ide/legacy/qd65xx.c
+++ b/drivers/ide/legacy/qd65xx.c
@@ -37,6 +37,8 @@
#include <asm/system.h>
#include <asm/io.h>
+#define DRV_NAME "qd65xx"
+
#include "qd65xx.h"
/*
@@ -304,7 +306,20 @@
hwif->drives[1].drive_data = t2;
}
+static const struct ide_port_ops qd6500_port_ops = {
+ .port_init_devs = qd6500_port_init_devs,
+ .set_pio_mode = qd6500_set_pio_mode,
+ .selectproc = qd65xx_select,
+};
+
+static const struct ide_port_ops qd6580_port_ops = {
+ .port_init_devs = qd6580_port_init_devs,
+ .set_pio_mode = qd6580_set_pio_mode,
+ .selectproc = qd65xx_select,
+};
+
static const struct ide_port_info qd65xx_port_info __initdata = {
+ .name = DRV_NAME,
.chipset = ide_qd65xx,
.host_flags = IDE_HFLAG_IO_32BIT |
IDE_HFLAG_NO_DMA |
@@ -321,10 +336,8 @@
static int __init qd_probe(int base)
{
- ide_hwif_t *hwif;
- u8 config, unit;
- u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
- hw_regs_t hw[2];
+ int rc;
+ u8 config, unit, control;
struct ide_port_info d = qd65xx_port_info;
config = inb(QD_CONFIG_PORT);
@@ -337,21 +350,11 @@
if (unit)
d.host_flags |= IDE_HFLAG_QD_2ND_PORT;
- memset(&hw, 0, sizeof(hw));
-
- ide_std_init_ports(&hw[0], 0x1f0, 0x3f6);
- hw[0].irq = 14;
-
- ide_std_init_ports(&hw[1], 0x170, 0x376);
- hw[1].irq = 15;
-
- if ((config & 0xf0) == QD_CONFIG_QD6500) {
-
+ switch (config & 0xf0) {
+ case QD_CONFIG_QD6500:
if (qd_testreg(base))
return -ENODEV; /* bad register */
- /* qd6500 found */
-
if (config & QD_CONFIG_DISABLED) {
printk(KERN_WARNING "qd6500 is disabled !\n");
return -ENODEV;
@@ -361,37 +364,14 @@
printk(KERN_DEBUG "qd6500: config=%#x, ID3=%u\n",
config, QD_ID3);
+ d.port_ops = &qd6500_port_ops;
d.host_flags |= IDE_HFLAG_SINGLE;
-
- hwif = ide_find_port_slot(&d);
- if (hwif == NULL)
- return -ENOENT;
-
- ide_init_port_hw(hwif, &hw[unit]);
-
- hwif->config_data = (base << 8) | config;
-
- hwif->port_init_devs = qd6500_port_init_devs;
- hwif->set_pio_mode = qd6500_set_pio_mode;
- hwif->selectproc = qd65xx_select;
-
- idx[unit] = hwif->index;
-
- ide_device_add(idx, &d);
-
- return 1;
- }
-
- if (((config & 0xf0) == QD_CONFIG_QD6580_A) ||
- ((config & 0xf0) == QD_CONFIG_QD6580_B)) {
-
- u8 control;
-
+ break;
+ case QD_CONFIG_QD6580_A:
+ case QD_CONFIG_QD6580_B:
if (qd_testreg(base) || qd_testreg(base + 0x02))
return -ENODEV; /* bad registers */
- /* qd6580 found */
-
control = inb(QD_CONTROL_PORT);
printk(KERN_NOTICE "qd6580 at %#x\n", base);
@@ -400,63 +380,23 @@
outb(QD_DEF_CONTR, QD_CONTROL_PORT);
- if (control & QD_CONTR_SEC_DISABLED) {
- /* secondary disabled */
-
- printk(KERN_INFO "qd6580: single IDE board\n");
-
+ d.port_ops = &qd6580_port_ops;
+ if (control & QD_CONTR_SEC_DISABLED)
d.host_flags |= IDE_HFLAG_SINGLE;
- hwif = ide_find_port_slot(&d);
- if (hwif == NULL)
- return -ENOENT;
-
- ide_init_port_hw(hwif, &hw[unit]);
-
- hwif->config_data = (base << 8) | config;
-
- hwif->port_init_devs = qd6580_port_init_devs;
- hwif->set_pio_mode = qd6580_set_pio_mode;
- hwif->selectproc = qd65xx_select;
-
- idx[unit] = hwif->index;
-
- ide_device_add(idx, &d);
-
- return 1;
- } else {
- ide_hwif_t *mate;
-
- /* secondary enabled */
- printk(KERN_INFO "qd6580: dual IDE board\n");
-
- hwif = ide_find_port();
- if (hwif) {
- ide_init_port_hw(hwif, &hw[0]);
- hwif->config_data = (base << 8) | config;
- hwif->port_init_devs = qd6580_port_init_devs;
- hwif->set_pio_mode = qd6580_set_pio_mode;
- hwif->selectproc = qd65xx_select;
- idx[0] = hwif->index;
- }
-
- mate = ide_find_port();
- if (mate) {
- ide_init_port_hw(mate, &hw[1]);
- mate->config_data = (base << 8) | config;
- mate->port_init_devs = qd6580_port_init_devs;
- mate->set_pio_mode = qd6580_set_pio_mode;
- mate->selectproc = qd65xx_select;
- idx[1] = mate->index;
- }
-
- ide_device_add(idx, &qd65xx_port_info);
-
- return 0; /* no other qd65xx possible */
- }
+ printk(KERN_INFO "qd6580: %s IDE board\n",
+ (control & QD_CONTR_SEC_DISABLED) ? "single" : "dual");
+ break;
+ default:
+ return -ENODEV;
}
- /* no qd65xx found */
- return -ENODEV;
+
+ rc = ide_legacy_device_add(&d, (base << 8) | config);
+
+ if (d.host_flags & IDE_HFLAG_SINGLE)
+ return (rc == 0) ? 1 : rc;
+
+ return rc;
}
int probe_qd65xx = 0;
diff --git a/drivers/ide/legacy/umc8672.c b/drivers/ide/legacy/umc8672.c
index 4d90bad..17d5153 100644
--- a/drivers/ide/legacy/umc8672.c
+++ b/drivers/ide/legacy/umc8672.c
@@ -51,6 +51,8 @@
#include <asm/io.h>
+#define DRV_NAME "umc8672"
+
/*
* Default speeds. These can be changed with "auto-tune" and/or hdparm.
*/
@@ -120,18 +122,21 @@
spin_unlock_irqrestore(&ide_lock, flags);
}
+static const struct ide_port_ops umc8672_port_ops = {
+ .set_pio_mode = umc_set_pio_mode,
+};
+
static const struct ide_port_info umc8672_port_info __initdata = {
+ .name = DRV_NAME,
.chipset = ide_umc8672,
+ .port_ops = &umc8672_port_ops,
.host_flags = IDE_HFLAG_NO_DMA | IDE_HFLAG_NO_AUTOTUNE,
.pio_mask = ATA_PIO4,
};
static int __init umc8672_probe(void)
{
- ide_hwif_t *hwif, *mate;
unsigned long flags;
- static u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
- hw_regs_t hw[2];
if (!request_region(0x108, 2, "umc8672")) {
printk(KERN_ERR "umc8672: ports 0x108-0x109 already in use.\n");
@@ -150,31 +155,7 @@
umc_set_speeds(current_speeds);
local_irq_restore(flags);
- memset(&hw, 0, sizeof(hw));
-
- ide_std_init_ports(&hw[0], 0x1f0, 0x3f6);
- hw[0].irq = 14;
-
- ide_std_init_ports(&hw[1], 0x170, 0x376);
- hw[1].irq = 15;
-
- hwif = ide_find_port();
- if (hwif) {
- ide_init_port_hw(hwif, &hw[0]);
- hwif->set_pio_mode = umc_set_pio_mode;
- idx[0] = hwif->index;
- }
-
- mate = ide_find_port();
- if (mate) {
- ide_init_port_hw(mate, &hw[1]);
- mate->set_pio_mode = umc_set_pio_mode;
- idx[1] = mate->index;
- }
-
- ide_device_add(idx, &umc8672_port_info);
-
- return 0;
+ return ide_legacy_device_add(&umc8672_port_info, 0);
}
int probe_umc8672;
diff --git a/drivers/ide/mips/au1xxx-ide.c b/drivers/ide/mips/au1xxx-ide.c
index a8cd003..3485a31 100644
--- a/drivers/ide/mips/au1xxx-ide.c
+++ b/drivers/ide/mips/au1xxx-ide.c
@@ -47,7 +47,6 @@
#define IDE_AU1XXX_BURSTMODE 1
static _auide_hwif auide_hwif;
-static int dbdma_init_done;
static int auide_ddma_init(_auide_hwif *auide);
@@ -61,7 +60,7 @@
if(!put_dest_flags(ahwif->rx_chan, (void*)addr, count << 1,
DDMA_FLAGS_NOIE)) {
- printk(KERN_ERR "%s failed %d\n", __FUNCTION__, __LINE__);
+ printk(KERN_ERR "%s failed %d\n", __func__, __LINE__);
return;
}
ctp = *((chan_tab_t **)ahwif->rx_chan);
@@ -79,7 +78,7 @@
if(!put_source_flags(ahwif->tx_chan, (void*)addr,
count << 1, DDMA_FLAGS_NOIE)) {
- printk(KERN_ERR "%s failed %d\n", __FUNCTION__, __LINE__);
+ printk(KERN_ERR "%s failed %d\n", __func__, __LINE__);
return;
}
ctp = *((chan_tab_t **)ahwif->tx_chan);
@@ -250,7 +249,7 @@
(void*) sg_virt(sg),
tc, flags)) {
printk(KERN_ERR "%s failed %d\n",
- __FUNCTION__, __LINE__);
+ __func__, __LINE__);
}
} else
{
@@ -258,7 +257,7 @@
(void*) sg_virt(sg),
tc, flags)) {
printk(KERN_ERR "%s failed %d\n",
- __FUNCTION__, __LINE__);
+ __func__, __LINE__);
}
}
@@ -315,35 +314,6 @@
return 0;
}
-static u8 auide_mdma_filter(ide_drive_t *drive)
-{
- /*
- * FIXME: ->white_list and ->black_list are based on completely bogus
- * ->ide_dma_check implementation which didn't set neither the host
- * controller timings nor the device for the desired transfer mode.
- *
- * They should be either removed or 0x00 MWDMA mask should be
- * returned for devices on the ->black_list.
- */
-
- if (dbdma_init_done == 0) {
- auide_hwif.white_list = ide_in_drive_list(drive->id,
- dma_white_list);
- auide_hwif.black_list = ide_in_drive_list(drive->id,
- dma_black_list);
- auide_hwif.drive = drive;
- auide_ddma_init(&auide_hwif);
- dbdma_init_done = 1;
- }
-
- /* Is the drive in our DMA black list? */
- if (auide_hwif.black_list)
- printk(KERN_WARNING "%s: Disabling DMA for %s (blacklisted)\n",
- drive->name, drive->id->model);
-
- return drive->hwif->mwdma_mask;
-}
-
static int auide_dma_test_irq(ide_drive_t *drive)
{
if (drive->waiting_for_dma == 0)
@@ -396,41 +366,41 @@
dev->dev_devwidth = devwidth;
dev->dev_flags = flags;
}
-
-#if defined(CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA)
+#ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
static void auide_dma_timeout(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
printk(KERN_ERR "%s: DMA timeout occurred: ", drive->name);
- if (hwif->ide_dma_test_irq(drive))
+ if (auide_dma_test_irq(drive))
return;
- hwif->ide_dma_end(drive);
+ auide_dma_end(drive);
}
-
-static int auide_ddma_init(_auide_hwif *auide) {
-
+static const struct ide_dma_ops au1xxx_dma_ops = {
+ .dma_host_set = auide_dma_host_set,
+ .dma_setup = auide_dma_setup,
+ .dma_exec_cmd = auide_dma_exec_cmd,
+ .dma_start = auide_dma_start,
+ .dma_end = auide_dma_end,
+ .dma_test_irq = auide_dma_test_irq,
+ .dma_lost_irq = auide_dma_lost_irq,
+ .dma_timeout = auide_dma_timeout,
+};
+
+static int auide_ddma_init(ide_hwif_t *hwif, const struct ide_port_info *d)
+{
+ _auide_hwif *auide = (_auide_hwif *)hwif->hwif_data;
dbdev_tab_t source_dev_tab, target_dev_tab;
u32 dev_id, tsize, devwidth, flags;
- ide_hwif_t *hwif = auide->hwif;
dev_id = AU1XXX_ATA_DDMA_REQ;
- if (auide->white_list || auide->black_list) {
- tsize = 8;
- devwidth = 32;
- }
- else {
- tsize = 1;
- devwidth = 16;
-
- printk(KERN_ERR "au1xxx-ide: %s is not on ide driver whitelist.\n",auide_hwif.drive->id->model);
- printk(KERN_ERR " please read 'Documentation/mips/AU1xxx_IDE.README'");
- }
+ tsize = 8; /* 1 */
+ devwidth = 32; /* 16 */
#ifdef IDE_AU1XXX_BURSTMODE
flags = DEV_FLAGS_SYNC | DEV_FLAGS_BURSTABLE;
@@ -482,9 +452,9 @@
return 0;
}
#else
-
-static int auide_ddma_init( _auide_hwif *auide )
+static int auide_ddma_init(ide_hwif_t *hwif, const struct ide_port_info *d)
{
+ _auide_hwif *auide = (_auide_hwif *)hwif->hwif_data;
dbdev_tab_t source_dev_tab;
int flags;
@@ -543,9 +513,18 @@
*ata_regs = ahwif->regbase + (14 << AU1XXX_ATA_REG_OFFSET);
}
+static const struct ide_port_ops au1xxx_port_ops = {
+ .set_pio_mode = au1xxx_set_pio_mode,
+ .set_dma_mode = auide_set_dma_mode,
+};
+
static const struct ide_port_info au1xxx_port_info = {
+ .init_dma = auide_ddma_init,
+ .port_ops = &au1xxx_port_ops,
+#ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
+ .dma_ops = &au1xxx_dma_ops,
+#endif
.host_flags = IDE_HFLAG_POST_SET_MODE |
- IDE_HFLAG_NO_DMA | /* no SFF-style DMA */
IDE_HFLAG_NO_IO_32BIT |
IDE_HFLAG_UNMASK_IRQS,
.pio_mask = ATA_PIO4,
@@ -615,8 +594,6 @@
hwif->dev = dev;
- hwif->mmio = 1;
-
/* If the user has selected DDMA assisted copies,
then set up a few local I/O function entry points
*/
@@ -625,34 +602,12 @@
hwif->INSW = auide_insw;
hwif->OUTSW = auide_outsw;
#endif
-
- hwif->set_pio_mode = &au1xxx_set_pio_mode;
- hwif->set_dma_mode = &auide_set_dma_mode;
-
-#ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
- hwif->dma_timeout = &auide_dma_timeout;
-
- hwif->mdma_filter = &auide_mdma_filter;
-
- hwif->dma_host_set = &auide_dma_host_set;
- hwif->dma_exec_cmd = &auide_dma_exec_cmd;
- hwif->dma_start = &auide_dma_start;
- hwif->ide_dma_end = &auide_dma_end;
- hwif->dma_setup = &auide_dma_setup;
- hwif->ide_dma_test_irq = &auide_dma_test_irq;
- hwif->dma_lost_irq = &auide_dma_lost_irq;
-#endif
hwif->select_data = 0; /* no chipset-specific code */
hwif->config_data = 0; /* no chipset-specific code */
auide_hwif.hwif = hwif;
hwif->hwif_data = &auide_hwif;
-#ifdef CONFIG_BLK_DEV_IDE_AU1XXX_PIO_DBDMA
- auide_ddma_init(&auide_hwif);
- dbdma_init_done = 1;
-#endif
-
idx[0] = hwif->index;
ide_device_add(idx, &au1xxx_port_info);
diff --git a/drivers/ide/mips/swarm.c b/drivers/ide/mips/swarm.c
index bbe8d58..112fe56 100644
--- a/drivers/ide/mips/swarm.c
+++ b/drivers/ide/mips/swarm.c
@@ -110,10 +110,8 @@
/* Setup MMIO ops. */
default_hwif_mmiops(hwif);
- /* Prevent resource map manipulation. */
- hwif->mmio = 1;
+
hwif->chipset = ide_generic;
- hwif->noprobe = 0;
for (i = IDE_DATA_OFFSET; i <= IDE_STATUS_OFFSET; i++)
hwif->io_ports[i] =
diff --git a/drivers/ide/pci/aec62xx.c b/drivers/ide/pci/aec62xx.c
index c9ba15a..ca16f37 100644
--- a/drivers/ide/pci/aec62xx.c
+++ b/drivers/ide/pci/aec62xx.c
@@ -135,7 +135,7 @@
static void aec_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- drive->hwif->set_dma_mode(drive, pio + XFER_PIO_0);
+ drive->hwif->port_ops->set_dma_mode(drive, pio + XFER_PIO_0);
}
static unsigned int __devinit init_chipset_aec62xx(struct pci_dev *dev, const char *name)
@@ -175,27 +175,23 @@
return (ata66 & mask) ? ATA_CBL_PATA40 : ATA_CBL_PATA80;
}
-static void __devinit init_hwif_aec62xx(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
+static const struct ide_port_ops atp850_port_ops = {
+ .set_pio_mode = aec_set_pio_mode,
+ .set_dma_mode = aec6210_set_mode,
+};
- hwif->set_pio_mode = &aec_set_pio_mode;
-
- if (dev->device == PCI_DEVICE_ID_ARTOP_ATP850UF)
- hwif->set_dma_mode = &aec6210_set_mode;
- else {
- hwif->set_dma_mode = &aec6260_set_mode;
-
- hwif->cable_detect = atp86x_cable_detect;
- }
-}
+static const struct ide_port_ops atp86x_port_ops = {
+ .set_pio_mode = aec_set_pio_mode,
+ .set_dma_mode = aec6260_set_mode,
+ .cable_detect = atp86x_cable_detect,
+};
static const struct ide_port_info aec62xx_chipsets[] __devinitdata = {
{ /* 0 */
.name = "AEC6210",
.init_chipset = init_chipset_aec62xx,
- .init_hwif = init_hwif_aec62xx,
.enablebits = {{0x4a,0x02,0x02}, {0x4a,0x04,0x04}},
+ .port_ops = &atp850_port_ops,
.host_flags = IDE_HFLAG_SERIALIZE |
IDE_HFLAG_NO_ATAPI_DMA |
IDE_HFLAG_NO_DSC |
@@ -207,7 +203,7 @@
},{ /* 1 */
.name = "AEC6260",
.init_chipset = init_chipset_aec62xx,
- .init_hwif = init_hwif_aec62xx,
+ .port_ops = &atp86x_port_ops,
.host_flags = IDE_HFLAG_NO_ATAPI_DMA | IDE_HFLAG_NO_AUTODMA |
IDE_HFLAG_ABUSE_SET_DMA_MODE |
IDE_HFLAG_OFF_BOARD,
@@ -217,8 +213,8 @@
},{ /* 2 */
.name = "AEC6260R",
.init_chipset = init_chipset_aec62xx,
- .init_hwif = init_hwif_aec62xx,
.enablebits = {{0x4a,0x02,0x02}, {0x4a,0x04,0x04}},
+ .port_ops = &atp86x_port_ops,
.host_flags = IDE_HFLAG_NO_ATAPI_DMA |
IDE_HFLAG_ABUSE_SET_DMA_MODE |
IDE_HFLAG_NON_BOOTABLE,
@@ -228,7 +224,7 @@
},{ /* 3 */
.name = "AEC6280",
.init_chipset = init_chipset_aec62xx,
- .init_hwif = init_hwif_aec62xx,
+ .port_ops = &atp86x_port_ops,
.host_flags = IDE_HFLAG_NO_ATAPI_DMA |
IDE_HFLAG_ABUSE_SET_DMA_MODE |
IDE_HFLAG_OFF_BOARD,
@@ -238,8 +234,8 @@
},{ /* 4 */
.name = "AEC6280R",
.init_chipset = init_chipset_aec62xx,
- .init_hwif = init_hwif_aec62xx,
.enablebits = {{0x4a,0x02,0x02}, {0x4a,0x04,0x04}},
+ .port_ops = &atp86x_port_ops,
.host_flags = IDE_HFLAG_NO_ATAPI_DMA |
IDE_HFLAG_ABUSE_SET_DMA_MODE |
IDE_HFLAG_OFF_BOARD,
diff --git a/drivers/ide/pci/alim15x3.c b/drivers/ide/pci/alim15x3.c
index 3fa2d9f..b5a3bc3 100644
--- a/drivers/ide/pci/alim15x3.c
+++ b/drivers/ide/pci/alim15x3.c
@@ -610,7 +610,7 @@
}
/**
- * ata66_ali15x3 - check for UDMA 66 support
+ * ali_cable_detect - cable detection
* @hwif: IDE interface
*
* This checks if the controller and the cable are capable
@@ -620,7 +620,7 @@
* FIXME: frobs bits that are not defined on newer ALi devicea
*/
-static u8 __devinit ata66_ali15x3(ide_hwif_t *hwif)
+static u8 __devinit ali_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
unsigned long flags;
@@ -652,27 +652,7 @@
return cbl;
}
-/**
- * init_hwif_common_ali15x3 - Set up ALI IDE hardware
- * @hwif: IDE interface
- *
- * Initialize the IDE structure side of the ALi 15x3 driver.
- */
-
-static void __devinit init_hwif_common_ali15x3 (ide_hwif_t *hwif)
-{
- hwif->set_pio_mode = &ali_set_pio_mode;
- hwif->set_dma_mode = &ali_set_dma_mode;
- hwif->udma_filter = &ali_udma_filter;
-
- hwif->cable_detect = ata66_ali15x3;
-
- if (hwif->dma_base == 0)
- return;
-
- hwif->dma_setup = &ali15x3_dma_setup;
-}
-
+#ifndef CONFIG_SPARC64
/**
* init_hwif_ali15x3 - Initialize the ALI IDE x86 stuff
* @hwif: interface to configure
@@ -722,34 +702,66 @@
if(irq >= 0)
hwif->irq = irq;
}
-
- init_hwif_common_ali15x3(hwif);
}
+#endif
/**
* init_dma_ali15x3 - set up DMA on ALi15x3
* @hwif: IDE interface
- * @dmabase: DMA interface base PCI address
+ * @d: IDE port info
*
- * Set up the DMA functionality on the ALi 15x3. For the ALi
- * controllers this is generic so we can let the generic code do
- * the actual work.
+ * Set up the DMA functionality on the ALi 15x3.
