diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index a48aecc..b5a91ca 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1578,6 +1578,7 @@
 	int
 	default 1024 if ARCH_SHMOBILE || ARCH_TEGRA
 	default 350 if ARCH_U8500
+	default 264 if MACH_H4700
 	default 0
 	help
 	  Maximum number of GPIOs in the system.
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index e0d236d..03646c4 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -81,25 +81,6 @@
 	prompt "Kernel low-level debugging port"
 	depends on DEBUG_LL
 
-	config DEBUG_LL_UART_NONE
-		bool "No low-level debugging UART"
-		help
-		  Say Y here if your platform doesn't provide a UART option
-		  below. This relies on your platform choosing the right UART
-		  definition internally in order for low-level debugging to
-		  work.
-
-	config DEBUG_ICEDCC
-		bool "Kernel low-level debugging via EmbeddedICE DCC channel"
-		help
-		  Say Y here if you want the debug print routines to direct
-		  their output to the EmbeddedICE macrocell's DCC channel using
-		  co-processor 14. This is known to work on the ARM9 style ICE
-		  channel and on the XScale with the PEEDI.
-
-		  Note that the system will appear to hang during boot if there
-		  is nothing connected to read from the DCC.
-
 	config AT91_DEBUG_LL_DBGU0
 		bool "Kernel low-level debugging on rm9200, 9260/9g20, 9261/9g10 and 9rl"
 		depends on HAVE_AT91_DBGU0
@@ -108,20 +89,6 @@
 		bool "Kernel low-level debugging on 9263, 9g45 and cap9"
 		depends on HAVE_AT91_DBGU1
 
-	config DEBUG_FOOTBRIDGE_COM1
-		bool "Kernel low-level debugging messages via footbridge 8250 at PCI COM1"
-		depends on FOOTBRIDGE
-		help
-		  Say Y here if you want the debug print routines to direct
-		  their output to the 8250 at PCI COM1.
-
-	config DEBUG_DC21285_PORT
-		bool "Kernel low-level debugging messages via footbridge serial port"
-		depends on FOOTBRIDGE
-		help
-		  Say Y here if you want the debug print routines to direct
-		  their output to the serial port in the DC21285 (Footbridge).
-
 	config DEBUG_CLPS711X_UART1
 		bool "Kernel low-level debugging messages via UART1"
 		depends on ARCH_CLPS711X
@@ -136,6 +103,20 @@
 		  Say Y here if you want the debug print routines to direct
 		  their output to the second serial port on these devices.
 
+	config DEBUG_DC21285_PORT
+		bool "Kernel low-level debugging messages via footbridge serial port"
+		depends on FOOTBRIDGE
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the serial port in the DC21285 (Footbridge).
+
+	config DEBUG_FOOTBRIDGE_COM1
+		bool "Kernel low-level debugging messages via footbridge 8250 at PCI COM1"
+		depends on FOOTBRIDGE
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the 8250 at PCI COM1.
+
 	config DEBUG_HIGHBANK_UART
 		bool "Kernel low-level debugging messages via Highbank UART"
 		depends on ARCH_HIGHBANK
@@ -206,55 +187,6 @@
 		  Say Y here if you want kernel low-level debugging support
 		  on i.MX6Q.
 
-	config DEBUG_S3C_UART0
-		depends on PLAT_SAMSUNG
-		bool "Use S3C UART 0 for low-level debug"
-		help
-		  Say Y here if you want the debug print routines to direct
-		  their output to UART 0. The port must have been initialised
-		  by the boot-loader before use.
-
-		  The uncompressor code port configuration is now handled
-		  by CONFIG_S3C_LOWLEVEL_UART_PORT.
-
-	config DEBUG_S3C_UART1
-		depends on PLAT_SAMSUNG
-		bool "Use S3C UART 1 for low-level debug"
-		help
-		  Say Y here if you want the debug print routines to direct
-		  their output to UART 1. The port must have been initialised
-		  by the boot-loader before use.
-
-		  The uncompressor code port configuration is now handled
-		  by CONFIG_S3C_LOWLEVEL_UART_PORT.
-
-	config DEBUG_S3C_UART2
-		depends on PLAT_SAMSUNG
-		bool "Use S3C UART 2 for low-level debug"
-		help
-		  Say Y here if you want the debug print routines to direct
-		  their output to UART 2. The port must have been initialised
-		  by the boot-loader before use.
-
-		  The uncompressor code port configuration is now handled
-		  by CONFIG_S3C_LOWLEVEL_UART_PORT.
-
-	config DEBUG_REALVIEW_STD_PORT
-		bool "RealView Default UART"
-		depends on ARCH_REALVIEW
-		help
-		  Say Y here if you want the debug print routines to direct
-		  their output to the serial port on RealView EB, PB11MP, PBA8
-		  and PBX platforms.
-
-	config DEBUG_REALVIEW_PB1176_PORT
-		bool "RealView PB1176 UART"
-		depends on MACH_REALVIEW_PB1176
-		help
-		  Say Y here if you want the debug print routines to direct
-		  their output to the standard serial port on the RealView
-		  PB1176 platform.
-
 	config DEBUG_MSM_UART1
 		bool "Kernel low-level debugging messages via MSM UART1"
 		depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50
@@ -292,6 +224,74 @@
 		  Say Y here if you want the debug print routines to direct
 		  their output to the serial port on MSM 8960 devices.
 
+	config DEBUG_REALVIEW_STD_PORT
+		bool "RealView Default UART"
+		depends on ARCH_REALVIEW
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the serial port on RealView EB, PB11MP, PBA8
+		  and PBX platforms.
+
+	config DEBUG_REALVIEW_PB1176_PORT
+		bool "RealView PB1176 UART"
+		depends on MACH_REALVIEW_PB1176
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the standard serial port on the RealView
+		  PB1176 platform.
+
+	config DEBUG_S3C_UART0
+		depends on PLAT_SAMSUNG
+		bool "Use S3C UART 0 for low-level debug"
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to UART 0. The port must have been initialised
+		  by the boot-loader before use.
+
+		  The uncompressor code port configuration is now handled
+		  by CONFIG_S3C_LOWLEVEL_UART_PORT.
+
+	config DEBUG_S3C_UART1
+		depends on PLAT_SAMSUNG
+		bool "Use S3C UART 1 for low-level debug"
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to UART 1. The port must have been initialised
+		  by the boot-loader before use.
+
+		  The uncompressor code port configuration is now handled
+		  by CONFIG_S3C_LOWLEVEL_UART_PORT.
+
+	config DEBUG_S3C_UART2
+		depends on PLAT_SAMSUNG
+		bool "Use S3C UART 2 for low-level debug"
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to UART 2. The port must have been initialised
+		  by the boot-loader before use.
+
+		  The uncompressor code port configuration is now handled
+		  by CONFIG_S3C_LOWLEVEL_UART_PORT.
+
+	config DEBUG_LL_UART_NONE
+		bool "No low-level debugging UART"
+		help
+		  Say Y here if your platform doesn't provide a UART option
+		  below. This relies on your platform choosing the right UART
+		  definition internally in order for low-level debugging to
+		  work.
+
+	config DEBUG_ICEDCC
+		bool "Kernel low-level debugging via EmbeddedICE DCC channel"
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the EmbeddedICE macrocell's DCC channel using
+		  co-processor 14. This is known to work on the ARM9 style ICE
+		  channel and on the XScale with the PEEDI.
+
+		  Note that the system will appear to hang during boot if there
+		  is nothing connected to read from the DCC.
+
 endchoice
 
 config EARLY_PRINTK
diff --git a/arch/arm/boot/dts/kirkwood-dreamplug.dts b/arch/arm/boot/dts/kirkwood-dreamplug.dts
new file mode 100644
index 0000000..8a5dff8
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-dreamplug.dts
@@ -0,0 +1,25 @@
+/dts-v1/;
+
+/include/ "kirkwood.dtsi"
+
+/ {
+	model = "Globalscale Technologies Dreamplug";
+	compatible = "globalscale,dreamplug-003-ds2001", "globalscale,dreamplug", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+	};
+
+	serial@f1012000 {
+		compatible = "ns16550a";
+		reg = <0xf1012000 0xff>;
+		reg-shift = <2>;
+		interrupts = <33>;
+		clock-frequency = <200000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi
new file mode 100644
index 0000000..771c6bb
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood.dtsi
@@ -0,0 +1,6 @@
+/include/ "skeleton.dtsi"
+
+/ {
+	compatible = "marvell,kirkwood";
+};
+
diff --git a/arch/arm/boot/dts/tegra-paz00.dts b/arch/arm/boot/dts/tegra-paz00.dts
index 825d295..61f3858 100644
--- a/arch/arm/boot/dts/tegra-paz00.dts
+++ b/arch/arm/boot/dts/tegra-paz00.dts
@@ -35,6 +35,11 @@
 
 	i2c@7000d000 {
 		clock-frequency = <400000>;
+
+		adt7461@4c {
+			compatible = "adi,adt7461";
+			reg = <0x4c>;
+		};
 	};
 
 	serial@70006000 {
@@ -74,4 +79,25 @@
 	sdhci@c8000600 {
 		support-8bit;
 	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		power {
+			label = "Power";
+			gpios = <&gpio 79 1>; /* gpio PJ7, active low */
+			linux,code = <116>; /* KEY_POWER */
+			gpio-key,wakeup;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		wifi {
+			label = "wifi-led";
+			gpios = <&gpio 24 0>;
+			linux,default-trigger = "rfkill0";
+		};
+	};
 };
diff --git a/arch/arm/include/asm/system.h b/arch/arm/include/asm/system.h
index e4c96cc..424aa45 100644
--- a/arch/arm/include/asm/system.h
+++ b/arch/arm/include/asm/system.h
@@ -110,6 +110,7 @@
 
 void soft_restart(unsigned long);
 extern void (*arm_pm_restart)(char str, const char *cmd);
+extern void (*arm_pm_idle)(void);
 
 #define UDBG_UNDEFINED	(1 << 0)
 #define UDBG_SYSCALL	(1 << 1)
diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c
index 971d65c..008e7ce 100644
--- a/arch/arm/kernel/process.c
+++ b/arch/arm/kernel/process.c
@@ -61,8 +61,6 @@
 
 static volatile int hlt_counter;
 
-#include <mach/system.h>
-
 void disable_hlt(void)
 {
 	hlt_counter++;
@@ -181,13 +179,17 @@
 EXPORT_SYMBOL_GPL(cpu_idle_wait);
 
 /*
- * This is our default idle handler.  We need to disable
- * interrupts here to ensure we don't miss a wakeup call.
+ * This is our default idle handler.
  */
+
+void (*arm_pm_idle)(void);
+
 static void default_idle(void)
 {
-	if (!need_resched())
-		arch_idle();
+	if (arm_pm_idle)
+		arm_pm_idle();
+	else
+		cpu_do_idle();
 	local_irq_enable();
 }
 
@@ -215,6 +217,10 @@
 				cpu_die();
 #endif
 
+			/*
+			 * We need to disable interrupts here
+			 * to ensure we don't miss a wakeup call.
+			 */
 			local_irq_disable();
 #ifdef CONFIG_PL310_ERRATA_769419
 			wmb();
@@ -222,19 +228,18 @@
 			if (hlt_counter) {
 				local_irq_enable();
 				cpu_relax();
-			} else {
+			} else if (!need_resched()) {
 				stop_critical_timings();
 				if (cpuidle_idle_call())
 					pm_idle();
 				start_critical_timings();
 				/*
-				 * This will eventually be removed - pm_idle
-				 * functions should always return with IRQs
-				 * enabled.
+				 * pm_idle functions must always
+				 * return with IRQs enabled.
 				 */
 				WARN_ON(irqs_disabled());
+			} else
 				local_irq_enable();
-			}
 		}
 		leds_event(led_idle_end);
 		rcu_idle_exit();
diff --git a/arch/arm/mach-at91/at91cap9.c b/arch/arm/mach-at91/at91cap9.c
index a42edc2..8967d75 100644
--- a/arch/arm/mach-at91/at91cap9.c
+++ b/arch/arm/mach-at91/at91cap9.c
@@ -14,6 +14,7 @@
 
 #include <linux/module.h>
 
+#include <asm/proc-fns.h>
 #include <asm/irq.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -313,6 +314,12 @@
 	}
 };
 
+static void at91cap9_idle(void)
+{
+	at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
+	cpu_do_idle();
+}
+
 /* --------------------------------------------------------------------
  *  AT91CAP9 processor initialization
  * -------------------------------------------------------------------- */
@@ -332,6 +339,7 @@
 
 static void __init at91cap9_initialize(void)
 {
+	arm_pm_idle = at91cap9_idle;
 	arm_pm_restart = at91sam9g45_restart;
 	at91_extern_irq = (1 << AT91CAP9_ID_IRQ0) | (1 << AT91CAP9_ID_IRQ1);
 
diff --git a/arch/arm/mach-at91/at91rm9200.c b/arch/arm/mach-at91/at91rm9200.c
index 99c3174..dd6e2de 100644
--- a/arch/arm/mach-at91/at91rm9200.c
+++ b/arch/arm/mach-at91/at91rm9200.c
@@ -289,6 +289,15 @@
 	}
 };
 
+static void at91rm9200_idle(void)
+{
+	/*
+	 * Disable the processor clock.  The processor will be automatically
+	 * re-enabled by an interrupt or by a reset.
+	 */
+	at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
+}
+
 static void at91rm9200_restart(char mode, const char *cmd)
 {
 	/*
@@ -314,6 +323,7 @@
 
 static void __init at91rm9200_initialize(void)
 {
+	arm_pm_idle = at91rm9200_idle;
 	arm_pm_restart = at91rm9200_restart;
 	at91_extern_irq = (1 << AT91RM9200_ID_IRQ0) | (1 << AT91RM9200_ID_IRQ1)
 			| (1 << AT91RM9200_ID_IRQ2) | (1 << AT91RM9200_ID_IRQ3)
diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c
index d4036ba..9ac8c6f 100644
--- a/arch/arm/mach-at91/at91sam9260.c
+++ b/arch/arm/mach-at91/at91sam9260.c
@@ -12,6 +12,7 @@
 
 #include <linux/module.h>
 
+#include <asm/proc-fns.h>
 #include <asm/irq.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -328,8 +329,15 @@
 	at91sam9_ioremap_smc(0, AT91SAM9260_BASE_SMC);
 }
 
+static void at91sam9260_idle(void)
+{
+	at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
+	cpu_do_idle();
+}
+
 static void __init at91sam9260_initialize(void)
 {
+	arm_pm_idle = at91sam9260_idle;
 	arm_pm_restart = at91sam9_alt_restart;
 	at91_extern_irq = (1 << AT91SAM9260_ID_IRQ0) | (1 << AT91SAM9260_ID_IRQ1)
 			| (1 << AT91SAM9260_ID_IRQ2);
diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c
index 023c2ff..ab76868 100644
--- a/arch/arm/mach-at91/at91sam9261.c
+++ b/arch/arm/mach-at91/at91sam9261.c
@@ -12,6 +12,7 @@
 
 #include <linux/module.h>
 
+#include <asm/proc-fns.h>
 #include <asm/irq.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -286,8 +287,15 @@
 	at91sam9_ioremap_smc(0, AT91SAM9261_BASE_SMC);
 }
 
+static void at91sam9261_idle(void)
+{
+	at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
+	cpu_do_idle();
+}
+
 static void __init at91sam9261_initialize(void)
 {
+	arm_pm_idle = at91sam9261_idle;
 	arm_pm_restart = at91sam9_alt_restart;
 	at91_extern_irq = (1 << AT91SAM9261_ID_IRQ0) | (1 << AT91SAM9261_ID_IRQ1)
 			| (1 << AT91SAM9261_ID_IRQ2);
diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c
index 75e876c..247ab63 100644
--- a/arch/arm/mach-at91/at91sam9263.c
+++ b/arch/arm/mach-at91/at91sam9263.c
@@ -12,6 +12,7 @@
 
 #include <linux/module.h>
 
+#include <asm/proc-fns.h>
 #include <asm/irq.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -307,8 +308,15 @@
 	at91sam9_ioremap_smc(1, AT91SAM9263_BASE_SMC1);
 }
 
+static void at91sam9263_idle(void)
+{
+	at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
+	cpu_do_idle();
+}
+
 static void __init at91sam9263_initialize(void)
 {
+	arm_pm_idle = at91sam9263_idle;
 	arm_pm_restart = at91sam9_alt_restart;
 	at91_extern_irq = (1 << AT91SAM9263_ID_IRQ0) | (1 << AT91SAM9263_ID_IRQ1);
 
diff --git a/arch/arm/mach-at91/at91sam9g45.c b/arch/arm/mach-at91/at91sam9g45.c
index 1cb6a96..5b12192 100644
--- a/arch/arm/mach-at91/at91sam9g45.c
+++ b/arch/arm/mach-at91/at91sam9g45.c
@@ -317,6 +317,12 @@
 	}
 };
 
+static void at91sam9g45_idle(void)
+{
+	at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
+	cpu_do_idle();
+}
+
 /* --------------------------------------------------------------------
  *  AT91SAM9G45 processor initialization
  * -------------------------------------------------------------------- */
@@ -337,6 +343,7 @@
 
 static void __init at91sam9g45_initialize(void)
 {
+	arm_pm_idle = at91sam9g45_idle;
 	arm_pm_restart = at91sam9g45_restart;
 	at91_extern_irq = (1 << AT91SAM9G45_ID_IRQ0);
 
diff --git a/arch/arm/mach-at91/at91sam9rl.c b/arch/arm/mach-at91/at91sam9rl.c
index d2c91a8..fd60e22 100644
--- a/arch/arm/mach-at91/at91sam9rl.c
+++ b/arch/arm/mach-at91/at91sam9rl.c
@@ -11,6 +11,7 @@
 
 #include <linux/module.h>
 
+#include <asm/proc-fns.h>
 #include <asm/irq.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -291,8 +292,15 @@
 	at91sam9_ioremap_smc(0, AT91SAM9RL_BASE_SMC);
 }
 
+static void at91sam9rl_idle(void)
+{
+	at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
+	cpu_do_idle();
+}
+
 static void __init at91sam9rl_initialize(void)
 {
+	arm_pm_idle = at91sam9rl_idle;
 	arm_pm_restart = at91sam9_alt_restart;
 	at91_extern_irq = (1 << AT91SAM9RL_ID_IRQ0);
 
diff --git a/arch/arm/mach-at91/at91x40.c b/arch/arm/mach-at91/at91x40.c
index 56ba3bd..0154b7f 100644
--- a/arch/arm/mach-at91/at91x40.c
+++ b/arch/arm/mach-at91/at91x40.c
@@ -13,6 +13,7 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/irq.h>
+#include <asm/proc-fns.h>
 #include <asm/mach/arch.h>
 #include <mach/at91x40.h>
 #include <mach/at91_st.h>
@@ -37,8 +38,19 @@
 	return AT91X40_MASTER_CLOCK;
 }
 
+static void at91x40_idle(void)
+{
+	/*
+	 * Disable the processor clock.  The processor will be automatically
+	 * re-enabled by an interrupt or by a reset.
+	 */
+	at91_sys_write(AT91_PS_CR, AT91_PS_CR_CPU);
+	cpu_do_idle();
+}
+
 void __init at91x40_initialize(unsigned long main_clock)
 {
+	arm_pm_idle = at91x40_idle;
 	at91_extern_irq = (1 << AT91X40_ID_IRQ0) | (1 << AT91X40_ID_IRQ1)
 			| (1 << AT91X40_ID_IRQ2);
 }
diff --git a/arch/arm/mach-at91/include/mach/system.h b/arch/arm/mach-at91/include/mach/system.h
deleted file mode 100644
index cbd64f3..0000000
--- a/arch/arm/mach-at91/include/mach/system.h
+++ /dev/null
@@ -1,50 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/system.h
- *
- *  Copyright (C) 2003 SAN People
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-#include <mach/hardware.h>
-#include <mach/at91_st.h>
-#include <mach/at91_dbgu.h>
-#include <mach/at91_pmc.h>
-
-static inline void arch_idle(void)
-{
-	/*
-	 * Disable the processor clock.  The processor will be automatically
-	 * re-enabled by an interrupt or by a reset.
-	 */
-#ifdef AT91_PS
-	at91_sys_write(AT91_PS_CR, AT91_PS_CR_CPU);
-#else
-	at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
-#endif
-#ifndef CONFIG_CPU_ARM920T
-	/*
-	 * Set the processor (CP15) into 'Wait for Interrupt' mode.
-	 * Post-RM9200 processors need this in conjunction with the above
-	 * to save power when idle.
-	 */
-	cpu_do_idle();
-#endif
-}
-
-#endif
diff --git a/arch/arm/mach-bcmring/core.c b/arch/arm/mach-bcmring/core.c
index 6b67b7e..22e4e0a 100644
--- a/arch/arm/mach-bcmring/core.c
+++ b/arch/arm/mach-bcmring/core.c
@@ -52,27 +52,8 @@
 #include <mach/csp/chipcHw_inline.h>
 #include <mach/csp/tmrHw_reg.h>
 
-#define AMBA_DEVICE(name, initname, base, plat, size)       \
-static struct amba_device name##_device = {     \
-   .dev = {                                     \
-      .coherent_dma_mask = ~0,                  \
-      .init_name = initname,                    \
-      .platform_data = plat                     \
-   },                                           \
-   .res = {                                     \
-      .start = MM_ADDR_IO_##base,               \
-		.end = MM_ADDR_IO_##base + (size) - 1,    \
-      .flags = IORESOURCE_MEM                   \
-   },                                           \
-   .dma_mask = ~0,                              \
-   .irq = {                                     \
-      IRQ_##base                                \
-   }                                            \
-}
-
-
-AMBA_DEVICE(uartA, "uarta", UARTA, NULL, SZ_4K);
-AMBA_DEVICE(uartB, "uartb", UARTB, NULL, SZ_4K);
+static AMBA_APB_DEVICE(uartA, "uarta", MM_ADDR_IO_UARTA, { IRQ_UARTA }, NULL);
+static AMBA_APB_DEVICE(uartB, "uartb", MM_ADDR_IO_UARTB, { IRQ_UARTB }, NULL);
 
 static struct clk pll1_clk = {
 	.name = "PLL1",
diff --git a/arch/arm/mach-bcmring/include/mach/system.h b/arch/arm/mach-bcmring/include/mach/system.h
deleted file mode 100644
index cb78250..0000000
--- a/arch/arm/mach-bcmring/include/mach/system.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/*
- *
- *  Copyright (C) 1999 ARM Limited
- *  Copyright (C) 2000 Deep Blue Solutions Ltd
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-clps711x/common.c b/arch/arm/mach-clps711x/common.c
index ab1711b..8736c1a 100644
--- a/arch/arm/mach-clps711x/common.c
+++ b/arch/arm/mach-clps711x/common.c
@@ -225,3 +225,19 @@
 {
 	soft_restart(0);
 }
+
+static void clps711x_idle(void)
+{
+	clps_writel(1, HALT);
+	__asm__ __volatile__(
+	"mov    r0, r0\n\
+	mov     r0, r0");
+}
+
+static int __init clps711x_idle_init(void)
+{
+	arm_pm_idle = clps711x_idle;
+	return 0;
+}
+
+arch_initcall(clps711x_idle_init);
diff --git a/arch/arm/mach-clps711x/include/mach/system.h b/arch/arm/mach-clps711x/include/mach/system.h
deleted file mode 100644
index 23d6ef8..0000000
--- a/arch/arm/mach-clps711x/include/mach/system.h
+++ /dev/null
@@ -1,35 +0,0 @@
-/*
- *  arch/arm/mach-clps711x/include/mach/system.h
- *
- *  Copyright (C) 2000 Deep Blue Solutions Ltd
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-#include <linux/io.h>
-#include <mach/hardware.h>
-#include <asm/hardware/clps7111.h>
-
-static inline void arch_idle(void)
-{
-	clps_writel(1, HALT);
-	__asm__ __volatile__(
-	"mov	r0, r0\n\
-	mov	r0, r0");
-}
-
-#endif
diff --git a/arch/arm/mach-cns3xxx/include/mach/system.h b/arch/arm/mach-cns3xxx/include/mach/system.h
deleted file mode 100644
index 9e56b7d..0000000
--- a/arch/arm/mach-cns3xxx/include/mach/system.h
+++ /dev/null
@@ -1,25 +0,0 @@
-/*
- * Copyright 2000 Deep Blue Solutions Ltd
- * Copyright 2003 ARM Limited
- * Copyright 2008 Cavium Networks
- *
- * This file is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License, Version 2, as
- * published by the Free Software Foundation.
- */
-
-#ifndef __MACH_SYSTEM_H
-#define __MACH_SYSTEM_H
-
-#include <asm/proc-fns.h>
-
-static inline void arch_idle(void)
-{
-	/*
-	 * This should do all the clock switching
-	 * and wait for interrupt tricks
-	 */
-	cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-davinci/include/mach/system.h b/arch/arm/mach-davinci/include/mach/system.h
deleted file mode 100644
index fcb7a01..0000000
--- a/arch/arm/mach-davinci/include/mach/system.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/*
- * DaVinci system defines
- *
- * Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com>
- *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-#include <mach/common.h>
-
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
-
-#endif /* __ASM_ARCH_SYSTEM_H */
diff --git a/arch/arm/mach-dove/include/mach/system.h b/arch/arm/mach-dove/include/mach/system.h
deleted file mode 100644
index 3027954..0000000
--- a/arch/arm/mach-dove/include/mach/system.h
+++ /dev/null
@@ -1,17 +0,0 @@
-/*
- * arch/arm/mach-dove/include/mach/system.h
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-ebsa110/core.c b/arch/arm/mach-ebsa110/core.c
index 294aad0..804c912 100644
--- a/arch/arm/mach-ebsa110/core.c
+++ b/arch/arm/mach-ebsa110/core.c
@@ -271,8 +271,33 @@
 	&am79c961_device,
 };
 
+/*
+ * EBSA110 idling methodology:
+ *
+ * We can not execute the "wait for interrupt" instruction since that
+ * will stop our MCLK signal (which provides the clock for the glue
+ * logic, and therefore the timer interrupt).
+ *
+ * Instead, we spin, polling the IRQ_STAT register for the occurrence
+ * of any interrupt with core clock down to the memory clock.
+ */
+static void ebsa110_idle(void)
+{
+	const char *irq_stat = (char *)0xff000000;
+
+	/* disable clock switching */
+	asm volatile ("mcr p15, 0, ip, c15, c2, 2" : : : "cc");
+
+	/* wait for an interrupt to occur */
+	while (!*irq_stat);
+
+	/* enable clock switching */
+	asm volatile ("mcr p15, 0, ip, c15, c1, 2" : : : "cc");
+}
+
 static int __init ebsa110_init(void)
 {
+	arm_pm_idle = ebsa110_idle;
 	return platform_add_devices(ebsa110_devices, ARRAY_SIZE(ebsa110_devices));
 }
 
diff --git a/arch/arm/mach-ebsa110/include/mach/system.h b/arch/arm/mach-ebsa110/include/mach/system.h
deleted file mode 100644
index 2e4af65..0000000
--- a/arch/arm/mach-ebsa110/include/mach/system.h
+++ /dev/null
@@ -1,37 +0,0 @@
-/*
- *  arch/arm/mach-ebsa110/include/mach/system.h
- *
- *  Copyright (C) 1996-2000 Russell King.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-/*
- * EBSA110 idling methodology:
- *
- * We can not execute the "wait for interrupt" instruction since that
- * will stop our MCLK signal (which provides the clock for the glue
- * logic, and therefore the timer interrupt).
- *
- * Instead, we spin, polling the IRQ_STAT register for the occurrence
- * of any interrupt with core clock down to the memory clock.
- */
-static inline void arch_idle(void)
-{
-	const char *irq_stat = (char *)0xff000000;
-
-	/* disable clock switching */
-	asm volatile ("mcr p15, 0, ip, c15, c2, 2" : : : "cc");
-
-	/* wait for an interrupt to occur */
-	while (!*irq_stat);
-
-	/* enable clock switching */
-	asm volatile ("mcr p15, 0, ip, c15, c1, 2" : : : "cc");
-}
-
-#endif
diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c
index 24203f9..903edb0 100644
--- a/arch/arm/mach-ep93xx/core.c
+++ b/arch/arm/mach-ep93xx/core.c
@@ -279,48 +279,14 @@
 	.set_mctrl	= ep93xx_uart_set_mctrl,
 };
 
-static struct amba_device uart1_device = {
-	.dev		= {
-		.init_name	= "apb:uart1",
-		.platform_data	= &ep93xx_uart_data,
-	},
-	.res		= {
-		.start	= EP93XX_UART1_PHYS_BASE,
-		.end	= EP93XX_UART1_PHYS_BASE + 0x0fff,
-		.flags	= IORESOURCE_MEM,
-	},
-	.irq		= { IRQ_EP93XX_UART1, NO_IRQ },
-	.periphid	= 0x00041010,
-};
+static AMBA_APB_DEVICE(uart1, "apb:uart1", 0x00041010, EP93XX_UART1_PHYS_BASE,
+	{ IRQ_EP93XX_UART1 }, &ep93xx_uart_data);
 
-static struct amba_device uart2_device = {
-	.dev		= {
-		.init_name	= "apb:uart2",
-		.platform_data	= &ep93xx_uart_data,
-	},
-	.res		= {
-		.start	= EP93XX_UART2_PHYS_BASE,
-		.end	= EP93XX_UART2_PHYS_BASE + 0x0fff,
-		.flags	= IORESOURCE_MEM,
-	},
-	.irq		= { IRQ_EP93XX_UART2, NO_IRQ },
-	.periphid	= 0x00041010,
-};
+static AMBA_APB_DEVICE(uart2, "apb:uart2", 0x00041010, EP93XX_UART2_PHYS_BASE,
+	{ IRQ_EP93XX_UART2 }, &ep93xx_uart_data);
 
-static struct amba_device uart3_device = {
-	.dev		= {
-		.init_name	= "apb:uart3",
-		.platform_data	= &ep93xx_uart_data,
-	},
-	.res		= {
-		.start	= EP93XX_UART3_PHYS_BASE,
-		.end	= EP93XX_UART3_PHYS_BASE + 0x0fff,
-		.flags	= IORESOURCE_MEM,
-	},
-	.irq		= { IRQ_EP93XX_UART3, NO_IRQ },
-	.periphid	= 0x00041010,
-};
-
+static AMBA_APB_DEVICE(uart3, "apb:uart3", 0x00041010, EP93XX_UART3_PHYS_BASE,
+	{ IRQ_EP93XX_UART3 }, &ep93xx_uart_data);
 
 static struct resource ep93xx_rtc_resource[] = {
 	{
diff --git a/arch/arm/mach-ep93xx/include/mach/system.h b/arch/arm/mach-ep93xx/include/mach/system.h
deleted file mode 100644
index b5bec7c..0000000
--- a/arch/arm/mach-ep93xx/include/mach/system.h
+++ /dev/null
@@ -1,7 +0,0 @@
-/*
- * arch/arm/mach-ep93xx/include/mach/system.h
- */
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
diff --git a/arch/arm/mach-exynos/common.c b/arch/arm/mach-exynos/common.c
index c59e188..031c1e5 100644
--- a/arch/arm/mach-exynos/common.c
+++ b/arch/arm/mach-exynos/common.c
@@ -201,14 +201,6 @@
 	},
 };
 
-static void exynos_idle(void)
-{
-	if (!need_resched())
-		cpu_do_idle();
-
-	local_irq_enable();
-}
-
 void exynos4_restart(char mode, const char *cmd)
 {
 	__raw_writel(0x1, S5P_SWRESET);
@@ -467,10 +459,6 @@
 int __init exynos_init(void)
 {
 	printk(KERN_INFO "EXYNOS: Initializing architecture\n");
-
-	/* set idle function */
-	pm_idle = exynos_idle;
-
 	return device_register(&exynos4_dev);
 }
 
diff --git a/arch/arm/mach-exynos/dma.c b/arch/arm/mach-exynos/dma.c
index b10fcd2..91370de 100644
--- a/arch/arm/mach-exynos/dma.c
+++ b/arch/arm/mach-exynos/dma.c
@@ -74,21 +74,8 @@
 	.peri_id = pdma0_peri,
 };
 
-struct amba_device exynos4_device_pdma0 = {
-	.dev = {
-		.init_name = "dma-pl330.0",
-		.dma_mask = &dma_dmamask,
-		.coherent_dma_mask = DMA_BIT_MASK(32),
-		.platform_data = &exynos4_pdma0_pdata,
-	},
-	.res = {
-		.start = EXYNOS4_PA_PDMA0,
-		.end = EXYNOS4_PA_PDMA0 + SZ_4K,
-		.flags = IORESOURCE_MEM,
-	},
-	.irq = {IRQ_PDMA0, NO_IRQ},
-	.periphid = 0x00041330,
-};
+AMBA_AHB_DEVICE(exynos4_pdma0, "dma-pl330.0", 0x00041330, EXYNOS4_PA_PDMA0,
+	{IRQ_PDMA0}, &exynos4_pdma0_pdata);
 
 u8 pdma1_peri[] = {
 	DMACH_PCM0_RX,
@@ -123,21 +110,8 @@
 	.peri_id = pdma1_peri,
 };
 
-struct amba_device exynos4_device_pdma1 = {
-	.dev = {
-		.init_name = "dma-pl330.1",
-		.dma_mask = &dma_dmamask,
-		.coherent_dma_mask = DMA_BIT_MASK(32),
-		.platform_data = &exynos4_pdma1_pdata,
-	},
-	.res = {
-		.start = EXYNOS4_PA_PDMA1,
-		.end = EXYNOS4_PA_PDMA1 + SZ_4K,
-		.flags = IORESOURCE_MEM,
-	},
-	.irq = {IRQ_PDMA1, NO_IRQ},
-	.periphid = 0x00041330,
-};
+AMBA_AHB_DEVICE(exynos4_pdma1,  "dma-pl330.1", 0x00041330, EXYNOS4_PA_PDMA1,
+	{IRQ_PDMA1}, &exynos4_pdma1_pdata);
 
 static int __init exynos4_dma_init(void)
 {
@@ -146,11 +120,11 @@
 
 	dma_cap_set(DMA_SLAVE, exynos4_pdma0_pdata.cap_mask);
 	dma_cap_set(DMA_CYCLIC, exynos4_pdma0_pdata.cap_mask);
-	amba_device_register(&exynos4_device_pdma0, &iomem_resource);
+	amba_device_register(&exynos4_pdma0_device, &iomem_resource);
 
 	dma_cap_set(DMA_SLAVE, exynos4_pdma1_pdata.cap_mask);
 	dma_cap_set(DMA_CYCLIC, exynos4_pdma1_pdata.cap_mask);
-	amba_device_register(&exynos4_device_pdma1, &iomem_resource);
+	amba_device_register(&exynos4_pdma1_device, &iomem_resource);
 
 	return 0;
 }
diff --git a/arch/arm/mach-exynos/include/mach/system.h b/arch/arm/mach-exynos/include/mach/system.h
deleted file mode 100644
index 0063a6d..0000000
--- a/arch/arm/mach-exynos/include/mach/system.h
+++ /dev/null
@@ -1,20 +0,0 @@
-/* linux/arch/arm/mach-exynos4/include/mach/system.h
- *
- * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com
- *
- * EXYNOS4 - system support header
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H __FILE__
-
-static void arch_idle(void)
-{
-	/* nothing here yet */
-}
-#endif /* __ASM_ARCH_SYSTEM_H */
diff --git a/arch/arm/mach-footbridge/include/mach/system.h b/arch/arm/mach-footbridge/include/mach/system.h
deleted file mode 100644
index a174a58..0000000
--- a/arch/arm/mach-footbridge/include/mach/system.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- *  arch/arm/mach-footbridge/include/mach/system.h
- *
- *  Copyright (C) 1996-1999 Russell King.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
diff --git a/arch/arm/mach-gemini/Makefile b/arch/arm/mach-gemini/Makefile
index c5b24b9..7355c0b 100644
--- a/arch/arm/mach-gemini/Makefile
+++ b/arch/arm/mach-gemini/Makefile
@@ -4,7 +4,7 @@
 
