xHCI: Implement AMD PLL quirk
This patch disable the optional PM feature inside the Hudson3 platform under
the following conditions:
1. If an isochronous device is connected to xHCI port and is active;
2. Optional PM feature that powers down the internal Bus PLL when the link is
in low power state is enabled.
The PM feature needs to be disabled to eliminate PLL startup delays when the
link comes out of low power state. The performance of DMA data transfer could
be impacted if system delay were encountered and in addition to the PLL start
up delays. Disabling the PM would leave room for unpredictable system delays
in order to guarantee uninterrupted data transfer to isochronous audio or
video stream devices that require time sensitive information. If data in an
audio/video stream was interrupted then erratic audio or video performance
may be encountered.
AMD PLL quirk is already implemented in OHCI/EHCI driver. After moving the
quirk code to pci-quirks.c and export them, xHCI driver can call it directly
without having the quirk implementation in itself.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c
index ceea9f3..a10494c 100644
--- a/drivers/usb/host/xhci-pci.c
+++ b/drivers/usb/host/xhci-pci.c
@@ -114,6 +114,10 @@
if (pdev->vendor == PCI_VENDOR_ID_NEC)
xhci->quirks |= XHCI_NEC_HOST;
+ /* AMD PLL quirk */
+ if (pdev->vendor == PCI_VENDOR_ID_AMD && usb_amd_find_chipset_info())
+ xhci->quirks |= XHCI_AMD_PLL_FIX;
+
/* Make sure the HC is halted. */
retval = xhci_halt(xhci);
if (retval)
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index b0b4cc3..7437386 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -619,6 +619,13 @@
/* Only giveback urb when this is the last td in urb */
if (urb_priv->td_cnt == urb_priv->length) {
+ if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) {
+ xhci_to_hcd(xhci)->self.bandwidth_isoc_reqs--;
+ if (xhci_to_hcd(xhci)->self.bandwidth_isoc_reqs == 0) {
+ if (xhci->quirks & XHCI_AMD_PLL_FIX)
+ usb_amd_quirk_pll_enable();
+ }
+ }
usb_hcd_unlink_urb_from_ep(hcd, urb);
xhci_dbg(xhci, "Giveback %s URB %p\n", adjective, urb);
@@ -1565,8 +1572,17 @@
urb_priv->td_cnt++;
/* Giveback the urb when all the tds are completed */
- if (urb_priv->td_cnt == urb_priv->length)
+ if (urb_priv->td_cnt == urb_priv->length) {
ret = 1;
+ if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) {
+ xhci_to_hcd(xhci)->self.bandwidth_isoc_reqs--;
+ if (xhci_to_hcd(xhci)->self.bandwidth_isoc_reqs
+ == 0) {
+ if (xhci->quirks & XHCI_AMD_PLL_FIX)
+ usb_amd_quirk_pll_enable();
+ }
+ }
+ }
}
return ret;
@@ -3153,6 +3169,12 @@
}
}
+ if (xhci_to_hcd(xhci)->self.bandwidth_isoc_reqs == 0) {
+ if (xhci->quirks & XHCI_AMD_PLL_FIX)
+ usb_amd_quirk_pll_disable();
+ }
+ xhci_to_hcd(xhci)->self.bandwidth_isoc_reqs++;
+
giveback_first_trb(xhci, slot_id, ep_index, urb->stream_id,
start_cycle, start_trb);
return 0;
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index c41358e..81b976e 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -550,6 +550,9 @@
del_timer_sync(&xhci->event_ring_timer);
#endif
+ if (xhci->quirks & XHCI_AMD_PLL_FIX)
+ usb_amd_dev_put();
+
xhci_dbg(xhci, "// Disabling event ring interrupts\n");
temp = xhci_readl(xhci, &xhci->op_regs->status);
xhci_writel(xhci, temp & ~STS_EINT, &xhci->op_regs->status);
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index bdb78f5..ba1be6b 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -30,6 +30,7 @@
/* Code sharing between pci-quirks and xhci hcd */
#include "xhci-ext-caps.h"
+#include "pci-quirks.h"
/* xHCI PCI Configuration Registers */
#define XHCI_SBRN_OFFSET (0x60)
@@ -1279,6 +1280,7 @@
#define XHCI_LINK_TRB_QUIRK (1 << 0)
#define XHCI_RESET_EP_QUIRK (1 << 1)
#define XHCI_NEC_HOST (1 << 2)
+#define XHCI_AMD_PLL_FIX (1 << 3)
/* There are two roothubs to keep track of bus suspend info for */
struct xhci_bus_state bus_state[2];
/* Is each xHCI roothub port a USB 3.0, USB 2.0, or USB 1.1 port? */