*/
-static void __devinit init_dma_ali15x3 (ide_hwif_t *hwif, unsigned long dmabase)
+static int __devinit init_dma_ali15x3(ide_hwif_t *hwif,
+ const struct ide_port_info *d)
{
- if (m5229_revision < 0x20)
- return;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
+ unsigned long base = ide_pci_dma_base(hwif, d);
+
+ if (base == 0 || ide_pci_set_master(dev, d->name) < 0)
+ return -1;
+
if (!hwif->channel)
- outb(inb(dmabase + 2) & 0x60, dmabase + 2);
- ide_setup_dma(hwif, dmabase);
+ outb(inb(base + 2) & 0x60, base + 2);
+
+ printk(KERN_INFO " %s: BM-DMA at 0x%04lx-0x%04lx\n",
+ hwif->name, base, base + 7);
+
+ if (ide_allocate_dma_engine(hwif))
+ return -1;
+
+ ide_setup_dma(hwif, base);
+
+ return 0;
}
+static const struct ide_port_ops ali_port_ops = {
+ .set_pio_mode = ali_set_pio_mode,
+ .set_dma_mode = ali_set_dma_mode,
+ .udma_filter = ali_udma_filter,
+ .cable_detect = ali_cable_detect,
+};
+
+static const struct ide_dma_ops ali_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ali15x3_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = ide_dma_start,
+ .dma_end = __ide_dma_end,
+ .dma_test_irq = ide_dma_test_irq,
+ .dma_lost_irq = ide_dma_lost_irq,
+ .dma_timeout = ide_dma_timeout,
+};
+
static const struct ide_port_info ali15x3_chipset __devinitdata = {
.name = "ALI15X3",
.init_chipset = init_chipset_ali15x3,
+#ifndef CONFIG_SPARC64
.init_hwif = init_hwif_ali15x3,
+#endif
.init_dma = init_dma_ali15x3,
+ .port_ops = &ali_port_ops,
.pio_mask = ATA_PIO5,
.swdma_mask = ATA_SWDMA2,
.mwdma_mask = ATA_MWDMA2,
@@ -792,14 +804,17 @@
d.udma_mask = ATA_UDMA5;
else
d.udma_mask = ATA_UDMA6;
+
+ d.dma_ops = &ali_dma_ops;
+ } else {
+ d.host_flags |= IDE_HFLAG_NO_DMA;
+
+ d.mwdma_mask = d.swdma_mask = 0;
}
if (idx == 0)
d.host_flags |= IDE_HFLAG_CLEAR_SIMPLEX;
-#if defined(CONFIG_SPARC64)
- d.init_hwif = init_hwif_common_ali15x3;
-#endif /* CONFIG_SPARC64 */
return ide_setup_pci_device(dev, &d);
}
diff --git a/drivers/ide/pci/amd74xx.c b/drivers/ide/pci/amd74xx.c
index ff684d3..f7c8838 100644
--- a/drivers/ide/pci/amd74xx.c
+++ b/drivers/ide/pci/amd74xx.c
@@ -210,13 +210,14 @@
if (hwif->irq == 0) /* 0 is bogus but will do for now */
hwif->irq = pci_get_legacy_ide_irq(dev, hwif->channel);
-
- hwif->set_pio_mode = &amd_set_pio_mode;
- hwif->set_dma_mode = &amd_set_drive;
-
- hwif->cable_detect = amd_cable_detect;
}
+static const struct ide_port_ops amd_port_ops = {
+ .set_pio_mode = amd_set_pio_mode,
+ .set_dma_mode = amd_set_drive,
+ .cable_detect = amd_cable_detect,
+};
+
#define IDE_HFLAGS_AMD \
(IDE_HFLAG_PIO_NO_BLACKLIST | \
IDE_HFLAG_ABUSE_SET_DMA_MODE | \
@@ -230,6 +231,7 @@
.init_chipset = init_chipset_amd74xx, \
.init_hwif = init_hwif_amd74xx, \
.enablebits = {{0x40,0x02,0x02}, {0x40,0x01,0x01}}, \
+ .port_ops = &amd_port_ops, \
.host_flags = IDE_HFLAGS_AMD, \
.pio_mask = ATA_PIO5, \
.swdma_mask = swdma, \
@@ -243,6 +245,7 @@
.init_chipset = init_chipset_amd74xx, \
.init_hwif = init_hwif_amd74xx, \
.enablebits = {{0x50,0x02,0x02}, {0x50,0x01,0x01}}, \
+ .port_ops = &amd_port_ops, \
.host_flags = IDE_HFLAGS_AMD, \
.pio_mask = ATA_PIO5, \
.swdma_mask = ATA_SWDMA2, \
diff --git a/drivers/ide/pci/atiixp.c b/drivers/ide/pci/atiixp.c
index 91722f8..8b63718 100644
--- a/drivers/ide/pci/atiixp.c
+++ b/drivers/ide/pci/atiixp.c
@@ -130,35 +130,25 @@
return ATA_CBL_PATA40;
}
-/**
- * init_hwif_atiixp - fill in the hwif for the ATIIXP
- * @hwif: IDE interface
- *
- * Set up the ide_hwif_t for the ATIIXP interface according to the
- * capabilities of the hardware.
- */
-
-static void __devinit init_hwif_atiixp(ide_hwif_t *hwif)
-{
- hwif->set_pio_mode = &atiixp_set_pio_mode;
- hwif->set_dma_mode = &atiixp_set_dma_mode;
-
- hwif->cable_detect = atiixp_cable_detect;
-}
+static const struct ide_port_ops atiixp_port_ops = {
+ .set_pio_mode = atiixp_set_pio_mode,
+ .set_dma_mode = atiixp_set_dma_mode,
+ .cable_detect = atiixp_cable_detect,
+};
static const struct ide_port_info atiixp_pci_info[] __devinitdata = {
{ /* 0 */
.name = "ATIIXP",
- .init_hwif = init_hwif_atiixp,
.enablebits = {{0x48,0x01,0x00}, {0x48,0x08,0x00}},
+ .port_ops = &atiixp_port_ops,
.host_flags = IDE_HFLAG_LEGACY_IRQS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
},{ /* 1 */
.name = "SB600_PATA",
- .init_hwif = init_hwif_atiixp,
.enablebits = {{0x48,0x01,0x00}, {0x00,0x00,0x00}},
+ .port_ops = &atiixp_port_ops,
.host_flags = IDE_HFLAG_SINGLE | IDE_HFLAG_LEGACY_IRQS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
diff --git a/drivers/ide/pci/cmd640.c b/drivers/ide/pci/cmd640.c
index b076dbf..25c2f1b 100644
--- a/drivers/ide/pci/cmd640.c
+++ b/drivers/ide/pci/cmd640.c
@@ -109,6 +109,8 @@
#include <asm/io.h>
+#define DRV_NAME "cmd640"
+
/*
* This flag is set in ide.c by the parameter: ide0=cmd640_vlb
*/
@@ -633,6 +635,9 @@
display_clocks(index);
}
+static const struct ide_port_ops cmd640_port_ops = {
+ .set_pio_mode = cmd640_set_pio_mode,
+};
#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
static int pci_conf1(void)
@@ -678,10 +683,29 @@
IDE_HFLAG_ABUSE_PREFETCH |
IDE_HFLAG_ABUSE_FAST_DEVSEL,
#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
+ .port_ops = &cmd640_port_ops,
.pio_mask = ATA_PIO5,
#endif
};
+static int cmd640x_init_one(unsigned long base, unsigned long ctl)
+{
+ if (!request_region(base, 8, DRV_NAME)) {
+ printk(KERN_ERR "%s: I/O resource 0x%lX-0x%lX not free.\n",
+ DRV_NAME, base, base + 7);
+ return -EBUSY;
+ }
+
+ if (!request_region(ctl, 1, DRV_NAME)) {
+ printk(KERN_ERR "%s: I/O resource 0x%lX not free.\n",
+ DRV_NAME, ctl);
+ release_region(base, 8);
+ return -EBUSY;
+ }
+
+ return 0;
+}
+
/*
* Probe for a cmd640 chipset, and initialize it if found.
*/
@@ -690,7 +714,7 @@
#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
int second_port_toggled = 0;
#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
- int second_port_cmd640 = 0;
+ int second_port_cmd640 = 0, rc;
const char *bus_type, *port2;
unsigned int index;
u8 b, cfr;
@@ -734,6 +758,17 @@
return 0;
}
+ rc = cmd640x_init_one(0x1f0, 0x3f6);
+ if (rc)
+ return rc;
+
+ rc = cmd640x_init_one(0x170, 0x376);
+ if (rc) {
+ release_region(0x3f6, 1);
+ release_region(0x1f0, 8);
+ return rc;
+ }
+
memset(&hw, 0, sizeof(hw));
ide_std_init_ports(&hw[0], 0x1f0, 0x3f6);
@@ -752,10 +787,6 @@
*/
if (cmd_hwif0) {
ide_init_port_hw(cmd_hwif0, &hw[0]);
-#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
- cmd_hwif0->set_pio_mode = &cmd640_set_pio_mode;
-#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
-
idx[0] = cmd_hwif0->index;
}
@@ -808,10 +839,6 @@
*/
if (second_port_cmd640 && cmd_hwif1) {
ide_init_port_hw(cmd_hwif1, &hw[1]);
-#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
- cmd_hwif1->set_pio_mode = &cmd640_set_pio_mode;
-#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
-
idx[1] = cmd_hwif1->index;
}
printk(KERN_INFO "cmd640: %sserialized, secondary interface %s\n",
diff --git a/drivers/ide/pci/cmd64x.c b/drivers/ide/pci/cmd64x.c
index 8baccfe..006fb62 100644
--- a/drivers/ide/pci/cmd64x.c
+++ b/drivers/ide/pci/cmd64x.c
@@ -223,7 +223,7 @@
(void) pci_write_config_byte(dev, pciU, regU);
}
-static int cmd648_ide_dma_end (ide_drive_t *drive)
+static int cmd648_dma_end(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
unsigned long base = hwif->dma_base - (hwif->channel * 8);
@@ -239,7 +239,7 @@
return err;
}
-static int cmd64x_ide_dma_end (ide_drive_t *drive)
+static int cmd64x_dma_end(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = to_pci_dev(hwif->dev);
@@ -256,7 +256,7 @@
return err;
}
-static int cmd648_ide_dma_test_irq (ide_drive_t *drive)
+static int cmd648_dma_test_irq(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
unsigned long base = hwif->dma_base - (hwif->channel * 8);
@@ -279,7 +279,7 @@
return 0;
}
-static int cmd64x_ide_dma_test_irq (ide_drive_t *drive)
+static int cmd64x_dma_test_irq(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = to_pci_dev(hwif->dev);
@@ -310,7 +310,7 @@
* event order for DMA transfers.
*/
-static int cmd646_1_ide_dma_end (ide_drive_t *drive)
+static int cmd646_1_dma_end(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
u8 dma_stat = 0, dma_cmd = 0;
@@ -370,7 +370,7 @@
return 0;
}
-static u8 __devinit ata66_cmd64x(ide_hwif_t *hwif)
+static u8 __devinit cmd64x_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
u8 bmidecsr = 0, mask = hwif->channel ? 0x02 : 0x01;
@@ -385,60 +385,52 @@
}
}
-static void __devinit init_hwif_cmd64x(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
+static const struct ide_port_ops cmd64x_port_ops = {
+ .set_pio_mode = cmd64x_set_pio_mode,
+ .set_dma_mode = cmd64x_set_dma_mode,
+ .cable_detect = cmd64x_cable_detect,
+};
- hwif->set_pio_mode = &cmd64x_set_pio_mode;
- hwif->set_dma_mode = &cmd64x_set_dma_mode;
+static const struct ide_dma_ops cmd64x_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ide_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = ide_dma_start,
+ .dma_end = cmd64x_dma_end,
+ .dma_test_irq = cmd64x_dma_test_irq,
+ .dma_lost_irq = ide_dma_lost_irq,
+ .dma_timeout = ide_dma_timeout,
+};
- hwif->cable_detect = ata66_cmd64x;
+static const struct ide_dma_ops cmd646_rev1_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ide_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = ide_dma_start,
+ .dma_end = cmd646_1_dma_end,
+ .dma_test_irq = ide_dma_test_irq,
+ .dma_lost_irq = ide_dma_lost_irq,
+ .dma_timeout = ide_dma_timeout,
+};
- if (!hwif->dma_base)
- return;
-
- /*
- * UltraDMA only supported on PCI646U and PCI646U2, which
- * correspond to revisions 0x03, 0x05 and 0x07 respectively.
- * Actually, although the CMD tech support people won't
- * tell me the details, the 0x03 revision cannot support
- * UDMA correctly without hardware modifications, and even
- * then it only works with Quantum disks due to some
- * hold time assumptions in the 646U part which are fixed
- * in the 646U2.
- *
- * So we only do UltraDMA on revision 0x05 and 0x07 chipsets.
- */
- if (dev->device == PCI_DEVICE_ID_CMD_646 && dev->revision < 5)
- hwif->ultra_mask = 0x00;
-
- switch (dev->device) {
- case PCI_DEVICE_ID_CMD_648:
- case PCI_DEVICE_ID_CMD_649:
- alt_irq_bits:
- hwif->ide_dma_end = &cmd648_ide_dma_end;
- hwif->ide_dma_test_irq = &cmd648_ide_dma_test_irq;
- break;
- case PCI_DEVICE_ID_CMD_646:
- if (dev->revision == 0x01) {
- hwif->ide_dma_end = &cmd646_1_ide_dma_end;
- break;
- } else if (dev->revision >= 0x03)
- goto alt_irq_bits;
- /* fall thru */
- default:
- hwif->ide_dma_end = &cmd64x_ide_dma_end;
- hwif->ide_dma_test_irq = &cmd64x_ide_dma_test_irq;
- break;
- }
-}
+static const struct ide_dma_ops cmd648_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ide_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = ide_dma_start,
+ .dma_end = cmd648_dma_end,
+ .dma_test_irq = cmd648_dma_test_irq,
+ .dma_lost_irq = ide_dma_lost_irq,
+ .dma_timeout = ide_dma_timeout,
+};
static const struct ide_port_info cmd64x_chipsets[] __devinitdata = {
{ /* 0 */
.name = "CMD643",
.init_chipset = init_chipset_cmd64x,
- .init_hwif = init_hwif_cmd64x,
.enablebits = {{0x00,0x00,0x00}, {0x51,0x08,0x08}},
+ .port_ops = &cmd64x_port_ops,
+ .dma_ops = &cmd64x_dma_ops,
.host_flags = IDE_HFLAG_CLEAR_SIMPLEX |
IDE_HFLAG_ABUSE_PREFETCH,
.pio_mask = ATA_PIO5,
@@ -447,9 +439,10 @@
},{ /* 1 */
.name = "CMD646",
.init_chipset = init_chipset_cmd64x,
- .init_hwif = init_hwif_cmd64x,
.enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
.chipset = ide_cmd646,
+ .port_ops = &cmd64x_port_ops,
+ .dma_ops = &cmd648_dma_ops,
.host_flags = IDE_HFLAG_ABUSE_PREFETCH,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
@@ -457,8 +450,9 @@
},{ /* 2 */
.name = "CMD648",
.init_chipset = init_chipset_cmd64x,
- .init_hwif = init_hwif_cmd64x,
.enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
+ .port_ops = &cmd64x_port_ops,
+ .dma_ops = &cmd648_dma_ops,
.host_flags = IDE_HFLAG_ABUSE_PREFETCH,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
@@ -466,8 +460,9 @@
},{ /* 3 */
.name = "CMD649",
.init_chipset = init_chipset_cmd64x,
- .init_hwif = init_hwif_cmd64x,
.enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
+ .port_ops = &cmd64x_port_ops,
+ .dma_ops = &cmd648_dma_ops,
.host_flags = IDE_HFLAG_ABUSE_PREFETCH,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
@@ -482,12 +477,35 @@
d = cmd64x_chipsets[idx];
- /*
- * The original PCI0646 didn't have the primary channel enable bit,
- * it appeared starting with PCI0646U (i.e. revision ID 3).
- */
- if (idx == 1 && dev->revision < 3)
- d.enablebits[0].reg = 0;
+ if (idx == 1) {
+ /*
+ * UltraDMA only supported on PCI646U and PCI646U2, which
+ * correspond to revisions 0x03, 0x05 and 0x07 respectively.
+ * Actually, although the CMD tech support people won't
+ * tell me the details, the 0x03 revision cannot support
+ * UDMA correctly without hardware modifications, and even
+ * then it only works with Quantum disks due to some
+ * hold time assumptions in the 646U part which are fixed
+ * in the 646U2.
+ *
+ * So we only do UltraDMA on revision 0x05 and 0x07 chipsets.
+ */
+ if (dev->revision < 5) {
+ d.udma_mask = 0x00;
+ /*
+ * The original PCI0646 didn't have the primary
+ * channel enable bit, it appeared starting with
+ * PCI0646U (i.e. revision ID 3).
+ */
+ if (dev->revision < 3) {
+ d.enablebits[0].reg = 0;
+ if (dev->revision == 1)
+ d.dma_ops = &cmd646_rev1_dma_ops;
+ else
+ d.dma_ops = &cmd64x_dma_ops;
+ }
+ }
+ }
return ide_setup_pci_device(dev, &d);
}
diff --git a/drivers/ide/pci/cs5520.c b/drivers/ide/pci/cs5520.c
index 01b37ec..17669a4 100644
--- a/drivers/ide/pci/cs5520.c
+++ b/drivers/ide/pci/cs5520.c
@@ -103,21 +103,27 @@
ide_dma_host_set(drive, on);
}
-static void __devinit init_hwif_cs5520(ide_hwif_t *hwif)
-{
- hwif->set_pio_mode = &cs5520_set_pio_mode;
- hwif->set_dma_mode = &cs5520_set_dma_mode;
+static const struct ide_port_ops cs5520_port_ops = {
+ .set_pio_mode = cs5520_set_pio_mode,
+ .set_dma_mode = cs5520_set_dma_mode,
+};
- if (hwif->dma_base == 0)
- return;
-
- hwif->dma_host_set = &cs5520_dma_host_set;
-}
+static const struct ide_dma_ops cs5520_dma_ops = {
+ .dma_host_set = cs5520_dma_host_set,
+ .dma_setup = ide_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = ide_dma_start,
+ .dma_end = __ide_dma_end,
+ .dma_test_irq = ide_dma_test_irq,
+ .dma_lost_irq = ide_dma_lost_irq,
+ .dma_timeout = ide_dma_timeout,
+};
#define DECLARE_CS_DEV(name_str) \
{ \
.name = name_str, \
- .init_hwif = init_hwif_cs5520, \
+ .port_ops = &cs5520_port_ops, \
+ .dma_ops = &cs5520_dma_ops, \
.host_flags = IDE_HFLAG_ISA_PORTS | \
IDE_HFLAG_CS5520 | \
IDE_HFLAG_VDMA | \
diff --git a/drivers/ide/pci/cs5530.c b/drivers/ide/pci/cs5530.c
index 56a369c..f5534c1f 100644
--- a/drivers/ide/pci/cs5530.c
+++ b/drivers/ide/pci/cs5530.c
@@ -228,26 +228,25 @@
unsigned long basereg;
u32 d0_timings;
- hwif->set_pio_mode = &cs5530_set_pio_mode;
- hwif->set_dma_mode = &cs5530_set_dma_mode;
-
basereg = CS5530_BASEREG(hwif);
d0_timings = inl(basereg + 0);
if (CS5530_BAD_PIO(d0_timings))
outl(cs5530_pio_timings[(d0_timings >> 31) & 1][0], basereg + 0);
if (CS5530_BAD_PIO(inl(basereg + 8)))
outl(cs5530_pio_timings[(d0_timings >> 31) & 1][0], basereg + 8);
-
- if (hwif->dma_base == 0)
- return;
-
- hwif->udma_filter = cs5530_udma_filter;
}
+static const struct ide_port_ops cs5530_port_ops = {
+ .set_pio_mode = cs5530_set_pio_mode,
+ .set_dma_mode = cs5530_set_dma_mode,
+ .udma_filter = cs5530_udma_filter,
+};
+
static const struct ide_port_info cs5530_chipset __devinitdata = {
.name = "CS5530",
.init_chipset = init_chipset_cs5530,
.init_hwif = init_hwif_cs5530,
+ .port_ops = &cs5530_port_ops,
.host_flags = IDE_HFLAG_SERIALIZE |
IDE_HFLAG_POST_SET_MODE,
.pio_mask = ATA_PIO4,
diff --git a/drivers/ide/pci/cs5535.c b/drivers/ide/pci/cs5535.c
index c9685f2..99fe91a 100644
--- a/drivers/ide/pci/cs5535.c
+++ b/drivers/ide/pci/cs5535.c
@@ -166,25 +166,15 @@
return (bit & 1) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
}
-/****
- * init_hwif_cs5535 - Initialize one ide cannel
- * @hwif: Channel descriptor
- *
- * This gets invoked by the IDE driver once for each channel. It
- * performs channel-specific pre-initialization before drive probing.
