diff --git a/drivers/scsi/NCR5380.c b/drivers/scsi/NCR5380.c
index a59b71f..305330b 100644
--- a/drivers/scsi/NCR5380.c
+++ b/drivers/scsi/NCR5380.c
@@ -34,13 +34,6 @@
 /* Adapted for the Sun 3 by Sam Creasey. */
 
 /*
- * Further development / testing that should be done :
- *
- * 4.  Test SCSI-II tagged queueing (I have no devices which support
- * tagged queueing)
- */
-
-/*
  * Design
  *
  * This is a generic 5380 driver.  To use it on a different platform,
@@ -1257,14 +1250,6 @@
 	 * was true but before BSY was false during selection, the information
 	 * transfer phase should be a MESSAGE OUT phase so that we can send the
 	 * IDENTIFY message.
-	 *
-	 * If SCSI-II tagged queuing is enabled, we also send a SIMPLE_QUEUE_TAG
-	 * message (2 bytes) with a tag ID that we increment with every command
-	 * until it wraps back to 0.
-	 *
-	 * XXX - it turns out that there are some broken SCSI-II devices,
-	 * which claim to support tagged queuing but fail when more than
-	 * some number of commands are issued at once.
 	 */
 
 	/* Wait for start of REQ/ACK handshake */
@@ -1287,9 +1272,6 @@
 	tmp[0] = IDENTIFY(((instance->irq == NO_IRQ) ? 0 : 1), cmd->device->lun);
 
 	len = 1;
-	cmd->tag = 0;
-
-	/* Send message(s) */
 	data = tmp;
 	phase = PHASE_MSGOUT;
 	NCR5380_transfer_pio(instance, &phase, &len, &data);
@@ -2256,8 +2238,8 @@
 	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
 
 	hostdata->connected = tmp;
-	dsprintk(NDEBUG_RESELECTION, instance, "nexus established, target %d, lun %llu, tag %d\n",
-	         scmd_id(tmp), tmp->device->lun, tmp->tag);
+	dsprintk(NDEBUG_RESELECTION, instance, "nexus established, target %d, lun %llu\n",
+	         scmd_id(tmp), tmp->device->lun);
 }
 
 /**
diff --git a/drivers/scsi/NCR5380.h b/drivers/scsi/NCR5380.h
index 8adf7377d..5c2411f 100644
--- a/drivers/scsi/NCR5380.h
+++ b/drivers/scsi/NCR5380.h
@@ -199,13 +199,6 @@
 
 #define PHASE_SR_TO_TCR(phase) ((phase) >> 2)
 
-/* 
- * "Special" value for the (unsigned char) command tag, to indicate
- * I_T_L nexus instead of I_T_L_Q.
- */
-
-#define TAG_NONE	0xff
-
 /*
  * These are "special" values for the irq and dma_channel fields of the 
  * Scsi_Host structure
@@ -223,17 +216,8 @@
 #define FLAG_DMA_FIXUP			1	/* Use DMA errata workarounds */
 #define FLAG_NO_PSEUDO_DMA		8	/* Inhibit DMA */
 #define FLAG_LATE_DMA_SETUP		32	/* Setup NCR before DMA H/W */
-#define FLAG_TAGGED_QUEUING		64	/* as X3T9.2 spelled it */
 #define FLAG_TOSHIBA_DELAY		128	/* Allow for borken CD-ROMs */
 