 # Object file lists.
 
-obj-y			:= irq.o mm.o time.o devices.o gpio.o
+obj-y			:= irq.o mm.o time.o devices.o gpio.o idle.o
 
 # Board-specific support
 obj-$(CONFIG_MACH_NAS4220B)	+= board-nas4220b.o
diff --git a/arch/arm/mach-gemini/idle.c b/arch/arm/mach-gemini/idle.c
new file mode 100644
index 0000000..92bbd6b
--- /dev/null
+++ b/arch/arm/mach-gemini/idle.c
@@ -0,0 +1,29 @@
+/*
+ * arch/arm/mach-gemini/idle.c
+ */
+
+#include <linux/init.h>
+#include <asm/system.h>
+#include <asm/proc-fns.h>
+
+static void gemini_idle(void)
+{
+	/*
+	 * Because of broken hardware we have to enable interrupts or the CPU
+	 * will never wakeup... Acctualy it is not very good to enable
+	 * interrupts first since scheduler can miss a tick, but there is
+	 * no other way around this. Platforms that needs it for power saving
+	 * should call enable_hlt() in init code, since by default it is
+	 * disabled.
+	 */
+	local_irq_enable();
+	cpu_do_idle();
+}
+
+static int __init gemini_idle_init(void)
+{
+	arm_pm_idle = gemini_idle;
+	return 0;
+}
+
+arch_initcall(gemini_idle_init);
diff --git a/arch/arm/mach-gemini/include/mach/system.h b/arch/arm/mach-gemini/include/mach/system.h
index 4d9c1f8..a33b5a1 100644
--- a/arch/arm/mach-gemini/include/mach/system.h
+++ b/arch/arm/mach-gemini/include/mach/system.h
@@ -14,20 +14,6 @@
 #include <mach/hardware.h>
 #include <mach/global_reg.h>
 
-static inline void arch_idle(void)
-{
-	/*
-	 * Because of broken hardware we have to enable interrupts or the CPU
-	 * will never wakeup... Acctualy it is not very good to enable
-	 * interrupts here since scheduler can miss a tick, but there is
-	 * no other way around this. Platforms that needs it for power saving
-	 * should call enable_hlt() in init code, since by default it is
-	 * disabled.
-	 */
-	local_irq_enable();
-	cpu_do_idle();
-}
-
 static inline void arch_reset(char mode, const char *cmd)
 {
 	__raw_writel(RESET_GLOBAL | RESET_CPU1,
diff --git a/arch/arm/mach-gemini/irq.c b/arch/arm/mach-gemini/irq.c
index 9485a8f..ca70e5f 100644
--- a/arch/arm/mach-gemini/irq.c
+++ b/arch/arm/mach-gemini/irq.c
@@ -73,8 +73,8 @@
 	unsigned int i, mode = 0, level = 0;
 
 	/*
-	 * Disable arch_idle() by default since it is buggy
-	 * For more info see arch/arm/mach-gemini/include/mach/system.h
+	 * Disable the idle handler by default since it is buggy
+	 * For more info see arch/arm/mach-gemini/idle.c
 	 */
 	disable_hlt();
 
diff --git a/arch/arm/mach-h720x/common.c b/arch/arm/mach-h720x/common.c
index f8a2f6b..e756d1a 100644
--- a/arch/arm/mach-h720x/common.c
+++ b/arch/arm/mach-h720x/common.c
@@ -247,3 +247,21 @@
 {
 	CPU_REG (PMU_BASE, PMU_STAT) |= PMU_WARMRESET;
 }
+
+static void h720x__idle(void)
+{
+	CPU_REG (PMU_BASE, PMU_MODE) = PMU_MODE_IDLE;
+	nop();
+	nop();
+	CPU_REG (PMU_BASE, PMU_MODE) = PMU_MODE_RUN;
+	nop();
+	nop();
+}
+
+static int __init h720x_idle_init(void)
+{
+	arm_pm_idle = h720x__idle;
+	return 0;
+}
+
+arch_initcall(h720x_idle_init);
diff --git a/arch/arm/mach-h720x/include/mach/system.h b/arch/arm/mach-h720x/include/mach/system.h
deleted file mode 100644
index 16ac46e..0000000
--- a/arch/arm/mach-h720x/include/mach/system.h
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * arch/arm/mach-h720x/include/mach/system.h
- *
- * Copyright (C) 2001-2002 Jungjun Kim, Hynix Semiconductor Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- * arch/arm/mach-h720x/include/mach/system.h
- *
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-#include <mach/hardware.h>
-
-static void arch_idle(void)
-{
-	CPU_REG (PMU_BASE, PMU_MODE) = PMU_MODE_IDLE;
-	nop();
-	nop();
-	CPU_REG (PMU_BASE, PMU_MODE) = PMU_MODE_RUN;
-	nop();
-	nop();
-}
-
-#endif
diff --git a/arch/arm/mach-highbank/include/mach/system.h b/arch/arm/mach-highbank/include/mach/system.h
deleted file mode 100644
index b1d8b5f..0000000
--- a/arch/arm/mach-highbank/include/mach/system.h
+++ /dev/null
@@ -1,24 +0,0 @@
-/*
- * Copyright 2010-2011 Calxeda, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms and conditions of the GNU General Public License,
- * version 2, as published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program.  If not, see <http://www.gnu.org/licenses/>.
- */
-#ifndef __MACH_SYSTEM_H
-#define __MACH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 4defb97b..96b1f62 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -320,8 +320,10 @@
 	select IMX_HAVE_PLATFORM_IMX_I2C
 	select IMX_HAVE_PLATFORM_IMX_SSI
 	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_MXC_MMC
+	select IMX_HAVE_PLATFORM_MX2_CAMERA
 	select IMX_HAVE_PLATFORM_MXC_EHCI
+	select IMX_HAVE_PLATFORM_MXC_MMC
+	select LEDS_GPIO_REGISTER
 	help
 	  Include support for Visstrim_m10 platform and its different variants.
 	  This includes specific configurations for the board and its
@@ -492,6 +494,7 @@
 	bool "Support mx31moboard platforms (EPFL Mobots group)"
 	select SOC_IMX31
 	select IMX_HAVE_PLATFORM_FSL_USB2_UDC
+	select IMX_HAVE_PLATFORM_IMX2_WDT
 	select IMX_HAVE_PLATFORM_IMX_I2C
 	select IMX_HAVE_PLATFORM_IMX_UART
 	select IMX_HAVE_PLATFORM_IPU_CORE
diff --git a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
index c2766ae..0a1643c 100644
--- a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
+++ b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
@@ -30,6 +30,10 @@
 #include <linux/input.h>
 #include <linux/gpio.h>
 #include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/leds.h>
+#include <linux/memblock.h>
+#include <media/soc_camera.h>
 #include <sound/tlv320aic32x4.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -39,6 +43,8 @@
 
 #include "devices-imx27.h"
 
+#define TVP5150_RSTN (GPIO_PORTC + 18)
+#define TVP5150_PWDN (GPIO_PORTC + 19)
 #define OTG_PHY_CS_GPIO (GPIO_PORTF + 17)
 #define SDHC1_IRQ IRQ_GPIOB(25)
 
@@ -100,8 +106,99 @@
 	PE1_PF_USBOTG_STP,
 	PB23_PF_USB_PWR,
 	PB24_PF_USB_OC,
+	/* CSI */
+	PB10_PF_CSI_D0,
+	PB11_PF_CSI_D1,
+	PB12_PF_CSI_D2,
+	PB13_PF_CSI_D3,
+	PB14_PF_CSI_D4,
+	PB15_PF_CSI_MCLK,
+	PB16_PF_CSI_PIXCLK,
+	PB17_PF_CSI_D5,
+	PB18_PF_CSI_D6,
+	PB19_PF_CSI_D7,
+	PB20_PF_CSI_VSYNC,
+	PB21_PF_CSI_HSYNC,
 };
 
+/* Camera */
+static int visstrim_camera_power(struct device *dev, int on)
+{
+	gpio_set_value(TVP5150_PWDN, on);
+
+	return 0;
+};
+
+static int visstrim_camera_reset(struct device *dev)
+{
+	gpio_set_value(TVP5150_RSTN, 0);
+	ndelay(500);
+	gpio_set_value(TVP5150_RSTN, 1);
+
+	return 0;
+};
+
+static struct i2c_board_info visstrim_i2c_camera =  {
+	I2C_BOARD_INFO("tvp5150", 0x5d),
+};
+
+static struct soc_camera_link iclink_tvp5150 = {
+	.bus_id         = 0,
+	.board_info     = &visstrim_i2c_camera,
+	.i2c_adapter_id = 0,
+	.power = visstrim_camera_power,
+	.reset = visstrim_camera_reset,
+};
+
+static struct mx2_camera_platform_data visstrim_camera = {
+	.flags = MX2_CAMERA_CCIR | MX2_CAMERA_CCIR_INTERLACE |
+			MX2_CAMERA_SWAP16 | MX2_CAMERA_PCLK_SAMPLE_RISING,
+	.clk = 100000,
+};
+
+static phys_addr_t mx2_camera_base __initdata;
+#define MX2_CAMERA_BUF_SIZE SZ_8M
+
+static void __init visstrim_camera_init(void)
+{
+	struct platform_device *pdev;
+	int dma;
+
+	/* Initialize tvp5150 gpios */
+	mxc_gpio_mode(TVP5150_RSTN | GPIO_GPIO | GPIO_OUT);
+	mxc_gpio_mode(TVP5150_PWDN | GPIO_GPIO | GPIO_OUT);
+	gpio_set_value(TVP5150_RSTN, 1);
+	gpio_set_value(TVP5150_PWDN, 0);
+	ndelay(1);
+
+	gpio_set_value(TVP5150_PWDN, 1);
+	ndelay(1);
+	gpio_set_value(TVP5150_RSTN, 0);
+	ndelay(500);
+	gpio_set_value(TVP5150_RSTN, 1);
+	ndelay(200000);
+
+	pdev = imx27_add_mx2_camera(&visstrim_camera);
+	if (IS_ERR(pdev))
+		return;
+
+	dma = dma_declare_coherent_memory(&pdev->dev,
+				mx2_camera_base, mx2_camera_base,
+				MX2_CAMERA_BUF_SIZE,
+				DMA_MEMORY_MAP | DMA_MEMORY_EXCLUSIVE);
+	if (!(dma & DMA_MEMORY_MAP))
+		return;
+}
+
+static void __init visstrim_reserve(void)
+{
+	/* reserve 4 MiB for mx2-camera */
+	mx2_camera_base = memblock_alloc(MX2_CAMERA_BUF_SIZE,
+			MX2_CAMERA_BUF_SIZE);
+	memblock_free(mx2_camera_base, MX2_CAMERA_BUF_SIZE);
+	memblock_remove(mx2_camera_base, MX2_CAMERA_BUF_SIZE);
+}
+
 /* GPIOs used as events for applications */
 static struct gpio_keys_button visstrim_gpio_keys[] = {
 	{
@@ -136,6 +233,35 @@
 	.nbuttons	= ARRAY_SIZE(visstrim_gpio_keys),
 };
 
+/* led */
+static const struct gpio_led visstrim_m10_leds[] __initconst = {
+	{
+		.name = "visstrim:ld0",
+		.default_trigger = "nand-disk",
+		.gpio = (GPIO_PORTC + 29),
+	},
+	{
+		.name = "visstrim:ld1",
+		.default_trigger = "nand-disk",
+		.gpio = (GPIO_PORTC + 24),
+	},
+	{
+		.name = "visstrim:ld2",
+		.default_trigger = "nand-disk",
+		.gpio = (GPIO_PORTC + 28),
+	},
+	{
+		.name = "visstrim:ld3",
+		.default_trigger = "nand-disk",
+		.gpio = (GPIO_PORTC + 25),
+	},
+};
+
+static const struct gpio_led_platform_data visstrim_m10_led_data __initconst = {
+	.leds = visstrim_m10_leds,
+	.num_leds = ARRAY_SIZE(visstrim_m10_leds),
+};
+
 /* Visstrim_SM10 has a microSD slot connected to sdhc1 */
 static int visstrim_m10_sdhc1_init(struct device *dev,
 		irq_handler_t detect_irq, void *data)
@@ -216,6 +342,9 @@
 	{
 		I2C_BOARD_INFO("tlv320aic32x4", 0x18),
 		.platform_data = &visstrim_m10_aic32x4_pdata,
+	},
+	{
+		 I2C_BOARD_INFO("m41t00", 0x68),
 	}
 };
 
@@ -254,15 +383,20 @@
 	imx27_add_imx_ssi(0, &visstrim_m10_ssi_pdata);
 	imx27_add_imx_uart0(&uart_pdata);
 
-	i2c_register_board_info(0, visstrim_m10_i2c_devices,
-				ARRAY_SIZE(visstrim_m10_i2c_devices));
 	imx27_add_imx_i2c(0, &visstrim_m10_i2c_data);
 	imx27_add_imx_i2c(1, &visstrim_m10_i2c_data);
+	i2c_register_board_info(0, visstrim_m10_i2c_devices,
+				ARRAY_SIZE(visstrim_m10_i2c_devices));
+
 	imx27_add_mxc_mmc(0, &visstrim_m10_sdhc_pdata);
 	imx27_add_mxc_ehci_otg(&visstrim_m10_usbotg_pdata);
 	imx27_add_fec(NULL);
 	imx_add_gpio_keys(&visstrim_gpio_keys_platform_data);
 	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
+	platform_device_register_resndata(NULL, "soc-camera-pdrv", 0, NULL, 0,
+				      &iclink_tvp5150, sizeof(iclink_tvp5150));
+	gpio_led_register_device(0, &visstrim_m10_led_data);
+	visstrim_camera_init();
 }
 
 static void __init visstrim_m10_timer_init(void)
@@ -276,6 +410,7 @@
 
 MACHINE_START(IMX27_VISSTRIM_M10, "Vista Silicon Visstrim_M10")
 	.atag_offset = 0x100,
+	.reserve = visstrim_reserve,
 	.map_io = mx27_map_io,
 	.init_early = imx27_init_early,
 	.init_irq = mx27_init_irq,
diff --git a/arch/arm/mach-imx/mach-mx31moboard.c b/arch/arm/mach-imx/mach-mx31moboard.c
index f225262..c0511fb 100644
--- a/arch/arm/mach-imx/mach-mx31moboard.c
+++ b/arch/arm/mach-imx/mach-mx31moboard.c
@@ -530,6 +530,8 @@
 	platform_add_devices(devices, ARRAY_SIZE(devices));
 	gpio_led_register_device(-1, &mx31moboard_led_pdata);
 
+	imx31_add_imx2_wdt(NULL);
+
 	imx31_add_imx_uart0(&uart0_pdata);
 	imx31_add_imx_uart4(&uart4_pdata);
 
@@ -590,7 +592,7 @@
 }
 
 MACHINE_START(MX31MOBOARD, "EPFL Mobots mx31moboard")
-	/* Maintainer: Valentin Longchamp, EPFL Mobots group */
+	/* Maintainer: Philippe Retornaz, EPFL Mobots group */
 	.atag_offset = 0x100,
 	.reserve = mx31moboard_reserve,
 	.map_io = mx31_map_io,
diff --git a/arch/arm/mach-imx/mm-imx3.c b/arch/arm/mach-imx/mm-imx3.c
index 31807d2..8404ee7 100644
--- a/arch/arm/mach-imx/mm-imx3.c
+++ b/arch/arm/mach-imx/mm-imx3.c
@@ -34,31 +34,29 @@
 {
 	unsigned long reg = 0;
 
-	if (!need_resched())
-		__asm__ __volatile__(
-			/* disable I and D cache */
-			"mrc p15, 0, %0, c1, c0, 0\n"
-			"bic %0, %0, #0x00001000\n"
-			"bic %0, %0, #0x00000004\n"
-			"mcr p15, 0, %0, c1, c0, 0\n"
-			/* invalidate I cache */
-			"mov %0, #0\n"
-			"mcr p15, 0, %0, c7, c5, 0\n"
-			/* clear and invalidate D cache */
-			"mov %0, #0\n"
-			"mcr p15, 0, %0, c7, c14, 0\n"
-			/* WFI */
-			"mov %0, #0\n"
-			"mcr p15, 0, %0, c7, c0, 4\n"
-			"nop\n" "nop\n" "nop\n" "nop\n"
-			"nop\n" "nop\n" "nop\n"
-			/* enable I and D cache */
-			"mrc p15, 0, %0, c1, c0, 0\n"
-			"orr %0, %0, #0x00001000\n"
-			"orr %0, %0, #0x00000004\n"
-			"mcr p15, 0, %0, c1, c0, 0\n"
-			: "=r" (reg));
-	local_irq_enable();
+	__asm__ __volatile__(
+		/* disable I and D cache */
+		"mrc p15, 0, %0, c1, c0, 0\n"
+		"bic %0, %0, #0x00001000\n"
+		"bic %0, %0, #0x00000004\n"
+		"mcr p15, 0, %0, c1, c0, 0\n"
+		/* invalidate I cache */
+		"mov %0, #0\n"
+		"mcr p15, 0, %0, c7, c5, 0\n"
+		/* clear and invalidate D cache */
+		"mov %0, #0\n"
+		"mcr p15, 0, %0, c7, c14, 0\n"
+		/* WFI */
+		"mov %0, #0\n"
+		"mcr p15, 0, %0, c7, c0, 4\n"
+		"nop\n" "nop\n" "nop\n" "nop\n"
+		"nop\n" "nop\n" "nop\n"
+		/* enable I and D cache */
+		"mrc p15, 0, %0, c1, c0, 0\n"
+		"orr %0, %0, #0x00001000\n"
+		"orr %0, %0, #0x00000004\n"
+		"mcr p15, 0, %0, c1, c0, 0\n"
+		: "=r" (reg));
 }
 
 static void __iomem *imx3_ioremap(unsigned long phys_addr, size_t size,
@@ -134,8 +132,8 @@
 {
 	mxc_set_cpu_type(MXC_CPU_MX31);
 	mxc_arch_reset_init(MX31_IO_ADDRESS(MX31_WDOG_BASE_ADDR));
-	pm_idle = imx3_idle;
 	imx_ioremap = imx3_ioremap;
+	arm_pm_idle = imx3_idle;
 }
 
 void __init mx31_init_irq(void)
@@ -197,7 +195,7 @@
 	mxc_set_cpu_type(MXC_CPU_MX35);
 	mxc_iomux_v3_init(MX35_IO_ADDRESS(MX35_IOMUXC_BASE_ADDR));
 	mxc_arch_reset_init(MX35_IO_ADDRESS(MX35_WDOG_BASE_ADDR));
-	pm_idle = imx3_idle;
+	arm_pm_idle = imx3_idle;
 	imx_ioremap = imx3_ioremap;
 }
 
diff --git a/arch/arm/mach-imx/mm-imx5.c b/arch/arm/mach-imx/mm-imx5.c
index bc17dfe..49549a7 100644
--- a/arch/arm/mach-imx/mm-imx5.c
+++ b/arch/arm/mach-imx/mm-imx5.c
@@ -26,23 +26,17 @@
 
 static void imx5_idle(void)
 {
-	if (!need_resched()) {
-		/* gpc clock is needed for SRPG */
-		if (gpc_dvfs_clk == NULL) {
-			gpc_dvfs_clk = clk_get(NULL, "gpc_dvfs");
-			if (IS_ERR(gpc_dvfs_clk))
-				goto err0;
-		}
-		clk_enable(gpc_dvfs_clk);
-		mx5_cpu_lp_set(WAIT_UNCLOCKED_POWER_OFF);
-		if (tzic_enable_wake())
-			goto err1;
-		cpu_do_idle();
-err1:
-		clk_disable(gpc_dvfs_clk);
+	/* gpc clock is needed for SRPG */
+	if (gpc_dvfs_clk == NULL) {
+		gpc_dvfs_clk = clk_get(NULL, "gpc_dvfs");
+		if (IS_ERR(gpc_dvfs_clk))
+			return;
 	}
-err0:
-	local_irq_enable();
+	clk_enable(gpc_dvfs_clk);
+	mx5_cpu_lp_set(WAIT_UNCLOCKED_POWER_OFF);
+	if (tzic_enable_wake() != 0)
+		cpu_do_idle();
+	clk_disable(gpc_dvfs_clk);
 }
 
 /*
@@ -108,7 +102,7 @@
 	mxc_set_cpu_type(MXC_CPU_MX51);
 	mxc_iomux_v3_init(MX51_IO_ADDRESS(MX51_IOMUXC_BASE_ADDR));
 	mxc_arch_reset_init(MX51_IO_ADDRESS(MX51_WDOG1_BASE_ADDR));
-	pm_idle = imx5_idle;
+	arm_pm_idle = imx5_idle;
 }
 
 void __init imx53_init_early(void)
diff --git a/arch/arm/mach-imx/pm-imx27.c b/arch/arm/mach-imx/pm-imx27.c
index e455d2f..6fcffa7 100644
--- a/arch/arm/mach-imx/pm-imx27.c
+++ b/arch/arm/mach-imx/pm-imx27.c
@@ -10,7 +10,6 @@
 #include <linux/kernel.h>
 #include <linux/suspend.h>
 #include <linux/io.h>
-#include <mach/system.h>
 #include <mach/hardware.h>
 
 static int mx27_suspend_enter(suspend_state_t state)
@@ -23,7 +22,7 @@
 		cscr &= 0xFFFFFFFC;
 		__raw_writel(cscr, MX27_IO_ADDRESS(MX27_CCM_BASE_ADDR));
 		/* Executes WFI */
-		arch_idle();
+		cpu_do_idle();
 		break;
 
 	default:
diff --git a/arch/arm/mach-integrator/core.c b/arch/arm/mach-integrator/core.c
index 019f0ab..15b87f2 100644
--- a/arch/arm/mach-integrator/core.c
+++ b/arch/arm/mach-integrator/core.c
@@ -35,67 +35,23 @@
 
 static struct amba_pl010_data integrator_uart_data;
 
-static struct amba_device rtc_device = {
-	.dev		= {
-		.init_name = "mb:15",
-	},
-	.res		= {
-		.start	= INTEGRATOR_RTC_BASE,
-		.end	= INTEGRATOR_RTC_BASE + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	.irq		= { IRQ_RTCINT, NO_IRQ },
-};
+#define INTEGRATOR_RTC_IRQ	{ IRQ_RTCINT }
+#define INTEGRATOR_UART0_IRQ	{ IRQ_UARTINT0 }
+#define INTEGRATOR_UART1_IRQ	{ IRQ_UARTINT1 }
+#define KMI0_IRQ		{ IRQ_KMIINT0 }
+#define KMI1_IRQ		{ IRQ_KMIINT1 }
 
-static struct amba_device uart0_device = {
-	.dev		= {
-		.init_name = "mb:16",
-		.platform_data = &integrator_uart_data,
-	},
-	.res		= {
-		.start	= INTEGRATOR_UART0_BASE,
-		.end	= INTEGRATOR_UART0_BASE + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	.irq		= { IRQ_UARTINT0, NO_IRQ },
-};
+static AMBA_APB_DEVICE(rtc, "mb:15", 0,
+	INTEGRATOR_RTC_BASE, INTEGRATOR_RTC_IRQ, NULL);
 
-static struct amba_device uart1_device = {
-	.dev		= {
-		.init_name = "mb:17",
-		.platform_data = &integrator_uart_data,
-	},
-	.res		= {
-		.start	= INTEGRATOR_UART1_BASE,
-		.end	= INTEGRATOR_UART1_BASE + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	.irq		= { IRQ_UARTINT1, NO_IRQ },
-};
+static AMBA_APB_DEVICE(uart0, "mb:16", 0,
+	INTEGRATOR_UART0_BASE, INTEGRATOR_UART0_IRQ, &integrator_uart_data);
 
-static struct amba_device kmi0_device = {
-	.dev		= {
-		.init_name = "mb:18",
-	},
-	.res		= {
-		.start	= KMI0_BASE,
-		.end	= KMI0_BASE + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	.irq		= { IRQ_KMIINT0, NO_IRQ },
-};
+static AMBA_APB_DEVICE(uart1, "mb:17", 0,
+	INTEGRATOR_UART1_BASE, INTEGRATOR_UART1_IRQ, &integrator_uart_data);
 
-static struct amba_device kmi1_device = {
-	.dev		= {
-		.init_name = "mb:19",
-	},
-	.res		= {
-		.start	= KMI1_BASE,
-		.end	= KMI1_BASE + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	.irq		= { IRQ_KMIINT1, NO_IRQ },
-};
+static AMBA_APB_DEVICE(kmi0, "mb:18", 0, KMI0_BASE, KMI0_IRQ, NULL);
+static AMBA_APB_DEVICE(kmi1, "mb:19", 0, KMI1_BASE, KMI1_IRQ, NULL);
 
 static struct amba_device *amba_devs[] __initdata = {
 	&rtc_device,
diff --git a/arch/arm/mach-integrator/impd1.c b/arch/arm/mach-integrator/impd1.c
index 8cbb75a..3e538da 100644
--- a/arch/arm/mach-integrator/impd1.c
+++ b/arch/arm/mach-integrator/impd1.c
@@ -401,24 +401,21 @@
 
 		pc_base = dev->resource.start + idev->offset;
 
-		d = kzalloc(sizeof(struct amba_device), GFP_KERNEL);
+		d = amba_device_alloc(NULL, pc_base, SZ_4K);
 		if (!d)
 			continue;
 
 		dev_set_name(&d->dev, "lm%x:%5.5lx", dev->id, idev->offset >> 12);
 		d->dev.parent	= &dev->dev;
-		d->res.start	= dev->resource.start + idev->offset;
-		d->res.end	= d->res.start + SZ_4K - 1;
-		d->res.flags	= IORESOURCE_MEM;
 		d->irq[0]	= dev->irq;
 		d->irq[1]	= dev->irq;
 		d->periphid	= idev->id;
 		d->dev.platform_data = idev->platform_data;
 
-		ret = amba_device_register(d, &dev->resource);
+		ret = amba_device_add(d, &dev->resource);
 		if (ret) {
 			dev_err(&d->dev, "unable to register device: %d\n", ret);
-			kfree(d);
+			amba_device_put(d);
 		}
 	}
 
diff --git a/arch/arm/mach-integrator/include/mach/system.h b/arch/arm/mach-integrator/include/mach/system.h
deleted file mode 100644
index 901514e..0000000
--- a/arch/arm/mach-integrator/include/mach/system.h
+++ /dev/null
@@ -1,33 +0,0 @@
-/*
- *  arch/arm/mach-integrator/include/mach/system.h
- *
- *  Copyright (C) 1999 ARM Limited
- *  Copyright (C) 2000 Deep Blue Solutions Ltd
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-	/*
-	 * This should do all the clock switching
-	 * and wait for interrupt tricks
-	 */
-	cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-integrator/integrator_cp.c b/arch/arm/mach-integrator/integrator_cp.c
index a8b6aa6..be9ead4 100644
--- a/arch/arm/mach-integrator/integrator_cp.c
+++ b/arch/arm/mach-integrator/integrator_cp.c
@@ -347,32 +347,14 @@
 	.gpio_cd	= -1,
 };
 
-static struct amba_device mmc_device = {
-	.dev		= {
-		.init_name = "mb:1c",
-		.platform_data = &mmc_data,
-	},
-	.res		= {
-		.start	= INTEGRATOR_CP_MMC_BASE,
-		.end	= INTEGRATOR_CP_MMC_BASE + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	.irq		= { IRQ_CP_MMCIINT0, IRQ_CP_MMCIINT1 },
-	.periphid	= 0,
-};
+#define INTEGRATOR_CP_MMC_IRQS	{ IRQ_CP_MMCIINT0, IRQ_CP_MMCIINT1 }
+#define INTEGRATOR_CP_AACI_IRQS	{ IRQ_CP_AACIINT }
 
-static struct amba_device aaci_device = {
-	.dev		= {
-		.init_name = "mb:1d",
-	},
-	.res		= {
-		.start	= INTEGRATOR_CP_AACI_BASE,
-		.end	= INTEGRATOR_CP_AACI_BASE + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	.irq		= { IRQ_CP_AACIINT, NO_IRQ },
-	.periphid	= 0,
-};
+static AMBA_APB_DEVICE(mmc, "mb:1c", 0, INTEGRATOR_CP_MMC_BASE,
+	INTEGRATOR_CP_MMC_IRQS, &mmc_data);
+
+static AMBA_APB_DEVICE(aaci, "mb:1d", 0, INTEGRATOR_CP_AACI_BASE,
+	INTEGRATOR_CP_AACI_IRQS, NULL);
 
 
 /*
@@ -425,21 +407,8 @@
 	.remove		= versatile_clcd_remove_dma,
 };
 
-static struct amba_device clcd_device = {
-	.dev		= {
-		.init_name = "mb:c0",
-		.coherent_dma_mask = ~0,
-		.platform_data = &clcd_data,
-	},
-	.res		= {
-		.start	= INTCP_PA_CLCD_BASE,
-		.end	= INTCP_PA_CLCD_BASE + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	.dma_mask	= ~0,
-	.irq		= { IRQ_CP_CLCDCINT, NO_IRQ },
-	.periphid	= 0,
-};
+static AMBA_AHB_DEVICE(clcd, "mb:c0", 0, INTCP_PA_CLCD_BASE,
+	{ IRQ_CP_CLCDCINT }, &clcd_data);
 
 static struct amba_device *amba_devs[] __initdata = {
 	&mmc_device,
diff --git a/arch/arm/mach-iop13xx/include/mach/system.h b/arch/arm/mach-iop13xx/include/mach/system.h
deleted file mode 100644
index 1f31ed3..0000000
--- a/arch/arm/mach-iop13xx/include/mach/system.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- * arch/arm/mach-iop13xx/include/mach/system.h
- *
- *  Copyright (C) 2004 Intel Corp.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
diff --git a/arch/arm/mach-iop32x/include/mach/system.h b/arch/arm/mach-iop32x/include/mach/system.h
deleted file mode 100644
index 4a88727..0000000
--- a/arch/arm/mach-iop32x/include/mach/system.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- * arch/arm/mach-iop32x/include/mach/system.h
- *
- * Copyright (C) 2001 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
diff --git a/arch/arm/mach-iop33x/include/mach/system.h b/arch/arm/mach-iop33x/include/mach/system.h
deleted file mode 100644
index 4f98e76..0000000
--- a/arch/arm/mach-iop33x/include/mach/system.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- * arch/arm/mach-iop33x/include/mach/system.h
- *
- * Copyright (C) 2001 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
diff --git a/arch/arm/mach-ixp2000/include/mach/system.h b/arch/arm/mach-ixp2000/include/mach/system.h
deleted file mode 100644
index a7fb08b..0000000
--- a/arch/arm/mach-ixp2000/include/mach/system.h
+++ /dev/null
@@ -1,14 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/include/mach/system.h
- *
- * Copyright (C) 2002 Intel Corp.
- * Copyricht (C) 2003-2005 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
diff --git a/arch/arm/mach-ixp23xx/core.c b/arch/arm/mach-ixp23xx/core.c
index 0923bb9..7c1495e 100644
--- a/arch/arm/mach-ixp23xx/core.c
+++ b/arch/arm/mach-ixp23xx/core.c
@@ -441,6 +441,9 @@
 
 void __init ixp23xx_sys_init(void)
 {
+	/* by default, the idle code is disabled */
+	disable_hlt();
+
 	*IXP23XX_EXP_UNIT_FUSE |= 0xf;
 	platform_add_devices(ixp23xx_devices, ARRAY_SIZE(ixp23xx_devices));
 }
diff --git a/arch/arm/mach-ixp23xx/include/mach/system.h b/arch/arm/mach-ixp23xx/include/mach/system.h
deleted file mode 100644
index 277dda7..0000000
--- a/arch/arm/mach-ixp23xx/include/mach/system.h
+++ /dev/null
@@ -1,16 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/include/mach/system.h
- *
- * Copyright (C) 2003 Intel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-static inline void arch_idle(void)
-{
-#if 0
-	if (!hlt_counter)
-		cpu_do_idle();
-#endif
-}
diff --git a/arch/arm/mach-ixp4xx/common.c b/arch/arm/mach-ixp4xx/common.c
index 3841ab4..a6329a0 100644
--- a/arch/arm/mach-ixp4xx/common.c
+++ b/arch/arm/mach-ixp4xx/common.c
@@ -236,6 +236,12 @@
 {
 	int i = 0;
 
+	/*
+	 * ixp4xx does not implement the XScale PWRMODE register
+	 * so it must not call cpu_do_idle().
+	 */
+	disable_hlt();
+
 	/* Route all sources to IRQ instead of FIQ */
 	*IXP4XX_ICLR = 0x0;
 
diff --git a/arch/arm/mach-ixp4xx/include/mach/system.h b/arch/arm/mach-ixp4xx/include/mach/system.h
deleted file mode 100644
index 140a9be..0000000
--- a/arch/arm/mach-ixp4xx/include/mach/system.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- * arch/arm/mach-ixp4xx/include/mach/system.h
- *
- * Copyright (C) 2002 Intel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-static inline void arch_idle(void)
-{
-	/* ixp4xx does not implement the XScale PWRMODE register,
-	 * so it must not call cpu_do_idle() here.
-	 */
-#if 0
-	cpu_do_idle();
-#endif
-}
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index 7fc603b..90ceab7 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -44,6 +44,20 @@
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell GuruPlug Reference Board.
 