- *
- */
-static void __devinit init_hwif_cs5535(ide_hwif_t *hwif)
-{
- hwif->set_pio_mode = &cs5535_set_pio_mode;
- hwif->set_dma_mode = &cs5535_set_dma_mode;
-
- hwif->cable_detect = cs5535_cable_detect;
-}
+static const struct ide_port_ops cs5535_port_ops = {
+ .set_pio_mode = cs5535_set_pio_mode,
+ .set_dma_mode = cs5535_set_dma_mode,
+ .cable_detect = cs5535_cable_detect,
+};
static const struct ide_port_info cs5535_chipset __devinitdata = {
.name = "CS5535",
- .init_hwif = init_hwif_cs5535,
+ .port_ops = &cs5535_port_ops,
.host_flags = IDE_HFLAG_SINGLE | IDE_HFLAG_POST_SET_MODE |
IDE_HFLAG_ABUSE_SET_DMA_MODE,
.pio_mask = ATA_PIO4,
diff --git a/drivers/ide/pci/cy82c693.c b/drivers/ide/pci/cy82c693.c
index 08eab7e..e30eae5 100644
--- a/drivers/ide/pci/cy82c693.c
+++ b/drivers/ide/pci/cy82c693.c
@@ -382,15 +382,6 @@
return 0;
}
-/*
- * the init function - called for each ide channel once
- */
-static void __devinit init_hwif_cy82c693(ide_hwif_t *hwif)
-{
- hwif->set_pio_mode = &cy82c693_set_pio_mode;
- hwif->set_dma_mode = &cy82c693_set_dma_mode;
-}
-
static void __devinit init_iops_cy82c693(ide_hwif_t *hwif)
{
static ide_hwif_t *primary;
@@ -404,11 +395,16 @@
}
}
+static const struct ide_port_ops cy82c693_port_ops = {
+ .set_pio_mode = cy82c693_set_pio_mode,
+ .set_dma_mode = cy82c693_set_dma_mode,
+};
+
static const struct ide_port_info cy82c693_chipset __devinitdata = {
.name = "CY82C693",
.init_chipset = init_chipset_cy82c693,
.init_iops = init_iops_cy82c693,
- .init_hwif = init_hwif_cy82c693,
+ .port_ops = &cy82c693_port_ops,
.chipset = ide_cy82c693,
.host_flags = IDE_HFLAG_SINGLE,
.pio_mask = ATA_PIO4,
diff --git a/drivers/ide/pci/delkin_cb.c b/drivers/ide/pci/delkin_cb.c
index 753b86f..c7b7e04 100644
--- a/drivers/ide/pci/delkin_cb.c
+++ b/drivers/ide/pci/delkin_cb.c
@@ -43,6 +43,10 @@
0x00, 0x00, 0x00, 0x00, 0xa4, 0x83, 0x02, 0x13,
};
+static const struct ide_port_ops delkin_cb_port_ops = {
+ .quirkproc = ide_undecoded_slave,
+};
+
static int __devinit
delkin_cb_probe (struct pci_dev *dev, const struct pci_device_id *id)
{
@@ -89,8 +93,7 @@
ide_init_port_data(hwif, i);
ide_init_port_hw(hwif, &hw);
- hwif->mmio = 1;
- hwif->quirkproc = &ide_undecoded_slave;
+ hwif->port_ops = &delkin_cb_port_ops;
idx[0] = i;
diff --git a/drivers/ide/pci/hpt34x.c b/drivers/ide/pci/hpt34x.c
index 9f2fc30..84c36c1 100644
--- a/drivers/ide/pci/hpt34x.c
+++ b/drivers/ide/pci/hpt34x.c
@@ -115,11 +115,10 @@
return dev->irq;
}
-static void __devinit init_hwif_hpt34x(ide_hwif_t *hwif)
-{
- hwif->set_pio_mode = &hpt34x_set_pio_mode;
- hwif->set_dma_mode = &hpt34x_set_mode;
-}
+static const struct ide_port_ops hpt34x_port_ops = {
+ .set_pio_mode = hpt34x_set_pio_mode,
+ .set_dma_mode = hpt34x_set_mode,
+};
#define IDE_HFLAGS_HPT34X \
(IDE_HFLAG_NO_ATAPI_DMA | \
@@ -131,16 +130,14 @@
{ /* 0 */
.name = "HPT343",
.init_chipset = init_chipset_hpt34x,
- .init_hwif = init_hwif_hpt34x,
- .extra = 16,
+ .port_ops = &hpt34x_port_ops,
.host_flags = IDE_HFLAGS_HPT34X | IDE_HFLAG_NON_BOOTABLE,
.pio_mask = ATA_PIO5,
},
{ /* 1 */
.name = "HPT345",
.init_chipset = init_chipset_hpt34x,
- .init_hwif = init_hwif_hpt34x,
- .extra = 16,
+ .port_ops = &hpt34x_port_ops,
.host_flags = IDE_HFLAGS_HPT34X | IDE_HFLAG_OFF_BOARD,
.pio_mask = ATA_PIO5,
#ifdef CONFIG_HPT34X_AUTODMA
diff --git a/drivers/ide/pci/hpt366.c b/drivers/ide/pci/hpt366.c
index a490906..8c02961 100644
--- a/drivers/ide/pci/hpt366.c
+++ b/drivers/ide/pci/hpt366.c
@@ -776,7 +776,7 @@
pci_read_config_byte(dev, 0x52, &mcr3);
pci_read_config_byte(dev, 0x5a, &scr1);
printk("%s: (%s) mcr1=0x%02x, mcr3=0x%02x, scr1=0x%02x\n",
- drive->name, __FUNCTION__, mcr1, mcr3, scr1);
+ drive->name, __func__, mcr1, mcr3, scr1);
if (scr1 & 0x10)
pci_write_config_byte(dev, 0x5a, scr1 & ~0x10);
ide_dma_lost_irq(drive);
@@ -808,7 +808,7 @@
hpt370_clear_engine(drive);
}
-static void hpt370_ide_dma_start(ide_drive_t *drive)
+static void hpt370_dma_start(ide_drive_t *drive)
{
#ifdef HPT_RESET_STATE_ENGINE
hpt370_clear_engine(drive);
@@ -816,7 +816,7 @@
ide_dma_start(drive);
}
-static int hpt370_ide_dma_end(ide_drive_t *drive)
+static int hpt370_dma_end(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
u8 dma_stat = inb(hwif->dma_status);
@@ -838,7 +838,7 @@
}
/* returns 1 if DMA IRQ issued, 0 otherwise */
-static int hpt374_ide_dma_test_irq(ide_drive_t *drive)
+static int hpt374_dma_test_irq(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = to_pci_dev(hwif->dev);
@@ -858,11 +858,11 @@
if (!drive->waiting_for_dma)
printk(KERN_WARNING "%s: (%s) called while not waiting\n",
- drive->name, __FUNCTION__);
+ drive->name, __func__);
return 0;
}
-static int hpt374_ide_dma_end(ide_drive_t *drive)
+static int hpt374_dma_end(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = to_pci_dev(hwif->dev);
@@ -1271,17 +1271,6 @@
/* Cache the channel's MISC. control registers' offset */
hwif->select_data = hwif->channel ? 0x54 : 0x50;
- hwif->set_pio_mode = &hpt3xx_set_pio_mode;
- hwif->set_dma_mode = &hpt3xx_set_mode;
-
- hwif->quirkproc = &hpt3xx_quirkproc;
- hwif->maskproc = &hpt3xx_maskproc;
-
- hwif->udma_filter = &hpt3xx_udma_filter;
- hwif->mdma_filter = &hpt3xx_mdma_filter;
-
- hwif->cable_detect = hpt3xx_cable_detect;
-
/*
* HPT3xxN chips have some complications:
*
@@ -1323,29 +1312,19 @@
if (new_mcr != old_mcr)
pci_write_config_byte(dev, hwif->select_data + 1, new_mcr);
-
- if (hwif->dma_base == 0)
- return;
-
- if (chip_type >= HPT374) {
- hwif->ide_dma_test_irq = &hpt374_ide_dma_test_irq;
- hwif->ide_dma_end = &hpt374_ide_dma_end;
- } else if (chip_type >= HPT370) {
- hwif->dma_start = &hpt370_ide_dma_start;
- hwif->ide_dma_end = &hpt370_ide_dma_end;
- hwif->dma_timeout = &hpt370_dma_timeout;
- } else
- hwif->dma_lost_irq = &hpt366_dma_lost_irq;
}
-static void __devinit init_dma_hpt366(ide_hwif_t *hwif, unsigned long dmabase)
+static int __devinit init_dma_hpt366(ide_hwif_t *hwif,
+ const struct ide_port_info *d)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
- u8 masterdma = 0, slavedma = 0;
- u8 dma_new = 0, dma_old = 0;
- unsigned long flags;
+ unsigned long flags, base = ide_pci_dma_base(hwif, d);
+ u8 dma_old, dma_new, masterdma = 0, slavedma = 0;
- dma_old = inb(dmabase + 2);
+ if (base == 0 || ide_pci_set_master(dev, d->name) < 0)
+ return -1;
+
+ dma_old = inb(base + 2);
local_irq_save(flags);
@@ -1356,11 +1335,21 @@
if (masterdma & 0x30) dma_new |= 0x20;
if ( slavedma & 0x30) dma_new |= 0x40;
if (dma_new != dma_old)
- outb(dma_new, dmabase + 2);
+ outb(dma_new, base + 2);
local_irq_restore(flags);
- ide_setup_dma(hwif, dmabase);
+ printk(KERN_INFO " %s: BM-DMA at 0x%04lx-0x%04lx\n",
+ hwif->name, base, base + 7);
+
+ hwif->extra_base = base + (hwif->channel ? 8 : 16);
+
+ if (ide_allocate_dma_engine(hwif))
+ return -1;
+
+ ide_setup_dma(hwif, base);
+
+ return 0;
}
static void __devinit hpt374_init(struct pci_dev *dev, struct pci_dev *dev2)
@@ -1416,6 +1405,49 @@
IDE_HFLAG_ABUSE_SET_DMA_MODE | \
IDE_HFLAG_OFF_BOARD)
+static const struct ide_port_ops hpt3xx_port_ops = {
+ .set_pio_mode = hpt3xx_set_pio_mode,
+ .set_dma_mode = hpt3xx_set_mode,
+ .quirkproc = hpt3xx_quirkproc,
+ .maskproc = hpt3xx_maskproc,
+ .mdma_filter = hpt3xx_mdma_filter,
+ .udma_filter = hpt3xx_udma_filter,
+ .cable_detect = hpt3xx_cable_detect,
+};
+
+static const struct ide_dma_ops hpt37x_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ide_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = ide_dma_start,
+ .dma_end = hpt374_dma_end,
+ .dma_test_irq = hpt374_dma_test_irq,
+ .dma_lost_irq = ide_dma_lost_irq,
+ .dma_timeout = ide_dma_timeout,
+};
+
+static const struct ide_dma_ops hpt370_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ide_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = hpt370_dma_start,
+ .dma_end = hpt370_dma_end,
+ .dma_test_irq = ide_dma_test_irq,
+ .dma_lost_irq = ide_dma_lost_irq,
+ .dma_timeout = hpt370_dma_timeout,
+};
+
+static const struct ide_dma_ops hpt36x_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ide_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = ide_dma_start,
+ .dma_end = __ide_dma_end,
+ .dma_test_irq = ide_dma_test_irq,
+ .dma_lost_irq = hpt366_dma_lost_irq,
+ .dma_timeout = ide_dma_timeout,
+};
+
static const struct ide_port_info hpt366_chipsets[] __devinitdata = {
{ /* 0 */
.name = "HPT36x",
@@ -1429,7 +1461,8 @@
* Bit 4 is for the primary channel, bit 5 for the secondary.
*/
.enablebits = {{0x50,0x10,0x10}, {0x54,0x04,0x04}},
- .extra = 240,
+ .port_ops = &hpt3xx_port_ops,
+ .dma_ops = &hpt36x_dma_ops,
.host_flags = IDE_HFLAGS_HPT3XX | IDE_HFLAG_SINGLE,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
@@ -1439,7 +1472,8 @@
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .extra = 240,
+ .port_ops = &hpt3xx_port_ops,
+ .dma_ops = &hpt37x_dma_ops,
.host_flags = IDE_HFLAGS_HPT3XX,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
@@ -1449,7 +1483,8 @@
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .extra = 240,
+ .port_ops = &hpt3xx_port_ops,
+ .dma_ops = &hpt37x_dma_ops,
.host_flags = IDE_HFLAGS_HPT3XX,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
@@ -1459,7 +1494,8 @@
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .extra = 240,
+ .port_ops = &hpt3xx_port_ops,
+ .dma_ops = &hpt37x_dma_ops,
.host_flags = IDE_HFLAGS_HPT3XX,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
@@ -1470,7 +1506,8 @@
.init_dma = init_dma_hpt366,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
.udma_mask = ATA_UDMA5,
- .extra = 240,
+ .port_ops = &hpt3xx_port_ops,
+ .dma_ops = &hpt37x_dma_ops,
.host_flags = IDE_HFLAGS_HPT3XX,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
@@ -1480,7 +1517,8 @@
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .extra = 240,
+ .port_ops = &hpt3xx_port_ops,
+ .dma_ops = &hpt37x_dma_ops,
.host_flags = IDE_HFLAGS_HPT3XX,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
@@ -1543,6 +1581,10 @@
d.name = info->chip_name;
d.udma_mask = info->udma_mask;
+ /* fixup ->dma_ops for HPT370/HPT370A */
+ if (info == &hpt370 || info == &hpt370a)
+ d.dma_ops = &hpt370_dma_ops;
+
pci_set_drvdata(dev, (void *)info);
if (info == &hpt36x || info == &hpt374)
diff --git a/drivers/ide/pci/it8213.c b/drivers/ide/pci/it8213.c
index 5b5b0cc4..9053c877 100644
--- a/drivers/ide/pci/it8213.c
+++ b/drivers/ide/pci/it8213.c
@@ -149,27 +149,17 @@
return (reg42h & 0x02) ? ATA_CBL_PATA40 : ATA_CBL_PATA80;
}
-/**
- * init_hwif_it8213 - set up hwif structs
- * @hwif: interface to set up
- *
- * We do the basic set up of the interface structure.
- */
-
-static void __devinit init_hwif_it8213(ide_hwif_t *hwif)
-{
- hwif->set_dma_mode = &it8213_set_dma_mode;
- hwif->set_pio_mode = &it8213_set_pio_mode;
-
- hwif->cable_detect = it8213_cable_detect;
-}
-
+static const struct ide_port_ops it8213_port_ops = {
+ .set_pio_mode = it8213_set_pio_mode,
+ .set_dma_mode = it8213_set_dma_mode,
+ .cable_detect = it8213_cable_detect,
+};
#define DECLARE_ITE_DEV(name_str) \
{ \
.name = name_str, \
- .init_hwif = init_hwif_it8213, \
.enablebits = { {0x41, 0x80, 0x80} }, \
+ .port_ops = &it8213_port_ops, \
.host_flags = IDE_HFLAG_SINGLE, \
.pio_mask = ATA_PIO4, \
.swdma_mask = ATA_SWDMA2_ONLY, \
diff --git a/drivers/ide/pci/it821x.c b/drivers/ide/pci/it821x.c
index a38ec47..6ab0411 100644
--- a/drivers/ide/pci/it821x.c
+++ b/drivers/ide/pci/it821x.c
@@ -418,7 +418,7 @@
}
/**
- * ata66_it821x - check for 80 pin cable
+ * it821x_cable_detect - cable detection
* @hwif: interface to check
*
* Check for the presence of an ATA66 capable cable on the
@@ -426,7 +426,7 @@
* the needed logic onboard.
*/
-static u8 __devinit ata66_it821x(ide_hwif_t *hwif)
+static u8 __devinit it821x_cable_detect(ide_hwif_t *hwif)
{
/* The reference driver also only does disk side */
return ATA_CBL_PATA80;
@@ -511,6 +511,11 @@
}
+static struct ide_dma_ops it821x_pass_through_dma_ops = {
+ .dma_start = it821x_dma_start,
+ .dma_end = it821x_dma_end,
+};
+
/**
* init_hwif_it821x - set up hwif structs
* @hwif: interface to set up
@@ -527,8 +532,6 @@
struct it821x_dev *idev = itdevs[hwif->channel];
u8 conf;
- hwif->quirkproc = &it821x_quirkproc;
-
ide_set_hwifdata(hwif, idev);
pci_read_config_byte(dev, 0x50, &conf);
@@ -563,17 +566,11 @@
}
if (idev->smart == 0) {
- hwif->set_pio_mode = &it821x_set_pio_mode;
- hwif->set_dma_mode = &it821x_set_dma_mode;
-
/* MWDMA/PIO clock switching for pass through mode */
- hwif->dma_start = &it821x_dma_start;
- hwif->ide_dma_end = &it821x_dma_end;
+ hwif->dma_ops = &it821x_pass_through_dma_ops;
} else
hwif->host_flags |= IDE_HFLAG_NO_SET_MODE;
- hwif->cable_detect = ata66_it821x;
-
if (hwif->dma_base == 0)
return;
@@ -613,12 +610,20 @@
return 0;
}
+static const struct ide_port_ops it821x_port_ops = {
+ /* it821x_set_{pio,dma}_mode() are only used in pass-through mode */
+ .set_pio_mode = it821x_set_pio_mode,
+ .set_dma_mode = it821x_set_dma_mode,
+ .quirkproc = it821x_quirkproc,
+ .cable_detect = it821x_cable_detect,
+};
#define DECLARE_ITE_DEV(name_str) \
{ \
.name = name_str, \
.init_chipset = init_chipset_it821x, \
.init_hwif = init_hwif_it821x, \
+ .port_ops = &it821x_port_ops, \
.pio_mask = ATA_PIO4, \
}
diff --git a/drivers/ide/pci/jmicron.c b/drivers/ide/pci/jmicron.c
index 673f7dc..96ef739 100644
--- a/drivers/ide/pci/jmicron.c
+++ b/drivers/ide/pci/jmicron.c
@@ -19,13 +19,13 @@
} port_type;
/**
- * ata66_jmicron - Cable check
+ * jmicron_cable_detect - cable detection
* @hwif: IDE port
*
* Returns the cable type.
*/
-static u8 __devinit ata66_jmicron(ide_hwif_t *hwif)
+static u8 __devinit jmicron_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *pdev = to_pci_dev(hwif->dev);
@@ -95,25 +95,16 @@
{
}
-/**
- * init_hwif_jmicron - set up hwif structs
- * @hwif: interface to set up
- *
- * Minimal set up is required for the Jmicron hardware.
- */
-
-static void __devinit init_hwif_jmicron(ide_hwif_t *hwif)
-{
- hwif->set_pio_mode = &jmicron_set_pio_mode;
- hwif->set_dma_mode = &jmicron_set_dma_mode;
-
- hwif->cable_detect = ata66_jmicron;
-}
+static const struct ide_port_ops jmicron_port_ops = {
+ .set_pio_mode = jmicron_set_pio_mode,
+ .set_dma_mode = jmicron_set_dma_mode,
+ .cable_detect = jmicron_cable_detect,
+};
static const struct ide_port_info jmicron_chipset __devinitdata = {
.name = "JMB",
- .init_hwif = init_hwif_jmicron,
.enablebits = { { 0x40, 0x01, 0x01 }, { 0x40, 0x10, 0x10 } },
+ .port_ops = &jmicron_port_ops,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
diff --git a/drivers/ide/pci/ns87415.c b/drivers/ide/pci/ns87415.c
index 3015d691..e1b0c9a 100644
--- a/drivers/ide/pci/ns87415.c
+++ b/drivers/ide/pci/ns87415.c
@@ -150,7 +150,7 @@
ns87415_prepare_drive (drive, drive->using_dma);
}
-static int ns87415_ide_dma_end (ide_drive_t *drive)
+static int ns87415_dma_end(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
u8 dma_stat = 0, dma_cmd = 0;
@@ -170,7 +170,7 @@
return (dma_stat & 7) != 4;
}
-static int ns87415_ide_dma_setup(ide_drive_t *drive)
+static int ns87415_dma_setup(ide_drive_t *drive)
{
/* select DMA xfer */
ns87415_prepare_drive(drive, 1);
@@ -195,8 +195,6 @@
u8 stat;
#endif
- hwif->selectproc = &ns87415_selectproc;
-
/*
* We cannot probe for IRQ: both ports share common IRQ on INTA.
* Also, leave IRQ masked during drive probing, to prevent infinite
@@ -254,16 +252,31 @@
return;
outb(0x60, hwif->dma_status);
- hwif->dma_setup = &ns87415_ide_dma_setup;
- hwif->ide_dma_end = &ns87415_ide_dma_end;
}
+static const struct ide_port_ops ns87415_port_ops = {
+ .selectproc = ns87415_selectproc,
+};
+
+static const struct ide_dma_ops ns87415_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ns87415_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = ide_dma_start,
+ .dma_end = ns87415_dma_end,
+ .dma_test_irq = ide_dma_test_irq,
+ .dma_lost_irq = ide_dma_lost_irq,
+ .dma_timeout = ide_dma_timeout,
+};
+
static const struct ide_port_info ns87415_chipset __devinitdata = {
.name = "NS87415",
#ifdef CONFIG_SUPERIO
.init_iops = init_iops_ns87415,
#endif
.init_hwif = init_hwif_ns87415,
+ .port_ops = &ns87415_port_ops,
+ .dma_ops = &ns87415_dma_ops,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA |
IDE_HFLAG_NO_ATAPI_DMA,
};
diff --git a/drivers/ide/pci/opti621.c b/drivers/ide/pci/opti621.c
index 88a4dd9..9edacba 100644
--- a/drivers/ide/pci/opti621.c
+++ b/drivers/ide/pci/opti621.c
@@ -326,28 +326,24 @@
hwif->drives[1].drive_data = PIO_DONT_KNOW;
}
-/*
- * init_hwif_opti621() is called once for each hwif found at boot.
- */
-static void __devinit init_hwif_opti621(ide_hwif_t *hwif)
-{
- hwif->port_init_devs = opti621_port_init_devs;
- hwif->set_pio_mode = &opti621_set_pio_mode;
-}
+static const struct ide_port_ops opti621_port_ops = {
+ .port_init_devs = opti621_port_init_devs,
+ .set_pio_mode = opti621_set_pio_mode,
+};
static const struct ide_port_info opti621_chipsets[] __devinitdata = {
{ /* 0 */
.name = "OPTI621",
- .init_hwif = init_hwif_opti621,
.enablebits = { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} },
+ .port_ops = &opti621_port_ops,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
.pio_mask = ATA_PIO3,
.swdma_mask = ATA_SWDMA2,
.mwdma_mask = ATA_MWDMA2,
}, { /* 1 */
.name = "OPTI621X",
- .init_hwif = init_hwif_opti621,
.enablebits = { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} },
+ .port_ops = &opti621_port_ops,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
.pio_mask = ATA_PIO3,
.swdma_mask = ATA_SWDMA2,
diff --git a/drivers/ide/pci/pdc202xx_new.c b/drivers/ide/pci/pdc202xx_new.c
index 1c8cb77..ec9bd7b 100644
--- a/drivers/ide/pci/pdc202xx_new.c
+++ b/drivers/ide/pci/pdc202xx_new.c
@@ -34,7 +34,7 @@
#undef DEBUG
#ifdef DEBUG
-#define DBG(fmt, args...) printk("%s: " fmt, __FUNCTION__, ## args)
+#define DBG(fmt, args...) printk("%s: " fmt, __func__, ## args)
#else
#define DBG(fmt, args...)