-#ifdef SUPPORT_TAGS
-struct tag_alloc {
-	DECLARE_BITMAP(allocated, MAX_TAGS);
-	int nr_allocated;
-	int queue_size;
-};
-#endif
-
 struct NCR5380_hostdata {
 	NCR5380_implementation_fields;		/* implementation specific */
 	struct Scsi_Host *host;			/* Host backpointer */
@@ -254,9 +238,6 @@
 	int read_overruns;                /* number of bytes to cut from a
 	                                   * transfer to handle chip overruns */
 	struct work_struct main_task;
-#ifdef SUPPORT_TAGS
-	struct tag_alloc TagAlloc[8][8];	/* 8 targets and 8 LUNs */
-#endif
 	struct workqueue_struct *work_q;
 	unsigned long accesses_per_ms;	/* chip register accesses per ms */
 };
diff --git a/drivers/scsi/atari_NCR5380.c b/drivers/scsi/atari_NCR5380.c
deleted file mode 100644
index 4101d2d..0000000
--- a/drivers/scsi/atari_NCR5380.c
+++ /dev/null
@@ -1,2632 +0,0 @@
-/*
- * NCR 5380 generic driver routines.  These should make it *trivial*
- * to implement 5380 SCSI drivers under Linux with a non-trantor
- * architecture.
- *
- * Note that these routines also work with NR53c400 family chips.
- *
- * Copyright 1993, Drew Eckhardt
- * Visionary Computing
- * (Unix and Linux consulting and custom programming)
- * drew@colorado.edu
- * +1 (303) 666-5836
- *
- * For more information, please consult
- *
- * NCR 5380 Family
- * SCSI Protocol Controller
- * Databook
- *
- * NCR Microelectronics
- * 1635 Aeroplaza Drive
- * Colorado Springs, CO 80916
- * 1+ (719) 578-3400
- * 1+ (800) 334-5454
- */
-
-/* Ported to Atari by Roman Hodek and others. */
-
-/* Adapted for the sun3 by Sam Creasey. */
-
-/*
- * Design
- *
- * This is a generic 5380 driver.  To use it on a different platform,
- * one simply writes appropriate system specific macros (ie, data
- * transfer - some PC's will use the I/O bus, 68K's must use
- * memory mapped) and drops this file in their 'C' wrapper.
- *
- * As far as command queueing, two queues are maintained for
- * each 5380 in the system - commands that haven't been issued yet,
- * and commands that are currently executing.  This means that an
- * unlimited number of commands may be queued, letting
- * more commands propagate from the higher driver levels giving higher
- * throughput.  Note that both I_T_L and I_T_L_Q nexuses are supported,
- * allowing multiple commands to propagate all the way to a SCSI-II device
- * while a command is already executing.
- *
- *
- * Issues specific to the NCR5380 :
- *
- * When used in a PIO or pseudo-dma mode, the NCR5380 is a braindead
- * piece of hardware that requires you to sit in a loop polling for
- * the REQ signal as long as you are connected.  Some devices are
- * brain dead (ie, many TEXEL CD ROM drives) and won't disconnect
- * while doing long seek operations. [...] These
- * broken devices are the exception rather than the rule and I'd rather
- * spend my time optimizing for the normal case.
- *
- * Architecture :
- *
- * At the heart of the design is a coroutine, NCR5380_main,
- * which is started from a workqueue for each NCR5380 host in the
- * system.  It attempts to establish I_T_L or I_T_L_Q nexuses by
- * removing the commands from the issue queue and calling
- * NCR5380_select() if a nexus is not established.
- *
- * Once a nexus is established, the NCR5380_information_transfer()
- * phase goes through the various phases as instructed by the target.
- * if the target goes into MSG IN and sends a DISCONNECT message,
- * the command structure is placed into the per instance disconnected
- * queue, and NCR5380_main tries to find more work.  If the target is
- * idle for too long, the system will try to sleep.
- *
- * If a command has disconnected, eventually an interrupt will trigger,
- * calling NCR5380_intr()  which will in turn call NCR5380_reselect
- * to reestablish a nexus.  This will run main if necessary.
- *
- * On command termination, the done function will be called as
- * appropriate.
- *
- * SCSI pointers are maintained in the SCp field of SCSI command
- * structures, being initialized after the command is connected
- * in NCR5380_select, and set as appropriate in NCR5380_information_transfer.
- * Note that in violation of the standard, an implicit SAVE POINTERS operation
- * is done, since some BROKEN disks fail to issue an explicit SAVE POINTERS.
- */
-
-/*
- * Using this file :
- * This file a skeleton Linux SCSI driver for the NCR 5380 series
- * of chips.  To use it, you write an architecture specific functions
- * and macros and include this file in your driver.
- *
- * These macros control options :
- * AUTOSENSE - if defined, REQUEST SENSE will be performed automatically
- * for commands that return with a CHECK CONDITION status.
- *
- * DIFFERENTIAL - if defined, NCR53c81 chips will use external differential
- * transceivers.
- *
- * REAL_DMA - if defined, REAL DMA is used during the data transfer phases.
- *
- * SUPPORT_TAGS - if defined, SCSI-2 tagged queuing is used where possible
- *
- * These macros MUST be defined :
- *
- * NCR5380_read(register)  - read from the specified register
- *
- * NCR5380_write(register, value) - write to the specific register
- *
- * NCR5380_implementation_fields  - additional fields needed for this
- * specific implementation of the NCR5380
- *
- * Either real DMA *or* pseudo DMA may be implemented
- * Note that the DMA setup functions should return the number of bytes
- * that they were able to program the controller for.
- *
- * NCR5380_dma_write_setup(instance, src, count) - initialize
- * NCR5380_dma_read_setup(instance, dst, count) - initialize
- * NCR5380_dma_residual(instance); - residual count
- *
- * PSEUDO functions :
- * NCR5380_pwrite(instance, src, count)
- * NCR5380_pread(instance, dst, count);
- *
- * The generic driver is initialized by calling NCR5380_init(instance),
- * after setting the appropriate host specific fields and ID.  If the
- * driver wishes to autoprobe for an IRQ line, the NCR5380_probe_irq(instance,
- * possible) function may be used.
- */
-
-static int do_abort(struct Scsi_Host *);
-static void do_reset(struct Scsi_Host *);
-
-#ifdef SUPPORT_TAGS
-
-/*
- * Functions for handling tagged queuing
- * =====================================
- *
- * ++roman (01/96): Now I've implemented SCSI-2 tagged queuing. Some notes:
- *
- * Using consecutive numbers for the tags is no good idea in my eyes. There
- * could be wrong re-usings if the counter (8 bit!) wraps and some early
- * command has been preempted for a long time. My solution: a bitfield for
- * remembering used tags.
- *
- * There's also the problem that each target has a certain queue size, but we
- * cannot know it in advance :-( We just see a QUEUE_FULL status being
- * returned. So, in this case, the driver internal queue size assumption is
- * reduced to the number of active tags if QUEUE_FULL is returned by the
- * target.
- *
- * We're also not allowed running tagged commands as long as an untagged
- * command is active. And REQUEST SENSE commands after a contingent allegiance
- * condition _must_ be untagged. To keep track whether an untagged command has
- * been issued, the host->busy array is still employed, as it is without
- * support for tagged queuing.
- *
- * One could suspect that there are possible race conditions between
- * is_lun_busy(), cmd_get_tag() and cmd_free_tag(). But I think this isn't the
- * case: is_lun_busy() and cmd_get_tag() are both called from NCR5380_main(),
- * which already guaranteed to be running at most once. It is also the only
- * place where tags/LUNs are allocated. So no other allocation can slip
- * between that pair, there could only happen a reselection, which can free a
- * tag, but that doesn't hurt. Only the sequence in cmd_free_tag() becomes
- * important: the tag bit must be cleared before 'nr_allocated' is decreased.
- */
-
-static void __init init_tags(struct NCR5380_hostdata *hostdata)
-{
-	int target, lun;
-	struct tag_alloc *ta;
-
-	if (!(hostdata->flags & FLAG_TAGGED_QUEUING))
-		return;
-
-	for (target = 0; target < 8; ++target) {
-		for (lun = 0; lun < 8; ++lun) {
-			ta = &hostdata->TagAlloc[target][lun];
-			bitmap_zero(ta->allocated, MAX_TAGS);
-			ta->nr_allocated = 0;
-			/* At the beginning, assume the maximum queue size we could
-			 * support (MAX_TAGS). This value will be decreased if the target
-			 * returns QUEUE_FULL status.
-			 */
-			ta->queue_size = MAX_TAGS;
-		}
-	}
-}
-
-
-/* Check if we can issue a command to this LUN: First see if the LUN is marked
- * busy by an untagged command. If the command should use tagged queuing, also
- * check that there is a free tag and the target's queue won't overflow. This
- * function should be called with interrupts disabled to avoid race
- * conditions.
- */
-
-static int is_lun_busy(struct scsi_cmnd *cmd, int should_be_tagged)
-{
-	u8 lun = cmd->device->lun;
-	struct Scsi_Host *instance = cmd->device->host;
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-
-	if (hostdata->busy[cmd->device->id] & (1 << lun))
-		return 1;
-	if (!should_be_tagged ||
-	    !(hostdata->flags & FLAG_TAGGED_QUEUING) ||
-	    !cmd->device->tagged_supported)
-		return 0;
-	if (hostdata->TagAlloc[scmd_id(cmd)][lun].nr_allocated >=
-	    hostdata->TagAlloc[scmd_id(cmd)][lun].queue_size) {
-		dsprintk(NDEBUG_TAGS, instance, "target %d lun %d: no free tags\n",
-		         scmd_id(cmd), lun);
-		return 1;
-	}
-	return 0;
-}
-
-
-/* Allocate a tag for a command (there are no checks anymore, check_lun_busy()
- * must be called before!), or reserve the LUN in 'busy' if the command is
- * untagged.
- */
-
-static void cmd_get_tag(struct scsi_cmnd *cmd, int should_be_tagged)
-{
-	u8 lun = cmd->device->lun;
-	struct Scsi_Host *instance = cmd->device->host;
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-
-	/* If we or the target don't support tagged queuing, allocate the LUN for
-	 * an untagged command.
-	 */
-	if (!should_be_tagged ||
-	    !(hostdata->flags & FLAG_TAGGED_QUEUING) ||
-	    !cmd->device->tagged_supported) {
-		cmd->tag = TAG_NONE;
-		hostdata->busy[cmd->device->id] |= (1 << lun);
-		dsprintk(NDEBUG_TAGS, instance, "target %d lun %d now allocated by untagged command\n",
-		         scmd_id(cmd), lun);
-	} else {
-		struct tag_alloc *ta = &hostdata->TagAlloc[scmd_id(cmd)][lun];
-
-		cmd->tag = find_first_zero_bit(ta->allocated, MAX_TAGS);
-		set_bit(cmd->tag, ta->allocated);
-		ta->nr_allocated++;
-		dsprintk(NDEBUG_TAGS, instance, "using tag %d for target %d lun %d (%d tags allocated)\n",
-		         cmd->tag, scmd_id(cmd), lun, ta->nr_allocated);
-	}
-}
-
-
-/* Mark the tag of command 'cmd' as free, or in case of an untagged command,
- * unlock the LUN.
- */
-
-static void cmd_free_tag(struct scsi_cmnd *cmd)
-{
-	u8 lun = cmd->device->lun;
-	struct Scsi_Host *instance = cmd->device->host;
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-
-	if (cmd->tag == TAG_NONE) {
-		hostdata->busy[cmd->device->id] &= ~(1 << lun);
-		dsprintk(NDEBUG_TAGS, instance, "target %d lun %d untagged cmd freed\n",
-		         scmd_id(cmd), lun);
-	} else if (cmd->tag >= MAX_TAGS) {
-		shost_printk(KERN_NOTICE, instance,
-		             "trying to free bad tag %d!\n", cmd->tag);
-	} else {
-		struct tag_alloc *ta = &hostdata->TagAlloc[scmd_id(cmd)][lun];
-		clear_bit(cmd->tag, ta->allocated);
-		ta->nr_allocated--;
-		dsprintk(NDEBUG_TAGS, instance, "freed tag %d for target %d lun %d\n",
-		         cmd->tag, scmd_id(cmd), lun);
-	}
-}
-
-
-static void free_all_tags(struct NCR5380_hostdata *hostdata)
-{
-	int target, lun;
-	struct tag_alloc *ta;
-
-	if (!(hostdata->flags & FLAG_TAGGED_QUEUING))
-		return;
-
-	for (target = 0; target < 8; ++target) {
-		for (lun = 0; lun < 8; ++lun) {
-			ta = &hostdata->TagAlloc[target][lun];
-			bitmap_zero(ta->allocated, MAX_TAGS);
-			ta->nr_allocated = 0;
-		}
-	}
-}
-
-#endif /* SUPPORT_TAGS */
-
-/**
- * merge_contiguous_buffers - coalesce scatter-gather list entries
- * @cmd: command requesting IO
- *
- * Try to merge several scatter-gather buffers into one DMA transfer.
- * This is possible if the scatter buffers lie on physically
- * contiguous addresses. The first scatter-gather buffer's data are
- * assumed to be already transferred into cmd->SCp.this_residual.
- * Every buffer merged avoids an interrupt and a DMA setup operation.
- */
-
-static void merge_contiguous_buffers(struct scsi_cmnd *cmd)
-{
-#if !defined(CONFIG_SUN3)
-	unsigned long endaddr;
-#if (NDEBUG & NDEBUG_MERGING)
-	unsigned long oldlen = cmd->SCp.this_residual;
-	int cnt = 1;
-#endif
-
-	for (endaddr = virt_to_phys(cmd->SCp.ptr + cmd->SCp.this_residual - 1) + 1;
-	     cmd->SCp.buffers_residual &&
-	     virt_to_phys(sg_virt(&cmd->SCp.buffer[1])) == endaddr;) {
-		dprintk(NDEBUG_MERGING, "VTOP(%p) == %08lx -> merging\n",
-			   page_address(sg_page(&cmd->SCp.buffer[1])), endaddr);
-#if (NDEBUG & NDEBUG_MERGING)
-		++cnt;
-#endif
-		++cmd->SCp.buffer;
-		--cmd->SCp.buffers_residual;
-		cmd->SCp.this_residual += cmd->SCp.buffer->length;
-		endaddr += cmd->SCp.buffer->length;
-	}
-#if (NDEBUG & NDEBUG_MERGING)
-	if (oldlen != cmd->SCp.this_residual)
-		dprintk(NDEBUG_MERGING, "merged %d buffers from %p, new length %08x\n",
-			   cnt, cmd->SCp.ptr, cmd->SCp.this_residual);
-#endif
-#endif /* !defined(CONFIG_SUN3) */
-}
-
-/**
- * initialize_SCp - init the scsi pointer field
- * @cmd: command block to set up
- *
- * Set up the internal fields in the SCSI command.
- */
-
-static inline void initialize_SCp(struct scsi_cmnd *cmd)
-{
-	/*
-	 * Initialize the Scsi Pointer field so that all of the commands in the
-	 * various queues are valid.
-	 */
-
-	if (scsi_bufflen(cmd)) {
-		cmd->SCp.buffer = scsi_sglist(cmd);
-		cmd->SCp.buffers_residual = scsi_sg_count(cmd) - 1;
-		cmd->SCp.ptr = sg_virt(cmd->SCp.buffer);
-		cmd->SCp.this_residual = cmd->SCp.buffer->length;