+config ARCH_KIRKWOOD_DT
+	bool "Marvell Kirkwood Flattened Device Tree"
+	select USE_OF
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  Marvell Kirkwood using flattened device tree.
+
+config MACH_DREAMPLUG_DT
+	bool "Marvell DreamPlug (Flattened Device Tree)"
+	select ARCH_KIRKWOOD_DT
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  Marvell DreamPlug (Flattened Device Tree).
+
 config MACH_TS219
 	bool "QNAP TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and TS-219P+ Turbo NAS"
 	help
diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile
index 5dcaa81..acbc5e1 100644
--- a/arch/arm/mach-kirkwood/Makefile
+++ b/arch/arm/mach-kirkwood/Makefile
@@ -20,3 +20,4 @@
 obj-$(CONFIG_MACH_T5325)		+= t5325-setup.o
 
 obj-$(CONFIG_CPU_IDLE)			+= cpuidle.o
+obj-$(CONFIG_ARCH_KIRKWOOD_DT)		+= board-dt.o
diff --git a/arch/arm/mach-kirkwood/Makefile.boot b/arch/arm/mach-kirkwood/Makefile.boot
index 760a0ef..16f9385 100644
--- a/arch/arm/mach-kirkwood/Makefile.boot
+++ b/arch/arm/mach-kirkwood/Makefile.boot
@@ -1,3 +1,5 @@
    zreladdr-y	+= 0x00008000
 params_phys-y	:= 0x00000100
 initrd_phys-y	:= 0x00800000
+
+dtb-$(CONFIG_MACH_DREAMPLUG_DT) += kirkwood-dreamplug.dtb
diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c
new file mode 100644
index 0000000..fbe6405
--- /dev/null
+++ b/arch/arm/mach-kirkwood/board-dt.c
@@ -0,0 +1,180 @@
+/*
+ * Copyright 2012 (C), Jason Cooper <jason@lakedaemon.net>
+ *
+ * arch/arm/mach-kirkwood/board-dt.c
+ *
+ * Marvell DreamPlug Reference Board Setup
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/partitions.h>
+#include <linux/ata_platform.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_fdt.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <linux/mtd/physmap.h>
+#include <linux/spi/flash.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/orion_spi.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/kirkwood.h>
+#include <plat/mvsdio.h>
+#include "common.h"
+#include "mpp.h"
+
+static struct of_device_id kirkwood_dt_match_table[] __initdata = {
+	{ .compatible = "simple-bus", },
+	{ }
+};
+
+struct mtd_partition dreamplug_partitions[] = {
+	{
+		.name	= "u-boot",
+		.size	= SZ_512K,
+		.offset = 0,
+	},
+	{
+		.name	= "u-boot env",
+		.size	= SZ_64K,
+		.offset = SZ_512K + SZ_512K,
+	},
+	{
+		.name	= "dtb",
+		.size	= SZ_64K,
+		.offset = SZ_512K + SZ_512K + SZ_512K,
+	},
+};
+
+static const struct flash_platform_data dreamplug_spi_slave_data = {
+	.type		= "mx25l1606e",
+	.name		= "spi_flash",
+	.parts		= dreamplug_partitions,
+	.nr_parts	= ARRAY_SIZE(dreamplug_partitions),
+};
+
+static struct spi_board_info __initdata dreamplug_spi_slave_info[] = {
+	{
+		.modalias	= "m25p80",
+		.platform_data	= &dreamplug_spi_slave_data,
+		.irq		= -1,
+		.max_speed_hz	= 50000000,
+		.bus_num	= 0,
+		.chip_select	= 0,
+	},
+};
+
+static struct mv643xx_eth_platform_data dreamplug_ge00_data = {
+	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
+};
+
+static struct mv643xx_eth_platform_data dreamplug_ge01_data = {
+	.phy_addr	= MV643XX_ETH_PHY_ADDR(1),
+};
+
+static struct mv_sata_platform_data dreamplug_sata_data = {
+	.n_ports	= 1,
+};
+
+static struct mvsdio_platform_data dreamplug_mvsdio_data = {
+	/* unfortunately the CD signal has not been connected */
+};
+
+static struct gpio_led dreamplug_led_pins[] = {
+	{
+		.name			= "dreamplug:blue:bluetooth",
+		.gpio			= 47,
+		.active_low		= 1,
+	},
+	{
+		.name			= "dreamplug:green:wifi",
+		.gpio			= 48,
+		.active_low		= 1,
+	},
+	{
+		.name			= "dreamplug:green:wifi_ap",
+		.gpio			= 49,
+		.active_low		= 1,
+	},
+};
+
+static struct gpio_led_platform_data dreamplug_led_data = {
+	.leds		= dreamplug_led_pins,
+	.num_leds	= ARRAY_SIZE(dreamplug_led_pins),
+};
+
+static struct platform_device dreamplug_leds = {
+	.name	= "leds-gpio",
+	.id	= -1,
+	.dev	= {
+		.platform_data	= &dreamplug_led_data,
+	}
+};
+
+static unsigned int dreamplug_mpp_config[] __initdata = {
+	MPP0_SPI_SCn,
+	MPP1_SPI_MOSI,
+	MPP2_SPI_SCK,
+	MPP3_SPI_MISO,
+	MPP47_GPIO,	/* Bluetooth LED */
+	MPP48_GPIO,	/* Wifi LED */
+	MPP49_GPIO,	/* Wifi AP LED */
+	0
+};
+
+static void __init dreamplug_init(void)
+{
+	/*
+	 * Basic setup. Needs to be called early.
+	 */
+	kirkwood_mpp_conf(dreamplug_mpp_config);
+
+	spi_register_board_info(dreamplug_spi_slave_info,
+				ARRAY_SIZE(dreamplug_spi_slave_info));
+	kirkwood_spi_init();
+
+	kirkwood_ehci_init();
+	kirkwood_ge00_init(&dreamplug_ge00_data);
+	kirkwood_ge01_init(&dreamplug_ge01_data);
+	kirkwood_sata_init(&dreamplug_sata_data);
+	kirkwood_sdio_init(&dreamplug_mvsdio_data);
+
+	platform_device_register(&dreamplug_leds);
+}
+
+static void __init kirkwood_dt_init(void)
+{
+	kirkwood_init();
+
+	if (of_machine_is_compatible("globalscale,dreamplug"))
+		dreamplug_init();
+
+	of_platform_populate(NULL, kirkwood_dt_match_table, NULL, NULL);
+}
+
+static const char *kirkwood_dt_board_compat[] = {
+	"globalscale,dreamplug",
+	NULL
+};
+
+DT_MACHINE_START(KIRKWOOD_DT, "Marvell Kirkwood (Flattened Device Tree)")
+	/* Maintainer: Jason Cooper <jason@lakedaemon.net> */
+	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
+	.init_irq	= kirkwood_init_irq,
+	.timer		= &kirkwood_timer,
+	.init_machine	= kirkwood_dt_init,
+	.restart	= kirkwood_restart,
+	.dt_compat	= kirkwood_dt_board_compat,
+MACHINE_END
diff --git a/arch/arm/mach-kirkwood/include/mach/system.h b/arch/arm/mach-kirkwood/include/mach/system.h
deleted file mode 100644
index 5fddde0..0000000
--- a/arch/arm/mach-kirkwood/include/mach/system.h
+++ /dev/null
@@ -1,17 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/include/mach/system.h
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-ks8695/include/mach/system.h b/arch/arm/mach-ks8695/include/mach/system.h
deleted file mode 100644
index 59fe992..0000000
--- a/arch/arm/mach-ks8695/include/mach/system.h
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * arch/arm/mach-s3c2410/include/mach/system.h
- *
- * Copyright (C) 2006 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * KS8695 - System function defines and includes
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static void arch_idle(void)
-{
-	/*
-	 * This should do all the clock switching
-	 * and wait for interrupt tricks,
-	 */
-	cpu_do_idle();
-
-}
-
-#endif
diff --git a/arch/arm/mach-lpc32xx/include/mach/system.h b/arch/arm/mach-lpc32xx/include/mach/system.h
deleted file mode 100644
index bf176c9..0000000
--- a/arch/arm/mach-lpc32xx/include/mach/system.h
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * arch/arm/mach-lpc32xx/include/mach/system.h
- *
- * Author: Kevin Wells <kevin.wells@nxp.com>
- *
- * Copyright (C) 2010 NXP Semiconductors
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static void arch_idle(void)
-{
-	cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c
index bfee5b4..5d51c10 100644
--- a/arch/arm/mach-lpc32xx/phy3250.c
+++ b/arch/arm/mach-lpc32xx/phy3250.c
@@ -149,20 +149,8 @@
 	.remove		= lpc32xx_clcd_remove,
 };
 
-static struct amba_device lpc32xx_clcd_device = {
-	.dev				= {
-		.coherent_dma_mask	= ~0,
-		.init_name		= "dev:clcd",
-		.platform_data		= &lpc32xx_clcd_data,
-	},
-	.res				= {
-		.start			= LPC32XX_LCD_BASE,
-		.end			= (LPC32XX_LCD_BASE + SZ_4K - 1),
-		.flags			= IORESOURCE_MEM,
-	},
-	.dma_mask			= ~0,
-	.irq				= {IRQ_LPC32XX_LCD, NO_IRQ},
-};
+static AMBA_AHB_DEVICE(lpc32xx_clcd, "dev:clcd", 0,
+	LPC32XX_LCD_BASE, { IRQ_LPC32XX_LCD }, &lpc32xx_clcd_data);
 
 /*
  * AMBA SSP (SPI)
@@ -191,20 +179,8 @@
 	.enable_dma		= 0,
 };
 
-static struct amba_device lpc32xx_ssp0_device = {
-	.dev				= {
-		.coherent_dma_mask	= ~0,
-		.init_name		= "dev:ssp0",
-		.platform_data		= &lpc32xx_ssp0_data,
-	},
-	.res				= {
-		.start			= LPC32XX_SSP0_BASE,
-		.end			= (LPC32XX_SSP0_BASE + SZ_4K - 1),
-		.flags			= IORESOURCE_MEM,
-	},
-	.dma_mask			= ~0,
-	.irq				= {IRQ_LPC32XX_SSP0, NO_IRQ},
-};
+static AMBA_APB_DEVICE(lpc32xx_ssp0, "dev:ssp0", 0,
+	LPC32XX_SSP0_BASE, { IRQ_LPC32XX_SSP0 }, &lpc32xx_ssp0_data);
 
 /* AT25 driver registration */
 static int __init phy3250_spi_board_register(void)
diff --git a/arch/arm/mach-mmp/include/mach/system.h b/arch/arm/mach-mmp/include/mach/system.h
deleted file mode 100644
index 1d001ea..0000000
--- a/arch/arm/mach-mmp/include/mach/system.h
+++ /dev/null
@@ -1,16 +0,0 @@
-/*
- * linux/arch/arm/mach-mmp/include/mach/system.h
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_MACH_SYSTEM_H
-#define __ASM_MACH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
-#endif /* __ASM_MACH_SYSTEM_H */
diff --git a/arch/arm/mach-mmp/mmp2.c b/arch/arm/mach-mmp/mmp2.c
index 617c60a..c709a24 100644
--- a/arch/arm/mach-mmp/mmp2.c
+++ b/arch/arm/mach-mmp/mmp2.c
@@ -223,6 +223,7 @@
 	}, {
 		.start	= IRQ_MMP2_GPIO,
 		.end	= IRQ_MMP2_GPIO,
+		.name	= "gpio_mux",
 		.flags	= IORESOURCE_IRQ,
 	},
 };
diff --git a/arch/arm/mach-mmp/pxa168.c b/arch/arm/mach-mmp/pxa168.c
index ada1213..f10f87d 100644
--- a/arch/arm/mach-mmp/pxa168.c
+++ b/arch/arm/mach-mmp/pxa168.c
@@ -166,6 +166,7 @@
 	}, {
 		.start	= IRQ_PXA168_GPIOX,
 		.end	= IRQ_PXA168_GPIOX,
+		.name	= "gpio_mux",
 		.flags	= IORESOURCE_IRQ,
 	},
 };
diff --git a/arch/arm/mach-mmp/pxa910.c b/arch/arm/mach-mmp/pxa910.c
index 3241a25..0c87e69 100644
--- a/arch/arm/mach-mmp/pxa910.c
+++ b/arch/arm/mach-mmp/pxa910.c
@@ -173,6 +173,7 @@
 	}, {
 		.start	= IRQ_PXA910_AP_GPIO,
 		.end	= IRQ_PXA910_AP_GPIO,
+		.name	= "gpio_mux",
 		.flags	= IORESOURCE_IRQ,
 	},
 };
diff --git a/arch/arm/mach-msm/idle.S b/arch/arm/mach-msm/idle.S
deleted file mode 100644
index 6a94f05..0000000
--- a/arch/arm/mach-msm/idle.S
+++ /dev/null
@@ -1,36 +0,0 @@
-/* arch/arm/mach-msm/include/mach/idle.S
- *
- * Idle processing for MSM7K - work around bugs with SWFI.
- *
- * Copyright (c) 2007 QUALCOMM Incorporated.
- * Copyright (C) 2007 Google, Inc. 
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */ 
-		
-#include <linux/linkage.h>
-#include <asm/assembler.h>
-
-ENTRY(arch_idle)
-#ifdef CONFIG_MSM7X00A_IDLE
-	mrc     p15, 0, r1, c1, c0, 0    /* read current CR    */
-	bic     r0, r1, #(1 << 2)        /* clear dcache bit   */
-	bic     r0, r0, #(1 << 12)       /* clear icache bit   */
-	mcr     p15, 0, r0, c1, c0, 0    /* disable d/i cache  */
-
-	mov     r0, #0                   /* prepare wfi value  */
-	mcr     p15, 0, r0, c7, c10, 0   /* flush the cache    */
-	mcr     p15, 0, r0, c7, c10, 4   /* memory barrier     */
-	mcr     p15, 0, r0, c7, c0, 4    /* wait for interrupt */
-
-	mcr     p15, 0, r1, c1, c0, 0    /* restore d/i cache  */
-#endif
-	mov     pc, lr
diff --git a/arch/arm/mach-msm/idle.c b/arch/arm/mach-msm/idle.c
new file mode 100644
index 0000000..0c9e13c
--- /dev/null
+++ b/arch/arm/mach-msm/idle.c
@@ -0,0 +1,49 @@
+/* arch/arm/mach-msm/idle.c
+ *
+ * Idle processing for MSM7K - work around bugs with SWFI.
+ *
+ * Copyright (c) 2007 QUALCOMM Incorporated.
+ * Copyright (C) 2007 Google, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/init.h>
+#include <asm/system.h>
+
+static void msm_idle(void)
+{
+#ifdef CONFIG_MSM7X00A_IDLE
+	asm volatile (
+
+	"mrc     p15, 0, r1, c1, c0, 0    /* read current CR    */ \n\t"
+	"bic     r0, r1, #(1 << 2)        /* clear dcache bit   */ \n\t"
+	"bic     r0, r0, #(1 << 12)       /* clear icache bit   */ \n\t"
+	"mcr     p15, 0, r0, c1, c0, 0    /* disable d/i cache  */ \n\t"
+
+	"mov     r0, #0                   /* prepare wfi value  */ \n\t"
+	"mcr     p15, 0, r0, c7, c10, 0   /* flush the cache    */ \n\t"
+	"mcr     p15, 0, r0, c7, c10, 4   /* memory barrier     */ \n\t"
+	"mcr     p15, 0, r0, c7, c0, 4    /* wait for interrupt */ \n\t"
+
+	"mcr     p15, 0, r1, c1, c0, 0    /* restore d/i cache  */ \n\t"
+
+	: : : "r0","r1" );
+#endif
+}
+
+static int __init msm_idle_init(void)
+{
+	arm_pm_idle = msm_idle;
+	return 0;
+}
+
+arch_initcall(msm_idle_init);
diff --git a/arch/arm/mach-msm/include/mach/system.h b/arch/arm/mach-msm/include/mach/system.h
index 311db2b..f5fb2ec 100644
--- a/arch/arm/mach-msm/include/mach/system.h
+++ b/arch/arm/mach-msm/include/mach/system.h
@@ -12,7 +12,6 @@
  * GNU General Public License for more details.
  *
  */
-void arch_idle(void);
 
 /* low level hardware reset hook -- for example, hitting the
  * PSHOLD line on the PMIC to hard reset the system
diff --git a/arch/arm/mach-mv78xx0/include/mach/system.h b/arch/arm/mach-mv78xx0/include/mach/system.h
deleted file mode 100644
index 8c3a538..0000000
--- a/arch/arm/mach-mv78xx0/include/mach/system.h
+++ /dev/null
@@ -1,17 +0,0 @@
-/*
- * arch/arm/mach-mv78xx0/include/mach/system.h
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-mxs/Kconfig b/arch/arm/mach-mxs/Kconfig
index cf00b3e..c57f996 100644
--- a/arch/arm/mach-mxs/Kconfig
+++ b/arch/arm/mach-mxs/Kconfig
@@ -83,6 +83,18 @@
 	select MXS_HAVE_PLATFORM_MXSFB
 	select MXS_OCOTP
 
+config MODULE_APX4
+	bool
+	select SOC_IMX28
+	select LEDS_GPIO_REGISTER
+	select MXS_HAVE_AMBA_DUART
+	select MXS_HAVE_PLATFORM_AUART
+	select MXS_HAVE_PLATFORM_FEC
+	select MXS_HAVE_PLATFORM_MXS_I2C
+	select MXS_HAVE_PLATFORM_MXS_MMC
+	select MXS_HAVE_PLATFORM_MXS_SAIF
+	select MXS_OCOTP
+
 config MACH_TX28
 	bool "Ka-Ro TX28 module"
 	select MODULE_TX28
@@ -91,4 +103,8 @@
 	bool "Support DENX M28EVK Platform"
 	select MODULE_M28
 
+config MACH_APX4DEVKIT
+	bool "Support Bluegiga APX4 Development Kit"
+	select MODULE_APX4
+
 endif
diff --git a/arch/arm/mach-mxs/Makefile b/arch/arm/mach-mxs/Makefile
index 8c93b24..908bf9a 100644
--- a/arch/arm/mach-mxs/Makefile
+++ b/arch/arm/mach-mxs/Makefile
@@ -11,6 +11,7 @@
 obj-$(CONFIG_MACH_MX23EVK) += mach-mx23evk.o
 obj-$(CONFIG_MACH_MX28EVK) += mach-mx28evk.o
 obj-$(CONFIG_MACH_M28EVK)    += mach-m28evk.o
+obj-$(CONFIG_MACH_APX4DEVKIT) += mach-apx4devkit.o
 obj-$(CONFIG_MODULE_TX28) += module-tx28.o
 obj-$(CONFIG_MACH_TX28)    += mach-tx28.o
 
diff --git a/arch/arm/mach-mxs/devices.c b/arch/arm/mach-mxs/devices.c
index fe3e847..01faffe 100644
--- a/arch/arm/mach-mxs/devices.c
+++ b/arch/arm/mach-mxs/devices.c
@@ -77,16 +77,18 @@
 
 int __init mxs_add_amba_device(const struct amba_device *dev)
 {
-	struct amba_device *adev = kmalloc(sizeof(*adev), GFP_KERNEL);
+	struct amba_device *adev = amba_device_alloc(dev->dev.init_name,
+		dev->res.start, resource_size(&dev->res));
 
 	if (!adev) {
 		pr_err("%s: failed to allocate memory", __func__);
 		return -ENOMEM;
 	}
 
-	*adev = *dev;
+	adev->irq[0] = dev->irq[0];
+	adev->irq[1] = dev->irq[1];
 
-	return amba_device_register(adev, &iomem_resource);
+	return amba_device_add(adev, &iomem_resource);
 }
 
 struct device mxs_apbh_bus = {
diff --git a/arch/arm/mach-mxs/devices/amba-duart.c b/arch/arm/mach-mxs/devices/amba-duart.c
index a559db0..a5479f7 100644
--- a/arch/arm/mach-mxs/devices/amba-duart.c
+++ b/arch/arm/mach-mxs/devices/amba-duart.c
@@ -23,7 +23,7 @@
 		.end = (soc ## _DUART_BASE_ADDR) + SZ_8K - 1,	\
 		.flags = IORESOURCE_MEM,			\
 	},							\
-	.irq = {soc ## _INT_DUART, NO_IRQ},			\
+	.irq = {soc ## _INT_DUART},				\
 }
 
 #ifdef CONFIG_SOC_IMX23
diff --git a/arch/arm/mach-mxs/include/mach/digctl.h b/arch/arm/mach-mxs/include/mach/digctl.h
index 49a888c..1796406 100644
--- a/arch/arm/mach-mxs/include/mach/digctl.h
+++ b/arch/arm/mach-mxs/include/mach/digctl.h
@@ -18,4 +18,5 @@
 #define HW_DIGCTL_CTRL			0x0
 #define  BP_DIGCTL_CTRL_SAIF_CLKMUX	10
 #define  BM_DIGCTL_CTRL_SAIF_CLKMUX	(0x3 << 10)
+#define HW_DIGCTL_CHIPID		0x310
 #endif
diff --git a/arch/arm/mach-mxs/include/mach/mxs.h b/arch/arm/mach-mxs/include/mach/mxs.h
index bde5f66..7d4fb6d 100644
--- a/arch/arm/mach-mxs/include/mach/mxs.h
+++ b/arch/arm/mach-mxs/include/mach/mxs.h
@@ -23,22 +23,10 @@
 #include <linux/io.h>
 #endif
 #include <asm/mach-types.h>
+#include <mach/digctl.h>
 #include <mach/hardware.h>
 
 /*
- * MXS CPU types
- */
-#define cpu_is_mx23()		(					\
-		machine_is_mx23evk() ||					\
-		machine_is_stmp378x() ||				\
-		0)
-#define cpu_is_mx28()		(					\
-		machine_is_mx28evk() ||					\
-		machine_is_m28evk() ||					\
-		machine_is_tx28() ||					\
-		0)
-
-/*
  * IO addresses common to MXS-based
  */
 #define MXS_IO_BASE_ADDR		0x80000000
@@ -109,6 +97,21 @@
 {
 	__raw_writel(mask, reg + MXS_TOG_ADDR);
 }
+
+/*
+ * MXS CPU types
+ */
+#define MXS_CHIPID (MXS_IO_ADDRESS(MXS_DIGCTL_BASE_ADDR) + HW_DIGCTL_CHIPID)
+
+static inline int cpu_is_mx23(void)
+{
+	return ((__raw_readl(MXS_CHIPID) >> 16) == 0x3780);
+}
+
+static inline int cpu_is_mx28(void)
+{
+	return ((__raw_readl(MXS_CHIPID) >> 16) == 0x2800);
+}
 #endif
 
 #endif /* __MACH_MXS_H__ */
diff --git a/arch/arm/mach-mxs/include/mach/system.h b/arch/arm/mach-mxs/include/mach/system.h
deleted file mode 100644
index e7ad1bb..0000000
--- a/arch/arm/mach-mxs/include/mach/system.h
+++ /dev/null
@@ -1,25 +0,0 @@
-/*
- *  Copyright (C) 1999 ARM Limited
- *  Copyright (C) 2000 Deep Blue Solutions Ltd
- *  Copyright 2004-2008 Freescale Semiconductor, Inc. All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __MACH_MXS_SYSTEM_H__
-#define __MACH_MXS_SYSTEM_H__
-
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
-
-#endif /* __MACH_MXS_SYSTEM_H__ */
diff --git a/arch/arm/mach-mxs/include/mach/uncompress.h b/arch/arm/mach-mxs/include/mach/uncompress.h
index 6777674..ef28114 100644
--- a/arch/arm/mach-mxs/include/mach/uncompress.h
+++ b/arch/arm/mach-mxs/include/mach/uncompress.h
@@ -18,8 +18,6 @@
 #ifndef __MACH_MXS_UNCOMPRESS_H__
 #define __MACH_MXS_UNCOMPRESS_H__
 
-#include <asm/mach-types.h>
-
 unsigned long mxs_duart_base;
 
 #define MXS_DUART(x)	(*(volatile unsigned long *)(mxs_duart_base + (x)))
@@ -55,16 +53,17 @@
 
 #define MX23_DUART_BASE_ADDR	0x80070000
 #define MX28_DUART_BASE_ADDR	0x80074000
+#define MXS_DIGCTL_CHIPID	0x8001c310
 
 static inline void __arch_decomp_setup(unsigned long arch_id)
 {
-	switch (arch_id) {
-	case MACH_TYPE_MX23EVK:
+	u16 chipid = (*(volatile unsigned long *) MXS_DIGCTL_CHIPID) >> 16;
+
+	switch (chipid) {
+	case 0x3780:
 		mxs_duart_base = MX23_DUART_BASE_ADDR;
 		break;
-	case MACH_TYPE_MX28EVK:
-	case MACH_TYPE_M28EVK:
-	case MACH_TYPE_TX28:
+	case 0x2800:
 		mxs_duart_base = MX28_DUART_BASE_ADDR;
 		break;
 	default:
diff --git a/arch/arm/mach-mxs/mach-apx4devkit.c b/arch/arm/mach-mxs/mach-apx4devkit.c
new file mode 100644
index 0000000..48a7fab
--- /dev/null
+++ b/arch/arm/mach-mxs/mach-apx4devkit.c
@@ -0,0 +1,260 @@
+/*
+ * Copyright (C) 2011-2012
+ * Lauri Hintsala, Bluegiga, <lauri.hintsala@bluegiga.com>
+ * Veli-Pekka Peltola, Bluegiga, <veli-pekka.peltola@bluegiga.com>
+ *
+ * based on: mach-mx28evk.c
+ * Copyright 2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <linux/clk.h>
+#include <linux/i2c.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/fixed.h>
+#include <linux/micrel_phy.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+
+#include <mach/common.h>
+#include <mach/digctl.h>
+#include <mach/iomux-mx28.h>
+
+#include "devices-mx28.h"
+
+#define APX4DEVKIT_GPIO_USERLED	MXS_GPIO_NR(3, 28)
+
+static const iomux_cfg_t apx4devkit_pads[] __initconst = {
+	/* duart */
+	MX28_PAD_PWM0__DUART_RX | MXS_PAD_CTRL,
+	MX28_PAD_PWM1__DUART_TX | MXS_PAD_CTRL,
+
+	/* auart0 */
+	MX28_PAD_AUART0_RX__AUART0_RX | MXS_PAD_CTRL,
+	MX28_PAD_AUART0_TX__AUART0_TX | MXS_PAD_CTRL,
+	MX28_PAD_AUART0_CTS__AUART0_CTS | MXS_PAD_CTRL,
+	MX28_PAD_AUART0_RTS__AUART0_RTS | MXS_PAD_CTRL,
+
+	/* auart1 */
+	MX28_PAD_AUART1_RX__AUART1_RX | MXS_PAD_CTRL,
+	MX28_PAD_AUART1_TX__AUART1_TX | MXS_PAD_CTRL,
+
+	/* auart2 */
+	MX28_PAD_SSP2_SCK__AUART2_RX | MXS_PAD_CTRL,
+	MX28_PAD_SSP2_MOSI__AUART2_TX | MXS_PAD_CTRL,
+
+	/* auart3 */
+	MX28_PAD_SSP2_MISO__AUART3_RX | MXS_PAD_CTRL,
+	MX28_PAD_SSP2_SS0__AUART3_TX | MXS_PAD_CTRL,
+
+#define MXS_PAD_FEC	(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP)
+	/* fec0 */
+	MX28_PAD_ENET0_MDC__ENET0_MDC | MXS_PAD_FEC,
+	MX28_PAD_ENET0_MDIO__ENET0_MDIO | MXS_PAD_FEC,
+	MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | MXS_PAD_FEC,
+	MX28_PAD_ENET0_RXD0__ENET0_RXD0 | MXS_PAD_FEC,
+	MX28_PAD_ENET0_RXD1__ENET0_RXD1 | MXS_PAD_FEC,
+	MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | MXS_PAD_FEC,
+	MX28_PAD_ENET0_TXD0__ENET0_TXD0 | MXS_PAD_FEC,
+	MX28_PAD_ENET0_TXD1__ENET0_TXD1 | MXS_PAD_FEC,
+	MX28_PAD_ENET_CLK__CLKCTRL_ENET | MXS_PAD_FEC,
+
+	/* i2c */
+	MX28_PAD_I2C0_SCL__I2C0_SCL,
+	MX28_PAD_I2C0_SDA__I2C0_SDA,
+
+	/* mmc0 */
+	MX28_PAD_SSP0_DATA0__SSP0_D0 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SSP0_DATA1__SSP0_D1 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SSP0_DATA2__SSP0_D2 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SSP0_DATA3__SSP0_D3 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SSP0_DATA4__SSP0_D4 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SSP0_DATA5__SSP0_D5 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SSP0_DATA6__SSP0_D6 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SSP0_DATA7__SSP0_D7 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SSP0_CMD__SSP0_CMD |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+	MX28_PAD_SSP0_SCK__SSP0_SCK |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+
+	/* led */
+	MX28_PAD_PWM3__GPIO_3_28 | MXS_PAD_CTRL,
+
+	/* saif0 & saif1 */
+	MX28_PAD_SAIF0_MCLK__SAIF0_MCLK |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+};
+
+/* led */
+static const struct gpio_led apx4devkit_leds[] __initconst = {
+	{
+		.name = "user-led",
+		.default_trigger = "heartbeat",
+		.gpio = APX4DEVKIT_GPIO_USERLED,
+	},
+};
+
+static const struct gpio_led_platform_data apx4devkit_led_data __initconst = {
+	.leds = apx4devkit_leds,
+	.num_leds = ARRAY_SIZE(apx4devkit_leds),
+};
+
+static const struct fec_platform_data mx28_fec_pdata __initconst = {
+	.phy = PHY_INTERFACE_MODE_RMII,
+};
+
+static const struct mxs_mmc_platform_data apx4devkit_mmc_pdata __initconst = {
+	.wp_gpio = -EINVAL,
+	.flags = SLOTF_4_BIT_CAPABLE,
+};
+
+static const struct i2c_board_info apx4devkit_i2c_boardinfo[] __initconst = {
+	{ I2C_BOARD_INFO("sgtl5000", 0x0a) }, /* ASoC */
+	{ I2C_BOARD_INFO("pcf8563", 0x51) }, /* RTC */
+};
+
+#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || \
+		defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE)
+static struct regulator_consumer_supply apx4devkit_audio_consumer_supplies[] = {
+	REGULATOR_SUPPLY("VDDA", "0-000a"),
+	REGULATOR_SUPPLY("VDDIO", "0-000a"),
+};
+
+static struct regulator_init_data apx4devkit_vdd_reg_init_data = {
+	.constraints	= {
+		.name	= "3V3",
+		.always_on = 1,
+	},
+	.consumer_supplies = apx4devkit_audio_consumer_supplies,
+	.num_consumer_supplies = ARRAY_SIZE(apx4devkit_audio_consumer_supplies),
+};
+
+static struct fixed_voltage_config apx4devkit_vdd_pdata = {
+	.supply_name	= "board-3V3",
+	.microvolts	= 3300000,
+	.gpio		= -EINVAL,
+	.enabled_at_boot = 1,
+	.init_data	= &apx4devkit_vdd_reg_init_data,
+};
+
+static struct platform_device apx4devkit_voltage_regulator = {
+	.name		= "reg-fixed-voltage",
+	.id		= -1,
+	.num_resources	= 0,
+	.dev		= {
+		.platform_data	= &apx4devkit_vdd_pdata,
+	},
+};
+
+static void __init apx4devkit_add_regulators(void)
+{
+	platform_device_register(&apx4devkit_voltage_regulator);
+}
+#else
+static void __init apx4devkit_add_regulators(void) {}
+#endif
+
+static const struct mxs_saif_platform_data
+			apx4devkit_mxs_saif_pdata[] __initconst = {
+	/* working on EXTMSTR0 mode (saif0 master, saif1 slave) */
+	{
+		.master_mode = 1,
+		.master_id = 0,
+	}, {
+		.master_mode = 0,
+		.master_id = 0,
+	},
+};
+
+static int apx4devkit_phy_fixup(struct phy_device *phy)
+{
+	phy->dev_flags |= MICREL_PHY_50MHZ_CLK;
+	return 0;
+}
+
+static void __init apx4devkit_init(void)
+{
+	mxs_iomux_setup_multiple_pads(apx4devkit_pads,
+			ARRAY_SIZE(apx4devkit_pads));
+
+	mx28_add_duart();
+	mx28_add_auart0();
+	mx28_add_auart1();
+	mx28_add_auart2();
+	mx28_add_auart3();
+
+	/*
+	 * Register fixup for the Micrel KS8031 PHY clock
+	 * (shares same ID with KS8051)
+	 */
+	phy_register_fixup_for_uid(PHY_ID_KS8051, MICREL_PHY_ID_MASK,
+			apx4devkit_phy_fixup);
+
+	mx28_add_fec(0, &mx28_fec_pdata);
+
+	mx28_add_mxs_mmc(0, &apx4devkit_mmc_pdata);
+
+	gpio_led_register_device(0, &apx4devkit_led_data);
+
+	mxs_saif_clkmux_select(MXS_DIGCTL_SAIF_CLKMUX_EXTMSTR0);
+	mx28_add_saif(0, &apx4devkit_mxs_saif_pdata[0]);
+	mx28_add_saif(1, &apx4devkit_mxs_saif_pdata[1]);
+
+	apx4devkit_add_regulators();
+
+	mx28_add_mxs_i2c(0);
+	i2c_register_board_info(0, apx4devkit_i2c_boardinfo,
+			ARRAY_SIZE(apx4devkit_i2c_boardinfo));
+
+	mxs_add_platform_device("mxs-sgtl5000", 0, NULL, 0, NULL, 0);
+}
+
+static void __init apx4devkit_timer_init(void)
+{
+	mx28_clocks_init();
+}
+
+static struct sys_timer apx4devkit_timer = {
+	.init	= apx4devkit_timer_init,
+};
+
+MACHINE_START(APX4DEVKIT, "Bluegiga APX4 Development Kit")
+	.map_io		= mx28_map_io,
+	.init_irq	= mx28_init_irq,
+	.timer		= &apx4devkit_timer,
+	.init_machine	= apx4devkit_init,
+	.restart	= mxs_restart,
+MACHINE_END
diff --git a/arch/arm/mach-mxs/mach-m28evk.c b/arch/arm/mach-mxs/mach-m28evk.c
index 2f27582..06d7996 100644
--- a/arch/arm/mach-mxs/mach-m28evk.c
+++ b/arch/arm/mach-mxs/mach-m28evk.c
@@ -247,18 +247,15 @@
 	u32 val;
 	const u32 *ocotp = mxs_get_ocotp();
 
-	if (!ocotp) {
-		pr_err("%s: timeout when reading fec mac from OCOTP\n",
-			__func__);
+	if (!ocotp)
 		return -ETIMEDOUT;
-	}
 
 	/*
 	 * OCOTP only stores the last 4 octets for each mac address,
 	 * so hard-code DENX OUI (C0:E5:4E) here.
 	 */
 	for (i = 0; i < 2; i++) {
-		val = ocotp[i * 4];
+		val = ocotp[i];
 		mx28_fec_pdata[i].mac[0] = 0xC0;
 		mx28_fec_pdata[i].mac[1] = 0xE5;
 		mx28_fec_pdata[i].mac[2] = 0x4E;
diff --git a/arch/arm/mach-mxs/mach-mx28evk.c b/arch/arm/mach-mxs/mach-mx28evk.c
index fdb0a56..e386c14 100644
--- a/arch/arm/mach-mxs/mach-mx28evk.c
+++ b/arch/arm/mach-mxs/mach-mx28evk.c
@@ -223,7 +223,6 @@
 /* fec */
 static void __init mx28evk_fec_reset(void)
 {
-	int ret;
 	struct clk *clk;
 
 	/* Enable fec phy clock */
@@ -231,32 +230,7 @@
 	if (!IS_ERR(clk))
 		clk_prepare_enable(clk);
 
-	/* Power up fec phy */
-	ret = gpio_request(MX28EVK_FEC_PHY_POWER, "fec-phy-power");
-	if (ret) {
-		pr_err("Failed to request gpio fec-phy-%s: %d\n", "power", ret);
-		return;
-	}
-
-	ret = gpio_direction_output(MX28EVK_FEC_PHY_POWER, 0);
-	if (ret) {
-		pr_err("Failed to drive gpio fec-phy-%s: %d\n", "power", ret);
-		return;
-	}
-
-	/* Reset fec phy */
-	ret = gpio_request(MX28EVK_FEC_PHY_RESET, "fec-phy-reset");
-	if (ret) {
-		pr_err("Failed to request gpio fec-phy-%s: %d\n", "reset", ret);
-		return;
-	}
-
-	gpio_direction_output(MX28EVK_FEC_PHY_RESET, 0);
-	if (ret) {
-		pr_err("Failed to drive gpio fec-phy-%s: %d\n", "reset", ret);
-		return;
-	}
-
+	gpio_set_value(MX28EVK_FEC_PHY_RESET, 0);
 	mdelay(1);
 	gpio_set_value(MX28EVK_FEC_PHY_RESET, 1);
 }
@@ -278,14 +252,14 @@
 	const u32 *ocotp = mxs_get_ocotp();
 
 	if (!ocotp)
-		goto error;
+		return -ETIMEDOUT;
 