#endif
@@ -442,17 +442,6 @@
return dev->irq;
}
-static void __devinit init_hwif_pdc202new(ide_hwif_t *hwif)
-{
- hwif->set_pio_mode = &pdcnew_set_pio_mode;
- hwif->set_dma_mode = &pdcnew_set_dma_mode;
-
- hwif->quirkproc = &pdcnew_quirkproc;
- hwif->resetproc = &pdcnew_reset;
-
- hwif->cable_detect = pdcnew_cable_detect;
-}
-
static struct pci_dev * __devinit pdc20270_get_dev2(struct pci_dev *dev)
{
struct pci_dev *dev2;
@@ -476,11 +465,19 @@
return NULL;
}
+static const struct ide_port_ops pdcnew_port_ops = {
+ .set_pio_mode = pdcnew_set_pio_mode,
+ .set_dma_mode = pdcnew_set_dma_mode,
+ .quirkproc = pdcnew_quirkproc,
+ .resetproc = pdcnew_reset,
+ .cable_detect = pdcnew_cable_detect,
+};
+
#define DECLARE_PDCNEW_DEV(name_str, udma) \
{ \
.name = name_str, \
.init_chipset = init_chipset_pdcnew, \
- .init_hwif = init_hwif_pdc202new, \
+ .port_ops = &pdcnew_port_ops, \
.host_flags = IDE_HFLAG_POST_SET_MODE | \
IDE_HFLAG_ERROR_STOPS_FIFO | \
IDE_HFLAG_OFF_BOARD, \
diff --git a/drivers/ide/pci/pdc202xx_old.c b/drivers/ide/pci/pdc202xx_old.c
index 150422e..fca89ed 100644
--- a/drivers/ide/pci/pdc202xx_old.c
+++ b/drivers/ide/pci/pdc202xx_old.c
@@ -115,7 +115,7 @@
pdc202xx_set_mode(drive, XFER_PIO_0 + pio);
}
-static u8 __devinit pdc2026x_old_cable_detect(ide_hwif_t *hwif)
+static u8 __devinit pdc2026x_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
u16 CIS, mask = hwif->channel ? (1 << 11) : (1 << 10);
@@ -163,7 +163,7 @@
drive->quirk_list = 0;
}
-static void pdc202xx_old_ide_dma_start(ide_drive_t *drive)
+static void pdc202xx_dma_start(ide_drive_t *drive)
{
if (drive->current_speed > XFER_UDMA_2)
pdc_old_enable_66MHz_clock(drive->hwif);
@@ -185,7 +185,7 @@
ide_dma_start(drive);
}
-static int pdc202xx_old_ide_dma_end(ide_drive_t *drive)
+static int pdc202xx_dma_end(ide_drive_t *drive)
{
if (drive->media != ide_disk || drive->addressing == 1) {
ide_hwif_t *hwif = HWIF(drive);
@@ -202,7 +202,7 @@
return __ide_dma_end(drive);
}
-static int pdc202xx_old_ide_dma_test_irq(ide_drive_t *drive)
+static int pdc202xx_dma_test_irq(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
unsigned long high_16 = hwif->extra_base - 16;
@@ -226,26 +226,6 @@
return (dma_stat & 4) == 4; /* return 1 if INTR asserted */
}
-static void pdc202xx_dma_lost_irq(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = HWIF(drive);
-
- if (hwif->resetproc != NULL)
- hwif->resetproc(drive);
-
- ide_dma_lost_irq(drive);
-}
-
-static void pdc202xx_dma_timeout(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = HWIF(drive);
-
- if (hwif->resetproc != NULL)
- hwif->resetproc(drive);
-
- ide_dma_timeout(drive);
-}
-
static void pdc202xx_reset_host (ide_hwif_t *hwif)
{
unsigned long high_16 = hwif->extra_base - 16;
@@ -271,68 +251,46 @@
ide_set_max_pio(drive);
}
+static void pdc202xx_dma_lost_irq(ide_drive_t *drive)
+{
+ pdc202xx_reset(drive);
+ ide_dma_lost_irq(drive);
+}
+
+static void pdc202xx_dma_timeout(ide_drive_t *drive)
+{
+ pdc202xx_reset(drive);
+ ide_dma_timeout(drive);
+}
+
static unsigned int __devinit init_chipset_pdc202xx(struct pci_dev *dev,
- const char *name)
+ const char *name)
{
- return dev->irq;
-}
-
-static void __devinit init_hwif_pdc202xx(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
-
- hwif->set_pio_mode = &pdc202xx_set_pio_mode;
- hwif->set_dma_mode = &pdc202xx_set_mode;
-
- hwif->quirkproc = &pdc202xx_quirkproc;
-
- if (dev->device != PCI_DEVICE_ID_PROMISE_20246) {
- hwif->resetproc = &pdc202xx_reset;
-
- hwif->cable_detect = pdc2026x_old_cable_detect;
- }
-
- if (hwif->dma_base == 0)
- return;
-
- hwif->dma_lost_irq = &pdc202xx_dma_lost_irq;
- hwif->dma_timeout = &pdc202xx_dma_timeout;
-
- if (dev->device != PCI_DEVICE_ID_PROMISE_20246) {
- hwif->dma_start = &pdc202xx_old_ide_dma_start;
- hwif->ide_dma_end = &pdc202xx_old_ide_dma_end;
- }
- hwif->ide_dma_test_irq = &pdc202xx_old_ide_dma_test_irq;
-}
-
-static void __devinit init_dma_pdc202xx(ide_hwif_t *hwif, unsigned long dmabase)
-{
+ unsigned long dmabase = pci_resource_start(dev, 4);
u8 udma_speed_flag = 0, primary_mode = 0, secondary_mode = 0;
- if (hwif->channel) {
- ide_setup_dma(hwif, dmabase);
- return;
- }
+ if (dmabase == 0)
+ goto out;
udma_speed_flag = inb(dmabase | 0x1f);
primary_mode = inb(dmabase | 0x1a);
secondary_mode = inb(dmabase | 0x1b);
printk(KERN_INFO "%s: (U)DMA Burst Bit %sABLED " \
"Primary %s Mode " \
- "Secondary %s Mode.\n", hwif->cds->name,
+ "Secondary %s Mode.\n", pci_name(dev),
(udma_speed_flag & 1) ? "EN" : "DIS",
(primary_mode & 1) ? "MASTER" : "PCI",
(secondary_mode & 1) ? "MASTER" : "PCI" );
if (!(udma_speed_flag & 1)) {
printk(KERN_INFO "%s: FORCING BURST BIT 0x%02x->0x%02x ",
- hwif->cds->name, udma_speed_flag,
+ pci_name(dev), udma_speed_flag,
(udma_speed_flag|1));
outb(udma_speed_flag | 1, dmabase | 0x1f);
printk("%sACTIVE\n", (inb(dmabase | 0x1f) & 1) ? "" : "IN");
}
-
- ide_setup_dma(hwif, dmabase);
+out:
+ return dev->irq;
}
static void __devinit pdc202ata4_fixup_irq(struct pci_dev *dev,
@@ -357,13 +315,48 @@
IDE_HFLAG_ABUSE_SET_DMA_MODE | \
IDE_HFLAG_OFF_BOARD)
+static const struct ide_port_ops pdc20246_port_ops = {
+ .set_pio_mode = pdc202xx_set_pio_mode,
+ .set_dma_mode = pdc202xx_set_mode,
+ .quirkproc = pdc202xx_quirkproc,
+};
+
+static const struct ide_port_ops pdc2026x_port_ops = {
+ .set_pio_mode = pdc202xx_set_pio_mode,
+ .set_dma_mode = pdc202xx_set_mode,
+ .quirkproc = pdc202xx_quirkproc,
+ .resetproc = pdc202xx_reset,
+ .cable_detect = pdc2026x_cable_detect,
+};
+
+static const struct ide_dma_ops pdc20246_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ide_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = ide_dma_start,
+ .dma_end = __ide_dma_end,
+ .dma_test_irq = pdc202xx_dma_test_irq,
+ .dma_lost_irq = pdc202xx_dma_lost_irq,
+ .dma_timeout = pdc202xx_dma_timeout,
+};
+
+static const struct ide_dma_ops pdc2026x_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ide_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = pdc202xx_dma_start,
+ .dma_end = pdc202xx_dma_end,
+ .dma_test_irq = pdc202xx_dma_test_irq,
+ .dma_lost_irq = pdc202xx_dma_lost_irq,
+ .dma_timeout = pdc202xx_dma_timeout,
+};
+
#define DECLARE_PDC2026X_DEV(name_str, udma, extra_flags) \
{ \
.name = name_str, \
.init_chipset = init_chipset_pdc202xx, \
- .init_hwif = init_hwif_pdc202xx, \
- .init_dma = init_dma_pdc202xx, \
- .extra = 48, \
+ .port_ops = &pdc2026x_port_ops, \
+ .dma_ops = &pdc2026x_dma_ops, \
.host_flags = IDE_HFLAGS_PDC202XX | extra_flags, \
.pio_mask = ATA_PIO4, \
.mwdma_mask = ATA_MWDMA2, \
@@ -374,9 +367,8 @@
{ /* 0 */
.name = "PDC20246",
.init_chipset = init_chipset_pdc202xx,
- .init_hwif = init_hwif_pdc202xx,
- .init_dma = init_dma_pdc202xx,
- .extra = 16,
+ .port_ops = &pdc20246_port_ops,
+ .dma_ops = &pdc20246_dma_ops,
.host_flags = IDE_HFLAGS_PDC202XX,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
diff --git a/drivers/ide/pci/piix.c b/drivers/ide/pci/piix.c
index 89d74ff..21c5dd2 100644
--- a/drivers/ide/pci/piix.c
+++ b/drivers/ide/pci/piix.c
@@ -285,11 +285,6 @@
static void __devinit init_hwif_piix(ide_hwif_t *hwif)
{
- hwif->set_pio_mode = &piix_set_pio_mode;
- hwif->set_dma_mode = &piix_set_dma_mode;
-
- hwif->cable_detect = piix_cable_detect;
-
if (!hwif->dma_base)
return;
@@ -306,6 +301,12 @@
hwif->ide_dma_clear_irq = &piix_dma_clear_irq;
}
+static const struct ide_port_ops piix_port_ops = {
+ .set_pio_mode = piix_set_pio_mode,
+ .set_dma_mode = piix_set_dma_mode,
+ .cable_detect = piix_cable_detect,
+};
+
#ifndef CONFIG_IA64
#define IDE_HFLAGS_PIIX IDE_HFLAG_LEGACY_IRQS
#else
@@ -317,6 +318,7 @@
.name = name_str, \
.init_hwif = init_hwif_piix, \
.enablebits = {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, \
+ .port_ops = &piix_port_ops, \
.host_flags = IDE_HFLAGS_PIIX, \
.pio_mask = ATA_PIO4, \
.swdma_mask = ATA_SWDMA2_ONLY, \
@@ -330,6 +332,7 @@
.init_chipset = init_chipset_ich, \
.init_hwif = init_hwif_ich, \
.enablebits = {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, \
+ .port_ops = &piix_port_ops, \
.host_flags = IDE_HFLAGS_PIIX, \
.pio_mask = ATA_PIO4, \
.swdma_mask = ATA_SWDMA2_ONLY, \
diff --git a/drivers/ide/pci/sc1200.c b/drivers/ide/pci/sc1200.c
index 44985c8..14c787b 100644
--- a/drivers/ide/pci/sc1200.c
+++ b/drivers/ide/pci/sc1200.c
@@ -165,7 +165,7 @@
*
* returns 1 on error, 0 otherwise
*/
-static int sc1200_ide_dma_end (ide_drive_t *drive)
+static int sc1200_dma_end(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
unsigned long dma_base = hwif->dma_base;
@@ -214,7 +214,7 @@
printk("SC1200: %s: changing (U)DMA mode\n", drive->name);
ide_dma_off_quietly(drive);
if (ide_set_dma_mode(drive, mode) == 0 && drive->using_dma)
- hwif->dma_host_set(drive, 1);
+ hwif->dma_ops->dma_host_set(drive, 1);
return;
}
@@ -286,25 +286,27 @@
}
#endif
-/*
- * This gets invoked by the IDE driver once for each channel,
- * and performs channel-specific pre-initialization before drive probing.
- */
-static void __devinit init_hwif_sc1200 (ide_hwif_t *hwif)
-{
- hwif->set_pio_mode = &sc1200_set_pio_mode;
- hwif->set_dma_mode = &sc1200_set_dma_mode;
+static const struct ide_port_ops sc1200_port_ops = {
+ .set_pio_mode = sc1200_set_pio_mode,
+ .set_dma_mode = sc1200_set_dma_mode,
+ .udma_filter = sc1200_udma_filter,
+};
- if (hwif->dma_base == 0)
- return;
-
- hwif->udma_filter = sc1200_udma_filter;
- hwif->ide_dma_end = &sc1200_ide_dma_end;
-}
+static const struct ide_dma_ops sc1200_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ide_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = ide_dma_start,
+ .dma_end = sc1200_dma_end,
+ .dma_test_irq = ide_dma_test_irq,
+ .dma_lost_irq = ide_dma_lost_irq,
+ .dma_timeout = ide_dma_timeout,
+};
static const struct ide_port_info sc1200_chipset __devinitdata = {
.name = "SC1200",
- .init_hwif = init_hwif_sc1200,
+ .port_ops = &sc1200_port_ops,
+ .dma_ops = &sc1200_dma_ops,
.host_flags = IDE_HFLAG_SERIALIZE |
IDE_HFLAG_POST_SET_MODE |
IDE_HFLAG_ABUSE_DMA_MODES,
diff --git a/drivers/ide/pci/scc_pata.c b/drivers/ide/pci/scc_pata.c
index 5214579..17cf864 100644
--- a/drivers/ide/pci/scc_pata.c
+++ b/drivers/ide/pci/scc_pata.c
@@ -317,14 +317,14 @@
/**
- * scc_ide_dma_end - Stop DMA
+ * scc_dma_end - Stop DMA
* @drive: IDE drive
*
* Check and clear INT Status register.
* Then call __ide_dma_end().
*/
-static int scc_ide_dma_end(ide_drive_t * drive)
+static int scc_dma_end(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
unsigned long intsts_port = hwif->dma_base + 0x014;
@@ -449,7 +449,7 @@
if (!drive->waiting_for_dma)
printk(KERN_WARNING "%s: (%s) called while not waiting\n",
- drive->name, __FUNCTION__);
+ drive->name, __func__);
return 0;
}
@@ -483,7 +483,7 @@
unsigned long dma_size = pci_resource_len(dev, 1);
void __iomem *ctl_addr;
void __iomem *dma_addr;
- int i;
+ int i, ret;
for (i = 0; i < MAX_HWIFS; i++) {
if (scc_ports[i].ctl == 0)
@@ -492,21 +492,17 @@
if (i >= MAX_HWIFS)
return -ENOMEM;
- if (!request_mem_region(ctl_base, ctl_size, name)) {
- printk(KERN_WARNING "%s: IDE controller MMIO ports not available.\n", SCC_PATA_NAME);
- goto fail_0;
- }
-
- if (!request_mem_region(dma_base, dma_size, name)) {
- printk(KERN_WARNING "%s: IDE controller MMIO ports not available.\n", SCC_PATA_NAME);
- goto fail_1;
+ ret = pci_request_selected_regions(dev, (1 << 2) - 1, name);
+ if (ret < 0) {
+ printk(KERN_ERR "%s: can't reserve resources\n", name);
+ return ret;
}
if ((ctl_addr = ioremap(ctl_base, ctl_size)) == NULL)
- goto fail_2;
+ goto fail_0;
if ((dma_addr = ioremap(dma_base, dma_size)) == NULL)
- goto fail_3;
+ goto fail_1;
pci_set_master(dev);
scc_ports[i].ctl = (unsigned long)ctl_addr;
@@ -515,12 +511,8 @@
return 1;
- fail_3:
- iounmap(ctl_addr);
- fail_2:
- release_mem_region(dma_base, dma_size);
fail_1:
- release_mem_region(ctl_base, ctl_size);
+ iounmap(ctl_addr);
fail_0:
return -ENOMEM;
}
@@ -549,7 +541,6 @@
hw.chipset = ide_pci;
ide_init_port_hw(hwif, &hw);
hwif->dev = &dev->dev;
- hwif->cds = d;
idx[0] = hwif->index;
@@ -701,26 +692,37 @@
/* PTERADD */
out_be32((void __iomem *)(hwif->dma_base + 0x018), hwif->dmatable_dma);
- hwif->dma_setup = scc_dma_setup;
- hwif->ide_dma_end = scc_ide_dma_end;
- hwif->set_pio_mode = scc_set_pio_mode;
- hwif->set_dma_mode = scc_set_dma_mode;
- hwif->ide_dma_test_irq = scc_dma_test_irq;
- hwif->udma_filter = scc_udma_filter;
-
if (in_be32((void __iomem *)(hwif->config_data + 0xff0)) & CCKCTRL_ATACLKOEN)
hwif->ultra_mask = ATA_UDMA6; /* 133MHz */
else
hwif->ultra_mask = ATA_UDMA5; /* 100MHz */
-
- hwif->cable_detect = scc_cable_detect;
}
+static const struct ide_port_ops scc_port_ops = {
+ .set_pio_mode = scc_set_pio_mode,
+ .set_dma_mode = scc_set_dma_mode,
+ .udma_filter = scc_udma_filter,
+ .cable_detect = scc_cable_detect,
+};
+
+static const struct ide_dma_ops scc_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = scc_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = ide_dma_start,
+ .dma_end = scc_dma_end,
+ .dma_test_irq = scc_dma_test_irq,
+ .dma_lost_irq = ide_dma_lost_irq,
+ .dma_timeout = ide_dma_timeout,
+};
+
#define DECLARE_SCC_DEV(name_str) \
{ \
.name = name_str, \
.init_iops = init_iops_scc, \
.init_hwif = init_hwif_scc, \
+ .port_ops = &scc_port_ops, \
+ .dma_ops = &scc_dma_ops, \
.host_flags = IDE_HFLAG_SINGLE, \
.pio_mask = ATA_PIO4, \
}
@@ -754,10 +756,6 @@
{
struct scc_ports *ports = pci_get_drvdata(dev);
ide_hwif_t *hwif = ports->hwif;
- unsigned long ctl_base = pci_resource_start(dev, 0);
- unsigned long dma_base = pci_resource_start(dev, 1);
- unsigned long ctl_size = pci_resource_len(dev, 0);
- unsigned long dma_size = pci_resource_len(dev, 1);
if (hwif->dmatable_cpu) {
pci_free_consistent(dev, PRD_ENTRIES * PRD_BYTES,
@@ -770,8 +768,7 @@
hwif->chipset = ide_unknown;
iounmap((void*)ports->dma);
iounmap((void*)ports->ctl);
- release_mem_region(dma_base, dma_size);
- release_mem_region(ctl_base, ctl_size);
+ pci_release_selected_regions(dev, (1 << 2) - 1);
memset(ports, 0, sizeof(*ports));
}
diff --git a/drivers/ide/pci/serverworks.c b/drivers/ide/pci/serverworks.c
index cfe9274..a1fb208 100644
--- a/drivers/ide/pci/serverworks.c
+++ b/drivers/ide/pci/serverworks.c
@@ -312,7 +312,7 @@
return ATA_CBL_PATA40;
}
-static u8 __devinit ata66_svwks(ide_hwif_t *hwif)
+static u8 __devinit svwks_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
@@ -336,17 +336,18 @@
return ATA_CBL_PATA40;
}
-static void __devinit init_hwif_svwks (ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
+static const struct ide_port_ops osb4_port_ops = {
+ .set_pio_mode = svwks_set_pio_mode,
+ .set_dma_mode = svwks_set_dma_mode,
+ .udma_filter = svwks_udma_filter,
+};
- hwif->set_pio_mode = &svwks_set_pio_mode;
- hwif->set_dma_mode = &svwks_set_dma_mode;
- hwif->udma_filter = &svwks_udma_filter;
-
- if (dev->device != PCI_DEVICE_ID_SERVERWORKS_OSB4IDE)
- hwif->cable_detect = ata66_svwks;
-}
+static const struct ide_port_ops svwks_port_ops = {
+ .set_pio_mode = svwks_set_pio_mode,
+ .set_dma_mode = svwks_set_dma_mode,
+ .udma_filter = svwks_udma_filter,
+ .cable_detect = svwks_cable_detect,
+};
#define IDE_HFLAGS_SVWKS \
(IDE_HFLAG_LEGACY_IRQS | \
@@ -356,7 +357,7 @@
{ /* 0 */
.name = "SvrWks OSB4",
.init_chipset = init_chipset_svwks,
- .init_hwif = init_hwif_svwks,
+ .port_ops = &osb4_port_ops,
.host_flags = IDE_HFLAGS_SVWKS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
@@ -364,7 +365,7 @@
},{ /* 1 */
.name = "SvrWks CSB5",
.init_chipset = init_chipset_svwks,
- .init_hwif = init_hwif_svwks,
+ .port_ops = &svwks_port_ops,
.host_flags = IDE_HFLAGS_SVWKS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
@@ -372,7 +373,7 @@
},{ /* 2 */
.name = "SvrWks CSB6",
.init_chipset = init_chipset_svwks,
- .init_hwif = init_hwif_svwks,
+ .port_ops = &svwks_port_ops,
.host_flags = IDE_HFLAGS_SVWKS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
@@ -380,7 +381,7 @@
},{ /* 3 */
.name = "SvrWks CSB6",
.init_chipset = init_chipset_svwks,
- .init_hwif = init_hwif_svwks,
+ .port_ops = &svwks_port_ops,
.host_flags = IDE_HFLAGS_SVWKS | IDE_HFLAG_SINGLE,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
@@ -388,7 +389,7 @@
},{ /* 4 */
.name = "SvrWks HT1000",
.init_chipset = init_chipset_svwks,
- .init_hwif = init_hwif_svwks,
+ .port_ops = &svwks_port_ops,
.host_flags = IDE_HFLAGS_SVWKS | IDE_HFLAG_SINGLE,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
diff --git a/drivers/ide/pci/sgiioc4.c b/drivers/ide/pci/sgiioc4.c
index 6bd9523..321a4e2 100644
--- a/drivers/ide/pci/sgiioc4.c
+++ b/drivers/ide/pci/sgiioc4.c
@@ -170,10 +170,10 @@
printk(KERN_ERR
"%s(%s) : PCI Bus Error when doing DMA:"
" status-cmd reg is 0x%x\n",
- __FUNCTION__, drive->name, pci_stat_cmd_reg);
+ __func__, drive->name, pci_stat_cmd_reg);
printk(KERN_ERR
"%s(%s) : PCI Error Address is 0x%x%x\n",
- __FUNCTION__, drive->name,
+ __func__, drive->name,
pci_err_addr_high, pci_err_addr_low);
/* Clear the PCI Error indicator */
pci_write_config_dword(dev, PCI_COMMAND, 0x00000146);
@@ -188,7 +188,7 @@
return intr_reg & 3;
}
-static void sgiioc4_ide_dma_start(ide_drive_t * drive)
+static void sgiioc4_dma_start(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
unsigned long ioc4_dma_addr = hwif->dma_base + IOC4_DMA_CTRL * 4;