-
-		merge_contiguous_buffers(cmd);
-	} else {
-		cmd->SCp.buffer = NULL;
-		cmd->SCp.buffers_residual = 0;
-		cmd->SCp.ptr = NULL;
-		cmd->SCp.this_residual = 0;
-	}
-
-	cmd->SCp.Status = 0;
-	cmd->SCp.Message = 0;
-}
-
-/**
- * NCR5380_poll_politely2 - wait for two chip register values
- * @instance: controller to poll
- * @reg1: 5380 register to poll
- * @bit1: Bitmask to check
- * @val1: Expected value
- * @reg2: Second 5380 register to poll
- * @bit2: Second bitmask to check
- * @val2: Second expected value
- * @wait: Time-out in jiffies
- *
- * Polls the chip in a reasonably efficient manner waiting for an
- * event to occur. After a short quick poll we begin to yield the CPU
- * (if possible). In irq contexts the time-out is arbitrarily limited.
- * Callers may hold locks as long as they are held in irq mode.
- *
- * Returns 0 if either or both event(s) occurred otherwise -ETIMEDOUT.
- */
-
-static int NCR5380_poll_politely2(struct Scsi_Host *instance,
-                                  int reg1, int bit1, int val1,
-                                  int reg2, int bit2, int val2, int wait)
-{
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-	unsigned long deadline = jiffies + wait;
-	unsigned long n;
-
-	/* Busy-wait for up to 10 ms */
-	n = min(10000U, jiffies_to_usecs(wait));
-	n *= hostdata->accesses_per_ms;
-	n /= 2000;
-	do {
-		if ((NCR5380_read(reg1) & bit1) == val1)
-			return 0;
-		if ((NCR5380_read(reg2) & bit2) == val2)
-			return 0;
-		cpu_relax();
-	} while (n--);
-
-	if (irqs_disabled() || in_interrupt())
-		return -ETIMEDOUT;
-
-	/* Repeatedly sleep for 1 ms until deadline */
-	while (time_is_after_jiffies(deadline)) {
-		schedule_timeout_uninterruptible(1);
-		if ((NCR5380_read(reg1) & bit1) == val1)
-			return 0;
-		if ((NCR5380_read(reg2) & bit2) == val2)
-			return 0;
-	}
-
-	return -ETIMEDOUT;
-}
-
-static inline int NCR5380_poll_politely(struct Scsi_Host *instance,
-                                        int reg, int bit, int val, int wait)
-{
-	return NCR5380_poll_politely2(instance, reg, bit, val,
-	                                        reg, bit, val, wait);
-}
-
-#if NDEBUG
-static struct {
-	unsigned char mask;
-	const char *name;
-} signals[] = {
-	{SR_DBP, "PARITY"},
-	{SR_RST, "RST"},
-	{SR_BSY, "BSY"},
-	{SR_REQ, "REQ"},
-	{SR_MSG, "MSG"},
-	{SR_CD, "CD"},
-	{SR_IO, "IO"},
-	{SR_SEL, "SEL"},
-	{0, NULL}
-},
-basrs[] = {
-	{BASR_ATN, "ATN"},
-	{BASR_ACK, "ACK"},
-	{0, NULL}
-},
-icrs[] = {
-	{ICR_ASSERT_RST, "ASSERT RST"},
-	{ICR_ASSERT_ACK, "ASSERT ACK"},
-	{ICR_ASSERT_BSY, "ASSERT BSY"},
-	{ICR_ASSERT_SEL, "ASSERT SEL"},
-	{ICR_ASSERT_ATN, "ASSERT ATN"},
-	{ICR_ASSERT_DATA, "ASSERT DATA"},
-	{0, NULL}
-},
-mrs[] = {
-	{MR_BLOCK_DMA_MODE, "MODE BLOCK DMA"},
-	{MR_TARGET, "MODE TARGET"},
-	{MR_ENABLE_PAR_CHECK, "MODE PARITY CHECK"},
-	{MR_ENABLE_PAR_INTR, "MODE PARITY INTR"},
-	{MR_ENABLE_EOP_INTR, "MODE EOP INTR"},
-	{MR_MONITOR_BSY, "MODE MONITOR BSY"},
-	{MR_DMA_MODE, "MODE DMA"},
-	{MR_ARBITRATE, "MODE ARBITRATION"},
-	{0, NULL}
-};
-
-/**
- * NCR5380_print - print scsi bus signals
- * @instance: adapter state to dump
- *
- * Print the SCSI bus signals for debugging purposes
- */
-
-static void NCR5380_print(struct Scsi_Host *instance)
-{
-	unsigned char status, data, basr, mr, icr, i;
-
-	data = NCR5380_read(CURRENT_SCSI_DATA_REG);
-	status = NCR5380_read(STATUS_REG);
-	mr = NCR5380_read(MODE_REG);
-	icr = NCR5380_read(INITIATOR_COMMAND_REG);
-	basr = NCR5380_read(BUS_AND_STATUS_REG);
-
-	printk("STATUS_REG: %02x ", status);
-	for (i = 0; signals[i].mask; ++i)
-		if (status & signals[i].mask)
-			printk(",%s", signals[i].name);
-	printk("\nBASR: %02x ", basr);
-	for (i = 0; basrs[i].mask; ++i)
-		if (basr & basrs[i].mask)
-			printk(",%s", basrs[i].name);
-	printk("\nICR: %02x ", icr);
-	for (i = 0; icrs[i].mask; ++i)
-		if (icr & icrs[i].mask)
-			printk(",%s", icrs[i].name);
-	printk("\nMODE: %02x ", mr);
-	for (i = 0; mrs[i].mask; ++i)
-		if (mr & mrs[i].mask)
-			printk(",%s", mrs[i].name);
-	printk("\n");
-}
-
-static struct {
-	unsigned char value;
-	const char *name;
-} phases[] = {
-	{PHASE_DATAOUT, "DATAOUT"},
-	{PHASE_DATAIN, "DATAIN"},
-	{PHASE_CMDOUT, "CMDOUT"},
-	{PHASE_STATIN, "STATIN"},
-	{PHASE_MSGOUT, "MSGOUT"},
-	{PHASE_MSGIN, "MSGIN"},
-	{PHASE_UNKNOWN, "UNKNOWN"}
-};
-
-/**
- * NCR5380_print_phase - show SCSI phase
- * @instance: adapter to dump
- *
- * Print the current SCSI phase for debugging purposes
- */
-
-static void NCR5380_print_phase(struct Scsi_Host *instance)
-{
-	unsigned char status;
-	int i;
-
-	status = NCR5380_read(STATUS_REG);
-	if (!(status & SR_REQ))
-		shost_printk(KERN_DEBUG, instance, "REQ not asserted, phase unknown.\n");
-	else {
-		for (i = 0; (phases[i].value != PHASE_UNKNOWN) &&
-		     (phases[i].value != (status & PHASE_MASK)); ++i)
-			;
-		shost_printk(KERN_DEBUG, instance, "phase %s\n", phases[i].name);
-	}
-}
-#endif
-
-/**
- * NCR58380_info - report driver and host information
- * @instance: relevant scsi host instance
- *
- * For use as the host template info() handler.
- */
-
-static const char *NCR5380_info(struct Scsi_Host *instance)
-{
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-
-	return hostdata->info;
-}
-
-static void prepare_info(struct Scsi_Host *instance)
-{
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-
-	snprintf(hostdata->info, sizeof(hostdata->info),
-	         "%s, io_port 0x%lx, n_io_port %d, "
-	         "base 0x%lx, irq %d, "
-	         "can_queue %d, cmd_per_lun %d, "
-	         "sg_tablesize %d, this_id %d, "
-	         "flags { %s%s}, "
-	         "options { %s} ",
-	         instance->hostt->name, instance->io_port, instance->n_io_port,
-	         instance->base, instance->irq,
-	         instance->can_queue, instance->cmd_per_lun,
-	         instance->sg_tablesize, instance->this_id,
-	         hostdata->flags & FLAG_TAGGED_QUEUING ? "TAGGED_QUEUING " : "",
-	         hostdata->flags & FLAG_TOSHIBA_DELAY  ? "TOSHIBA_DELAY "  : "",
-#ifdef DIFFERENTIAL
-	         "DIFFERENTIAL "
-#endif
-#ifdef PARITY
-	         "PARITY "
-#endif
-#ifdef SUPPORT_TAGS
-	         "SUPPORT_TAGS "
-#endif
-	         "");
-}
-
-/**
- * NCR5380_init - initialise an NCR5380
- * @instance: adapter to configure
- * @flags: control flags
- *
- * Initializes *instance and corresponding 5380 chip,
- * with flags OR'd into the initial flags value.
- *
- * Notes : I assume that the host, hostno, and id bits have been
- * set correctly. I don't care about the irq and other fields.
- *
- * Returns 0 for success
- */
-
-static int __init NCR5380_init(struct Scsi_Host *instance, int flags)
-{
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-	int i;
-	unsigned long deadline;
-
-	hostdata->host = instance;
-	hostdata->id_mask = 1 << instance->this_id;
-	hostdata->id_higher_mask = 0;
-	for (i = hostdata->id_mask; i <= 0x80; i <<= 1)
-		if (i > hostdata->id_mask)
-			hostdata->id_higher_mask |= i;
-	for (i = 0; i < 8; ++i)
-		hostdata->busy[i] = 0;
-#ifdef SUPPORT_TAGS
-	init_tags(hostdata);
-#endif
-	hostdata->dma_len = 0;
-
-	spin_lock_init(&hostdata->lock);
-	hostdata->connected = NULL;
-	hostdata->sensing = NULL;
-	INIT_LIST_HEAD(&hostdata->autosense);
-	INIT_LIST_HEAD(&hostdata->unissued);
-	INIT_LIST_HEAD(&hostdata->disconnected);
-
-	hostdata->flags = flags;
-
-	INIT_WORK(&hostdata->main_task, NCR5380_main);
-	hostdata->work_q = alloc_workqueue("ncr5380_%d",
-	                        WQ_UNBOUND | WQ_MEM_RECLAIM,
-	                        1, instance->host_no);
-	if (!hostdata->work_q)
-		return -ENOMEM;
-
-	prepare_info(instance);
-
-	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-	NCR5380_write(MODE_REG, MR_BASE);
-	NCR5380_write(TARGET_COMMAND_REG, 0);
-	NCR5380_write(SELECT_ENABLE_REG, 0);
-
-	/* Calibrate register polling loop */
-	i = 0;
-	deadline = jiffies + 1;
-	do {
-		cpu_relax();
-	} while (time_is_after_jiffies(deadline));
-	deadline += msecs_to_jiffies(256);
-	do {
-		NCR5380_read(STATUS_REG);
-		++i;
-		cpu_relax();
-	} while (time_is_after_jiffies(deadline));
-	hostdata->accesses_per_ms = i / 256;
-
-	return 0;
-}
-
-/**
- * NCR5380_maybe_reset_bus - Detect and correct bus wedge problems.
- * @instance: adapter to check
- *
- * If the system crashed, it may have crashed with a connected target and
- * the SCSI bus busy. Check for BUS FREE phase. If not, try to abort the
- * currently established nexus, which we know nothing about. Failing that
- * do a bus reset.
- *
- * Note that a bus reset will cause the chip to assert IRQ.
- *
- * Returns 0 if successful, otherwise -ENXIO.
- */
-
-static int NCR5380_maybe_reset_bus(struct Scsi_Host *instance)
-{
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-	int pass;
-
-	for (pass = 1; (NCR5380_read(STATUS_REG) & SR_BSY) && pass <= 6; ++pass) {
-		switch (pass) {
-		case 1:
-		case 3:
-		case 5:
-			shost_printk(KERN_ERR, instance, "SCSI bus busy, waiting up to five seconds\n");
-			NCR5380_poll_politely(instance,
-			                      STATUS_REG, SR_BSY, 0, 5 * HZ);
-			break;
-		case 2:
-			shost_printk(KERN_ERR, instance, "bus busy, attempting abort\n");
-			do_abort(instance);
-			break;
-		case 4:
-			shost_printk(KERN_ERR, instance, "bus busy, attempting reset\n");
-			do_reset(instance);
-			/* Wait after a reset; the SCSI standard calls for
-			 * 250ms, we wait 500ms to be on the safe side.
-			 * But some Toshiba CD-ROMs need ten times that.
-			 */
-			if (hostdata->flags & FLAG_TOSHIBA_DELAY)
-				msleep(2500);
-			else
-				msleep(500);
-			break;
-		case 6:
-			shost_printk(KERN_ERR, instance, "bus locked solid\n");
-			return -ENXIO;
-		}
-	}
-	return 0;
-}
-
-/**
- * NCR5380_exit - remove an NCR5380
- * @instance: adapter to remove
- *
- * Assumes that no more work can be queued (e.g. by NCR5380_intr).
- */
-
-static void NCR5380_exit(struct Scsi_Host *instance)
-{
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-
-	cancel_work_sync(&hostdata->main_task);
-	destroy_workqueue(hostdata->work_q);
-}
-
-/**
- * complete_cmd - finish processing a command and return it to the SCSI ML
- * @instance: the host instance
- * @cmd: command to complete
- */
-
-static void complete_cmd(struct Scsi_Host *instance,
-                         struct scsi_cmnd *cmd)
-{
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-
-	dsprintk(NDEBUG_QUEUES, instance, "complete_cmd: cmd %p\n", cmd);
-
-	if (hostdata->sensing == cmd) {
-		/* Autosense processing ends here */
-		if ((cmd->result & 0xff) != SAM_STAT_GOOD) {
-			scsi_eh_restore_cmnd(cmd, &hostdata->ses);
-			set_host_byte(cmd, DID_ERROR);
-		} else
-			scsi_eh_restore_cmnd(cmd, &hostdata->ses);
-		hostdata->sensing = NULL;
-	}
-
-#ifdef SUPPORT_TAGS
-	cmd_free_tag(cmd);
-#else
-	hostdata->busy[scmd_id(cmd)] &= ~(1 << cmd->device->lun);
-#endif
-	cmd->scsi_done(cmd);
-}
-
-/**
- * NCR5380_queue_command - queue a command
- * @instance: the relevant SCSI adapter
- * @cmd: SCSI command
- *
- * cmd is added to the per-instance issue queue, with minor
- * twiddling done to the host specific fields of cmd.  If the
- * main coroutine is not running, it is restarted.
- */
-
-static int NCR5380_queue_command(struct Scsi_Host *instance,
-                                 struct scsi_cmnd *cmd)
-{
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-	struct NCR5380_cmd *ncmd = scsi_cmd_priv(cmd);
-	unsigned long flags;
-
-#if (NDEBUG & NDEBUG_NO_WRITE)
-	switch (cmd->cmnd[0]) {
-	case WRITE_6:
-	case WRITE_10:
-		shost_printk(KERN_DEBUG, instance, "WRITE attempted with NDEBUG_NO_WRITE set\n");
-		cmd->result = (DID_ERROR << 16);
-		cmd->scsi_done(cmd);
-		return 0;
-	}
-#endif /* (NDEBUG & NDEBUG_NO_WRITE) */
-
-	cmd->result = 0;
-
-	/*
-	 * ++roman: Just disabling the NCR interrupt isn't sufficient here,
-	 * because also a timer int can trigger an abort or reset, which would
-	 * alter queues and touch the lock.
-	 */
-	if (!NCR5380_acquire_dma_irq(instance))
-		return SCSI_MLQUEUE_HOST_BUSY;
-
-	spin_lock_irqsave(&hostdata->lock, flags);
-
-	/*
-	 * Insert the cmd into the issue queue. Note that REQUEST SENSE
-	 * commands are added to the head of the queue since any command will
-	 * clear the contingent allegiance condition that exists and the
-	 * sense data is only guaranteed to be valid while the condition exists.
-	 */
-
-	if (cmd->cmnd[0] == REQUEST_SENSE)
-		list_add(&ncmd->list, &hostdata->unissued);
-	else
-		list_add_tail(&ncmd->list, &hostdata->unissued);
-
-	spin_unlock_irqrestore(&hostdata->lock, flags);
-
-	dsprintk(NDEBUG_QUEUES, instance, "command %p added to %s of queue\n",
-	         cmd, (cmd->cmnd[0] == REQUEST_SENSE) ? "head" : "tail");
-
-	/* Kick off command processing */
-	queue_work(hostdata->work_q, &hostdata->main_task);
-	return 0;
-}
-
-static inline void maybe_release_dma_irq(struct Scsi_Host *instance)
-{
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-
-	/* Caller does the locking needed to set & test these data atomically */
-	if (list_empty(&hostdata->disconnected) &&
-	    list_empty(&hostdata->unissued) &&
-	    list_empty(&hostdata->autosense) &&
-	    !hostdata->connected &&
-	    !hostdata->selecting)
-		NCR5380_release_dma_irq(instance);
-}
-
-/**
- * dequeue_next_cmd - dequeue a command for processing
- * @instance: the scsi host instance
- *
- * Priority is given to commands on the autosense queue. These commands
- * need autosense because of a CHECK CONDITION result.
- *
- * Returns a command pointer if a command is found for a target that is
- * not already busy. Otherwise returns NULL.
- */
-
-static struct scsi_cmnd *dequeue_next_cmd(struct Scsi_Host *instance)
-{
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-	struct NCR5380_cmd *ncmd;
-	struct scsi_cmnd *cmd;
-
-	if (hostdata->sensing || list_empty(&hostdata->autosense)) {