 	/*
 	 * OCOTP only stores the last 4 octets for each mac address,
 	 * so hard-code Freescale OUI (00:04:9f) here.
 	 */
 	for (i = 0; i < 2; i++) {
-		val = ocotp[i * 4];
+		val = ocotp[i];
 		mx28_fec_pdata[i].mac[0] = 0x00;
 		mx28_fec_pdata[i].mac[1] = 0x04;
 		mx28_fec_pdata[i].mac[2] = 0x9f;
@@ -295,10 +269,6 @@
 	}
 
 	return 0;
-
-error:
-	pr_err("%s: timeout when reading fec mac from OCOTP\n", __func__);
-	return -ETIMEDOUT;
 }
 
 /*
@@ -417,9 +387,14 @@
 static void __init mx28evk_add_regulators(void) {}
 #endif
 
-static struct gpio mx28evk_lcd_gpios[] = {
+static const struct gpio mx28evk_gpios[] __initconst = {
 	{ MX28EVK_LCD_ENABLE, GPIOF_OUT_INIT_HIGH, "lcd-enable" },
 	{ MX28EVK_BL_ENABLE, GPIOF_OUT_INIT_HIGH, "bl-enable" },
+	{ MX28EVK_FLEXCAN_SWITCH, GPIOF_DIR_OUT, "flexcan-switch" },
+	{ MX28EVK_MMC0_SLOT_POWER, GPIOF_OUT_INIT_LOW, "mmc0-slot-power" },
+	{ MX28EVK_MMC1_SLOT_POWER, GPIOF_OUT_INIT_LOW, "mmc1-slot-power" },
+	{ MX28EVK_FEC_PHY_POWER, GPIOF_OUT_INIT_LOW, "fec-phy-power" },
+	{ MX28EVK_FEC_PHY_RESET, GPIOF_DIR_OUT, "fec-phy-reset" },
 };
 
 static const struct mxs_saif_platform_data
@@ -447,25 +422,18 @@
 	if (mx28evk_fec_get_mac())
 		pr_warn("%s: failed on fec mac setup\n", __func__);
 
+	ret = gpio_request_array(mx28evk_gpios, ARRAY_SIZE(mx28evk_gpios));
+	if (ret)
+		pr_err("One or more GPIOs failed to be requested: %d\n", ret);
+
 	mx28evk_fec_reset();
 	mx28_add_fec(0, &mx28_fec_pdata[0]);
 	mx28_add_fec(1, &mx28_fec_pdata[1]);
 
-	ret = gpio_request_one(MX28EVK_FLEXCAN_SWITCH, GPIOF_DIR_OUT,
-				"flexcan-switch");
-	if (ret) {
-		pr_err("failed to request gpio flexcan-switch: %d\n", ret);
-	} else {
-		mx28_add_flexcan(0, &mx28evk_flexcan_pdata[0]);
-		mx28_add_flexcan(1, &mx28evk_flexcan_pdata[1]);
-	}
+	mx28_add_flexcan(0, &mx28evk_flexcan_pdata[0]);
+	mx28_add_flexcan(1, &mx28evk_flexcan_pdata[1]);
 
-	ret = gpio_request_array(mx28evk_lcd_gpios,
-				 ARRAY_SIZE(mx28evk_lcd_gpios));
-	if (ret)
-		pr_warn("failed to request gpio pins for lcd: %d\n", ret);
-	else
-		mx28_add_mxsfb(&mx28evk_mxsfb_pdata);
+	mx28_add_mxsfb(&mx28evk_mxsfb_pdata);
 
 	mxs_saif_clkmux_select(MXS_DIGCTL_SAIF_CLKMUX_EXTMSTR0);
 	mx28_add_saif(0, &mx28evk_mxs_saif_pdata[0]);
@@ -480,20 +448,8 @@
 	mxs_add_platform_device("mxs-sgtl5000", 0, NULL, 0,
 			NULL, 0);
 
-	/* power on mmc slot by writing 0 to the gpio */
-	ret = gpio_request_one(MX28EVK_MMC0_SLOT_POWER, GPIOF_OUT_INIT_LOW,
-			       "mmc0-slot-power");
-	if (ret)
-		pr_warn("failed to request gpio mmc0-slot-power: %d\n", ret);
-	else
-		mx28_add_mxs_mmc(0, &mx28evk_mmc_pdata[0]);
-
-	ret = gpio_request_one(MX28EVK_MMC1_SLOT_POWER, GPIOF_OUT_INIT_LOW,
-			       "mmc1-slot-power");
-	if (ret)
-		pr_warn("failed to request gpio mmc1-slot-power: %d\n", ret);
-	else
-		mx28_add_mxs_mmc(1, &mx28evk_mmc_pdata[1]);
+	mx28_add_mxs_mmc(0, &mx28evk_mmc_pdata[0]);
+	mx28_add_mxs_mmc(1, &mx28evk_mmc_pdata[1]);
 
 	mx28_add_rtc_stmp3xxx();
 
diff --git a/arch/arm/mach-mxs/pm.c b/arch/arm/mach-mxs/pm.c
index fb042da..a9b4bbc 100644
--- a/arch/arm/mach-mxs/pm.c
+++ b/arch/arm/mach-mxs/pm.c
@@ -15,13 +15,12 @@
 #include <linux/kernel.h>
 #include <linux/suspend.h>
 #include <linux/io.h>
-#include <mach/system.h>
 
 static int mxs_suspend_enter(suspend_state_t state)
 {
 	switch (state) {
 	case PM_SUSPEND_MEM:
-		arch_idle();
+		cpu_do_idle();
 		break;
 
 	default:
diff --git a/arch/arm/mach-netx/fb.c b/arch/arm/mach-netx/fb.c
index b991323..2cdf6ef 100644
--- a/arch/arm/mach-netx/fb.c
+++ b/arch/arm/mach-netx/fb.c
@@ -92,18 +92,7 @@
 {
 }
 
-static struct amba_device fb_device = {
-	.dev		= {
-		.init_name = "fb",
-		.coherent_dma_mask = ~0,
-	},
-	.res		= {
-		.start	= 0x00104000,
-		.end	= 0x00104fff,
-		.flags	= IORESOURCE_MEM,
-	},
-	.irq		= { NETX_IRQ_LCD, NO_IRQ },
-};
+static AMBA_AHB_DEVICE(fb, "fb", 0, 0x00104000, { NETX_IRQ_LCD }, NULL);
 
 int netx_fb_init(struct clcd_board *board, struct clcd_panel *panel)
 {
diff --git a/arch/arm/mach-netx/include/mach/system.h b/arch/arm/mach-netx/include/mach/system.h
deleted file mode 100644
index b38fa36..0000000
--- a/arch/arm/mach-netx/include/mach/system.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/*
- * arch/arm/mach-netx/include/mach/system.h
- *
- * Copyright (C) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2
- * as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
-
-#endif
-
diff --git a/arch/arm/mach-nomadik/board-nhk8815.c b/arch/arm/mach-nomadik/board-nhk8815.c
index 7c878bf..f6f74ad 100644
--- a/arch/arm/mach-nomadik/board-nhk8815.c
+++ b/arch/arm/mach-nomadik/board-nhk8815.c
@@ -185,20 +185,11 @@
 #endif
 }
 
-#define __MEM_4K_RESOURCE(x) \
-	.res = {.start = (x), .end = (x) + SZ_4K - 1, .flags = IORESOURCE_MEM}
+static AMBA_APB_DEVICE(uart0, "uart0", 0, NOMADIK_UART0_BASE,
+	{ IRQ_UART0 }, NULL);
 
-static struct amba_device uart0_device = {
-	.dev = { .init_name = "uart0" },
-	__MEM_4K_RESOURCE(NOMADIK_UART0_BASE),
-	.irq = {IRQ_UART0, NO_IRQ},
-};
-
-static struct amba_device uart1_device = {
-	.dev = { .init_name = "uart1" },
-	__MEM_4K_RESOURCE(NOMADIK_UART1_BASE),
-	.irq = {IRQ_UART1, NO_IRQ},
-};
+static AMBA_APB_DEVICE(uart1, "uart1", 0, NOMADIK_UART1_BASE,
+	{ IRQ_UART1 }, NULL);
 
 static struct amba_device *amba_devs[] __initdata = {
 	&uart0_device,
diff --git a/arch/arm/mach-nomadik/cpu-8815.c b/arch/arm/mach-nomadik/cpu-8815.c
index 65df7b4..27f43a4 100644
--- a/arch/arm/mach-nomadik/cpu-8815.c
+++ b/arch/arm/mach-nomadik/cpu-8815.c
@@ -97,12 +97,7 @@
 	GPIO_DEVICE(3),
 };
 
-static struct amba_device cpu8815_amba_rng = {
-	.dev = {
-		.init_name = "rng",
-	},
-	__MEM_4K_RESOURCE(NOMADIK_RNG_BASE),
-};
+static AMBA_APB_DEVICE(cpu8815_amba_rng, "rng", 0, NOMADIK_RNG_BASE, { }, NULL);
 
 static struct platform_device *platform_devs[] __initdata = {
 	cpu8815_platform_gpio + 0,
@@ -112,7 +107,7 @@
 };
 
 static struct amba_device *amba_devs[] __initdata = {
-	&cpu8815_amba_rng
+	&cpu8815_amba_rng_device
 };
 
 static int __init cpu8815_init(void)
diff --git a/arch/arm/mach-nomadik/include/mach/system.h b/arch/arm/mach-nomadik/include/mach/system.h
deleted file mode 100644
index 25e198b..0000000
--- a/arch/arm/mach-nomadik/include/mach/system.h
+++ /dev/null
@@ -1,32 +0,0 @@
-/*
- *  mach-nomadik/include/mach/system.h
- *
- *  Copyright (C) 2008 STMicroelectronics
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-	/*
-	 * This should do all the clock switching
-	 * and wait for interrupt tricks
-	 */
-	cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-omap1/Kconfig b/arch/arm/mach-omap1/Kconfig
index 4f8d66f..4b6a774 100644
--- a/arch/arm/mach-omap1/Kconfig
+++ b/arch/arm/mach-omap1/Kconfig
@@ -155,6 +155,10 @@
 	bool "Amstrad E3 (Delta)"
 	depends on ARCH_OMAP1 && ARCH_OMAP15XX
 	select FIQ
+	select GPIO_GENERIC_PLATFORM
+	select LEDS_GPIO_REGISTER
+	select REGULATOR
+	select REGULATOR_FIXED_VOLTAGE
 	help
 	  Support for the Amstrad E3 (codename Delta) videophone. Say Y here
 	  if you have such a device.
diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c
index 88909cc..cb6afe6 100644
--- a/arch/arm/mach-omap1/board-ams-delta.c
+++ b/arch/arm/mach-omap1/board-ams-delta.c
@@ -11,6 +11,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
+#include <linux/basic_mmio_gpio.h>
 #include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -18,6 +19,9 @@
 #include <linux/interrupt.h>
 #include <linux/leds.h>
 #include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/serial_8250.h>
 #include <linux/export.h>
 
@@ -40,9 +44,6 @@
 
 #include <mach/ams-delta-fiq.h>
 
-static u8 ams_delta_latch1_reg;
-static u16 ams_delta_latch2_reg;
-
 static const unsigned int ams_delta_keymap[] = {
 	KEY(0, 0, KEY_F1),		/* Advert    */
 
@@ -121,49 +122,42 @@
 	KEY(7, 3, KEY_LEFTCTRL),	/* Vol down  */
 };
 
-void ams_delta_latch1_write(u8 mask, u8 value)
-{
-	ams_delta_latch1_reg &= ~mask;
-	ams_delta_latch1_reg |= value;
-	*(volatile __u8 *) AMS_DELTA_LATCH1_VIRT = ams_delta_latch1_reg;
-}
-
-void ams_delta_latch2_write(u16 mask, u16 value)
-{
-	ams_delta_latch2_reg &= ~mask;
-	ams_delta_latch2_reg |= value;
-	*(volatile __u16 *) AMS_DELTA_LATCH2_VIRT = ams_delta_latch2_reg;
-}
+#define LATCH1_PHYS	0x01000000
+#define LATCH1_VIRT	0xEA000000
+#define MODEM_PHYS	0x04000000
+#define MODEM_VIRT	0xEB000000
+#define LATCH2_PHYS	0x08000000
+#define LATCH2_VIRT	0xEC000000
 
 static struct map_desc ams_delta_io_desc[] __initdata = {
 	/* AMS_DELTA_LATCH1 */
 	{
-		.virtual	= AMS_DELTA_LATCH1_VIRT,
-		.pfn		= __phys_to_pfn(AMS_DELTA_LATCH1_PHYS),
+		.virtual	= LATCH1_VIRT,
+		.pfn		= __phys_to_pfn(LATCH1_PHYS),
 		.length		= 0x01000000,
 		.type		= MT_DEVICE
 	},
 	/* AMS_DELTA_LATCH2 */
 	{
-		.virtual	= AMS_DELTA_LATCH2_VIRT,
-		.pfn		= __phys_to_pfn(AMS_DELTA_LATCH2_PHYS),
+		.virtual	= LATCH2_VIRT,
+		.pfn		= __phys_to_pfn(LATCH2_PHYS),
 		.length		= 0x01000000,
 		.type		= MT_DEVICE
 	},
 	/* AMS_DELTA_MODEM */
 	{
-		.virtual	= AMS_DELTA_MODEM_VIRT,
-		.pfn		= __phys_to_pfn(AMS_DELTA_MODEM_PHYS),
+		.virtual	= MODEM_VIRT,
+		.pfn		= __phys_to_pfn(MODEM_PHYS),
 		.length		= 0x01000000,
 		.type		= MT_DEVICE
 	}
 };
 
-static struct omap_lcd_config ams_delta_lcd_config = {
+static struct omap_lcd_config ams_delta_lcd_config __initdata = {
 	.ctrl_name	= "internal",
 };
 
-static struct omap_usb_config ams_delta_usb_config __initdata = {
+static struct omap_usb_config ams_delta_usb_config = {
 	.register_host	= 1,
 	.hmc_mode	= 16,
 	.pins[0]	= 2,
@@ -173,6 +167,147 @@
 	{ OMAP_TAG_LCD,		&ams_delta_lcd_config },
 };
 
+#define LATCH1_GPIO_BASE	232
+#define LATCH1_NGPIO		8
+
+static struct resource latch1_resources[] = {
+	[0] = {
+		.name	= "dat",
+		.start	= LATCH1_PHYS,
+		.end	= LATCH1_PHYS + (LATCH1_NGPIO - 1) / 8,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct bgpio_pdata latch1_pdata = {
+	.base	= LATCH1_GPIO_BASE,
+	.ngpio	= LATCH1_NGPIO,
+};
+
+static struct platform_device latch1_gpio_device = {
+	.name		= "basic-mmio-gpio",
+	.id		= 0,
+	.resource	= latch1_resources,
+	.num_resources	= ARRAY_SIZE(latch1_resources),
+	.dev		= {
+		.platform_data	= &latch1_pdata,
+	},
+};
+
+static struct resource latch2_resources[] = {
+	[0] = {
+		.name	= "dat",
+		.start	= LATCH2_PHYS,
+		.end	= LATCH2_PHYS + (AMS_DELTA_LATCH2_NGPIO - 1) / 8,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct bgpio_pdata latch2_pdata = {
+	.base	= AMS_DELTA_LATCH2_GPIO_BASE,
+	.ngpio	= AMS_DELTA_LATCH2_NGPIO,
+};
+
+static struct platform_device latch2_gpio_device = {
+	.name		= "basic-mmio-gpio",
+	.id		= 1,
+	.resource	= latch2_resources,
+	.num_resources	= ARRAY_SIZE(latch2_resources),
+	.dev		= {
+		.platform_data	= &latch2_pdata,
+	},
+};
+
+static const struct gpio latch_gpios[] __initconst = {
+	{
+		.gpio	= LATCH1_GPIO_BASE + 6,
+		.flags	= GPIOF_OUT_INIT_LOW,
+		.label	= "dockit1",
+	},
+	{
+		.gpio	= LATCH1_GPIO_BASE + 7,
+		.flags	= GPIOF_OUT_INIT_LOW,
+		.label	= "dockit2",
+	},
+	{
+		.gpio	= AMS_DELTA_GPIO_PIN_SCARD_RSTIN,
+		.flags	= GPIOF_OUT_INIT_LOW,
+		.label	= "scard_rstin",
+	},
+	{
+		.gpio	= AMS_DELTA_GPIO_PIN_SCARD_CMDVCC,
+		.flags	= GPIOF_OUT_INIT_LOW,
+		.label	= "scard_cmdvcc",
+	},
+	{
+		.gpio	= AMS_DELTA_GPIO_PIN_MODEM_CODEC,
+		.flags	= GPIOF_OUT_INIT_LOW,
+		.label	= "modem_codec",
+	},
+	{
+		.gpio	= AMS_DELTA_LATCH2_GPIO_BASE + 14,
+		.flags	= GPIOF_OUT_INIT_LOW,
+		.label	= "hookflash1",
+	},
+	{
+		.gpio	= AMS_DELTA_LATCH2_GPIO_BASE + 15,
+		.flags	= GPIOF_OUT_INIT_LOW,
+		.label	= "hookflash2",
+	},
+};
+
+static struct regulator_consumer_supply modem_nreset_consumers[] = {
+	REGULATOR_SUPPLY("RESET#", "serial8250.1"),
+	REGULATOR_SUPPLY("POR", "cx20442-codec"),
+};
+
+static struct regulator_init_data modem_nreset_data = {
+	.constraints		= {
+		.valid_ops_mask		= REGULATOR_CHANGE_STATUS,
+		.boot_on		= 1,
+	},
+	.num_consumer_supplies	= ARRAY_SIZE(modem_nreset_consumers),
+	.consumer_supplies	= modem_nreset_consumers,
+};
+
+static struct fixed_voltage_config modem_nreset_config = {
+	.supply_name		= "modem_nreset",
+	.microvolts		= 3300000,
+	.gpio			= AMS_DELTA_GPIO_PIN_MODEM_NRESET,
+	.startup_delay		= 25000,
+	.enable_high		= 1,
+	.enabled_at_boot	= 1,
+	.init_data		= &modem_nreset_data,
+};
+
+static struct platform_device modem_nreset_device = {
+	.name	= "reg-fixed-voltage",
+	.id	= -1,
+	.dev	= {
+		.platform_data	= &modem_nreset_config,
+	},
+};
+
+struct modem_private_data {
+	struct regulator *regulator;
+};
+
+static struct modem_private_data modem_priv;
+
+void ams_delta_latch_write(int base, int ngpio, u16 mask, u16 value)
+{
+	int bit = 0;
+	u16 bitpos = 1 << bit;
+
+	for (; bit < ngpio; bit++, bitpos = bitpos << 1) {
+		if (!(mask & bitpos))
+			continue;
+		else
+			gpio_set_value(base + bit, (value & bitpos) != 0);
+	}
+}
+EXPORT_SYMBOL(ams_delta_latch_write);
+
 static struct resource ams_delta_nand_resources[] = {
 	[0] = {
 		.start	= OMAP1_MPUIO_BASE,
@@ -202,7 +337,7 @@
 	.keymap_size	= ARRAY_SIZE(ams_delta_keymap),
 };
 
-static struct omap_kp_platform_data ams_delta_kp_data __initdata = {
+static struct omap_kp_platform_data ams_delta_kp_data = {
 	.rows		= 8,
 	.cols		= 8,
 	.keymap_data	= &ams_delta_keymap_data,
@@ -224,9 +359,45 @@
 	.id	= -1,
 };
 
-static struct platform_device ams_delta_led_device = {
-	.name	= "ams-delta-led",
-	.id	= -1
+static const struct gpio_led gpio_leds[] __initconst = {
+	{
+		.name		 = "camera",
+		.gpio		 = LATCH1_GPIO_BASE + 0,
+		.default_state	 = LEDS_GPIO_DEFSTATE_OFF,
+#ifdef CONFIG_LEDS_TRIGGERS
+		.default_trigger = "ams_delta_camera",
+#endif
+	},
+	{
+		.name		 = "advert",
+		.gpio		 = LATCH1_GPIO_BASE + 1,
+		.default_state	 = LEDS_GPIO_DEFSTATE_OFF,
+	},
+	{
+		.name		 = "email",
+		.gpio		 = LATCH1_GPIO_BASE + 2,
+		.default_state	 = LEDS_GPIO_DEFSTATE_OFF,
+	},
+	{
+		.name		 = "handsfree",
+		.gpio		 = LATCH1_GPIO_BASE + 3,
+		.default_state	 = LEDS_GPIO_DEFSTATE_OFF,
+	},
+	{
+		.name		 = "voicemail",
+		.gpio		 = LATCH1_GPIO_BASE + 4,
+		.default_state	 = LEDS_GPIO_DEFSTATE_OFF,
+	},
+	{
+		.name		 = "voice",
+		.gpio		 = LATCH1_GPIO_BASE + 5,
+		.default_state	 = LEDS_GPIO_DEFSTATE_OFF,
+	},
+};
+
+static const struct gpio_led_platform_data leds_pdata __initconst = {
+	.leds		= gpio_leds,
+	.num_leds	= ARRAY_SIZE(gpio_leds),
 };
 
 static struct i2c_board_info ams_delta_camera_board_info[] = {
@@ -275,13 +446,17 @@
 };
 
 static struct platform_device *ams_delta_devices[] __initdata = {
-	&ams_delta_nand_device,
+	&latch1_gpio_device,
+	&latch2_gpio_device,
 	&ams_delta_kp_device,
-	&ams_delta_lcd_device,
-	&ams_delta_led_device,
 	&ams_delta_camera_device,
 };
 
+static struct platform_device *late_devices[] __initdata = {
+	&ams_delta_nand_device,
+	&ams_delta_lcd_device,
+};
+
 static void __init ams_delta_init(void)
 {
 	/* mux pins for uarts */
@@ -307,15 +482,13 @@
 	omap_serial_init();
 	omap_register_i2c_bus(1, 100, NULL, 0);
 
-	/* Clear latch2 (NAND, LCD, modem enable) */
-	ams_delta_latch2_write(~0, 0);
-
 	omap1_usb_init(&ams_delta_usb_config);
 	omap1_set_camera_info(&ams_delta_camera_platform_data);
 #ifdef CONFIG_LEDS_TRIGGERS
 	led_trigger_register_simple("ams_delta_camera",
 			&ams_delta_camera_led_trigger);
 #endif
+	gpio_led_register_device(-1, &leds_pdata);
 	platform_add_devices(ams_delta_devices, ARRAY_SIZE(ams_delta_devices));
 
 	ams_delta_init_fiq();
@@ -323,16 +496,34 @@
 	omap_writew(omap_readw(ARM_RSTCT1) | 0x0004, ARM_RSTCT1);
 }
 
+static void modem_pm(struct uart_port *port, unsigned int state, unsigned old)
+{
+	struct modem_private_data *priv = port->private_data;
+
+	if (IS_ERR(priv->regulator))
+		return;
+
+	if (state == old)
+		return;
+
+	if (state == 0)
+		regulator_enable(priv->regulator);
+	else if (old == 0)
+		regulator_disable(priv->regulator);
+}
+
 static struct plat_serial8250_port ams_delta_modem_ports[] = {
 	{
-		.membase	= IOMEM(AMS_DELTA_MODEM_VIRT),
-		.mapbase	= AMS_DELTA_MODEM_PHYS,
+		.membase	= IOMEM(MODEM_VIRT),
+		.mapbase	= MODEM_PHYS,
 		.irq		= -EINVAL, /* changed later */
 		.flags		= UPF_BOOT_AUTOCONF,
 		.irqflags	= IRQF_TRIGGER_RISING,
 		.iotype		= UPIO_MEM,
 		.regshift	= 1,
 		.uartclk	= BASE_BAUD * 16,
+		.pm		= modem_pm,
+		.private_data	= &modem_priv,
 	},
 	{ },
 };
@@ -345,13 +536,27 @@
 	},
 };
 
-static int __init ams_delta_modem_init(void)
+static int __init late_init(void)
 {
 	int err;
 
 	if (!machine_is_ams_delta())
 		return -ENODEV;
 
+	err = gpio_request_array(latch_gpios, ARRAY_SIZE(latch_gpios));
+	if (err) {
+		pr_err("Couldn't take over latch1/latch2 GPIO pins\n");
+		return err;
+	}
+
+	platform_add_devices(late_devices, ARRAY_SIZE(late_devices));
+
+	err = platform_device_register(&modem_nreset_device);
+	if (err) {
+		pr_err("Couldn't register the modem regulator device\n");
+		return err;
+	}
+
 	omap_cfg_reg(M14_1510_GPIO2);
 	ams_delta_modem_ports[0].irq =
 			gpio_to_irq(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
@@ -363,13 +568,35 @@
 	}
 	gpio_direction_input(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
 
-	ams_delta_latch2_write(
-		AMS_DELTA_LATCH2_MODEM_NRESET | AMS_DELTA_LATCH2_MODEM_CODEC,
-		AMS_DELTA_LATCH2_MODEM_NRESET | AMS_DELTA_LATCH2_MODEM_CODEC);
+	/* Initialize the modem_nreset regulator consumer before use */
+	modem_priv.regulator = ERR_PTR(-ENODEV);
 
-	return platform_device_register(&ams_delta_modem_device);
+	ams_delta_latch2_write(AMS_DELTA_LATCH2_MODEM_CODEC,
+			AMS_DELTA_LATCH2_MODEM_CODEC);
+
+	err = platform_device_register(&ams_delta_modem_device);
+	if (err)
+		goto gpio_free;
+
+	/*
+	 * Once the modem device is registered, the modem_nreset
+	 * regulator can be requested on behalf of that device.
+	 */
+	modem_priv.regulator = regulator_get(&ams_delta_modem_device.dev,
+			"RESET#");
+	if (IS_ERR(modem_priv.regulator)) {
+		err = PTR_ERR(modem_priv.regulator);
+		goto unregister;
+	}
+	return 0;
+
+unregister:
+	platform_device_unregister(&ams_delta_modem_device);
+gpio_free:
+	gpio_free(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
+	return err;
 }
-arch_initcall(ams_delta_modem_init);
+late_initcall(late_init);
 
 static void __init ams_delta_map_io(void)
 {
@@ -388,6 +615,3 @@
 	.timer		= &omap1_timer,
 	.restart	= omap1_restart,
 MACHINE_END
-
-EXPORT_SYMBOL(ams_delta_latch1_write);
-EXPORT_SYMBOL(ams_delta_latch2_write);
diff --git a/arch/arm/mach-omap1/include/mach/system.h b/arch/arm/mach-omap1/include/mach/system.h
deleted file mode 100644
index a6c1b3a..0000000
--- a/arch/arm/mach-omap1/include/mach/system.h
+++ /dev/null
@@ -1,5 +0,0 @@
-/*
- * arch/arm/mach-omap1/include/mach/system.h
- */
-
-#include <plat/system.h>
diff --git a/arch/arm/mach-omap1/pm.c b/arch/arm/mach-omap1/pm.c
index 89ea20c..0c2c366 100644
--- a/arch/arm/mach-omap1/pm.c
+++ b/arch/arm/mach-omap1/pm.c
@@ -42,9 +42,9 @@
 #include <linux/sysfs.h>
 #include <linux/module.h>
 #include <linux/io.h>
+#include <linux/atomic.h>
 
 #include <asm/irq.h>
-#include <linux/atomic.h>
 #include <asm/mach/time.h>
 #include <asm/mach/irq.h>
 
@@ -108,13 +108,7 @@
 	__u32 use_idlect1 = arm_idlect1_mask;
 	int do_sleep = 0;
 
-	local_irq_disable();
 	local_fiq_disable();
-	if (need_resched()) {
-		local_fiq_enable();
-		local_irq_enable();
-		return;
-	}
 
 #if defined(CONFIG_OMAP_MPU_TIMER) && !defined(CONFIG_OMAP_DM_TIMER)
 #warning Enable 32kHz OS timer in order to allow sleep states in idle
@@ -157,14 +151,12 @@
 		omap_writel(saved_idlect1, ARM_IDLECT1);
 
 		local_fiq_enable();
-		local_irq_enable();
 		return;
 	}
 	omap_sram_suspend(omap_readl(ARM_IDLECT1),
 			  omap_readl(ARM_IDLECT2));
 
 	local_fiq_enable();
-	local_irq_enable();
 }
 
 /*
@@ -583,8 +575,6 @@
 
 #endif /* DEBUG && CONFIG_PROC_FS */
 
-static void (*saved_idle)(void) = NULL;
-
 /*
  *	omap_pm_prepare - Do preliminary suspend work.
  *
@@ -592,8 +582,7 @@
 static int omap_pm_prepare(void)
 {
 	/* We cannot sleep in idle until we have resumed */
-	saved_idle = pm_idle;
-	pm_idle = NULL;
+	disable_hlt();
 
 	return 0;
 }
@@ -630,7 +619,7 @@
 
 static void omap_pm_finish(void)
 {
-	pm_idle = saved_idle;
+	enable_hlt();
 }
 
 
@@ -687,7 +676,7 @@
 		return -ENODEV;
 	}
 
-	pm_idle = omap1_pm_idle;
+	arm_pm_idle = omap1_pm_idle;
 
 	if (cpu_is_omap7xx())
 		setup_irq(INT_7XX_WAKE_UP_REQ, &omap_wakeup_irq);
diff --git a/arch/arm/mach-omap2/emu.c b/arch/arm/mach-omap2/emu.c
index 9c442e2..ce91aad 100644
--- a/arch/arm/mach-omap2/emu.c
+++ b/arch/arm/mach-omap2/emu.c
@@ -30,29 +30,8 @@
 #define ETB_BASE	(L4_EMU_34XX_PHYS + 0x1b000)
 #define DAPCTL		(L4_EMU_34XX_PHYS + 0x1d000)
 
-static struct amba_device omap3_etb_device = {
-	.dev		= {
-		.init_name = "etb",
-	},
-	.res		= {
-		.start	= ETB_BASE,
-		.end	= ETB_BASE + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	.periphid	= 0x000bb907,
-};
-
-static struct amba_device omap3_etm_device = {
-	.dev		= {
-		.init_name = "etm",
-	},
-	.res		= {
-		.start	= ETM_BASE,
-		.end	= ETM_BASE + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	.periphid	= 0x102bb921,
-};
+static AMBA_APB_DEVICE(omap3_etb, "etb", 0x000bb907, ETB_BASE, { }, NULL);
+static AMBA_APB_DEVICE(omap3_etm, "etm", 0x102bb921, ETM_BASE, { }, NULL);
 
 static int __init emu_init(void)
 {
@@ -66,4 +45,3 @@
 }
 
 subsys_initcall(emu_init);
-
diff --git a/arch/arm/mach-omap2/include/mach/system.h b/arch/arm/mach-omap2/include/mach/system.h
deleted file mode 100644
index d488721..0000000
--- a/arch/arm/mach-omap2/include/mach/system.h
+++ /dev/null
@@ -1,5 +0,0 @@
-/*
- * arch/arm/mach-omap2/include/mach/system.h
- */
-
-#include <plat/system.h>
diff --git a/arch/arm/mach-omap2/pm24xx.c b/arch/arm/mach-omap2/pm24xx.c
index 23de98d..a4eb5c2 100644
--- a/arch/arm/mach-omap2/pm24xx.c
+++ b/arch/arm/mach-omap2/pm24xx.c
@@ -226,7 +226,6 @@
 
 static void omap2_pm_idle(void)
 {
-	local_irq_disable();
 	local_fiq_disable();
 
 	if (!omap2_can_sleep()) {
@@ -243,7 +242,6 @@
 
 out:
 	local_fiq_enable();
-	local_irq_enable();
 }
 
 #ifdef CONFIG_SUSPEND
@@ -462,7 +460,7 @@
 	}
 
 	suspend_set_ops(&omap_pm_ops);
-	pm_idle = omap2_pm_idle;
+	arm_pm_idle = omap2_pm_idle;
 
 	return 0;
 }
diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index fc69875..b77df73 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -418,10 +418,9 @@
 
 static void omap3_pm_idle(void)
 {
-	local_irq_disable();
 	local_fiq_disable();
 
-	if (omap_irq_pending() || need_resched())
+	if (omap_irq_pending())
 		goto out;
 
 	trace_power_start(POWER_CSTATE, 1, smp_processor_id());
@@ -434,7 +433,6 @@
 
 out:
 	local_fiq_enable();
-	local_irq_enable();
 }
 
 #ifdef CONFIG_SUSPEND
@@ -848,7 +846,7 @@
 	suspend_set_ops(&omap_pm_ops);
 #endif /* CONFIG_SUSPEND */
 
-	pm_idle = omap3_pm_idle;
+	arm_pm_idle = omap3_pm_idle;
 	omap3_idle_init();
 
 	/*
diff --git a/arch/arm/mach-omap2/pm44xx.c b/arch/arm/mach-omap2/pm44xx.c
index c264ef7..c840689 100644
--- a/arch/arm/mach-omap2/pm44xx.c
+++ b/arch/arm/mach-omap2/pm44xx.c
@@ -173,18 +173,16 @@
  * omap_default_idle - OMAP4 default ilde routine.'
  *
  * Implements OMAP4 memory, IO ordering requirements which can't be addressed
- * with default arch_idle() hook. Used by all CPUs with !CONFIG_CPUIDLE and
+ * with default cpu_do_idle() hook. Used by all CPUs with !CONFIG_CPUIDLE and
  * by secondary CPU with CONFIG_CPUIDLE.
  */
 static void omap_default_idle(void)
 {
-	local_irq_disable();
 	local_fiq_disable();
 
 	omap_do_wfi();
 
 	local_fiq_enable();
-	local_irq_enable();
 }
 
 /**
@@ -255,8 +253,8 @@
 	suspend_set_ops(&omap_pm_ops);
 #endif /* CONFIG_SUSPEND */
 
-	/* Overwrite the default arch_idle() */
-	pm_idle = omap_default_idle;
+	/* Overwrite the default cpu_do_idle() */
+	arm_pm_idle = omap_default_idle;
 
 	omap4_idle_init();
 
diff --git a/arch/arm/mach-omap2/prm_common.c b/arch/arm/mach-omap2/prm_common.c
index 860118a..873b51d 100644
--- a/arch/arm/mach-omap2/prm_common.c
+++ b/arch/arm/mach-omap2/prm_common.c
@@ -24,7 +24,6 @@
 #include <linux/interrupt.h>
 #include <linux/slab.h>
 