@@ -215,8 +215,7 @@
}
/* Stops the IOC4 DMA Engine */
-static int
-sgiioc4_ide_dma_end(ide_drive_t * drive)
+static int sgiioc4_dma_end(ide_drive_t *drive)
{
u32 ioc4_dma, bc_dev, bc_mem, num, valid = 0, cnt = 0;
ide_hwif_t *hwif = HWIF(drive);
@@ -232,7 +231,7 @@
printk(KERN_ERR
"%s(%s): IOC4 DMA STOP bit is still 1 :"
"ioc4_dma_reg 0x%x\n",
- __FUNCTION__, drive->name, ioc4_dma);
+ __func__, drive->name, ioc4_dma);
dma_stat = 1;
}
@@ -251,7 +250,7 @@
udelay(1);
}
if (!valid) {
- printk(KERN_ERR "%s(%s) : DMA incomplete\n", __FUNCTION__,
+ printk(KERN_ERR "%s(%s) : DMA incomplete\n", __func__,
drive->name);
dma_stat = 1;
}
@@ -264,7 +263,7 @@
printk(KERN_ERR
"%s(%s): WARNING!! byte_count_dev %d "
"!= byte_count_mem %d\n",
- __FUNCTION__, drive->name, bc_dev, bc_mem);
+ __func__, drive->name, bc_dev, bc_mem);
}
}
@@ -279,8 +278,7 @@
}
/* returns 1 if dma irq issued, 0 otherwise */
-static int
-sgiioc4_ide_dma_test_irq(ide_drive_t * drive)
+static int sgiioc4_dma_test_irq(ide_drive_t *drive)
{
return sgiioc4_checkirq(HWIF(drive));
}
@@ -294,7 +292,7 @@
static void
sgiioc4_resetproc(ide_drive_t * drive)
{
- sgiioc4_ide_dma_end(drive);
+ sgiioc4_dma_end(drive);
sgiioc4_clearirq(drive);
}
@@ -329,13 +327,17 @@
/* Creates a dma map for the scatter-gather list entries */
static int __devinit
-ide_dma_sgiioc4(ide_hwif_t * hwif, unsigned long dma_base)
+ide_dma_sgiioc4(ide_hwif_t *hwif, const struct ide_port_info *d)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
+ unsigned long dma_base = pci_resource_start(dev, 0) + IOC4_DMA_OFFSET;
void __iomem *virt_dma_base;
int num_ports = sizeof (ioc4_dma_regs_t);
void *pad;
+ if (dma_base == 0)
+ return -1;
+
printk(KERN_INFO "%s: BM-DMA at 0x%04lx-0x%04lx\n", hwif->name,
dma_base, dma_base + num_ports - 1);
@@ -343,7 +345,7 @@
printk(KERN_ERR
"%s(%s) -- ERROR, Addresses 0x%p to 0x%p "
"ALREADY in use\n",
- __FUNCTION__, hwif->name, (void *) dma_base,
+ __func__, hwif->name, (void *) dma_base,
(void *) dma_base + num_ports - 1);
return -1;
}
@@ -352,7 +354,7 @@
if (virt_dma_base == NULL) {
printk(KERN_ERR
"%s(%s) -- ERROR, Unable to map addresses 0x%lx to 0x%lx\n",
- __FUNCTION__, hwif->name, dma_base, dma_base + num_ports - 1);
+ __func__, hwif->name, dma_base, dma_base + num_ports - 1);
goto dma_remap_failure;
}
hwif->dma_base = (unsigned long) virt_dma_base;
@@ -378,7 +380,7 @@
hwif->dmatable_cpu, hwif->dmatable_dma);
printk(KERN_INFO
"%s() -- Error! Unable to allocate DMA Maps for drive %s\n",
- __FUNCTION__, hwif->name);
+ __func__, hwif->name);
printk(KERN_INFO
"Changing from DMA to PIO mode for Drive %s\n", hwif->name);
@@ -406,14 +408,14 @@
if (ioc4_dma & IOC4_S_DMA_ACTIVE) {
printk(KERN_WARNING
"%s(%s):Warning!! DMA from previous transfer was still active\n",
- __FUNCTION__, drive->name);
+ __func__, drive->name);
writel(IOC4_S_DMA_STOP, (void __iomem *)ioc4_dma_addr);
ioc4_dma = sgiioc4_ide_dma_stop(hwif, dma_base);
if (ioc4_dma & IOC4_S_DMA_STOP)
printk(KERN_ERR
"%s(%s) : IOC4 Dma STOP bit is still 1\n",
- __FUNCTION__, drive->name);
+ __func__, drive->name);
}
ioc4_dma = readl((void __iomem *)ioc4_dma_addr);
@@ -421,14 +423,14 @@
printk(KERN_WARNING
"%s(%s) : Warning!! - DMA Error during Previous"
" transfer | status 0x%x\n",
- __FUNCTION__, drive->name, ioc4_dma);
+ __func__, drive->name, ioc4_dma);
writel(IOC4_S_DMA_STOP, (void __iomem *)ioc4_dma_addr);
ioc4_dma = sgiioc4_ide_dma_stop(hwif, dma_base);
if (ioc4_dma & IOC4_S_DMA_STOP)
printk(KERN_ERR
"%s(%s) : IOC4 DMA STOP bit is still 1\n",
- __FUNCTION__, drive->name);
+ __func__, drive->name);
}
/* Address of the Scatter Gather List */
@@ -519,7 +521,7 @@
return 0; /* revert to PIO for this request */
}
-static int sgiioc4_ide_dma_setup(ide_drive_t *drive)
+static int sgiioc4_dma_setup(ide_drive_t *drive)
{
struct request *rq = HWGROUP(drive)->rq;
unsigned int count = 0;
@@ -548,45 +550,37 @@
return 0;
}
-static void __devinit
-ide_init_sgiioc4(ide_hwif_t * hwif)
-{
- hwif->mmio = 1;
- hwif->set_pio_mode = NULL; /* Sets timing for PIO mode */
- hwif->set_dma_mode = &sgiioc4_set_dma_mode;
- hwif->selectproc = NULL;/* Use the default routine to select drive */
- hwif->reset_poll = NULL;/* No HBA specific reset_poll needed */
- hwif->pre_reset = NULL; /* No HBA specific pre_set needed */
- hwif->resetproc = &sgiioc4_resetproc;/* Reset DMA engine,
- clear interrupts */
- hwif->maskproc = &sgiioc4_maskproc; /* Mask on/off NIEN register */
- hwif->quirkproc = NULL;
+static const struct ide_port_ops sgiioc4_port_ops = {
+ .set_dma_mode = sgiioc4_set_dma_mode,
+ /* reset DMA engine, clear IRQs */
+ .resetproc = sgiioc4_resetproc,
+ /* mask on/off NIEN register */
+ .maskproc = sgiioc4_maskproc,
+};
- hwif->INB = &sgiioc4_INB;
-
- if (hwif->dma_base == 0)
- return;
-
- hwif->dma_host_set = &sgiioc4_dma_host_set;
- hwif->dma_setup = &sgiioc4_ide_dma_setup;
- hwif->dma_start = &sgiioc4_ide_dma_start;
- hwif->ide_dma_end = &sgiioc4_ide_dma_end;
- hwif->ide_dma_test_irq = &sgiioc4_ide_dma_test_irq;
- hwif->dma_lost_irq = &sgiioc4_dma_lost_irq;
- hwif->dma_timeout = &ide_dma_timeout;
-}
+static const struct ide_dma_ops sgiioc4_dma_ops = {
+ .dma_host_set = sgiioc4_dma_host_set,
+ .dma_setup = sgiioc4_dma_setup,
+ .dma_start = sgiioc4_dma_start,
+ .dma_end = sgiioc4_dma_end,
+ .dma_test_irq = sgiioc4_dma_test_irq,
+ .dma_lost_irq = sgiioc4_dma_lost_irq,
+ .dma_timeout = ide_dma_timeout,
+};
static const struct ide_port_info sgiioc4_port_info __devinitdata = {
.chipset = ide_pci,
- .host_flags = IDE_HFLAG_NO_DMA | /* no SFF-style DMA */
- IDE_HFLAG_NO_AUTOTUNE,
+ .init_dma = ide_dma_sgiioc4,
+ .port_ops = &sgiioc4_port_ops,
+ .dma_ops = &sgiioc4_dma_ops,
+ .host_flags = IDE_HFLAG_NO_AUTOTUNE,
.mwdma_mask = ATA_MWDMA2_ONLY,
};
static int __devinit
sgiioc4_ide_setup_pci_device(struct pci_dev *dev)
{
- unsigned long cmd_base, dma_base, irqport;
+ unsigned long cmd_base, irqport;
unsigned long bar0, cmd_phys_base, ctl;
void __iomem *virt_base;
ide_hwif_t *hwif;
@@ -612,7 +606,6 @@
cmd_base = (unsigned long) virt_base + IOC4_CMD_OFFSET;
ctl = (unsigned long) virt_base + IOC4_CTRL_OFFSET;
irqport = (unsigned long) virt_base + IOC4_INTR_OFFSET;
- dma_base = pci_resource_start(dev, 0) + IOC4_DMA_OFFSET;
cmd_phys_base = bar0 + IOC4_CMD_OFFSET;
if (!request_mem_region(cmd_phys_base, IOC4_CMD_CTL_BLK_SIZE,
@@ -620,7 +613,7 @@
printk(KERN_ERR
"%s : %s -- ERROR, Addresses "
"0x%p to 0x%p ALREADY in use\n",
- __FUNCTION__, hwif->name, (void *) cmd_phys_base,
+ __func__, hwif->name, (void *) cmd_phys_base,
(void *) cmd_phys_base + IOC4_CMD_CTL_BLK_SIZE);
return -ENOMEM;
}
@@ -641,13 +634,7 @@
/* Initializing chipset IRQ Registers */
writel(0x03, (void __iomem *)(irqport + IOC4_INTR_SET * 4));
- if (dma_base == 0 || ide_dma_sgiioc4(hwif, dma_base)) {
- printk(KERN_INFO "%s: %s Bus-Master DMA disabled\n",
- hwif->name, DRV_NAME);
- d.mwdma_mask = 0;
- }
-
- ide_init_sgiioc4(hwif);
+ hwif->INB = &sgiioc4_INB;
idx[0] = hwif->index;
diff --git a/drivers/ide/pci/siimage.c b/drivers/ide/pci/siimage.c
index c9ecab8..1fffea3 100644
--- a/drivers/ide/pci/siimage.c
+++ b/drivers/ide/pci/siimage.c
@@ -301,7 +301,7 @@
}
/* returns 1 if dma irq issued, 0 otherwise */
-static int siimage_io_ide_dma_test_irq (ide_drive_t *drive)
+static int siimage_io_dma_test_irq(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = to_pci_dev(hwif->dev);
@@ -320,14 +320,14 @@
}
/**
- * siimage_mmio_ide_dma_test_irq - check we caused an IRQ
+ * siimage_mmio_dma_test_irq - check we caused an IRQ
* @drive: drive we are testing
*
* Check if we caused an IDE DMA interrupt. We may also have caused
* SATA status interrupts, if so we clean them up and continue.
*/
-
-static int siimage_mmio_ide_dma_test_irq (ide_drive_t *drive)
+
+static int siimage_mmio_dma_test_irq(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
unsigned long addr = siimage_selreg(hwif, 0x1);
@@ -347,7 +347,7 @@
printk(KERN_WARNING "%s: sata_error = 0x%08x, "
"watchdog = %d, %s\n",
drive->name, sata_error, watchdog,
- __FUNCTION__);
+ __func__);
} else {
watchdog = (ext_stat & 0x8000) ? 1 : 0;
@@ -369,6 +369,14 @@
return 0;
}
+static int siimage_dma_test_irq(ide_drive_t *drive)
+{
+ if (drive->hwif->mmio)
+ return siimage_mmio_dma_test_irq(drive);
+ else
+ return siimage_io_dma_test_irq(drive);
+}
+
/**
* sil_sata_reset_poll - wait for SATA reset
* @drive: drive we are resetting
@@ -735,14 +743,14 @@
}
/**
- * ata66_siimage - check for 80 pin cable
+ * sil_cable_detect - cable detection
* @hwif: interface to check
*
* Check for the presence of an ATA66 capable cable on the
* interface.
*/
-static u8 __devinit ata66_siimage(ide_hwif_t *hwif)
+static u8 __devinit sil_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
unsigned long addr = siimage_selreg(hwif, 0);
@@ -756,67 +764,44 @@
return (ata66 & 0x01) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
}
-/**
- * init_hwif_siimage - set up hwif structs
- * @hwif: interface to set up
- *
- * We do the basic set up of the interface structure. The SIIMAGE
- * requires several custom handlers so we override the default
- * ide DMA handlers appropriately
- */
+static const struct ide_port_ops sil_pata_port_ops = {
+ .set_pio_mode = sil_set_pio_mode,
+ .set_dma_mode = sil_set_dma_mode,
+ .quirkproc = sil_quirkproc,
+ .udma_filter = sil_pata_udma_filter,
+ .cable_detect = sil_cable_detect,
+};
-static void __devinit init_hwif_siimage(ide_hwif_t *hwif)
-{
- u8 sata = is_sata(hwif);
+static const struct ide_port_ops sil_sata_port_ops = {
+ .set_pio_mode = sil_set_pio_mode,
+ .set_dma_mode = sil_set_dma_mode,
+ .reset_poll = sil_sata_reset_poll,
+ .pre_reset = sil_sata_pre_reset,
+ .quirkproc = sil_quirkproc,
+ .udma_filter = sil_sata_udma_filter,
+ .cable_detect = sil_cable_detect,
+};
- hwif->set_pio_mode = &sil_set_pio_mode;
- hwif->set_dma_mode = &sil_set_dma_mode;
- hwif->quirkproc = &sil_quirkproc;
+static struct ide_dma_ops sil_dma_ops = {
+ .dma_test_irq = siimage_dma_test_irq,
+};
- if (sata) {
- static int first = 1;
-
- hwif->reset_poll = &sil_sata_reset_poll;
- hwif->pre_reset = &sil_sata_pre_reset;
- hwif->udma_filter = &sil_sata_udma_filter;
-
- if (first) {
- printk(KERN_INFO "siimage: For full SATA support you should use the libata sata_sil module.\n");
- first = 0;
- }
- } else
- hwif->udma_filter = &sil_pata_udma_filter;
-
- hwif->cable_detect = ata66_siimage;
-
- if (hwif->dma_base == 0)
- return;
-
- if (sata)
- hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
-
- if (hwif->mmio) {
- hwif->ide_dma_test_irq = &siimage_mmio_ide_dma_test_irq;
- } else {
- hwif->ide_dma_test_irq = & siimage_io_ide_dma_test_irq;
- }
-}
-
-#define DECLARE_SII_DEV(name_str) \
+#define DECLARE_SII_DEV(name_str, p_ops) \
{ \
.name = name_str, \
.init_chipset = init_chipset_siimage, \
.init_iops = init_iops_siimage, \
- .init_hwif = init_hwif_siimage, \
+ .port_ops = p_ops, \
+ .dma_ops = &sil_dma_ops, \
.pio_mask = ATA_PIO4, \
.mwdma_mask = ATA_MWDMA2, \
.udma_mask = ATA_UDMA6, \
}
static const struct ide_port_info siimage_chipsets[] __devinitdata = {
- /* 0 */ DECLARE_SII_DEV("SiI680"),
- /* 1 */ DECLARE_SII_DEV("SiI3112 Serial ATA"),
- /* 2 */ DECLARE_SII_DEV("Adaptec AAR-1210SA")
+ /* 0 */ DECLARE_SII_DEV("SiI680", &sil_pata_port_ops),
+ /* 1 */ DECLARE_SII_DEV("SiI3112 Serial ATA", &sil_sata_port_ops),
+ /* 2 */ DECLARE_SII_DEV("Adaptec AAR-1210SA", &sil_sata_port_ops)
};
/**
@@ -830,7 +815,24 @@
static int __devinit siimage_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- return ide_setup_pci_device(dev, &siimage_chipsets[id->driver_data]);
+ struct ide_port_info d;
+ u8 idx = id->driver_data;
+
+ d = siimage_chipsets[idx];
+
+ if (idx) {
+ static int first = 1;
+
+ if (first) {
+ printk(KERN_INFO "siimage: For full SATA support you "
+ "should use the libata sata_sil module.\n");
+ first = 0;
+ }
+
+ d.host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
+ }
+
+ return ide_setup_pci_device(dev, &d);
}
static const struct pci_device_id siimage_pci_tbl[] = {
diff --git a/drivers/ide/pci/sis5513.c b/drivers/ide/pci/sis5513.c
index 181b647..4b0b85d 100644
--- a/drivers/ide/pci/sis5513.c
+++ b/drivers/ide/pci/sis5513.c
@@ -347,7 +347,7 @@
sis_program_timings(drive, speed);
}
-static u8 sis5513_ata133_udma_filter(ide_drive_t *drive)
+static u8 sis_ata133_udma_filter(ide_drive_t *drive)
{
struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
u32 regdw = 0;
@@ -514,7 +514,7 @@
{ 0, }
};
-static u8 __devinit ata66_sis5513(ide_hwif_t *hwif)
+static u8 __devinit sis_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *pdev = to_pci_dev(hwif->dev);
const struct sis_laptop *lap = &sis_laptop[0];
@@ -543,21 +543,22 @@
return ata66 ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
}
-static void __devinit init_hwif_sis5513(ide_hwif_t *hwif)
-{
- hwif->set_pio_mode = &sis_set_pio_mode;
- hwif->set_dma_mode = &sis_set_dma_mode;
+static const struct ide_port_ops sis_port_ops = {
+ .set_pio_mode = sis_set_pio_mode,
+ .set_dma_mode = sis_set_dma_mode,
+ .cable_detect = sis_cable_detect,
+};
- if (chipset_family >= ATA_133)
- hwif->udma_filter = sis5513_ata133_udma_filter;
-
- hwif->cable_detect = ata66_sis5513;
-}
+static const struct ide_port_ops sis_ata133_port_ops = {
+ .set_pio_mode = sis_set_pio_mode,
+ .set_dma_mode = sis_set_dma_mode,
+ .udma_filter = sis_ata133_udma_filter,
+ .cable_detect = sis_cable_detect,
+};
static const struct ide_port_info sis5513_chipset __devinitdata = {
.name = "SIS5513",
.init_chipset = init_chipset_sis5513,
- .init_hwif = init_hwif_sis5513,
.enablebits = { {0x4a, 0x02, 0x02}, {0x4a, 0x04, 0x04} },
.host_flags = IDE_HFLAG_LEGACY_IRQS | IDE_HFLAG_NO_AUTODMA,
.pio_mask = ATA_PIO4,
@@ -572,6 +573,11 @@
if (sis_find_family(dev) == 0)
return -ENOTSUPP;
+ if (chipset_family >= ATA_133)
+ d.port_ops = &sis_ata133_port_ops;
+ else
+ d.port_ops = &sis_port_ops;
+
d.udma_mask = udma_rates[chipset_family];
return ide_setup_pci_device(dev, &d);
diff --git a/drivers/ide/pci/sl82c105.c b/drivers/ide/pci/sl82c105.c
index 40b3eeb..ce84fa0 100644
--- a/drivers/ide/pci/sl82c105.c
+++ b/drivers/ide/pci/sl82c105.c
@@ -179,7 +179,7 @@
struct pci_dev *dev = to_pci_dev(hwif->dev);
int reg = 0x44 + drive->dn * 4;
- DBG(("%s(drive:%s)\n", __FUNCTION__, drive->name));
+ DBG(("%s(drive:%s)\n", __func__, drive->name));
pci_write_config_word(dev, reg, drive->drive_data >> 16);
@@ -203,7 +203,7 @@
int reg = 0x44 + drive->dn * 4;
int ret;
- DBG(("%s(drive:%s)\n", __FUNCTION__, drive->name));
+ DBG(("%s(drive:%s)\n", __func__, drive->name));
ret = __ide_dma_end(drive);
@@ -232,7 +232,7 @@
* Return the revision of the Winbond bridge
* which this function is part of.
*/
-static unsigned int sl82c105_bridge_revision(struct pci_dev *dev)
+static u8 sl82c105_bridge_revision(struct pci_dev *dev)
{
struct pci_dev *bridge;
@@ -282,63 +282,59 @@
return dev->irq;
}
-/*
- * Initialise IDE channel
- */
-static void __devinit init_hwif_sl82c105(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- unsigned int rev;
+static const struct ide_port_ops sl82c105_port_ops = {
+ .set_pio_mode = sl82c105_set_pio_mode,
+ .set_dma_mode = sl82c105_set_dma_mode,
+ .resetproc = sl82c105_resetproc,
+};
- DBG(("init_hwif_sl82c105(hwif: ide%d)\n", hwif->index));
-
- hwif->set_pio_mode = &sl82c105_set_pio_mode;
- hwif->set_dma_mode = &sl82c105_set_dma_mode;
- hwif->resetproc = &sl82c105_resetproc;
-
- if (!hwif->dma_base)
- return;
-
- rev = sl82c105_bridge_revision(dev);
- if (rev <= 5) {
- /*
- * Never ever EVER under any circumstances enable
- * DMA when the bridge is this old.
- */
- printk(" %s: Winbond W83C553 bridge revision %d, "
- "BM-DMA disabled\n", hwif->name, rev);
- return;
- }
-
- hwif->mwdma_mask = ATA_MWDMA2;
-
- hwif->dma_lost_irq = &sl82c105_dma_lost_irq;
- hwif->dma_start = &sl82c105_dma_start;
- hwif->ide_dma_end = &sl82c105_dma_end;
- hwif->dma_timeout = &sl82c105_dma_timeout;
-
- if (hwif->mate)
- hwif->serialized = hwif->mate->serialized = 1;
-}
+static const struct ide_dma_ops sl82c105_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ide_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = sl82c105_dma_start,
+ .dma_end = sl82c105_dma_end,
+ .dma_test_irq = ide_dma_test_irq,
+ .dma_lost_irq = sl82c105_dma_lost_irq,
+ .dma_timeout = sl82c105_dma_timeout,
+};
static const struct ide_port_info sl82c105_chipset __devinitdata = {
.name = "W82C105",
.init_chipset = init_chipset_sl82c105,
- .init_hwif = init_hwif_sl82c105,
.enablebits = {{0x40,0x01,0x01}, {0x40,0x10,0x10}},
+ .port_ops = &sl82c105_port_ops,
+ .dma_ops = &sl82c105_dma_ops,
.host_flags = IDE_HFLAG_IO_32BIT |
IDE_HFLAG_UNMASK_IRQS |
/* FIXME: check for Compatibility mode in generic IDE PCI code */
#if defined(CONFIG_LOPEC) || defined(CONFIG_SANDPOINT)
IDE_HFLAG_FORCE_LEGACY_IRQS |
#endif
+ IDE_HFLAG_SERIALIZE_DMA |
IDE_HFLAG_NO_AUTODMA,
.pio_mask = ATA_PIO5,
+ .mwdma_mask = ATA_MWDMA2,
};
static int __devinit sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- return ide_setup_pci_device(dev, &sl82c105_chipset);
+ struct ide_port_info d = sl82c105_chipset;
+ u8 rev = sl82c105_bridge_revision(dev);
+
+ if (rev <= 5) {
+ /*
+ * Never ever EVER under any circumstances enable
+ * DMA when the bridge is this old.