-		list_for_each_entry(ncmd, &hostdata->unissued, list) {
-			cmd = NCR5380_to_scmd(ncmd);
-			dsprintk(NDEBUG_QUEUES, instance, "dequeue: cmd=%p target=%d busy=0x%02x lun=%llu\n",
-			         cmd, scmd_id(cmd), hostdata->busy[scmd_id(cmd)], cmd->device->lun);
-
-			if (
-#ifdef SUPPORT_TAGS
-			    !is_lun_busy(cmd, 1)
-#else
-			    !(hostdata->busy[scmd_id(cmd)] & (1 << cmd->device->lun))
-#endif
-			) {
-				list_del(&ncmd->list);
-				dsprintk(NDEBUG_QUEUES, instance,
-				         "dequeue: removed %p from issue queue\n", cmd);
-				return cmd;
-			}
-		}
-	} else {
-		/* Autosense processing begins here */
-		ncmd = list_first_entry(&hostdata->autosense,
-		                        struct NCR5380_cmd, list);
-		list_del(&ncmd->list);
-		cmd = NCR5380_to_scmd(ncmd);
-		dsprintk(NDEBUG_QUEUES, instance,
-		         "dequeue: removed %p from autosense queue\n", cmd);
-		scsi_eh_prep_cmnd(cmd, &hostdata->ses, NULL, 0, ~0);
-		hostdata->sensing = cmd;
-		return cmd;
-	}
-	return NULL;
-}
-
-static void requeue_cmd(struct Scsi_Host *instance, struct scsi_cmnd *cmd)
-{
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-	struct NCR5380_cmd *ncmd = scsi_cmd_priv(cmd);
-
-	if (hostdata->sensing == cmd) {
-		scsi_eh_restore_cmnd(cmd, &hostdata->ses);
-		list_add(&ncmd->list, &hostdata->autosense);
-		hostdata->sensing = NULL;
-	} else
-		list_add(&ncmd->list, &hostdata->unissued);
-}
-
-/**
- * NCR5380_main - NCR state machines
- *
- * NCR5380_main is a coroutine that runs as long as more work can
- * be done on the NCR5380 host adapters in a system.  Both
- * NCR5380_queue_command() and NCR5380_intr() will try to start it
- * in case it is not running.
- */
-
-static void NCR5380_main(struct work_struct *work)
-{
-	struct NCR5380_hostdata *hostdata =
-		container_of(work, struct NCR5380_hostdata, main_task);
-	struct Scsi_Host *instance = hostdata->host;
-	int done;
-
-	/*
-	 * ++roman: Just disabling the NCR interrupt isn't sufficient here,
-	 * because also a timer int can trigger an abort or reset, which can
-	 * alter queues and touch the Falcon lock.
-	 */
-
-	do {
-		done = 1;
-
-		spin_lock_irq(&hostdata->lock);
-		while (!hostdata->connected && !hostdata->selecting) {
-			struct scsi_cmnd *cmd = dequeue_next_cmd(instance);
-
-			if (!cmd)
-				break;
-
-			dsprintk(NDEBUG_MAIN, instance, "main: dequeued %p\n", cmd);
-
-			/*
-			 * Attempt to establish an I_T_L nexus here.
-			 * On success, instance->hostdata->connected is set.
-			 * On failure, we must add the command back to the
-			 * issue queue so we can keep trying.
-			 */
-			/*
-			 * REQUEST SENSE commands are issued without tagged
-			 * queueing, even on SCSI-II devices because the
-			 * contingent allegiance condition exists for the
-			 * entire unit.
-			 */
-			/* ++roman: ...and the standard also requires that
-			 * REQUEST SENSE command are untagged.
-			 */
-
-#ifdef SUPPORT_TAGS
-			cmd_get_tag(cmd, cmd->cmnd[0] != REQUEST_SENSE);
-#endif
-			if (!NCR5380_select(instance, cmd)) {
-				dsprintk(NDEBUG_MAIN, instance, "main: select complete\n");
-				maybe_release_dma_irq(instance);
-			} else {
-				dsprintk(NDEBUG_MAIN | NDEBUG_QUEUES, instance,
-				         "main: select failed, returning %p to queue\n", cmd);
-				requeue_cmd(instance, cmd);
-#ifdef SUPPORT_TAGS
-				cmd_free_tag(cmd);
-#endif
-			}
-		}
-		if (hostdata->connected && !hostdata->dma_len) {
-			dsprintk(NDEBUG_MAIN, instance, "main: performing information transfer\n");
-			NCR5380_information_transfer(instance);
-			done = 0;
-		}
-		spin_unlock_irq(&hostdata->lock);
-		if (!done)
-			cond_resched();
-	} while (!done);
-}
-
-
-/*
- * Function : void NCR5380_dma_complete (struct Scsi_Host *instance)
- *
- * Purpose : Called by interrupt handler when DMA finishes or a phase
- * mismatch occurs (which would finish the DMA transfer).
- *
- * Inputs : instance - this instance of the NCR5380.
- */
-
-static void NCR5380_dma_complete(struct Scsi_Host *instance)
-{
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-	int transferred;
-	unsigned char **data;
-	int *count;
-	int saved_data = 0, overrun = 0;
-	unsigned char p;
-
-	if (hostdata->read_overruns) {
-		p = hostdata->connected->SCp.phase;
-		if (p & SR_IO) {
-			udelay(10);
-			if ((NCR5380_read(BUS_AND_STATUS_REG) &
-			     (BASR_PHASE_MATCH|BASR_ACK)) ==
-			    (BASR_PHASE_MATCH|BASR_ACK)) {
-				saved_data = NCR5380_read(INPUT_DATA_REG);
-				overrun = 1;
-				dsprintk(NDEBUG_DMA, instance, "read overrun handled\n");
-			}
-		}
-	}
-
-#if defined(CONFIG_SUN3)
-	if ((sun3scsi_dma_finish(rq_data_dir(hostdata->connected->request)))) {
-		pr_err("scsi%d: overrun in UDC counter -- not prepared to deal with this!\n",
-		       instance->host_no);
-		BUG();
-	}
-
-	/* make sure we're not stuck in a data phase */
-	if ((NCR5380_read(BUS_AND_STATUS_REG) & (BASR_PHASE_MATCH | BASR_ACK)) ==
-	    (BASR_PHASE_MATCH | BASR_ACK)) {
-		pr_err("scsi%d: BASR %02x\n", instance->host_no,
-		       NCR5380_read(BUS_AND_STATUS_REG));
-		pr_err("scsi%d: bus stuck in data phase -- probably a single byte overrun!\n",
-		       instance->host_no);
-		BUG();
-	}
-#endif
-
-	NCR5380_write(MODE_REG, MR_BASE);
-	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-	NCR5380_read(RESET_PARITY_INTERRUPT_REG);
-
-	transferred = hostdata->dma_len - NCR5380_dma_residual(instance);
-	hostdata->dma_len = 0;
-
-	data = (unsigned char **)&hostdata->connected->SCp.ptr;
-	count = &hostdata->connected->SCp.this_residual;
-	*data += transferred;
-	*count -= transferred;
-
-	if (hostdata->read_overruns) {
-		int cnt, toPIO;
-
-		if ((NCR5380_read(STATUS_REG) & PHASE_MASK) == p && (p & SR_IO)) {
-			cnt = toPIO = hostdata->read_overruns;
-			if (overrun) {
-				dprintk(NDEBUG_DMA, "Got an input overrun, using saved byte\n");
-				*(*data)++ = saved_data;
-				(*count)--;
-				cnt--;
-				toPIO--;
-			}
-			dprintk(NDEBUG_DMA, "Doing %d-byte PIO to 0x%08lx\n", cnt, (long)*data);
-			NCR5380_transfer_pio(instance, &p, &cnt, data);
-			*count -= toPIO - cnt;
-		}
-	}
-}
-
-
-/**
- * NCR5380_intr - generic NCR5380 irq handler
- * @irq: interrupt number
- * @dev_id: device info
- *
- * Handle interrupts, reestablishing I_T_L or I_T_L_Q nexuses
- * from the disconnected queue, and restarting NCR5380_main()
- * as required.
- *
- * The chip can assert IRQ in any of six different conditions. The IRQ flag
- * is then cleared by reading the Reset Parity/Interrupt Register (RPIR).
- * Three of these six conditions are latched in the Bus and Status Register:
- * - End of DMA (cleared by ending DMA Mode)
- * - Parity error (cleared by reading RPIR)
- * - Loss of BSY (cleared by reading RPIR)
- * Two conditions have flag bits that are not latched:
- * - Bus phase mismatch (non-maskable in DMA Mode, cleared by ending DMA Mode)
- * - Bus reset (non-maskable)
- * The remaining condition has no flag bit at all:
- * - Selection/reselection
- *
- * Hence, establishing the cause(s) of any interrupt is partly guesswork.
- * In "The DP8490 and DP5380 Comparison Guide", National Semiconductor
- * claimed that "the design of the [DP8490] interrupt logic ensures
- * interrupts will not be lost (they can be on the DP5380)."
- * The L5380/53C80 datasheet from LOGIC Devices has more details.
- *
- * Checking for bus reset by reading RST is futile because of interrupt
- * latency, but a bus reset will reset chip logic. Checking for parity error
- * is unnecessary because that interrupt is never enabled. A Loss of BSY
- * condition will clear DMA Mode. We can tell when this occurs because the
- * the Busy Monitor interrupt is enabled together with DMA Mode.
- */
-
-static irqreturn_t NCR5380_intr(int irq, void *dev_id)
-{
-	struct Scsi_Host *instance = dev_id;
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-	int handled = 0;
-	unsigned char basr;
-	unsigned long flags;
-
-	spin_lock_irqsave(&hostdata->lock, flags);
-
-	basr = NCR5380_read(BUS_AND_STATUS_REG);
-	if (basr & BASR_IRQ) {
-		unsigned char mr = NCR5380_read(MODE_REG);
-		unsigned char sr = NCR5380_read(STATUS_REG);
-
-		dsprintk(NDEBUG_INTR, instance, "IRQ %d, BASR 0x%02x, SR 0x%02x, MR 0x%02x\n",
-		         irq, basr, sr, mr);
-
-		if ((mr & MR_DMA_MODE) || (mr & MR_MONITOR_BSY)) {
-			/* Probably End of DMA, Phase Mismatch or Loss of BSY.
-			 * We ack IRQ after clearing Mode Register. Workarounds
-			 * for End of DMA errata need to happen in DMA Mode.
-			 */
-
-			dsprintk(NDEBUG_INTR, instance, "interrupt in DMA mode\n");
-
-			if (hostdata->connected) {
-				NCR5380_dma_complete(instance);
-				queue_work(hostdata->work_q, &hostdata->main_task);
-			} else {
-				NCR5380_write(MODE_REG, MR_BASE);
-				NCR5380_read(RESET_PARITY_INTERRUPT_REG);
-			}
-		} else if ((NCR5380_read(CURRENT_SCSI_DATA_REG) & hostdata->id_mask) &&
-		    (sr & (SR_SEL | SR_IO | SR_BSY | SR_RST)) == (SR_SEL | SR_IO)) {
-			/* Probably reselected */
-			NCR5380_write(SELECT_ENABLE_REG, 0);
-			NCR5380_read(RESET_PARITY_INTERRUPT_REG);
-
-			dsprintk(NDEBUG_INTR, instance, "interrupt with SEL and IO\n");
-
-			if (!hostdata->connected) {
-				NCR5380_reselect(instance);
-				queue_work(hostdata->work_q, &hostdata->main_task);
-			}
-			if (!hostdata->connected)
-				NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
-		} else {
-			/* Probably Bus Reset */
-			NCR5380_read(RESET_PARITY_INTERRUPT_REG);
-
-			dsprintk(NDEBUG_INTR, instance, "unknown interrupt\n");
-#ifdef SUN3_SCSI_VME
-			dregs->csr |= CSR_DMA_ENABLE;
-#endif
-		}
-		handled = 1;
-	} else {
-		shost_printk(KERN_NOTICE, instance, "interrupt without IRQ bit\n");
-#ifdef SUN3_SCSI_VME
-		dregs->csr |= CSR_DMA_ENABLE;
-#endif
-	}
-
-	spin_unlock_irqrestore(&hostdata->lock, flags);
-
-	return IRQ_RETVAL(handled);
-}
-
-/*
- * Function : int NCR5380_select(struct Scsi_Host *instance,
- * struct scsi_cmnd *cmd)
- *
- * Purpose : establishes I_T_L or I_T_L_Q nexus for new or existing command,
- * including ARBITRATION, SELECTION, and initial message out for
- * IDENTIFY and queue messages.
- *
- * Inputs : instance - instantiation of the 5380 driver on which this
- * target lives, cmd - SCSI command to execute.
- *
- * Returns cmd if selection failed but should be retried,
- * NULL if selection failed and should not be retried, or
- * NULL if selection succeeded (hostdata->connected == cmd).
- *
- * Side effects :
- * If bus busy, arbitration failed, etc, NCR5380_select() will exit
- * with registers as they should have been on entry - ie
- * SELECT_ENABLE will be set appropriately, the NCR5380
- * will cease to drive any SCSI bus signals.
- *
- * If successful : I_T_L or I_T_L_Q nexus will be established,
- * instance->connected will be set to cmd.
- * SELECT interrupt will be disabled.
- *
- * If failed (no target) : cmd->scsi_done() will be called, and the
- * cmd->result host byte set to DID_BAD_TARGET.
- */
-
-static struct scsi_cmnd *NCR5380_select(struct Scsi_Host *instance,
-                                        struct scsi_cmnd *cmd)
-{
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-	unsigned char tmp[3], phase;
-	unsigned char *data;
-	int len;
-	int err;
-
-	NCR5380_dprint(NDEBUG_ARBITRATION, instance);
-	dsprintk(NDEBUG_ARBITRATION, instance, "starting arbitration, id = %d\n",
-	         instance->this_id);
-
-	/*
-	 * Arbitration and selection phases are slow and involve dropping the
-	 * lock, so we have to watch out for EH. An exception handler may
-	 * change 'selecting' to NULL. This function will then return NULL
-	 * so that the caller will forget about 'cmd'. (During information
-	 * transfer phases, EH may change 'connected' to NULL.)
-	 */
-	hostdata->selecting = cmd;
-
-	/*
-	 * Set the phase bits to 0, otherwise the NCR5380 won't drive the
-	 * data bus during SELECTION.
-	 */
-
-	NCR5380_write(TARGET_COMMAND_REG, 0);
-
-	/*
-	 * Start arbitration.
-	 */
-
-	NCR5380_write(OUTPUT_DATA_REG, hostdata->id_mask);
-	NCR5380_write(MODE_REG, MR_ARBITRATE);
-
-	/* The chip now waits for BUS FREE phase. Then after the 800 ns
-	 * Bus Free Delay, arbitration will begin.
-	 */
-
-	spin_unlock_irq(&hostdata->lock);
-	err = NCR5380_poll_politely2(instance, MODE_REG, MR_ARBITRATE, 0,
-	                INITIATOR_COMMAND_REG, ICR_ARBITRATION_PROGRESS,
-	                                       ICR_ARBITRATION_PROGRESS, HZ);
-	spin_lock_irq(&hostdata->lock);
-	if (!(NCR5380_read(MODE_REG) & MR_ARBITRATE)) {
-		/* Reselection interrupt */
-		goto out;
-	}
-	if (!hostdata->selecting) {
-		/* Command was aborted */
-		NCR5380_write(MODE_REG, MR_BASE);
-		goto out;
-	}
-	if (err < 0) {
-		NCR5380_write(MODE_REG, MR_BASE);
-		shost_printk(KERN_ERR, instance,
-		             "select: arbitration timeout\n");
-		goto out;
-	}
-	spin_unlock_irq(&hostdata->lock);
-
-	/* The SCSI-2 arbitration delay is 2.4 us */
-	udelay(3);
-
-	/* Check for lost arbitration */
-	if ((NCR5380_read(INITIATOR_COMMAND_REG) & ICR_ARBITRATION_LOST) ||
-	    (NCR5380_read(CURRENT_SCSI_DATA_REG) & hostdata->id_higher_mask) ||
-	    (NCR5380_read(INITIATOR_COMMAND_REG) & ICR_ARBITRATION_LOST)) {
-		NCR5380_write(MODE_REG, MR_BASE);
-		dsprintk(NDEBUG_ARBITRATION, instance, "lost arbitration, deasserting MR_ARBITRATE\n");
-		spin_lock_irq(&hostdata->lock);
-		goto out;
-	}
-
-	/* After/during arbitration, BSY should be asserted.
-	 * IBM DPES-31080 Version S31Q works now
-	 * Tnx to Thomas_Roesch@m2.maus.de for finding this! (Roman)
-	 */
-	NCR5380_write(INITIATOR_COMMAND_REG,
-		      ICR_BASE | ICR_ASSERT_SEL | ICR_ASSERT_BSY);
-
-	/*
-	 * Again, bus clear + bus settle time is 1.2us, however, this is
-	 * a minimum so we'll udelay ceil(1.2)
-	 */
-
-	if (hostdata->flags & FLAG_TOSHIBA_DELAY)
-		udelay(15);
-	else
-		udelay(2);
-
-	spin_lock_irq(&hostdata->lock);
-