-#include <mach/system.h>
 #include <plat/common.h>
 #include <plat/prcm.h>
 #include <plat/irqs.h>
diff --git a/arch/arm/mach-orion5x/include/mach/system.h b/arch/arm/mach-orion5x/include/mach/system.h
deleted file mode 100644
index 825a265..0000000
--- a/arch/arm/mach-orion5x/include/mach/system.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- * arch/arm/mach-orion5x/include/mach/system.h
- *
- * Tzachi Perelstein <tzachi@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-picoxcell/include/mach/system.h b/arch/arm/mach-picoxcell/include/mach/system.h
deleted file mode 100644
index 1a5d8cb..0000000
--- a/arch/arm/mach-picoxcell/include/mach/system.h
+++ /dev/null
@@ -1,26 +0,0 @@
-/*
- * Copyright (c) 2011 Picochip Ltd., Jamie Iles
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-	/*
-	 * This should do all the clock switching and wait for interrupt
-	 * tricks.
-	 */
-	cpu_do_idle();
-}
-
-#endif /* __ASM_ARCH_SYSTEM_H */
diff --git a/arch/arm/mach-pnx4008/include/mach/system.h b/arch/arm/mach-pnx4008/include/mach/system.h
deleted file mode 100644
index 60cfe71..0000000
--- a/arch/arm/mach-pnx4008/include/mach/system.h
+++ /dev/null
@@ -1,29 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/include/mach/system.h
- *
- * Copyright (C) 2003 Philips Semiconductors
- * Copyright (C) 2005 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static void arch_idle(void)
-{
-	cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-prima2/include/mach/system.h b/arch/arm/mach-prima2/include/mach/system.h
deleted file mode 100644
index 2c7d2a9..0000000
--- a/arch/arm/mach-prima2/include/mach/system.h
+++ /dev/null
@@ -1,17 +0,0 @@
-/*
- * arch/arm/mach-prima2/include/mach/system.h
- *
- * Copyright (c) 2011 Cambridge Silicon Radio Limited, a CSR plc group company.
- *
- * Licensed under GPLv2 or later.
- */
-
-#ifndef __MACH_SYSTEM_H__
-#define __MACH_SYSTEM_H__
-
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-pxa/hx4700.c b/arch/arm/mach-pxa/hx4700.c
index 208eef1..f2c23ea 100644
--- a/arch/arm/mach-pxa/hx4700.c
+++ b/arch/arm/mach-pxa/hx4700.c
@@ -245,6 +245,21 @@
 	ASIC3_GPIOD15_nPIOW,
 };
 
+static struct asic3_led asic3_leds[ASIC3_NUM_LEDS] = {
+	[0] = {
+		.name = "hx4700:amber",
+		.default_trigger = "ds2760-battery.0-charging-blink-full-solid",
+	},
+	[1] = {
+		.name = "hx4700:green",
+		.default_trigger = "unused",
+	},
+	[2] = {
+		.name = "hx4700:blue",
+		.default_trigger = "hx4700-radio",
+	},
+};
+
 static struct resource asic3_resources[] = {
 	/* GPIO part */
 	[0] = {
@@ -275,6 +290,7 @@
 	.gpio_config_num = ARRAY_SIZE(asic3_gpio_config),
 	.irq_base        = IRQ_BOARD_START,
 	.gpio_base       = HX4700_ASIC3_GPIO_BASE,
+	.leds            = asic3_leds,
 };
 
 static struct platform_device asic3 = {
@@ -705,10 +721,9 @@
 	gpio_set_value(GPIO91_HX4700_FLASH_VPEN, vpp);
 }
 
-static struct resource strataflash_resource = {
-	.start = PXA_CS0_PHYS,
-	.end   = PXA_CS0_PHYS + SZ_128M - 1,
-	.flags = IORESOURCE_MEM,
+static struct resource strataflash_resource[] = {
+	[0] = DEFINE_RES_MEM(PXA_CS0_PHYS, SZ_64M),
+	[1] = DEFINE_RES_MEM(PXA_CS0_PHYS + SZ_64M, SZ_64M),
 };
 
 static struct physmap_flash_data strataflash_data = {
@@ -719,8 +734,8 @@
 static struct platform_device strataflash = {
 	.name          = "physmap-flash",
 	.id            = -1,
-	.resource      = &strataflash_resource,
-	.num_resources = 1,
+	.resource      = strataflash_resource,
+	.num_resources = ARRAY_SIZE(strataflash_resource),
 	.dev = {
 		.platform_data = &strataflash_data,
 	},
diff --git a/arch/arm/mach-pxa/include/mach/system.h b/arch/arm/mach-pxa/include/mach/system.h
deleted file mode 100644
index c5afacd..0000000
--- a/arch/arm/mach-pxa/include/mach/system.h
+++ /dev/null
@@ -1,15 +0,0 @@
-/*
- * arch/arm/mach-pxa/include/mach/system.h
- *
- * Author:	Nicolas Pitre
- * Created:	Jun 15, 2001
- * Copyright:	MontaVista Software Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
diff --git a/arch/arm/mach-pxa/pxa25x.c b/arch/arm/mach-pxa/pxa25x.c
index 00d6eac..d8de3e5 100644
--- a/arch/arm/mach-pxa/pxa25x.c
+++ b/arch/arm/mach-pxa/pxa25x.c
@@ -208,6 +208,7 @@
 	INIT_CLKREG(&clk_pxa25x_gpio11, NULL, "GPIO11_CLK"),
 	INIT_CLKREG(&clk_pxa25x_gpio12, NULL, "GPIO12_CLK"),
 	INIT_CLKREG(&clk_pxa25x_mem, "pxa2xx-pcmcia", NULL),
+	INIT_CLKREG(&clk_dummy, "pxa-gpio", NULL),
 };
 
 static struct clk_lookup pxa25x_hwuart_clkreg =
diff --git a/arch/arm/mach-pxa/pxa27x.c b/arch/arm/mach-pxa/pxa27x.c
index c1673b3..a3fabc9 100644
--- a/arch/arm/mach-pxa/pxa27x.c
+++ b/arch/arm/mach-pxa/pxa27x.c
@@ -229,6 +229,7 @@
 	INIT_CLKREG(&clk_pxa27x_im, NULL, "IMCLK"),
 	INIT_CLKREG(&clk_pxa27x_memc, NULL, "MEMCLK"),
 	INIT_CLKREG(&clk_pxa27x_mem, "pxa2xx-pcmcia", NULL),
+	INIT_CLKREG(&clk_dummy, "pxa-gpio", NULL),
 };
 
 #ifdef CONFIG_PM
diff --git a/arch/arm/mach-realview/core.h b/arch/arm/mach-realview/core.h
index 735b57a..f8f2c0a 100644
--- a/arch/arm/mach-realview/core.h
+++ b/arch/arm/mach-realview/core.h
@@ -28,21 +28,11 @@
 #include <asm/setup.h>
 #include <asm/leds.h>
 
-#define AMBA_DEVICE(name,busid,base,plat)			\
-static struct amba_device name##_device = {			\
-	.dev		= {					\
-		.coherent_dma_mask = ~0,			\
-		.init_name = busid,				\
-		.platform_data = plat,				\
-	},							\
-	.res		= {					\
-		.start	= REALVIEW_##base##_BASE,		\
-		.end	= (REALVIEW_##base##_BASE) + SZ_4K - 1,	\
-		.flags	= IORESOURCE_MEM,			\
-	},							\
-	.dma_mask	= ~0,					\
-	.irq		= base##_IRQ,				\
-}
+#define APB_DEVICE(name, busid, base, plat)			\
+static AMBA_APB_DEVICE(name, busid, 0, REALVIEW_##base##_BASE, base##_IRQ, plat)
+
+#define AHB_DEVICE(name, busid, base, plat)			\
+static AMBA_AHB_DEVICE(name, busid, 0, REALVIEW_##base##_BASE, base##_IRQ, plat)
 
 struct machine_desc;
 
diff --git a/arch/arm/mach-realview/include/mach/irqs-pb1176.h b/arch/arm/mach-realview/include/mach/irqs-pb1176.h
index 5c3c625..708f841 100644
--- a/arch/arm/mach-realview/include/mach/irqs-pb1176.h
+++ b/arch/arm/mach-realview/include/mach/irqs-pb1176.h
@@ -40,6 +40,7 @@
 #define IRQ_DC1176_L2CC		(IRQ_DC1176_GIC_START + 13)
 #define IRQ_DC1176_RTC		(IRQ_DC1176_GIC_START + 14)
 #define IRQ_DC1176_CLCD		(IRQ_DC1176_GIC_START + 15)	/* CLCD controller */
+#define IRQ_DC1176_GPIO0	(IRQ_DC1176_GIC_START + 16)
 #define IRQ_DC1176_SSP		(IRQ_DC1176_GIC_START + 17)	/* SSP port */
 #define IRQ_DC1176_UART0	(IRQ_DC1176_GIC_START + 18)	/* UART 0 on development chip */
 #define IRQ_DC1176_UART1	(IRQ_DC1176_GIC_START + 19)	/* UART 1 on development chip */
@@ -73,7 +74,6 @@
 #define IRQ_PB1176_DMAC		(IRQ_PB1176_GIC_START + 24)	/* DMA controller */
 #define IRQ_PB1176_RTC		(IRQ_PB1176_GIC_START + 25)	/* Real Time Clock */
 
-#define IRQ_PB1176_GPIO0	-1
 #define IRQ_PB1176_SCTL		-1
 
 #define NR_GIC_PB1176		2
diff --git a/arch/arm/mach-realview/include/mach/system.h b/arch/arm/mach-realview/include/mach/system.h
deleted file mode 100644
index 471b671..0000000
--- a/arch/arm/mach-realview/include/mach/system.h
+++ /dev/null
@@ -1,33 +0,0 @@
-/*
- *  arch/arm/mach-realview/include/mach/system.h
- *
- *  Copyright (C) 2003 ARM Limited
- *  Copyright (C) 2000 Deep Blue Solutions Ltd
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-	/*
-	 * This should do all the clock switching
-	 * and wait for interrupt tricks
-	 */
-	cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-realview/realview_eb.c b/arch/arm/mach-realview/realview_eb.c
index 9578145..157e1bc6 100644
--- a/arch/arm/mach-realview/realview_eb.c
+++ b/arch/arm/mach-realview/realview_eb.c
@@ -135,63 +135,63 @@
 /*
  * These devices are connected via the core APB bridge
  */
-#define GPIO2_IRQ	{ IRQ_EB_GPIO2, NO_IRQ }
-#define GPIO3_IRQ	{ IRQ_EB_GPIO3, NO_IRQ }
+#define GPIO2_IRQ	{ IRQ_EB_GPIO2 }
+#define GPIO3_IRQ	{ IRQ_EB_GPIO3 }
 
-#define AACI_IRQ	{ IRQ_EB_AACI, NO_IRQ }
+#define AACI_IRQ	{ IRQ_EB_AACI }
 #define MMCI0_IRQ	{ IRQ_EB_MMCI0A, IRQ_EB_MMCI0B }
-#define KMI0_IRQ	{ IRQ_EB_KMI0, NO_IRQ }
-#define KMI1_IRQ	{ IRQ_EB_KMI1, NO_IRQ }
+#define KMI0_IRQ	{ IRQ_EB_KMI0 }
+#define KMI1_IRQ	{ IRQ_EB_KMI1 }
 
 /*
  * These devices are connected directly to the multi-layer AHB switch
  */
-#define EB_SMC_IRQ	{ NO_IRQ, NO_IRQ }
-#define MPMC_IRQ	{ NO_IRQ, NO_IRQ }
-#define EB_CLCD_IRQ	{ IRQ_EB_CLCD, NO_IRQ }
-#define DMAC_IRQ	{ IRQ_EB_DMA, NO_IRQ }
+#define EB_SMC_IRQ	{ }
+#define MPMC_IRQ	{ }
+#define EB_CLCD_IRQ	{ IRQ_EB_CLCD }
+#define DMAC_IRQ	{ IRQ_EB_DMA }
 
 /*
  * These devices are connected via the core APB bridge
  */
-#define SCTL_IRQ	{ NO_IRQ, NO_IRQ }
-#define EB_WATCHDOG_IRQ	{ IRQ_EB_WDOG, NO_IRQ }
-#define EB_GPIO0_IRQ	{ IRQ_EB_GPIO0, NO_IRQ }
-#define GPIO1_IRQ	{ IRQ_EB_GPIO1, NO_IRQ }
-#define EB_RTC_IRQ	{ IRQ_EB_RTC, NO_IRQ }
+#define SCTL_IRQ	{ }
+#define EB_WATCHDOG_IRQ	{ IRQ_EB_WDOG }
+#define EB_GPIO0_IRQ	{ IRQ_EB_GPIO0 }
+#define GPIO1_IRQ	{ IRQ_EB_GPIO1 }
+#define EB_RTC_IRQ	{ IRQ_EB_RTC }
 
 /*
  * These devices are connected via the DMA APB bridge
  */
-#define SCI_IRQ		{ IRQ_EB_SCI, NO_IRQ }
-#define EB_UART0_IRQ	{ IRQ_EB_UART0, NO_IRQ }
-#define EB_UART1_IRQ	{ IRQ_EB_UART1, NO_IRQ }
-#define EB_UART2_IRQ	{ IRQ_EB_UART2, NO_IRQ }
-#define EB_UART3_IRQ	{ IRQ_EB_UART3, NO_IRQ }
-#define EB_SSP_IRQ	{ IRQ_EB_SSP, NO_IRQ }
+#define SCI_IRQ		{ IRQ_EB_SCI }
+#define EB_UART0_IRQ	{ IRQ_EB_UART0 }
+#define EB_UART1_IRQ	{ IRQ_EB_UART1 }
+#define EB_UART2_IRQ	{ IRQ_EB_UART2 }
+#define EB_UART3_IRQ	{ IRQ_EB_UART3 }
+#define EB_SSP_IRQ	{ IRQ_EB_SSP }
 
 /* FPGA Primecells */
-AMBA_DEVICE(aaci,  "fpga:aaci",  AACI,     NULL);
-AMBA_DEVICE(mmc0,  "fpga:mmc0",  MMCI0,    &realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0,  "fpga:kmi0",  KMI0,     NULL);
-AMBA_DEVICE(kmi1,  "fpga:kmi1",  KMI1,     NULL);
-AMBA_DEVICE(uart3, "fpga:uart3", EB_UART3, NULL);
+APB_DEVICE(aaci,  "fpga:aaci",  AACI,     NULL);
+APB_DEVICE(mmc0,  "fpga:mmc0",  MMCI0,    &realview_mmc0_plat_data);
+APB_DEVICE(kmi0,  "fpga:kmi0",  KMI0,     NULL);
+APB_DEVICE(kmi1,  "fpga:kmi1",  KMI1,     NULL);
+APB_DEVICE(uart3, "fpga:uart3", EB_UART3, NULL);
 
 /* DevChip Primecells */
-AMBA_DEVICE(smc,   "dev:smc",   EB_SMC,   NULL);
-AMBA_DEVICE(clcd,  "dev:clcd",  EB_CLCD,  &clcd_plat_data);
-AMBA_DEVICE(dmac,  "dev:dmac",  DMAC,     NULL);
-AMBA_DEVICE(sctl,  "dev:sctl",  SCTL,     NULL);
-AMBA_DEVICE(wdog,  "dev:wdog",  EB_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:gpio0", EB_GPIO0, &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:gpio1", GPIO1,    &gpio1_plat_data);
-AMBA_DEVICE(gpio2, "dev:gpio2", GPIO2,    &gpio2_plat_data);
-AMBA_DEVICE(rtc,   "dev:rtc",   EB_RTC,   NULL);
-AMBA_DEVICE(sci0,  "dev:sci0",  SCI,      NULL);
-AMBA_DEVICE(uart0, "dev:uart0", EB_UART0, NULL);
-AMBA_DEVICE(uart1, "dev:uart1", EB_UART1, NULL);
-AMBA_DEVICE(uart2, "dev:uart2", EB_UART2, NULL);
-AMBA_DEVICE(ssp0,  "dev:ssp0",  EB_SSP,   &ssp0_plat_data);
+AHB_DEVICE(smc,   "dev:smc",   EB_SMC,   NULL);
+AHB_DEVICE(clcd,  "dev:clcd",  EB_CLCD,  &clcd_plat_data);
+AHB_DEVICE(dmac,  "dev:dmac",  DMAC,     NULL);
+AHB_DEVICE(sctl,  "dev:sctl",  SCTL,     NULL);
+APB_DEVICE(wdog,  "dev:wdog",  EB_WATCHDOG, NULL);
+APB_DEVICE(gpio0, "dev:gpio0", EB_GPIO0, &gpio0_plat_data);
+APB_DEVICE(gpio1, "dev:gpio1", GPIO1,    &gpio1_plat_data);
+APB_DEVICE(gpio2, "dev:gpio2", GPIO2,    &gpio2_plat_data);
+APB_DEVICE(rtc,   "dev:rtc",   EB_RTC,   NULL);
+APB_DEVICE(sci0,  "dev:sci0",  SCI,      NULL);
+APB_DEVICE(uart0, "dev:uart0", EB_UART0, NULL);
+APB_DEVICE(uart1, "dev:uart1", EB_UART1, NULL);
+APB_DEVICE(uart2, "dev:uart2", EB_UART2, NULL);
+APB_DEVICE(ssp0,  "dev:ssp0",  EB_SSP,   &ssp0_plat_data);
 
 static struct amba_device *amba_devs[] __initdata = {
 	&dmac_device,
diff --git a/arch/arm/mach-realview/realview_pb1176.c b/arch/arm/mach-realview/realview_pb1176.c
index e4abe94..b1d7caf 100644
--- a/arch/arm/mach-realview/realview_pb1176.c
+++ b/arch/arm/mach-realview/realview_pb1176.c
@@ -132,50 +132,50 @@
 /*
  * RealView PB1176 AMBA devices
  */
-#define GPIO2_IRQ	{ IRQ_PB1176_GPIO2, NO_IRQ }
-#define GPIO3_IRQ	{ IRQ_PB1176_GPIO3, NO_IRQ }
-#define AACI_IRQ	{ IRQ_PB1176_AACI, NO_IRQ }
+#define GPIO2_IRQ	{ IRQ_PB1176_GPIO2 }
+#define GPIO3_IRQ	{ IRQ_PB1176_GPIO3 }
+#define AACI_IRQ	{ IRQ_PB1176_AACI }
 #define MMCI0_IRQ	{ IRQ_PB1176_MMCI0A, IRQ_PB1176_MMCI0B }
-#define KMI0_IRQ	{ IRQ_PB1176_KMI0, NO_IRQ }
-#define KMI1_IRQ	{ IRQ_PB1176_KMI1, NO_IRQ }
-#define PB1176_SMC_IRQ	{ NO_IRQ, NO_IRQ }
-#define MPMC_IRQ	{ NO_IRQ, NO_IRQ }
-#define PB1176_CLCD_IRQ	{ IRQ_DC1176_CLCD, NO_IRQ }
-#define SCTL_IRQ	{ NO_IRQ, NO_IRQ }
-#define PB1176_WATCHDOG_IRQ	{ IRQ_DC1176_WATCHDOG, NO_IRQ }
-#define PB1176_GPIO0_IRQ	{ IRQ_PB1176_GPIO0, NO_IRQ }
-#define GPIO1_IRQ	{ IRQ_PB1176_GPIO1, NO_IRQ }
-#define PB1176_RTC_IRQ	{ IRQ_DC1176_RTC, NO_IRQ }
-#define SCI_IRQ		{ IRQ_PB1176_SCI, NO_IRQ }
-#define PB1176_UART0_IRQ	{ IRQ_DC1176_UART0, NO_IRQ }
-#define PB1176_UART1_IRQ	{ IRQ_DC1176_UART1, NO_IRQ }
-#define PB1176_UART2_IRQ	{ IRQ_DC1176_UART2, NO_IRQ }
-#define PB1176_UART3_IRQ	{ IRQ_DC1176_UART3, NO_IRQ }
-#define PB1176_UART4_IRQ	{ IRQ_PB1176_UART4, NO_IRQ }
-#define PB1176_SSP_IRQ		{ IRQ_DC1176_SSP, NO_IRQ }
+#define KMI0_IRQ	{ IRQ_PB1176_KMI0 }
+#define KMI1_IRQ	{ IRQ_PB1176_KMI1 }
+#define PB1176_SMC_IRQ	{ }
+#define MPMC_IRQ	{ }
+#define PB1176_CLCD_IRQ	{ IRQ_DC1176_CLCD }
+#define SCTL_IRQ	{ }
+#define PB1176_WATCHDOG_IRQ	{ IRQ_DC1176_WATCHDOG }
+#define PB1176_GPIO0_IRQ	{ IRQ_DC1176_GPIO0 }
+#define GPIO1_IRQ	{ IRQ_PB1176_GPIO1 }
+#define PB1176_RTC_IRQ	{ IRQ_DC1176_RTC }
+#define SCI_IRQ		{ IRQ_PB1176_SCI }
+#define PB1176_UART0_IRQ	{ IRQ_DC1176_UART0 }
+#define PB1176_UART1_IRQ	{ IRQ_DC1176_UART1 }
+#define PB1176_UART2_IRQ	{ IRQ_DC1176_UART2 }
+#define PB1176_UART3_IRQ	{ IRQ_DC1176_UART3 }
+#define PB1176_UART4_IRQ	{ IRQ_PB1176_UART4 }
+#define PB1176_SSP_IRQ		{ IRQ_DC1176_SSP }
 
 /* FPGA Primecells */
-AMBA_DEVICE(aaci,	"fpga:aaci",	AACI,		NULL);
-AMBA_DEVICE(mmc0,	"fpga:mmc0",	MMCI0,		&realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0,	"fpga:kmi0",	KMI0,		NULL);
-AMBA_DEVICE(kmi1,	"fpga:kmi1",	KMI1,		NULL);
-AMBA_DEVICE(uart4,	"fpga:uart4",	PB1176_UART4,	NULL);
+APB_DEVICE(aaci,	"fpga:aaci",	AACI,		NULL);
+APB_DEVICE(mmc0,	"fpga:mmc0",	MMCI0,		&realview_mmc0_plat_data);
+APB_DEVICE(kmi0,	"fpga:kmi0",	KMI0,		NULL);
+APB_DEVICE(kmi1,	"fpga:kmi1",	KMI1,		NULL);
+APB_DEVICE(uart4,	"fpga:uart4",	PB1176_UART4,	NULL);
 
 /* DevChip Primecells */
-AMBA_DEVICE(smc,	"dev:smc",	PB1176_SMC,	NULL);
-AMBA_DEVICE(sctl,	"dev:sctl",	SCTL,		NULL);
-AMBA_DEVICE(wdog,	"dev:wdog",	PB1176_WATCHDOG,	NULL);
-AMBA_DEVICE(gpio0,	"dev:gpio0",	PB1176_GPIO0,	&gpio0_plat_data);
-AMBA_DEVICE(gpio1,	"dev:gpio1",	GPIO1,		&gpio1_plat_data);
-AMBA_DEVICE(gpio2,	"dev:gpio2",	GPIO2,		&gpio2_plat_data);
-AMBA_DEVICE(rtc,	"dev:rtc",	PB1176_RTC,	NULL);
-AMBA_DEVICE(sci0,	"dev:sci0",	SCI,		NULL);
-AMBA_DEVICE(uart0,	"dev:uart0",	PB1176_UART0,	NULL);
-AMBA_DEVICE(uart1,	"dev:uart1",	PB1176_UART1,	NULL);
-AMBA_DEVICE(uart2,	"dev:uart2",	PB1176_UART2,	NULL);
-AMBA_DEVICE(uart3,	"dev:uart3",	PB1176_UART3,	NULL);
-AMBA_DEVICE(ssp0,	"dev:ssp0",	PB1176_SSP,	&ssp0_plat_data);
-AMBA_DEVICE(clcd,	"dev:clcd",	PB1176_CLCD,	&clcd_plat_data);
+AHB_DEVICE(smc,		"dev:smc",	PB1176_SMC,	NULL);
+AHB_DEVICE(sctl,	"dev:sctl",	SCTL,		NULL);
+APB_DEVICE(wdog,	"dev:wdog",	PB1176_WATCHDOG,	NULL);
+APB_DEVICE(gpio0,	"dev:gpio0",	PB1176_GPIO0,	&gpio0_plat_data);
+APB_DEVICE(gpio1,	"dev:gpio1",	GPIO1,		&gpio1_plat_data);
+APB_DEVICE(gpio2,	"dev:gpio2",	GPIO2,		&gpio2_plat_data);
+APB_DEVICE(rtc,		"dev:rtc",	PB1176_RTC,	NULL);
+APB_DEVICE(sci0,	"dev:sci0",	SCI,		NULL);
+APB_DEVICE(uart0,	"dev:uart0",	PB1176_UART0,	NULL);
+APB_DEVICE(uart1,	"dev:uart1",	PB1176_UART1,	NULL);
+APB_DEVICE(uart2,	"dev:uart2",	PB1176_UART2,	NULL);
+APB_DEVICE(uart3,	"dev:uart3",	PB1176_UART3,	NULL);
+APB_DEVICE(ssp0,	"dev:ssp0",	PB1176_SSP,	&ssp0_plat_data);
+AHB_DEVICE(clcd,	"dev:clcd",	PB1176_CLCD,	&clcd_plat_data);
 
 static struct amba_device *amba_devs[] __initdata = {
 	&uart0_device,
diff --git a/arch/arm/mach-realview/realview_pb11mp.c b/arch/arm/mach-realview/realview_pb11mp.c
index 2147335..ae7fe54 100644
--- a/arch/arm/mach-realview/realview_pb11mp.c
+++ b/arch/arm/mach-realview/realview_pb11mp.c
@@ -127,52 +127,52 @@
  * RealView PB11MPCore AMBA devices
  */
 
-#define GPIO2_IRQ		{ IRQ_PB11MP_GPIO2, NO_IRQ }
-#define GPIO3_IRQ		{ IRQ_PB11MP_GPIO3, NO_IRQ }
-#define AACI_IRQ		{ IRQ_TC11MP_AACI, NO_IRQ }
+#define GPIO2_IRQ		{ IRQ_PB11MP_GPIO2 }
+#define GPIO3_IRQ		{ IRQ_PB11MP_GPIO3 }
+#define AACI_IRQ		{ IRQ_TC11MP_AACI }
 #define MMCI0_IRQ		{ IRQ_TC11MP_MMCI0A, IRQ_TC11MP_MMCI0B }
-#define KMI0_IRQ		{ IRQ_TC11MP_KMI0, NO_IRQ }
-#define KMI1_IRQ		{ IRQ_TC11MP_KMI1, NO_IRQ }
-#define PB11MP_SMC_IRQ		{ NO_IRQ, NO_IRQ }
-#define MPMC_IRQ		{ NO_IRQ, NO_IRQ }
-#define PB11MP_CLCD_IRQ		{ IRQ_PB11MP_CLCD, NO_IRQ }
-#define DMAC_IRQ		{ IRQ_PB11MP_DMAC, NO_IRQ }
-#define SCTL_IRQ		{ NO_IRQ, NO_IRQ }
-#define PB11MP_WATCHDOG_IRQ	{ IRQ_PB11MP_WATCHDOG, NO_IRQ }
-#define PB11MP_GPIO0_IRQ	{ IRQ_PB11MP_GPIO0, NO_IRQ }
-#define GPIO1_IRQ		{ IRQ_PB11MP_GPIO1, NO_IRQ }
-#define PB11MP_RTC_IRQ		{ IRQ_TC11MP_RTC, NO_IRQ }
-#define SCI_IRQ			{ IRQ_PB11MP_SCI, NO_IRQ }
-#define PB11MP_UART0_IRQ	{ IRQ_TC11MP_UART0, NO_IRQ }
-#define PB11MP_UART1_IRQ	{ IRQ_TC11MP_UART1, NO_IRQ }
-#define PB11MP_UART2_IRQ	{ IRQ_PB11MP_UART2, NO_IRQ }
-#define PB11MP_UART3_IRQ	{ IRQ_PB11MP_UART3, NO_IRQ }
-#define PB11MP_SSP_IRQ		{ IRQ_PB11MP_SSP, NO_IRQ }
+#define KMI0_IRQ		{ IRQ_TC11MP_KMI0 }
+#define KMI1_IRQ		{ IRQ_TC11MP_KMI1 }
+#define PB11MP_SMC_IRQ		{ }
+#define MPMC_IRQ		{ }
+#define PB11MP_CLCD_IRQ		{ IRQ_PB11MP_CLCD }
+#define DMAC_IRQ		{ IRQ_PB11MP_DMAC }
+#define SCTL_IRQ		{ }
+#define PB11MP_WATCHDOG_IRQ	{ IRQ_PB11MP_WATCHDOG }
+#define PB11MP_GPIO0_IRQ	{ IRQ_PB11MP_GPIO0 }
+#define GPIO1_IRQ		{ IRQ_PB11MP_GPIO1 }
+#define PB11MP_RTC_IRQ		{ IRQ_TC11MP_RTC }
+#define SCI_IRQ			{ IRQ_PB11MP_SCI }
+#define PB11MP_UART0_IRQ	{ IRQ_TC11MP_UART0 }
+#define PB11MP_UART1_IRQ	{ IRQ_TC11MP_UART1 }
+#define PB11MP_UART2_IRQ	{ IRQ_PB11MP_UART2 }
+#define PB11MP_UART3_IRQ	{ IRQ_PB11MP_UART3 }
+#define PB11MP_SSP_IRQ		{ IRQ_PB11MP_SSP }
 
 /* FPGA Primecells */
-AMBA_DEVICE(aaci,	"fpga:aaci",	AACI,		NULL);
-AMBA_DEVICE(mmc0,	"fpga:mmc0",	MMCI0,		&realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0,	"fpga:kmi0",	KMI0,		NULL);
-AMBA_DEVICE(kmi1,	"fpga:kmi1",	KMI1,		NULL);
-AMBA_DEVICE(uart3,	"fpga:uart3",	PB11MP_UART3,	NULL);
+APB_DEVICE(aaci,	"fpga:aaci",	AACI,		NULL);
+APB_DEVICE(mmc0,	"fpga:mmc0",	MMCI0,		&realview_mmc0_plat_data);
+APB_DEVICE(kmi0,	"fpga:kmi0",	KMI0,		NULL);
+APB_DEVICE(kmi1,	"fpga:kmi1",	KMI1,		NULL);
+APB_DEVICE(uart3,	"fpga:uart3",	PB11MP_UART3,	NULL);
 
 /* DevChip Primecells */
-AMBA_DEVICE(smc,	"dev:smc",	PB11MP_SMC,	NULL);
-AMBA_DEVICE(sctl,	"dev:sctl",	SCTL,		NULL);
-AMBA_DEVICE(wdog,	"dev:wdog",	PB11MP_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0,	"dev:gpio0",	PB11MP_GPIO0,	&gpio0_plat_data);
-AMBA_DEVICE(gpio1,	"dev:gpio1",	GPIO1,		&gpio1_plat_data);
-AMBA_DEVICE(gpio2,	"dev:gpio2",	GPIO2,		&gpio2_plat_data);
-AMBA_DEVICE(rtc,	"dev:rtc",	PB11MP_RTC,	NULL);
-AMBA_DEVICE(sci0,	"dev:sci0",	SCI,		NULL);
-AMBA_DEVICE(uart0,	"dev:uart0",	PB11MP_UART0,	NULL);
-AMBA_DEVICE(uart1,	"dev:uart1",	PB11MP_UART1,	NULL);
-AMBA_DEVICE(uart2,	"dev:uart2",	PB11MP_UART2,	NULL);
-AMBA_DEVICE(ssp0,	"dev:ssp0",	PB11MP_SSP,	&ssp0_plat_data);
+AHB_DEVICE(smc,		"dev:smc",	PB11MP_SMC,	NULL);
+AHB_DEVICE(sctl,	"dev:sctl",	SCTL,		NULL);
+APB_DEVICE(wdog,	"dev:wdog",	PB11MP_WATCHDOG, NULL);
+APB_DEVICE(gpio0,	"dev:gpio0",	PB11MP_GPIO0,	&gpio0_plat_data);
+APB_DEVICE(gpio1,	"dev:gpio1",	GPIO1,		&gpio1_plat_data);
+APB_DEVICE(gpio2,	"dev:gpio2",	GPIO2,		&gpio2_plat_data);
+APB_DEVICE(rtc,		"dev:rtc",	PB11MP_RTC,	NULL);
+APB_DEVICE(sci0,	"dev:sci0",	SCI,		NULL);
+APB_DEVICE(uart0,	"dev:uart0",	PB11MP_UART0,	NULL);
+APB_DEVICE(uart1,	"dev:uart1",	PB11MP_UART1,	NULL);
+APB_DEVICE(uart2,	"dev:uart2",	PB11MP_UART2,	NULL);
+APB_DEVICE(ssp0,	"dev:ssp0",	PB11MP_SSP,	&ssp0_plat_data);
 
 /* Primecells on the NEC ISSP chip */
-AMBA_DEVICE(clcd,	"issp:clcd",	PB11MP_CLCD,	&clcd_plat_data);
-AMBA_DEVICE(dmac,	"issp:dmac",	DMAC,		NULL);
+AHB_DEVICE(clcd,	"issp:clcd",	PB11MP_CLCD,	&clcd_plat_data);
+AHB_DEVICE(dmac,	"issp:dmac",	DMAC,		NULL);
 
 static struct amba_device *amba_devs[] __initdata = {
 	&dmac_device,
diff --git a/arch/arm/mach-realview/realview_pba8.c b/arch/arm/mach-realview/realview_pba8.c
index 25b2e59..5965017 100644
--- a/arch/arm/mach-realview/realview_pba8.c
+++ b/arch/arm/mach-realview/realview_pba8.c
@@ -122,52 +122,52 @@
  * RealView PBA8Core AMBA devices
  */
 
-#define GPIO2_IRQ		{ IRQ_PBA8_GPIO2, NO_IRQ }
-#define GPIO3_IRQ		{ IRQ_PBA8_GPIO3, NO_IRQ }
-#define AACI_IRQ		{ IRQ_PBA8_AACI, NO_IRQ }
+#define GPIO2_IRQ		{ IRQ_PBA8_GPIO2 }
+#define GPIO3_IRQ		{ IRQ_PBA8_GPIO3 }
+#define AACI_IRQ		{ IRQ_PBA8_AACI }
 #define MMCI0_IRQ		{ IRQ_PBA8_MMCI0A, IRQ_PBA8_MMCI0B }
-#define KMI0_IRQ		{ IRQ_PBA8_KMI0, NO_IRQ }
-#define KMI1_IRQ		{ IRQ_PBA8_KMI1, NO_IRQ }
-#define PBA8_SMC_IRQ		{ NO_IRQ, NO_IRQ }
-#define MPMC_IRQ		{ NO_IRQ, NO_IRQ }
-#define PBA8_CLCD_IRQ		{ IRQ_PBA8_CLCD, NO_IRQ }
-#define DMAC_IRQ		{ IRQ_PBA8_DMAC, NO_IRQ }
-#define SCTL_IRQ		{ NO_IRQ, NO_IRQ }
-#define PBA8_WATCHDOG_IRQ	{ IRQ_PBA8_WATCHDOG, NO_IRQ }
-#define PBA8_GPIO0_IRQ		{ IRQ_PBA8_GPIO0, NO_IRQ }
-#define GPIO1_IRQ		{ IRQ_PBA8_GPIO1, NO_IRQ }
-#define PBA8_RTC_IRQ		{ IRQ_PBA8_RTC, NO_IRQ }
-#define SCI_IRQ			{ IRQ_PBA8_SCI, NO_IRQ }
-#define PBA8_UART0_IRQ		{ IRQ_PBA8_UART0, NO_IRQ }
-#define PBA8_UART1_IRQ		{ IRQ_PBA8_UART1, NO_IRQ }
-#define PBA8_UART2_IRQ		{ IRQ_PBA8_UART2, NO_IRQ }
-#define PBA8_UART3_IRQ		{ IRQ_PBA8_UART3, NO_IRQ }
-#define PBA8_SSP_IRQ		{ IRQ_PBA8_SSP, NO_IRQ }
+#define KMI0_IRQ		{ IRQ_PBA8_KMI0 }
+#define KMI1_IRQ		{ IRQ_PBA8_KMI1 }
+#define PBA8_SMC_IRQ		{ }
+#define MPMC_IRQ		{ }
+#define PBA8_CLCD_IRQ		{ IRQ_PBA8_CLCD }
+#define DMAC_IRQ		{ IRQ_PBA8_DMAC }
+#define SCTL_IRQ		{ }
+#define PBA8_WATCHDOG_IRQ	{ IRQ_PBA8_WATCHDOG }
+#define PBA8_GPIO0_IRQ		{ IRQ_PBA8_GPIO0 }
+#define GPIO1_IRQ		{ IRQ_PBA8_GPIO1 }
+#define PBA8_RTC_IRQ		{ IRQ_PBA8_RTC }
+#define SCI_IRQ			{ IRQ_PBA8_SCI }
+#define PBA8_UART0_IRQ		{ IRQ_PBA8_UART0 }
+#define PBA8_UART1_IRQ		{ IRQ_PBA8_UART1 }
+#define PBA8_UART2_IRQ		{ IRQ_PBA8_UART2 }
+#define PBA8_UART3_IRQ		{ IRQ_PBA8_UART3 }
+#define PBA8_SSP_IRQ		{ IRQ_PBA8_SSP }
 