+ */
+ printk(KERN_INFO "W82C105_IDE: Winbond W83C553 bridge "
+ "revision %d, BM-DMA disabled\n", rev);
+ d.dma_ops = NULL;
+ d.mwdma_mask = 0;
+ d.host_flags &= ~IDE_HFLAG_SERIALIZE_DMA;
+ }
+
+ return ide_setup_pci_device(dev, &d);
}
static const struct pci_device_id sl82c105_pci_tbl[] = {
diff --git a/drivers/ide/pci/slc90e66.c b/drivers/ide/pci/slc90e66.c
index eab557c..dae6e2c 100644
--- a/drivers/ide/pci/slc90e66.c
+++ b/drivers/ide/pci/slc90e66.c
@@ -125,18 +125,16 @@
return (reg47 & mask) ? ATA_CBL_PATA40 : ATA_CBL_PATA80;
}
-static void __devinit init_hwif_slc90e66(ide_hwif_t *hwif)
-{
- hwif->set_pio_mode = &slc90e66_set_pio_mode;
- hwif->set_dma_mode = &slc90e66_set_dma_mode;
-
- hwif->cable_detect = slc90e66_cable_detect;
-}
+static const struct ide_port_ops slc90e66_port_ops = {
+ .set_pio_mode = slc90e66_set_pio_mode,
+ .set_dma_mode = slc90e66_set_dma_mode,
+ .cable_detect = slc90e66_cable_detect,
+};
static const struct ide_port_info slc90e66_chipset __devinitdata = {
.name = "SLC90E66",
- .init_hwif = init_hwif_slc90e66,
.enablebits = { {0x41, 0x80, 0x80}, {0x43, 0x80, 0x80} },
+ .port_ops = &slc90e66_port_ops,
.host_flags = IDE_HFLAG_LEGACY_IRQS,
.pio_mask = ATA_PIO4,
.swdma_mask = ATA_SWDMA2_ONLY,
diff --git a/drivers/ide/pci/tc86c001.c b/drivers/ide/pci/tc86c001.c
index c154351..9b4b27a 100644
--- a/drivers/ide/pci/tc86c001.c
+++ b/drivers/ide/pci/tc86c001.c
@@ -157,11 +157,6 @@
/* Store the system control register base for convenience... */
hwif->config_data = sc_base;
- hwif->set_pio_mode = &tc86c001_set_pio_mode;
- hwif->set_dma_mode = &tc86c001_set_mode;
-
- hwif->cable_detect = tc86c001_cable_detect;
-
if (!hwif->dma_base)
return;
@@ -173,8 +168,6 @@
/* Sector Count Register limit */
hwif->rqsize = 0xffff;
-
- hwif->dma_start = &tc86c001_dma_start;
}
static unsigned int __devinit init_chipset_tc86c001(struct pci_dev *dev,
@@ -187,10 +180,29 @@
return err;
}
+static const struct ide_port_ops tc86c001_port_ops = {
+ .set_pio_mode = tc86c001_set_pio_mode,
+ .set_dma_mode = tc86c001_set_mode,
+ .cable_detect = tc86c001_cable_detect,
+};
+
+static const struct ide_dma_ops tc86c001_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ide_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = tc86c001_dma_start,
+ .dma_end = __ide_dma_end,
+ .dma_test_irq = ide_dma_test_irq,
+ .dma_lost_irq = ide_dma_lost_irq,
+ .dma_timeout = ide_dma_timeout,
+};
+
static const struct ide_port_info tc86c001_chipset __devinitdata = {
.name = "TC86C001",
.init_chipset = init_chipset_tc86c001,
.init_hwif = init_hwif_tc86c001,
+ .port_ops = &tc86c001_port_ops,
+ .dma_ops = &tc86c001_dma_ops,
.host_flags = IDE_HFLAG_SINGLE | IDE_HFLAG_OFF_BOARD |
IDE_HFLAG_ABUSE_SET_DMA_MODE,
.pio_mask = ATA_PIO4,
diff --git a/drivers/ide/pci/triflex.c b/drivers/ide/pci/triflex.c
index 3316b19..db65a55 100644
--- a/drivers/ide/pci/triflex.c
+++ b/drivers/ide/pci/triflex.c
@@ -87,16 +87,15 @@
triflex_set_mode(drive, XFER_PIO_0 + pio);
}
-static void __devinit init_hwif_triflex(ide_hwif_t *hwif)
-{
- hwif->set_pio_mode = &triflex_set_pio_mode;
- hwif->set_dma_mode = &triflex_set_mode;
-}
+static const struct ide_port_ops triflex_port_ops = {
+ .set_pio_mode = triflex_set_pio_mode,
+ .set_dma_mode = triflex_set_mode,
+};
static const struct ide_port_info triflex_device __devinitdata = {
.name = "TRIFLEX",
- .init_hwif = init_hwif_triflex,
.enablebits = {{0x80, 0x01, 0x01}, {0x80, 0x02, 0x02}},
+ .port_ops = &triflex_port_ops,
.pio_mask = ATA_PIO4,
.swdma_mask = ATA_SWDMA2,
.mwdma_mask = ATA_MWDMA2,
diff --git a/drivers/ide/pci/trm290.c b/drivers/ide/pci/trm290.c
index 2b8f3a2..15ee38f 100644
--- a/drivers/ide/pci/trm290.c
+++ b/drivers/ide/pci/trm290.c
@@ -214,7 +214,7 @@
{
}
-static int trm290_ide_dma_end (ide_drive_t *drive)
+static int trm290_dma_end(ide_drive_t *drive)
{
u16 status;
@@ -225,7 +225,7 @@
return status != 0x00ff;
}
-static int trm290_ide_dma_test_irq (ide_drive_t *drive)
+static int trm290_dma_test_irq(ide_drive_t *drive)
{
u16 status;
@@ -254,22 +254,11 @@
hwif->config_data = cfg_base;
hwif->dma_base = (cfg_base + 4) ^ (hwif->channel ? 0x80 : 0);
- printk(KERN_INFO " %s: BM-DMA at 0x%04lx-0x%04lx",
+ printk(KERN_INFO " %s: BM-DMA at 0x%04lx-0x%04lx\n",
hwif->name, hwif->dma_base, hwif->dma_base + 3);
- if (!request_region(hwif->dma_base, 4, hwif->name)) {
- printk(KERN_CONT " -- Error, ports in use.\n");
+ if (ide_allocate_dma_engine(hwif))
return;
- }
-
- hwif->dmatable_cpu = pci_alloc_consistent(dev, PRD_ENTRIES * PRD_BYTES,
- &hwif->dmatable_dma);
- if (!hwif->dmatable_cpu) {
- printk(KERN_CONT " -- Error, unable to allocate DMA table.\n");
- release_region(hwif->dma_base, 4);
- return;
- }
- printk(KERN_CONT "\n");
local_irq_save(flags);
/* put config reg into first byte of hwif->select_data */
@@ -291,14 +280,6 @@
/* sharing IRQ with mate */
hwif->irq = hwif->mate->irq;
- hwif->dma_host_set = &trm290_dma_host_set;
- hwif->dma_setup = &trm290_dma_setup;
- hwif->dma_exec_cmd = &trm290_dma_exec_cmd;
- hwif->dma_start = &trm290_dma_start;
- hwif->ide_dma_end = &trm290_ide_dma_end;
- hwif->ide_dma_test_irq = &trm290_ide_dma_test_irq;
-
- hwif->selectproc = &trm290_selectproc;
#if 1
{
/*
@@ -328,10 +309,27 @@
#endif
}
+static const struct ide_port_ops trm290_port_ops = {
+ .selectproc = trm290_selectproc,
+};
+
+static struct ide_dma_ops trm290_dma_ops = {
+ .dma_host_set = trm290_dma_host_set,
+ .dma_setup = trm290_dma_setup,
+ .dma_exec_cmd = trm290_dma_exec_cmd,
+ .dma_start = trm290_dma_start,
+ .dma_end = trm290_dma_end,
+ .dma_test_irq = trm290_dma_test_irq,
+ .dma_lost_irq = ide_dma_lost_irq,
+ .dma_timeout = ide_dma_timeout,
+};
+
static const struct ide_port_info trm290_chipset __devinitdata = {
.name = "TRM290",
.init_hwif = init_hwif_trm290,
.chipset = ide_trm290,
+ .port_ops = &trm290_port_ops,
+ .dma_ops = &trm290_dma_ops,
.host_flags = IDE_HFLAG_NO_ATAPI_DMA |
#if 0 /* play it safe for now */
IDE_HFLAG_TRUST_BIOS_FOR_DMA |
diff --git a/drivers/ide/pci/via82cxxx.c b/drivers/ide/pci/via82cxxx.c
index cff3cafe..bbd17be 100644
--- a/drivers/ide/pci/via82cxxx.c
+++ b/drivers/ide/pci/via82cxxx.c
@@ -415,19 +415,17 @@
return ATA_CBL_PATA40;
}
-static void __devinit init_hwif_via82cxxx(ide_hwif_t *hwif)
-{
- hwif->set_pio_mode = &via_set_pio_mode;
- hwif->set_dma_mode = &via_set_drive;
-
- hwif->cable_detect = via82cxxx_cable_detect;
-}
+static const struct ide_port_ops via_port_ops = {
+ .set_pio_mode = via_set_pio_mode,
+ .set_dma_mode = via_set_drive,
+ .cable_detect = via82cxxx_cable_detect,
+};
static const struct ide_port_info via82cxxx_chipset __devinitdata = {
.name = "VP_IDE",
.init_chipset = init_chipset_via82cxxx,
- .init_hwif = init_hwif_via82cxxx,
.enablebits = { { 0x40, 0x02, 0x02 }, { 0x40, 0x01, 0x01 } },
+ .port_ops = &via_port_ops,
.host_flags = IDE_HFLAG_PIO_NO_BLACKLIST |
IDE_HFLAG_ABUSE_SET_DMA_MODE |
IDE_HFLAG_POST_SET_MODE |
diff --git a/drivers/ide/ppc/mpc8xx.c b/drivers/ide/ppc/mpc8xx.c
index 467656f..a82f6ef 100644
--- a/drivers/ide/ppc/mpc8xx.c
+++ b/drivers/ide/ppc/mpc8xx.c
@@ -438,10 +438,14 @@
#elif defined(CONFIG_IDE_EXT_DIRECT)
printk("%s[%d] %s: not implemented yet!\n",
- __FILE__,__LINE__,__FUNCTION__);
+ __FILE__, __LINE__, __func__);
#endif /* defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_IDE_8xx_PCMCIA */
}
+static const struct ide_port_ops m8xx_port_ops = {
+ .set_pio_mode = m8xx_ide_set_pio_mode,
+};
+
static void
ide_interrupt_ack (void *dev)
{
@@ -810,9 +814,8 @@
ide_hwif_t *hwif = &ide_hwifs[0];
ide_init_port_hw(hwif, &hw);
- hwif->mmio = 1;
hwif->pio_mask = ATA_PIO4;
- hwif->set_pio_mode = m8xx_ide_set_pio_mode;
+ hwif->port_ops = &m8xx_port_ops;
idx[0] = 0;
}
@@ -822,9 +825,8 @@
ide_hwif_t *mate = &ide_hwifs[1];
ide_init_port_hw(mate, &hw);
- mate->mmio = 1;
mate->pio_mask = ATA_PIO4;
- mate->set_pio_mode = m8xx_ide_set_pio_mode;
+ mate->port_ops = &m8xx_port_ops;
idx[1] = 1;
}
diff --git a/drivers/ide/ppc/pmac.c b/drivers/ide/ppc/pmac.c
index 177961e..185faa0 100644
--- a/drivers/ide/ppc/pmac.c
+++ b/drivers/ide/ppc/pmac.c
@@ -409,7 +409,7 @@
*/
#define IDE_WAKEUP_DELAY (1*HZ)
-static int pmac_ide_setup_dma(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif);
+static int pmac_ide_init_dma(ide_hwif_t *, const struct ide_port_info *);
static int pmac_ide_build_dmatable(ide_drive_t *drive, struct request *rq);
static void pmac_ide_selectproc(ide_drive_t *drive);
static void pmac_ide_kauai_selectproc(ide_drive_t *drive);
@@ -918,11 +918,29 @@
return 0;
}
+static const struct ide_port_ops pmac_ide_ata6_port_ops = {
+ .set_pio_mode = pmac_ide_set_pio_mode,
+ .set_dma_mode = pmac_ide_set_dma_mode,
+ .selectproc = pmac_ide_kauai_selectproc,
+};
+
+static const struct ide_port_ops pmac_ide_port_ops = {
+ .set_pio_mode = pmac_ide_set_pio_mode,
+ .set_dma_mode = pmac_ide_set_dma_mode,
+ .selectproc = pmac_ide_selectproc,
+};
+
+static const struct ide_dma_ops pmac_dma_ops;
+
static const struct ide_port_info pmac_port_info = {
+ .init_dma = pmac_ide_init_dma,
.chipset = ide_pmac,
+#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
+ .dma_ops = &pmac_dma_ops,
+#endif
+ .port_ops = &pmac_ide_port_ops,
.host_flags = IDE_HFLAG_SET_PIO_MODE_KEEP_DMA |
IDE_HFLAG_POST_SET_MODE |
- IDE_HFLAG_NO_DMA | /* no SFF-style DMA */
IDE_HFLAG_UNMASK_IRQS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
@@ -947,12 +965,15 @@
pmif->broken_dma = pmif->broken_dma_warn = 0;
if (of_device_is_compatible(np, "shasta-ata")) {
pmif->kind = controller_sh_ata6;
+ d.port_ops = &pmac_ide_ata6_port_ops;
d.udma_mask = ATA_UDMA6;
} else if (of_device_is_compatible(np, "kauai-ata")) {
pmif->kind = controller_un_ata6;
+ d.port_ops = &pmac_ide_ata6_port_ops;
d.udma_mask = ATA_UDMA5;
} else if (of_device_is_compatible(np, "K2-UATA")) {
pmif->kind = controller_k2_ata6;
+ d.port_ops = &pmac_ide_ata6_port_ops;
d.udma_mask = ATA_UDMA5;
} else if (of_device_is_compatible(np, "keylargo-ata")) {
if (strcmp(np->name, "ata-4") == 0) {
@@ -1029,37 +1050,29 @@
default_hwif_mmiops(hwif);
hwif->OUTBSYNC = pmac_outbsync;
- /* Tell common code _not_ to mess with resources */
- hwif->mmio = 1;
hwif->hwif_data = pmif;
ide_init_port_hw(hwif, hw);
- hwif->noprobe = pmif->mediabay;
hwif->cbl = pmif->cable_80 ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
- hwif->set_pio_mode = pmac_ide_set_pio_mode;
- if (pmif->kind == controller_un_ata6
- || pmif->kind == controller_k2_ata6
- || pmif->kind == controller_sh_ata6)
- hwif->selectproc = pmac_ide_kauai_selectproc;
- else
- hwif->selectproc = pmac_ide_selectproc;
- hwif->set_dma_mode = pmac_ide_set_dma_mode;
printk(KERN_INFO "ide%d: Found Apple %s controller, bus ID %d%s, irq %d\n",
hwif->index, model_name[pmif->kind], pmif->aapl_bus_id,
pmif->mediabay ? " (mediabay)" : "", hwif->irq);
-
+
+ if (pmif->mediabay) {
#ifdef CONFIG_PMAC_MEDIABAY
- if (pmif->mediabay && check_media_bay_by_base(pmif->regbase, MB_CD) == 0)
- hwif->noprobe = 0;
-#endif /* CONFIG_PMAC_MEDIABAY */
+ if (check_media_bay_by_base(pmif->regbase, MB_CD)) {
+#else
+ if (1) {
+#endif
+ hwif->drives[0].noprobe = 1;
+ hwif->drives[1].noprobe = 1;
+ }
+ }
#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
if (pmif->cable_80 == 0)
d.udma_mask &= ATA_UDMA2;
- /* has a DBDMA controller channel */
- if (pmif->dma_regs == 0 || pmac_ide_setup_dma(pmif, hwif) < 0)
#endif
- d.udma_mask = d.mwdma_mask = 0;
idx[0] = hwif->index;
@@ -1662,18 +1675,31 @@
printk(KERN_ERR "ide-pmac lost interrupt, dma status: %lx\n", status);
}
+static const struct ide_dma_ops pmac_dma_ops = {
+ .dma_host_set = pmac_ide_dma_host_set,
+ .dma_setup = pmac_ide_dma_setup,
+ .dma_exec_cmd = pmac_ide_dma_exec_cmd,
+ .dma_start = pmac_ide_dma_start,
+ .dma_end = pmac_ide_dma_end,
+ .dma_test_irq = pmac_ide_dma_test_irq,
+ .dma_timeout = ide_dma_timeout,
+ .dma_lost_irq = pmac_ide_dma_lost_irq,
+};
+
/*
* Allocate the data structures needed for using DMA with an interface
* and fill the proper list of functions pointers
*/
-static int __devinit pmac_ide_setup_dma(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif)
+static int __devinit pmac_ide_init_dma(ide_hwif_t *hwif,
+ const struct ide_port_info *d)
{
+ pmac_ide_hwif_t *pmif = (pmac_ide_hwif_t *)hwif->hwif_data;
struct pci_dev *dev = to_pci_dev(hwif->dev);
/* We won't need pci_dev if we switch to generic consistent
* DMA routines ...
*/
- if (dev == NULL)
+ if (dev == NULL || pmif->dma_regs == 0)
return -ENODEV;
/*
* Allocate space for the DBDMA commands.
@@ -1692,18 +1718,14 @@
hwif->sg_max_nents = MAX_DCMDS;
- hwif->dma_host_set = &pmac_ide_dma_host_set;
- hwif->dma_setup = &pmac_ide_dma_setup;
- hwif->dma_exec_cmd = &pmac_ide_dma_exec_cmd;
- hwif->dma_start = &pmac_ide_dma_start;
- hwif->ide_dma_end = &pmac_ide_dma_end;
- hwif->ide_dma_test_irq = &pmac_ide_dma_test_irq;
- hwif->dma_timeout = &ide_dma_timeout;
- hwif->dma_lost_irq = &pmac_ide_dma_lost_irq;
-
return 0;
}
-
+#else
+static int __devinit pmac_ide_init_dma(ide_hwif_t *hwif,
+ const struct ide_port_info *d)
+{
+ return -EOPNOTSUPP;
+}
#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
module_init(pmac_ide_probe);
diff --git a/drivers/ide/setup-pci.c b/drivers/ide/setup-pci.c
index 6302010..5171601 100644
--- a/drivers/ide/setup-pci.c
+++ b/drivers/ide/setup-pci.c
@@ -72,16 +72,16 @@
}
/**
- * ide_get_or_set_dma_base - setup BMIBA
- * @d: IDE port info
+ * ide_pci_dma_base - setup BMIBA
* @hwif: IDE interface
+ * @d: IDE port info
*
* Fetch the DMA Bus-Master-I/O-Base-Address (BMIBA) from PCI space.
* Where a device has a partner that is already in DMA mode we check
* and enforce IDE simplex rules.
*/
-static unsigned long ide_get_or_set_dma_base(const struct ide_port_info *d, ide_hwif_t *hwif)
+unsigned long ide_pci_dma_base(ide_hwif_t *hwif, const struct ide_port_info *d)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
unsigned long dma_base = 0;
@@ -132,6 +132,31 @@
out:
return dma_base;
}
+EXPORT_SYMBOL_GPL(ide_pci_dma_base);
+
+/*
+ * Set up BM-DMA capability (PnP BIOS should have done this)
+ */
+int ide_pci_set_master(struct pci_dev *dev, const char *name)
+{
+ u16 pcicmd;
+
+ pci_read_config_word(dev, PCI_COMMAND, &pcicmd);
+
+ if ((pcicmd & PCI_COMMAND_MASTER) == 0) {
+ pci_set_master(dev);
+
+ if (pci_read_config_word(dev, PCI_COMMAND, &pcicmd) ||
+ (pcicmd & PCI_COMMAND_MASTER) == 0) {
+ printk(KERN_ERR "%s: error updating PCICMD on %s\n",
+ name, pci_name(dev));
+ return -EIO;
+ }
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ide_pci_set_master);
#endif /* CONFIG_BLK_DEV_IDEDMA_PCI */
void ide_setup_pci_noise(struct pci_dev *dev, const struct ide_port_info *d)
@@ -158,7 +183,7 @@
static int ide_pci_enable(struct pci_dev *dev, const struct ide_port_info *d)
{
- int ret;
+ int ret, bars;
if (pci_enable_device(dev)) {
ret = pci_enable_device_io(dev);
@@ -181,13 +206,21 @@
goto out;
}
- /* FIXME: Temporary - until we put in the hotplug interface logic
- Check that the bits we want are not in use by someone else. */
- ret = pci_request_region(dev, 4, "ide_tmp");
- if (ret < 0)
- goto out;
+ if (d->host_flags & IDE_HFLAG_SINGLE)
+ bars = (1 << 2) - 1;
+ else
+ bars = (1 << 4) - 1;
- pci_release_region(dev, 4);
+ if ((d->host_flags & IDE_HFLAG_NO_DMA) == 0) {
+ if (d->host_flags & IDE_HFLAG_CS5520)
+ bars |= (1 << 2);
+ else
+ bars |= (1 << 4);
+ }
+
+ ret = pci_request_selected_regions(dev, bars, d->name);
+ if (ret < 0)
+ printk(KERN_ERR "%s: can't reserve resources\n", d->name);
out:
return ret;
}
@@ -314,7 +347,6 @@
ide_init_port_hw(hwif, &hw);
hwif->dev = &dev->dev;
- hwif->cds = d;
return hwif;
}
@@ -330,40 +362,33 @@
* state
*/
-void ide_hwif_setup_dma(ide_hwif_t *hwif, const struct ide_port_info *d)
+int ide_hwif_setup_dma(ide_hwif_t *hwif, const struct ide_port_info *d)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
- u16 pcicmd;
-
- pci_read_config_word(dev, PCI_COMMAND, &pcicmd);
if ((d->host_flags & IDE_HFLAG_NO_AUTODMA) == 0 ||
((dev->class >> 8) == PCI_CLASS_STORAGE_IDE &&
(dev->class & 0x80))) {
- unsigned long dma_base = ide_get_or_set_dma_base(d, hwif);
- if (dma_base && !(pcicmd & PCI_COMMAND_MASTER)) {
- /*
- * Set up BM-DMA capability
- * (PnP BIOS should have done this)
- */
- pci_set_master(dev);
- if (pci_read_config_word(dev, PCI_COMMAND, &pcicmd) || !(pcicmd & PCI_COMMAND_MASTER)) {
- printk(KERN_ERR "%s: %s error updating PCICMD\n",
- hwif->name, d->name);
- dma_base = 0;
- }
- }
- if (dma_base) {
- if (d->init_dma) {
- d->init_dma(hwif, dma_base);
- } else {
- ide_setup_dma(hwif, dma_base);
- }
- } else {
- printk(KERN_INFO "%s: %s Bus-Master DMA disabled "
- "(BIOS)\n", hwif->name, d->name);
- }
+ unsigned long base = ide_pci_dma_base(hwif, d);
+
+ if (base == 0 || ide_pci_set_master(dev, d->name) < 0)
+ return -1;
+
+ if (hwif->mmio)
+ printk(KERN_INFO " %s: MMIO-DMA\n", hwif->name);
+ else
+ printk(KERN_INFO " %s: BM-DMA at 0x%04lx-0x%04lx\n",
+ hwif->name, base, base + 7);
+
+ hwif->extra_base = base + (hwif->channel ? 8 : 16);
+
+ if (ide_allocate_dma_engine(hwif))
+ return -1;
+
+ ide_setup_dma(hwif, base);
}
+
+ return 0;
}
#endif /* CONFIG_BLK_DEV_IDEDMA_PCI */
diff --git a/drivers/scsi/ide-scsi.c b/drivers/scsi/ide-scsi.c
index 93c3fc2..3638fa8 100644
--- a/drivers/scsi/ide-scsi.c
+++ b/drivers/scsi/ide-scsi.c
@@ -393,7 +393,7 @@
printk ("ide-scsi: %s: DMA complete\n", drive->name);
#endif /* IDESCSI_DEBUG_LOG */
pc->xferred = pc->req_xfer;
- (void) HWIF(drive)->ide_dma_end(drive);
+ (void)hwif->dma_ops->dma_end(drive);
}
/* Clear the interrupt */
@@ -498,7 +498,7 @@
drive->hwif->atapi_output_bytes(drive, scsi->pc->c, 12);
if (pc->flags & PC_FLAG_DMA_OK) {
pc->flags |= PC_FLAG_DMA_IN_PROGRESS;
- hwif->dma_start(drive);
+ hwif->dma_ops->dma_start(drive);
}
return ide_started;
}
@@ -560,7 +560,7 @@
if (drive->using_dma && !idescsi_map_sg(drive, pc)) {
hwif->sg_mapped = 1;
- dma = !hwif->dma_setup(drive);
+ dma = !hwif->dma_ops->dma_setup(drive);
hwif->sg_mapped = 0;
}
diff --git a/include/asm-alpha/bitops.h b/include/asm-alpha/bitops.h
index 9e19a70..15f3ae2 100644
--- a/include/asm-alpha/bitops.h
+++ b/include/asm-alpha/bitops.h
@@ -388,6 +388,11 @@
}
#endif
+static inline unsigned long __fls(unsigned long x)
+{
+ return fls64(x) - 1;
+}
+
static inline int fls(int x)
{
return fls64((unsigned int) x);
diff --git a/include/asm-generic/bitops/__fls.h b/include/asm-generic/bitops/__fls.h
new file mode 100644
index 0000000..be24465
--- /dev/null
+++ b/include/asm-generic/bitops/__fls.h
@@ -0,0 +1,43 @@
+#ifndef _ASM_GENERIC_BITOPS___FLS_H_
+#define _ASM_GENERIC_BITOPS___FLS_H_
+
+#include <asm/types.h>
+
+/**
+ * __fls - find last (most-significant) set bit in a long word
+ * @word: the word to search
+ *
+ * Undefined if no set bit exists, so code should check against 0 first.