-	/* NCR5380_reselect() clears MODE_REG after a reselection interrupt */
-	if (!(NCR5380_read(MODE_REG) & MR_ARBITRATE))
-		goto out;
-
-	if (!hostdata->selecting) {
-		NCR5380_write(MODE_REG, MR_BASE);
-		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-		goto out;
-	}
-
-	dsprintk(NDEBUG_ARBITRATION, instance, "won arbitration\n");
-
-	/*
-	 * Now that we have won arbitration, start Selection process, asserting
-	 * the host and target ID's on the SCSI bus.
-	 */
-
-	NCR5380_write(OUTPUT_DATA_REG, hostdata->id_mask | (1 << scmd_id(cmd)));
-
-	/*
-	 * Raise ATN while SEL is true before BSY goes false from arbitration,
-	 * since this is the only way to guarantee that we'll get a MESSAGE OUT
-	 * phase immediately after selection.
-	 */
-
-	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_BSY |
-	              ICR_ASSERT_DATA | ICR_ASSERT_ATN | ICR_ASSERT_SEL);
-	NCR5380_write(MODE_REG, MR_BASE);
-
-	/*
-	 * Reselect interrupts must be turned off prior to the dropping of BSY,
-	 * otherwise we will trigger an interrupt.
-	 */
-	NCR5380_write(SELECT_ENABLE_REG, 0);
-
-	spin_unlock_irq(&hostdata->lock);
-
-	/*
-	 * The initiator shall then wait at least two deskew delays and release
-	 * the BSY signal.
-	 */
-	udelay(1);        /* wingel -- wait two bus deskew delay >2*45ns */
-
-	/* Reset BSY */
-	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA |
-	              ICR_ASSERT_ATN | ICR_ASSERT_SEL);
-
-	/*
-	 * Something weird happens when we cease to drive BSY - looks
-	 * like the board/chip is letting us do another read before the
-	 * appropriate propagation delay has expired, and we're confusing
-	 * a BSY signal from ourselves as the target's response to SELECTION.
-	 *
-	 * A small delay (the 'C++' frontend breaks the pipeline with an
-	 * unnecessary jump, making it work on my 386-33/Trantor T128, the
-	 * tighter 'C' code breaks and requires this) solves the problem -
-	 * the 1 us delay is arbitrary, and only used because this delay will
-	 * be the same on other platforms and since it works here, it should
-	 * work there.
-	 *
-	 * wingel suggests that this could be due to failing to wait
-	 * one deskew delay.
-	 */
-
-	udelay(1);
-
-	dsprintk(NDEBUG_SELECTION, instance, "selecting target %d\n", scmd_id(cmd));
-
-	/*
-	 * The SCSI specification calls for a 250 ms timeout for the actual
-	 * selection.
-	 */
-
-	err = NCR5380_poll_politely(instance, STATUS_REG, SR_BSY, SR_BSY,
-	                            msecs_to_jiffies(250));
-
-	if ((NCR5380_read(STATUS_REG) & (SR_SEL | SR_IO)) == (SR_SEL | SR_IO)) {
-		spin_lock_irq(&hostdata->lock);
-		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-		NCR5380_reselect(instance);
-		if (!hostdata->connected)
-			NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
-		shost_printk(KERN_ERR, instance, "reselection after won arbitration?\n");
-		goto out;
-	}
-
-	if (err < 0) {
-		spin_lock_irq(&hostdata->lock);
-		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-		NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
-		/* Can't touch cmd if it has been reclaimed by the scsi ML */
-		if (hostdata->selecting) {
-			cmd->result = DID_BAD_TARGET << 16;
-			complete_cmd(instance, cmd);
-			dsprintk(NDEBUG_SELECTION, instance, "target did not respond within 250ms\n");
-			cmd = NULL;
-		}
-		goto out;
-	}
-
-	/*
-	 * No less than two deskew delays after the initiator detects the
-	 * BSY signal is true, it shall release the SEL signal and may
-	 * change the DATA BUS.                                     -wingel
-	 */
-
-	udelay(1);
-
-	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
-
-	/*
-	 * Since we followed the SCSI spec, and raised ATN while SEL
-	 * was true but before BSY was false during selection, the information
-	 * transfer phase should be a MESSAGE OUT phase so that we can send the
-	 * IDENTIFY message.
-	 *
-	 * If SCSI-II tagged queuing is enabled, we also send a SIMPLE_QUEUE_TAG
-	 * message (2 bytes) with a tag ID that we increment with every command
-	 * until it wraps back to 0.
-	 *
-	 * XXX - it turns out that there are some broken SCSI-II devices,
-	 * which claim to support tagged queuing but fail when more than
-	 * some number of commands are issued at once.
-	 */
-
-	/* Wait for start of REQ/ACK handshake */
-
-	err = NCR5380_poll_politely(instance, STATUS_REG, SR_REQ, SR_REQ, HZ);
-	spin_lock_irq(&hostdata->lock);
-	if (err < 0) {
-		shost_printk(KERN_ERR, instance, "select: REQ timeout\n");
-		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-		NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
-		goto out;
-	}
-	if (!hostdata->selecting) {
-		do_abort(instance);
-		goto out;
-	}
-
-	dsprintk(NDEBUG_SELECTION, instance, "target %d selected, going into MESSAGE OUT phase.\n",
-	         scmd_id(cmd));
-	tmp[0] = IDENTIFY(1, cmd->device->lun);
-
-#ifdef SUPPORT_TAGS
-	if (cmd->tag != TAG_NONE) {
-		tmp[1] = hostdata->last_message = SIMPLE_QUEUE_TAG;
-		tmp[2] = cmd->tag;
-		len = 3;
-	} else
-		len = 1;
-#else
-	len = 1;
-	cmd->tag = 0;
-#endif /* SUPPORT_TAGS */
-
-	/* Send message(s) */
-	data = tmp;
-	phase = PHASE_MSGOUT;
-	NCR5380_transfer_pio(instance, &phase, &len, &data);
-	dsprintk(NDEBUG_SELECTION, instance, "nexus established.\n");
-	/* XXX need to handle errors here */
-
-	hostdata->connected = cmd;
-#ifndef SUPPORT_TAGS
-	hostdata->busy[cmd->device->id] |= 1 << cmd->device->lun;
-#endif
-#ifdef SUN3_SCSI_VME
-	dregs->csr |= CSR_INTR;
-#endif
-
-	initialize_SCp(cmd);
-
-	cmd = NULL;
-
-out:
-	if (!hostdata->selecting)
-		return NULL;
-	hostdata->selecting = NULL;
-	return cmd;
-}
-
-/*
- * Function : int NCR5380_transfer_pio (struct Scsi_Host *instance,
- * unsigned char *phase, int *count, unsigned char **data)
- *
- * Purpose : transfers data in given phase using polled I/O
- *
- * Inputs : instance - instance of driver, *phase - pointer to
- * what phase is expected, *count - pointer to number of
- * bytes to transfer, **data - pointer to data pointer.
- *
- * Returns : -1 when different phase is entered without transferring
- * maximum number of bytes, 0 if all bytes are transferred or exit
- * is in same phase.
- *
- * Also, *phase, *count, *data are modified in place.
- *
- * XXX Note : handling for bus free may be useful.
- */
-
-/*
- * Note : this code is not as quick as it could be, however it
- * IS 100% reliable, and for the actual data transfer where speed
- * counts, we will always do a pseudo DMA or DMA transfer.
- */
-
-static int NCR5380_transfer_pio(struct Scsi_Host *instance,
-				unsigned char *phase, int *count,
-				unsigned char **data)
-{
-	unsigned char p = *phase, tmp;
-	int c = *count;
-	unsigned char *d = *data;
-
-	/*
-	 * The NCR5380 chip will only drive the SCSI bus when the
-	 * phase specified in the appropriate bits of the TARGET COMMAND
-	 * REGISTER match the STATUS REGISTER
-	 */
-
-	NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p));
-
-	do {
-		/*
-		 * Wait for assertion of REQ, after which the phase bits will be
-		 * valid
-		 */
-
-		if (NCR5380_poll_politely(instance, STATUS_REG, SR_REQ, SR_REQ, HZ) < 0)
-			break;
-
-		dsprintk(NDEBUG_HANDSHAKE, instance, "REQ asserted\n");
-
-		/* Check for phase mismatch */
-		if ((NCR5380_read(STATUS_REG) & PHASE_MASK) != p) {
-			dsprintk(NDEBUG_PIO, instance, "phase mismatch\n");
-			NCR5380_dprint_phase(NDEBUG_PIO, instance);
-			break;
-		}
-
-		/* Do actual transfer from SCSI bus to / from memory */
-		if (!(p & SR_IO))
-			NCR5380_write(OUTPUT_DATA_REG, *d);
-		else
-			*d = NCR5380_read(CURRENT_SCSI_DATA_REG);
-
-		++d;
-
-		/*
-		 * The SCSI standard suggests that in MSGOUT phase, the initiator
-		 * should drop ATN on the last byte of the message phase
-		 * after REQ has been asserted for the handshake but before
-		 * the initiator raises ACK.
-		 */
-
-		if (!(p & SR_IO)) {
-			if (!((p & SR_MSG) && c > 1)) {
-				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA);
-				NCR5380_dprint(NDEBUG_PIO, instance);
-				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
-				              ICR_ASSERT_DATA | ICR_ASSERT_ACK);
-			} else {
-				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
-				              ICR_ASSERT_DATA | ICR_ASSERT_ATN);
-				NCR5380_dprint(NDEBUG_PIO, instance);
-				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
-				              ICR_ASSERT_DATA | ICR_ASSERT_ATN | ICR_ASSERT_ACK);
-			}
-		} else {
-			NCR5380_dprint(NDEBUG_PIO, instance);
-			NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ACK);
-		}
-
-		if (NCR5380_poll_politely(instance,
-		                          STATUS_REG, SR_REQ, 0, 5 * HZ) < 0)
-			break;
-
-		dsprintk(NDEBUG_HANDSHAKE, instance, "REQ negated, handshake complete\n");
-
-/*
- * We have several special cases to consider during REQ/ACK handshaking :
- * 1.  We were in MSGOUT phase, and we are on the last byte of the
- * message.  ATN must be dropped as ACK is dropped.
- *
- * 2.  We are in a MSGIN phase, and we are on the last byte of the
- * message.  We must exit with ACK asserted, so that the calling
- * code may raise ATN before dropping ACK to reject the message.
- *
- * 3.  ACK and ATN are clear and the target may proceed as normal.
- */
-		if (!(p == PHASE_MSGIN && c == 1)) {
-			if (p == PHASE_MSGOUT && c > 1)
-				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
-			else
-				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-		}
-	} while (--c);
-
-	dsprintk(NDEBUG_PIO, instance, "residual %d\n", c);
-
-	*count = c;
-	*data = d;
-	tmp = NCR5380_read(STATUS_REG);
-	/* The phase read from the bus is valid if either REQ is (already)
-	 * asserted or if ACK hasn't been released yet. The latter applies if
-	 * we're in MSG IN, DATA IN or STATUS and all bytes have been received.
-	 */
-	if ((tmp & SR_REQ) || ((tmp & SR_IO) && c == 0))
-		*phase = tmp & PHASE_MASK;
-	else
-		*phase = PHASE_UNKNOWN;
-
-	if (!c || (*phase == p))
-		return 0;
-	else
-		return -1;
-}
-
-/**
- * do_reset - issue a reset command
- * @instance: adapter to reset
- *
- * Issue a reset sequence to the NCR5380 and try and get the bus
- * back into sane shape.
- *
- * This clears the reset interrupt flag because there may be no handler for
- * it. When the driver is initialized, the NCR5380_intr() handler has not yet
- * been installed. And when in EH we may have released the ST DMA interrupt.
- */
-
-static void do_reset(struct Scsi_Host *instance)
-{
-	unsigned long flags;
-
-	local_irq_save(flags);
-	NCR5380_write(TARGET_COMMAND_REG,
-	              PHASE_SR_TO_TCR(NCR5380_read(STATUS_REG) & PHASE_MASK));
-	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_RST);
-	udelay(50);
-	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-	(void)NCR5380_read(RESET_PARITY_INTERRUPT_REG);
-	local_irq_restore(flags);
-}
-
-/**
- * do_abort - abort the currently established nexus by going to
- * MESSAGE OUT phase and sending an ABORT message.
- * @instance: relevant scsi host instance
- *
- * Returns 0 on success, -1 on failure.
- */
-
-static int do_abort(struct Scsi_Host *instance)
-{
-	unsigned char *msgptr, phase, tmp;
-	int len;
-	int rc;
-
-	/* Request message out phase */
-	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
-
-	/*
-	 * Wait for the target to indicate a valid phase by asserting
-	 * REQ.  Once this happens, we'll have either a MSGOUT phase
-	 * and can immediately send the ABORT message, or we'll have some
-	 * other phase and will have to source/sink data.
-	 *
-	 * We really don't care what value was on the bus or what value
-	 * the target sees, so we just handshake.
-	 */
-
-	rc = NCR5380_poll_politely(instance, STATUS_REG, SR_REQ, SR_REQ, 10 * HZ);
-	if (rc < 0)
-		goto timeout;
-
-	tmp = NCR5380_read(STATUS_REG) & PHASE_MASK;
-
-	NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(tmp));
-
-	if (tmp != PHASE_MSGOUT) {
-		NCR5380_write(INITIATOR_COMMAND_REG,
-		              ICR_BASE | ICR_ASSERT_ATN | ICR_ASSERT_ACK);
-		rc = NCR5380_poll_politely(instance, STATUS_REG, SR_REQ, 0, 3 * HZ);
-		if (rc < 0)
-			goto timeout;
-		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
-	}
-
-	tmp = ABORT;
-	msgptr = &tmp;
-	len = 1;
-	phase = PHASE_MSGOUT;
-	NCR5380_transfer_pio(instance, &phase, &len, &msgptr);
-
-	/*
-	 * If we got here, and the command completed successfully,
-	 * we're about to go into bus free state.
-	 */
-
-	return len ? -1 : 0;
-
-timeout:
-	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-	return -1;
-}
-
-
-/*
- * Function : int NCR5380_transfer_dma (struct Scsi_Host *instance,
- * unsigned char *phase, int *count, unsigned char **data)
- *
- * Purpose : transfers data in given phase using either real
- * or pseudo DMA.
- *
- * Inputs : instance - instance of driver, *phase - pointer to
- * what phase is expected, *count - pointer to number of
- * bytes to transfer, **data - pointer to data pointer.
- *
- * Returns : -1 when different phase is entered without transferring
- * maximum number of bytes, 0 if all bytes or transferred or exit
- * is in same phase.
- *
- * Also, *phase, *count, *data are modified in place.
- */
-
-
-static int NCR5380_transfer_dma(struct Scsi_Host *instance,
-				unsigned char *phase, int *count,
-				unsigned char **data)
-{
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-	register int c = *count;
-	register unsigned char p = *phase;
-
-#if defined(CONFIG_SUN3)
-	/* sanity check */
-	if (!sun3_dma_setup_done) {
-		pr_err("scsi%d: transfer_dma without setup!\n",
-		       instance->host_no);
-		BUG();
-	}
-	hostdata->dma_len = c;
-
-	dsprintk(NDEBUG_DMA, instance, "initializing DMA %s: length %d, address %p\n",
-	         (p & SR_IO) ? "receive" : "send", c, *data);
-
-	/* netbsd turns off ints here, why not be safe and do it too */
-
-	/* send start chain */
-	sun3scsi_dma_start(c, *data);
-