 /* FPGA Primecells */
-AMBA_DEVICE(aaci,	"fpga:aaci",	AACI,		NULL);
-AMBA_DEVICE(mmc0,	"fpga:mmc0",	MMCI0,		&realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0,	"fpga:kmi0",	KMI0,		NULL);
-AMBA_DEVICE(kmi1,	"fpga:kmi1",	KMI1,		NULL);
-AMBA_DEVICE(uart3,	"fpga:uart3",	PBA8_UART3,	NULL);
+APB_DEVICE(aaci,	"fpga:aaci",	AACI,		NULL);
+APB_DEVICE(mmc0,	"fpga:mmc0",	MMCI0,		&realview_mmc0_plat_data);
+APB_DEVICE(kmi0,	"fpga:kmi0",	KMI0,		NULL);
+APB_DEVICE(kmi1,	"fpga:kmi1",	KMI1,		NULL);
+APB_DEVICE(uart3,	"fpga:uart3",	PBA8_UART3,	NULL);
 
 /* DevChip Primecells */
-AMBA_DEVICE(smc,	"dev:smc",	PBA8_SMC,	NULL);
-AMBA_DEVICE(sctl,	"dev:sctl",	SCTL,		NULL);
-AMBA_DEVICE(wdog,	"dev:wdog",	PBA8_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0,	"dev:gpio0",	PBA8_GPIO0,	&gpio0_plat_data);
-AMBA_DEVICE(gpio1,	"dev:gpio1",	GPIO1,		&gpio1_plat_data);
-AMBA_DEVICE(gpio2,	"dev:gpio2",	GPIO2,		&gpio2_plat_data);
-AMBA_DEVICE(rtc,	"dev:rtc",	PBA8_RTC,	NULL);
-AMBA_DEVICE(sci0,	"dev:sci0",	SCI,		NULL);
-AMBA_DEVICE(uart0,	"dev:uart0",	PBA8_UART0,	NULL);
-AMBA_DEVICE(uart1,	"dev:uart1",	PBA8_UART1,	NULL);
-AMBA_DEVICE(uart2,	"dev:uart2",	PBA8_UART2,	NULL);
-AMBA_DEVICE(ssp0,	"dev:ssp0",	PBA8_SSP,	&ssp0_plat_data);
+AHB_DEVICE(smc,		"dev:smc",	PBA8_SMC,	NULL);
+AHB_DEVICE(sctl,	"dev:sctl",	SCTL,		NULL);
+APB_DEVICE(wdog,	"dev:wdog",	PBA8_WATCHDOG, NULL);
+APB_DEVICE(gpio0,	"dev:gpio0",	PBA8_GPIO0,	&gpio0_plat_data);
+APB_DEVICE(gpio1,	"dev:gpio1",	GPIO1,		&gpio1_plat_data);
+APB_DEVICE(gpio2,	"dev:gpio2",	GPIO2,		&gpio2_plat_data);
+APB_DEVICE(rtc,		"dev:rtc",	PBA8_RTC,	NULL);
+APB_DEVICE(sci0,	"dev:sci0",	SCI,		NULL);
+APB_DEVICE(uart0,	"dev:uart0",	PBA8_UART0,	NULL);
+APB_DEVICE(uart1,	"dev:uart1",	PBA8_UART1,	NULL);
+APB_DEVICE(uart2,	"dev:uart2",	PBA8_UART2,	NULL);
+APB_DEVICE(ssp0,	"dev:ssp0",	PBA8_SSP,	&ssp0_plat_data);
 
 /* Primecells on the NEC ISSP chip */
-AMBA_DEVICE(clcd,	"issp:clcd",	PBA8_CLCD,	&clcd_plat_data);
-AMBA_DEVICE(dmac,	"issp:dmac",	DMAC,		NULL);
+AHB_DEVICE(clcd,	"issp:clcd",	PBA8_CLCD,	&clcd_plat_data);
+AHB_DEVICE(dmac,	"issp:dmac",	DMAC,		NULL);
 
 static struct amba_device *amba_devs[] __initdata = {
 	&dmac_device,
diff --git a/arch/arm/mach-realview/realview_pbx.c b/arch/arm/mach-realview/realview_pbx.c
index ac71564..1cd9956 100644
--- a/arch/arm/mach-realview/realview_pbx.c
+++ b/arch/arm/mach-realview/realview_pbx.c
@@ -144,52 +144,52 @@
  * RealView PBXCore AMBA devices
  */
 
-#define GPIO2_IRQ		{ IRQ_PBX_GPIO2, NO_IRQ }
-#define GPIO3_IRQ		{ IRQ_PBX_GPIO3, NO_IRQ }
-#define AACI_IRQ		{ IRQ_PBX_AACI, NO_IRQ }
+#define GPIO2_IRQ		{ IRQ_PBX_GPIO2 }
+#define GPIO3_IRQ		{ IRQ_PBX_GPIO3 }
+#define AACI_IRQ		{ IRQ_PBX_AACI }
 #define MMCI0_IRQ		{ IRQ_PBX_MMCI0A, IRQ_PBX_MMCI0B }
-#define KMI0_IRQ		{ IRQ_PBX_KMI0, NO_IRQ }
-#define KMI1_IRQ		{ IRQ_PBX_KMI1, NO_IRQ }
-#define PBX_SMC_IRQ		{ NO_IRQ, NO_IRQ }
-#define MPMC_IRQ		{ NO_IRQ, NO_IRQ }
-#define PBX_CLCD_IRQ		{ IRQ_PBX_CLCD, NO_IRQ }
-#define DMAC_IRQ		{ IRQ_PBX_DMAC, NO_IRQ }
-#define SCTL_IRQ		{ NO_IRQ, NO_IRQ }
-#define PBX_WATCHDOG_IRQ	{ IRQ_PBX_WATCHDOG, NO_IRQ }
-#define PBX_GPIO0_IRQ		{ IRQ_PBX_GPIO0, NO_IRQ }
-#define GPIO1_IRQ		{ IRQ_PBX_GPIO1, NO_IRQ }
-#define PBX_RTC_IRQ		{ IRQ_PBX_RTC, NO_IRQ }
-#define SCI_IRQ			{ IRQ_PBX_SCI, NO_IRQ }
-#define PBX_UART0_IRQ		{ IRQ_PBX_UART0, NO_IRQ }
-#define PBX_UART1_IRQ		{ IRQ_PBX_UART1, NO_IRQ }
-#define PBX_UART2_IRQ		{ IRQ_PBX_UART2, NO_IRQ }
-#define PBX_UART3_IRQ		{ IRQ_PBX_UART3, NO_IRQ }
-#define PBX_SSP_IRQ		{ IRQ_PBX_SSP, NO_IRQ }
+#define KMI0_IRQ		{ IRQ_PBX_KMI0 }
+#define KMI1_IRQ		{ IRQ_PBX_KMI1 }
+#define PBX_SMC_IRQ		{ }
+#define MPMC_IRQ		{ }
+#define PBX_CLCD_IRQ		{ IRQ_PBX_CLCD }
+#define DMAC_IRQ		{ IRQ_PBX_DMAC }
+#define SCTL_IRQ		{ }
+#define PBX_WATCHDOG_IRQ	{ IRQ_PBX_WATCHDOG }
+#define PBX_GPIO0_IRQ		{ IRQ_PBX_GPIO0 }
+#define GPIO1_IRQ		{ IRQ_PBX_GPIO1 }
+#define PBX_RTC_IRQ		{ IRQ_PBX_RTC }
+#define SCI_IRQ			{ IRQ_PBX_SCI }
+#define PBX_UART0_IRQ		{ IRQ_PBX_UART0 }
+#define PBX_UART1_IRQ		{ IRQ_PBX_UART1 }
+#define PBX_UART2_IRQ		{ IRQ_PBX_UART2 }
+#define PBX_UART3_IRQ		{ IRQ_PBX_UART3 }
+#define PBX_SSP_IRQ		{ IRQ_PBX_SSP }
 
 /* FPGA Primecells */
-AMBA_DEVICE(aaci,	"fpga:aaci",	AACI,		NULL);
-AMBA_DEVICE(mmc0,	"fpga:mmc0",	MMCI0,		&realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0,	"fpga:kmi0",	KMI0,		NULL);
-AMBA_DEVICE(kmi1,	"fpga:kmi1",	KMI1,		NULL);
-AMBA_DEVICE(uart3,	"fpga:uart3",	PBX_UART3,	NULL);
+APB_DEVICE(aaci,	"fpga:aaci",	AACI,		NULL);
+APB_DEVICE(mmc0,	"fpga:mmc0",	MMCI0,		&realview_mmc0_plat_data);
+APB_DEVICE(kmi0,	"fpga:kmi0",	KMI0,		NULL);
+APB_DEVICE(kmi1,	"fpga:kmi1",	KMI1,		NULL);
+APB_DEVICE(uart3,	"fpga:uart3",	PBX_UART3,	NULL);
 
 /* DevChip Primecells */
-AMBA_DEVICE(smc,	"dev:smc",	PBX_SMC,	NULL);
-AMBA_DEVICE(sctl,	"dev:sctl",	SCTL,		NULL);
-AMBA_DEVICE(wdog,	"dev:wdog",	PBX_WATCHDOG, 	NULL);
-AMBA_DEVICE(gpio0,	"dev:gpio0",	PBX_GPIO0,	&gpio0_plat_data);
-AMBA_DEVICE(gpio1,	"dev:gpio1",	GPIO1,		&gpio1_plat_data);
-AMBA_DEVICE(gpio2,	"dev:gpio2",	GPIO2,		&gpio2_plat_data);
-AMBA_DEVICE(rtc,	"dev:rtc",	PBX_RTC,	NULL);
-AMBA_DEVICE(sci0,	"dev:sci0",	SCI,		NULL);
-AMBA_DEVICE(uart0,	"dev:uart0",	PBX_UART0,	NULL);
-AMBA_DEVICE(uart1,	"dev:uart1",	PBX_UART1,	NULL);
-AMBA_DEVICE(uart2,	"dev:uart2",	PBX_UART2,	NULL);
-AMBA_DEVICE(ssp0,	"dev:ssp0",	PBX_SSP,	&ssp0_plat_data);
+AHB_DEVICE(smc,	"dev:smc",	PBX_SMC,	NULL);
+AHB_DEVICE(sctl,	"dev:sctl",	SCTL,		NULL);
+APB_DEVICE(wdog,	"dev:wdog",	PBX_WATCHDOG, 	NULL);
+APB_DEVICE(gpio0,	"dev:gpio0",	PBX_GPIO0,	&gpio0_plat_data);
+APB_DEVICE(gpio1,	"dev:gpio1",	GPIO1,		&gpio1_plat_data);
+APB_DEVICE(gpio2,	"dev:gpio2",	GPIO2,		&gpio2_plat_data);
+APB_DEVICE(rtc,		"dev:rtc",	PBX_RTC,	NULL);
+APB_DEVICE(sci0,	"dev:sci0",	SCI,		NULL);
+APB_DEVICE(uart0,	"dev:uart0",	PBX_UART0,	NULL);
+APB_DEVICE(uart1,	"dev:uart1",	PBX_UART1,	NULL);
+APB_DEVICE(uart2,	"dev:uart2",	PBX_UART2,	NULL);
+APB_DEVICE(ssp0,	"dev:ssp0",	PBX_SSP,	&ssp0_plat_data);
 
 /* Primecells on the NEC ISSP chip */
-AMBA_DEVICE(clcd,	"issp:clcd",	PBX_CLCD,	&clcd_plat_data);
-AMBA_DEVICE(dmac,	"issp:dmac",	DMAC,		NULL);
+AHB_DEVICE(clcd,	"issp:clcd",	PBX_CLCD,	&clcd_plat_data);
+AHB_DEVICE(dmac,	"issp:dmac",	DMAC,		NULL);
 
 static struct amba_device *amba_devs[] __initdata = {
 	&dmac_device,
diff --git a/arch/arm/mach-rpc/include/mach/system.h b/arch/arm/mach-rpc/include/mach/system.h
deleted file mode 100644
index 359bab9..0000000
--- a/arch/arm/mach-rpc/include/mach/system.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- *  arch/arm/mach-rpc/include/mach/system.h
- *
- *  Copyright (C) 1996-1999 Russell King.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
diff --git a/arch/arm/mach-s3c2410/include/mach/system.h b/arch/arm/mach-s3c2410/include/mach/system.h
deleted file mode 100644
index 5e215c1..0000000
--- a/arch/arm/mach-s3c2410/include/mach/system.h
+++ /dev/null
@@ -1,54 +0,0 @@
-/* arch/arm/mach-s3c2410/include/mach/system.h
- *
- * Copyright (c) 2003 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410 - System function defines and includes
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/io.h>
-#include <mach/hardware.h>
-
-#include <mach/map.h>
-#include <mach/idle.h>
-
-#include <mach/regs-clock.h>
-
-void (*s3c24xx_idle)(void);
-
-void s3c24xx_default_idle(void)
-{
-	unsigned long tmp;
-	int i;
-
-	/* idle the system by using the idle mode which will wait for an
-	 * interrupt to happen before restarting the system.
-	 */
-
-	/* Warning: going into idle state upsets jtag scanning */
-
-	__raw_writel(__raw_readl(S3C2410_CLKCON) | S3C2410_CLKCON_IDLE,
-		     S3C2410_CLKCON);
-
-	/* the samsung port seems to do a loop and then unset idle.. */
-	for (i = 0; i < 50; i++) {
-		tmp += __raw_readl(S3C2410_CLKCON); /* ensure loop not optimised out */
-	}
-
-	/* this bit is not cleared on re-start... */
-
-	__raw_writel(__raw_readl(S3C2410_CLKCON) & ~S3C2410_CLKCON_IDLE,
-		     S3C2410_CLKCON);
-}
-
-static void arch_idle(void)
-{
-	if (s3c24xx_idle != NULL)
-		(s3c24xx_idle)();
-	else
-		s3c24xx_default_idle();
-}
diff --git a/arch/arm/mach-s3c2412/s3c2412.c b/arch/arm/mach-s3c2412/s3c2412.c
index aff6e85..c6eac98 100644
--- a/arch/arm/mach-s3c2412/s3c2412.c
+++ b/arch/arm/mach-s3c2412/s3c2412.c
@@ -32,8 +32,6 @@
 #include <asm/proc-fns.h>
 #include <asm/irq.h>
 
-#include <mach/idle.h>
-
 #include <plat/cpu-freq.h>
 
 #include <mach/regs-clock.h>
@@ -164,7 +162,7 @@
 
 	/* set our idle function */
 
-	s3c24xx_idle = s3c2412_idle;
+	arm_pm_idle = s3c2412_idle;
 
 	/* register our io-tables */
 
diff --git a/arch/arm/mach-s3c2416/s3c2416.c b/arch/arm/mach-s3c2416/s3c2416.c
index 5287d28..08bb035 100644
--- a/arch/arm/mach-s3c2416/s3c2416.c
+++ b/arch/arm/mach-s3c2416/s3c2416.c
@@ -44,7 +44,6 @@
 #include <asm/proc-fns.h>
 #include <asm/irq.h>
 
-#include <mach/idle.h>
 #include <mach/regs-s3c2443-clock.h>
 
 #include <plat/gpio-core.h>
@@ -88,8 +87,6 @@
 {
 	printk(KERN_INFO "S3C2416: Initializing architecture\n");
 
-	/* s3c24xx_idle = s3c2416_idle;	*/
-
 	/* change WDT IRQ number */
 	s3c_device_wdt.resource[1].start = IRQ_S3C2443_WDT;
 	s3c_device_wdt.resource[1].end   = IRQ_S3C2443_WDT;
diff --git a/arch/arm/mach-s3c64xx/include/mach/system.h b/arch/arm/mach-s3c64xx/include/mach/system.h
deleted file mode 100644
index 353ed43..0000000
--- a/arch/arm/mach-s3c64xx/include/mach/system.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/* linux/arch/arm/mach-s3c6400/include/mach/system.h
- *
- * Copyright 2008 Openmoko, Inc.
- * Copyright 2008 Simtec Electronics
- *      Ben Dooks <ben@simtec.co.uk>
- *      http://armlinux.simtec.co.uk/
- *
- * S3C6400 - system implementation
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H __FILE__
-
-static void arch_idle(void)
-{
-	/* nothing here yet */
-}
-
-#endif /* __ASM_ARCH_IRQ_H */
diff --git a/arch/arm/mach-s5p64x0/common.c b/arch/arm/mach-s5p64x0/common.c
index 52b89a3..9143f8b 100644
--- a/arch/arm/mach-s5p64x0/common.c
+++ b/arch/arm/mach-s5p64x0/common.c
@@ -146,15 +146,12 @@
 {
 	unsigned long val;
 
-	if (!need_resched()) {
-		val = __raw_readl(S5P64X0_PWR_CFG);
-		val &= ~(0x3 << 5);
-		val |= (0x1 << 5);
-		__raw_writel(val, S5P64X0_PWR_CFG);
+	val = __raw_readl(S5P64X0_PWR_CFG);
+	val &= ~(0x3 << 5);
+	val |= (0x1 << 5);
+	__raw_writel(val, S5P64X0_PWR_CFG);
 
-		cpu_do_idle();
-	}
-	local_irq_enable();
+	cpu_do_idle();
 }
 
 /*
@@ -286,7 +283,7 @@
 	printk(KERN_INFO "S5P64X0(S5P6440/S5P6450): Initializing architecture\n");
 
 	/* set idle function */
-	pm_idle = s5p64x0_idle;
+	arm_pm_idle = s5p64x0_idle;
 
 	return device_register(&s5p64x0_dev);
 }
diff --git a/arch/arm/mach-s5p64x0/dma.c b/arch/arm/mach-s5p64x0/dma.c
index f820c07..f7f68ad 100644
--- a/arch/arm/mach-s5p64x0/dma.c
+++ b/arch/arm/mach-s5p64x0/dma.c
@@ -108,34 +108,22 @@
 	.peri_id = s5p6450_pdma_peri,
 };
 
-struct amba_device s5p64x0_device_pdma = {
-	.dev = {
-		.init_name = "dma-pl330",
-		.dma_mask = &dma_dmamask,
-		.coherent_dma_mask = DMA_BIT_MASK(32),
-	},
-	.res = {
-		.start = S5P64X0_PA_PDMA,
-		.end = S5P64X0_PA_PDMA + SZ_4K,
-		.flags = IORESOURCE_MEM,
-	},
-	.irq = {IRQ_DMA0, NO_IRQ},
-	.periphid = 0x00041330,
-};
+AMBA_AHB_DEVICE(s5p64x0_pdma, "dma-pl330", 0x00041330, S5P64X0_PA_PDMA,
+	{IRQ_DMA0}, NULL);
 
 static int __init s5p64x0_dma_init(void)
 {
 	if (soc_is_s5p6450()) {
 		dma_cap_set(DMA_SLAVE, s5p6450_pdma_pdata.cap_mask);
 		dma_cap_set(DMA_CYCLIC, s5p6450_pdma_pdata.cap_mask);
-		s5p64x0_device_pdma.dev.platform_data = &s5p6450_pdma_pdata;
+		s5p64x0_pdma_device.dev.platform_data = &s5p6450_pdma_pdata;
 	} else {
 		dma_cap_set(DMA_SLAVE, s5p6440_pdma_pdata.cap_mask);
 		dma_cap_set(DMA_CYCLIC, s5p6440_pdma_pdata.cap_mask);
-		s5p64x0_device_pdma.dev.platform_data = &s5p6440_pdma_pdata;
+		s5p64x0_pdma_device.dev.platform_data = &s5p6440_pdma_pdata;
 	}
 
-	amba_device_register(&s5p64x0_device_pdma, &iomem_resource);
+	amba_device_register(&s5p64x0_pdma_device, &iomem_resource);
 
 	return 0;
 }
diff --git a/arch/arm/mach-s5p64x0/include/mach/system.h b/arch/arm/mach-s5p64x0/include/mach/system.h
deleted file mode 100644
index cf26e09..0000000
--- a/arch/arm/mach-s5p64x0/include/mach/system.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/* linux/arch/arm/mach-s5p64x0/include/mach/system.h
- *
- * Copyright (c) 2009-2010 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com
- *
- * S5P64X0 - system support header
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H __FILE__
-
-static void arch_idle(void)
-{
-	/* nothing here yet */
-}
-
-#endif /* __ASM_ARCH_SYSTEM_H */
diff --git a/arch/arm/mach-s5pc100/common.c b/arch/arm/mach-s5pc100/common.c
index c909573..ff71e2d 100644
--- a/arch/arm/mach-s5pc100/common.c
+++ b/arch/arm/mach-s5pc100/common.c
@@ -129,14 +129,6 @@
 	}
 };
 
-static void s5pc100_idle(void)
-{
-	if (!need_resched())
-		cpu_do_idle();
-
-	local_irq_enable();
-}
-
 /*
  * s5pc100_map_io
  *
@@ -210,10 +202,6 @@
 int __init s5pc100_init(void)
 {
 	printk(KERN_INFO "S5PC100: Initializing architecture\n");
-
-	/* set idle function */
-	pm_idle = s5pc100_idle;
-
 	return device_register(&s5pc100_dev);
 }
 
diff --git a/arch/arm/mach-s5pc100/dma.c b/arch/arm/mach-s5pc100/dma.c
index c841f4d3..96b1ab3 100644
--- a/arch/arm/mach-s5pc100/dma.c
+++ b/arch/arm/mach-s5pc100/dma.c
@@ -73,21 +73,8 @@
 	.peri_id = pdma0_peri,
 };
 
-struct amba_device s5pc100_device_pdma0 = {
-	.dev = {
-		.init_name = "dma-pl330.0",
-		.dma_mask = &dma_dmamask,
-		.coherent_dma_mask = DMA_BIT_MASK(32),
-		.platform_data = &s5pc100_pdma0_pdata,
-	},
-	.res = {
-		.start = S5PC100_PA_PDMA0,
-		.end = S5PC100_PA_PDMA0 + SZ_4K,
-		.flags = IORESOURCE_MEM,
-	},
-	.irq = {IRQ_PDMA0, NO_IRQ},
-	.periphid = 0x00041330,
-};
+AMBA_AHB_DEVICE(s5pc100_pdma0,  "dma-pl330.0", 0x00041330, S5PC100_PA_PDMA0,
+	{IRQ_PDMA0}, &s5pc100_pdma0_pdata);
 
 u8 pdma1_peri[] = {
 	DMACH_UART0_RX,
@@ -127,31 +114,18 @@
 	.peri_id = pdma1_peri,
 };
 
-struct amba_device s5pc100_device_pdma1 = {
-	.dev = {
-		.init_name = "dma-pl330.1",
-		.dma_mask = &dma_dmamask,
-		.coherent_dma_mask = DMA_BIT_MASK(32),
-		.platform_data = &s5pc100_pdma1_pdata,
-	},
-	.res = {
-		.start = S5PC100_PA_PDMA1,
-		.end = S5PC100_PA_PDMA1 + SZ_4K,
-		.flags = IORESOURCE_MEM,
-	},
-	.irq = {IRQ_PDMA1, NO_IRQ},
-	.periphid = 0x00041330,
-};
+AMBA_AHB_DEVICE(s5pc100_pdma1, "dma-pl330.1", 0x00041330, S5PC100_PA_PDMA1,
+	{IRQ_PDMA1}, &s5pc100_pdma1_pdata);
 
 static int __init s5pc100_dma_init(void)
 {
 	dma_cap_set(DMA_SLAVE, s5pc100_pdma0_pdata.cap_mask);
 	dma_cap_set(DMA_CYCLIC, s5pc100_pdma0_pdata.cap_mask);
-	amba_device_register(&s5pc100_device_pdma0, &iomem_resource);
+	amba_device_register(&s5pc100_pdma0_device, &iomem_resource);
 
 	dma_cap_set(DMA_SLAVE, s5pc100_pdma1_pdata.cap_mask);
 	dma_cap_set(DMA_CYCLIC, s5pc100_pdma1_pdata.cap_mask);
-	amba_device_register(&s5pc100_device_pdma1, &iomem_resource);
+	amba_device_register(&s5pc100_pdma1_device, &iomem_resource);
 
 	return 0;
 }
diff --git a/arch/arm/mach-s5pc100/include/mach/system.h b/arch/arm/mach-s5pc100/include/mach/system.h
deleted file mode 100644
index afc96c2..0000000
--- a/arch/arm/mach-s5pc100/include/mach/system.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/* linux/arch/arm/mach-s5pc100/include/mach/system.h
- *
- * Copyright 2009 Samsung Electronics Co.
- *      Byungho Min <bhmin@samsung.com>
- *
- * S5PC100 - system implementation
- *
- * Based on mach-s3c6400/include/mach/system.h
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H __FILE__
-
-static void arch_idle(void)
-{
-	/* nothing here yet */
-}
-
-#endif /* __ASM_ARCH_IRQ_H */
diff --git a/arch/arm/mach-s5pv210/common.c b/arch/arm/mach-s5pv210/common.c
index 9c1bcdc..4c9e902 100644
--- a/arch/arm/mach-s5pv210/common.c
+++ b/arch/arm/mach-s5pv210/common.c
@@ -142,14 +142,6 @@
 	}
 };
 
-static void s5pv210_idle(void)
-{
-	if (!need_resched())
-		cpu_do_idle();
-
-	local_irq_enable();
-}
-
 void s5pv210_restart(char mode, const char *cmd)
 {
 	__raw_writel(0x1, S5P_SWRESET);
@@ -247,10 +239,6 @@
 int __init s5pv210_init(void)
 {
 	printk(KERN_INFO "S5PV210: Initializing architecture\n");
-
-	/* set idle function */
-	pm_idle = s5pv210_idle;
-
 	return device_register(&s5pv210_dev);
 }
 
diff --git a/arch/arm/mach-s5pv210/dma.c b/arch/arm/mach-s5pv210/dma.c
index a6113e0..f6885d2 100644
--- a/arch/arm/mach-s5pv210/dma.c
+++ b/arch/arm/mach-s5pv210/dma.c
@@ -71,21 +71,8 @@
 	.peri_id = pdma0_peri,
 };
 
-struct amba_device s5pv210_device_pdma0 = {
-	.dev = {
-		.init_name = "dma-pl330.0",
-		.dma_mask = &dma_dmamask,
-		.coherent_dma_mask = DMA_BIT_MASK(32),
-		.platform_data = &s5pv210_pdma0_pdata,
-	},
-	.res = {
-		.start = S5PV210_PA_PDMA0,
-		.end = S5PV210_PA_PDMA0 + SZ_4K,
-		.flags = IORESOURCE_MEM,
-	},
-	.irq = {IRQ_PDMA0, NO_IRQ},
-	.periphid = 0x00041330,
-};
+AMBA_AHB_DEVICE(s5pv210_pdma0, "dma-pl330.0", 0x00041330, S5PV210_PA_PDMA0,
+	{IRQ_PDMA0}, &s5pv210_pdma0_pdata);
 
 u8 pdma1_peri[] = {
 	DMACH_UART0_RX,
@@ -127,31 +114,18 @@
 	.peri_id = pdma1_peri,
 };
 
-struct amba_device s5pv210_device_pdma1 = {
-	.dev = {
-		.init_name = "dma-pl330.1",
-		.dma_mask = &dma_dmamask,
-		.coherent_dma_mask = DMA_BIT_MASK(32),
-		.platform_data = &s5pv210_pdma1_pdata,
-	},
-	.res = {
-		.start = S5PV210_PA_PDMA1,
-		.end = S5PV210_PA_PDMA1 + SZ_4K,
-		.flags = IORESOURCE_MEM,
-	},
-	.irq = {IRQ_PDMA1, NO_IRQ},
-	.periphid = 0x00041330,
-};
+AMBA_AHB_DEVICE(s5pv210_pdma1, "dma-pl330.1", 0x00041330, S5PV210_PA_PDMA1,
+	{IRQ_PDMA1}, &s5pv210_pdma1_pdata);
 
 static int __init s5pv210_dma_init(void)
 {
 	dma_cap_set(DMA_SLAVE, s5pv210_pdma0_pdata.cap_mask);
 	dma_cap_set(DMA_CYCLIC, s5pv210_pdma0_pdata.cap_mask);
-	amba_device_register(&s5pv210_device_pdma0, &iomem_resource);
+	amba_device_register(&s5pv210_pdma0_device, &iomem_resource);
 
 	dma_cap_set(DMA_SLAVE, s5pv210_pdma1_pdata.cap_mask);
 	dma_cap_set(DMA_CYCLIC, s5pv210_pdma1_pdata.cap_mask);
-	amba_device_register(&s5pv210_device_pdma1, &iomem_resource);
+	amba_device_register(&s5pv210_pdma1_device, &iomem_resource);
 
 	return 0;
 }
diff --git a/arch/arm/mach-s5pv210/include/mach/system.h b/arch/arm/mach-s5pv210/include/mach/system.h
deleted file mode 100644
index bf288ce..0000000
--- a/arch/arm/mach-s5pv210/include/mach/system.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/* linux/arch/arm/mach-s5pv210/include/mach/system.h
- *
- * Copyright (c) 2010 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com/
- *
- * S5PV210 - system support header
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H __FILE__
-
-static void arch_idle(void)
-{
-	/* nothing here yet */
-}
-
-#endif /* __ASM_ARCH_SYSTEM_H */
diff --git a/arch/arm/mach-sa1100/include/mach/system.h b/arch/arm/mach-sa1100/include/mach/system.h
deleted file mode 100644
index e17b208..0000000
--- a/arch/arm/mach-sa1100/include/mach/system.h
+++ /dev/null
@@ -1,9 +0,0 @@
-/*
- * arch/arm/mach-sa1100/include/mach/system.h
- *
- * Copyright (c) 1999 Nicolas Pitre <nico@fluxnic.net>
- */
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
diff --git a/arch/arm/mach-shark/core.c b/arch/arm/mach-shark/core.c
index a851c25..6a2a7f2 100644
--- a/arch/arm/mach-shark/core.c
+++ b/arch/arm/mach-shark/core.c
@@ -149,10 +149,16 @@
 	.init		= shark_timer_init,
 };
 
+static void shark_init_early(void)
+{
+	disable_hlt();
+}
+
 MACHINE_START(SHARK, "Shark")
 	/* Maintainer: Alexander Schulz */
 	.atag_offset	= 0x3000,
 	.map_io		= shark_map_io,
+	.init_early	= shark_init_early,
 	.init_irq	= shark_init_irq,
 	.timer		= &shark_timer,
 	.dma_zone_size	= SZ_4M,
diff --git a/arch/arm/mach-shark/include/mach/system.h b/arch/arm/mach-shark/include/mach/system.h
deleted file mode 100644
index 1b2f2c5..0000000
--- a/arch/arm/mach-shark/include/mach/system.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- * arch/arm/mach-shark/include/mach/system.h
- *
- * by Alexander Schulz
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-}
-
-#endif
diff --git a/arch/arm/mach-shmobile/include/mach/system.h b/arch/arm/mach-shmobile/include/mach/system.h
index 956ac18..3bbcb3f 100644
--- a/arch/arm/mach-shmobile/include/mach/system.h
+++ b/arch/arm/mach-shmobile/include/mach/system.h
@@ -1,11 +1,6 @@
 #ifndef __ASM_ARCH_SYSTEM_H
 #define __ASM_ARCH_SYSTEM_H
 
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
-
 static inline void arch_reset(char mode, const char *cmd)
 {
 	soft_restart(0);
diff --git a/arch/arm/mach-spear3xx/include/mach/system.h b/arch/arm/mach-spear3xx/include/mach/system.h
deleted file mode 100644
index 92cee63..0000000
--- a/arch/arm/mach-spear3xx/include/mach/system.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- * arch/arm/mach-spear3xx/include/mach/system.h
- *
- * SPEAr3xx Machine family specific architecture functions
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __MACH_SYSTEM_H
-#define __MACH_SYSTEM_H
-
-#include <plat/system.h>
-
-#endif /* __MACH_SYSTEM_H */
diff --git a/arch/arm/mach-spear3xx/spear300.c b/arch/arm/mach-spear3xx/spear300.c
index a5e46b4..9da50e281 100644
--- a/arch/arm/mach-spear3xx/spear300.c
+++ b/arch/arm/mach-spear3xx/spear300.c
@@ -430,18 +430,8 @@
 	.irq_base	= SPEAR300_GPIO1_INT_BASE,
 };
 
-struct amba_device spear300_gpio1_device = {
-	.dev = {
-		.init_name = "gpio1",
-		.platform_data = &gpio1_plat_data,
-	},
-	.res = {
-		.start = SPEAR300_GPIO_BASE,
-		.end = SPEAR300_GPIO_BASE + SZ_4K - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	.irq = {SPEAR300_VIRQ_GPIO1, NO_IRQ},
-};
+AMBA_APB_DEVICE(spear300_gpio1, "gpio1", 0, SPEAR300_GPIO_BASE,
+	{SPEAR300_VIRQ_GPIO1}, &gpio1_plat_data);
 
 /* spear300 routines */
 void __init spear300_init(struct pmx_mode *pmx_mode, struct pmx_dev **pmx_devs,
diff --git a/arch/arm/mach-spear3xx/spear3xx.c b/arch/arm/mach-spear3xx/spear3xx.c
index 10af45d..b1733c3 100644
--- a/arch/arm/mach-spear3xx/spear3xx.c
+++ b/arch/arm/mach-spear3xx/spear3xx.c
@@ -28,31 +28,12 @@
 	.irq_base	= SPEAR3XX_GPIO_INT_BASE,
 };
 
-struct amba_device spear3xx_gpio_device = {
-	.dev = {
-		.init_name = "gpio",
-		.platform_data = &gpio_plat_data,
-	},
-	.res = {
-		.start = SPEAR3XX_ICM3_GPIO_BASE,
-		.end = SPEAR3XX_ICM3_GPIO_BASE + SZ_4K - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	.irq = {SPEAR3XX_IRQ_BASIC_GPIO, NO_IRQ},
-};
+AMBA_APB_DEVICE(spear3xx_gpio, "gpio", 0, SPEAR3XX_ICM3_GPIO_BASE,
+	{SPEAR3XX_IRQ_BASIC_GPIO}, &gpio_plat_data);
 