+ */
+static inline unsigned long __fls(unsigned long word)
+{
+ int num = BITS_PER_LONG - 1;
+
+#if BITS_PER_LONG == 64
+ if (!(word & (~0ul << 32))) {
+ num -= 32;
+ word <<= 32;
+ }
+#endif
+ if (!(word & (~0ul << (BITS_PER_LONG-16)))) {
+ num -= 16;
+ word <<= 16;
+ }
+ if (!(word & (~0ul << (BITS_PER_LONG-8)))) {
+ num -= 8;
+ word <<= 8;
+ }
+ if (!(word & (~0ul << (BITS_PER_LONG-4)))) {
+ num -= 4;
+ word <<= 4;
+ }
+ if (!(word & (~0ul << (BITS_PER_LONG-2)))) {
+ num -= 2;
+ word <<= 2;
+ }
+ if (!(word & (~0ul << (BITS_PER_LONG-1))))
+ num -= 1;
+ return num;
+}
+
+#endif /* _ASM_GENERIC_BITOPS___FLS_H_ */
diff --git a/include/asm-generic/bitops/find.h b/include/asm-generic/bitops/find.h
index 72a51e5..1914e97 100644
--- a/include/asm-generic/bitops/find.h
+++ b/include/asm-generic/bitops/find.h
@@ -1,11 +1,13 @@
#ifndef _ASM_GENERIC_BITOPS_FIND_H_
#define _ASM_GENERIC_BITOPS_FIND_H_
+#ifndef CONFIG_GENERIC_FIND_NEXT_BIT
extern unsigned long find_next_bit(const unsigned long *addr, unsigned long
size, unsigned long offset);
extern unsigned long find_next_zero_bit(const unsigned long *addr, unsigned
long size, unsigned long offset);
+#endif
#define find_first_bit(addr, size) find_next_bit((addr), (size), 0)
#define find_first_zero_bit(addr, size) find_next_zero_bit((addr), (size), 0)
diff --git a/include/asm-generic/bitops/fls64.h b/include/asm-generic/bitops/fls64.h
index 1b6b17c..86d403f 100644
--- a/include/asm-generic/bitops/fls64.h
+++ b/include/asm-generic/bitops/fls64.h
@@ -3,6 +3,18 @@
#include <asm/types.h>
+/**
+ * fls64 - find last set bit in a 64-bit word
+ * @x: the word to search
+ *
+ * This is defined in a similar way as the libc and compiler builtin
+ * ffsll, but returns the position of the most significant set bit.
+ *
+ * fls64(value) returns 0 if value is 0 or the position of the last
+ * set bit if value is nonzero. The last (most significant) bit is
+ * at position 64.
+ */
+#if BITS_PER_LONG == 32
static inline int fls64(__u64 x)
{
__u32 h = x >> 32;
@@ -10,5 +22,15 @@
return fls(h) + 32;
return fls(x);
}
+#elif BITS_PER_LONG == 64
+static inline int fls64(__u64 x)
+{
+ if (x == 0)
+ return 0;
+ return __fls(x) + 1;
+}
+#else
+#error BITS_PER_LONG not 32 or 64
+#endif
#endif /* _ASM_GENERIC_BITOPS_FLS64_H_ */
diff --git a/include/asm-ia64/bitops.h b/include/asm-ia64/bitops.h
index 953d3df..e2ca800 100644
--- a/include/asm-ia64/bitops.h
+++ b/include/asm-ia64/bitops.h
@@ -407,6 +407,22 @@
return ia64_popcnt(x);
}
+/*
+ * Find the last (most significant) bit set. Undefined for x==0.
+ * Bits are numbered from 0..63 (e.g., __fls(9) == 3).
+ */
+static inline unsigned long
+__fls (unsigned long x)
+{
+ x |= x >> 1;
+ x |= x >> 2;
+ x |= x >> 4;
+ x |= x >> 8;
+ x |= x >> 16;
+ x |= x >> 32;
+ return ia64_popcnt(x) - 1;
+}
+
#include <asm-generic/bitops/fls64.h>
/*
diff --git a/include/asm-mips/bitops.h b/include/asm-mips/bitops.h
index ec75ce4..c2bd126 100644
--- a/include/asm-mips/bitops.h
+++ b/include/asm-mips/bitops.h
@@ -591,6 +591,11 @@
return 63 - lz;
}
+static inline unsigned long __fls(unsigned long x)
+{
+ return __ilog2(x);
+}
+
#if defined(CONFIG_CPU_MIPS32) || defined(CONFIG_CPU_MIPS64)
/*
diff --git a/include/asm-mips/mach-au1x00/au1xxx_ide.h b/include/asm-mips/mach-au1x00/au1xxx_ide.h
index 89655c0..b493a5e 100644
--- a/include/asm-mips/mach-au1x00/au1xxx_ide.h
+++ b/include/asm-mips/mach-au1x00/au1xxx_ide.h
@@ -70,7 +70,6 @@
ide_hwif_t *hwif;
#ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
ide_drive_t *drive;
- u8 white_list, black_list;
struct dbdma_cmd *dma_table_cpu;
dma_addr_t dma_table_dma;
#endif
@@ -81,47 +80,6 @@
#endif
} _auide_hwif;
-#ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
-/* HD white list */
-static const struct drive_list_entry dma_white_list [] = {
-/*
- * Hitachi
- */
- { "HITACHI_DK14FA-20" , NULL },
- { "HTS726060M9AT00" , NULL },
-/*
- * Maxtor
- */
- { "Maxtor 6E040L0" , NULL },
- { "Maxtor 6Y080P0" , NULL },
- { "Maxtor 6Y160P0" , NULL },
-/*
- * Seagate
- */
- { "ST3120026A" , NULL },
- { "ST320014A" , NULL },
- { "ST94011A" , NULL },
- { "ST340016A" , NULL },
-/*
- * Western Digital
- */
- { "WDC WD400UE-00HCT0" , NULL },
- { "WDC WD400JB-00JJC0" , NULL },
- { NULL , NULL }
-};
-
-/* HD black list */
-static const struct drive_list_entry dma_black_list [] = {
-/*
- * Western Digital
- */
- { "WDC WD100EB-00CGH0" , NULL },
- { "WDC WD200BB-00AUA1" , NULL },
- { "WDC AC24300L" , NULL },
- { NULL , NULL }
-};
-#endif
-
/*******************************************************************************
* PIO Mode timing calculation : *
* *
diff --git a/include/asm-parisc/bitops.h b/include/asm-parisc/bitops.h
index f8eebcb..7a6ea10 100644
--- a/include/asm-parisc/bitops.h
+++ b/include/asm-parisc/bitops.h
@@ -210,6 +210,7 @@
return ret;
}
+#include <asm-generic/bitops/__fls.h>
#include <asm-generic/bitops/fls64.h>
#include <asm-generic/bitops/hweight.h>
#include <asm-generic/bitops/lock.h>
diff --git a/include/asm-powerpc/bitops.h b/include/asm-powerpc/bitops.h
index a99a749..897eade 100644
--- a/include/asm-powerpc/bitops.h
+++ b/include/asm-powerpc/bitops.h
@@ -313,6 +313,11 @@
return 32 - lz;
}
+static __inline__ unsigned long __fls(unsigned long x)
+{
+ return __ilog2(x);
+}
+
/*
* 64-bit can do this using one cntlzd (count leading zeroes doubleword)
* instruction; for 32-bit we use the generic version, which does two
diff --git a/include/asm-s390/bitops.h b/include/asm-s390/bitops.h
index 965394e..b4eb24a 100644
--- a/include/asm-s390/bitops.h
+++ b/include/asm-s390/bitops.h
@@ -769,6 +769,7 @@
}
#include <asm-generic/bitops/fls.h>
+#include <asm-generic/bitops/__fls.h>
#include <asm-generic/bitops/fls64.h>
#include <asm-generic/bitops/hweight.h>
diff --git a/include/asm-sh/bitops.h b/include/asm-sh/bitops.h
index b6ba5a6..d7d382f 100644
--- a/include/asm-sh/bitops.h
+++ b/include/asm-sh/bitops.h
@@ -95,6 +95,7 @@
#include <asm-generic/bitops/ext2-atomic.h>
#include <asm-generic/bitops/minix.h>
#include <asm-generic/bitops/fls.h>
+#include <asm-generic/bitops/__fls.h>
#include <asm-generic/bitops/fls64.h>
#endif /* __KERNEL__ */
diff --git a/include/asm-sparc64/bitops.h b/include/asm-sparc64/bitops.h
index 982ce89..11f9d81 100644
--- a/include/asm-sparc64/bitops.h
+++ b/include/asm-sparc64/bitops.h
@@ -34,6 +34,7 @@
#include <asm-generic/bitops/ffz.h>
#include <asm-generic/bitops/__ffs.h>
#include <asm-generic/bitops/fls.h>
+#include <asm-generic/bitops/__fls.h>
#include <asm-generic/bitops/fls64.h>
#ifdef __KERNEL__
diff --git a/include/asm-x86/bitops.h b/include/asm-x86/bitops.h
index 1ae7b27..b81a4d4 100644
--- a/include/asm-x86/bitops.h
+++ b/include/asm-x86/bitops.h
@@ -62,12 +62,9 @@
*/
static inline void __set_bit(int nr, volatile void *addr)
{
- asm volatile("bts %1,%0"
- : ADDR
- : "Ir" (nr) : "memory");
+ asm volatile("bts %1,%0" : ADDR : "Ir" (nr) : "memory");
}
-
/**
* clear_bit - Clears a bit in memory
* @nr: Bit to clear
@@ -297,19 +294,145 @@
static int test_bit(int nr, const volatile unsigned long *addr);
#endif
-#define test_bit(nr,addr) \
- (__builtin_constant_p(nr) ? \
- constant_test_bit((nr),(addr)) : \
- variable_test_bit((nr),(addr)))
+#define test_bit(nr, addr) \
+ (__builtin_constant_p((nr)) \
+ ? constant_test_bit((nr), (addr)) \
+ : variable_test_bit((nr), (addr)))
+
+/**
+ * __ffs - find first set bit in word
+ * @word: The word to search
+ *
+ * Undefined if no bit exists, so code should check against 0 first.
+ */
+static inline unsigned long __ffs(unsigned long word)
+{
+ asm("bsf %1,%0"
+ : "=r" (word)
+ : "rm" (word));
+ return word;
+}
+
+/**
+ * ffz - find first zero bit in word
+ * @word: The word to search
+ *
+ * Undefined if no zero exists, so code should check against ~0UL first.
+ */
+static inline unsigned long ffz(unsigned long word)
+{
+ asm("bsf %1,%0"
+ : "=r" (word)
+ : "r" (~word));
+ return word;
+}
+
+/*
+ * __fls: find last set bit in word
+ * @word: The word to search
+ *
+ * Undefined if no zero exists, so code should check against ~0UL first.
+ */
+static inline unsigned long __fls(unsigned long word)
+{
+ asm("bsr %1,%0"
+ : "=r" (word)
+ : "rm" (word));
+ return word;
+}
+
+#ifdef __KERNEL__
+/**
+ * ffs - find first set bit in word
+ * @x: the word to search
+ *
+ * This is defined the same way as the libc and compiler builtin ffs
+ * routines, therefore differs in spirit from the other bitops.
+ *
+ * ffs(value) returns 0 if value is 0 or the position of the first
+ * set bit if value is nonzero. The first (least significant) bit
+ * is at position 1.
+ */
+static inline int ffs(int x)
+{
+ int r;
+#ifdef CONFIG_X86_CMOV
+ asm("bsfl %1,%0\n\t"
+ "cmovzl %2,%0"
+ : "=r" (r) : "rm" (x), "r" (-1));
+#else
+ asm("bsfl %1,%0\n\t"
+ "jnz 1f\n\t"
+ "movl $-1,%0\n"
+ "1:" : "=r" (r) : "rm" (x));
+#endif
+ return r + 1;
+}
+
+/**
+ * fls - find last set bit in word
+ * @x: the word to search
+ *
+ * This is defined in a similar way as the libc and compiler builtin
+ * ffs, but returns the position of the most significant set bit.
+ *
+ * fls(value) returns 0 if value is 0 or the position of the last
+ * set bit if value is nonzero. The last (most significant) bit is
+ * at position 32.
+ */
+static inline int fls(int x)
+{
+ int r;
+#ifdef CONFIG_X86_CMOV
+ asm("bsrl %1,%0\n\t"
+ "cmovzl %2,%0"
+ : "=&r" (r) : "rm" (x), "rm" (-1));
+#else
+ asm("bsrl %1,%0\n\t"
+ "jnz 1f\n\t"
+ "movl $-1,%0\n"
+ "1:" : "=r" (r) : "rm" (x));
+#endif
+ return r + 1;
+}
+#endif /* __KERNEL__ */
#undef BASE_ADDR
#undef BIT_ADDR
#undef ADDR
-#ifdef CONFIG_X86_32
-# include "bitops_32.h"
-#else
-# include "bitops_64.h"
-#endif
+static inline void set_bit_string(unsigned long *bitmap,
+ unsigned long i, int len)
+{
+ unsigned long end = i + len;
+ while (i < end) {
+ __set_bit(i, bitmap);
+ i++;
+ }
+}
+#ifdef __KERNEL__
+
+#include <asm-generic/bitops/sched.h>
+
+#define ARCH_HAS_FAST_MULTIPLIER 1
+
+#include <asm-generic/bitops/hweight.h>
+
+#endif /* __KERNEL__ */
+
+#include <asm-generic/bitops/fls64.h>
+
+#ifdef __KERNEL__
+
+#include <asm-generic/bitops/ext2-non-atomic.h>
+
+#define ext2_set_bit_atomic(lock, nr, addr) \
+ test_and_set_bit((nr), (unsigned long *)(addr))
+#define ext2_clear_bit_atomic(lock, nr, addr) \
+ test_and_clear_bit((nr), (unsigned long *)(addr))
+
+#include <asm-generic/bitops/minix.h>
+
+#endif /* __KERNEL__ */
#endif /* _ASM_X86_BITOPS_H */
diff --git a/include/asm-x86/bitops_32.h b/include/asm-x86/bitops_32.h
deleted file mode 100644
index 2513a81..0000000
--- a/include/asm-x86/bitops_32.h
+++ /dev/null
@@ -1,166 +0,0 @@
-#ifndef _I386_BITOPS_H
-#define _I386_BITOPS_H
-
-/*
- * Copyright 1992, Linus Torvalds.
- */
-
-/**
- * find_first_zero_bit - find the first zero bit in a memory region
- * @addr: The address to start the search at
- * @size: The maximum size to search
- *
- * Returns the bit number of the first zero bit, not the number of the byte
- * containing a bit.
- */
-static inline int find_first_zero_bit(const unsigned long *addr, unsigned size)
-{
- int d0, d1, d2;
- int res;
-
- if (!size)
- return 0;
- /* This looks at memory.
- * Mark it volatile to tell gcc not to move it around
- */
- asm volatile("movl $-1,%%eax\n\t"
- "xorl %%edx,%%edx\n\t"
- "repe; scasl\n\t"
- "je 1f\n\t"
- "xorl -4(%%edi),%%eax\n\t"
- "subl $4,%%edi\n\t"
- "bsfl %%eax,%%edx\n"
- "1:\tsubl %%ebx,%%edi\n\t"
- "shll $3,%%edi\n\t"
- "addl %%edi,%%edx"
- : "=d" (res), "=&c" (d0), "=&D" (d1), "=&a" (d2)
- : "1" ((size + 31) >> 5), "2" (addr),
- "b" (addr) : "memory");
- return res;
-}
-
-/**
- * find_next_zero_bit - find the first zero bit in a memory region
- * @addr: The address to base the search on
- * @offset: The bit number to start searching at
- * @size: The maximum size to search
- */
-int find_next_zero_bit(const unsigned long *addr, int size, int offset);
-
-/**
- * __ffs - find first bit in word.
- * @word: The word to search
- *
- * Undefined if no bit exists, so code should check against 0 first.
- */
-static inline unsigned long __ffs(unsigned long word)
-{
- __asm__("bsfl %1,%0"
- :"=r" (word)
- :"rm" (word));
- return word;
-}
-
-/**
- * find_first_bit - find the first set bit in a memory region
- * @addr: The address to start the search at
- * @size: The maximum size to search
- *
- * Returns the bit number of the first set bit, not the number of the byte
- * containing a bit.
- */
-static inline unsigned find_first_bit(const unsigned long *addr, unsigned size)
-{
- unsigned x = 0;
-
- while (x < size) {
- unsigned long val = *addr++;
- if (val)
- return __ffs(val) + x;
- x += sizeof(*addr) << 3;
- }
- return x;
-}
-
-/**
- * find_next_bit - find the first set bit in a memory region
- * @addr: The address to base the search on
- * @offset: The bit number to start searching at
- * @size: The maximum size to search
- */
-int find_next_bit(const unsigned long *addr, int size, int offset);
-
-/**
- * ffz - find first zero in word.
- * @word: The word to search
- *
- * Undefined if no zero exists, so code should check against ~0UL first.
- */
-static inline unsigned long ffz(unsigned long word)
-{
- __asm__("bsfl %1,%0"
- :"=r" (word)
- :"r" (~word));
- return word;
-}
-
-#ifdef __KERNEL__
-
-#include <asm-generic/bitops/sched.h>
-
-/**
- * ffs - find first bit set
- * @x: the word to search
- *
- * This is defined the same way as
- * the libc and compiler builtin ffs routines, therefore
- * differs in spirit from the above ffz() (man ffs).
- */
-static inline int ffs(int x)
-{
- int r;
-
- __asm__("bsfl %1,%0\n\t"
- "jnz 1f\n\t"
- "movl $-1,%0\n"
- "1:" : "=r" (r) : "rm" (x));
- return r+1;
-}
-
-/**
- * fls - find last bit set
- * @x: the word to search
- *
- * This is defined the same way as ffs().
- */
-static inline int fls(int x)
-{
- int r;
-
- __asm__("bsrl %1,%0\n\t"
- "jnz 1f\n\t"
- "movl $-1,%0\n"
- "1:" : "=r" (r) : "rm" (x));
- return r+1;
-}
-
-#include <asm-generic/bitops/hweight.h>
-
-#endif /* __KERNEL__ */
-
-#include <asm-generic/bitops/fls64.h>
-
-#ifdef __KERNEL__
-
-#include <asm-generic/bitops/ext2-non-atomic.h>
-
-#define ext2_set_bit_atomic(lock, nr, addr) \
- test_and_set_bit((nr), (unsigned long *)(addr))
-#define ext2_clear_bit_atomic(lock, nr, addr) \
- test_and_clear_bit((nr), (unsigned long *)(addr))
-
-#include <asm-generic/bitops/minix.h>
-
-#endif /* __KERNEL__ */
-
-#endif /* _I386_BITOPS_H */
diff --git a/include/asm-x86/bitops_64.h b/include/asm-x86/bitops_64.h
deleted file mode 100644
index 365f820..0000000
--- a/include/asm-x86/bitops_64.h
+++ /dev/null
@@ -1,162 +0,0 @@
-#ifndef _X86_64_BITOPS_H
-#define _X86_64_BITOPS_H
-
-/*
- * Copyright 1992, Linus Torvalds.
- */
-
-extern long find_first_zero_bit(const unsigned long *addr, unsigned long size);
-extern long find_next_zero_bit(const unsigned long *addr, long size, long offset);
-extern long find_first_bit(const unsigned long *addr, unsigned long size);
-extern long find_next_bit(const unsigned long *addr, long size, long offset);
-
-/* return index of first bet set in val or max when no bit is set */
-static inline long __scanbit(unsigned long val, unsigned long max)
-{
- asm("bsfq %1,%0 ; cmovz %2,%0" : "=&r" (val) : "r" (val), "r" (max));
- return val;
-}
-
-#define find_next_bit(addr,size,off) \
-((__builtin_constant_p(size) && (size) <= BITS_PER_LONG ? \
- ((off) + (__scanbit((*(unsigned long *)addr) >> (off),(size)-(off)))) : \
- find_next_bit(addr,size,off)))
-
-#define find_next_zero_bit(addr,size,off) \
-((__builtin_constant_p(size) && (size) <= BITS_PER_LONG ? \
- ((off)+(__scanbit(~(((*(unsigned long *)addr)) >> (off)),(size)-(off)))) : \
- find_next_zero_bit(addr,size,off)))
-
-#define find_first_bit(addr, size) \
- ((__builtin_constant_p((size)) && (size) <= BITS_PER_LONG \
- ? (__scanbit(*(unsigned long *)(addr), (size))) \
- : find_first_bit((addr), (size))))
-
-#define find_first_zero_bit(addr, size) \
- ((__builtin_constant_p((size)) && (size) <= BITS_PER_LONG \
- ? (__scanbit(~*(unsigned long *)(addr), (size))) \
- : find_first_zero_bit((addr), (size))))
-
-static inline void set_bit_string(unsigned long *bitmap, unsigned long i,
- int len)
-{
- unsigned long end = i + len;
- while (i < end) {
- __set_bit(i, bitmap);
- i++;
- }
-}
-
-/**
- * ffz - find first zero in word.
- * @word: The word to search
- *
- * Undefined if no zero exists, so code should check against ~0UL first.
- */
-static inline unsigned long ffz(unsigned long word)
-{
- __asm__("bsfq %1,%0"
- :"=r" (word)
- :"r" (~word));
- return word;
-}
-
-/**
- * __ffs - find first bit in word.
- * @word: The word to search
- *
- * Undefined if no bit exists, so code should check against 0 first.
- */
-static inline unsigned long __ffs(unsigned long word)
-{
- __asm__("bsfq %1,%0"
- :"=r" (word)
- :"rm" (word));
- return word;
-}
-
-/*
- * __fls: find last bit set.
- * @word: The word to search
- *
- * Undefined if no zero exists, so code should check against ~0UL first.
- */
-static inline unsigned long __fls(unsigned long word)
-{
- __asm__("bsrq %1,%0"
- :"=r" (word)
- :"rm" (word));
- return word;
-}
-
-#ifdef __KERNEL__
-
-#include <asm-generic/bitops/sched.h>
-
-/**
- * ffs - find first bit set
- * @x: the word to search
- *
- * This is defined the same way as
- * the libc and compiler builtin ffs routines, therefore
- * differs in spirit from the above ffz (man ffs).