-	NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p));
-	NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY |
-	                        MR_ENABLE_EOP_INTR);
-	if (p & SR_IO) {
-		NCR5380_write(INITIATOR_COMMAND_REG, 0);
-		NCR5380_write(START_DMA_INITIATOR_RECEIVE_REG, 0);
-	} else {
-		NCR5380_write(INITIATOR_COMMAND_REG, ICR_ASSERT_DATA);
-		NCR5380_write(START_DMA_SEND_REG, 0);
-	}
-
-#ifdef SUN3_SCSI_VME
-	dregs->csr |= CSR_DMA_ENABLE;
-#endif
-
-	sun3_dma_active = 1;
-
-#else /* !defined(CONFIG_SUN3) */
-	register unsigned char *d = *data;
-	unsigned char tmp;
-
-	if ((tmp = (NCR5380_read(STATUS_REG) & PHASE_MASK)) != p) {
-		*phase = tmp;
-		return -1;
-	}
-
-	if (hostdata->read_overruns && (p & SR_IO))
-		c -= hostdata->read_overruns;
-
-	dsprintk(NDEBUG_DMA, instance, "initializing DMA %s: length %d, address %p\n",
-	         (p & SR_IO) ? "receive" : "send", c, d);
-
-	NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p));
-	NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY |
-	                        MR_ENABLE_EOP_INTR);
-
-	if (!(hostdata->flags & FLAG_LATE_DMA_SETUP)) {
-		/* On the Medusa, it is a must to initialize the DMA before
-		 * starting the NCR. This is also the cleaner way for the TT.
-		 */
-		hostdata->dma_len = (p & SR_IO) ?
-			NCR5380_dma_read_setup(instance, d, c) :
-			NCR5380_dma_write_setup(instance, d, c);
-	}
-
-	if (p & SR_IO)
-		NCR5380_write(START_DMA_INITIATOR_RECEIVE_REG, 0);
-	else {
-		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA);
-		NCR5380_write(START_DMA_SEND_REG, 0);
-	}
-
-	if (hostdata->flags & FLAG_LATE_DMA_SETUP) {
-		/* On the Falcon, the DMA setup must be done after the last */
-		/* NCR access, else the DMA setup gets trashed!
-		 */
-		hostdata->dma_len = (p & SR_IO) ?
-			NCR5380_dma_read_setup(instance, d, c) :
-			NCR5380_dma_write_setup(instance, d, c);
-	}
-#endif /* !defined(CONFIG_SUN3) */
-
-	return 0;
-}
-
-/*
- * Function : NCR5380_information_transfer (struct Scsi_Host *instance)
- *
- * Purpose : run through the various SCSI phases and do as the target
- * directs us to.  Operates on the currently connected command,
- * instance->connected.
- *
- * Inputs : instance, instance for which we are doing commands
- *
- * Side effects : SCSI things happen, the disconnected queue will be
- * modified if a command disconnects, *instance->connected will
- * change.
- *
- * XXX Note : we need to watch for bus free or a reset condition here
- * to recover from an unexpected bus free condition.
- */
-
-static void NCR5380_information_transfer(struct Scsi_Host *instance)
-{
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-	unsigned char msgout = NOP;
-	int sink = 0;
-	int len;
-	int transfersize;
-	unsigned char *data;
-	unsigned char phase, tmp, extended_msg[10], old_phase = 0xff;
-	struct scsi_cmnd *cmd;
-
-#ifdef SUN3_SCSI_VME
-	dregs->csr |= CSR_INTR;
-#endif
-
-	while ((cmd = hostdata->connected)) {
-		struct NCR5380_cmd *ncmd = scsi_cmd_priv(cmd);
-
-		tmp = NCR5380_read(STATUS_REG);
-		/* We only have a valid SCSI phase when REQ is asserted */
-		if (tmp & SR_REQ) {
-			phase = (tmp & PHASE_MASK);
-			if (phase != old_phase) {
-				old_phase = phase;
-				NCR5380_dprint_phase(NDEBUG_INFORMATION, instance);
-			}
-#if defined(CONFIG_SUN3)
-			if (phase == PHASE_CMDOUT) {
-				void *d;
-				unsigned long count;
-
-				if (!cmd->SCp.this_residual && cmd->SCp.buffers_residual) {
-					count = cmd->SCp.buffer->length;
-					d = sg_virt(cmd->SCp.buffer);
-				} else {
-					count = cmd->SCp.this_residual;
-					d = cmd->SCp.ptr;
-				}
-				/* this command setup for dma yet? */
-				if (sun3_dma_setup_done != cmd &&
-				    sun3scsi_dma_xfer_len(count, cmd) > 0) {
-					sun3scsi_dma_setup(instance, d, count,
-					                   rq_data_dir(cmd->request));
-					sun3_dma_setup_done = cmd;
-				}
-#ifdef SUN3_SCSI_VME
-				dregs->csr |= CSR_INTR;
-#endif
-			}
-#endif /* CONFIG_SUN3 */
-
-			if (sink && (phase != PHASE_MSGOUT)) {
-				NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(tmp));
-
-				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN |
-				              ICR_ASSERT_ACK);
-				while (NCR5380_read(STATUS_REG) & SR_REQ)
-					;
-				NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
-				              ICR_ASSERT_ATN);
-				sink = 0;
-				continue;
-			}
-
-			switch (phase) {
-			case PHASE_DATAOUT:
-#if (NDEBUG & NDEBUG_NO_DATAOUT)
-				shost_printk(KERN_DEBUG, instance, "NDEBUG_NO_DATAOUT set, attempted DATAOUT aborted\n");
-				sink = 1;
-				do_abort(instance);
-				cmd->result = DID_ERROR << 16;
-				complete_cmd(instance, cmd);
-				hostdata->connected = NULL;
-				return;
-#endif
-			case PHASE_DATAIN:
-				/*
-				 * If there is no room left in the current buffer in the
-				 * scatter-gather list, move onto the next one.
-				 */
-
-				if (!cmd->SCp.this_residual && cmd->SCp.buffers_residual) {
-					++cmd->SCp.buffer;
-					--cmd->SCp.buffers_residual;
-					cmd->SCp.this_residual = cmd->SCp.buffer->length;
-					cmd->SCp.ptr = sg_virt(cmd->SCp.buffer);
-					merge_contiguous_buffers(cmd);
-					dsprintk(NDEBUG_INFORMATION, instance, "%d bytes and %d buffers left\n",
-					         cmd->SCp.this_residual,
-					         cmd->SCp.buffers_residual);
-				}
-
-				/*
-				 * The preferred transfer method is going to be
-				 * PSEUDO-DMA for systems that are strictly PIO,
-				 * since we can let the hardware do the handshaking.
-				 *
-				 * For this to work, we need to know the transfersize
-				 * ahead of time, since the pseudo-DMA code will sit
-				 * in an unconditional loop.
-				 */
-
-#if !defined(CONFIG_SUN3)
-				transfersize = 0;
-				if (!cmd->device->borken)
-#endif
-					transfersize = NCR5380_dma_xfer_len(instance, cmd, phase);
-
-				if (transfersize > 0) {
-					len = transfersize;
-					cmd->SCp.phase = phase;
-					if (NCR5380_transfer_dma(instance, &phase,
-					    &len, (unsigned char **)&cmd->SCp.ptr)) {
-						/*
-						 * If the watchdog timer fires, all future
-						 * accesses to this device will use the
-						 * polled-IO.
-						 */
-						scmd_printk(KERN_INFO, cmd,
-							"switching to slow handshake\n");
-						cmd->device->borken = 1;
-						sink = 1;
-						do_abort(instance);
-						cmd->result = DID_ERROR << 16;
-						/* XXX - need to source or sink data here, as appropriate */
-					} else
-						return;
-				} else {
-					/* Break up transfer into 3 ms chunks,
-					 * presuming 6 accesses per handshake.
-					 */
-					transfersize = min((unsigned long)cmd->SCp.this_residual,
-					                   hostdata->accesses_per_ms / 2);
-					len = transfersize;
-					NCR5380_transfer_pio(instance, &phase, &len,
-					                     (unsigned char **)&cmd->SCp.ptr);
-					cmd->SCp.this_residual -= transfersize - len;
-				}
-#if defined(CONFIG_SUN3)
-				/* if we had intended to dma that command clear it */
-				if (sun3_dma_setup_done == cmd)
-					sun3_dma_setup_done = NULL;
-#endif
-				return;
-			case PHASE_MSGIN:
-				len = 1;
-				data = &tmp;
-				NCR5380_transfer_pio(instance, &phase, &len, &data);
-				cmd->SCp.Message = tmp;
-
-				switch (tmp) {
-				case ABORT:
-				case COMMAND_COMPLETE:
-					/* Accept message by clearing ACK */
-					NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-					dsprintk(NDEBUG_QUEUES, instance,
-					         "COMMAND COMPLETE %p target %d lun %llu\n",
-					         cmd, scmd_id(cmd), cmd->device->lun);
-
-					hostdata->connected = NULL;
-#ifdef SUPPORT_TAGS
-					cmd_free_tag(cmd);
-					if (status_byte(cmd->SCp.Status) == QUEUE_FULL) {
-						u8 lun = cmd->device->lun;
-						struct tag_alloc *ta = &hostdata->TagAlloc[scmd_id(cmd)][lun];
-
-						dsprintk(NDEBUG_TAGS, instance,
-						         "QUEUE_FULL %p target %d lun %d nr_allocated %d\n",
-						         cmd, scmd_id(cmd), lun, ta->nr_allocated);
-						if (ta->queue_size > ta->nr_allocated)
-							ta->queue_size = ta->nr_allocated;
-					}
-#endif
-
-					cmd->result &= ~0xffff;
-					cmd->result |= cmd->SCp.Status;
-					cmd->result |= cmd->SCp.Message << 8;
-
-					if (cmd->cmnd[0] == REQUEST_SENSE)
-						complete_cmd(instance, cmd);
-					else {
-						if (cmd->SCp.Status == SAM_STAT_CHECK_CONDITION ||
-						    cmd->SCp.Status == SAM_STAT_COMMAND_TERMINATED) {
-							dsprintk(NDEBUG_QUEUES, instance, "autosense: adding cmd %p to tail of autosense queue\n",
-							         cmd);
-							list_add_tail(&ncmd->list,
-							              &hostdata->autosense);
-						} else
-							complete_cmd(instance, cmd);
-					}
-
-					/*
-					 * Restore phase bits to 0 so an interrupted selection,
-					 * arbitration can resume.
-					 */
-					NCR5380_write(TARGET_COMMAND_REG, 0);
-
-					/* Enable reselect interrupts */
-					NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
-
-					maybe_release_dma_irq(instance);
-					return;
-				case MESSAGE_REJECT:
-					/* Accept message by clearing ACK */
-					NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-					switch (hostdata->last_message) {
-					case HEAD_OF_QUEUE_TAG:
-					case ORDERED_QUEUE_TAG:
-					case SIMPLE_QUEUE_TAG:
-						/* The target obviously doesn't support tagged
-						 * queuing, even though it announced this ability in
-						 * its INQUIRY data ?!? (maybe only this LUN?) Ok,
-						 * clear 'tagged_supported' and lock the LUN, since
-						 * the command is treated as untagged further on.
-						 */
-						cmd->device->tagged_supported = 0;
-						hostdata->busy[cmd->device->id] |= (1 << cmd->device->lun);
-						cmd->tag = TAG_NONE;
-						dsprintk(NDEBUG_TAGS, instance, "target %d lun %llu rejected QUEUE_TAG message; tagged queuing disabled\n",
-						         scmd_id(cmd), cmd->device->lun);
-						break;
-					}
-					break;
-				case DISCONNECT:
-					/* Accept message by clearing ACK */
-					NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-					hostdata->connected = NULL;
-					list_add(&ncmd->list, &hostdata->disconnected);
-					dsprintk(NDEBUG_INFORMATION | NDEBUG_QUEUES,
-					         instance, "connected command %p for target %d lun %llu moved to disconnected queue\n",
-					         cmd, scmd_id(cmd), cmd->device->lun);
-
-					/*
-					 * Restore phase bits to 0 so an interrupted selection,
-					 * arbitration can resume.
-					 */
-					NCR5380_write(TARGET_COMMAND_REG, 0);
-
-					/* Enable reselect interrupts */
-					NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
-#ifdef SUN3_SCSI_VME
-					dregs->csr |= CSR_DMA_ENABLE;
-#endif
-					return;
-					/*
-					 * The SCSI data pointer is *IMPLICITLY* saved on a disconnect
-					 * operation, in violation of the SCSI spec so we can safely
-					 * ignore SAVE/RESTORE pointers calls.
-					 *
-					 * Unfortunately, some disks violate the SCSI spec and
-					 * don't issue the required SAVE_POINTERS message before
-					 * disconnecting, and we have to break spec to remain
-					 * compatible.
-					 */
-				case SAVE_POINTERS:
-				case RESTORE_POINTERS:
-					/* Accept message by clearing ACK */
-					NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-					break;
-				case EXTENDED_MESSAGE:
-					/*
-					 * Start the message buffer with the EXTENDED_MESSAGE
-					 * byte, since spi_print_msg() wants the whole thing.
-					 */
-					extended_msg[0] = EXTENDED_MESSAGE;
-					/* Accept first byte by clearing ACK */
-					NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-
-					spin_unlock_irq(&hostdata->lock);
-
-					dsprintk(NDEBUG_EXTENDED, instance, "receiving extended message\n");
-
-					len = 2;
-					data = extended_msg + 1;
-					phase = PHASE_MSGIN;
-					NCR5380_transfer_pio(instance, &phase, &len, &data);
-					dsprintk(NDEBUG_EXTENDED, instance, "length %d, code 0x%02x\n",
-					         (int)extended_msg[1],
-					         (int)extended_msg[2]);
-
-					if (!len && extended_msg[1] > 0 &&
-					    extended_msg[1] <= sizeof(extended_msg) - 2) {
-						/* Accept third byte by clearing ACK */
-						NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-						len = extended_msg[1] - 1;
-						data = extended_msg + 3;
-						phase = PHASE_MSGIN;
-
-						NCR5380_transfer_pio(instance, &phase, &len, &data);
-						dsprintk(NDEBUG_EXTENDED, instance, "message received, residual %d\n",
-						         len);
-
-						switch (extended_msg[2]) {
-						case EXTENDED_SDTR:
-						case EXTENDED_WDTR:
-						case EXTENDED_MODIFY_DATA_POINTER:
-						case EXTENDED_EXTENDED_IDENTIFY:
-							tmp = 0;
-						}
-					} else if (len) {
-						shost_printk(KERN_ERR, instance, "error receiving extended message\n");
-						tmp = 0;
-					} else {
-						shost_printk(KERN_NOTICE, instance, "extended message code %02x length %d is too long\n",
-						             extended_msg[2], extended_msg[1]);
-						tmp = 0;
-					}
-
-					spin_lock_irq(&hostdata->lock);
-					if (!hostdata->connected)
-						return;
-
-					/* Fall through to reject message */
-
-					/*
-					 * If we get something weird that we aren't expecting,
-					 * reject it.
-					 */
-				default:
-					if (!tmp) {
-						shost_printk(KERN_ERR, instance, "rejecting message ");
-						spi_print_msg(extended_msg);
-						printk("\n");
-					} else if (tmp != EXTENDED_MESSAGE)
-						scmd_printk(KERN_INFO, cmd,
-						            "rejecting unknown message %02x\n",
-						            tmp);
-					else
-						scmd_printk(KERN_INFO, cmd,
-						            "rejecting unknown extended message code %02x, length %d\n",
-						            extended_msg[1], extended_msg[0]);
-
-					msgout = MESSAGE_REJECT;
-					NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
-					break;
-				} /* switch (tmp) */
-				break;
-			case PHASE_MSGOUT:
-				len = 1;
-				data = &msgout;
-				hostdata->last_message = msgout;
-				NCR5380_transfer_pio(instance, &phase, &len, &data);