 /* uart device registration */
-struct amba_device spear3xx_uart_device = {
-	.dev = {
-		.init_name = "uart",
-	},
-	.res = {
-		.start = SPEAR3XX_ICM1_UART_BASE,
-		.end = SPEAR3XX_ICM1_UART_BASE + SZ_4K - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	.irq = {SPEAR3XX_IRQ_UART, NO_IRQ},
-};
+AMBA_APB_DEVICE(spear3xx_uart, "uart", 0, SPEAR3XX_ICM1_UART_BASE,
+	{SPEAR3XX_IRQ_UART}, NULL);
 
 /* Do spear3xx familiy common initialization part here */
 void __init spear3xx_init(void)
diff --git a/arch/arm/mach-spear6xx/include/mach/system.h b/arch/arm/mach-spear6xx/include/mach/system.h
deleted file mode 100644
index 0b1d2be..0000000
--- a/arch/arm/mach-spear6xx/include/mach/system.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- * arch/arm/mach-spear6xx/include/mach/system.h
- *
- * SPEAr6xx Machine family specific architecture functions
- *
- * Copyright (C) 2009 ST Microelectronics
- * Rajeev Kumar<rajeev-dlh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __MACH_SYSTEM_H
-#define __MACH_SYSTEM_H
-
-#include <plat/system.h>
-
-#endif	/* __MACH_SYSTEM_H */
diff --git a/arch/arm/mach-spear6xx/spear6xx.c b/arch/arm/mach-spear6xx/spear6xx.c
index e0f6628..b997b1b 100644
--- a/arch/arm/mach-spear6xx/spear6xx.c
+++ b/arch/arm/mach-spear6xx/spear6xx.c
@@ -34,7 +34,7 @@
 			.end = SPEAR6XX_ICM1_UART0_BASE + SZ_4K - 1,
 			.flags = IORESOURCE_MEM,
 		},
-		.irq = {IRQ_UART_0, NO_IRQ},
+		.irq = {IRQ_UART_0},
 	}, {
 		.dev = {
 			.init_name = "uart1",
@@ -44,7 +44,7 @@
 			.end = SPEAR6XX_ICM1_UART1_BASE + SZ_4K - 1,
 			.flags = IORESOURCE_MEM,
 		},
-		.irq = {IRQ_UART_1, NO_IRQ},
+		.irq = {IRQ_UART_1},
 	}
 };
 
@@ -73,7 +73,7 @@
 			.end = SPEAR6XX_CPU_GPIO_BASE + SZ_4K - 1,
 			.flags = IORESOURCE_MEM,
 		},
-		.irq = {IRQ_LOCAL_GPIO, NO_IRQ},
+		.irq = {IRQ_LOCAL_GPIO},
 	}, {
 		.dev = {
 			.init_name = "gpio1",
@@ -84,7 +84,7 @@
 			.end = SPEAR6XX_ICM3_GPIO_BASE + SZ_4K - 1,
 			.flags = IORESOURCE_MEM,
 		},
-		.irq = {IRQ_BASIC_GPIO, NO_IRQ},
+		.irq = {IRQ_BASIC_GPIO},
 	}, {
 		.dev = {
 			.init_name = "gpio2",
@@ -95,7 +95,7 @@
 			.end = SPEAR6XX_ICM2_GPIO_BASE + SZ_4K - 1,
 			.flags = IORESOURCE_MEM,
 		},
-		.irq = {IRQ_APPL_GPIO, NO_IRQ},
+		.irq = {IRQ_APPL_GPIO},
 	}
 };
 
diff --git a/arch/arm/mach-tegra/board-dt-tegra20.c b/arch/arm/mach-tegra/board-dt-tegra20.c
index 7a95e0b..e20b419 100644
--- a/arch/arm/mach-tegra/board-dt-tegra20.c
+++ b/arch/arm/mach-tegra/board-dt-tegra20.c
@@ -131,11 +131,7 @@
 }
 
 static const char *tegra20_dt_board_compat[] = {
-	"compulab,trimslice",
-	"nvidia,harmony",
-	"compal,paz00",
-	"nvidia,seaboard",
-	"nvidia,ventana",
+	"nvidia,tegra20",
 	NULL
 };
 
diff --git a/arch/arm/mach-tegra/board-dt-tegra30.c b/arch/arm/mach-tegra/board-dt-tegra30.c
index 3c197e2..6db4df2 100644
--- a/arch/arm/mach-tegra/board-dt-tegra30.c
+++ b/arch/arm/mach-tegra/board-dt-tegra30.c
@@ -47,7 +47,7 @@
 }
 
 static const char *tegra30_dt_board_compat[] = {
-	"nvidia,cardhu",
+	"nvidia,tegra30",
 	NULL
 };
 
diff --git a/arch/arm/mach-tegra/board-harmony-power.c b/arch/arm/mach-tegra/board-harmony-power.c
index 21d1285..c0298b3 100644
--- a/arch/arm/mach-tegra/board-harmony-power.c
+++ b/arch/arm/mach-tegra/board-harmony-power.c
@@ -36,13 +36,14 @@
 
 static struct regulator_init_data ldo0_data = {
 	.constraints = {
-		.min_uV = 1250 * 1000,
+		.min_uV = 3300 * 1000,
 		.max_uV = 3300 * 1000,
 		.valid_modes_mask = (REGULATOR_MODE_NORMAL |
 				     REGULATOR_MODE_STANDBY),
 		.valid_ops_mask = (REGULATOR_CHANGE_MODE |
 				   REGULATOR_CHANGE_STATUS |
 				   REGULATOR_CHANGE_VOLTAGE),
+		.apply_uV = 1,
 	},
 	.num_consumer_supplies = ARRAY_SIZE(tps658621_ldo0_supply),
 	.consumer_supplies = tps658621_ldo0_supply,
diff --git a/arch/arm/mach-tegra/common.c b/arch/arm/mach-tegra/common.c
index a2eb901..2db20da 100644
--- a/arch/arm/mach-tegra/common.c
+++ b/arch/arm/mach-tegra/common.c
@@ -27,7 +27,6 @@
 #include <asm/hardware/gic.h>
 
 #include <mach/iomap.h>
-#include <mach/system.h>
 
 #include "board.h"
 #include "clock.h"
@@ -96,6 +95,8 @@
 #ifdef CONFIG_ARCH_TEGRA_2x_SOC
 void __init tegra20_init_early(void)
 {
+	disable_hlt();  /* idle WFI usage needs to be confirmed */
+
 	tegra_init_fuse();
 	tegra2_init_clocks();
 	tegra_clk_init_from_table(tegra20_clk_init_table);
diff --git a/arch/arm/mach-tegra/include/mach/system.h b/arch/arm/mach-tegra/include/mach/system.h
deleted file mode 100644
index a312988..0000000
--- a/arch/arm/mach-tegra/include/mach/system.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/*
- * arch/arm/mach-tegra/include/mach/system.h
- *
- * Copyright (C) 2010 Google, Inc.
- *
- * Author:
- *	Colin Cross <ccross@google.com>
- *	Erik Gilling <konkers@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef __MACH_TEGRA_SYSTEM_H
-#define __MACH_TEGRA_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-}
-
-#endif
diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c
index b4c6926..b986560 100644
--- a/arch/arm/mach-u300/core.c
+++ b/arch/arm/mach-u300/core.c
@@ -94,19 +94,9 @@
 #endif
 };
 
-static struct amba_device uart0_device = {
-	.dev = {
-		.coherent_dma_mask = ~0,
-		.init_name = "uart0", /* Slow device at 0x3000 offset */
-		.platform_data = &uart0_plat_data,
-	},
-	.res = {
-		.start = U300_UART0_BASE,
-		.end   = U300_UART0_BASE + SZ_4K - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	.irq = { IRQ_U300_UART0, NO_IRQ },
-};
+/* Slow device at 0x3000 offset */
+static AMBA_APB_DEVICE(uart0, "uart0", 0, U300_UART0_BASE,
+	{ IRQ_U300_UART0 }, &uart0_plat_data);
 
 /* The U335 have an additional UART1 on the APP CPU */
 #ifdef CONFIG_MACH_U300_BS335
@@ -118,71 +108,28 @@
 #endif
 };
 
-static struct amba_device uart1_device = {
-	.dev = {
-		.coherent_dma_mask = ~0,
-		.init_name = "uart1", /* Fast device at 0x7000 offset */
-		.platform_data = &uart1_plat_data,
-	},
-	.res = {
-		.start = U300_UART1_BASE,
-		.end   = U300_UART1_BASE + SZ_4K - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	.irq = { IRQ_U300_UART1, NO_IRQ },
-};
+/* Fast device at 0x7000 offset */
+static AMBA_APB_DEVICE(uart1, "uart1", 0, U300_UART1_BASE,
+	{ IRQ_U300_UART1 }, &uart1_plat_data);
 #endif
 
-static struct amba_device pl172_device = {
-	.dev = {
-		.init_name = "pl172", /* AHB device at 0x4000 offset */
-		.platform_data = NULL,
-	},
-	.res = {
-		.start = U300_EMIF_CFG_BASE,
-		.end   = U300_EMIF_CFG_BASE + SZ_4K - 1,
-		.flags = IORESOURCE_MEM,
-	},
-};
+/* AHB device at 0x4000 offset */
+static AMBA_APB_DEVICE(pl172, "pl172", 0, U300_EMIF_CFG_BASE, { }, NULL);
 
 
 /*
  * Everything within this next ifdef deals with external devices connected to
  * the APP SPI bus.
  */
-static struct amba_device pl022_device = {
-	.dev = {
-		.coherent_dma_mask = ~0,
-		.init_name = "pl022", /* Fast device at 0x6000 offset */
-	},
-	.res = {
-		.start = U300_SPI_BASE,
-		.end   = U300_SPI_BASE + SZ_4K - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	.irq = {IRQ_U300_SPI, NO_IRQ },
-	/*
-	 * This device has a DMA channel but the Linux driver does not use
-	 * it currently.
-	 */
-};
+/* Fast device at 0x6000 offset */
+static AMBA_APB_DEVICE(pl022, "pl022", 0, U300_SPI_BASE,
+	{ IRQ_U300_SPI }, NULL);
 
-static struct amba_device mmcsd_device = {
-	.dev = {
-		.init_name = "mmci", /* Fast device at 0x1000 offset */
-		.platform_data = NULL, /* Added later */
-	},
-	.res = {
-		.start = U300_MMCSD_BASE,
-		.end   = U300_MMCSD_BASE + SZ_4K - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	.irq = {IRQ_U300_MMCSD_MCIINTR0, IRQ_U300_MMCSD_MCIINTR1 },
-	/*
-	 * This device has a DMA channel but the Linux driver does not use
-	 * it currently.
-	 */
-};
+/* Fast device at 0x1000 offset */
+#define U300_MMCSD_IRQS	{ IRQ_U300_MMCSD_MCIINTR0, IRQ_U300_MMCSD_MCIINTR1 }
+
+static AMBA_APB_DEVICE(mmcsd, "mmci", 0, U300_MMCSD_BASE,
+	U300_MMCSD_IRQS, NULL);
 
 /*
  * The order of device declaration may be important, since some devices
diff --git a/arch/arm/mach-u300/include/mach/system.h b/arch/arm/mach-u300/include/mach/system.h
deleted file mode 100644
index 574d46e..0000000
--- a/arch/arm/mach-u300/include/mach/system.h
+++ /dev/null
@@ -1,14 +0,0 @@
-/*
- *
- * arch/arm/mach-u300/include/mach/system.h
- *
- *
- * Copyright (C) 2007-2009 ST-Ericsson AB
- * License terms: GNU General Public License (GPL) version 2
- * System shutdown and reset functions.
- * Author: Linus Walleij <linus.walleij@stericsson.com>
- */
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
diff --git a/arch/arm/mach-ux500/devices-common.c b/arch/arm/mach-ux500/devices-common.c
index c563e54..898a645 100644
--- a/arch/arm/mach-ux500/devices-common.c
+++ b/arch/arm/mach-ux500/devices-common.c
@@ -26,29 +26,22 @@
 	struct amba_device *dev;
 	int ret;
 
-	dev = kzalloc(sizeof *dev, GFP_KERNEL);
+	dev = amba_device_alloc(name, base, SZ_4K);
 	if (!dev)
 		return ERR_PTR(-ENOMEM);
 
-	dev->dev.init_name = name;
-
-	dev->res.start = base;
-	dev->res.end = base + SZ_4K - 1;
-	dev->res.flags = IORESOURCE_MEM;
-
 	dev->dma_mask = DMA_BIT_MASK(32);
 	dev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
 
 	dev->irq[0] = irq;
-	dev->irq[1] = NO_IRQ;
 
 	dev->periphid = periphid;
 
 	dev->dev.platform_data = pdata;
 
-	ret = amba_device_register(dev, &iomem_resource);
+	ret = amba_device_add(dev, &iomem_resource);
 	if (ret) {
-		kfree(dev);
+		amba_device_put(dev);
 		return ERR_PTR(ret);
 	}
 
diff --git a/arch/arm/mach-ux500/include/mach/system.h b/arch/arm/mach-ux500/include/mach/system.h
deleted file mode 100644
index 258e5c9..0000000
--- a/arch/arm/mach-ux500/include/mach/system.h
+++ /dev/null
@@ -1,20 +0,0 @@
-/*
- * Copyright (C) 2009 ST-Ericsson.
- *
- * This file is licensed under  the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-	/*
-	 * This should do all the clock switching
-	 * and wait for interrupt tricks
-	 */
-	cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-versatile/core.c b/arch/arm/mach-versatile/core.c
index 02b7b93..4f352e4 100644
--- a/arch/arm/mach-versatile/core.c
+++ b/arch/arm/mach-versatile/core.c
@@ -582,58 +582,58 @@
 	.num_chipselect = 1,
 };
 
-#define AACI_IRQ	{ IRQ_AACI, NO_IRQ }
+#define AACI_IRQ	{ IRQ_AACI }
 #define MMCI0_IRQ	{ IRQ_MMCI0A,IRQ_SIC_MMCI0B }
-#define KMI0_IRQ	{ IRQ_SIC_KMI0, NO_IRQ }
-#define KMI1_IRQ	{ IRQ_SIC_KMI1, NO_IRQ }
+#define KMI0_IRQ	{ IRQ_SIC_KMI0 }
+#define KMI1_IRQ	{ IRQ_SIC_KMI1 }
 
 /*
  * These devices are connected directly to the multi-layer AHB switch
  */
-#define SMC_IRQ		{ NO_IRQ, NO_IRQ }
-#define MPMC_IRQ	{ NO_IRQ, NO_IRQ }
-#define CLCD_IRQ	{ IRQ_CLCDINT, NO_IRQ }
-#define DMAC_IRQ	{ IRQ_DMAINT, NO_IRQ }
+#define SMC_IRQ		{ }
+#define MPMC_IRQ	{ }
+#define CLCD_IRQ	{ IRQ_CLCDINT }
+#define DMAC_IRQ	{ IRQ_DMAINT }
 
 /*
  * These devices are connected via the core APB bridge
  */
-#define SCTL_IRQ	{ NO_IRQ, NO_IRQ }
-#define WATCHDOG_IRQ	{ IRQ_WDOGINT, NO_IRQ }
-#define GPIO0_IRQ	{ IRQ_GPIOINT0, NO_IRQ }
-#define GPIO1_IRQ	{ IRQ_GPIOINT1, NO_IRQ }
-#define RTC_IRQ		{ IRQ_RTCINT, NO_IRQ }
+#define SCTL_IRQ	{ }
+#define WATCHDOG_IRQ	{ IRQ_WDOGINT }
+#define GPIO0_IRQ	{ IRQ_GPIOINT0 }
+#define GPIO1_IRQ	{ IRQ_GPIOINT1 }
+#define RTC_IRQ		{ IRQ_RTCINT }
 
 /*
  * These devices are connected via the DMA APB bridge
  */
-#define SCI_IRQ		{ IRQ_SCIINT, NO_IRQ }
-#define UART0_IRQ	{ IRQ_UARTINT0, NO_IRQ }
-#define UART1_IRQ	{ IRQ_UARTINT1, NO_IRQ }
-#define UART2_IRQ	{ IRQ_UARTINT2, NO_IRQ }
-#define SSP_IRQ		{ IRQ_SSPINT, NO_IRQ }
+#define SCI_IRQ		{ IRQ_SCIINT }
+#define UART0_IRQ	{ IRQ_UARTINT0 }
+#define UART1_IRQ	{ IRQ_UARTINT1 }
+#define UART2_IRQ	{ IRQ_UARTINT2 }
+#define SSP_IRQ		{ IRQ_SSPINT }
 
 /* FPGA Primecells */
-AMBA_DEVICE(aaci,  "fpga:04", AACI,     NULL);
-AMBA_DEVICE(mmc0,  "fpga:05", MMCI0,    &mmc0_plat_data);
-AMBA_DEVICE(kmi0,  "fpga:06", KMI0,     NULL);
-AMBA_DEVICE(kmi1,  "fpga:07", KMI1,     NULL);
+APB_DEVICE(aaci,  "fpga:04", AACI,     NULL);
+APB_DEVICE(mmc0,  "fpga:05", MMCI0,    &mmc0_plat_data);
+APB_DEVICE(kmi0,  "fpga:06", KMI0,     NULL);
+APB_DEVICE(kmi1,  "fpga:07", KMI1,     NULL);
 
 /* DevChip Primecells */
-AMBA_DEVICE(smc,   "dev:00",  SMC,      NULL);
-AMBA_DEVICE(mpmc,  "dev:10",  MPMC,     NULL);
-AMBA_DEVICE(clcd,  "dev:20",  CLCD,     &clcd_plat_data);
-AMBA_DEVICE(dmac,  "dev:30",  DMAC,     NULL);
-AMBA_DEVICE(sctl,  "dev:e0",  SCTL,     NULL);
-AMBA_DEVICE(wdog,  "dev:e1",  WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:e4",  GPIO0,    &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:e5",  GPIO1,    &gpio1_plat_data);
-AMBA_DEVICE(rtc,   "dev:e8",  RTC,      NULL);
-AMBA_DEVICE(sci0,  "dev:f0",  SCI,      NULL);
-AMBA_DEVICE(uart0, "dev:f1",  UART0,    NULL);
-AMBA_DEVICE(uart1, "dev:f2",  UART1,    NULL);
-AMBA_DEVICE(uart2, "dev:f3",  UART2,    NULL);
-AMBA_DEVICE(ssp0,  "dev:f4",  SSP,      &ssp0_plat_data);
+AHB_DEVICE(smc,   "dev:00",  SMC,      NULL);
+AHB_DEVICE(mpmc,  "dev:10",  MPMC,     NULL);
+AHB_DEVICE(clcd,  "dev:20",  CLCD,     &clcd_plat_data);
+AHB_DEVICE(dmac,  "dev:30",  DMAC,     NULL);
+APB_DEVICE(sctl,  "dev:e0",  SCTL,     NULL);
+APB_DEVICE(wdog,  "dev:e1",  WATCHDOG, NULL);
+APB_DEVICE(gpio0, "dev:e4",  GPIO0,    &gpio0_plat_data);
+APB_DEVICE(gpio1, "dev:e5",  GPIO1,    &gpio1_plat_data);
+APB_DEVICE(rtc,   "dev:e8",  RTC,      NULL);
+APB_DEVICE(sci0,  "dev:f0",  SCI,      NULL);
+APB_DEVICE(uart0, "dev:f1",  UART0,    NULL);
+APB_DEVICE(uart1, "dev:f2",  UART1,    NULL);
+APB_DEVICE(uart2, "dev:f3",  UART2,    NULL);
+APB_DEVICE(ssp0,  "dev:f4",  SSP,      &ssp0_plat_data);
 
 static struct amba_device *amba_devs[] __initdata = {
 	&dmac_device,
diff --git a/arch/arm/mach-versatile/core.h b/arch/arm/mach-versatile/core.h
index 2ef2f55..683e607 100644
--- a/arch/arm/mach-versatile/core.h
+++ b/arch/arm/mach-versatile/core.h
@@ -36,20 +36,10 @@
 extern struct of_dev_auxdata versatile_auxdata_lookup[];
 #endif
 
-#define AMBA_DEVICE(name,busid,base,plat)			\
-static struct amba_device name##_device = {			\
-	.dev		= {					\
-		.coherent_dma_mask = ~0,			\
-		.init_name = busid,				\
-		.platform_data = plat,				\
-	},							\
-	.res		= {					\
-		.start	= VERSATILE_##base##_BASE,		\
-		.end	= (VERSATILE_##base##_BASE) + SZ_4K - 1,\
-		.flags	= IORESOURCE_MEM,			\
-	},							\
-	.dma_mask	= ~0,					\
-	.irq		= base##_IRQ,				\
-}
+#define APB_DEVICE(name, busid, base, plat)	\
+static AMBA_APB_DEVICE(name, busid, 0, VERSATILE_##base##_BASE, base##_IRQ, plat)
+
+#define AHB_DEVICE(name, busid, base, plat)	\
+static AMBA_AHB_DEVICE(name, busid, 0, VERSATILE_##base##_BASE, base##_IRQ, plat)
 
 #endif
diff --git a/arch/arm/mach-versatile/include/mach/system.h b/arch/arm/mach-versatile/include/mach/system.h
deleted file mode 100644
index f3fa347..0000000
--- a/arch/arm/mach-versatile/include/mach/system.h
+++ /dev/null
@@ -1,33 +0,0 @@
-/*
- *  arch/arm/mach-versatile/include/mach/system.h
- *
- *  Copyright (C) 2003 ARM Limited
- *  Copyright (C) 2000 Deep Blue Solutions Ltd
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-	/*
-	 * This should do all the clock switching
-	 * and wait for interrupt tricks
-	 */
-	cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-versatile/versatile_pb.c b/arch/arm/mach-versatile/versatile_pb.c
index 9581c19..1973833 100644
--- a/arch/arm/mach-versatile/versatile_pb.c
+++ b/arch/arm/mach-versatile/versatile_pb.c
@@ -58,28 +58,28 @@
 	.irq_base	= IRQ_GPIO3_START,
 };
 
-#define UART3_IRQ	{ IRQ_SIC_UART3, NO_IRQ }
-#define SCI1_IRQ	{ IRQ_SIC_SCI3, NO_IRQ }
+#define UART3_IRQ	{ IRQ_SIC_UART3 }
+#define SCI1_IRQ	{ IRQ_SIC_SCI3 }
 #define MMCI1_IRQ	{ IRQ_MMCI1A, IRQ_SIC_MMCI1B }
 
 /*
  * These devices are connected via the core APB bridge
  */
-#define GPIO2_IRQ	{ IRQ_GPIOINT2, NO_IRQ }
-#define GPIO3_IRQ	{ IRQ_GPIOINT3, NO_IRQ }
+#define GPIO2_IRQ	{ IRQ_GPIOINT2 }
+#define GPIO3_IRQ	{ IRQ_GPIOINT3 }
 
 /*
  * These devices are connected via the DMA APB bridge
  */
 
 /* FPGA Primecells */
-AMBA_DEVICE(uart3, "fpga:09", UART3,    NULL);
-AMBA_DEVICE(sci1,  "fpga:0a", SCI1,     NULL);
-AMBA_DEVICE(mmc1,  "fpga:0b", MMCI1,    &mmc1_plat_data);
+APB_DEVICE(uart3, "fpga:09", UART3,    NULL);
+APB_DEVICE(sci1,  "fpga:0a", SCI1,     NULL);
+APB_DEVICE(mmc1,  "fpga:0b", MMCI1,    &mmc1_plat_data);
 
 /* DevChip Primecells */
-AMBA_DEVICE(gpio2, "dev:e6",  GPIO2,    &gpio2_plat_data);
-AMBA_DEVICE(gpio3, "dev:e7",  GPIO3,    &gpio3_plat_data);
+APB_DEVICE(gpio2, "dev:e6",  GPIO2,    &gpio2_plat_data);
+APB_DEVICE(gpio3, "dev:e7",  GPIO3,    &gpio3_plat_data);
 
 static struct amba_device *amba_devs[] __initdata = {
 	&uart3_device,
diff --git a/arch/arm/mach-vexpress/core.h b/arch/arm/mach-vexpress/core.h
index f439715..9f0f282 100644
--- a/arch/arm/mach-vexpress/core.h
+++ b/arch/arm/mach-vexpress/core.h
@@ -1,19 +1,2 @@
 #define __MMIO_P2V(x)	(((x) & 0xfffff) | (((x) & 0x0f000000) >> 4) | 0xf8000000)
 #define MMIO_P2V(x)	((void __iomem *)__MMIO_P2V(x))
-
-#define AMBA_DEVICE(name,busid,base,plat)	\
-struct amba_device name##_device = {		\
-	.dev		= {			\
-		.coherent_dma_mask = ~0UL,	\
-		.init_name = busid,		\
-		.platform_data = plat,		\
-	},					\
-	.res		= {			\
-		.start	= base,			\
-		.end	= base + SZ_4K - 1,	\
-		.flags	= IORESOURCE_MEM,	\
-	},					\
-	.dma_mask	= ~0UL,			\
-	.irq		= IRQ_##base,		\
-	/* .dma		= DMA_##base,*/		\
-}
diff --git a/arch/arm/mach-vexpress/ct-ca9x4.c b/arch/arm/mach-vexpress/ct-ca9x4.c
index b1e87c1..1b1d2e4 100644
--- a/arch/arm/mach-vexpress/ct-ca9x4.c
+++ b/arch/arm/mach-vexpress/ct-ca9x4.c
@@ -109,10 +109,10 @@
 	.remove		= versatile_clcd_remove_dma,
 };
 
-static AMBA_DEVICE(clcd, "ct:clcd", CT_CA9X4_CLCDC, &ct_ca9x4_clcd_data);
-static AMBA_DEVICE(dmc, "ct:dmc", CT_CA9X4_DMC, NULL);
-static AMBA_DEVICE(smc, "ct:smc", CT_CA9X4_SMC, NULL);
-static AMBA_DEVICE(gpio, "ct:gpio", CT_CA9X4_GPIO, NULL);
+static AMBA_AHB_DEVICE(clcd, "ct:clcd", 0, CT_CA9X4_CLCDC, IRQ_CT_CA9X4_CLCDC, &ct_ca9x4_clcd_data);
+static AMBA_APB_DEVICE(dmc, "ct:dmc", 0, CT_CA9X4_DMC, IRQ_CT_CA9X4_DMC, NULL);
+static AMBA_APB_DEVICE(smc, "ct:smc", 0, CT_CA9X4_SMC, IRQ_CT_CA9X4_SMC, NULL);
+static AMBA_APB_DEVICE(gpio, "ct:gpio", 0, CT_CA9X4_GPIO, IRQ_CT_CA9X4_GPIO, NULL);
 
 static struct amba_device *ct_ca9x4_amba_devs[] __initdata = {
 	&clcd_device,
diff --git a/arch/arm/mach-vexpress/include/mach/ct-ca9x4.h b/arch/arm/mach-vexpress/include/mach/ct-ca9x4.h
index a34d3d4..a40468f 100644
--- a/arch/arm/mach-vexpress/include/mach/ct-ca9x4.h
+++ b/arch/arm/mach-vexpress/include/mach/ct-ca9x4.h
@@ -35,7 +35,7 @@
  * Interrupts.  Those in {} are for AMBA devices
  */
 #define IRQ_CT_CA9X4_CLCDC	{ 76 }
-#define IRQ_CT_CA9X4_DMC	{ -1 }
+#define IRQ_CT_CA9X4_DMC	{ 0 }
 #define IRQ_CT_CA9X4_SMC	{ 77, 78 }
 #define IRQ_CT_CA9X4_TIMER0	80
 #define IRQ_CT_CA9X4_TIMER1	81
diff --git a/arch/arm/mach-vexpress/include/mach/system.h b/arch/arm/mach-vexpress/include/mach/system.h
deleted file mode 100644
index f653a8e..0000000
--- a/arch/arm/mach-vexpress/include/mach/system.h
+++ /dev/null
@@ -1,33 +0,0 @@
-/*
- *  arch/arm/mach-vexpress/include/mach/system.h
- *
- *  Copyright (C) 2003 ARM Limited
- *  Copyright (C) 2000 Deep Blue Solutions Ltd
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-	/*
-	 * This should do all the clock switching
-	 * and wait for interrupt tricks
-	 */
-	cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-vexpress/v2m.c b/arch/arm/mach-vexpress/v2m.c
index b4a28ca..ad64f97 100644
--- a/arch/arm/mach-vexpress/v2m.c
+++ b/arch/arm/mach-vexpress/v2m.c
@@ -266,16 +266,16 @@
 	.status		= v2m_mmci_status,
 };
 
-static AMBA_DEVICE(aaci,  "mb:aaci",  V2M_AACI, NULL);
-static AMBA_DEVICE(mmci,  "mb:mmci",  V2M_MMCI, &v2m_mmci_data);
-static AMBA_DEVICE(kmi0,  "mb:kmi0",  V2M_KMI0, NULL);
-static AMBA_DEVICE(kmi1,  "mb:kmi1",  V2M_KMI1, NULL);
-static AMBA_DEVICE(uart0, "mb:uart0", V2M_UART0, NULL);
-static AMBA_DEVICE(uart1, "mb:uart1", V2M_UART1, NULL);
-static AMBA_DEVICE(uart2, "mb:uart2", V2M_UART2, NULL);
-static AMBA_DEVICE(uart3, "mb:uart3", V2M_UART3, NULL);
-static AMBA_DEVICE(wdt,   "mb:wdt",   V2M_WDT, NULL);
-static AMBA_DEVICE(rtc,   "mb:rtc",   V2M_RTC, NULL);
+static AMBA_APB_DEVICE(aaci,  "mb:aaci",  0, V2M_AACI, IRQ_V2M_AACI, NULL);
+static AMBA_APB_DEVICE(mmci,  "mb:mmci",  0, V2M_MMCI, IRQ_V2M_MMCI, &v2m_mmci_data);
+static AMBA_APB_DEVICE(kmi0,  "mb:kmi0",  0, V2M_KMI0, IRQ_V2M_KMI0, NULL);
+static AMBA_APB_DEVICE(kmi1,  "mb:kmi1",  0, V2M_KMI1, IRQ_V2M_KMI1, NULL);
+static AMBA_APB_DEVICE(uart0, "mb:uart0", 0, V2M_UART0, IRQ_V2M_UART0, NULL);
+static AMBA_APB_DEVICE(uart1, "mb:uart1", 0, V2M_UART1, IRQ_V2M_UART1, NULL);
+static AMBA_APB_DEVICE(uart2, "mb:uart2", 0, V2M_UART2, IRQ_V2M_UART2, NULL);
+static AMBA_APB_DEVICE(uart3, "mb:uart3", 0, V2M_UART3, IRQ_V2M_UART3, NULL);
+static AMBA_APB_DEVICE(wdt,   "mb:wdt",   0, V2M_WDT, IRQ_V2M_WDT, NULL);
+static AMBA_APB_DEVICE(rtc,   "mb:rtc",   0, V2M_RTC, IRQ_V2M_RTC, NULL);
 
 static struct amba_device *v2m_amba_devs[] __initdata = {
 	&aaci_device,
diff --git a/arch/arm/mach-vt8500/include/mach/system.h b/arch/arm/mach-vt8500/include/mach/system.h
index d6c757e..58fa801 100644
--- a/arch/arm/mach-vt8500/include/mach/system.h
+++ b/arch/arm/mach-vt8500/include/mach/system.h
@@ -7,11 +7,6 @@
 /* PM Software Reset request register */
 #define VT8500_PMSR_VIRT	0xf8130060
 
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
-
 static inline void arch_reset(char mode, const char *cmd)
 {
 	writel(1, VT8500_PMSR_VIRT);
diff --git a/arch/arm/mach-w90x900/dev.c b/arch/arm/mach-w90x900/dev.c
index 78110be..db82568 100644
--- a/arch/arm/mach-w90x900/dev.c
+++ b/arch/arm/mach-w90x900/dev.c
@@ -530,6 +530,7 @@
 
 void __init nuc900_board_init(struct platform_device **device, int size)
 {
+	disable_hlt();
 	platform_add_devices(device, size);
 	platform_add_devices(nuc900_public_dev, ARRAY_SIZE(nuc900_public_dev));
 	spi_register_board_info(nuc900_spi_board_info,
diff --git a/arch/arm/mach-w90x900/include/mach/system.h b/arch/arm/mach-w90x900/include/mach/system.h
deleted file mode 100644
index 2aaeb93..0000000
--- a/arch/arm/mach-w90x900/include/mach/system.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- * arch/arm/mach-w90x900/include/mach/system.h
- *
- * Copyright (c) 2008 Nuvoton technology corporation
- * All rights reserved.
- *
- * Wan ZongShun <mcuos.com@gmail.com>
- *
- * Based on arch/arm/mach-s3c2410/include/mach/system.h
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-static void arch_idle(void)
-{
-}
diff --git a/arch/arm/mach-zynq/include/mach/system.h b/arch/arm/mach-zynq/include/mach/system.h
deleted file mode 100644
index 8e88e0b..0000000
--- a/arch/arm/mach-zynq/include/mach/system.h
+++ /dev/null
@@ -1,23 +0,0 @@
-/* arch/arm/mach-zynq/include/mach/system.h
- *
- *  Copyright (C) 2011 Xilinx
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __MACH_SYSTEM_H__
-#define __MACH_SYSTEM_H__
-
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/plat-mxc/include/mach/system.h b/arch/arm/plat-mxc/include/mach/system.h
deleted file mode 100644
index 13ad0df..0000000
--- a/arch/arm/plat-mxc/include/mach/system.h
+++ /dev/null
@@ -1,25 +0,0 @@
-/*
- *  Copyright (C) 1999 ARM Limited
- *  Copyright (C) 2000 Deep Blue Solutions Ltd
- *  Copyright 2004-2008 Freescale Semiconductor, Inc. All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ASM_ARCH_MXC_SYSTEM_H__
-#define __ASM_ARCH_MXC_SYSTEM_H__
-
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
-
-#endif /* __ASM_ARCH_MXC_SYSTEM_H__ */
diff --git a/arch/arm/plat-omap/include/plat/board-ams-delta.h b/arch/arm/plat-omap/include/plat/board-ams-delta.h
index 51b102d..ad6f865 100644
--- a/arch/arm/plat-omap/include/plat/board-ams-delta.h
+++ b/arch/arm/plat-omap/include/plat/board-ams-delta.h
@@ -28,33 +28,8 @@
 
 #if defined (CONFIG_MACH_AMS_DELTA)
 
-#define AMS_DELTA_LATCH1_PHYS		0x01000000
-#define AMS_DELTA_LATCH1_VIRT		0xEA000000
-#define AMS_DELTA_MODEM_PHYS		0x04000000
-#define AMS_DELTA_MODEM_VIRT		0xEB000000
-#define AMS_DELTA_LATCH2_PHYS		0x08000000
-#define AMS_DELTA_LATCH2_VIRT		0xEC000000
-
-#define AMS_DELTA_LATCH1_LED_CAMERA	0x01
-#define AMS_DELTA_LATCH1_LED_ADVERT	0x02
-#define AMS_DELTA_LATCH1_LED_EMAIL	0x04
-#define AMS_DELTA_LATCH1_LED_HANDSFREE	0x08
-#define AMS_DELTA_LATCH1_LED_VOICEMAIL	0x10
-#define AMS_DELTA_LATCH1_LED_VOICE	0x20
-
-#define AMS_DELTA_LATCH2_LCD_VBLEN	0x0001
-#define AMS_DELTA_LATCH2_LCD_NDISP	0x0002
-#define AMS_DELTA_LATCH2_NAND_NCE	0x0004
-#define AMS_DELTA_LATCH2_NAND_NRE	0x0008
-#define AMS_DELTA_LATCH2_NAND_NWP	0x0010
-#define AMS_DELTA_LATCH2_NAND_NWE	0x0020
-#define AMS_DELTA_LATCH2_NAND_ALE	0x0040
-#define AMS_DELTA_LATCH2_NAND_CLE	0x0080
-#define AMD_DELTA_LATCH2_KEYBRD_PWR	0x0100
-#define AMD_DELTA_LATCH2_KEYBRD_DATA	0x0200
 #define AMD_DELTA_LATCH2_SCARD_RSTIN	0x0400
 #define AMD_DELTA_LATCH2_SCARD_CMDVCC	0x0800
-#define AMS_DELTA_LATCH2_MODEM_NRESET	0x1000
 #define AMS_DELTA_LATCH2_MODEM_CODEC	0x2000
 