- */
-static inline int ffs(int x)
-{
- int r;
-
- __asm__("bsfl %1,%0\n\t"
- "cmovzl %2,%0"
- : "=r" (r) : "rm" (x), "r" (-1));
- return r+1;
-}
-
-/**
- * fls64 - find last bit set in 64 bit word
- * @x: the word to search
- *
- * This is defined the same way as fls.
- */
-static inline int fls64(__u64 x)
-{
- if (x == 0)
- return 0;
- return __fls(x) + 1;
-}
-
-/**
- * fls - find last bit set
- * @x: the word to search
- *
- * This is defined the same way as ffs.
- */
-static inline int fls(int x)
-{
- int r;
-
- __asm__("bsrl %1,%0\n\t"
- "cmovzl %2,%0"
- : "=&r" (r) : "rm" (x), "rm" (-1));
- return r+1;
-}
-
-#define ARCH_HAS_FAST_MULTIPLIER 1
-
-#include <asm-generic/bitops/hweight.h>
-
-#endif /* __KERNEL__ */
-
-#ifdef __KERNEL__
-
-#include <asm-generic/bitops/ext2-non-atomic.h>
-
-#define ext2_set_bit_atomic(lock, nr, addr) \
- test_and_set_bit((nr), (unsigned long *)(addr))
-#define ext2_clear_bit_atomic(lock, nr, addr) \
- test_and_clear_bit((nr), (unsigned long *)(addr))
-
-#include <asm-generic/bitops/minix.h>
-
-#endif /* __KERNEL__ */
-
-#endif /* _X86_64_BITOPS_H */
diff --git a/include/linux/bitops.h b/include/linux/bitops.h
index 40d5473..48bde60 100644
--- a/include/linux/bitops.h
+++ b/include/linux/bitops.h
@@ -112,4 +112,144 @@
return fls64(l);
}
+#ifdef __KERNEL__
+#ifdef CONFIG_GENERIC_FIND_FIRST_BIT
+extern unsigned long __find_first_bit(const unsigned long *addr,
+ unsigned long size);
+
+/**
+ * find_first_bit - find the first set bit in a memory region
+ * @addr: The address to start the search at
+ * @size: The maximum size to search
+ *
+ * Returns the bit number of the first set bit.
+ */
+static __always_inline unsigned long
+find_first_bit(const unsigned long *addr, unsigned long size)
+{
+ /* Avoid a function call if the bitmap size is a constant */
+ /* and not bigger than BITS_PER_LONG. */
+
+ /* insert a sentinel so that __ffs returns size if there */
+ /* are no set bits in the bitmap */
+ if (__builtin_constant_p(size) && (size < BITS_PER_LONG))
+ return __ffs((*addr) | (1ul << size));
+
+ /* the result of __ffs(0) is undefined, so it needs to be */
+ /* handled separately */
+ if (__builtin_constant_p(size) && (size == BITS_PER_LONG))
+ return ((*addr) == 0) ? BITS_PER_LONG : __ffs(*addr);
+
+ /* size is not constant or too big */
+ return __find_first_bit(addr, size);
+}
+
+extern unsigned long __find_first_zero_bit(const unsigned long *addr,
+ unsigned long size);
+
+/**
+ * find_first_zero_bit - find the first cleared bit in a memory region
+ * @addr: The address to start the search at
+ * @size: The maximum size to search
+ *
+ * Returns the bit number of the first cleared bit.
+ */
+static __always_inline unsigned long
+find_first_zero_bit(const unsigned long *addr, unsigned long size)
+{
+ /* Avoid a function call if the bitmap size is a constant */
+ /* and not bigger than BITS_PER_LONG. */
+
+ /* insert a sentinel so that __ffs returns size if there */
+ /* are no set bits in the bitmap */
+ if (__builtin_constant_p(size) && (size < BITS_PER_LONG)) {
+ return __ffs(~(*addr) | (1ul << size));
+ }
+
+ /* the result of __ffs(0) is undefined, so it needs to be */
+ /* handled separately */
+ if (__builtin_constant_p(size) && (size == BITS_PER_LONG))
+ return (~(*addr) == 0) ? BITS_PER_LONG : __ffs(~(*addr));
+
+ /* size is not constant or too big */
+ return __find_first_zero_bit(addr, size);
+}
+#endif /* CONFIG_GENERIC_FIND_FIRST_BIT */
+
+#ifdef CONFIG_GENERIC_FIND_NEXT_BIT
+extern unsigned long __find_next_bit(const unsigned long *addr,
+ unsigned long size, unsigned long offset);
+
+/**
+ * find_next_bit - find the next set bit in a memory region
+ * @addr: The address to base the search on
+ * @offset: The bitnumber to start searching at
+ * @size: The bitmap size in bits
+ */
+static __always_inline unsigned long
+find_next_bit(const unsigned long *addr, unsigned long size,
+ unsigned long offset)
+{
+ unsigned long value;
+
+ /* Avoid a function call if the bitmap size is a constant */
+ /* and not bigger than BITS_PER_LONG. */
+
+ /* insert a sentinel so that __ffs returns size if there */
+ /* are no set bits in the bitmap */
+ if (__builtin_constant_p(size) && (size < BITS_PER_LONG)) {
+ value = (*addr) & ((~0ul) << offset);
+ value |= (1ul << size);
+ return __ffs(value);
+ }
+
+ /* the result of __ffs(0) is undefined, so it needs to be */
+ /* handled separately */
+ if (__builtin_constant_p(size) && (size == BITS_PER_LONG)) {
+ value = (*addr) & ((~0ul) << offset);
+ return (value == 0) ? BITS_PER_LONG : __ffs(value);
+ }
+
+ /* size is not constant or too big */
+ return __find_next_bit(addr, size, offset);
+}
+
+extern unsigned long __find_next_zero_bit(const unsigned long *addr,
+ unsigned long size, unsigned long offset);
+
+/**
+ * find_next_zero_bit - find the next cleared bit in a memory region
+ * @addr: The address to base the search on
+ * @offset: The bitnumber to start searching at
+ * @size: The bitmap size in bits
+ */
+static __always_inline unsigned long
+find_next_zero_bit(const unsigned long *addr, unsigned long size,
+ unsigned long offset)
+{
+ unsigned long value;
+
+ /* Avoid a function call if the bitmap size is a constant */
+ /* and not bigger than BITS_PER_LONG. */
+
+ /* insert a sentinel so that __ffs returns size if there */
+ /* are no set bits in the bitmap */
+ if (__builtin_constant_p(size) && (size < BITS_PER_LONG)) {
+ value = (~(*addr)) & ((~0ul) << offset);
+ value |= (1ul << size);
+ return __ffs(value);
+ }
+
+ /* the result of __ffs(0) is undefined, so it needs to be */
+ /* handled separately */
+ if (__builtin_constant_p(size) && (size == BITS_PER_LONG)) {
+ value = (~(*addr)) & ((~0ul) << offset);
+ return (value == 0) ? BITS_PER_LONG : __ffs(value);
+ }
+
+ /* size is not constant or too big */
+ return __find_next_zero_bit(addr, size, offset);
+}
+#endif /* CONFIG_GENERIC_FIND_NEXT_BIT */
+#endif /* __KERNEL__ */
#endif
diff --git a/include/linux/ide.h b/include/linux/ide.h
index f20410d..f0af504 100644
--- a/include/linux/ide.h
+++ b/include/linux/ide.h
@@ -387,6 +387,43 @@
struct ide_port_info;
+struct ide_port_ops {
+ /* host specific initialization of devices on a port */
+ void (*port_init_devs)(struct hwif_s *);
+ /* routine to program host for PIO mode */
+ void (*set_pio_mode)(ide_drive_t *, const u8);
+ /* routine to program host for DMA mode */
+ void (*set_dma_mode)(ide_drive_t *, const u8);
+ /* tweaks hardware to select drive */
+ void (*selectproc)(ide_drive_t *);
+ /* chipset polling based on hba specifics */
+ int (*reset_poll)(ide_drive_t *);
+ /* chipset specific changes to default for device-hba resets */
+ void (*pre_reset)(ide_drive_t *);
+ /* routine to reset controller after a disk reset */
+ void (*resetproc)(ide_drive_t *);
+ /* special host masking for drive selection */
+ void (*maskproc)(ide_drive_t *, int);
+ /* check host's drive quirk list */
+ void (*quirkproc)(ide_drive_t *);
+
+ u8 (*mdma_filter)(ide_drive_t *);
+ u8 (*udma_filter)(ide_drive_t *);
+
+ u8 (*cable_detect)(struct hwif_s *);
+};
+
+struct ide_dma_ops {
+ void (*dma_host_set)(struct ide_drive_s *, int);
+ int (*dma_setup)(struct ide_drive_s *);
+ void (*dma_exec_cmd)(struct ide_drive_s *, u8);
+ void (*dma_start)(struct ide_drive_s *);
+ int (*dma_end)(struct ide_drive_s *);
+ int (*dma_test_irq)(struct ide_drive_s *);
+ void (*dma_lost_irq)(struct ide_drive_s *);
+ void (*dma_timeout)(struct ide_drive_s *);
+};
+
typedef struct hwif_s {
struct hwif_s *next; /* for linked-list in ide_hwgroup_t */
struct hwif_s *mate; /* other hwif from same PCI chip */
@@ -420,38 +457,12 @@
struct device *dev;
- const struct ide_port_info *cds; /* chipset device struct */
-
ide_ack_intr_t *ack_intr;
void (*rw_disk)(ide_drive_t *, struct request *);
-#if 0
- ide_hwif_ops_t *hwifops;
-#else
- /* host specific initialization of devices on a port */
- void (*port_init_devs)(struct hwif_s *);
- /* routine to program host for PIO mode */
- void (*set_pio_mode)(ide_drive_t *, const u8);
- /* routine to program host for DMA mode */
- void (*set_dma_mode)(ide_drive_t *, const u8);
- /* tweaks hardware to select drive */
- void (*selectproc)(ide_drive_t *);
- /* chipset polling based on hba specifics */
- int (*reset_poll)(ide_drive_t *);
- /* chipset specific changes to default for device-hba resets */
- void (*pre_reset)(ide_drive_t *);
- /* routine to reset controller after a disk reset */
- void (*resetproc)(ide_drive_t *);
- /* special host masking for drive selection */
- void (*maskproc)(ide_drive_t *, int);
- /* check host's drive quirk list */
- void (*quirkproc)(ide_drive_t *);
-#endif
- u8 (*mdma_filter)(ide_drive_t *);
- u8 (*udma_filter)(ide_drive_t *);
-
- u8 (*cable_detect)(struct hwif_s *);
+ const struct ide_port_ops *port_ops;
+ const struct ide_dma_ops *dma_ops;
void (*ata_input_data)(ide_drive_t *, void *, u32);
void (*ata_output_data)(ide_drive_t *, void *, u32);
@@ -459,15 +470,7 @@
void (*atapi_input_bytes)(ide_drive_t *, void *, u32);
void (*atapi_output_bytes)(ide_drive_t *, void *, u32);
- void (*dma_host_set)(ide_drive_t *, int);
- int (*dma_setup)(ide_drive_t *);
- void (*dma_exec_cmd)(ide_drive_t *, u8);
- void (*dma_start)(ide_drive_t *);
- int (*ide_dma_end)(ide_drive_t *drive);
- int (*ide_dma_test_irq)(ide_drive_t *drive);
void (*ide_dma_clear_irq)(ide_drive_t *drive);
- void (*dma_lost_irq)(ide_drive_t *drive);
- void (*dma_timeout)(ide_drive_t *drive);
void (*OUTB)(u8 addr, unsigned long port);
void (*OUTBSYNC)(ide_drive_t *drive, u8 addr, unsigned long port);
@@ -514,7 +517,6 @@
unsigned long extra_base; /* extra addr for dma ports */
unsigned extra_ports; /* number of extra dma ports */
- unsigned noprobe : 1; /* don't probe for this interface */
unsigned present : 1; /* this interface exists */
unsigned serialized : 1; /* serialized all channel operation */
unsigned sharing_irq: 1; /* 1 = sharing irq with another hwif */
@@ -1009,10 +1011,15 @@
void ide_setup_pci_noise(struct pci_dev *, const struct ide_port_info *);
#ifdef CONFIG_BLK_DEV_IDEDMA_PCI
-void ide_hwif_setup_dma(ide_hwif_t *, const struct ide_port_info *);
+int ide_pci_set_master(struct pci_dev *, const char *);
+unsigned long ide_pci_dma_base(ide_hwif_t *, const struct ide_port_info *);
+int ide_hwif_setup_dma(ide_hwif_t *, const struct ide_port_info *);
#else
-static inline void ide_hwif_setup_dma(ide_hwif_t *hwif,
- const struct ide_port_info *d) { }
+static inline int ide_hwif_setup_dma(ide_hwif_t *hwif,
+ const struct ide_port_info *d)
+{
+ return -EINVAL;
+}
#endif
extern void default_hwif_iops(ide_hwif_t *);
@@ -1084,6 +1091,8 @@
/* unmask IRQs */
IDE_HFLAG_UNMASK_IRQS = (1 << 25),
IDE_HFLAG_ABUSE_SET_DMA_MODE = (1 << 26),
+ /* serialize ports if DMA is possible (for sl82c105) */
+ IDE_HFLAG_SERIALIZE_DMA = (1 << 27),
/* force host out of "simplex" mode */
IDE_HFLAG_CLEAR_SIMPLEX = (1 << 28),
/* DSC overlap is unsupported */
@@ -1105,10 +1114,14 @@
unsigned int (*init_chipset)(struct pci_dev *, const char *);
void (*init_iops)(ide_hwif_t *);
void (*init_hwif)(ide_hwif_t *);
- void (*init_dma)(ide_hwif_t *, unsigned long);
+ int (*init_dma)(ide_hwif_t *,
+ const struct ide_port_info *);
+
+ const struct ide_port_ops *port_ops;
+ const struct ide_dma_ops *dma_ops;
+
ide_pci_enablebit_t enablebits[2];
hwif_chipset_t chipset;
- u8 extra;
u32 host_flags;
u8 pio_mask;
u8 swdma_mask;
@@ -1155,13 +1168,16 @@
#ifdef CONFIG_BLK_DEV_IDEDMA_SFF
extern int ide_build_dmatable(ide_drive_t *, struct request *);
-extern int ide_release_dma(ide_hwif_t *);
-extern void ide_setup_dma(ide_hwif_t *, unsigned long);
+int ide_allocate_dma_engine(ide_hwif_t *);
+void ide_release_dma_engine(ide_hwif_t *);
+void ide_setup_dma(ide_hwif_t *, unsigned long);
void ide_dma_host_set(ide_drive_t *, int);
extern int ide_dma_setup(ide_drive_t *);
+void ide_dma_exec_cmd(ide_drive_t *, u8);
extern void ide_dma_start(ide_drive_t *);
extern int __ide_dma_end(ide_drive_t *);
+int ide_dma_test_irq(ide_drive_t *);
extern void ide_dma_lost_irq(ide_drive_t *);
extern void ide_dma_timeout(ide_drive_t *);
#endif /* CONFIG_BLK_DEV_IDEDMA_SFF */
@@ -1179,7 +1195,7 @@
#endif /* CONFIG_BLK_DEV_IDEDMA */
#ifndef CONFIG_BLK_DEV_IDEDMA_SFF
-static inline void ide_release_dma(ide_hwif_t *drive) {;}
+static inline void ide_release_dma_engine(ide_hwif_t *hwif) { ; }
#endif
#ifdef CONFIG_BLK_DEV_IDEACPI
@@ -1199,8 +1215,6 @@
#endif
void ide_remove_port_from_hwgroup(ide_hwif_t *);
-extern int ide_hwif_request_regions(ide_hwif_t *hwif);
-extern void ide_hwif_release_regions(ide_hwif_t* hwif);
void ide_unregister(unsigned int);
void ide_register_region(struct gendisk *);
@@ -1210,6 +1224,7 @@
int ide_device_add_all(u8 *idx, const struct ide_port_info *);
int ide_device_add(u8 idx[4], const struct ide_port_info *);
+int ide_legacy_device_add(const struct ide_port_info *, unsigned long);
void ide_port_unregister_devices(ide_hwif_t *);
void ide_port_scan(ide_hwif_t *);
diff --git a/lib/Kconfig b/lib/Kconfig
index 2d53dc0..8cc8e87 100644
--- a/lib/Kconfig
+++ b/lib/Kconfig
@@ -7,6 +7,12 @@
config BITREVERSE
tristate
+config GENERIC_FIND_FIRST_BIT
+ def_bool n
+
+config GENERIC_FIND_NEXT_BIT
+ def_bool n
+
config CRC_CCITT
tristate "CRC-CCITT functions"
help
diff --git a/lib/Makefile b/lib/Makefile
index bf8000f..2d7001b 100644
--- a/lib/Makefile
+++ b/lib/Makefile
@@ -29,6 +29,7 @@
obj-$(CONFIG_DEBUG_SPINLOCK) += spinlock_debug.o
lib-$(CONFIG_RWSEM_GENERIC_SPINLOCK) += rwsem-spinlock.o
lib-$(CONFIG_RWSEM_XCHGADD_ALGORITHM) += rwsem.o
+lib-$(CONFIG_GENERIC_FIND_FIRST_BIT) += find_next_bit.o
lib-$(CONFIG_GENERIC_FIND_NEXT_BIT) += find_next_bit.o
obj-$(CONFIG_GENERIC_HWEIGHT) += hweight.o
obj-$(CONFIG_LOCK_KERNEL) += kernel_lock.o
diff --git a/lib/find_next_bit.c b/lib/find_next_bit.c
index 78ccd73..d3f5784 100644
--- a/lib/find_next_bit.c
+++ b/lib/find_next_bit.c
@@ -16,14 +16,12 @@
#define BITOP_WORD(nr) ((nr) / BITS_PER_LONG)
-/**
- * find_next_bit - find the next set bit in a memory region
- * @addr: The address to base the search on
- * @offset: The bitnumber to start searching at
- * @size: The maximum size to search
+#ifdef CONFIG_GENERIC_FIND_NEXT_BIT
+/*
+ * Find the next set bit in a memory region.
*/
-unsigned long find_next_bit(const unsigned long *addr, unsigned long size,
- unsigned long offset)
+unsigned long __find_next_bit(const unsigned long *addr,
+ unsigned long size, unsigned long offset)
{
const unsigned long *p = addr + BITOP_WORD(offset);
unsigned long result = offset & ~(BITS_PER_LONG-1);
@@ -60,15 +58,14 @@
found_middle:
return result + __ffs(tmp);
}
-
-EXPORT_SYMBOL(find_next_bit);
+EXPORT_SYMBOL(__find_next_bit);
/*
* This implementation of find_{first,next}_zero_bit was stolen from
* Linus' asm-alpha/bitops.h.
*/
-unsigned long find_next_zero_bit(const unsigned long *addr, unsigned long size,
- unsigned long offset)
+unsigned long __find_next_zero_bit(const unsigned long *addr,
+ unsigned long size, unsigned long offset)
{
const unsigned long *p = addr + BITOP_WORD(offset);
unsigned long result = offset & ~(BITS_PER_LONG-1);
@@ -105,8 +102,64 @@
found_middle:
return result + ffz(tmp);
}
+EXPORT_SYMBOL(__find_next_zero_bit);
+#endif /* CONFIG_GENERIC_FIND_NEXT_BIT */
-EXPORT_SYMBOL(find_next_zero_bit);
+#ifdef CONFIG_GENERIC_FIND_FIRST_BIT
+/*
+ * Find the first set bit in a memory region.
+ */
+unsigned long __find_first_bit(const unsigned long *addr,
+ unsigned long size)
+{
+ const unsigned long *p = addr;
+ unsigned long result = 0;
+ unsigned long tmp;
+
+ while (size & ~(BITS_PER_LONG-1)) {
+ if ((tmp = *(p++)))
+ goto found;
+ result += BITS_PER_LONG;
+ size -= BITS_PER_LONG;
+ }
+ if (!size)
+ return result;
+
+ tmp = (*p) & (~0UL >> (BITS_PER_LONG - size));
+ if (tmp == 0UL) /* Are any bits set? */
+ return result + size; /* Nope. */
+found:
+ return result + __ffs(tmp);
+}
+EXPORT_SYMBOL(__find_first_bit);
+
+/*
+ * Find the first cleared bit in a memory region.
+ */
+unsigned long __find_first_zero_bit(const unsigned long *addr,
+ unsigned long size)
+{
+ const unsigned long *p = addr;
+ unsigned long result = 0;
+ unsigned long tmp;
+
+ while (size & ~(BITS_PER_LONG-1)) {
+ if (~(tmp = *(p++)))
+ goto found;
+ result += BITS_PER_LONG;
+ size -= BITS_PER_LONG;
+ }
+ if (!size)
+ return result;
+
+ tmp = (*p) | (~0UL << size);
+ if (tmp == ~0UL) /* Are any bits zero? */
+ return result + size; /* Nope. */
+found:
+ return result + ffz(tmp);
+}
+EXPORT_SYMBOL(__find_first_zero_bit);
+#endif /* CONFIG_GENERIC_FIND_FIRST_BIT */
#ifdef __BIG_ENDIAN
diff --git a/scripts/Makefile.modpost b/scripts/Makefile.modpost
index 24b3c8f..a098a04 100644
--- a/scripts/Makefile.modpost
+++ b/scripts/Makefile.modpost
@@ -76,7 +76,7 @@
$(if $(CONFIG_MODULE_SRCVERSION_ALL),-a,) \
$(if $(KBUILD_EXTMOD),-i,-o) $(kernelsymfile) \
$(if $(KBUILD_EXTMOD),-I $(modulesymfile)) \
- $(if $(iKBUILD_EXTRA_SYMBOLS), $(patsubst %, -e %,$(EXTRA_SYMBOLS))) \
+ $(if $(KBUILD_EXTRA_SYMBOLS), $(patsubst %, -e %,$(EXTRA_SYMBOLS))) \
$(if $(KBUILD_EXTMOD),-o $(modulesymfile)) \
$(if $(CONFIG_DEBUG_SECTION_MISMATCH),,-S) \
$(if $(CONFIG_MARKERS),-K $(kernelmarkersfile)) \
diff --git a/scripts/mod/modpost.c b/scripts/mod/modpost.c
index f8b42ab..757294b 100644
--- a/scripts/mod/modpost.c
+++ b/scripts/mod/modpost.c
@@ -1552,10 +1552,10 @@
}
license = get_modinfo(info.modinfo, info.modinfo_len, "license");
- if (!license && !is_vmlinux(modname))
- fatal("modpost: missing MODULE_LICENSE() in %s\n"
- "see include/linux/module.h for "
- "more information\n", modname);
+ if (info.modinfo && !license && !is_vmlinux(modname))
+ warn("modpost: missing MODULE_LICENSE() in %s\n"
+ "see include/linux/module.h for "
+ "more information\n", modname);
while (license) {
if (license_is_gpl_compatible(license))
mod->gpl_compatible = 1;