-				if (msgout == ABORT) {
-					hostdata->connected = NULL;
-					cmd->result = DID_ERROR << 16;
-					complete_cmd(instance, cmd);
-					maybe_release_dma_irq(instance);
-					NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
-					return;
-				}
-				msgout = NOP;
-				break;
-			case PHASE_CMDOUT:
-				len = cmd->cmd_len;
-				data = cmd->cmnd;
-				/*
-				 * XXX for performance reasons, on machines with a
-				 * PSEUDO-DMA architecture we should probably
-				 * use the dma transfer function.
-				 */
-				NCR5380_transfer_pio(instance, &phase, &len, &data);
-				break;
-			case PHASE_STATIN:
-				len = 1;
-				data = &tmp;
-				NCR5380_transfer_pio(instance, &phase, &len, &data);
-				cmd->SCp.Status = tmp;
-				break;
-			default:
-				shost_printk(KERN_ERR, instance, "unknown phase\n");
-				NCR5380_dprint(NDEBUG_ANY, instance);
-			} /* switch(phase) */
-		} else {
-			spin_unlock_irq(&hostdata->lock);
-			NCR5380_poll_politely(instance, STATUS_REG, SR_REQ, SR_REQ, HZ);
-			spin_lock_irq(&hostdata->lock);
-		}
-	}
-}
-
-/*
- * Function : void NCR5380_reselect (struct Scsi_Host *instance)
- *
- * Purpose : does reselection, initializing the instance->connected
- * field to point to the scsi_cmnd for which the I_T_L or I_T_L_Q
- * nexus has been reestablished,
- *
- * Inputs : instance - this instance of the NCR5380.
- */
-
-
-/* it might eventually prove necessary to do a dma setup on
-   reselection, but it doesn't seem to be needed now -- sam */
-
-static void NCR5380_reselect(struct Scsi_Host *instance)
-{
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-	unsigned char target_mask;
-	unsigned char lun;
-#ifdef SUPPORT_TAGS
-	unsigned char tag;
-#endif
-	unsigned char msg[3];
-	int __maybe_unused len;
-	unsigned char __maybe_unused *data, __maybe_unused phase;
-	struct NCR5380_cmd *ncmd;
-	struct scsi_cmnd *tmp;
-
-	/*
-	 * Disable arbitration, etc. since the host adapter obviously
-	 * lost, and tell an interrupted NCR5380_select() to restart.
-	 */
-
-	NCR5380_write(MODE_REG, MR_BASE);
-
-	target_mask = NCR5380_read(CURRENT_SCSI_DATA_REG) & ~(hostdata->id_mask);
-
-	dsprintk(NDEBUG_RESELECTION, instance, "reselect\n");
-
-	/*
-	 * At this point, we have detected that our SCSI ID is on the bus,
-	 * SEL is true and BSY was false for at least one bus settle delay
-	 * (400 ns).
-	 *
-	 * We must assert BSY ourselves, until the target drops the SEL
-	 * signal.
-	 */
-
-	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_BSY);
-	if (NCR5380_poll_politely(instance,
-	                          STATUS_REG, SR_SEL, 0, 2 * HZ) < 0) {
-		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-		return;
-	}
-	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-
-	/*
-	 * Wait for target to go into MSGIN.
-	 */
-
-	if (NCR5380_poll_politely(instance,
-	                          STATUS_REG, SR_REQ, SR_REQ, 2 * HZ) < 0) {
-		do_abort(instance);
-		return;
-	}
-
-#if defined(CONFIG_SUN3)
-	/* acknowledge toggle to MSGIN */
-	NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(PHASE_MSGIN));
-
-	/* peek at the byte without really hitting the bus */
-	msg[0] = NCR5380_read(CURRENT_SCSI_DATA_REG);
-#else
-	len = 1;
-	data = msg;
-	phase = PHASE_MSGIN;
-	NCR5380_transfer_pio(instance, &phase, &len, &data);
-
-	if (len) {
-		do_abort(instance);
-		return;
-	}
-#endif
-
-	if (!(msg[0] & 0x80)) {
-		shost_printk(KERN_ERR, instance, "expecting IDENTIFY message, got ");
-		spi_print_msg(msg);
-		printk("\n");
-		do_abort(instance);
-		return;
-	}
-	lun = msg[0] & 0x07;
-
-#if defined(SUPPORT_TAGS) && !defined(CONFIG_SUN3)
-	/* If the phase is still MSGIN, the target wants to send some more
-	 * messages. In case it supports tagged queuing, this is probably a
-	 * SIMPLE_QUEUE_TAG for the I_T_L_Q nexus.
-	 */
-	tag = TAG_NONE;
-	if (phase == PHASE_MSGIN && (hostdata->flags & FLAG_TAGGED_QUEUING)) {
-		/* Accept previous IDENTIFY message by clearing ACK */
-		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-		len = 2;
-		data = msg + 1;
-		if (!NCR5380_transfer_pio(instance, &phase, &len, &data) &&
-		    msg[1] == SIMPLE_QUEUE_TAG)
-			tag = msg[2];
-		dsprintk(NDEBUG_TAGS, instance, "reselect: target mask %02x, lun %d sent tag %d\n",
-		         target_mask, lun, tag);
-	}
-#endif
-
-	/*
-	 * Find the command corresponding to the I_T_L or I_T_L_Q  nexus we
-	 * just reestablished, and remove it from the disconnected queue.
-	 */
-
-	tmp = NULL;
-	list_for_each_entry(ncmd, &hostdata->disconnected, list) {
-		struct scsi_cmnd *cmd = NCR5380_to_scmd(ncmd);
-
-		if (target_mask == (1 << scmd_id(cmd)) &&
-		    lun == (u8)cmd->device->lun
-#ifdef SUPPORT_TAGS
-		    && (tag == cmd->tag)
-#endif
-		    ) {
-			list_del(&ncmd->list);
-			tmp = cmd;
-			break;
-		}
-	}
-
-	if (tmp) {
-		dsprintk(NDEBUG_RESELECTION | NDEBUG_QUEUES, instance,
-		         "reselect: removed %p from disconnected queue\n", tmp);
-	} else {
-
-#ifdef SUPPORT_TAGS
-		shost_printk(KERN_ERR, instance, "target bitmask 0x%02x lun %d tag %d not in disconnected queue.\n",
-		             target_mask, lun, tag);
-#else
-		shost_printk(KERN_ERR, instance, "target bitmask 0x%02x lun %d not in disconnected queue.\n",
-		             target_mask, lun);
-#endif
-		/*
-		 * Since we have an established nexus that we can't do anything
-		 * with, we must abort it.
-		 */
-		do_abort(instance);
-		return;
-	}
-
-#if defined(CONFIG_SUN3)
-	/* engage dma setup for the command we just saw */
-	{
-		void *d;
-		unsigned long count;
-
-		if (!tmp->SCp.this_residual && tmp->SCp.buffers_residual) {
-			count = tmp->SCp.buffer->length;
-			d = sg_virt(tmp->SCp.buffer);
-		} else {
-			count = tmp->SCp.this_residual;
-			d = tmp->SCp.ptr;
-		}
-		/* setup this command for dma if not already */
-		if (sun3_dma_setup_done != tmp &&
-		    sun3scsi_dma_xfer_len(count, tmp) > 0) {
-			sun3scsi_dma_setup(instance, d, count,
-			                   rq_data_dir(tmp->request));
-			sun3_dma_setup_done = tmp;
-		}
-	}
-
-	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ACK);
-#endif
-
-	/* Accept message by clearing ACK */
-	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-
-#if defined(SUPPORT_TAGS) && defined(CONFIG_SUN3)
-	/* If the phase is still MSGIN, the target wants to send some more
-	 * messages. In case it supports tagged queuing, this is probably a
-	 * SIMPLE_QUEUE_TAG for the I_T_L_Q nexus.
-	 */
-	tag = TAG_NONE;
-	if (phase == PHASE_MSGIN && setup_use_tagged_queuing) {
-		/* Accept previous IDENTIFY message by clearing ACK */
-		NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-		len = 2;
-		data = msg + 1;
-		if (!NCR5380_transfer_pio(instance, &phase, &len, &data) &&
-		    msg[1] == SIMPLE_QUEUE_TAG)
-			tag = msg[2];
-		dsprintk(NDEBUG_TAGS, instance, "reselect: target mask %02x, lun %d sent tag %d\n"
-		         target_mask, lun, tag);
-	}
-#endif
-
-	hostdata->connected = tmp;
-	dsprintk(NDEBUG_RESELECTION, instance, "nexus established, target %d, lun %llu, tag %d\n",
-	         scmd_id(tmp), tmp->device->lun, tmp->tag);
-}
-
-
-/**
- * list_find_cmd - test for presence of a command in a linked list
- * @haystack: list of commands
- * @needle: command to search for
- */
-
-static bool list_find_cmd(struct list_head *haystack,
-                          struct scsi_cmnd *needle)
-{
-	struct NCR5380_cmd *ncmd;
-
-	list_for_each_entry(ncmd, haystack, list)
-		if (NCR5380_to_scmd(ncmd) == needle)
-			return true;
-	return false;
-}
-
-/**
- * list_remove_cmd - remove a command from linked list
- * @haystack: list of commands
- * @needle: command to remove
- */
-
-static bool list_del_cmd(struct list_head *haystack,
-                         struct scsi_cmnd *needle)
-{
-	if (list_find_cmd(haystack, needle)) {
-		struct NCR5380_cmd *ncmd = scsi_cmd_priv(needle);
-
-		list_del(&ncmd->list);
-		return true;
-	}
-	return false;
-}
-
-/**
- * NCR5380_abort - scsi host eh_abort_handler() method
- * @cmd: the command to be aborted
- *
- * Try to abort a given command by removing it from queues and/or sending
- * the target an abort message. This may not succeed in causing a target
- * to abort the command. Nonetheless, the low-level driver must forget about
- * the command because the mid-layer reclaims it and it may be re-issued.
- *
- * The normal path taken by a command is as follows. For EH we trace this
- * same path to locate and abort the command.
- *
- * unissued -> selecting -> [unissued -> selecting ->]... connected ->
- * [disconnected -> connected ->]...
- * [autosense -> connected ->] done
- *
- * If cmd was not found at all then presumably it has already been completed,
- * in which case return SUCCESS to try to avoid further EH measures.
- *
- * If the command has not completed yet, we must not fail to find it.
- * We have no option but to forget the aborted command (even if it still
- * lacks sense data). The mid-layer may re-issue a command that is in error
- * recovery (see scsi_send_eh_cmnd), but the logic and data structures in
- * this driver are such that a command can appear on one queue only.
- *
- * The lock protects driver data structures, but EH handlers also use it
- * to serialize their own execution and prevent their own re-entry.
- */
-
-static int NCR5380_abort(struct scsi_cmnd *cmd)
-{
-	struct Scsi_Host *instance = cmd->device->host;
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-	unsigned long flags;
-	int result = SUCCESS;
-
-	spin_lock_irqsave(&hostdata->lock, flags);
-
-#if (NDEBUG & NDEBUG_ANY)
-	scmd_printk(KERN_INFO, cmd, __func__);
-#endif
-	NCR5380_dprint(NDEBUG_ANY, instance);
-	NCR5380_dprint_phase(NDEBUG_ANY, instance);
-
-	if (list_del_cmd(&hostdata->unissued, cmd)) {
-		dsprintk(NDEBUG_ABORT, instance,
-		         "abort: removed %p from issue queue\n", cmd);
-		cmd->result = DID_ABORT << 16;
-		cmd->scsi_done(cmd); /* No tag or busy flag to worry about */
-		goto out;
-	}
-
-	if (hostdata->selecting == cmd) {
-		dsprintk(NDEBUG_ABORT, instance,
-		         "abort: cmd %p == selecting\n", cmd);
-		hostdata->selecting = NULL;
-		cmd->result = DID_ABORT << 16;
-		complete_cmd(instance, cmd);
-		goto out;
-	}
-
-	if (list_del_cmd(&hostdata->disconnected, cmd)) {
-		dsprintk(NDEBUG_ABORT, instance,
-		         "abort: removed %p from disconnected list\n", cmd);
-		/* Can't call NCR5380_select() and send ABORT because that
-		 * means releasing the lock. Need a bus reset.
-		 */
-		set_host_byte(cmd, DID_ERROR);
-		complete_cmd(instance, cmd);
-		result = FAILED;
-		goto out;
-	}
-
-	if (hostdata->connected == cmd) {
-		dsprintk(NDEBUG_ABORT, instance, "abort: cmd %p is connected\n", cmd);
-		hostdata->connected = NULL;
-		hostdata->dma_len = 0;
-		if (do_abort(instance)) {
-			set_host_byte(cmd, DID_ERROR);
-			complete_cmd(instance, cmd);
-			result = FAILED;
-			goto out;
-		}
-		set_host_byte(cmd, DID_ABORT);
-		complete_cmd(instance, cmd);
-		goto out;
-	}
-
-	if (list_del_cmd(&hostdata->autosense, cmd)) {
-		dsprintk(NDEBUG_ABORT, instance,
-		         "abort: removed %p from sense queue\n", cmd);
-		set_host_byte(cmd, DID_ERROR);
-		complete_cmd(instance, cmd);
-	}
-
-out:
-	if (result == FAILED)
-		dsprintk(NDEBUG_ABORT, instance, "abort: failed to abort %p\n", cmd);
-	else
-		dsprintk(NDEBUG_ABORT, instance, "abort: successfully aborted %p\n", cmd);
-
-	queue_work(hostdata->work_q, &hostdata->main_task);
-	maybe_release_dma_irq(instance);
-	spin_unlock_irqrestore(&hostdata->lock, flags);
-
-	return result;
-}
-
-
-/**
- * NCR5380_bus_reset - reset the SCSI bus
- * @cmd: SCSI command undergoing EH
- *
- * Returns SUCCESS
- */
-
-static int NCR5380_bus_reset(struct scsi_cmnd *cmd)
-{
-	struct Scsi_Host *instance = cmd->device->host;
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-	int i;
-	unsigned long flags;
-	struct NCR5380_cmd *ncmd;
-
-	spin_lock_irqsave(&hostdata->lock, flags);
-
-#if (NDEBUG & NDEBUG_ANY)
-	scmd_printk(KERN_INFO, cmd, __func__);
-#endif
-	NCR5380_dprint(NDEBUG_ANY, instance);
-	NCR5380_dprint_phase(NDEBUG_ANY, instance);
-
-	do_reset(instance);
-
-	/* reset NCR registers */
-	NCR5380_write(MODE_REG, MR_BASE);
-	NCR5380_write(TARGET_COMMAND_REG, 0);
-	NCR5380_write(SELECT_ENABLE_REG, 0);
-
-	/* After the reset, there are no more connected or disconnected commands
-	 * and no busy units; so clear the low-level status here to avoid
-	 * conflicts when the mid-level code tries to wake up the affected
-	 * commands!
-	 */
-
-	if (list_del_cmd(&hostdata->unissued, cmd)) {
-		cmd->result = DID_RESET << 16;
-		cmd->scsi_done(cmd);
-	}
-
-	if (hostdata->selecting) {
-		hostdata->selecting->result = DID_RESET << 16;
-		complete_cmd(instance, hostdata->selecting);
-		hostdata->selecting = NULL;
-	}
-
-	list_for_each_entry(ncmd, &hostdata->disconnected, list) {
-		struct scsi_cmnd *cmd = NCR5380_to_scmd(ncmd);
-
-		set_host_byte(cmd, DID_RESET);
-		cmd->scsi_done(cmd);
-	}
-	INIT_LIST_HEAD(&hostdata->disconnected);
-
-	list_for_each_entry(ncmd, &hostdata->autosense, list) {
-		struct scsi_cmnd *cmd = NCR5380_to_scmd(ncmd);
-
-		set_host_byte(cmd, DID_RESET);
-		cmd->scsi_done(cmd);
-	}
-	INIT_LIST_HEAD(&hostdata->autosense);
-
-	if (hostdata->connected) {
-		set_host_byte(hostdata->connected, DID_RESET);
-		complete_cmd(instance, hostdata->connected);
-		hostdata->connected = NULL;
-	}
-
-#ifdef SUPPORT_TAGS
-	free_all_tags(hostdata);
-#endif
-	for (i = 0; i < 8; ++i)
-		hostdata->busy[i] = 0;
-	hostdata->dma_len = 0;
-
-	queue_work(hostdata->work_q, &hostdata->main_task);
-	maybe_release_dma_irq(instance);
-	spin_unlock_irqrestore(&hostdata->lock, flags);
-
-	return SUCCESS;
-}
diff --git a/drivers/scsi/atari_scsi.c b/drivers/scsi/atari_scsi.c
index 445c267..49b7b14 100644
--- a/drivers/scsi/atari_scsi.c
+++ b/drivers/scsi/atari_scsi.c
@@ -87,9 +87,6 @@
 