 #define AMS_DELTA_GPIO_PIN_KEYBRD_DATA	0
@@ -66,9 +41,29 @@
 #define AMS_DELTA_GPIO_PIN_CONFIG	11
 #define AMS_DELTA_GPIO_PIN_NAND_RB	12
 
+#define AMS_DELTA_GPIO_PIN_LCD_VBLEN		240
+#define AMS_DELTA_GPIO_PIN_LCD_NDISP		241
+#define AMS_DELTA_GPIO_PIN_NAND_NCE		242
+#define AMS_DELTA_GPIO_PIN_NAND_NRE		243
+#define AMS_DELTA_GPIO_PIN_NAND_NWP		244
+#define AMS_DELTA_GPIO_PIN_NAND_NWE		245
+#define AMS_DELTA_GPIO_PIN_NAND_ALE		246
+#define AMS_DELTA_GPIO_PIN_NAND_CLE		247
+#define AMS_DELTA_GPIO_PIN_KEYBRD_PWR		248
+#define AMS_DELTA_GPIO_PIN_KEYBRD_DATAOUT	249
+#define AMS_DELTA_GPIO_PIN_SCARD_RSTIN		250
+#define AMS_DELTA_GPIO_PIN_SCARD_CMDVCC		251
+#define AMS_DELTA_GPIO_PIN_MODEM_NRESET		252
+#define AMS_DELTA_GPIO_PIN_MODEM_CODEC		253
+
+#define AMS_DELTA_LATCH2_GPIO_BASE	AMS_DELTA_GPIO_PIN_LCD_VBLEN
+#define AMS_DELTA_LATCH2_NGPIO		16
+
 #ifndef __ASSEMBLY__
-void ams_delta_latch1_write(u8 mask, u8 value);
-void ams_delta_latch2_write(u16 mask, u16 value);
+void ams_delta_latch_write(int base, int ngpio, u16 mask, u16 value);
+#define ams_delta_latch2_write(mask, value) \
+	ams_delta_latch_write(AMS_DELTA_LATCH2_GPIO_BASE, \
+			AMS_DELTA_LATCH2_NGPIO, (mask), (value))
 #endif
 
 #endif /* CONFIG_MACH_AMS_DELTA */
diff --git a/arch/arm/plat-omap/include/plat/system.h b/arch/arm/plat-omap/include/plat/system.h
deleted file mode 100644
index 8e5ebd7..0000000
--- a/arch/arm/plat-omap/include/plat/system.h
+++ /dev/null
@@ -1,15 +0,0 @@
-/*
- * Copied from arch/arm/mach-sa1100/include/mach/system.h
- * Copyright (c) 1999 Nicolas Pitre <nico@fluxnic.net>
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-#include <asm/proc-fns.h>
-
-static inline void arch_idle(void)
-{
-	cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/plat-s3c24xx/cpu.c b/arch/arm/plat-s3c24xx/cpu.c
index 21f1fda..32a0993 100644
--- a/arch/arm/plat-s3c24xx/cpu.c
+++ b/arch/arm/plat-s3c24xx/cpu.c
@@ -32,6 +32,7 @@
 #include <linux/io.h>
 
 #include <mach/hardware.h>
+#include <mach/regs-clock.h>
 #include <asm/irq.h>
 #include <asm/cacheflush.h>
 
@@ -190,8 +191,34 @@
 	return __raw_readl(S3C2410_GSTATUS1);
 }
 
+static void s3c24xx_default_idle(void)
+{
+	unsigned long tmp;
+	int i;
+
+	/* idle the system by using the idle mode which will wait for an
+	 * interrupt to happen before restarting the system.
+	 */
+
+	/* Warning: going into idle state upsets jtag scanning */
+
+	__raw_writel(__raw_readl(S3C2410_CLKCON) | S3C2410_CLKCON_IDLE,
+		     S3C2410_CLKCON);
+
+	/* the samsung port seems to do a loop and then unset idle.. */
+	for (i = 0; i < 50; i++)
+		tmp += __raw_readl(S3C2410_CLKCON); /* ensure loop not optimised out */
+
+	/* this bit is not cleared on re-start... */
+
+	__raw_writel(__raw_readl(S3C2410_CLKCON) & ~S3C2410_CLKCON_IDLE,
+		     S3C2410_CLKCON);
+}
+
 void __init s3c24xx_init_io(struct map_desc *mach_desc, int size)
 {
+	arm_pm_idle = s3c24xx_default_idle;
+
 	/* initialise the io descriptors we need for initialisation */
 	iotable_init(mach_desc, size);
 	iotable_init(s3c_iodesc, ARRAY_SIZE(s3c_iodesc));
diff --git a/arch/arm/plat-spear/include/plat/system.h b/arch/arm/plat-spear/include/plat/system.h
deleted file mode 100644
index 86c6f83..0000000
--- a/arch/arm/plat-spear/include/plat/system.h
+++ /dev/null
@@ -1,26 +0,0 @@
-/*
- * arch/arm/plat-spear/include/plat/system.h
- *
- * SPEAr platform specific architecture functions
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __PLAT_SYSTEM_H
-#define __PLAT_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-	/*
-	 * This should do all the clock switching
-	 * and wait for interrupt tricks
-	 */
-	cpu_do_idle();
-}
-
-#endif /* __PLAT_SYSTEM_H */
diff --git a/drivers/amba/bus.c b/drivers/amba/bus.c
index 54eaf96..01c2cf4 100644
--- a/drivers/amba/bus.c
+++ b/drivers/amba/bus.c
@@ -497,37 +497,22 @@
 }
 
 /**
- *	amba_device_register - register an AMBA device
- *	@dev: AMBA device to register
- *	@parent: parent memory resource
+ *	amba_device_add - add a previously allocated AMBA device structure
+ *	@dev: AMBA device allocated by amba_device_alloc
+ *	@parent: resource parent for this devices resources
  *
- *	Setup the AMBA device, reading the cell ID if present.
- *	Claim the resource, and register the AMBA device with
- *	the Linux device manager.
+ *	Claim the resource, and read the device cell ID if not already
+ *	initialized.  Register the AMBA device with the Linux device
+ *	manager.
  */
-int amba_device_register(struct amba_device *dev, struct resource *parent)
+int amba_device_add(struct amba_device *dev, struct resource *parent)
 {
 	u32 size;
 	void __iomem *tmp;
 	int i, ret;
 
-	device_initialize(&dev->dev);
-
-	/*
-	 * Copy from device_add
-	 */
-	if (dev->dev.init_name) {
-		dev_set_name(&dev->dev, "%s", dev->dev.init_name);
-		dev->dev.init_name = NULL;
-	}
-
-	dev->dev.release = amba_device_release;
-	dev->dev.bus = &amba_bustype;
-	dev->dev.dma_mask = &dev->dma_mask;
-	dev->res.name = dev_name(&dev->dev);
-
-	if (!dev->dev.coherent_dma_mask && dev->dma_mask)
-		dev_warn(&dev->dev, "coherent dma mask is unset\n");
+	WARN_ON(dev->irq[0] == (unsigned int)-1);
+	WARN_ON(dev->irq[1] == (unsigned int)-1);
 
 	ret = request_resource(parent, &dev->res);
 	if (ret)
@@ -582,9 +567,9 @@
 	if (ret)
 		goto err_release;
 
-	if (dev->irq[0] != NO_IRQ)
+	if (dev->irq[0] && dev->irq[0] != NO_IRQ)
 		ret = device_create_file(&dev->dev, &dev_attr_irq0);
-	if (ret == 0 && dev->irq[1] != NO_IRQ)
+	if (ret == 0 && dev->irq[1] && dev->irq[1] != NO_IRQ)
 		ret = device_create_file(&dev->dev, &dev_attr_irq1);
 	if (ret == 0)
 		return ret;
@@ -596,6 +581,74 @@
  err_out:
 	return ret;
 }
+EXPORT_SYMBOL_GPL(amba_device_add);
+
+static void amba_device_initialize(struct amba_device *dev, const char *name)
+{
+	device_initialize(&dev->dev);
+	if (name)
+		dev_set_name(&dev->dev, "%s", name);
+	dev->dev.release = amba_device_release;
+	dev->dev.bus = &amba_bustype;
+	dev->dev.dma_mask = &dev->dma_mask;
+	dev->res.name = dev_name(&dev->dev);
+}
+
+/**
+ *	amba_device_alloc - allocate an AMBA device
+ *	@name: sysfs name of the AMBA device
+ *	@base: base of AMBA device
+ *	@size: size of AMBA device
+ *
+ *	Allocate and initialize an AMBA device structure.  Returns %NULL
+ *	on failure.
+ */
+struct amba_device *amba_device_alloc(const char *name, resource_size_t base,
+	size_t size)
+{
+	struct amba_device *dev;
+
+	dev = kzalloc(sizeof(*dev), GFP_KERNEL);
+	if (dev) {
+		amba_device_initialize(dev, name);
+		dev->res.start = base;
+		dev->res.end = base + size - 1;
+		dev->res.flags = IORESOURCE_MEM;
+	}
+
+	return dev;
+}
+EXPORT_SYMBOL_GPL(amba_device_alloc);
+
+/**
+ *	amba_device_register - register an AMBA device
+ *	@dev: AMBA device to register
+ *	@parent: parent memory resource
+ *
+ *	Setup the AMBA device, reading the cell ID if present.
+ *	Claim the resource, and register the AMBA device with
+ *	the Linux device manager.
+ */
+int amba_device_register(struct amba_device *dev, struct resource *parent)
+{
+	amba_device_initialize(dev, dev->dev.init_name);
+	dev->dev.init_name = NULL;
+
+	if (!dev->dev.coherent_dma_mask && dev->dma_mask)
+		dev_warn(&dev->dev, "coherent dma mask is unset\n");
+
+	return amba_device_add(dev, parent);
+}
+
+/**
+ *	amba_device_put - put an AMBA device
+ *	@dev: AMBA device to put
+ */
+void amba_device_put(struct amba_device *dev)
+{
+	put_device(&dev->dev);
+}
+EXPORT_SYMBOL_GPL(amba_device_put);
 
 /**
  *	amba_device_unregister - unregister an AMBA device
diff --git a/drivers/input/serio/ams_delta_serio.c b/drivers/input/serio/ams_delta_serio.c
index d4d08bd..bd5b10e 100644
--- a/drivers/input/serio/ams_delta_serio.c
+++ b/drivers/input/serio/ams_delta_serio.c
@@ -92,8 +92,7 @@
 static int ams_delta_serio_open(struct serio *serio)
 {
 	/* enable keyboard */
-	ams_delta_latch2_write(AMD_DELTA_LATCH2_KEYBRD_PWR,
-			AMD_DELTA_LATCH2_KEYBRD_PWR);
+	gpio_set_value(AMS_DELTA_GPIO_PIN_KEYBRD_PWR, 1);
 
 	return 0;
 }
@@ -101,9 +100,32 @@
 static void ams_delta_serio_close(struct serio *serio)
 {
 	/* disable keyboard */
-	ams_delta_latch2_write(AMD_DELTA_LATCH2_KEYBRD_PWR, 0);
+	gpio_set_value(AMS_DELTA_GPIO_PIN_KEYBRD_PWR, 0);
 }
 
+static const struct gpio ams_delta_gpios[] __initconst_or_module = {
+	{
+		.gpio	= AMS_DELTA_GPIO_PIN_KEYBRD_DATA,
+		.flags	= GPIOF_DIR_IN,
+		.label	= "serio-data",
+	},
+	{
+		.gpio	= AMS_DELTA_GPIO_PIN_KEYBRD_CLK,
+		.flags	= GPIOF_DIR_IN,
+		.label	= "serio-clock",
+	},
+	{
+		.gpio	= AMS_DELTA_GPIO_PIN_KEYBRD_PWR,
+		.flags	= GPIOF_OUT_INIT_LOW,
+		.label	= "serio-power",
+	},
+	{
+		.gpio	= AMS_DELTA_GPIO_PIN_KEYBRD_DATAOUT,
+		.flags	= GPIOF_OUT_INIT_LOW,
+		.label	= "serio-dataout",
+	},
+};
+
 static int __init ams_delta_serio_init(void)
 {
 	int err;
@@ -123,19 +145,12 @@
 	strlcpy(ams_delta_serio->phys, "GPIO/serio0",
 			sizeof(ams_delta_serio->phys));
 
-	err = gpio_request(AMS_DELTA_GPIO_PIN_KEYBRD_DATA, "serio-data");
+	err = gpio_request_array(ams_delta_gpios,
+				ARRAY_SIZE(ams_delta_gpios));
 	if (err) {
-		pr_err("ams_delta_serio: Couldn't request gpio pin for data\n");
+		pr_err("ams_delta_serio: Couldn't request gpio pins\n");
 		goto serio;
 	}
-	gpio_direction_input(AMS_DELTA_GPIO_PIN_KEYBRD_DATA);
-
-	err = gpio_request(AMS_DELTA_GPIO_PIN_KEYBRD_CLK, "serio-clock");
-	if (err) {
-		pr_err("ams_delta_serio: couldn't request gpio pin for clock\n");
-		goto gpio_data;
-	}
-	gpio_direction_input(AMS_DELTA_GPIO_PIN_KEYBRD_CLK);
 
 	err = request_irq(gpio_to_irq(AMS_DELTA_GPIO_PIN_KEYBRD_CLK),
 			ams_delta_serio_interrupt, IRQ_TYPE_EDGE_RISING,
@@ -143,7 +158,7 @@
 	if (err < 0) {
 		pr_err("ams_delta_serio: couldn't request gpio interrupt %d\n",
 				gpio_to_irq(AMS_DELTA_GPIO_PIN_KEYBRD_CLK));
-		goto gpio_clk;
+		goto gpio;
 	}
 	/*
 	 * Since GPIO register handling for keyboard clock pin is performed
@@ -157,10 +172,9 @@
 	dev_info(&ams_delta_serio->dev, "%s\n", ams_delta_serio->name);
 
 	return 0;
-gpio_clk:
-	gpio_free(AMS_DELTA_GPIO_PIN_KEYBRD_CLK);
-gpio_data:
-	gpio_free(AMS_DELTA_GPIO_PIN_KEYBRD_DATA);
+gpio:
+	gpio_free_array(ams_delta_gpios,
+			ARRAY_SIZE(ams_delta_gpios));
 serio:
 	kfree(ams_delta_serio);
 	return err;
@@ -171,7 +185,7 @@
 {
 	serio_unregister_port(ams_delta_serio);
 	free_irq(OMAP_GPIO_IRQ(AMS_DELTA_GPIO_PIN_KEYBRD_CLK), 0);
-	gpio_free(AMS_DELTA_GPIO_PIN_KEYBRD_CLK);
-	gpio_free(AMS_DELTA_GPIO_PIN_KEYBRD_DATA);
+	gpio_free_array(ams_delta_gpios,
+			ARRAY_SIZE(ams_delta_gpios));
 }
 module_exit(ams_delta_serio_exit);
diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index 9ca28fc..f5d5c03 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -74,13 +74,6 @@
 	  This option enables support for LEDs connected to GPIO lines
 	  on Samsung S3C24XX series CPUs, such as the S3C2410 and S3C2440.
 
-config LEDS_AMS_DELTA
-	tristate "LED Support for the Amstrad Delta (E3)"
-	depends on LEDS_CLASS
-	depends on MACH_AMS_DELTA
-	help
-	  This option enables support for the LEDs on Amstrad Delta (E3).
-
 config LEDS_NET48XX
 	tristate "LED Support for Soekris net48xx series Error LED"
 	depends on LEDS_CLASS
diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
index 1fc6875..8cab1bb 100644
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -12,7 +12,6 @@
 obj-$(CONFIG_LEDS_LM3530)		+= leds-lm3530.o
 obj-$(CONFIG_LEDS_MIKROTIK_RB532)	+= leds-rb532.o
 obj-$(CONFIG_LEDS_S3C24XX)		+= leds-s3c24xx.o
-obj-$(CONFIG_LEDS_AMS_DELTA)		+= leds-ams-delta.o
 obj-$(CONFIG_LEDS_NET48XX)		+= leds-net48xx.o
 obj-$(CONFIG_LEDS_NET5501)		+= leds-net5501.o
 obj-$(CONFIG_LEDS_WRAP)			+= leds-wrap.o
diff --git a/drivers/leds/leds-ams-delta.c b/drivers/leds/leds-ams-delta.c
deleted file mode 100644
index 0742835..0000000
--- a/drivers/leds/leds-ams-delta.c
+++ /dev/null
@@ -1,126 +0,0 @@
-/*
- * LEDs driver for Amstrad Delta (E3)
- *
- * Copyright (C) 2006 Jonathan McDowell <noodles@earth.li>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/leds.h>
-#include <plat/board-ams-delta.h>
-
-/*
- * Our context
- */
-struct ams_delta_led {
-	struct led_classdev	cdev;
-	u8			bitmask;
-};
-
-static void ams_delta_led_set(struct led_classdev *led_cdev,
-		enum led_brightness value)
-{
-	struct ams_delta_led *led_dev =
-		container_of(led_cdev, struct ams_delta_led, cdev);
-
-	if (value)
-		ams_delta_latch1_write(led_dev->bitmask, led_dev->bitmask);
-	else
-		ams_delta_latch1_write(led_dev->bitmask, 0);
-}
-
-static struct ams_delta_led ams_delta_leds[] = {
-	{
-		.cdev		= {
-			.name		= "ams-delta::camera",
-			.brightness_set = ams_delta_led_set,
-		},
-		.bitmask	= AMS_DELTA_LATCH1_LED_CAMERA,
-	},
-	{
-		.cdev		= {
-			.name		= "ams-delta::advert",
-			.brightness_set = ams_delta_led_set,
-		},
-		.bitmask	= AMS_DELTA_LATCH1_LED_ADVERT,
-	},
-	{
-		.cdev		= {
-			.name		= "ams-delta::email",
-			.brightness_set = ams_delta_led_set,
-		},
-		.bitmask	= AMS_DELTA_LATCH1_LED_EMAIL,
-	},
-	{
-		.cdev		= {
-			.name		= "ams-delta::handsfree",
-			.brightness_set = ams_delta_led_set,
-		},
-		.bitmask	= AMS_DELTA_LATCH1_LED_HANDSFREE,
-	},
-	{
-		.cdev		= {
-			.name		= "ams-delta::voicemail",
-			.brightness_set = ams_delta_led_set,
-		},
-		.bitmask	= AMS_DELTA_LATCH1_LED_VOICEMAIL,
-	},
-	{
-		.cdev		= {
-			.name		= "ams-delta::voice",
-			.brightness_set = ams_delta_led_set,
-		},
-		.bitmask	= AMS_DELTA_LATCH1_LED_VOICE,
-	},
-};
-
-static int ams_delta_led_probe(struct platform_device *pdev)
-{
-	int i, ret;
-
-	for (i = 0; i < ARRAY_SIZE(ams_delta_leds); i++) {
-		ams_delta_leds[i].cdev.flags |= LED_CORE_SUSPENDRESUME;
-		ret = led_classdev_register(&pdev->dev,
-				&ams_delta_leds[i].cdev);
-		if (ret < 0)
-			goto fail;
-	}
-
-	return 0;
-fail:
-	while (--i >= 0)
-		led_classdev_unregister(&ams_delta_leds[i].cdev);
-	return ret;	
-}
-
-static int ams_delta_led_remove(struct platform_device *pdev)
-{
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(ams_delta_leds); i++)
-		led_classdev_unregister(&ams_delta_leds[i].cdev);
-
-	return 0;
-}
-
-static struct platform_driver ams_delta_led_driver = {
-	.probe		= ams_delta_led_probe,
-	.remove		= ams_delta_led_remove,
-	.driver		= {
-		.name = "ams-delta-led",
-		.owner = THIS_MODULE,
-	},
-};
-
-module_platform_driver(ams_delta_led_driver);
-
-MODULE_AUTHOR("Jonathan McDowell <noodles@earth.li>");
-MODULE_DESCRIPTION("Amstrad Delta LED driver");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:ams-delta-led");
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 0d955ff..304f2f9 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -1325,7 +1325,7 @@
 	if (ret)
 		goto unmap;
 
-	if (dev->irq[1] == NO_IRQ)
+	if (dev->irq[1] == NO_IRQ || !dev->irq[1])
 		host->singleirq = true;
 	else {
 		ret = request_irq(dev->irq[1], mmci_pio_irq, IRQF_SHARED,
diff --git a/drivers/mtd/nand/ams-delta.c b/drivers/mtd/nand/ams-delta.c
index 3197e97..7341695 100644
--- a/drivers/mtd/nand/ams-delta.c
+++ b/drivers/mtd/nand/ams-delta.c
@@ -26,7 +26,7 @@
 #include <asm/io.h>
 #include <mach/hardware.h>
 #include <asm/sizes.h>
-#include <asm/gpio.h>
+#include <linux/gpio.h>
 #include <plat/board-ams-delta.h>
 
 /*
@@ -34,8 +34,6 @@
  */
 static struct mtd_info *ams_delta_mtd = NULL;
 
-#define NAND_MASK (AMS_DELTA_LATCH2_NAND_NRE | AMS_DELTA_LATCH2_NAND_NWE | AMS_DELTA_LATCH2_NAND_CLE | AMS_DELTA_LATCH2_NAND_ALE | AMS_DELTA_LATCH2_NAND_NCE | AMS_DELTA_LATCH2_NAND_NWP)
-
 /*
  * Define partitions for flash devices
  */
@@ -68,10 +66,9 @@
 
 	writew(0, io_base + OMAP_MPUIO_IO_CNTL);
 	writew(byte, this->IO_ADDR_W);
-	ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_NWE, 0);
+	gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NWE, 0);
 	ndelay(40);
-	ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_NWE,
-			       AMS_DELTA_LATCH2_NAND_NWE);
+	gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NWE, 1);
 }
 
 static u_char ams_delta_read_byte(struct mtd_info *mtd)
@@ -80,12 +77,11 @@
 	struct nand_chip *this = mtd->priv;
 	void __iomem *io_base = this->priv;
 
-	ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_NRE, 0);
+	gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NRE, 0);
 	ndelay(40);
 	writew(~0, io_base + OMAP_MPUIO_IO_CNTL);
 	res = readw(this->IO_ADDR_R);
-	ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_NRE,
-			       AMS_DELTA_LATCH2_NAND_NRE);
+	gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NRE, 1);
 
 	return res;
 }
@@ -132,15 +128,12 @@
 {
 
 	if (ctrl & NAND_CTRL_CHANGE) {
-		unsigned long bits;
-
-		bits = (~ctrl & NAND_NCE) ? AMS_DELTA_LATCH2_NAND_NCE : 0;
-		bits |= (ctrl & NAND_CLE) ? AMS_DELTA_LATCH2_NAND_CLE : 0;
-		bits |= (ctrl & NAND_ALE) ? AMS_DELTA_LATCH2_NAND_ALE : 0;
-
-		ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_CLE |
-				AMS_DELTA_LATCH2_NAND_ALE |
-				AMS_DELTA_LATCH2_NAND_NCE, bits);
+		gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NCE,
+				(ctrl & NAND_NCE) == 0);
+		gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_CLE,
+				(ctrl & NAND_CLE) != 0);
+		gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_ALE,
+				(ctrl & NAND_ALE) != 0);
 	}
 
 	if (cmd != NAND_CMD_NONE)
@@ -152,6 +145,39 @@
 	return gpio_get_value(AMS_DELTA_GPIO_PIN_NAND_RB);
 }
 
+static const struct gpio _mandatory_gpio[] = {
+	{
+		.gpio	= AMS_DELTA_GPIO_PIN_NAND_NCE,
+		.flags	= GPIOF_OUT_INIT_HIGH,
+		.label	= "nand_nce",
+	},
+	{
+		.gpio	= AMS_DELTA_GPIO_PIN_NAND_NRE,
+		.flags	= GPIOF_OUT_INIT_HIGH,
+		.label	= "nand_nre",
+	},
+	{
+		.gpio	= AMS_DELTA_GPIO_PIN_NAND_NWP,
+		.flags	= GPIOF_OUT_INIT_HIGH,
+		.label	= "nand_nwp",
+	},
+	{
+		.gpio	= AMS_DELTA_GPIO_PIN_NAND_NWE,
+		.flags	= GPIOF_OUT_INIT_HIGH,
+		.label	= "nand_nwe",
+	},
+	{
+		.gpio	= AMS_DELTA_GPIO_PIN_NAND_ALE,
+		.flags	= GPIOF_OUT_INIT_LOW,
+		.label	= "nand_ale",
+	},
+	{
+		.gpio	= AMS_DELTA_GPIO_PIN_NAND_CLE,
+		.flags	= GPIOF_OUT_INIT_LOW,
+		.label	= "nand_cle",
+	},
+};
+
 /*
  * Main initialization routine
  */
@@ -223,10 +249,9 @@
 	platform_set_drvdata(pdev, io_base);
 
 	/* Set chip enabled, but  */
-	ams_delta_latch2_write(NAND_MASK, AMS_DELTA_LATCH2_NAND_NRE |
-					  AMS_DELTA_LATCH2_NAND_NWE |
-					  AMS_DELTA_LATCH2_NAND_NCE |
-					  AMS_DELTA_LATCH2_NAND_NWP);
+	err = gpio_request_array(_mandatory_gpio, ARRAY_SIZE(_mandatory_gpio));
+	if (err)
+		goto out_gpio;
 
 	/* Scan to find existence of the device */
 	if (nand_scan(ams_delta_mtd, 1)) {
@@ -241,7 +266,10 @@
 	goto out;
 
  out_mtd:
+	gpio_free_array(_mandatory_gpio, ARRAY_SIZE(_mandatory_gpio));
+out_gpio:
 	platform_set_drvdata(pdev, NULL);
+	gpio_free(AMS_DELTA_GPIO_PIN_NAND_RB);
 	iounmap(io_base);
 out_release_io:
 	release_mem_region(res->start, resource_size(res));
@@ -262,6 +290,8 @@
 	/* Release resources, unregister device */
 	nand_release(ams_delta_mtd);
 
+	gpio_free_array(_mandatory_gpio, ARRAY_SIZE(_mandatory_gpio));
+	gpio_free(AMS_DELTA_GPIO_PIN_NAND_RB);
 	iounmap(io_base);
 	release_mem_region(res->start, resource_size(res));
 
diff --git a/drivers/of/platform.c b/drivers/of/platform.c
index 63b3ec4..cae9477 100644
--- a/drivers/of/platform.c
+++ b/drivers/of/platform.c
@@ -253,7 +253,7 @@
 	if (!of_device_is_available(node))
 		return NULL;
 
-	dev = kzalloc(sizeof(*dev), GFP_KERNEL);
+	dev = amba_device_alloc(NULL, 0, 0);
 	if (!dev)
 		return NULL;
 
@@ -283,14 +283,14 @@
 	if (ret)
 		goto err_free;
 
-	ret = amba_device_register(dev, &iomem_resource);
+	ret = amba_device_add(dev, &iomem_resource);
 	if (ret)
 		goto err_free;
 
 	return dev;
 
 err_free:
-	kfree(dev);
+	amba_device_put(dev);
 	return NULL;
 }
 #else /* CONFIG_ARM_AMBA */
diff --git a/drivers/video/omap/lcd_ams_delta.c b/drivers/video/omap/lcd_ams_delta.c
index 0fdd6f6..d3a3113 100644
--- a/drivers/video/omap/lcd_ams_delta.c
+++ b/drivers/video/omap/lcd_ams_delta.c
@@ -25,6 +25,7 @@
 #include <linux/io.h>
 #include <linux/delay.h>
 #include <linux/lcd.h>
+#include <linux/gpio.h>
 
 #include <plat/board-ams-delta.h>
 #include <mach/hardware.h>
@@ -98,29 +99,41 @@
 
 /* omapfb panel section */
 
+static const struct gpio _gpios[] = {
+	{
+		.gpio	= AMS_DELTA_GPIO_PIN_LCD_VBLEN,
+		.flags	= GPIOF_OUT_INIT_LOW,
+		.label	= "lcd_vblen",
+	},
+	{
+		.gpio	= AMS_DELTA_GPIO_PIN_LCD_NDISP,
+		.flags	= GPIOF_OUT_INIT_LOW,
+		.label	= "lcd_ndisp",
+	},
+};
+
 static int ams_delta_panel_init(struct lcd_panel *panel,
 		struct omapfb_device *fbdev)
 {
-	return 0;
+	return gpio_request_array(_gpios, ARRAY_SIZE(_gpios));
 }
 
 static void ams_delta_panel_cleanup(struct lcd_panel *panel)
 {
+	gpio_free_array(_gpios, ARRAY_SIZE(_gpios));
 }
 
 static int ams_delta_panel_enable(struct lcd_panel *panel)
 {
-	ams_delta_latch2_write(AMS_DELTA_LATCH2_LCD_NDISP,
-			AMS_DELTA_LATCH2_LCD_NDISP);
-	ams_delta_latch2_write(AMS_DELTA_LATCH2_LCD_VBLEN,
-			AMS_DELTA_LATCH2_LCD_VBLEN);
+	gpio_set_value(AMS_DELTA_GPIO_PIN_LCD_NDISP, 1);
+	gpio_set_value(AMS_DELTA_GPIO_PIN_LCD_VBLEN, 1);
 	return 0;
 }
 
 static void ams_delta_panel_disable(struct lcd_panel *panel)
 {
-	ams_delta_latch2_write(AMS_DELTA_LATCH2_LCD_VBLEN, 0);
-	ams_delta_latch2_write(AMS_DELTA_LATCH2_LCD_NDISP, 0);
+	gpio_set_value(AMS_DELTA_GPIO_PIN_LCD_VBLEN, 0);
+	gpio_set_value(AMS_DELTA_GPIO_PIN_LCD_NDISP, 0);
 }
 
 static unsigned long ams_delta_panel_get_caps(struct lcd_panel *panel)
diff --git a/include/linux/amba/bus.h b/include/linux/amba/bus.h
index 724c69c..a9fab83 100644
--- a/include/linux/amba/bus.h
+++ b/include/linux/amba/bus.h
@@ -60,6 +60,9 @@
 
 int amba_driver_register(struct amba_driver *);
 void amba_driver_unregister(struct amba_driver *);
+struct amba_device *amba_device_alloc(const char *, resource_size_t, size_t);
+void amba_device_put(struct amba_device *);
+int amba_device_add(struct amba_device *, struct resource *);
 int amba_device_register(struct amba_device *, struct resource *);
 void amba_device_unregister(struct amba_device *);
 struct amba_device *amba_find_device(const char *, struct device *, unsigned int, unsigned int);
@@ -89,4 +92,37 @@
 #define amba_manf(d)	AMBA_MANF_BITS((d)->periphid)
 #define amba_part(d)	AMBA_PART_BITS((d)->periphid)
 
+#define __AMBA_DEV(busid, data, mask)				\
+	{							\
+		.coherent_dma_mask = mask,			\
+		.init_name = busid,				\
+		.platform_data = data,				\
+	}
+
+/*
+ * APB devices do not themselves have the ability to address memory,
+ * so DMA masks should be zero (much like USB peripheral devices.)
+ * The DMA controller DMA masks should be used instead (much like
+ * USB host controllers in conventional PCs.)
+ */
+#define AMBA_APB_DEVICE(name, busid, id, base, irqs, data)	\
+struct amba_device name##_device = {				\
+	.dev = __AMBA_DEV(busid, data, 0),			\
+	.res = DEFINE_RES_MEM(base, SZ_4K),			\
+	.irq = irqs,						\
+	.periphid = id,						\
+}
+
+/*
+ * AHB devices are DMA capable, so set their DMA masks
+ */
+#define AMBA_AHB_DEVICE(name, busid, id, base, irqs, data)	\
+struct amba_device name##_device = {				\
+	.dev = __AMBA_DEV(busid, data, ~0ULL),			\
+	.res = DEFINE_RES_MEM(base, SZ_4K),			\
+	.dma_mask = ~0ULL,					\
+	.irq = irqs,						\
+	.periphid = id,						\
+}
+
 #endif
diff --git a/sound/soc/omap/ams-delta.c b/sound/soc/omap/ams-delta.c
index a67f437..f610260 100644
--- a/sound/soc/omap/ams-delta.c
+++ b/sound/soc/omap/ams-delta.c
@@ -426,29 +426,6 @@
 };
 
 
-/* Board specific codec bias level control */
-static int ams_delta_set_bias_level(struct snd_soc_card *card,
-				    struct snd_soc_dapm_context *dapm,
-				    enum snd_soc_bias_level level)
-{
-	switch (level) {
-	case SND_SOC_BIAS_ON:
-	case SND_SOC_BIAS_PREPARE:
-	case SND_SOC_BIAS_STANDBY:
-		if (card->dapm.bias_level == SND_SOC_BIAS_OFF)
-			ams_delta_latch2_write(AMS_DELTA_LATCH2_MODEM_NRESET,
-						AMS_DELTA_LATCH2_MODEM_NRESET);
-		break;
-	case SND_SOC_BIAS_OFF:
-		if (card->dapm.bias_level != SND_SOC_BIAS_OFF)
-			ams_delta_latch2_write(AMS_DELTA_LATCH2_MODEM_NRESET,
-						0);
-	}
-	card->dapm.bias_level = level;
-
-	return 0;
-}
-
 /* Digital mute implemented using modem/CPU multiplexer.
  * Shares hardware with codec config pulse generation */
 static bool ams_delta_muted = 1;
@@ -512,9 +489,6 @@
 		ams_delta_ops.shutdown = ams_delta_shutdown;
 	}
 
-	/* Set codec bias level */
-	ams_delta_set_bias_level(card, dapm, SND_SOC_BIAS_STANDBY);
-
 	/* Add hook switch - can be used to control the codec from userspace
 	 * even if line discipline fails */
 	ret = snd_soc_jack_new(rtd->codec, "hook_switch",
@@ -598,7 +572,6 @@
 	.owner = THIS_MODULE,
 	.dai_link = &ams_delta_dai_link,
 	.num_links = 1,
-	.set_bias_level = ams_delta_set_bias_level,
 };
 
 /* Module init/exit */
@@ -635,7 +608,7 @@
 	platform_device_put(ams_delta_audio_platform_device);
 	return ret;
 }
-module_init(ams_delta_module_init);
+late_initcall(ams_delta_module_init);
 
 static void __exit ams_delta_module_exit(void)
 {
@@ -647,11 +620,6 @@
 			ARRAY_SIZE(ams_delta_hook_switch_gpios),
 			ams_delta_hook_switch_gpios);
 
-	/* Keep modem power on */
-	ams_delta_set_bias_level(&ams_delta_audio_card,
-				 &ams_delta_audio_card.rtd[0].codec->dapm,
-				 SND_SOC_BIAS_STANDBY);
-
 	platform_device_unregister(cx20442_platform_device);
 	platform_device_unregister(ams_delta_audio_platform_device);
 }