 /* Definitions for the core NCR5380 driver. */
 
-#define SUPPORT_TAGS
-#define MAX_TAGS                        32
-
 #define NCR5380_implementation_fields   /* none */
 
 #define NCR5380_read(reg)               atari_scsi_reg_read(reg)
@@ -189,8 +186,6 @@
 module_param(setup_cmd_per_lun, int, 0);
 static int setup_sg_tablesize = -1;
 module_param(setup_sg_tablesize, int, 0);
-static int setup_use_tagged_queuing = -1;
-module_param(setup_use_tagged_queuing, int, 0);
 static int setup_hostid = -1;
 module_param(setup_hostid, int, 0);
 static int setup_toshiba_delay = -1;
@@ -479,8 +474,7 @@
 		setup_sg_tablesize = ints[3];
 	if (ints[0] >= 4)
 		setup_hostid = ints[4];
-	if (ints[0] >= 5)
-		setup_use_tagged_queuing = ints[5];
+	/* ints[5] (use_tagged_queuing) is ignored */
 	/* ints[6] (use_pdma) is ignored */
 	if (ints[0] >= 7)
 		setup_toshiba_delay = ints[7];
@@ -853,9 +847,6 @@
 	instance->irq = irq->start;
 
 	host_flags |= IS_A_TT() ? 0 : FLAG_LATE_DMA_SETUP;
-#ifdef SUPPORT_TAGS
-	host_flags |= setup_use_tagged_queuing > 0 ? FLAG_TAGGED_QUEUING : 0;
-#endif
 	host_flags |= setup_toshiba_delay > 0 ? FLAG_TOSHIBA_DELAY : 0;
 
 	error = NCR5380_init(instance, host_flags);
diff --git a/drivers/scsi/mac_scsi.c b/drivers/scsi/mac_scsi.c
index 4de6589..42feba7 100644
--- a/drivers/scsi/mac_scsi.c
+++ b/drivers/scsi/mac_scsi.c
@@ -55,8 +55,6 @@
 module_param(setup_sg_tablesize, int, 0);
 static int setup_use_pdma = -1;
 module_param(setup_use_pdma, int, 0);
-static int setup_use_tagged_queuing = -1;
-module_param(setup_use_tagged_queuing, int, 0);
 static int setup_hostid = -1;
 module_param(setup_hostid, int, 0);
 static int setup_toshiba_delay = -1;
@@ -95,8 +93,7 @@
 		setup_sg_tablesize = ints[3];
 	if (ints[0] >= 4)
 		setup_hostid = ints[4];
-	if (ints[0] >= 5)
-		setup_use_tagged_queuing = ints[5];
+	/* ints[5] (use_tagged_queuing) is ignored */
 	if (ints[0] >= 6)
 		setup_use_pdma = ints[6];
 	if (ints[0] >= 7)
@@ -382,9 +379,6 @@
 	} else
 		host_flags |= FLAG_NO_PSEUDO_DMA;
 
-#ifdef SUPPORT_TAGS
-	host_flags |= setup_use_tagged_queuing > 0 ? FLAG_TAGGED_QUEUING : 0;
-#endif
 	host_flags |= setup_toshiba_delay > 0 ? FLAG_TOSHIBA_DELAY : 0;
 
 	error = NCR5380_init(instance, host_flags | FLAG_LATE_DMA_SETUP);
diff --git a/drivers/scsi/sun3_scsi.c b/drivers/scsi/sun3_scsi.c
index f2fc788..3c4c070 100644
--- a/drivers/scsi/sun3_scsi.c
+++ b/drivers/scsi/sun3_scsi.c
@@ -41,9 +41,6 @@
 
 /* Definitions for the core NCR5380 driver. */
 
-/* #define SUPPORT_TAGS */
-/* #define MAX_TAGS                     32 */
-
 #define NCR5380_implementation_fields   /* none */
 
 #define NCR5380_read(reg)               sun3scsi_read(reg)
@@ -75,10 +72,6 @@
 module_param(setup_cmd_per_lun, int, 0);
 static int setup_sg_tablesize = -1;
 module_param(setup_sg_tablesize, int, 0);
-#ifdef SUPPORT_TAGS
-static int setup_use_tagged_queuing = -1;
-module_param(setup_use_tagged_queuing, int, 0);
-#endif
 static int setup_hostid = -1;
 module_param(setup_hostid, int, 0);
 
@@ -512,10 +505,6 @@
 	instance->io_port = (unsigned long)ioaddr;
 	instance->irq = irq->start;
 
-#ifdef SUPPORT_TAGS
-	host_flags |= setup_use_tagged_queuing > 0 ? FLAG_TAGGED_QUEUING : 0;
-#endif
-
 	error = NCR5380_init(instance, host_flags);
 	if (error)
 		goto fail_init;